Norway
Pathways to Low-cost Clean Hydrogen Production with Gas Switching Reforming
Feb 2020
Publication
Gas switching reforming (GSR) is a promising technology for natural gas reforming with inherent CO2 capture. Like conventional steam methane reforming (SMR) GSR can be integrated with CO2 -gas shift and pressure swing adsorption units for pure hydrogen production. The resulting GSR-H2 process concept was techno-economically assessed in this study. Results showed that GSR-H2 can achieve 96% CO2 capture at a CO2 avoidance cost of 15 $/ton (including CO2 transport and storage). Most components of the GSR-H2 process are proven technologies but long-term oxygen carrier stability presents an important technical uncertainty that can adversely affect competitiveness when the material lifetime drops below one year. Relative to the SMR benchmark GSR-H2 replaces some fuel consumption with electricity consumption making it more suitable to regions with higher natural gas prices and lower electricity prices. Some minor alterations to the process configuration can adjust the balance between fuel and electricity consumption to match local market conditions. The most attractive commercialization pathway for the GSR-H2 technology is initial construction without CO2 capture followed by simple retrofitting for CO2 capture when CO2 taxes rise and CO2 transport and storage infrastructure becomes available. These features make the GSR-H2 technology robust to almost any future energy market scenario.
3D Risk Management for Hydrogen Installations (HY3DRM)
Oct 2015
Publication
This paper introduces the 3D risk management (3DRM) concept with particular emphasis on hydrogen installations (Hy3DRM). The 3DRM framework entails an integrated solution for risk management that combines a detailed site-specific 3D geometry model a computational fluid dynamics (CFD) tool for simulating flow-related accident scenarios methodology for frequency analysis and quantitative risk assessment (QRA) and state-of-the-art visualization techniques for risk communication and decision support. In order to reduce calculation time and to cover escalating accident scenarios involving structural collapse and projectiles the CFD-based consequence analysis can be complemented with empirical engineering models reduced order models or finite element analysis (FEA). The paper outlines the background for 3DRM and presents a proof-of-concept risk assessment for a hypothetical hydrogen filling station. The prototype focuses on dispersion fire and explosion scenarios resulting from loss of containment of gaseous hydrogen. The approach adopted here combines consequence assessments obtained with the CFD tool FLACS-Hydrogen from Gexcon and event frequencies estimated with the Hydrogen Risk Assessment Models (HyRAM) tool from Sandia to generate 3D risk contours for explosion pressure and radiation loads. For a given population density and set of harm criteria it is straightforward to extend the analysis to include personnel risk as well as risk-based design such as detector optimization. The discussion outlines main challenges and inherent limitations of the 3DRM concept as well as prospects for further development towards a fully integrated framework for risk management in organizations.
Effect of Anion Exchange Ionomer Content on Electrode Performance in AEM Water Electrolysis
Aug 2020
Publication
Anion exchange membrane water electrolysis (AEMWE) has acquired substantial consideration as a cost-effective hydrogen production technology. The anion ionomer content in the catalyst layers during hydrogen and oxygen evolution reaction (HER and OER) is of ultimate significance. Herein an in-situ half-cell analysis with reference electrodes was carried out for simultaneous potential measurements and identification of the influence of the anion exchange ionomer (AEI) content on anode and cathode performance. The measured half-cell potentials proved the influence of AEI content on the catalytic activity of HER and OER which was supported by the rotating disk electrode (RDE) measurements. Cathode overpotential of Ni/C was not negligible and more affected by the AEI content than anode with the optimized AEI content of 10 wt% while NiO anode OER overpotential was independent of the AEI content. For the same AEI content PGM catalysts showed higher electroactivity than Ni-based catalysts for HER and OER and the cathode catalyst's intrinsic activity is of high importance in the AEM electrolysis operation. Post-mortem analysis by SEM mapping of both AEI and catalyst distributions on the electrode surface showed the effect of AEI loading on the catalyst morphology which could be related to the electrode performance.
Modelling and Simulation of a Zero-emission Hybrid Power Plant for a Domestic Ferry
Jan 2021
Publication
This paper presents a simulation tool for marine hybrid power-plants equipped with polymer exchange membrane fuel cells and batteries. The virtual model through the combination of operational data and dynamically modelled subsystems can simulate power-plants of different sizes and configurations in order to analyze the response of different energy management strategies. The model aims to replicate the realistic behavior of the components included in the vessel's grid to asses if the hardware selected by the user is capable of delivering the power set-point requested by the energy management system. The model can then be used to optimize key factors such as hydrogen consumption. The case study presented in the paper demonstrates how the model can be used for the evaluation of a retrofitting operation replacing a diesel electric power-plant with fuel cells and batteries. The vessel taken into consideration is a domestic ferry operating car and passenger transport in Denmark. The vessel is outfitted with a diesel electric plant and an alternative hybrid power-plant is proposed. The hybrid configuration is tested using the model in a discrete time-domain.
Hydrogen as a Maritime Fuel–Can Experiences with LNG Be Transferred to Hydrogen Systems?
Jul 2021
Publication
As the use of fossil fuels becomes more and more restricted there is a need for alternative fuels also at sea. For short sea distance travel purposes batteries may be a solution. However for longer distances when there is no possibility of recharging at sea batteries do not have sufficient capacity yet. Several projects have demonstrated the use of compressed hydrogen (CH2) as a fuel for road transport. The experience with hydrogen as a maritime fuel is very limited. In this paper the similarities and differences between liquefied hydrogen (LH2) and liquefied natural gas (LNG) as a maritime fuel will be discussed based on literature data of their properties and our system knowledge. The advantages and disadvantages of the two fuels will be examined with respect to use as a maritime fuel. Our objective is to discuss if and how hydrogen could replace fossil fuels on long distance sea voyages. Due to the low temperature of LH2 and wide flammability range in air these systems have more challenges related to storage and processing onboard than LNG. These factors result in higher investment costs. All this may also imply challenges for the LH2 supply chain.
Loss of Integrity of Hydrogen Technologies: A Critical Review
Jul 2020
Publication
Hydrogen is one of the main candidates in replacing fossil fuels in the forthcoming years. However hydrogen technologies must deal with safety aspects due to the specific substance properties. This study aims to provide an overview on the loss of integrity (LOI) of hydrogen equipment which may lead to serious consequences such as fires and explosions. Substantial information regarding the hydrogen lifecycle its properties and safety related aspects has gathered. Furthermore focus has placed on the phenomena responsible for the LOI (e.g. hydrogen embrittlement) and material selection for hydrogen services. Moreover a systematic review on the hydrogen LOI topic has conducted to identify and connect the most relevant and active research group within the topic. In conclusion a significant dearth of knowledge in material behaviour of hydrogen technologies has highlighted. It is thought that is possible to bridge this gap by strengthening the collaborations between scientists from different research fields.
Residual Performance of Composite Pressure Vessels Submitted to Mechanical Impacts
Sep 2017
Publication
Type IV pressure vessels are commonly used for hydrogen on-board stationary or bulk storages. During their lifetime they can be submitted to mechanical impacts creating damage within the composite structure not necessarily correlated to what is visible from the outside. When an impact is suspected or when a cylinder is periodically inspected it is necessary to determine whether it can safely stay in service or not. The FCH JU project Hypactor aims at creating a large database of impacts characterized by various non destructive testing (NDT) methods in order to provide reliable pass-fail criteria for damaged cylinders. This paper presents some of the tests results investigating short term burst) and long term (cycling) performance of impacted cylinders and the recommendations that can be made for impact testing and NDT criteria calibration.
Minimum Entropy Generation in a Heat Exchanger in the Cryogenic Part of the Hydrogen Liquefaction Process: On the Validity of Equipartition and Disappearance of the Highway
May 2019
Publication
Liquefaction of hydrogen is a promising technology for transporting large quantities of hydrogen across long distances. A key challenge is the high power consumption. In this work we discuss refrigeration strategies that give minimum entropy production/exergy destruction in a plate-fin heat exchanger that cools the hydrogen from 47.8 K to 29.3 K. Two reference cases are studied; one where the feed stream enters at 20 bar and one where it enters at 80 bar. Catalyst in the hot layers speeds up the conversion of ortho-to para-hydrogen. Optimal control theory is used to formulate a minimization problem where the objective function is the total entropy production the control variable is the temperature of the refrigerant and the constrains are the balance equations for energy mass and momentum in the hot layers. The optimal refrigeration strategies give a reduction of the total entropy production of 8.7% in the 20-bar case and 4.3% in the 80-bar case. The overall heat transfer coefficient and duty is higher in the 20 bar case which compensates for the increase in entropy production due to a thermal mismatch that is avoided in the 80 bar case. This leads the second law efficiency of the 20 bar case (91%) to be similar to the 80 bar case (89%). We demonstrate that equipartition of the entropy production and equipartition of the thermal driving force are both excellent design principles for the process unit considered with total entropy productions deviating only 0.2% and 0.5% from the state of minimum entropy production. Equipartition of the thermal driving force i.e. a constant difference between the inverse temperatures of the hot and cold layers represents a particularly simple guideline that works remarkably well. We find that both heat transfer and the spin-isomer reaction contribute significantly to the entropy production throughout the length of the process unit. Unlike previous examples in the literature the process unit considered in this work is not characterized by a “reaction mode” at the inlet followed by a “heat transfer mode”. Therefore it does not follow a highway in state space i.e. a band that is particularly dense with energy efficient solutions. By artificially increasing the spin-isomer conversion rate the highway appears when the conversion rate becomes sufficiently high.
Flexible Power and Hydrogen Production: Finding Synergy Between CCS and Variable Renewables
Dec 2019
Publication
The expansion of wind and solar power is creating a growing need for power system flexibility. Dispatchable power plants with CO2 capture and storage (CCS) offer flexibility with low CO2 emissions but these plants become uneconomical at the low running hours implied by renewables-based power systems. To address this challenge the novel gas switching reforming (GSR) plant was recently proposed. GSR can alternate between electricity and hydrogen production from natural gas offering flexibility to the power system without reducing the utilization rate of the capital stock embodied in CCS infrastructure. This study assesses the interplay between GSR and variable renewables using a power system model which optimizes investment and hourly dispatch of 13 different technologies. Results show that GSR brings substantial benefits relative to conventional CCS. At a CO2 price of V100/ton inclusion of GSR increases the optimal wind and solar share by 50% lowers total system costs by 8% and reduces system emissions from 45 to 4 kgCO2/MWh. In addition GSR produces clean hydrogen equivalent to about 90% of total electricity demand which can be used to decarbonize transport and industry. GSR could therefore become a key enabling technology for a decarbonization effort led by wind and solar power.
Efficient Hydrogen Production with CO2 Capture Using Gas Switching Reforming
Jul 2019
Publication
Hydrogen is a promising carbon-neutral energy carrier for a future decarbonized energy sector. This work presents process simulation studies of the gas switching reforming (GSR) process for hydrogen production with integrated CO2 capture (GSR-H2 process) at a minimal energy penalty. Like the conventional steam methane reforming (SMR) process GSR combusts the off-gas fuel from the pressure swing adsorption unit to supply heat to the endothermic reforming reactions. However GSR completes this combustion using the chemical looping combustion mechanism to achieve fuel combustion with CO2 separation. For this reason the GSR-H2 plant incurred an energy penalty of only 3.8 %-points relative to the conventional SMR process with 96% CO2 capture. Further studies showed that the efficiency penalty is reduced to 0.3 %-points by including additional thermal mass in the reactor to maintain a higher reforming temperature thereby facilitating a lower steam to carbon ratio. GSR reactors are standalone bubbling fluidized beds that will be relatively easy to scale up and operate under pressurized conditions and the rest of the process layout uses commercially available technologies. The ability to produce clean hydrogen with no energy penalty combined with this inherent scalability makes the GSR-H2 plant a promising candidate for further research.
Thermal Efficiency of On-site, Small-scale Hydrogen Production Technologies using Liquid Hydrocarbon Fuels in Comparison to Electrolysis a Case Study in Norway
Oct 2018
Publication
The main goal of this study was to assess the energy efficiency of a small-scale on-site hydrogen production and dispensing plant for transport applications. The selected location was the city of Narvik in northern Norway where the hydrogen demand is expected to be 100 kg/day. The investigated technologies for on-site hydrogen generation starting from common liquid fossil fuels such as heavy naphtha and diesel were based on steam reforming and partial oxidation. Water electrolysis derived by renewable energy was also included in the comparison. The overall thermal efficiency of the hydrogen station was computed including compression and miscellaneous power consumption.
Development of Tools for Risk Assessment and Risk Communication for Hydrogen Applications
Sep 2005
Publication
For decades risk assessment has been an important tool in risk management of activities in several industries world wide. It provides among others authorities and stakeholders with a sound basis for creating awareness about existing and potential hazards and risks and making decisions related to how they can prioritise and plan expenditures on risk reduction. The overall goal of the ongoing HySafe project is to contribute to the safe transition to a more sustainable development in Europe by facilitating the safe introduction of hydrogen technologies and applications. An essential element in this is the demonstration of safety: that all safety aspects related to production transportation and public use are controlled to avoid that introducing hydrogen as energy carrier should pose unacceptable risk to the society.<br/>History has proven that introducing risk analysis to new industries is beneficial e.g. in transportation and power production and distribution. However this will require existing methods and standards to be adapted to the specific applications. Furthermore when trying to quantify risk it is of utmost importance to have access to relevant accident and incident information. Such data may in many cases not be readily available and the utilisation of them will then require specific and long lasting data collection initiatives.<br/>In this paper we will present the work that has been undertaken in the HySafe project in developing methodologies and collecting data for risk management of hydrogen infrastructure. Focus is laid on the development of risk acceptance criteria and on the demonstration of safety and benefits to the public. A trustworthy demonstration of safety will have to be based on facts especially on facts widely known and emphasis will thus be put on the efforts taken to establish and operate a database containing hydrogen accident and incident information which can be utilised in risk assessment of hydrogen applications. A demonstration of safety will also have to include a demonstration of risk control measures and the paper will also present work carried out on safety distances and ignition source control.
Stress Corrosion Cracking Of Stainless Steels In High Pressure Alkaline Electrolysers
Sep 2005
Publication
Hydrogen-producing high-pressure electrolysers operating with 40% potassium hydroxide solution and an applied oxygen pressure up to 30 barg have been developed. Austenitic stainless steels of type AISI316L are deemed resistant to stress corrosion cracking (SCC) in concentrated KOH solutions. However SCC has on some occasions been observed on the oxygen side of the high-pressure electrolysers thereby representing a safety risk in the operation. Several materials have been tested for resistance to SCC using C-ring specimens in autoclaves under conditions similar to the high-pressure electrolysers and at temperatures up to 120°C. The tests confirmed the observed susceptibility of austenitic stainless steels to SCC in concentrated KOH solutions. Higher alloyed austenitic stainless steels also showed SCC. Duplex stainless steel and nickel based Alloy 28 showed good resistance to SCC in the given environment. Further tests are needed to define the optimum weld procedure.
Life Cycle Environmental Analysis of a Hydrogen-based Energy Storage System for Remote Applications
Mar 2022
Publication
Energy storage systems are required to address the fluctuating behaviour of variable renewable energy sources. The environmental sustainability of energy storage technologies should be carefully assessed together with their techno-economic feasibility. In this work an environmental analysis of a renewable hydrogen-based energy storage system has been performed making use of input parameters made available in the framework of the European REMOTE project. The analysis is applied to the case study of the Froan islands (Norway) which are representative of many other insular microgrid sites in northern Europe. The REMOTE solution is compared with other scenarios based on fossil fuels and submarine connections to the mainland grid. The highest climate impacts are found in the dieselbased configuration (1090.9 kgCO2eq/MWh) followed by the REMOTE system (148.2 kgCO2eq/MWh) and by the sea cable scenario (113.7 kgCO2eq/MWh). However the latter is biased by the very low carbon intensity of the Norwegian electricity. A sensitivity analysis is then performed on the length of the sea cable and on the CO2 emission intensity of electricity showing that local conditions have a strong impact on the results. The REMOTE system is also found to be the most cost-effective solution to provide electricity to the insular community. The in-depth and comparative (with reference to possible alternatives) assessment of the renewable hydrogen-based system aims to provide a comprehensive overview about the effectiveness and sustainability of these innovative solutions as a support for off-grid remote areas.
Simulation of Flame Acceleration and DDT in H2-air Mixture with a Flux Limiter Centred Method
Sep 2005
Publication
Flame acceleration and deflagration to detonation transition (DDT) is simulated with a numerical code based on a flux limiter centred method for hyperbolic differential equations. The energy source term is calculated by a Riemann solver for the in homogeneous Euler equations for the turbulent combustion and a two-step reaction model for hydrogen-air. The transport equations are filtered for large eddy simulation (LES) and the sub filter turbulence is modelled by a transport equation for the the turbulent kinetic energy. The flame tracking is handled by the G-equation for turbulent flames. Numerical results are compared to pressure histories from physical experiments. These experiments are performed in a closed circular 4m long tube with inner diameter of 0.107m. The tube is filled with hydrogen-air mixture at 1atm which is at rest when ignited. The ignition is located at one end of the tube. The tube is fitted with an obstruction with circular opening 1m down the tube from the ignition point. The obstruction has a blockage ratio of 0.92 and a thickness of 0.01m. The obstruction creates high pressures in the ignition end of the tube and very high gas velocities in and behind the obstruction opening. The flame experiences a detonation to deflagration transition (DDT) in the super sonic jet created by the obstruction. Pressure build-up in the ignition end of the tube is simulated with some discrepancies. The DDT in the supersonic jet is simulated but the position of the DDT is strongly dependent on the simulated pressure in the ignition end.
Assessment and Evaluation of 3rd Party Risk for Planned Hydrogen Demonstration Facility
Sep 2007
Publication
Potential risk exposure of 3rd parties i.e. people not involved in the actual operation of a plant is often a critical factor to gain authority approval and public acceptance for a development project. This is also highly relevant for development of demonstration facilities for hydrogen production and refuelling infrastructure. This paper presents and discusses results for risk exposure of 3rd parties based on risk assessment studies performed for the planned Hydrogen Technology Research Centre Hytrec in Trondheim. The methodology applied is outlined. Key assumptions and study uncertainties are identified and how these might affect the results are discussed.<br/>The purpose of Hytrec is to build a centre for research development and demonstration of hydrogen as an energy carrier. Hydrogen will be produced both by reforming of natural gas with CO2 capture and by electrolysis of water. The plant also includes a SOFC that will run on natural gas or hydrogen and produce heat and electricity for the Hytrec visitor centre. Hytrec will be located in a populated area without access control. Most of the units will be located within cabinets and modules.<br/>The authors acknowledge the Hytrec project and the Hytrec project partners Statoil Statkraft and DNV for their support and for allowing utilisation of results from the Hytrec QRA in this paper.
The Potential of Gas Switching Partial Oxidation Using Advanced Oxygen Carriers for Efficient H2 Production with Inherent CO2 Capture
May 2021
Publication
The hydrogen economy has received resurging interest in recent years as more countries commit to net-zero CO2 emissions around the mid-century. “Blue” hydrogen from natural gas with CO2 capture and storage (CCS) is one promising sustainable hydrogen supply option. Although conventional CO2 capture imposes a large energy penalty advanced process concepts using the chemical looping principle can produce blue hydrogen at efficiencies even exceeding the conventional steam methane reforming (SMR) process without CCS. One such configuration is gas switching reforming (GSR) which uses a Ni-based oxygen carrier material to catalyze the SMR reaction and efficiently supply the required process heat by combusting an off-gas fuel with integrated CO2 capture. The present study investigates the potential of advanced La-Fe-based oxygen carrier materials to further increase this advantage using a gas switching partial oxidation (GSPOX) process. These materials can overcome the equilibrium limitations facing conventional catalytic SMR and achieve direct hydrogen production using a water-splitting reaction. Results showed that the GSPOX process can achieve mild efficiency improvements relative to GSR in the range of 0.6–4.1%-points with the upper bound only achievable by large power and H2 co-production plants employing a highly efficient power cycle. These performance gains and the avoidance of toxicity challenges posed by Ni-based oxygen carriers create a solid case for the further development of these advanced materials. If successful results from this work indicate that GSPOX blue hydrogen plants can outperform an SMR benchmark with conventional CO2 capture by more than 10%-points both in terms of efficiency and CO2 avoidance.
Pathway to Net Zero Emissions
Oct 2021
Publication
A feasible path to limit planetary warming to 1.5°C requires certain countries and sectors to go below net zero and to do so well before the middle of the century according to new analysis from the authors of the Energy Transition Outlook. DNV’s pathway to net zero says North America and Europe must be carbon neutral by 2042 whereas Indian Subcontinent is set to be a net emitter by 2050 Net zero report says carbon capture storage and use is required as energy production will not be carbon neutral by 2050 Aim to halve emissions by 2030 is out of reach but massive early action is needed if we are to have any chance of reaching a 1.5°C future DNV’s new report “Pathway to Net Zero Emissions” describes a feasible way to limit global warming to 1.5°C Policy makers are set to meet in Glasgow for the COP 26 summit with an eye on achieving zero emissions by 2050. For this to happen North America and Europe must be carbon neutral by 2042 and then carbon negative thereafter according to DNV’s pathway to net zero. The pathway also finds that Greater China must reduce emissions by 98% from 2019 levels by 2050. There are regions that cannot realistically transition completely away from fossil fuels in the same timeframe such as the Indian Subcontinent which will reduce emissions by 64%. Pathway to Net Zero Emissions also lays out the pace at which different industry sectors need to decarbonize. The so-called hard-to-abate sectors will take longer to decarbonize and even if sectors like maritime (-90% CO2 emissions in 2050) and iron and steel production (-82%) scale up the introduction of greener technologies they will still be net emitters by 2050.
A Review on the Properties of Iron Aluminide Intermetallics
Jan 2016
Publication
Iron aluminides have been among the most studied intermetallics since the 1930s when their excellent oxidation resistance was first noticed. Their low cost of production low density high strength-to-weight ratios good wear resistance ease of fabrication and resistance to high temperature oxidation and sulfurization make them very attractive as a substitute for routine stainless steel in industrial applications. Furthermore iron aluminides allow for the conservation of less accessible and expensive elements such as nickel and molybdenum. These advantages have led to the consideration of many applications such as brake disks for windmills and trucks filtration systems in refineries and fossil power plants transfer rolls for hot-rolled steel strips and ethylene crackers and air deflectors for burning high-sulfur coal. A wide application for iron aluminides in industry strictly depends on the fundamental understanding of the influence of (i) alloy composition; (ii) microstructure; and (iii) number (type) of defects on the thermo-mechanical properties. Additionally environmental degradation of the alloys consisting of hydrogen embrittlement anodic or cathodic dissolution localized corrosion and oxidation resistance in different environments should be well known. Recently some progress in the development of new micro- and nano-mechanical testing methods in addition to the fabrication techniques of micro- and nano-scaled samples has enabled scientists to resolve more clearly the effects of alloying elements environmental items and crystal structure on the deformation behavior of alloys. In this paper we will review the extensive work which has been done during the last decades to address each of the points mentioned above.
Heat to Hydrogen by RED—Reviewing Membranes and Salts for the RED Heat Engine Concept
Dec 2021
Publication
The Reverse electrodialysis heat engine (REDHE) combines a reverse electrodialysis stack for power generation with a thermal regeneration unit to restore the concentration difference of the salt solutions. Current approaches for converting low-temperature waste heat to electricity with REDHE have not yielded conversion efficiencies and profits that would allow for the industrialization of the technology. This review explores the concept of Heat-to-Hydrogen with REDHEs and maps crucial developments toward industrialization. We discuss current advances in membrane development that are vital for the breakthrough of the RED Heat Engine. In addition the choice of salt is a crucial factor that has not received enough attention in the field. Based on ion properties relevant for both the transport through IEMs and the feasibility for regeneration we pinpoint the most promising salts for use in REDHE which we find to be KNO3 LiNO3 LiBr and LiCl. To further validate these results and compare the system performance with different salts there is a demand for a comprehensive thermodynamic model of the REDHE that considers all its units. Guided by such a model experimental studies can be designed to utilize the most favorable process conditions (e.g. salt solutions).
Process Integration of Green Hydrogen: Decarbonization of Chemical Industries
Sep 2020
Publication
Integrated water electrolysis is a core principle of new process configurations for decarbonized heavy industries. Water electrolysis generates H2 and O2 and involves an exchange of thermal energy. In this manuscript we investigate specific traditional heavy industrial processes that have previously been performed in nitrogen-rich air environments. We show that the individual process streams may be holistically integrated to establish new decarbonized industrial processes. In new process configurations CO2 capture is facilitated by avoiding inert gases in reactant streams. The primary energy required to drive electrolysis may be obtained from emerging renewable power sources (wind solar etc.) which have enjoyed substantial industrial development and cost reductions over the last decade. The new industrial designs uniquely harmonize the intermittency of renewable energy allowing chemical energy storage. We show that fully integrated electrolysis promotes the viability of decarbonized industrial processes. Specifically new process designs uniquely exploit intermittent renewable energy for CO2 conversion enabling thermal integration H2 and O2 utilization and sub-process harmonization for economic feasibility. The new designs are increasingly viable for decarbonizing ferric iron reduction municipal waste incineration biomass gasification fermentation pulp production biogas upgrading and calcination and are an essential step forward in reducing anthropogenic CO2 emissions.
A Review of Cohesive Zone Modelling as an Approach for Numerically Assessing Hydrogen Embrittlement of Steel Structures
Jun 2014
Publication
Simulation of hydrogen embrittlement (HE) requires a coupled approach; on one side the models describing hydrogen transport must account for local mechanical fields while on the other side the effect of hydrogen on the accelerated material damage must be implemented into the model describing crack initiation and growth. This study presents a review of coupled diffusion and cohesive zone modelling as a method for numerically assessing HE of a steel structure. While the model is able to reproduce single experimental results by appropriate fitting of the cohesive parameters there appears to be limitations in transferring these results to other hydrogen systems. Agreement may be improved by appropriately identifying the required input parameters for the particular system under study.
Link to document download on Royal Society Website
Link to document download on Royal Society Website
Decarbonization Synergies From Joint Planning of Electricity and Hydrogen Production: A Texas Case Study
Oct 2020
Publication
Hydrogen (H2) shows promise as an energy carrier in contributing to emissions reductions from sectors which have been difficult to decarbonize like industry and transportation. At the same time flexible H2 production via electrolysis can also support cost-effective integration of high shares of variable renewable energy (VRE) in the power system. In this work we develop a least-cost investment planning model to co-optimize investments in electricity and H2 infrastructure to serve electricity and H2 demands under various low-carbon scenarios. Applying the model to a case study of Texas in 2050 we find that H2 is produced in approximately equal amounts from electricity and natural gas under the least-cost expansion plan with a CO2 price of $30–60/tonne. An increasing CO2 price favors electrolysis while increasing H2 demand favors H2 production from Steam Methane Reforming (SMR) of natural gas. H2 production is found to be a cost effective solution to reduce emissions in the electric power system as it provides flexibility otherwise provided by natural gas power plants and enables high shares of VRE with less battery storage. Additionally the availability of flexible electricity demand via electrolysis makes carbon capture and storage (CCS) deployment for SMR cost-effective at lower CO2 prices ($90/tonne CO2) than for power generation ($180/tonne CO2 ). The total emissions attributable to H2 production is found to be dependent on the H2 demand. The marginal emissions from H2 production increase with the H2 demand for CO2 prices less than $90/tonne CO2 due to shift in supply from electrolysis to SMR. For a CO2 price of $60/tonne we estimate the production weighted-average H2 price to be between $1.30–1.66/kg across three H2 demand scenarios. These findings indicate the importance of joint planning of electricity and H2 infrastructure for cost-effective energy system decarbonization.
Concept of Hydrogen Fired Gas Turbine Cycle with Exhaust Gas Recirculation: Assessment of Process Performance
Nov 2019
Publication
High hydrogen content fuels can be used in gas turbine for power generation with CO2 capture IGCC plants or with hydrogen from renewables. The challenge for the engine is the high reactive combustion properties making dilution necessary to mitigate NOx emissions at the expense of a significant energy cost. In the concept analysed in this study high Exhaust Gas Recirculation (EGR) rate is applied to the gas turbine to generate oxygen depleted air. As a result combustion temperature is inherently limited keeping NOx emissions low without the need for dilution or unsafe premixing. The concept is analysed by process simulation based on a reference IGCC plant with CO2 Capture. Results with dry and wet EGR options are presented as a function EGR rate. Efficiency performance is assessed against the reference power cycle with nitrogen dilution. All EGR options are shown to represent an efficiency improvement. Nitrogen dilution is found to have a 1.3% efficiency cost. Although all EGR options investigated offer an improvement dry EGR is considered as the preferred option despite the need for higher EGR rate as compared with the wet EGR. The efficiency gain is calculated to be of 1% compared with the reference case.
Experimental Study of Light Gas Dispersion in a Channel
Sep 2019
Publication
Usage of hydrogen as fuel gives rise to possible accidental risks due to leakage and dispersion. A risk from hydrogen leak is the formation of a large volume of the hydrogen-air mixture which could be ignited and leading up to a severe explosion. Prevention and control of formation and ignition of combustible hydrogen cloud necessitate sufficient knowledge of mechanisms of the hydrogen leak dispersion ignition and over-pressures generated during combustion. This paper aims to investigate the momentum-controlled jet the buoyancy-controlled wave and the parameters influencing hydrogen concentration distribution in an elongated space. It demonstrates experimental results and analysis from helium and hydrogen dispersion in a channel. A set of experiments were carried out for the release of helium and hydrogen jets in a 3 m long channel to record their concentrations in the cloud by concentration sensors at different horizontal and vertical positions. Flow visualization technique was applied using shadowgraph to image the mixing process next to the release point and the helium- hydrogen-air cloud shape at the middle of the channel. Moreover results were used for comparison of helium and hydrogen concentration gradients. The results of the experiments show that swift mixing occurs at higher flow rates smaller nozzle sizes and downward release direction. Higher concentration recorded in the channel with negative inclination. Results also confirmed that hydrogen/helium behavior pattern in the channel accords with mutual intrusion theory about gravity currents.
Pressure Peaking Phenomena: Unignited Hydrogen Releases in Confined Spaces – Large-scale Experiments
Sep 2020
Publication
The aim of this study was to validate a model for predicting overpressure arising from accidental hydrogen releases in areas with limited ventilation. Experiments were performed in a large-scale setup that included a steel-reinforced container of volume 14.9 m3 and variable ventilation areas and mass flow rates. The pressure peaking phenomenon characterized as transient overpressure with a characteristic peak in a vented enclosure was observed during all the experiments. The model description presented the relationship between the ventilation area mass flow rate enclosure volume and discharge coefficient. The experimental results were compared with two prediction models representing a perfect mix and the real mix. The perfect mix assumed that all the released hydrogen was well stirred inside the enclosure during the releases. The real mix prediction s used the hydrogen concentration and temperature data measured during experiments. The prediction results with both perfect mix and real mix showed possible hazards during unignited hydrogen releases.
Integration of Gas Switching Combustion and Membrane Reactors for Exceeding 50% Efficiency in Flexible IGCC Plants with Near-zero CO2 Emissions
Jul 2020
Publication
Thermal power plants face substantial challenges to remain competitive in energy systems with high shares of variable renewables especially inflexible integrated gasification combined cycles (IGCC). This study addresses this challenge through the integration of Gas Switching Combustion (GSC) and Membrane Assisted Water Gas Shift (MAWGS) reactors in an IGCC plant for flexible electricity and/or H2 production with inherent CO2 capture. When electricity prices are high H2 from the MAWGS reactor is used for added firing after the GSC reactors to reach the high turbine inlet temperature of the H-class gas turbine. In periods of low electricity prices the turbine operates at 10% of its rated power to satisfy the internal electricity demand while a large portion of the syngas heating value is extracted as H2 in the MAWGS reactor and sold to the market. This product flexibility allows the inflexible process units such as gasification gas treating air separation unit and CO2 compression transport and storage to operate continuously while the plant supplies variable power output. Two configurations of the GSC-MAWGS plant are presented. The base configuration achieves 47.2% electric efficiency and 56.6% equivalent hydrogen production efficiency with 94.8–95.6% CO2 capture. An advanced scheme using the GSC reduction gases for coal-water slurry preheating and pre-gasification reached an electric efficiency of 50.3% hydrogen efficiency of 62.4% and CO2 capture ratio of 98.1–99.5%. The efficiency is 8.4%-points higher than the pre-combustion CO2 capture benchmark and only 1.9%-points below the unabated IGCC benchmark.
Integration of Chemical Looping Combustion for Cost-effective CO2 Capture from State-of-the-art Natural Gas Combined Cycles
May 2020
Publication
Chemical looping combustion (CLC) is a promising method for power production with integrated CO2 capture with almost no direct energy penalty. When integrated into a natural gas combined cycle (NGCC) plant however CLC imposes a large indirect energy penalty because the maximum achievable reactor temperature is far below the firing temperature of state-of-the-art gas turbines. This study presents a techno-economic assessment of a CLC plant that circumvents this limitation via an added combustor after the CLC reactors. Without the added combustor the energy penalty amounts to 11.4%-points causing a high CO2 avoidance cost of $117.3/ton which is more expensive than a conventional NGCC plant with post-combustion capture ($93.8/ton) with an energy penalty of 8.1%-points. This conventional CLC plant would also require a custom gas turbine. With an added combustor fired by natural gas a standard gas turbine can be deployed and CO2 avoidance costs are reduced to $60.3/ton mainly due to a reduction in the energy penalty to only 1.4%-points. However due to the added natural gas combustion after the CLC reactor CO2 avoidance is only 52.4%. Achieving high CO2 avoidance requires firing with clean hydrogen instead increasing the CO2 avoidance cost to $96.3/ton when a hydrogen cost of $15.5/GJ is assumed. Advanced heat integration could reduce the CO2 avoidance cost to $90.3/ton by lowering the energy penalty to only 0.6%-points. An attractive alternative is therefore to construct the plant for added firing with natural gas and retrofit the added combustor for hydrogen firing when CO2 prices reach very high levels.
Large Scale Experiments and Model Validation of Pressure Peaking Phenomena-ignited Hydrogen Releases
Jan 2021
Publication
The Pressure Peaking Phenomena (PPP) is the effect of introducing a light gas into a vented volume of denser gas. This will result in a nonequilibrium pressure as the light gas pushes the dense gas out at the vent. Large scale experiments have been performed to produce relevant evidence. The results were used to validate an analytical model. Pressure and temperature were measured inside a constant volume while the mass flow and vent area were varied. The analytical model was based on the conservation of mass and energy. The results showed that increasing the mass flow rate the peak pressure increases and with increasing the ventilation area the peak pressure decreases. Peak pressure was measured above 45 kPa. Longer combustion time resulted in higher temperatures increasing an underpressure effect. The experimental results showed agreement with the analytical model results. The model predicts the pressures within reasonable limits of+/-2 kPa. The pressure peaking phenomena could be very relevant for hydrogen applications in enclosures with limited ventilation. This could include car garages ship hull compartments as well as compressor shielding. This work shows that the effect can be modeled and results can be used in design to reduce the consequences.
Mathematical Modeling and Simulation of Hydrogen-fueled Solid Oxide Fuel Cell System for Micro-grid Applications - Effect of Failure and Degradation on Transient Performance
May 2020
Publication
We use a detailed solid oxide fuel cell (SOFC) model for micro-grid applications to analyze the effect of failure and degradation on system performance. Design and operational constraints on a component and system level are presented. A degrees of freedom analysis identifies controlled and manipulated system variables which are important for control. Experimental data are included to model complex degradation phenomena of the SOFC unit. Rather than using a constant value a spatially distributed degradation rate as function of temperature and current density is used that allows to study trajectory based performance deterioration. The SOFC unit is assumed to consist of multiple stacks. The failure scenario studied is the loss of one individual SOFC stack e.g. due to breakage of sealing or a series of fuel cells. Simulations reveal that degradation leads to significant drifts from the design operating point. Moreover failure of individual stacks may bring the still operating power generation unit into a regime where further failures and accelerated degradation is more likely. It is shown that system design dimensioning operation and control are strongly linked. Apart from specific quantitative results perhaps the main practical contribution are the collected constraints and the degrees of freedom analysis.
On Capital Utilization in the Hydrogen Economy: The Quest to Minimize Idle Capacity in Renewables-rich Energy Systems
Oct 2020
Publication
The hydrogen economy is currently experiencing a surge in attention partly due to the possibility of absorbing variable renewable energy (VRE) production peaks through electrolysis. A fundamental challenge with this approach is low utilization rates of various parts of the integrated electricity-hydrogen system. To assess the importance of capacity utilization this paper introduces a novel stylized numerical energy system model incorporating the major elements of electricity and hydrogen generation transmission and storage including both “green” hydrogen from electrolysis and “blue” hydrogen from natural gas reforming with CO2 capture and storage (CCS). Concurrent optimization of all major system elements revealed that balancing VRE with electrolysis involves substantial additional costs beyond reduced electrolyzer capacity factors. Depending on the location of electrolyzers greater capital expenditures are also required for hydrogen pipelines and storage infrastructure (to handle intermittent hydrogen production) or electricity transmission networks (to transmit VRE peaks to electrolyzers). Blue hydrogen scenarios face similar constraints. High VRE shares impose low utilization rates of CO2 capture transport and storage infrastructure for conventional CCS and of hydrogen transmission and storage infrastructure for a novel process (gas switching reforming) that enables flexible power and hydrogen production. In conclusion all major system elements must be considered to accurately reflect the costs of using hydrogen to integrate higher VRE shares.
The Case for High-pressure PEM Water Electrolysis
Apr 2022
Publication
Hydrogen compression is a key part of the green hydrogen supply chain but mechanical compressors are prone to failure and add system complexity and cost. High-pressure water electrolysis can alleviate this problem through electrochemical compression of the gas internally in the electrolyzer and thereby eliminating the need for an external hydrogen compressor. In this work a detailed techno-economic assessment of high-pressure proton exchange membrane-based water electrolysis (PEMEL) systems was carried out. Electrolyzers operating at 80 200 350 and 700 bar were compared to state-of-the-art systems operating at 30 bar in combination with a mechanical compressor. The results show that it is possible to achieve economically viable solutions with high-pressure PEMEL-systems operating up to 200 bar. These pressure levels fit well with the requirements in existing and future industrial applications such as e-fuel production (30–120 bar) injection of hydrogen into natural gas grids (70 bar) hydrogen gas storage (≥200 bar) and ammonia production (200–300 bar). A sensitivity analysis also showed that if the cost of electricity is sufficiently low (
Features of the Hydrogen-Assisted Cracking Mechanism in the Low-Carbon Steel at Ex- and In-situ Hydrogen Charging
Dec 2018
Publication
Hydrogen embrittlement has been intensively studied in the past. However its governing mechanism is still under debate. Particularly the details of the formation of specific cleavage-like or quasi-cleavage fracture surfaces related to hydrogen embrittled steels are unclear yet. Recently it has been found that the fracture surface of the hydrogen charged and tensile tested low-carbon steel exhibits quasi-cleavage facets having specific smoothly curved surface which is completely different from common flat cleavage facets. In the present contribution we endeavor to shed light on the origin of such facets. For this purpose the notched flat specimens of the commercial low carbon steel were tensile tested using ex- and in-situ hydrogen charging. It is found that in the ex-situ hydrogen charged specimens the cracks originate primarily inside the specimen bulk and expand radially form the origin to the specimen surface. This process results in formation of “fisheyes” – the round-shape areas with the surface composed of curved quasi-cleavage facets. In contrast during tensile testing with in-situ hydrogen charging the cracks initiate from the surface and propagate to the bulk. This process results in the formation of the completely brittle fracture surface with the quasi-cleavage morphology - the same as that in fisheyes. The examination of the side surface of the in-situ hydrogen charged specimens revealed the straight and S-shaped sharp cracks which path is visually independent of the microstructure and crystallography but is strongly affected by the local stress fields. Nano-voids are readily found at the tips of these cracks. It is concluded that the growth of such cracks occurs by the nano-void coalescence mechanism and is responsible for the formation of fisheyes and smoothly curved quasi-cleavage facets in hydrogen charged low-carbon steel.
High-pressure PEM Water Electrolyser Performance Up to 180 Bar Differential Pressure
Feb 2024
Publication
Proton exchange membrane (PEM) electrolysers (PEMEL) are key for converting and storing excess renewable energy. PEMEL water electrolysis offers benefits over alkaline water electrolysers including a large dynamic range high responsiveness and high current densities and pressures. High operating pressures are important because it contributes to reduce the costs and energy-use related to downstream mechanical compression. In this work the performance of a high-pressure PEMEL system has been characterized up to 180 bar. The electrolyser stack has been characterized with respect to electrochemical performance net H2 production rate and water crossover and the operability and performance of the thermal- and gas management systems of the test bench has been assessed. The tests show that the voltage increase upon pressurization from 5 to 30 bar is 30 % smaller than expected but further pressurization reduces performance. The study confirms that highpressure PEMEL has higher energy consumption than state-of-the-art electrolyser systems with mechanical compressors. However there can be a business case for high-pressure PEMEL if the trade-off between stack efficiency and system efficiency is balanced.
Hydrogen Venting Under Variable Flow Conditions
Sep 2011
Publication
Safety distances for hydrogen plumes are currently derived using models developed for hydrocarbon releases. It is well known that hydrogen behaves in a significantly different manner to that of hydrocarbons when released to atmosphere. There are two main aspects involved with the development of safety distances for credible hydrogen releases; the intensity of the thermal radiation from such a plume should it be ignited and the distance downwind from the release point to the point where a flammable mixture with air no longer exists. A number of distinct areas of venting behaviour were investigated; Thermal radiation from ignited plumes from vertical open ended vent pipes Far field radiation measurements for direct comparison with models Thermal radiation from ignited plumes from vertical vent pipes terminating in a T-piece Thermal radiation measurements from ignited hydrogen with a 45 vent termination Hydrogen concentration measurements with a T-piece.
A Study of Hydrogen Flame Length with Complex Nozzle Geometry
Sep 2017
Publication
The growing number of hydrogen fillings stations and cars increases the need for accurate models to determine risk. The effect on hydrogen flame length was measured by varying the diameter of the spouting nozzle downstream from the chocked nozzle upstream. The results was compared with an existing model for flame length estimations. The experimental rig was setup with sensors that measured accurately temperature mass flow heat radiation and the pressure range from 0.1 to 11 MPa. The flame length was determined with an in-house developed image-processing tool which analyzed a high-speed film of the each experiment. Results show that the nozzle geometry can cause a deviation as high as 50% compared to estimated flame lengths by the model if wrong assumptions are made. Discharge coefficients for different nozzles has been calculated and presented.
Consequence Models for Vented Hydrogen Deflagrations: CFD vs. Engineering Models
Sep 2017
Publication
This paper compares two approaches for predicting the consequences of vented hydrogen deflagrations: empirical engineering models (EMs) and computational fluid dynamics (CFD) simulations. The study is part of the project ‘Improving hydrogen safety for energy applications through pre-normative research on vented deflagrations’ (HySEA) funded by the Fuel Cells and Hydrogen 2 Joint Undertaking (FCH JU) under grant agreement No 671461. The HySEA project focuses on vented hydrogen deflagrations in containers and smaller enclosures with internal congestion representative of industrial applications. Data from experiments conducted as part of the HySEA project are used to evaluate predictions from a selection of EMs and the CFD tool FLACS. The experiments involve various obstacle and venting configurations and initially quiescent homogeneous hydrogen-air mixtures with hydrogen concentrations in the range 15–24 vol%. There is a significant scatter in the maximum reduced overpressures predicted by the different EMs in the present study. For certain configurations there is an order of magnitude difference between the different EM predictions. Two versions of the CFD tool FLACS are used in the present study: i) the standard commercial release FLACS v10.7r2 and ii) an in-house development version termed FLACS-beta. The commercial release generally over-predicts the maximum overpressures measured in the experiments while the development version of FLACS gives improved results for several configurations.
Implementing Maritime Battery-electric and Hydrogen Solutions: A Technological Innovation Systems Analysis
Sep 2020
Publication
Maritime transport faces increasing pressure to reduce its greenhouse gas emissions to be in accordance with the Paris Agreement. For this to happen low- and zero-carbon energy solutions need to be developed. In this paper we draw on sustainability transition literature and introduce the technological innovation system (TIS) framework to the field of maritime transportation research. The TIS approach analytically distinguishes between different innovation system functions that are important for new technologies to develop and diffuse beyond an early phase of experimentation. This provides a basis for technology-specific policy recommendations. We apply the TIS framework to the case of battery-electric and hydrogen energy solutions for coastal maritime transport in Norway. Whereas both battery-electric and hydrogen solutions have developed rapidly the former is more mature and has a strong momentum. Public procurement and other policy instruments have been crucial for developments to date and will be important for these technologies to become viable options for shipping more generally.
The Effect of Hydrogen on the Nanoindentation Behavior of Heat Treated 718 Alloy
Oct 2020
Publication
In this study the effect of precipitates on the surface mechanical properties in the presence of hydrogen (H) is investigated by in situ electrochemical nanoindentation. The nickel superalloy 718 is subjected to three different heat treatments leading to different sizes of the precipitates: (i) solution annealing (SA) to eliminate all precipitates (ii) the as-received (AR) sample with fine dispersed precipitates and (iii) the over-aged (OA) specimen with coarser precipitates. The nanoindentation is performed using a conical tip and a new method of reverse imaging is employed to calculate the nano-hardness. The results show that the hardness of the SA sample is significantly affected by H diffusion. However it could be recovered by removing the H from its matrix by applying an anodic potential. Since the precipitates in the OA and AR samples are different they are influenced by H differently. The hardness increase for the OA sample is more significant in −1200mV while for the AR specimen the H is more effective in −1500mV. In addition the pop-in load is reduced when the samples are exposed to cathodic charging and it cannot be fully recovered by switching to an anodic potential.
Palladium (Pd) Membranes as Key Enabling Technology for Pre-combustion CO2 Capture and Hydrogen Production
Aug 2017
Publication
Palladium (Pd) membranes are a promising enabling technology for power generation and hydrogen production with CO2 capture. SINTEF has developed and patented a flexible technology to produce Pd-alloy membranes that significantly improves flux and thereby reduces material costs. Reinertsen AS and SINTEF aim to demonstrate the Pd membrane technology for H2 separation on a side stream of the Statoil Methanol Plant at Tjeldbergodden Norway. In the present article we present the upscaling of the membrane manufacturing process together with the membrane module and skid design and construction.
Balancing GHG Mitigation and Land-use Conflicts: Alternative Northern European Energy System Scenarios
Jan 2022
Publication
Long-term power market outlooks suggest a rapid increase in renewable energy deployment as a main solution to greenhouse gas mitigation in the Northern European energy system. However the consequential area requirement is a non-techno-economic aspect that currently is omitted by many energy system optimization models. This study applies modeling to generate alternatives (MGA) technique to the Balmorel energy system model to address spatial conflicts related to increased renewable energy deployment. The approach searches for alternative solutions that minimize land-use conflicts while meeting the low-carbon target by allowing a 1% to 15% increase in system costs compared to the least-cost solution. Two alternative objectives are defined to reflect various aspects of spatial impact. The results show that the least-cost solution requires 1.2%–3.6% of the land in the modeled countries in 2040 for onshore wind and solar PV installations. A 10% increase in costs can reduce the required land area by 58% by relying more on offshore wind. Nuclear energy may also be an option if both onshore and offshore areas are to be reduced or in a less flexible system. Both offshore wind and nuclear energy technologies are associated with higher risks and pose uncertainties in terms of reaching the climate targets in time. The changes in costs and required land areas imply significantly higher annual costs ranging from 200 to 750 kEUR/km2 to avoid land use for energy infrastructure. Overall this study confirms that the energy transition strategies prioritizing land savings from energy infrastructure are feasible but high risks and costs of averted land are involved.
The Use of Metal Hydrides in Fuel Cell Applications
Feb 2017
Publication
This paper reviews state-of-the-art developments in hydrogen energy systems which integrate fuel cells with metal hydride-based hydrogen storage. The 187 reference papers included in this review provide an overview of all major publications in the field as well as recent work by several of the authors of the review. The review contains four parts. The first part gives an overview of the existing types of fuel cells and outlines the potential of using metal hydride stores as a source of hydrogen fuel. The second part of the review considers the suitability and optimisation of different metal hydrides based on their energy efficient thermal integration with fuel cells. The performances of metal hydrides are considered from the viewpoint of the reversible heat driven interaction of the metal hydrides with gaseous H2. Efficiencies of hydrogen and heat exchange in hydrogen stores to control H2 charge/discharge flow rates are the focus of the third section of the review and are considered together with metal hydride – fuel cell system integration issues and the corresponding engineering solutions. Finally the last section of the review describes specific hydrogen-fuelled systems presented in the available reference data.
A Barrier Analysis of a Generic Hydrogen Refuelling Station
Sep 2009
Publication
Any technical installation need appropriate safety barriers installed to prevent or mitigate any adverse effects concerning people property and environment. In this context a safety barrier is a series of elements each consisting of a technical system or human action that implement a planned barrier function to prevent control or mitigate the propagation of a condition or event into an undesired condition or event. This is also important for new technologies as hydrogen refuelling stations being operated at very high pressures up to 900bar. In order to establish the needed barriers a hazard identification of the installation has to be carried out to identify the possible hazardous events. In this study this identification was done using the generic layout of a future large hydrogen refuelling station that has been developed by the EU NoE HySafe. This was based on experiences with smaller scale refuelling stations that has been in operation for several years e.g. being used in the former CUTE and ECTOS projects. Using this approach the object of the study is to support activities to further improve the safety performance of future larger refuelling stations. This will again help to inform the authorities and the public to achieve a proper public awareness and to support building up a realistic risk and safety perception of the safety on such future refuelling stations. In the second step the hazardous events that may take place and the barriers installed to stop hazards and their escalation are analysed also using in-house developed software to model the barriers and to quantify their performance. The paper will present an overview and discuss the state-of-the-art of the barriers established in the generic refuelling station.
Materials Considerations in Hydrogen Production
Sep 2007
Publication
Correct selection and application of materials is essential to ensure safety and economy in production transportation and storage of hydrogen. There are several sources of materials challenges related to hydrogen. Established component producers may have limited experience in this specific field. Process developments may involve new process conditions with new demands on the materials. Further new materials will be added to the engineering toolbox to be used. The behaviour of these materials for hydrogen service may need additional documentation. Finally focus on hydrogen susceptibility and hydrogen damages alone may take away awareness of other subjects as trace elements by-products and change in raw materials which may be of as high importance for safety and quality. This overview of challenges and recommendations is made with emphasis on water electrolysis.
Dynamic Load Analysis of Explosion in Inhomogeneous Hydrogen-air Mixtures
Sep 2017
Publication
This paper presents results from experiments on gas explosions in inhomogeneous hydrogen-air mixtures. The experimental channel is 3 m with a cross section of 100 mm by 100 mm and a 0.25 mm ID nozzle for hydrogen release into the channel. The channel is open in one end. Spectral analysis of the pressure in the channel is used to determine dynamic load factors for SDOF structures. The explosion pressures in the channel will fluctuate with several frequencies or modes and a theoretical high DLF is seen when the pressure frequencies and eigen frequencies of the structure matches.
Enhancing the Efficiency of Power- and Biomass-to-liquid Fuel Processes Using Fuel-assisted Solid Oxide Electrolysis Cells
Apr 2022
Publication
Power- and biomass-to-liquid fuel processes (PBtL) can utilize renewable energy and residual forestry waste to produce liquid synthetic fuels which have the potential to mitigate the climate impacts of the current transportation infrastructure including the long-haul aviation sector. In a previous study we demonstrated that implementing a solid oxide electrolysis cell (SOEC) in the PBtL process can significantly increase the energy efficiency of fuel production by supplying the produced hydrogen to a reverse water gas shift (RWGS) reactor to generate syngas which is then fed downstream to a Fischer–Tropsch (FT) reactor. The tail gas emitted from the FT reactor consists primarily of a mixture of hydrogen carbon monoxide and methane and is often recycled to the entrained flow gasifier located at the beginning of the process. In this analysis we investigate the efficiency gains of the PBtL process as a result of redirecting the tail gas of the FT reactor to the anode of an SOEC to serve as fuel. Supplying fuel to an SOEC can lower the electrical work input required to facilitate steam electrolysis when reacting electrochemically with oxide ions in the anode which in turn can reduce oxygen partial pressures and thus alleviate material degradation. Accordingly we develop a thermodynamic framework to reveal the performance limits of fuel-assisted SOECs (FASOECs) and provide strategies to minimize oxygen partial pressures in the SOEC anode. Additionally we elucidate how much fuel is required to match the heating demands of a cell when steam is supplied to the cathode over a broad range of inlet temperatures and demonstrate the influence of a set of reaction pathways of the supplied fuel on the operating potential of an FASOEC and the corresponding efficiency gain of the PBtL process. Based on preliminary calculations we estimate that implementing an FASOEC in the PBtL process can increase the energy efficiency of fuel production to more than 90% depending on the amount of FT tail gas available to the system.
Heading for Hydrogen - The Oil and Gas Industry’s Outlook for Hydrogen, From Ambition to Reality
May 2020
Publication
The future of hydrogen energy is wrapped up with the future of natural gas renewable energy and carbon capture and storage (CCS). This yields useful synergies but also political economic and technical complexity. Nevertheless our survey of more than 1000 senior oil and gas professionals suggests a more certain future for hydrogen and that the time is right to begin scaling the hydrogen economy.
Vented Hydrogen Deflagrations in Containers: Effect of Congestion for Homogeneous Mixtures
Sep 2017
Publication
This paper presents results from an experimental study of vented hydrogen deflagrations in 20-foot ISO containers. The scenarios investigated include 14 tests with explosion venting through the doors of the containers and 20 tests with venting through openings in the roof. The parameters investigated include hydrogen concentration vent area type of venting device and the level of congestion inside the containers. All tests involved homogeneous and initially quiescent hydrogen-air mixtures. The results demonstrate the strong effect of congestion on the maximum reduced explosion pressures which typically is not accounted for in current standards and guidelines for explosion protection. The work is a deliverable from work package 2 (WP2) in the project “Improving hydrogen safety for energy applications through pre-normative research on vented deflagrations” or HySEA which receives funding from the Fuel Cells and Hydrogen Joint Undertaking (FCH JU) under grant agreement no. 671461.
Probability of Occurrence of ISO 14687-2 Contaminants in Hydrogen: Principles and Examples from Steam Methane Reforming and Electrolysis (Water and Chlor-alkali) Production Processes Model
Apr 2018
Publication
According to European Directive 2014/94/EU hydrogen providers have the responsibility to prove that their hydrogen is of suitable quality for fuel cell vehicles. Contaminants may originate from hydrogen production transportation refuelling station or maintenance operation. This study investigated the probability of presence of the 13 gaseous contaminants (ISO 14687-2) in hydrogen on 3 production processes: steam methane reforming (SMR) process with pressure swing adsorption (PSA) chlor-alkali membrane electrolysis process and water proton exchange membrane electrolysis process with temperature swing adsorption. The rationale behind the probability of contaminant presence according to process knowledge and existing barriers is highlighted. No contaminant was identified as possible or frequent for the three production processes except oxygen (frequent for chlor-alkali membrane process) carbon monoxide (frequent) and nitrogen (possible) for SMR with PSA. Based on it a hydrogen quality assurance plan following ISO 19880-8 can be devised to support hydrogen providers in monitoring the relevant contaminants.
Accidental Hydrogen Release in Gc-laboratory: A Case Study
Oct 2015
Publication
A 50-litre standard hydrogen gas cylinder was temporarily placed in a laboratory to supply hydrogen gas to a flame ionization detector (FID) for use in gas chromatography (GC). On 20 January 2015 the safety relief valve on the pressure regulator failed and released about 0.34 kg of hydrogen into the laboratory. The gas cloud did not ignite so there was no injury or damage. The results of a full investigation with a complete course of action and reconstruction are presented that verify the cause of the leakage and estimate the gas concentration of the dispersion and gas cloud. A preliminary simulation of the likely explosion is provided. If the gas cloud had ignited the explosion would most likely have caused significant structural damage to doors windows and possibly the walls.
No more items...