Korea, Republic of
Analysis of Hydrogen Filling of 175 Liter Tank for Large-Sized Hydrogen Vehicle
May 2022
Publication
Due to the low density of hydrogen gas under ambient temperature and atmospheric pressure conditions the high-pressure gaseous hydrogen storage method is widely employed. With high-pressure characteristics of hydrogen storage rigorous safety precautions are required such as filling of compressed gas in a hydrogen tank to achieve reliable operational solutions. Especially for the large-sized tanks (above 150 L) safety operation of hydrogen storage should be considered. In the present study the compressed hydrogen gas behavior in a large hydrogen tank of 175 L is investigated for its filling. To validate the numerical approach used in this study numerical models for the adaptation of the gas and turbulence models are examined. Numerical parametric studies on hydrogen filling for the large hydrogen tank of 175 L are conducted to estimate the hydrogen gas behavior in the hydrogen tank under various conditions of state of charge of pressure and ambient temperature. From the parametric studies the relationship between the initial SOC pressure condition and the maximum temperature rise of hydrogen gas was shown. That is the maximum temperature rise increases as the ambient temperature decreases and the rise increases as the SOC decreases.
Charpy Impact Properties of Hydrogen-Exposed 316L Stainless Steel at Ambient and Cryogenic Temperatures
May 2019
Publication
316L stainless steel is a promising material candidate for a hydrogen containment system. However when in contact with hydrogen the material could be degraded by hydrogen embrittlement (HE). Moreover the mechanism and the effect of HE on 316L stainless steel have not been clearly studied. This study investigated the effect of hydrogen exposure on the impact toughness of 316L stainless steel to understand the relation between hydrogen charging time and fracture toughness at ambient and cryogenic temperatures. In this study 316L stainless steel specimens were exposed to hydrogen in different durations. Charpy V-notch (CVN) impact tests were conducted at ambient and low temperatures to study the effect of HE on the impact properties and fracture toughness of 316L stainless steel under the tested temperatures. Hydrogen analysis and scanning electron microscopy (SEM) were conducted to find the effect of charging time on the hydrogen concentration and surface morphology respectively. The result indicated that exposure to hydrogen decreased the absorbed energy and ductility of 316L stainless steel at all tested temperatures but not much difference was found among the pre-charging times. Another academic insight is that low temperatures diminished the absorbed energy by lowering the ductility of 316L stainless steel
A Comprehensive Review of Microbial Electrolysis Cells (MEC) Reactor Designs and Configurations for Sustainable Hydrogen Gas Production
Nov 2015
Publication
Hydrogen gas has tremendous potential as an environmentally acceptable energy carrier for vehicles. A cutting edge technology called a microbial electrolysis cell (MEC) can achieve sustainable and clean hydrogen production from a wide range of renewable biomass and wastewaters. Enhancing the hydrogen production rate and lowering the energy input are the main challenges of MEC technology. MEC reactor design is one of the crucial factors which directly influence on hydrogen and current production rate in MECs. The rector design is also a key factor to upscaling. Traditional MEC designs incorporated membranes but it was recently shown that membrane-free designs can lead to both high hydrogen recoveries and production rates. Since then multiple studies have developed reactors that operate without membranes. This review provides a brief overview of recent advances in research on scalable MEC reactor design and configurations.
Multi-Period Planning of Hydrogen Supply Network for Refuelling Hydrogen Fuel Cell Vehicles in Urban Areas
May 2020
Publication
The hydrogen economy refers to an economic and industrial structure that uses hydrogen as its main energy source replacing traditional fossil-fuel-based energy systems. In particular the widespread adoption of hydrogen fuel cell vehicles (HFCVs) is one of the key factors enabling a hydrogen economy and aggressive investment in hydrogen refuelling infrastructure is essential to make large-scale adoption of HFCVs possible. In this study we address the problem of effectively designing a hydrogen supply network for refuelling HFCVs in urban areas relatively far from a large hydrogen production site such as a petrochemical complex. In these urban areas where mass supply of hydrogen is not possible hydrogen can be supplied by reforming city gas. In this case building distributed hydrogen production bases that extract large amounts of hydrogen from liquefied petroleum gas (LPG) or compressed natural gas (CNG) and then supply hydrogen to nearby hydrogen stations may be a cost-effective option for establishing a hydrogen refuelling infrastructure in the early stage of the hydrogen economy. Therefore an optimization model is proposed for effectively deciding when and where to build hydrogen production bases and hydrogen refuelling stations in an urban area. Then a case study of the southeastern area of Seoul known as a commercial and residential center is discussed. A variety of scenarios for the design parameters of the hydrogen supply network are analyzed based on the target of the adoption of HFCVs in Seoul by 2030. The proposed optimization model can be effectively used for determining the time and sites for building hydrogen production bases and hydrogen refuelling stations.
MELCOR Analysis of a SPARC Experiment for Spray-PAR Interaction During a Hydrogen Release
Oct 2020
Publication
A series of experiments were performed in the SPARC (spray-aerosol-recombiner-combustion) test facility to simulate a hydrogen mitigation system with the actuation of a PAR (passive auto-catalytic re-combiner) and spray system. In this study the SPARC-SPRAY-PAR (SSP1) experiment is chosen to benchmark the MELCOR (a lumped-parameter code for severe accident analysis) predictions against test data. For this purpose firstly we prepared the base input model of the SPARC test vessel and tested it by a simple verification problem with well-defined boundary conditions. The implementation of a currently used PAR correlation in MELCOR is shown to be appropriate for the simulation of a PAR actuation experiment. In an SSP1 experiment the PAR is reacting with hydrogen and the spray actuation starts as soon as hydrogen injection is complete. The MELCOR simulation well predicts the pressure behavior and the gas flow affected by operating both a PAR and spray system. However the local hydrogen concentration measurement near the inlet nozzle is much higher than the volume average-value by MELCOR since high jet flow from the nozzle is dispersed in the corresponding cell volume. The experimental reproduction of the phenomena we expect or conversely the identification of phenomena we do not understand will continue to support the verification of analytical models using experimental data and to analyze the impact of spray on PAR operations in severe accident conditions.
South Korea’s Big Move to Hydrogen Society
Nov 2020
Publication
Extensive energy consumption has become a major concern due to increase of greenhouse gas emissions and global warming. Hence hydrogen has attracted attention as a green fuel with zero carbon emission for green transportation through production of electric vehicles with hydrogen fuel cells. South Korea has launched a hydrogen society policy with the objective of expanding production of hydrogen from renewable energy sources. The hydrogen economy will play a critical role in reducing atmospheric pollution and global arming. However new development of infrastructure for hydrogen refuelling and increasing awareness of the hydrogen economy is required together with reduced prices of hydrogen-driven vehicles that are promising options for a sustainable green hydrogen economy.
Review of the Durability of Polymer Electrolyte Membrane Fuel Cell in Long-Term Operation: Main Influencing Parameters and Testing Protocols
Jul 2021
Publication
Durability is the most pressing issue preventing the efficient commercialization of polymer electrolyte membrane fuel cell (PEMFC) stationary and transportation applications. A big barrier to overcoming the durability limitations is gaining a better understanding of failure modes for user profiles. In addition durability test protocols for determining the lifetime of PEMFCs are important factors in the development of the technology. These methods are designed to gather enough data about the cell/stack to understand its efficiency and durability without causing it to fail. They also provide some indication of the cell/stack’s age in terms of changes in performance over time. Based on a study of the literature the fundamental factors influencing PEMFC long-term durability and the durability test protocols for both PEMFC stationary and transportation applications were discussed and outlined in depth in this review. This brief analysis should provide engineers and researchers with a fast overview as well as a useful toolbox for investigating PEMFC durability issues.
Optimal Facility Combination Set of Integrated Energy System Based on Consensus Point between Independent System Operator and Independent Power Producer
Dec 2022
Publication
In recent years the frequency of power demand imbalance and negative price phenomenon has risen due to the rapid expansion of renewable energy sources (RES). Because of this a means to reduce the curtailment of RES by utilizing surplus energy is essential. This paper focuses on reducing the curtailment of wind turbines (WT) with high output intermittency and minimizing the investment cost of IES via an integrated energy system (IES). The IES operation seeks to improve the acceptability and efficiency of the RES as it supports the integration of various energies mix such as electricity heat hydrogen. This paper proposes an optimal facility combination set (FCS) of IES that satisfies the requirements of ISO and IPP using Multi-Objective Optimization Programming (MOP). The case study is based on a wind farm in South Korea set in Aewol-eup Jeju-Island. The case study results provide the best configuration of the IES energy mix with the best economic value and efficiency while satisfying ISO and IPP perspectives.
A Study on the Joule-Thomson Effect of During Filling Hydrogen in High Pressure Tank
Dec 2022
Publication
With the development of the hydrogen fuel cell automobile industry higher requirements are put forward for the construction of hydrogen energy infrastructure the matching of parameters and the control strategy of hydrogen filling rate in the hydrogenation process of hydrogenation station. Fuel for hydrogen fuel cell vehicles comes from hydrogen refueling stations. At present the technological difficulty of hydrogenation is mainly reflected in the balanced treatment of reducing the temperature rise of hydrogen and shortening the filling time during the fast filling process. The Joule-Thomson (JT) effect occurs when high-pressure hydrogen gas passes through the valve assembly which may lead to an increase in hydrogen temperature. The JT effect is generally reflected by the JT coefficient. According to the high pressure hydrogen in the pressure reducing valve the corresponding JT coefficients were calculated by using the VDW equation RK equation SRK equation and PR equation and the expression of JT effect temperature rise was deduced which revealed the hydrogen temperature variation law in the process of reducing pressure. Make clear the relationship between charging parameters and temperature rise in the process of decompression; the flow and thermal characteristics of hydrogen in the process of decompression are revealed. This study provides basic support for experts to achieve throttling optimization of related pressure control system in hydrogen industry
Scenario-Based Techno-Economic Analysis of Steam Methane Reforming Process for Hydrogen Production
Jun 2021
Publication
Steam methane reforming (SMR) process is regarded as a viable option to satisfy the growing demand for hydrogen mainly because of its capability for the mass production of hydrogen and the maturity of the technology. In this study an economically optimal process configuration of SMR is proposed by investigating six scenarios with different design and operating conditions including CO2 emission permits and CO2 capture and sale. Of the six scenarios the process configuration involving CO2 capture and sale is the most economical with an H2 production cost of $1.80/kg-H2. A wide range of economic analyses is performed to identify the tradeoffs and cost drivers of the SMR process in the economically optimal scenario. Depending on the CO2 selling price and the CO2 capture cost the economic feasibility of the SMR-based H2 production process can be further improved.
Study on Behavior of Ambient Hydraulic Cycling Test for 70 MPA Type-3 Hydrogen Composite Cylinder
Sep 2013
Publication
Hydrogen used in hydrogen fuel cell vehicles is the flammable gas which has wide flammable range and flame propagation speed is very fast. This fuel cell vehicle equipped with high-pressure vessel in the form of fuel to supply the high pressure hydrogen storage system needs to be checked carefully about a special safety design and exact weak point for high pressure repeated fatigue. 70 L liner and 70 MPa Type-3 vessel were tested using the equipments which can perform ambient hydraulic cycling test and burst test in the Korea Gas Safety Corporation. And it was performed to identify the internal external behaviour through the Finite Element Analysis (FEA) and real leakage mode for high pressure repeated fatigue when subjected to be pressurized in vessel. 70 L liner and 70 MPa Type-3 vessel were tested using the equipments which can perform ambient hydraulic cycling test and burst test in the Korea Gas Safety Corporation. And it was performed to identify the internal external behaviour through the Finite Element Analysis (FEA) and real leakage mode for high pressure repeated fatigue when subjected to be pressurized in vessel. Through this study liner of type-3 hydrogen vessel is ruptured first on cylindrical (body) part than Dome part in 8.5 MPa. Also the same Phenomena are confirmed through the Finite Element Analysis (FEA). External composite leakage mode in ambient hydraulic cycling test was occurred in different area such as the Dome Dome knuckle and cylindrical (body) parts. But cracks of inner liner for gas tight were occurred in only cylindrical (body) parts. Also in FEA results when vessel is pressurized Dome knuckle and cylindrical (body) parts is weakest among all parts because of expansion of cylindrical (body) parts.
Advanced Sizing Methodology for a Multi-Mode eVTOL UAV Powered by a Hydrogen Fuel Cell and Battery
Jan 2022
Publication
A critical drawback of battery-powered eVTOL UAVs is their limited range and endurance and this drawback could be solved by using a combination of hydrogen fuel cells and batteries. The objective of this paper is to develop a sizing methodology for the lift+cruise-type eVTOL UAV powered by a hydrogen fuel cell and battery. This paper presents the constraints analysis method for forward flight/VTOL multi-mode UAV the regression model for electric propulsion system sizing a sizing method for an electric propulsion system and hydrogen fuel cell system and a transition analysis method. The total mass of the UAV is iteratively calculated until convergence and the optimization method is used to ensure that the sizing results satisfy the design requirements. The sizing results are the UAV’s geometry mass and power data. To verify the accuracy of the proposed sizing methodology the sizing and the conceptual design phase results of a 25 kg hydrogen fuel-cell-powered UAV are compared. All parameters had an error within 10% and satisfied the design requirements.
Prediction of Hydrogen Concentration in Containment During Severe Accidents Using Fuzzy Neural Network
Jan 2015
Publication
Recently severe accidents in nuclear power plants (NPPs) have become a global concern. The aim of this paper is to predict the hydrogen buildup within containment resulting from severe accidents. The prediction was based on NPPs of an optimized power reactor 1000. The increase in the hydrogen concentration in severe accidents is one of the major factors that threaten the integrity of the containment. A method using a fuzzy neural network (FNN) was applied to predict the hydrogen concentration in the containment. The FNN model was developed and verified based on simulation data acquired by simulating MAAP4 code for optimized power reactor 1000. The FNN model is expected to assist operators to prevent a hydrogen explosion in severe accident situations and manage the accident properly because they are able to predict the changes in the trend of hydrogen concentration at the beginning of real accidents by using the developed FNN model.
Experimental and Theoretical Insights to Demonstrate the Hydrogen Evolution Activity of Layered Platinum Dichalcogenides Electrocatalysts
Mar 2021
Publication
Hydrogen is a highly efficient and clean renewable energy source and water splitting through electrocatalytic hydrogen evolution is a most promising approach for hydrogen generation. Layered transition metal dichalcogenides-based nano-structures have recently attracted significant interest as robust and durable catalysts for hydrogen evolution. We systematically investigated the platinum (Pt) based dichalcogenides (PtS2 PtSe2 and PtTe2) as highly energetic and robust hydrogen evolution electrocatalysts. PtTe2 catalyst unveiled the rapid hydrogen evolution process with the low overpotentials of 75 and 92 mV (vs. RHE) at a current density of 10 mA cm−2 and the small Tafel slopes of 64 and 59 mV/dec in acidic and alkaline medium respectively. The fabricated PtTe2 electrocatalyst explored a better catalytic activity than PtS2 and PtSe2. The density functional theory estimations explored that the observed small Gibbs free energy for H-adsorption of PtTe2 was given the prominent role to achieve the superior electrocatalytic and excellent stability activity towards hydrogen evolution due to a smaller bandgap and the metallic nature. We believe that this work will offer a key path to use Pt based dichalcogenides for hydrogen evolution electrocatalysts.
Effect of Hydrogen and Strain-Induced Martensite on Mechanical Properties of AISI 304 Stainless Steel
Jul 2016
Publication
Plastic deformation and strain-induced martensite (SIM α′) transformation in metastable austenitic AISI 304 stainless steel were investigated through room temperature tensile tests at strain rates ranging from 2 × 10−6 to 2 × 10−2/s. The amount of SIM was measured on the fractured tensile specimens using a feritscope and magnetic force microscope. Elongation to fracture tensile strength hardness and the amount of SIM increased with decreasing the strain rate. The strain-rate dependence of RT tensile properties was observed to be related to the amount of SIM. Specifically SIM formed during tensile tests was beneficial in increasing the elongation to fracture hardness and tensile strength. Hydrogen suppressed the SIM formation leading to hydrogen softening and localized brittle fracture.
Recent Progress in Hydrogen Flammability Prediction for the Safe Energy Systems
Nov 2020
Publication
Many countries consider hydrogen as a promising energy source to resolve the energy challenges over the global climate change. However the potential of hydrogen explosions remains a technical issue to embrace hydrogen as an alternate solution since the Hindenburg disaster occurred in 1937. To ascertain safe hydrogen energy systems including production storage and transportation securing the knowledge concerning hydrogen flammability is essential. In this paper we addressed a comprehensive review of the studies related to predicting hydrogen flammability by dividing them into three types: experimental numerical and analytical. While the earlier experimental studies had focused only on measuring limit concentration recent studies clarified the extinction mechanism of a hydrogen flame. In numerical studies the continued advances in computer performance enabled even multi-dimensional stretched flame analysis following one-dimensional planar flame analysis. The different extinction mechanisms depending on the Lewis number of each fuel type could be observed by these advanced simulations. Finally historical attempts to predict the limit concentration by analytical modelling of flammability characteristics were discussed. Developing an accurate model to predict the flammability limit of various hydrogen mixtures is our remaining issue.
Evaluation of Hydrogen Permeation Characteristics in Rubbery Polymers
Oct 2020
Publication
To find suitable sealing material with low permeability against hydrogen the elaborated evaluation techniques for hydrogen transport properties are necessary. We developed two techniques determining the permeability of hydrogen including software for diffusion behavior analysis. The techniques contain gas chromatography and volumetric collection of hydrogen gas. By measuring the hydrogen released from polymer samples with respect to the elapsed time after being decompressed from the high pressure total amount of adsorption and diffusivity (D) of hydrogen are evaluated with self-developed program of Fick's diffusion equation specified to a sample shape. The solubility (S) and permeability (P) of the polymers are determined through Henry's law and a relation of P=SD respectively. Developed techniques were applied to three kinds of spherical-shaped sealing rubbers NBR EPDM and FKM. The D S and P have been measured as function of pressure. The permeability obtained by both methods are discussed with Comsol simulation.
Development of Visible-Light-Driven Rh–TiO2-CeO2 Hybrid Photocatalysts for Hydrogen Production
Jul 2021
Publication
Visible-light-driven hydrogen production through photocatalysis has attracted enormous interest owing to its great potential to address energy and environmental issues. However photocatalysis possesses several limitations to overcome for practical applications such as low light absorption efficiency rapid charge recombination and poor stability of photocatalysts. Here the preparation of efficient noble metal–semiconductor hybrid photocatalysts for photocatalytic hydrogen production is presented. The prepared ternary Rh–TiO2–CeO2 hybrid photocatalysts exhibited excellent photocatalytic performance toward the hydrogen production reaction compared with their counterparts ascribed to the synergistic combination of Rh TiO2 and CeO2.
Risk Assessment Method Combining Independent Protection Layers (IPL) of Layer of Protection Analysis (LOPA) and RISKCURVES Software: Case Study of Hydrogen Refueling Stations in Urban Areas
Jul 2021
Publication
The commercialization of eco-friendly hydrogen vehicles has elicited attempts to expand hydrogen refueling stations in urban areas; however safety measures to reduce the risk of jet fires have not been established. The RISKCURVES software was used to evaluate the individual and societal risks of hydrogen refueling stations in urban areas and the F–N (Frequency–Number of fatalities) curve was used to compare whether the safety measures satisfied international standards. From the results of the analysis it was found that there is a risk of explosion in the expansion of hydrogen refueling stations in urban areas and safety measures should be considered. To lower the risk of hydrogen refueling stations this study applied the passive and active independent protection layers (IPLs) of LOPA (Layer of Protection Analysis) and confirmed that these measures significantly reduced societal risk as well as individual risk and met international standards. In particular such measures could effectively reduce the impact of jet fire in dispensers and tube trailers that had a high risk. Measures employing both IPL types were efficient in meeting international standard criteria; however passive IPLs were found to have a greater risk reduction effect than active IPLs. The combination of RISKCURVES and LOPA is an appropriate risk assessment method that can reduce work time and mitigate risks through protective measures compared to existing risk assessment methods. This method can be applied to risk assessment and risk mitigation not only for hydrogen facilities but also for hazardous materials with high fire or explosion risk.
Recent Advances in Carbon Dioxide Conversion: A Circular Bioeconomy Perspective
Jun 2021
Publication
Managing the concentration of atmospheric CO2 requires a multifaceted engineering strategy which remains a highly challenging task. Reducing atmospheric CO2 (CO2R) by converting it to value-added chemicals in a carbon neutral footprint manner must be the ultimate goal. The latest progress in CO2R through either abiotic (artificial catalysts) or biotic (natural enzymes) processes is reviewed herein. Abiotic CO2R can be conducted in the aqueous phase that usually leads to the formation of a mixture of CO formic acid and hydrogen. By contrast a wide spectrum of hydrocarbon species is often observed by abiotic CO2R in the gaseous phase. On the other hand biotic CO2R is often conducted in the aqueous phase and a wide spectrum of value-added chemicals are obtained. Key to the success of the abiotic process is understanding the surface chemistry of catalysts which significantly governs the reactivity and selectivity of CO2R. However in biotic CO2R operation conditions and reactor design are crucial to reaching a neutral carbon footprint. Future research needs to look toward neutral or even negative carbon footprint CO2R processes. Having a deep insight into the scientific and technological aspect of both abiotic and biotic CO2R would advance in designing efficient catalysts and microalgae farming systems. Integrating the abiotic and biotic CO2R such as microbial fuel cells further diversifies the spectrum of CO2R.
Hydrogen Production Possibility using Mongolian Renewable Energy
Jan 2019
Publication
There is widespread popular support for using renewable energy particularly solar and wind energy which provide electricity without giving rise to any carbon dioxide emissions. Harnessing these for electricity depends on the cost and efficiency of the technology which is constantly improving thus reducing costs per peak kilowatt and per kWh. Utilizing solar and wind-generated electricity in a stand-alone system requires corresponding battery or other storage capacity. The possibility of large-scale use of hydrogen in the future as a transport fuel increases the potential for both renewables and base-load electricity supply.
Electrical Double Layer Mechanism Analysis of PEM Water Electrolysis for Frequency Limitation of Pulsed Currents
Nov 2021
Publication
This paper proposes a method for improving hydrogen generation using pulse current in a proton exchange membrane-type electrolyzer (PEMEL). Traditional methods of electrolysis using direct current are known as the simplest approach to produce hydrogen. However it is highly dependent on environmental variables such as the temperature and catalyst used to enhance the rate of electrolysis. Therefore we propose electrolysis using a pulse current that can apply several dependent variables rather than environmental variables. The proposed method overcomes the difficulties in selecting the frequency of the pulse current by deriving factors affecting hydrogen generation while changing the concentration generated by the cell interface during the pulsed water-electrolysis process. The correlation between the electrolyzer load and the frequency characteristics was analyzed and the limit value of the applicable frequency of the pulse current was derived through electrical modeling. In addition the operating characteristics of PEMEL could be predicted and the PEMEL using the proposed pulse current was verified through experiments.
Evaluation Techniques of Hydrogen Permeation in Sealing Rubber Materials
Dec 2020
Publication
Three techniques for determining the hydrogen permeation properties of rubber samples were developed based on the volumetric and gravimetric measurements of released H2 gas after sample decompression. These methods include gas chromatography (GC) by thermal desorption analysis (TDA) volumetric collection (VC) measurement of hydrogen by graduated cylinder and gravimetric (GM) measurement by electronic balance. By measuring the released hydrogen against elapsed time after the decompression of pressure the charging amount (C0) and diffusivity (D) were obtained with the developed diffusion analysis program. From these values the solubility (S) and permeability (P) of polymers were evaluated through the relations of Henry's law and P=SD respectively. The developed techniques were applied to three kinds of spherically shaped sealing rubber materials. D S and P were analyzed as a function of pressure. The transport behaviors obtained in the three methods are discussed and compared with the characteristics of each measuring technique. The correlations between transport parameters and carbon black filler or density are discussed.
The Role of Hydrogen in Hydrogen Embrittlement of Metals: The Case of Stainless Steel
Apr 2019
Publication
Hydrogen embrittlement (HE) of metals has remained a mystery in materials science for more than a century. To try to clarify this mystery tensile tests were conducted at room temperature (RT) on a 316 stainless steel (SS) in air and hydrogen of 70 MPa. With an aim to directly observe the effect of hydrogen on ordering of 316 SS during deformation electron diffraction patterns and images were obtained from thin foils made by a focused ion beam from the fracture surfaces of the tensile specimens. To prove lattice contraction by ordering a 40% CW 316 SS specimen was thermally aged at 400 °C to incur ordering and its lattice contraction by ordering was determined using neutron diffraction by measuring its lattice parameters before and after aging. We demonstrate that atomic ordering is promoted by hydrogen leading to formation of short-range order and a high number of planar dislocations in the 316 SS and causing its anisotropic lattice contraction. Hence hydrogen embrittlement of metals is controlled by hydrogen-enhanced ordering during RT deformation in hydrogen. Hydrogen-enhanced ordering will cause the ordered metals to be more resistant to HE than the disordered ones which is evidenced by the previous observations where furnace-cooled metals with order are more resistant to HE than water-quenched or cold worked metals with disorder. This finding strongly supports our proposal that strain-induced martensite is a disordered phase.
A Study on the Characteristics of Academic Topics Related to Renewable Energy Using the Structural Topic Modelling and the Weak Signal Concept
Mar 2021
Publication
It is important to examine in detail how the distribution of academic research topics related to renewable energy is structured and which topics are likely to receive new attention in the future in order for scientists to contribute to the development of renewable energy. This study uses an advanced probabilistic topic modeling to statistically examine the temporal changes of renewable energy topics by using academic abstracts from 2010–2019 and explores the properties of the topics from the perspective of future signs such as weak signals. As a result in strong signals methods for optimally integrating renewable energy into the power grid are paid great attention. In weak signals interest in large-capacity energy storage systems such as hydrogen supercapacitors and compressed air energy storage showed a high rate of increase. In not-strong-but-well-known signals comprehensive topics have been included such as renewable energy potential barriers and policies. The approach of this study is applicable not only to renewable energy but also to other subjects.
Baking Effect on Desorption of Diffusible Hydrogen and Hydrogen Embrittlement on Hot-Stamped Boron Martensitic Steel
Jun 2019
Publication
Recently hot stamping technology has been increasingly used in automotive structural parts with ultrahigh strength to meet the standards of both high fuel efficiency and crashworthiness. However one issue of concern regarding these martensitic steels which are fabricated using a hot stamping procedure is that the steel is highly vulnerable to hydrogen delayed cracking caused by the diffusible hydrogen flow through the surface reaction of the coating in a furnace atmosphere. One way to make progress in understanding hydrogen delayed fractures is to elucidate an interaction for desorption with diffusible hydrogen behavior. The role of diffusible hydrogen on delayed fractures was studied for different baking times and temperatures in a range of automotive processes for hot-stamped martensitic steel with aluminum- and silicon-coated surfaces. It was clear that the release of diffusible hydrogen is effective at higher temperatures and longer times making the steel less susceptible to hydrogen delayed fractures. Using thermal desorption spectroscopy the phenomenon of the hydrogen delayed fracture was attributed to reversible hydrogen in microstructure sites with low trapping energy.
UV Assisted on Titanium Doped Electrode for Hydrogen Evolution from Artificial Wastewater
Jul 2018
Publication
Formaldehyde (H2CO) is the harmful chemical that used in variety of industries. However there are many difficulties to treat discharged H2CO in the wastewater. Hydrogen energy is arising as a one of the renewable energy that can replace fossil fuel. Many researches have been conducted on hydrogen production from electrolysis using expensive metal electrodes and catalysts such as platinum (Pt) and palladium (Pd). However they are expensive and have obstacles to directly use from the production. We used copper (Cu) as an electrode substrate because it has a good current density. To avoid corrosion issue of Cu substrate we used commercially available carbon (C) coated Cu substrate and synthesized titanium (Ti) on C/Cu substrate. We found that Ti was well synthesized and stayed on substrate after hydrogen evolution reaction (HER) in artificial wastewater. Moreover we quantified hydrogen production from the wastewater and compared it to pure water. Hydrogen production was enhanced in wastewater and H2CO was decomposed after reaction. We expected to use Ti-C/Cu electrode for hydrogen production of wastewater by electrolysis.
Numerical Analysis for Hydrogen Flame Acceleration during a Severe Accident in the APR1400 Containment Using a Multi-Dimensional Hydrogen Analysis System
Nov 2020
Publication
Korea Atomic Energy Research Institute (KAERI) established a multi-dimensional hydrogen analysis system to evaluate hydrogen release distribution and combustion in the containment of a Nuclear Power Plant (NPP) using MAAP GASFLOW and COM3D. In particular KAERI developed an analysis methodology for a hydrogen flame acceleration on the basis of the COM3D validation results against measured data of the hydrogen combustion tests in the ENACCEF and THAI facilities. The proposed analysis methodology accurately predicted the peak overpressure with an error range of approximately ±10% using the Kawanabe model used for a turbulent flame speed in the COM3D. KAERI performed a hydrogen flame acceleration analysis using the multi-dimensional hydrogen analysis system for a severe accident initiated by a station blackout (SBO) under the assumption of 100% metal–water reaction in the Reactor Pressure Vessel (RPV) to evaluate an overpressure buildup in the containment of the Advanced Power Reactor 1400 MWe (APR1400). The magnitude of the overpressure buildup in the APR1400 containment might be used as a criterion to judge whether the containment integrity is maintained or not when the hydrogen combustion occurs during a severe accident. The COM3D calculation results using the established analysis methodology showed that the calculated peak pressure in the containment was lower than the fracture pressure of the APR1400 containment. This calculation result might have resulted from a large air volume of the containment a reduced hydrogen concentration owing to passive auto-catalytic recombiners installed in the containment during the hydrogen release from the RPV and a lot of stem presence during the hydrogen combustion period in the containment. Therefore we found that the current design of the APR1400 containment maintained its integrity when the flame acceleration occurred during the severe accident initiated by the SBO accident.
High-Order Perturbation Solutions to a Lh2 Spreading Model With Continuous Spill
Sep 2011
Publication
High-order perturbation solutions have been obtained for the simple physical model describing the LH2 spreading with a continuous spill and are shown to improve over the first-order perturbation solutions. The non-dimensional governing equations for the model are derived to obtain more general solutions. Non-dimensional parameters are sought as the governing parameters for the non-dimensional equations and the non-dimensional evaporation rate is used as the perturbation parameter. The results show that the second-order solutions exhibit an improvement over the first-order solutions with respect to the pool volume; however there is still a difference between numerical solutions and second-order solutions in the late stage of spread. Finally it is revealed that the third-order solutions almost agree with numerical solutions.
Hydrogen Embrittlement Behavior of 18Ni 300 Maraging Steel Produced by Selective Laser Melting
Jul 2019
Publication
A study was performed to investigate the hydrogen embrittlement behavior of 18-Ni 300 maraging steel produced by selective laser melting and subjected to different heat treatment strategies. Hydrogen was pre-charged into the tensile samples by an electro-chemical method at the constant current density of 1 A m−2 and 50 A m−2 for 48 h at room temperature. Charged and uncharged specimens were subjected to tensile tests and the hydrogen concentration was eventually analysed using quadrupole mass spectroscopy. After tensile tests uncharged maraging samples showed fracture surfaces with dimples. Conversely in H-charged alloys quasi-cleavage mode fractures occurred. A lower concentration of trapped hydrogen atoms and higher elongation at fracture were measured in the H-charged samples that were subjected to solution treatment prior to hydrogen charging compared to the as-built counterparts. Isothermal aging treatment performed at 460 °C for 8 h before hydrogen charging increased the concentration of trapped hydrogen giving rise to higher hydrogen embrittlement susceptibility.
A Study on the Continuous Spill with Limited Period of Release
Sep 2013
Publication
In this study the spread of cryogenic liquid due to a limited period of release is investigated for the first time to clarify the unclear conventional concept regarding two release types continuous and instantaneous release. In describing instantaneous release a discharge time has been assumed to be infinitesimally small; however such an assumption is unreal because there exists a finite period of release no matter how rapid it is. If the discharge time is less than the entire time domain the instantaneous release model should be added to the continuous model from the end of the time. This combined release that consists of the initial continuous model and subsequent instantaneous model is more realistic than the instantaneous release. The physical phenomenon is governed by three parameters: the evaporation rate per unit area release time and spill quantity. Third-order perturbation solutions are obtained and compared with a numerical solution to verify the perturbation solution. For the same spill quantity the combined model that consists of continuous and subsequent instantaneous model is necessary for small release times whereas the continuous model is only required for large release times. Additionally the combined release model is necessary for a small spill quantity at a fixed release time. These two release models are clearly distinguished using the perturbation solution.
Hydrogen Production by Electrochemical Reaction Using Ethylene Glycol with Terephthalic Acid
Jan 2021
Publication
In this study ethylene glycol (EG) and terephthalic acid (TPA) were used to generate hydrogen using copper electrodes in an alkaline aqueous solution and the corresponding reaction mechanism was experimentally investigated. Both EG and TPA produced hydrogen; however TPA consumed OH− inhibiting the production of intermediary compounds of EG and causing EG to actively react with H2O ultimately leading to enhanced hydrogen production. In addition the initiation potential of water decomposition of the EG and TPA alkaline aqueous solution was 1.0 V; when 1.8 V (vs. RHE) was applied the hydrogen production reached 440 mmol L−1 which was substantially greater than the hydrogen production rate of 150 mmol L−1 during water decomposition.
Experimental Study on a Hydrogen Stratification Induced by PARs Installed in a Containment
Oct 2020
Publication
Hydrogen can be produced in undesired ways such as a high temperature metal oxidation during an accident. In this case the hydrogen must be carefully managed. A hydrogen mitigation system (HMS) should be installed to protect a containment of a nuclear power plant (NPP) from hazards of hydrogen produced by an oxidation of the fuel cladding during a severe accident in an NPP. Among hydrogen removal devices passive auto-catalytic recombiners (PARs) are currently applied to many NPPs because of passive characteristics such as not requiring a power supply nor an operators’ manipulations. However they offer several disadvantages resulting in issues related to hydrogen control by PARs. One of the issues is a hydrogen stratification in which hydrogen is not well-mixed in a compartment due to the high temperature exhaust gas of PARs and accumulation in the lower part. Therefore experimental simulation on hydrogen stratification phenomenon by PARs is required. When the hydrogen stratification by PARs is observed in the experiment the verification and improvement of a PAR analysis model using the experimental results can be performed and the hydrogen removal characteristics by PARs installed in an NPP can be evaluated using the improved PAR model. View Full-Text
Development of NaBH4-Based Hydrogen Generator for Fuel Cell Unmanned Aerial Vehicles with Movable Fuel Cartridge
Mar 2019
Publication
NaBH4-based hydrogen generator for fuel cell Unmanned Aerial Vehicle (UAVs) with movable fuel cartridge was developed in the present study. The main fuel of hydrogen generator is Sodium borohydride (NaBH4) that is a kind of chemical hydride and has a high hydrogen storage density. In the previous studies hydrogen generators were developed in which hydrogen was directly generated from solid state NaBH4. However it was a prototype so inconvenient to replace the fuel after used up and lacked user convenience. Therefore the performance evaluation and the development procedure of NaBH4-based hydrogen generator that was designed taking user convenience in consideration for commercialization were described in this paper.
Comparison of Solutions for a Liquid Pool Spreading Model with Continuous and Instantaneous Spills
Sep 2013
Publication
In this study a solution for a liquid pool spreading model with a continuous spill is compared with that for a liquid pool spreading model with an instantaneous spill under the same total release volume. As reducing spill time in completely releasing liquid from a tank it is evaluated whether the solution for a continuous spill approaches to that for an instantaneous spill or not. Also effects of the viscous term in the liquid pool spreading model with continuous and instantaneous spills on the liquid pool spreading behaviour are investigated.
Continuous Hydrogen Regeneration Through the Oxygen Vacancy Control of Metal Oxides Using Microwave Irradiation
Nov 2018
Publication
The amount of hydrogen gas generated from metal oxide materials based on a thermochemical water-splitting method gradually reduces as the surface of the metal oxide oxidizes during the hydrogen generation process. To regenerate hydrogen the oxygen reduction process of a metal oxide at high temperatures (1000–2500 °C) is generally required. In this study to overcome the problem of an energy efficiency imbalance in which the required energy of the oxygen reduction process for hydrogen regeneration is higher than the generated hydrogen energy we investigated the possibility of the oxygen reduction of a metal oxide with a low energy using microwave irradiation. For this purpose a macroporous nickel-oxide structure was used as a metal oxide catalyst to generate hydrogen gas and the oxidized surface of the macroporous nickel-oxide structure could be reduced by microwave irradiation. Through this oxidation reduction process ∼750 μmol g−1 of hydrogen gas could be continuously regenerated. In this way it is expected that oxygen-enriched metal oxide materials can be efficiently reduced by microwave irradiation with a low power consumption of <∼4% compared to conventional high-temperature heat treatment and thus can be used for efficient hydrogen generation and regeneration processes in the future.
Hydrogen Fueling Standardization: Enabling ZEVs with "Same as Today" Fueling and FCEV Range and Safety
Oct 2015
Publication
Zero Emission Vehicles (ZEVs) are necessary to help reduce the emissions in the transportation sector which is responsible for 40% of overall greenhouse gas emissions. There are two types of ZEVs Battery Electric Vehicles (BEVs) and Fuel Cell Electric Vehicles (FCEVs) Commercial Success of BEVs has been challenging thus far also due to limited range and very long charging duration. FCEVs using H2 infrastructure with SAE J2601 and J2799 standards can be consistently fuelled in a safe manner fast and resulting in a range similar to conventional vehicles. Specifically fuelling with SAE J2601 with the SAE J2799 enables FCEVs to fill with hydrogen in 3-5 minutes and to achieve a high State of Charge (SOC) resulting in 300+ mile range without exceeding the safety storage limits. Standardized H2 therefore gives an advantage to the customer over electric charging. SAE created this H2 fuelling protocol based on modelling laboratory and field tests. These SAE standards enable the first generation of commercial FCEVs and H2 stations to achieve a customer acceptable fueling similar to today's experience. This report details the advantages of hydrogen and the validation of H2 fuelling for the SAE standards.
The Analysis of Fire Test for the High Pressure Composite Cylinder
Sep 2011
Publication
A large number of natural gas vehicles (NGV) with composite cylinders run in the world. In order to store hydrogen using the composite cylinder has also reached commercialization for the hydrogen fuel cell vehicle (FCV) which is been developing on ECO Energy. Under these increasing circumstances the most important issue is that makes sure of safety of the hydrogen composite cylinder. In case of the composite cylinder a standards to verify the safety of cylinders obey several country's standards. For NGV ISO 11439 has adopted as international standards but for FCV it has been still developing and there is only ISO/TS 15869 as international technical standards. In contents of international standards the fire test is the weakest part. The fire test is that the pressure relief valves (PRD) normally operate or not in order to prevent cylinders bursting when a vehicle is covered by fire. However with present standards there is no method to check the problem from vehicles in local flame. This study includes fire test results that have been performed to establish the fire-test standards.
Assessment of Safety for Hydrogen Fuel Cell Vehicle
Sep 2011
Publication
A prospective global market share of Electric vehicle (EV) Hybrid electric vehicle (HEV) and Hydrogen Fuel Cell Vehicle (HFCV) is expected to grow due to stringent emission regulation and oil depletion. However it is essential to secure protection against high-pressure hydrogen gas and high-voltage in fuel cell vehicles and thus needs to develop a technique for safety assessment of HFCV. In this experiment 8 research institutes including the Korea Automobile Testing and Research Institute Hyundai Motor Company took part in. This project was supported by the Ministry of Land Transportation and Maritime Affairs of the Republic of Korea.
Numerical Investigation of the Initial Charging Process of the Liquid Hydrogen Tank for Vehicles
Dec 2022
Publication
Liquid hydrogen has been studied for use in vehicles. However during the charging process liquid hydrogen is lost as gas. Therefore it is necessary to estimate and reduce this loss and simulate the charging process. In this study the initial charging process of a vehicle liquid hydrogen tank under room temperature and atmospheric pressure conditions was numerically investigated. A transient thermal-fluid simulation with a phase-change model was performed to analyze variations in the volume pressure mass flow rate and temperature. The results showed that the process could be divided into three stages. In the first stage liquid hydrogen was actively vaporized at the inner wall surface of the storage tank. The pressure increased rapidly and liquid droplets were discharged into the vent pipe during the second stage. In the third stage the mass flow rates of liquid and hydrogen gas at the outlet showed significant fluctuations owing to complex momentum generated by the evaporation and charging flow. The temperatures of the inner and outer walls and insulation layer decreased significantly slower than that of the gas region because of its high heat capacity and insulation effect. The optimal structure should be further studied because the vortex stagnation and non-uniform cooling of the wall occurred near the inlet and outlet pipes.
The Study on the Internal Temperature Change of Type 3 and Type 4 Composite Cylinder During Filling
Sep 2013
Publication
The number of eco friendly vehicle which is using green energy such as natural gas(NG) and hydrogen(H2) is rapidly increasing in the world. Almost all of the car manufacturers are adopting the pressurizing fuel method to storage gas. The fuel storage system which can pressurize the fuel as high as possible is necessary to maximize the mileage of the vehicle. In Korea the most important issue is that makes sure of safety of the fuel storage system and several tests are performed to verify safety of the composite cylinder especially for Type 3 and Type 4. In this research an empirical study on the internal temperature change of Type 3 and Type 4 composite cylinder during filling is performed by gas cycling test equipment. In order to measure the temperature totally twelve sensors(every four sensors on the top middle and bottom) are installed in each cylinder. As a consequence large amount of compression heat is generated during rapid filling and the result temperature change in Type 4 is greater than Type 3 is confirmed depending on property of the liner material such as thermal conduction and thickness of carbon composite.
Numerical Analysis of the Effects of Ship Motion on Hydrogen Release and Dispersion in an Enclosed Area
Jan 2022
Publication
Hydrogen is an alternative to conventional heavy marine fuel oil following the initial strategy of the International Maritime Organization (IMO) for reducing greenhouse gas emissions. Although hydrogen energy has many advantages (zero-emission high efficiency and low noise) it has considerable fire and explosion risks due to its thermal and chemical characteristics (wide flammable concentration range and low ignition energy). Thus safety is a key concern related to the use of hydrogen. Whereas most previous studies focused on the terrestrial environment we aim to analyze the effects of the ship’s motion on hydrogen dispersion (using commercial FLUENT code) in an enclosed area. When compared to the steady state our results revealed that hydrogen reached specific sensors in 63% and 52% less time depending on vessel motion type and direction. Since ships carry and use a large amount of hydrogen as a power source the risk of hydrogen leakage from collision or damage necessitates studying the correspondence between leakage diffusion and motion characteristics of the ship to position the sensor correctly.
Synthesis of Spherical V-Nb-Mo-Ta-W High-Entropy Alloy Powder Using Hydrogen Embrittlement and Spheroidization by Thermal Plasma
Dec 2019
Publication
V-Nb-Mo-Ta-W high-entropy alloy (HEA) one of the refractory HEAs is considered as a next-generation structural material for ultra-high temperature uses. Refractory HEAs have low castability and machinability due to their high melting temperature and low thermal conductivity. Thus powder metallurgy becomes a promising method for fabricating components with refractory HEAs. Therefore in this study we fabricated spherical V-Nb-Mo-Ta-W HEA powder using hydrogen embrittlement and spheroidization by thermal plasma. The HEA ingot was prepared by vacuum arc melting and revealed to have a single body-centered cubic phase. Hydrogen embrittlement which could be achieved by annealing in a hydrogen atmosphere was introduced to get the ingot pulverized easily to a fine powder having an angular shape. Then the powder was annealed in a vacuum atmosphere to eliminate the hydrogen from the hydrogenated HEA resulting in a decrease in the hydrogen concentration from 0.1033 wt% to 0.0003 wt%. The angular shape of the HEA powder was turned into a spherical one by inductively-coupled thermal plasma allowing to fabricate spherical V-Nb-Mo-Ta-W HEA powder with a d50 value of 28.0 μm.
Study on the Explosion of the Hydrogen Fuel Tank of Fuel Cell Electric Vehicles in Semi-Enclosed Spaces
Dec 2022
Publication
The rise in hydrogen fuel cell electric vehicles (FCEVs) is expected to pose a variety of hazards on the road. Vehicles using hydrogen could cause significant damage owing to hydrogen vapor cloud explosions jet fires caused by leakage or hydrogen tank explosions. This risk is expected to further increase in semi-enclosed spaces such as underground parking lots and road tunnels. Therefore it is necessary to study the fire safety of hydrogen vehicles in semi-enclosed spaces. In this study an experiment on hydrogen tank explosion was performed. In addition the CFD numerical model was verified using the experimental results and the damaging effect due to pressure propagation during hydrogen tank explosions in underground parking lots and road tunnels was analyzed using numerical analysis. From the experiment results the hydrogen tank exploded at about 80 Mpa a maximum incident pressure is generated 267 kPa at a distance of 1.9 m. As a result of numerical analysis based on the experimental results the limit distance that can cause serious injury due to the explosion of a hydrogen tank in a road tunnel or underground parking lot was analyzed up to about 20 m from the point of explosion.
Explosion Characteristics of Hydrogen Gas in Varying Ship Ventilation Tunnel Geometries: An Experimental Study
Apr 2022
Publication
Hydrogen is widely regarded as a key element of prospective energy solutions for alleviating environmental emission problems. However hydrogen is classified as a high-risk gas because of its wide explosive range high overpressure low ignition energy and fast flame propagation speed compared with those of hydrocarbon-based gases. In addition deflagration can develop into detonation in ventilation or explosion guide tunnels if explosion overpressure occurs leading to the explosion of all combustible gases. However quantitative evidence of an increase in the explosion overpressure of ventilation tunnels is unavailable because the explosive characteristics of hydrogen gas are insufficiently understood. Therefore this study investigated an explosion chamber with the shape of a ventilation pipe in a ship compartment. The effect of tunnel length on explosion overpressure was examined experimentally. For quantitative verification the size of the hydrogen gas explosion overpressure was analyzed and compared with experimental values of hydrocarbon-based combustible gases (butane and LPG (propane 98%)). The experimental database can be used for explosion risk analyses of ships when designing ventilation holes and piping systems and developing new safety guidelines for hydrogen carriers and hydrogen-fueled ships.
A Comparative Feasibility Study of the Use of Hydrogen Produced from Surplus Wind Power for a Gas Turbine Combined Cycle Power Plant
Dec 2021
Publication
Because of the increasing challenges raised by climate change power generation from renewable energy sources is steadily increasing to reduce greenhouse gas emissions especially CO2 . However this has escalated concerns about the instability of the power grid and surplus power generated because of the intermittent power output of renewable energy. To resolve these issues this study investigates two technical options that integrate a power-to-gas (PtG) process using surplus wind power and the gas turbine combined cycle (GTCC). In the first option hydrogen produced using a power-to-hydrogen (PtH) process is directly used as fuel for the GTCC. In the second hydrogen from the PtH process is converted into synthetic natural gas by capturing carbon dioxide from the GTCC exhaust which is used as fuel for the GTCC. An annual operational analysis of a 420-MWclass GTCC was conducted which shows that the CO2 emissions of the GTCC-PtH and GTCC-PtM plants could be reduced by 95.5% and 89.7% respectively in comparison to a conventional GTCC plant. An economic analysis was performed to evaluate the economic feasibility of the two plants using the projected cost data for the year 2030 which showed that the GTCC-PtH would be a more viable option.
Temperature Change of a Type IV Cylinder During Hydrogen Fuelling Process
Sep 2009
Publication
The temperature of the hydrogen cylinder needs to be carefully controlled during fuelling process. The maximum temperature should be less than 85℃ according to the ISO draft code. If the fuelling period is reduced the maximum temperature should increase. In this study temperature change of a Type IV cylinder was measured during the hydrogen fuelling process up to 35 MPa. Fuelling period was 3 to 5 minutes. Twelve thermocouples were installed to measure inside gas temperature and seven were attached on the outside of the cylinder. An infrared camera was also used for measuring temperature distribution of outside of cylinder. The maximum gas temperature was higher than 85℃ inside of the cylinder. Significant temperature difference between the upper and lower part of the vessel was observed. Temperature near the plug and the valve was quickly increased and maintained higher than that of the other region. Temperature increases for the partial refuelling process were also discussed.
Strategy for Selecting an Optimal Propulsion System of a Liquefied Hydrogen Tanker
Jan 2017
Publication
This study proposed a strategy for selecting an optimal propulsion system of a liquefied hydrogen tanker. Four propulsion system options were conceivable depending on whether the hydrogen BOG (boil-off gas) from the cryogenic cargo tanks was used for fuel or not. These options were evaluated in terms of their economic technological and environmental feasibilities. The comparison scope included not only main machinery but also the BOG handling system with electric generators. Cost-benefit analysis life-cycle costing including carbon tax and an energy efficiency design index were used as measures to compare the four alternative systems. The analytic hierarchy process made scientific decision-making possible. This methodology provided the priority of each attribute through the use of pairwise comparison matrices. Consequently the propulsion system using LNG with hydrogen BOG recovery was determined to be the optimal alternative. This system was appropriate for the tanker that achieved the highest evaluation score.
Recent Progress Using Solid-State Materials for Hydrogen Storage: A Short Review
Feb 2022
Publication
With the rapid growth in demand for effective and renewable energy the hydrogen era has begun. To meet commercial requirements efficient hydrogen storage techniques are required. So far four techniques have been suggested for hydrogen storage: compressed storage hydrogen liquefaction chemical absorption and physical adsorption. Currently high-pressure compressed tanks are used in the industry; however certain limitations such as high costs safety concerns undesirable amounts of occupied space and low storage capacities are still challenges. Physical hydrogen adsorption is one of the most promising techniques; it uses porous adsorbents which have material benefits such as low costs high storage densities and fast charging–discharging kinetics. During adsorption on material surfaces hydrogen molecules weakly adsorb at the surface of adsorbents via long-range dispersion forces. The largest challenge in the hydrogen era is the development of progressive materials for efficient hydrogen storage. In designing efficient adsorbents understanding interfacial interactions between hydrogen molecules and porous material surfaces is important. In this review we briefly summarize a hydrogen storage technique based on US DOE classifications and examine hydrogen storage targets for feasible commercialization. We also address recent trends in the development of hydrogen storage materials. Lastly we propose spillover mechanisms for efficient hydrogen storage using solid-state adsorbents.
Layered Transition Metal Selenophosphites for Visible Light Photoelectrochemical Production of Hydrogen
Jun 2021
Publication
The growing consumption of global energy has posed serious challenges to environmental protection and energy supplies. A promising solution is via introducing clean and sustainable energy sources including photoelectrochemical hydrogen fuel production. 2D materials such as transition metal trichalcogenphosphites (MPCh3) are gaining more and more interest for their potential as photocatalysts. Crystals of transition metal selenophosphites namely MnPSe3 FePSe3 and ZnPSe3 were tested as photocatalysts for the hydrogen evolution reaction (HER). ZnPSe3 is the one that exhibited the lowest overpotential and the higher response to the light during photocurrent experiments in acidic media. For this reason among the crystals in this work it is the most promising for the photocatalyzed production of hydrogen.
Non-precious Electrocatalysts for Oxygen Evolution Reaction in Anion Exchange Membrane Water Electrolysis: A Mini Review
Sep 2021
Publication
Anion exchange membrane water electrolysis (AEMWE) is considered the next generation of green hydrogen production method because it uses low-cost non-noble metal oxide electrocatalyst electrodes and can store highpurity hydrogen under high pressure. However the commercialization of AEMWE with non-precious metal oxide electrocatalysts is challenging due to low electrocatalytic activity and durability. Overcoming the low kinetics caused by four-electron transfer is vital in addressing the low activity of non-noble metal oxide electrocatalysts for oxygen evolution reaction. This article overviews the synthesis methods and related techniques for various anode electrodes applied to AEMWE systems. We highlight effective strategies that have been developed to improve the performance and durability of the non-precious electrocatalysts and ensure the stable operation of AEMWE followed by a critical perspective to encourage the development of this technology.
The Enhanced Hydrogen Storage Capacity of Carbon Fibers The Effect of Hollow Porous Structure and Surface Modification
Jul 2021
Publication
In this study highly porous carbon fiber was prepared for hydrogen storage. Porous carbon fiber (PCF) and activated porous carbon fiber (APCF) were derived by carbonization and chemical activation after selectively removing polyvinyl alcohol from a bi-component fiber composed of polyvinyl alcohol and polyacrylonitrile (PAN). The chemical activation created more pores on the surface of the PCF and consequently highly porous APCF was obtained with an improved BET surface area (3058 m2 g−1) and micropore volume (1.18 cm3 g−1) compare to those of the carbon fiber which was prepared by calcination of monocomponent PAN. APCF was revealed to be very efficient for hydrogen storage its hydrogen capacity of 5.14 wt% at 77 K and 10 MPa. Such hydrogen storage capacity is much higher than that of activated carbon fibers reported previously. To further enhance hydrogen storage capacity catalytic Pd nanoparticles were deposited on the surface of the APCF. The Pd-deposited APCF exhibits a high hydrogen storage capacity of 5.45 wt% at 77 K and 10 MPa. The results demonstrate the potential of Pd-deposited APCF for efficient hydrogen storage.
Highly Selective Porous Separator with Thin Skin Layer for Alkaline Water Electrolysis
Feb 2022
Publication
Advanced porous separators with thin selective skin layers to reduce the hydrogen permeation are developed for applications in alkaline water electrolysis. A thin skin layer based on crosslinked polyvinyl alcohol (cPVA) is fabricated on a porous substrate by a facile and scalable ultrasonic spray coating process. As the number of ultrasonic spraying cycles increases the resulting separator demonstrates a decrease in the large-diameter pore fraction an increase in the bubble-point pressure and a reduction in the hydrogen permeability without a significant increase in the areal resistance. As a result the optimized separator with a cPVA skin layer combines a low ionic resistance of 0.267 Ω cm2 a high bubble point pressure of 2.71 bar and a low hydrogen permeability of 1.12 × 10− 11 mol cm− 2 s − 1 bar− 1 . The electrolytic cell assembled with cPVAZ-30 achieves current densities of 861 mA cm− 2 and 1890 mA cm− 2 at 2.0 V and 2.6 V respectively in a 30 wt% KOH electrolyte solution at 80 ◦C.
Numerical Analysis for Hydrogen Flame Acceleration during a Severe Accident Initiated by SBLOCA in the APR1400 Containment
Jan 2022
Publication
We performed a hydrogen combustion analysis in the Advanced Power Reactor 1400 MWe (APR1400) containment during a severe accident initiated by a small break loss of coolant accident (SBLOCA) which occurred at a lower part of the cold leg using a multi-dimensional hydrogen analysis system (MHAS) to confirm the integrity of the APR1400 containment. The MHAS was developed by combining MAAP GASFLOW and COM3D to simulate hydrogen release distribution and combustion in the containment of a nuclear power plant during the severe accidents in the containment of a nuclear power reactor. The calculated peak pressure due to the flame acceleration by the COM3D using the GASFLOW results as an initial condition of the hydrogen distribution was approximately 555 kPa which is lower than the fracture pressure 1223 kPa of the APR1400 containment. To induce a higher peak pressure resulted from a strong flame acceleration in the containment we intentionally assumed several things in developing an accident scenario of the SBLOCA. Therefore we may judge that the integrity of the APR1400 containment can be maintained even though the hydrogen combustion occurs during the severe accident initiated by the SBLOCA.
Simulator Development of Virtual Experience and Accident Scenarios of Hydrogen Stations for Safety
Sep 2007
Publication
Nowadays 4 type hydrogen stations have been demonstrated in Korea for preparing hydrogen economy. This simulator is consists of virtual experience modules and virtual accident scenarios of 4 type hydrogen stations. Virtual experience modules show the performance properties through a movie or a virtual reality technology. Also they provide an explanation of hydrogen station equipment and a guide for operators immediately after the accident. Virtual accident scenario modules show accident simulations based on modelling equations as 3D virtual reality. These modules could choose the sham accident for every kind of a station after categorizing all possible accidents in a station A Commercialized CFD program based on hydrogen dispersion model theory shows a movie of accident simulations. The result of a simulator has been developed as web applications. And will be applied to training materials and public relations for a user concerned about hydrogen stations.
Compatibility and Suitability of Existing Steel Pipelines for Transport of Hydrogen and Hydrogen-natural Gas Blends
Sep 2017
Publication
Hydrogen is being considered as a pathway to decarbonize large energy systems and for utility-scale energy storage. As these applications grow transportation infrastructure that can accommodate large quantities of hydrogen will be needed. Many millions of tons of hydrogen are already consumed annually some of which is transported in dedicated hydrogen pipelines. The materials and operation of these hydrogen pipeline systems however are managed with more constraints than a conventional natural gas pipeline. Transitional strategies for deep decarbonization of energy systems include blending hydrogen into existing natural gas systems where the materials and operations may not have the same controls. This study explores the hydrogen compatibility of existing pipeline steels and the suitability of these steels in hydrogen pipeline systems. Representative fracture and fatigue properties of pipeline grade steels in gaseous hydrogen are summarized from the literature. These properties are then considered in idealized design life calculations to inform materials performance for a typical gas pipeline.
Low-carbon Energy Transition With the Sun and Forest: Solar-driven Hydrogen Production from Biomass
Nov 2021
Publication
There is a need to derive hydrogen from renewable sources and the innovative stewardship of two natural resources namely the Sun and forest could provide a new pathway. This paper provides the first comparative analysis of solar-driven hydrogen production from environmental angles. A novel hydrogen production process proposed in this paper named Solar-Driven Advanced Biomass Indirect-Gasification (SABI-Hydrogen) shows promise toward achieving continuous operation and scalability the two key challenges to meet future energy needs. The calculated Global Warming Potential for 1 kg of solar-driven hydrogen production is 1.04 kg CO2-eq/kg H2 less than half of the current biomass gasification process which emits 2.67 kg CO2-eq/kg H2. Further SABI-Hydrogen demonstrates the least-carbon intensive pathway among all current hydrogen production methods. Thus solar-driven hydrogen production from biomass could lead to a sustainable supply essential for a low-carbon energy transition.
Exploring Future Promising Technologies in Hydrogen Fuel Cell Transportation
Jan 2022
Publication
The purpose of this research was to derive promising technologies for the transport of hydrogen fuel cells thereby supporting the development of research and development policy and presenting directions for investment. We also provide researchers with information about technology that will lead the technology field in the future. Hydrogen energy as the core of carbon neutral and green energy is a major issue in changing the future industrial structure and national competitive advantage. In this study we derived promising technology at the core of future hydrogen fuel cell transportation using the published US patent and paper databases (DB). We first performed text mining and data preprocessing and then discovered promising technologies through generative topographic mapping analysis. We analyzed both the patent DB and treatise DB in parallel and compared the results. As a result two promising technologies were derived from the patent DB analysis and five were derived from the paper DB analysis.
A Numerical Simulation of Hydrogen Diffusion for the Hydrogen Leakage from a Fuel Cell Vehicle in an Underground Parking Garage
Sep 2011
Publication
In the present study the diffusion process of hydrogen leaking from a FCV (Fuel Cell Vehicle) in an underground parking garage is analyzed by numerical simulations in order to assess the risk of a leakage accident. The temporal and spatial evolution of the hydrogen concentration as well as the flammable region in the parking garage was predicted numerically. The effects of the leakage flow rate and an additional ventilation fan were investigated to evaluate the ventilation performance to relieve the accumulation of the hydrogen gas. The volume of the flammable region shows a non-linear growth in time and rapidly increases eventually. The present numerical analysis can provide a physical insight and quantitative data for safety of various hydrogen applications.
Preference Structure on the Design of Hydrogen Refueling Stations to Activate Energy Transition
Aug 2020
Publication
As a countermeasure to the greenhouse gas problem the world is focusing on alternative fuel vehicles (AFVs). The most prominent alternatives are battery electric vehicles (BEV) and fuel cell electric vehicles (FCEVs). This study examines FCEVs especially considering hydrogen refueling stations to fill the gap in the research. Many studies suggest the important impact that infrastructure has on the diffusion of AFVs but they do not provide quantitative preferences for the design of hydrogen refueling stations. This study analyzes and presents a consumer preference structure for hydrogen refueling stations considering the production method distance probability of failure to refuel number of dispensers and fuel costs as core attributes. For the analysis stated preference data are applied to choice experiments and mixed logit is used for the estimation. Results indicate that the supply stability of hydrogen refueling stations is the second most important attribute following fuel price. Consumers are willing to pay more for green hydrogen compared to gray hydrogen which is hydrogen produced by fossil fuels. Driver fuel type and perception of hydrogen energy influence structure preference. Our results suggest a specific design for hydrogen refueling stations based on the characteristics of user groups.
Potential Liquid-Organic Hydrogen Carrier (LOHC) Systems: A Review on Recent Progress
Nov 2020
Publication
The depletion of fossil fuels and rising global warming challenges encourage to find safe and viable energy storage and delivery technologies. Hydrogen is a clean efficient energy carrier in various mobile fuel-cell applications and owned no adverse effects on the environment and human health. However hydrogen storage is considered a bottleneck problem for the progress of the hydrogen economy. Liquid-organic hydrogen carriers (LOHCs) are organic substances in liquid or semi-solid states that store hydrogen by catalytic hydrogenation and dehydrogenation processes over multiple cycles and may support a future hydrogen economy. Remarkably hydrogen storage in LOHC systems has attracted dramatically more attention than conventional storage systems such as high-pressure compression liquefaction and absorption/adsorption techniques. Potential LOHC media must provide fully reversible hydrogen storage via catalytic processes thermal stability low melting points favorable hydrogenation thermodynamics and kinetics large-scale availability and compatibility with current fuel energy infrastructure to practically employ these molecules in various applications. In this review we present various considerable aspects for the development of ideal LOHC systems. We highlight the recent progress of LOHC candidates and their catalytic approach as well as briefly discuss the theoretical insights for understanding the reaction mechanism.
Novel Carbon-neutral Hydrogen Production Process of Steam Methane Reforming Integrated with Desalination Wastewater-based CO2 Utilization
Nov 2022
Publication
Steam methane reforming (SMR) process is facing serious greenhouse effect problems because of the significant CO2 emissions. To reduce pollution caused by gaseous emissions desalination wastewater can be used because it contains highly concentrated useful mineral ions such as Ca2+ Mg2+ and Na+ which react with carbonate ions. This study proposes a novel SMR process for carbon-neutral hydrogen production integrated with desalination wastewater-based CO2 utilization. A process model for the design of a novel SMR process is proposed; it comprises the following steps: (1) SMR process for hydrogen production; and (2) desalination wastewater recovery for CO2 utilization. In the process model the CO2 from the SMR process was captured using the Na+ ion and the captured ionic CO2 was carbonated using the Ca2+ and Mg2+ ions in desalination wastewater. The levelized cost of hydrogen (LCOH) was assessed to demonstrate the economic feasibility of the proposed process. Therefore 94.5 % of the CO2 from the SMR process was captured and the conversion of MgCO3 and CaCO3 was determined to be 60 % and 99 % respectively. In addition the CO2 emission via the proposed process was determined to be 0.016 kgCO2/kgH2 and the LCOH was calculated to be 2.6 USD/kgH2.
Recent Developments in State-of-the-art Hydrogen Energy Technologies – Review of Hydrogen Storage Materials
Jan 2023
Publication
Hydrogen energy has been assessed as a clean and renewable energy source for future energy demand. For harnessing hydrogen energy to its fullest potential storage is a key parameter. It is well known that important hydrogen storage characteristics are operating pressure-temperature of hydrogen hydrogen storage capacity hydrogen absorption-desorption kinetics and heat transfer in the hydride bed. Each application needs specific properties. Every class of hydrogen storage materials has a different set of hydrogenation characteristics. Hence it is required to understand the properties of all hydrogen storage materials. The present review is focused on the state-of– the–art hydrogen storage materials including metal hydrides magnesium-based materials complex hydride systems carbonaceous materials metal organic frameworks perovskites and materials and processes based on artificial intelligence. In each category of materials‘ discovery hydrogen storage mechanism and reaction crystal structure and recent progress have been discussed in detail. Together with the fundamental synthesis process latest techniques of material tailoring like nanostructuring nanoconfinement catalyzing alloying and functionalization have also been discussed. Hydrogen energy research has a promising potential to replace fossil fuels from energy uses especially from automobile sector. In this context efforts initiated worldwide for clean hydrogen production and its use via fuel cell in vehicles is much awaiting steps towards sustainable energy demand.
Photocatalytic Water Splitting: How Far Away Are We from Being Able to Industrially Produce Solar Hydrogen?
Oct 2022
Publication
Solar water splitting (SWS) has been researched for about five decades but despite successes there has not been a big breakthrough advancement. While the three fundamental steps light absorption charge carrier separation and diffusion and charge utilization at redox sites are given a great deal of attention either separately or simultaneously practical considerations that can help to increase efficiency are rarely discussed or put into practice. Nevertheless it is possible to increase the generation of solar hydrogen by making a few little but important adjustments. In this review we talk about various methods for photocatalytic water splitting that have been documented in the literature and importance of the thin film approach to move closer to the large-scale photocatalytic hydrogen production. For instance when comparing the film form of the identical catalyst to the particulate form it was found that the solar hydrogen production increased by up to two orders of magnitude. The major topic of this review with thin-film forms is discussion on several methods of increased hydrogen generation under direct solar and one-sun circumstances. The advantages and disadvantages of thin film and particle technologies are extensively discussed. In the current assessment potential approaches and scalable success factors are also covered. As demonstrated by a film-based approach the local charge utilization at a zero applied potential is an appealing characteristic for SWS. Furthermore we compare the PEC-WS and SWS for solar hydrogen generation and discuss how far we are from producing solar hydrogen on an industrial scale. We believe that the currently employed variety of attempts may be condensed to fewer strategies such as film-based evaluation which will create a path to address the SWS issue and achieve sustainable solar hydrogen generation.
Simulation of a Hydrogen-Air Diffusion Flame under Consideration of Component-Specific Diffusivities
Mar 2022
Publication
This work deals with the numerical investigation of a three-dimensional laminar hydrogenair diffusion flame in which a cylindrical fuel jet is surrounded by in-flowing air. To calculate the distribution of gas molecules the model solves the species conservation equation for N-1 components using infinity fast chemistry and irreversible chemical reaction. The consideration of the component-specific diffusion has a strong influence on the position of the high-temperature zone as well as on the concentration distribution of the individual gas molecules. The calculations of the developed model predict the radial and axial species and temperature distribution in the combustion chamber comparable to those from previous publications. Deviations due to a changed burner geometry and air supply narrow the flame structure by up to 50% and the high-temperature zones merge toward the central axis. Due to the reduced inflow velocity of the hydrogen the high-temperature zones develop closer to the nozzle inlet of the combustion chamber. As the power increases the length of the cold hydrogen jet increases. Furthermore the results show that the axial profiles of temperature and mass fractions scale quantitatively with the power input by the fuel.
Prioritization and Optimal Location of Hydrogen Fueling Stations in Seoul: Using Multi-Standard Decision-Making and ILP Optimization
Mar 2023
Publication
Thus far the adoption of hydrogen fuel cell vehicles (HCEVs) has been hampered by the lack of hydrogen fueling infrastructure. This study aimed to determine the optimal location and prioritization of hydrogen fueling stations (HFSs) in Seoul by utilizing a multi-standard decision making approach and optimization method. HFS candidate sites were evaluated with respect to relevant laws and regulations. Key factors such as safety economy convenience and demand for HCEVs were considered. Data were obtained through a survey of experts in the fields of HCEV and fuel cells and the Analytic Hierarchy Process method was applied to prioritize candidate sites. The optimal quantity and placement of HFSs was then obtained using optimization software based on the acceptable travel time from intersections of popular roads in Seoul. Our findings suggest that compliance with legal safety regulations is the most important factor when constructing HFSs. Furthermore sensitivity analysis revealed that the hydrogen supply cost currently holds the same weight as other elements. The study highlights the importance of utilizing a multi-standard decision-making approach and optimization methods when determining the optimal location and prioritization of HFSs and can help develop a systematic plan for the nationwide construction of HFSs in South Korea.
Economic Analysis of P2G Green Hydrogen Generated by Existing Wind Turbines on Jeju Island
Dec 2022
Publication
Every wind turbine is subject to fluctuations in power generation depending on climatic conditions. When electricity supply exceeds demand wind turbines are forced to implement curtailment causing a reduction in generation efficiency and commercial loss to turbine owners. Since the frequency and amount of curtailment of wind turbines increases as the amount of renewable energy become higher on Jeju Island in South Korea Jeju is configuring a Power to Gas (P2G) water electrolysis system that will be connected to an existing wind farm to use the “wasted energy”. In this study economic analysis was performed by calculating the production cost of green hydrogen and sensitivity analysis evaluated the variance in hydrogen cost depending on several influential factors. Approaches to lower hydrogen costs are necessary for the following reasons. The operating company needs a periodical update of hydrogen sale prices by reflecting a change in the system margin price (SMP) with the highest sensitivity to hydrogen cost. Technical development to reduce hydrogen costs in order to reduce power consumption for producing hydrogen and a decrease in annual reduction rate for the efficiency of water electrolysis is recommended. Discussions and research regarding government policy can be followed to lower the hydrogen cost.
Estimation of the Levelized Cost of Nuclear Hydrogen Production from Light Water Reactors in the United States
Aug 2022
Publication
In June 2021 the United States (US) Department of Energy (DOE) hosted the first-ever Hydrogen Shot Summit which lasted for two days. More than 3000 stockholders around the world were convened at the summit to discuss how low-cost clean hydrogen production would be a huge step towards solving climate change. Hydrogen is a dynamic fuel that can be used across all industrial sectors to lower the carbon intensity. By 2030 the summit hopes to have developed a means to reduce the current cost of clean hydrogen by 80%; i.e. to USD 1 per kilogram. Because of the importance of clean hydrogen towards carbon neutrality the overall DOE budget for Fiscal Year 2021 is USD 35.4 billion and the total budget for DOE hydrogen activities in Fiscal Year 2021 is USD 285 million representing 0.81% of the total DOE budget for 2021. The DOE hydrogen budget of 2021 is estimated to increase to USD 400 million in Fiscal Year 2022. The global hydrogen market is growing and the US is playing an active role in ensuring its growth. Depending on the electricity source used the electrolysis of hydrogen can have no greenhouse gas emissions. When assessing the advantages and economic viability of hydrogen production by electrolysis it is important to take into account the source of the necessary electricity as well as emissions resulting from electricity generation. In this study to evaluate the levelized cost of nuclear hydrogen production the International Atomic Energy Agency Hydrogen Economic Evaluation Program is used to model four types of LWRs: Exelon’s Nine Mile Point Nuclear Power Plant (NPP) in New York; Palo Verde NPP in Arizona; Davis-Besse NPP in Ohio; and Prairie Island NPP in Minnesota. Each of these LWRs has a different method of hydrogen production. The results show that the total cost of hydrogen production for Exelon’s Nine Mile Point NPP Palo Verde NPP Davis-Besse NPP and Prairie Island NPP was 4.85 ± 0.66 4.77 ± 1.36 3.09 ± 1.19 and 0.69 ± 0.03 USD/kg respectively. These findings show that among the nuclear reactors the cost of nuclear hydrogen production using Exelon’s Nine Mile Point NPP reactor is the highest whereas the cost of nuclear hydrogen production using the Prairie Island NPP reactor is the lowest.
Graded Grain Structure to Improve Hydrogen-Embrittlement Resistance of TWIP Steel
Nov 2020
Publication
The high strength of twinning-induced plasticity (TWIP) steels makes them vulnerable to the hydrogen embrittlement (HE) phenomenon thereby limiting their potential applications. This study suggests inducing a graded grain structure (GGS) in a Fe-17Mn-0.8C TWIP steel through shot peening and subsequent heat treatment to solve the problem. The microstructures and fracture surfaces of GGS TWIP steel were compared with those of conventionally manufactured TWIP steel possessing a uniform grain structure (UGS). Compared with the conventional UGS TWIP steel GGS steel showed similar tensile properties with a yield strength of 310 MPa tensile strength of 1060 MPa and elongation-to-failure of 135%. It also exhibited moderately enhanced low-cycle fatigue (LCF) resistance in terms of fatigue life (8196 cycles to failure) compared with the UGS steel (7201 cycles). Furthermore GGS TWIP steel exhibited a marked improvement in HE resistance both in the monotonic (by a slow-strain-rate test) and cyclic deformation modes (by the LCF test) in a hydrogen environment. A relatively fine-grained (d = 15.6 μm) surficial area enhanced the HE resistance by inhibiting hydrogen penetration and decreasing twin density while the coarse-grained (d = 74.6 μm) interior promoted the LCF resistance by suppressing crack growth
Materials for Hydrogen-based Energy Storage - Past, Recent Progress and Future Outlook
Dec 2019
Publication
Michael Hirscher,
Volodymyr A. Yartys,
Marcello Baricco,
José Bellosta von Colbe,
Didier Blanchard,
Robert C. Bowman Jr.,
Darren P. Broom,
Craig Buckley,
Fei Chang,
Ping Chen,
Young Whan Cho,
Jean-Claude Crivello,
Fermin Cuevas,
William I. F. David,
Petra E. de Jongh,
Roman V. Denys,
Martin Dornheim,
Michael Felderhoff,
Yaroslav Filinchuk,
George E. Froudakis,
David M. Grant,
Evan MacA. Gray,
Bjørn Christian Hauback,
Teng He,
Terry D. Humphries,
Torben R. Jensen,
Sangryun Kim,
Yoshitsugu Kojima,
Michel Latroche,
Hai-wen Li,
Mykhaylo V. Lototskyy,
Joshua W. Makepeace,
Kasper T. Møller,
Lubna Naheed,
Peter Ngene,
Dag Noreus,
Magnus Moe Nygård,
Shin-ichi Orimo,
Mark Paskevicius,
Luca Pasquini,
Dorthe B. Ravnsbæk,
M. Veronica Sofianos,
Terrence J. Udovic,
Tejs Vegge,
Gavin Walker,
Colin Webb,
Claudia Weidenthaler and
Claudia Zlotea
Globally the accelerating use of renewable energy sources enabled by increased efficiencies and reduced costs and driven by the need to mitigate the effects of climate change has significantly increased research in the areas of renewable energy production storage distribution and end-use. Central to this discussion is the use of hydrogen as a clean efficient energy vector for energy storage. This review by experts of Task 32 “Hydrogen-based Energy Storage” of the International Energy Agency Hydrogen TCP reports on the development over the last 6 years of hydrogen storage materials methods and techniques including electrochemical and thermal storage systems. An overview is given on the background to the various methods the current state of development and the future prospects. The following areas are covered; porous materials liquid hydrogen carriers complex hydrides intermetallic hydrides electro-chemical storage of energy thermal energy storage hydrogen energy systems and an outlook is presented for future prospects and research on hydrogen-based energy storage
Volumetric Analysis Technique for Analyzing the Transport Properties of Hydrogen Gas in Cylindrical-shaped Rubbery Polymers
Mar 2021
Publication
We report volumetric analysis techniques to analyze the transport properties of hydrogen dissolved in cylindrical-shaped polymers. The techniques utilize the volume measurement of the released hydrogen from rubber by gas collection in a graduated cylinder after charging sample with high-pressure hydrogen and subsequent decompression. We further improve the graduated cylinder with some modifications such as reading the electrical capacitance of the water level using electrodes and changing the sample loading position. From the measurement results the uptake (C∞) diffusion coefficient (D) and solubility (S) of hydrogen are quantified with an upgraded diffusion analysis program. These methods are applied to three cylindrical rubbers. Dual adsorption behaviors with increasing pressure are observed for all the samples. C∞ follows Henry’s law up to ~15 MPa whereas Langmuir model applies up to 90 MPa. D shows Knudsen and bulk diffusion behavior below and above pressure respectively. A COMSOL simulation is compared with experimental observations.
Effect of Copper Cobalt Oxide Composition on Oxygen Evolution Electrocatalysts for Anion Exchange Membrane Water Electrolysis
Nov 2020
Publication
Copper cobalt oxide nanoparticles (CCO NPs) were synthesized as an oxygen evolution electrocatalyst via a simple co-precipitation method with the composition being controlled by altering the precursor ratio to 1:1 1:2 and 1:3 (Cu:Co) to investigate the effects of composition changes. The effect of the ratio of Cu2+/Co3+ and the degree of oxidation during the co-precipitation and annealing steps on the crystal structure morphology and electrocatalytic properties of the produced CCO NPs were studied. The CCO1:2 electrode exhibited an outstanding performance and high stability owing to the suitable electrochemical kinetics which was provided by the presence of sufficient Co3+ as active sites for oxygen evolution and the uniform sizes of the NPs in the half cell. Furthermore single cell tests were performed to confirm the possibility of using the synthesized electrocatalyst in a practical water splitting system. The CCO1:2 electrocatalyst was used as an anode to develop an anion exchange membrane water electrolyzer (AEMWE) cell. The full cell showed stable hydrogen production for 100 h with an energetic efficiency of >71%. In addition it was possible tomass produce the uniform highly active electrocatalyst for such applications through the co-precipitation method.
Enhancing the Hydrogen Storage Properties of AxBy Intermetallic Compounds by Partial Substitution: A Short Review
Dec 2020
Publication
Solid-state hydrogen storage covers a broad range of materials praised for their gravimetric volumetric and kinetic properties as well as for the safety they confer compared to gaseous or liquid hydrogen storage methods. Among them AxBy intermetallics show outstanding performances notably for stationary storage applications. Elemental substitution whether on the A or B site of these alloys allows the effective tailoring of key properties such as gravimetric density equilibrium pressure hysteresis and cyclic stability for instance. In this review we present a brief overview of partial substitution in several AxBy alloys from the long-established AB5 and AB2-types to the recently attractive and extensively studied AB and AB3 alloys including the largely documented solid-solution alloy systems. We not only present classical and pioneering investigations but also report recent developments for each AxBy category. Special care is brought to the influence of composition engineering on desorption equilibrium pressure and hydrogen storage capacity. A simple overview of the AxBy operating conditions is provided hence giving a sense of the range of possible applications whether for low- or high-pressure systems.
A Flammability Limit Model for Hydrogen-air-diluent Mixtures Based on Heat Transfer Characteristics in Flame Propagation
May 2019
Publication
Predicting lower flammability limits (LFL) of hydrogen has become an ever-important task for safety of nuclear industry. While numerous experimental studies have been conducted LFL results applicable for the harsh environment are still lack of information. Our aim is to develop a calculated non-adiabatic flame temperature (CNAFT) model to better predict LFL of hydrogen mixtures in nuclear power plant. The developed model is unique for incorporating radiative heat loss during flame propagation using the CNAFT coefficient derived through previous studies of flame propagation. Our new model is more consistent with the experimental results for various mixtures compared to the previous model which relied on calculated adiabatic flame temperature (CAFT) to predict the LFL without any consideration of heat loss. Limitation of the previous model could be explained clearly based on the CNAFT coefficient magnitude. The prediction accuracy for hydrogen mixtures at elevated initial temperatures and high helium content was improved substantially. The model reliability was confirmed for H2-air mixtures up to 300 C and H2-air-He mixtures up to 50 vol % helium concentration. Therefore the CNAFT model developed based on radiation heat loss is expected as the practical method for predicting LFL in hydrogen risk analysis.
Behavior of Barrier Wall under Hydrogen Storage Tank Explosion with Simulation and TNT Equivalent Weight Method
Mar 2023
Publication
Hydrogen gas storage place has been increasing daily because of its consumption. Hydrogen gas is a dream fuel of the future with many social economic and environmental benefits to its credit. However many hydrogen storage tanks exploded accidentally and significantly lost the economy infrastructure and living beings. In this study a protection wall under a worst-case scenario explosion of a hydrogen gas tank was analyzed with commercial software LS-DYNA. TNT equivalent method was used to calculate the weight of TNT for Hydrogen. Reinforced concrete and composite protection wall under TNT explosion was analyzed with a different distance of TNT. The initial dimension of the reinforced concrete protection wall was taken from the Korea gas safety code book (KGS FP217) and studied the various condition. H-beam was used to make the composite protection wall. Arbitrary-Lagrangian-Eulerian (ALE) simulation from LS-DYNA and ConWep pressure had a good agreement. Used of the composite structure had a minimum displacement than a normal reinforced concrete protection wall. During the worst-case scenario explosion of a hydrogen gas 300 kg storage tank the minimum distance between the hydrogen gas tank storage and protection wall should be 3.6 m.
Machine Learning Approach for Prediction of Hydrogen Environment Embrittlement in Austenitic Steels
Jun 2022
Publication
This study introduces a machine learning approach to predict the effect of alloying elements and test conditions on the hydrogen environment embrittlement (HEE) index of austenitic steels for the first time. The correlation between input features and the HEE index was analyzed with Pearson's correlation coefficient (PCC) and Maximum Information Coefficient (MIC) algorithms. The correlation analysis results identified Ni and Mo as dominant features influencing the HEE index of austenitic steels. Based on the analysis results the performance of the four representative machine learning models as a function of the number of top-ranked features was evaluated: random forest (RF) linear regression (LR) Bayesian ridge (BR) and support vector machine (SVM). Regardless of the type and the number of top-ranking features the RF model had the highest accuracy among various models. The machine learning-based approach is expected to be useful in designing new steels having mechanical properties required for hydrogen applications.
Solid Air Hydrogen Liquefaction, the Missing Link of the Hydrogen Economy
Mar 2023
Publication
The most challenging aspect of developing a green hydrogen economy is long-distance oceanic transportation. Hydrogen liquefaction is a transportation alternative. However the cost and energy consumption for liquefaction is currently prohibitively high creating a major barrier to hydrogen supply chains. This paper proposes using solid nitrogen or oxygen as a medium for recycling cold energy across the hydrogen liquefaction supply chain. When a liquid hydrogen (LH2) carrier reaches its destination the regasification process of the hydrogen produces solid nitrogen or oxygen. The solid nitrogen or oxygen is then transported in the LH2 carrier back to the hydrogen liquefaction facility and used to reduce the energy consumption cooling gaseous hydrogen. As a result the energy required to liquefy hydrogen can be reduced by 25.4% using N2 and 27.3% using O2. Solid air hydrogen liquefaction (SAHL) can be the missing link for implementing a global hydrogen economy.
A Preliminary Study on an Alternative Ship Propulsion System Fueled by Ammonia: Environmental and Economic Assessments
Mar 2020
Publication
The shipping industry is becoming increasingly aware of its environmental responsibilities in the long-term. In 2018 the International Maritime Organization (IMO) pledged to reduce greenhouse gas (GHG) emissions by at least 50% by the year 2050 as compared with a baseline value from 2008. Ammonia has been regarded as one of the potential carbon-free fuels for ships based on these environmental issues. In this paper we propose four propulsion systems for a 2500 Twenty-foot Equivalent Unit (TEU) container feeder ship. All of the proposed systems are fueled by ammonia; however different power systems are used: main engine generators polymer electrolyte membrane fuel cell (PEMFC) and solid oxide fuel cell (SOFC). Further these systems are compared to the conventional main engine propulsion system that is fueled by heavy fuel oil with a focus on the economic and environmental perspectives. By comparing the conventional and proposed systems it is shown that ammonia can be a carbon-free fuel for ships. Moreover among the proposed systems the SOFC power system is the most eco-friendly alternative (up to 92.1%) even though it requires a high lifecycle cost than the others. Although this study has some limitations and assumptions the results indicate a meaningful approach toward solving GHG problems in the maritime industry.
Effects of Hydrogen Mixture Ratio and Scavenging Air Temperature on Combustion and Emission Characteristics of a 2-stroke Marine Engine
Nov 2022
Publication
A numerical study was conducted to investigate the effects of hydrogen and scavenging air temperature (SAT) on the combustion and emission characteristics of a 2-stroke heavy-duty dual-fuel (DF) marine engine at full load. The engine had a 700 mm bore fuelled with hydrogen–methane (H2-CH4) mixtures. Three-dimensional simulations of the combustion and emission formation inside the engine cylinder with various H2 contents in the H2-CH4 mixture were performed. ANSYS FLUENT simulation software was used to analyse the engine performance in-cylinder pressure temperature and emission characteristics. The CFD models were validated against the measured data recorded from the engine experiments. The results showed that an increase in the in-cylinder peak pressure increased the engine power when the H2 content in the H2-CH4 mixture increased. Notably CO2 and soot emissions decreased (up to more than 65%) when the H2 content in the gaseous mixture increased to 50%. Specific NO emissions in the DF modes were lower than that of the diesel mode when the H2 content in the gaseous mixture was lower than 40%. However they increased compared to the diesel mode when the H2 content continued to increase. This limits the H2 amount that should be used in a gaseous mixture creating NO emissions. The results also showed that the SAT cooling method can further reduce emission problems while enhancing engine power. In particular reducing the SAT to 28 ◦C in the gaseous mixture with 10% H2 ensured that the DF mode emitted the lowest NO emissions compared to the diesel mode. This reduced NO emissions by 37.92% compared to the measured NO emissions of the research engine (a Tier II marine engine). This study successfully analysed the benefits of using an H2-CH4 mixture as the primary fuel and the SAT cooling method in a 2-stroke ME-GI heavy-duty marine engine.
Preparation of Gas Standards for Quality Assurance of Hydrogen Fuel
May 2022
Publication
This study has developed traceable standards for evaluating impurities in hydrogen fuel according to ISO 14687. Impurities in raw H2 including sub mmol/mol levels of CO CO2 and CH4 were analyzed using multiple detectors while avoiding contamination. The gravimetric standards prepared included mixtures of the following nominal concentrations: 1 2 3e5 8e11 17e23 and 47e65 mmol/mol for CO2 CH4 and CO O2 N2 Ar and He respectively. The expanded uncertainty ranges were 0.8% for Ar N2 and He 1% for CH4 and CO and 2% for CO2 and O2. These standards were stable while that for CO varied by only 0.5% during a time span of three years. The prepared standards are useful for evaluating the compliance of H2 fuel in service stations with ISO 14687 quality requirements.
Artificial Intelligence/Machine Learning in Energy Management Systems, Control, and Optimization of Hydrogen Fuel Cell Vehicles
Mar 2023
Publication
Environmental emissions global warming and energy-related concerns have accelerated the advancements in conventional vehicles that primarily use internal combustion engines. Among the existing technologies hydrogen fuel cell electric vehicles and fuel cell hybrid electric vehicles may have minimal contributions to greenhouse gas emissions and thus are the prime choices for environmental concerns. However energy management in fuel cell electric vehicles and fuel cell hybrid electric vehicles is a major challenge. Appropriate control strategies should be used for effective energy management in these vehicles. On the other hand there has been significant progress in artificial intelligence machine learning and designing data-driven intelligent controllers. These techniques have found much attention within the community and state-of-the-art energy management technologies have been developed based on them. This manuscript reviews the application of machine learning and intelligent controllers for prediction control energy management and vehicle to everything (V2X) in hydrogen fuel cell vehicles. The effectiveness of data-driven control and optimization systems are investigated to evolve classify and compare and future trends and directions for sustainability are discussed.
Risk Assessment of a Hydrogen Refueling Station in an Urban Area
May 2023
Publication
After the Paris Agreement was signed in 2015 many countries worldwide focused on the hydrogen economy aiming for eco-friendly and renewable energy by moving away from the existing carbon economy which has been the primary source of global warming. Hydrogen is the most common element on Earth. As a light substance hydrogen can diffuse quickly; however it also has a small risk of explosion. Representative explosion accidents have included the Muskingum River Power Plant Vapor Cloud Explosion accident in 2007 and the Silver Eagle Refinery Vapor Cloud Explosion accident in 2009. In addition there was an explosion in a hydrogen tank in Gangneung Korea in May 2019 and a hydrogen refueling station (HRS) in Norway exploded in 2018. Despite this risk Korea is promoting the establishment of HRSs in major urban centers including downtown areas and public buildings by using the Regulatory Sandbox to install HRSs. This paper employed the Hydrogen Risk Assessment Model (HyRAM) of Sandia National Laboratories (SNL) a quantitative risk assessment (QRA) program specialized in hydrogen energy for HRSs installed in major urban hubs. A feasibility evaluation of the site conditions of an HRS was conducted using the French land use planning method based on the results obtained through evaluation using the HyRAM and the overpressure results of PHAST 8.0. After a risk assessment we confirmed that an HRS would be considered safe even if it was installed in the city center within a radius of influence of jet fires and overpressure.
Frequency Regulation of an Islanded Microgrid Using Hydrogen Energy Storage Systems: A Data-Driven Control Approach
Nov 2022
Publication
Hydrogen energy storage (HES) systems have recently received attention due to their potential to support real-time power balancing in a power grid. This paper proposes a data-driven model predictive control (MPC) strategy for HES systems in coordination with distributed generators (DGs) in an islanded microgrid (MG). In the proposed strategy a data-driven model of the HES system is developed to reflect interactive operations of an electrolyzer hydrogen tank and fuel cell and hence the optimal power sharing with DGs is achieved to support real-time grid frequency regulation (FR). The MG-level controller cooperates with a device-level controller of the HES system that overrides the FR support based on the level of hydrogen. Small-signal analysis is used to evaluate the contribution of FR support. Simulation case studies are also carried out to verify the accuracy of the data-driven model and the proposed strategy is effective for improving the real-time MG frequency regulation compared with the conventional PI-based strategy.
Green Hydrogen Production Technologies from Ammonia Cracking
Nov 2022
Publication
The rising technology of green hydrogen supply systems is expected to be on the horizon. Hydrogen is a clean and renewable energy source with the highest energy content by weight among the fuels and contains about six times more energy than ammonia. Meanwhile ammonia is the most popular substance as a green hydrogen carrier because it does not carry carbon and the total hydrogen content of ammonia is higher than other fuels and is thus suitable to convert to hydrogen. There are several pathways for hydrogen production. The considered aspects herein include hydrogen production technologies pathways based on the raw material and energy sources and different scales. Hydrogen can be produced from ammonia through several technologies such as electro-chemical photocatalytic and thermochemical processes that can be used at production plants and fueling stations taking into consideration the conversion efficiency reactors catalysts and their related economics. The commercial process is conducted by using expensive Ru catalysts in the ammonia converting process but is considered to be replaced by other materials such as Ni Co La and other perovskite catalysts which have high commercial potential with equivalent activity for extracting hydrogen from ammonia. For successful engraftment of ammonia to hydrogen technology into industry integration with green technologies and economic methods as well as safety aspects should be carried out.
Effect of the High-Pressure Hydrogen Gas Exposure in the Silica-Filled EPDM Sealing Composites with Different Silica Content
Mar 2022
Publication
With the increasing interest in hydrogen energy the stability of hydrogen storage facilities and components is emphasized. In this study we analyzed the effect of high-pressure hydrogen gas treatment in silica-filled EPDM composites with different silica contents. In detail cure characteristics crosslink density mechanical properties and hydrogen permeation properties were investigated. Results showed that material volume remaining hydrogen content and mechanical properties were changed after 96.3 MPa hydrogen gas exposure. With an increase in the silica content the crosslink density and mechanical properties increased but hydrogen permeability was decreased. After treatment high-silica-content composites showed lower volume change than low-silica-content composites. The crack damage due to the decompression caused a decrease in mechanical properties but high silica content can inhibit the reduction in mechanical properties. In particular EPDM/silica composites with a silica content of above 60 phr exhibited excellent resistance to hydrogen gas as no change in their physical and mechanical properties was observed.
Technology Portfolio Assessment for Near-zero Emission Iron and Steel Industry in China
May 2023
Publication
China aims to peak CO2 emissions before 2030 and to achieve carbon neutrality before 2060; hence industrial sectors in China are keen to figure out appropriate pathways to support the national target of carbon neutrality. The objective of this study is to explore near-zero emission pathways for the steel industry of China through a detailed technology assessment. The innovative technology development has been simulated using the AIM-China/steel model developed by including material-based technologies and optimal cost analysis. Six scenarios have been given in terms of different levels of production output emission reduction and carbon tax. Near-zero emission and carbon tax scenarios have shown that China’s steel industry can achieve near-zero emission using electric furnaces and hydrogen-based direct reduction iron technologies with policy support. Based on these technologies minimised production costs have been calculated revealing that the steel produced by these technologies is cost-effective. Moreover the feedstock cost can play a key role in these technology portfolios especially the cost of scrap iron ore and hydrogen. In addition the feedstock supply can have strong regional effects and can subsequently impact the allocation of steelmaking in the future. Therefore China can achieve near-zero emissions in the steel industry and electric furnace and hydrogen-based direct reduction iron technologies are crucial to achieving them.
Energy Management Control Strategy for Saving Trip Costs of Fuel Cell/Battery Electric Vehicles
Mar 2022
Publication
Fuel cell vehicles (FCVs) should control the energy management between two energy sources for fuel economy using the stored energy in a battery or generation of energy through a fuel cell system. The fuel economy for an FCV includes trip costs for hydrogen consumption and the lifetime of two energy sources. This paper proposes an implementable energy management control strategy for an FCV to reduce trip costs. The concept of the proposed control strategy is first to analyze the allowable current of a fuel cell system from the optimal strategies for various initial battery state of charge (SOC) conditions using dynamic programming (DP) and second to find a modulation ratio determining the current of a fuel cell system for driving a vehicle using the particle swarm optimization method. The control strategy presents the on/off moment of a fuel cell system and the proper modulation ratio of the turned-on fuel cell system with respect to the battery SOC and the power demand. The proposed strategy reduces trip costs in real-time similar to the DP-based optimal strategy and more than the simple energy control strategy of switching a fuel cell system on/off at the battery SOC boundary conditions even for long-term driving cycles.
Economic Analysis on Hydrogen Pipeline Infrastructure Establishment Scenarios: Case Study of South Korea
Sep 2022
Publication
South Korea has a plan to realize a hydrogen economy and it is essential to establish a main hydrogen pipeline for hydrogen transport. This study develops a cost estimation model applicable to the construction of hydrogen pipelines and conducts an economic analysis to evaluate various scenarios for hydrogen pipeline construction. As a result the cost of modifying an existing natural gas to a hydrogen pipeline is the lowest however there are issues with the safety of the modified hydrogen pipes from natural gas and the necessity of the existing natural gas pipelines. In the case of a short-distance hydrogen pipeline the cost is about 1.8 times that of the existing natural gas pipeline modification but it is considered a transitional scenario before the construction of the main hydrogen pipeline nationwide. Lastly in the case of long-distance main hydrogen pipeline construction it takes about 3.7 times as much cost as natural gas pipeline modification however it has the advantage of being the ultimate hydrogen pipeline network. In this study various hydrogen pipeline establishment scenarios ware compared. These results are expected to be utilized to establish plans for building hydrogen pipelines and to evaluate their economic feasibility.
Research Efforts for the Resolution of Hydrogen Risk
Jan 2015
Publication
During the past 10 years the Korea Atomic Energy Research Institute (KAERI) has performed a study to control hydrogen gas in the containment of the nuclear power plants. Before the Fukushima accident analytical activities for gas distribution analysis in experiments and plants were primarily conducted using a multidimensional code: the GASFLOW. After the Fukushima accident the COM3D code which can simulate a multi-dimensional hydrogen explosion was introduced in 2013 to complete the multidimensional hydrogen analysis system. The code validation efforts of the multidimensional codes of the GASFLOW and the COM3D have continued to increase confidence in the use of codes using several international experimental data. The OpenFOAM has been preliminarily evaluated for APR1400 containment based on experience from coded validation and the analysis of hydrogen distribution and explosion using the multidimensional codes the GASFLOW and the COM3D. Hydrogen safety in nuclear power has become a much more important issue after the Fukushima event in which hydrogen explosions occurred. The KAERI is preparing a large-scale test that can be used to validate the performance of domestic passive autocatalytic recombiners (PARs) and can provide data for the validation of the severe accident code being developed in Korea
Optimization of Component Sizing for a Fuel Cell-Powered Truck to Minimize Ownership Cost
Mar 2019
Publication
In this study we consider fuel cell-powered electric trucks (FCETs) as an alternative to conventional medium- and heavy-duty vehicles. FCETs use a battery combined with onboard hydrogen storage for energy storage. The additional battery provides regenerative braking and better fuel economy but it will also increase the initial cost of the vehicle. Heavier reliance on stored hydrogen might be cheaper initially but operational costs will be higher because hydrogen is more expensive than electricity. Achieving the right tradeoff between these power and energy choices is necessary to reduce the ownership cost of the vehicle. This paper develops an optimum component sizing algorithm for FCETs. The truck vehicle model was developed in Autonomie a platform for modelling vehicle energy consumption and performance. The algorithm optimizes component sizes to minimize overall ownership cost while ensuring that the FCET matches or exceeds the performance and cargo capacity of a conventional vehicle. Class 4 delivery truck and class 8 linehaul trucks are shown as examples. We estimate the ownership cost for various hydrogen costs powertrain components ownership periods and annual vehicle miles travelled.
On-Board Cold Thermal Energy Storage System for Hydrogen Fueling Process
Feb 2019
Publication
The hydrogen storage pressure in fuel cell vehicles has been increased from 35 MPa to 70 MPa in order to accommodate longer driving range. On the downside such pressure increase results in significant temperature rise inside the hydrogen tank during fast filling at a fueling station which may pose safety issues. Installation of a chiller often mitigates this concern because it cools the hydrogen gas before its deposition into the tank. To address both the energy efficiency improvement and safety concerns this paper proposed an on-board cold thermal energy storage (CTES) system cooled by expanded hydrogen. During the driving cycle the proposed system uses an expander instead of a pressure regulator to generate additional power and cold hydrogen gas. Moreover CTES is equipped with phase change materials (PCM) to recover the cold energy of the expanded hydrogen gas which is later used in the next filling to cool the high-pressure hydrogen gas from the fueling station.
Life Cycle Assessment of Alternative Ship Fuels for Coastal Ferry Operating in Republic of Korea
Aug 2020
Publication
In this study the environmental impacts of various alternative ship fuels for a coastal ferry were assessed by the life cycle assessment (LCA) analysis. The comparative study was performed with marine gas oil (MGO) natural gas and hydrogen with various energy sources for a 12000 gross tonne (GT) coastal ferry operating in the Republic of Korea (ROK). Considering the energy imports of ROK i.e. MGO from Saudi Arabia and natural gas from Qatar these countries were chosen to provide the MGO and the natural gas for the LCA. The hydrogen is considered to be produced by steam methane reforming (SMR) from natural gas with hard coal nuclear energy renewable energy and electricity in the ROK model. The lifecycles of the fuels were analyzed in classifications of Well-toTank Tank-to-Wake and Well-to-Wake phases. The environmental impacts were provided in terms of global warming potential (GWP) acidification potential (AP) photochemical potential (POCP) eutrophication potential (EP) and particulate matter (PM). The results showed that MGO and natural gas cannot be used for ships to meet the International Maritime Organization’s (IMO) 2050 GHG regulation. Moreover it was pointed out that the energy sources in SMR are important contributing factors to emission levels. The paper concludes with suggestions for a hydrogen application plan for ships from small nearshore ships in order to truly achieve a ship with zero emissions based on the results of this study.
Hydrogen Technology Development and Policy Status by Value Chain in South Korea
Nov 2022
Publication
Global transitions from carbon- to hydrogen-based economies are an essential component of curbing greenhouse gas emissions and climate change. This study provides an investigative review of the technological development trends within the overall hydrogen value chain in terms of production storage transportation and application with the aim of identifying patterns in the announcement and execution of hydrogen-based policies both domestically within Korea as well as internationally. The current status of technological trends was analyzed across the three areas of natural hydrogen carbon dioxide capture utilization and storage technology linked to blue hydrogen and green hydrogen production linked to renewable energy (e.g. water electrolysis). In Korea the establishment of underground hydrogen storage facilities is potentially highly advantageous for the storage of domestically produced and imported hydrogen providing the foundations for large-scale application as economic feasibility is the most important national factor for the provision of fuel cells. To realize a hydrogen economy pacing policy and technological development is essential in addition to establishing a roadmap for efficient policy support. In terms of technological development it is important to prioritize that which can connect the value chain all of which will ultimately play a major role in the transformation of human energy consumption.
Potential Global Warming Impact of 1 kW Polymer Electrolyte Membrane Fuel Cell System for Residential Buildings on Operation Phase
Mar 2023
Publication
This study established global warming potential(GWP) emission factors through a life cycle assessment on the operation phases of two different 1 kW polymer electrolyte membrane fuel cell (PEMFC) systems for residential buildings (NG-PEMFC fed with hydrogen from natural gas reforming; WE-PEMFC fed with hydrogen from photovoltaics-powered water electrolyzer). Their effectiveness was also compared with conventional power grid systems in Korea specifically in the area of greenhouse gas emissions. The operation phases of the NG-PEMFC and the WE-PEMFC were divided into burner reformer and stack and into water electrolysis and stack respectively. The functional unit of each fuel cell system was defined as 1 kWh of electricity production. In the case of NG-PEMFC the GWP was 3.72E-01 kg-CO2eq/kWh the embodied carbon emissions due to using city gas during the life cycle process was about 20.87 % the carbon emission ratio according to the reformer's combustion burner was 6.07 % and the direct carbon emission ratio of the air emissions from the reformer was 73.06 % indicating that the carbon emission from the reformer contributed over 80 % of the total GWP. As for the WE-PEMFC the GWP was 1.76E-01 kg-CO2eq/kWh and the embodied carbon emissions from photovoltaic power generation during the life cycle process contributed over 99 % of the total GWP.
Minimum Fire Size for Hydrogen Storage Tank Fire Test Protocol for Hydrogen-powered Electric City Bus Determine Via Risk-based Approach
Sep 2021
Publication
As part of the United Nations Global Technical Regulation No. 13 (UN GTR #13 [1]) vehicle fire safety is validated using a localized and engulfing fire test methodology and currently updates are being considered in the on-going Phase 2 development stage. The GTR#13 fire test is designed to verify the performance of a hydrogen storage system of preventing rupture when exposed to service-terminating condition of fire situation. The test is conducted in two stages – localized flame exposure at a location most challenging for thermally-activated pressure relief device(s) (TPRDs) to respond for 10 min. followed by engulfing fire exposure until the system vents and the pressure falls to less than 1 MPa or until “time out” (30min. for light-duty vehicle containers and 60 min. for heavy-duty vehicle containers). The rationale behind this two-stage fire test is to ensure that even when fire sizes are small and TPRDs are not responding the containers have fire resistance to withstand or fire sensitivity to respond to a localized fire to avoid system rupture. In this study appropriate fire sizes for localized and engulfing fire tests in GTR#13 are evaluated by considering actual fire conditions in a hydrogen-powered electric city bus. Quantitative risk analysis is conducted to develop various fire accident scenarios including regular bus fire battery fire and hydrogen leak fire. Frequency and severity analyses are performed to determine the minimum fire size required in GTR#13 fire test to ensure hydrogen storage tank safety in hydrogen-powered electric city buses.
Comparative Study on Ammonia and Liquid Hydrogen Transportation Costs in Comparison to LNG
Feb 2023
Publication
Since ammonia and liquid hydrogen are the optional future shipping cargo and fuels the applicability was crucial using the current technologies and expectations. Existing studies for the economic feasibility of the energies had limitations: empirical evaluation with assumptions and insufficiency related to causality. A distorted estimation can result in failure of decision-making or policy in terms of future energy. The present study aimed to evaluate the transportation costs of future energy including ammonia and liquid hydrogen in comparison to LNG for overcoming the limitations. An integrated mathematical model was applied to the investigation for economic feasibility. The transportation costs of the chosen energies were evaluated for the given transportation plan considering key factors: ship speed BOR and transportation plan. The transportation costs at the design speed for LNG and liquid hydrogen were approximately 55 % and 80 % of that for ammonia without considering the social cost due to CO2 emission. Although ammonia was the most expensive energy for transportation ammonia could be an effective alternative due to insensitivity to the transportation plan. If the social cost was taken into account liquid hydrogen already gained competitiveness in comparison to LNG. The advantage of liquid hydrogen was maximized for higher speed where more BOG was injected into main engines.
Annealing Effects on SnO2 Thin Film for H2 Gas Sensing
Sep 2022
Publication
Hydrogen (H2 ) is attracting attention as a renewable energy source in various fields. However H2 has a potential danger that it can easily cause a backfire or explosion owing to minor external factors. Therefore H2 gas monitoring is significant particularly near the lower explosive limit. Herein tin dioxide (SnO2 ) thin films were annealed at different times. The as-obtained thin films were used as sensing materials for H2 gas. Here the performance of the SnO2 thin film sensor was studied to understand the effect of annealing and operating temperature conditions of gas sensors to further improve their performance. The gas sensing properties exhibited by the 3-h annealed SnO2 thin film showed the highest response compared to the unannealed SnO2 thin film by approximately 1.5 times. The as-deposited SnO2 thin film showed a high response and fast response time to 5% H2 gas at 300 ◦C of 257.34% and 3 s respectively.
Recent Application of Nanomaterials to Overcome Technological Challenges of Microbial Electrolysis Cells
Apr 2022
Publication
Microbial electrolysis cells (MECs) have attracted significant interest as sustainable green hydrogen production devices because they utilize the environmentally friendly biocatalytic oxidation of organic wastes and electrochemical proton reduction with the support of relatively lower external power compared to that used by water electrolysis. However the commercialization of MEC technology has stagnated owing to several critical technological challenges. Recently many attempts have been made to utilize nanomaterials in MECs owing to the unique physicochemical properties of nanomaterials originating from their extremely small size (at least <100 nm in one dimension). The extraordinary properties of nanomaterials have provided great clues to overcome the technological hurdles in MECs. Nanomaterials are believed to play a crucial role in the commercialization of MECs. Thus understanding the technological challenges of MECs the characteristics of nanomaterials and the employment of nanomaterials in MECs could be helpful in realizing commercial MEC technologies. Herein the critical challenges that need to be addressed for MECs are highlighted and then previous studies that used nanomaterials to overcome the technological difficulties of MECs are reviewed.
Review of the Liquid Hydrogen Storage Tank and Insulation System for the High-Power Locomotive
Jun 2022
Publication
Hydrogen has been attracting attention as a fuel in the transportation sector to achieve carbon neutrality. Hydrogen storage in liquid form is preferred in locomotives ships drones and aircraft because these require high power but have limited space. However liquid hydrogen must be in a cryogenic state wherein thermal insulation is a core problem. Inner materials including glass bubbles multi-layer insulation (MLI) high vacuum and vapor-cooled shields are used for thermal insulation. An analytic study is preferred and proceeds liquid hydrogen tanks due to safety regulations in each country. This study reviewed the relevant literature for thermodynamic modeling. The literature was divided into static dynamic and systematic studies. In summary the authors summarized the following future research needs: The optimal design of the structure including suspension baffle and insulation system can be studied to minimize the boil-off gas (BOG). A dynamic study of the pressure mass flow and vaporizer can be completed. The change of the components arrangement from the conventional diesel–electric locomotive is necessary.
What Can Accelerate Technological Convergence of Hydrogen Energy: A Regional Perspective
Jun 2023
Publication
Focusing on technological innovation and convergence is crucial for utilizing hydrogen energy an emerging infrastructure area. This research paper analyzes the extent of technological capabilities in a region that could accelerate the occurrence of technological convergence in the fields related to hydrogen energy through the use of triadic patents their citation information and their regional information. The results of the Bayesian spatial model indicate that the active exchange of diverse original technologies could facilitate technological convergence in the region. On the other hand it is difficult to achieve regional convergence with regard to radical technology. The findings could shed light on the establishment of an R&D strategy for hydrogen technologies. This study could contribute to the dissemination and utilization of hydrogen technologies for sustainable industrial development.
No more items...