Production & Supply Chain
Process Design and Improvement for Hydrogen Production Based on Thermodynamic Analysis: Practical Application to Real-world On-site Hydrogen Refueling Stations
Sep 2023
Publication
An energy source transition is necessary to realize carbon neutrality emphasizing the importance of a hydrogen economy. The transportation sector accounted for 27% of annual carbon emissions in 2019 highlighting the increasing importance of transitioning to hydrogen vehicles and establishing hydrogen refueling stations (HRSs). In particular HRSs need to be prioritized for deploying hydrogen vehicles and developing hydrogen supply chains. Thus research on HRS is important for achieving carbon neutrality in the transportation sector. In this study we improved the efficiency and scaled up the capacity of an on-site HRS (based on steam methane reforming with a hydrogen production rate of 30 Nm3/h) in Seoul Korea. This HRS was a prototype with low efficiency and capacity. Its efficiency was increased through thermodynamic analysis and heat exchanger network synthesis. Furthermore the process was scaled up from 30 Nm3/h to 150 Nm3/h to meet future hydrogen demand. The results of exergy analysis indicated that the exergy destruction in the reforming reactor and heat exchanger accounted for 58.1% and 19.8% respectively of the total exergy destruction. Thus the process was improved by modifying the heat exchanger network to reduce the exergy losses in these units. Consequently the thermal and exergy efficiencies were increased from 75.7% to 78.6% and from 68.1% to 70.4% respectively. The improved process was constructed and operated to demonstrate its performance. The operational and simulation data were similar within the acceptable error ranges. This study provides guidelines for the design and installation of low-carbon on-site HRSs.
Preliminary Study for the Commercialization of a Electrochemical Hydrogen Compressor
Mar 2023
Publication
A global energy shift to a carbon‐neutral society requires clean energy. Hydrogen can accelerate the process of expanding clean and renewable energy sources. However conventional hydrogen compression and storage technology still suffers from inefficiencies high costs and safety concerns. An electrochemical hydrogen compressor (EHC) is a device similar in structure to a water electrolyzer. Its most significant advantage is that it can accomplish hydrogen separation and compression at the same time. With no mechanical motion and low energy consumption the EHC is the key to future hydrogen compression and purification technology breakthroughs. In this study the compression performance efficiency and other related parameters of EHC are investigated through experiments and simulation calculations. The experimental results show that under the same experimental conditions increasing the supply voltage and the pressure in the anode chamber can improve the reaction rate of EHC and balance the pressure difference between the cathode and anode. The presence of residual air in the anode can impede the interaction between hydrogen and the catalyst as well as the proton exchange membrane (PEM) resulting in a decrease in performance. In addition it was found that a single EHC has a better compression ratio and reaction rate than a double EHC. The experimental results were compatible with the theoretical calculations within less than a 7% deviation. Finally the conditions required to reach commercialization were evaluated using the theoretical model.
Anion Exchange Membrane Water Electrolyzer: Electrode Design, Lab-scaled Testing System and Performance Evaluation
Aug 2022
Publication
Green hydrogen produced by water electrolysis is one of the most promising technologies to realize the efficient utilization of intermittent renewable energy and the decarbonizing future. Among various electrolysis technologies the emerging anion-exchange membrane water electrolysis (AEMWE) shows the most potential for producing green hydrogen at a competitive price. In this review we demonstrate a comprehensive introduction to AEMWE including the advanced electrode design the lab-scaled testing system establishment and the electrochemical performance evaluation. Specifically recent progress in developing high activity transition metal-based powder electrocatalysts and self-supporting electrodes for AEMWE is summarized. To improve the synergistic transfer behaviors between electron charge water and gas inside the gas diffusion electrode (GDE) two optimizing strategies are concluded by regulating the pore structure and interfacial chemistry. Moreover we provide a detailed guideline for establishing the AEMWE testing system and selecting the electrolyzer components. The influences of the membrane electrode assembly (MEA) technologies and operation conditions on cell performance are also discussed. Besides diverse electrochemical methods to evaluate the activity and stability implement the failure analyses and realize the in-situ characterizations are elaborated. In end some perspectives about the optimization of interfacial environment and cost assessments have been proposed for the development of advanced and durable AEMWE.
A Review on the Environmental Performance of Various Hydrogen Production Technologies: An Approach Towards Hydrogen Economy
Nov 2023
Publication
Demand for hydrogen has grown and continues to rise as a versatile energy carrier. Hydrogen can be produced from renewable and non-renewable energy sources. A wide range of technologies to produce hydrogen in an environmentally friendly way have been developed. As the life cycle assessment (LCA) approach has become popular recently including in the hydrogen energy system this paper comprehensively reviews the LCA of hydrogen production technology. A subdivision based on the trends in the LCA studies hydrogen production technology goal and scope definition system boundary and environmental performance of hydrogen production is discussed in this review. Thermochemical hydrogen production is the most studied technology in LCA. However utilizing natural resources especially wind power in the electrolysis process stands out as an environmentally preferable solution when compared to alternative production processes. It is crucial to rethink reactors and other production-related equipment to improve environmental performance and increase hydrogen production efficiency. Since most of the previous LCA studies were conducted in developed countries and only a few were from developing countries a way forward for LCA application on hydrogen in developing countries was also highlighted and discussed. This review provides a comprehensive insight for further research on hydrogen production technology from an LCA perspective.
A Systematic Review of the Techno-economic Assessment of Various Hydrogen Production Methods of Power Generation
Oct 2022
Publication
Hydrogen is a low or zero-carbon energy source that is considered the most promising and potential energy carrier of the future. In this study the energy sources feedstocks and various methods of hydrogen production from power generation are comparatively investigated in detail. In addition this study presents an economic assessment to evaluate cost-effectiveness based on different economic indicators including sensitivity analysis and uncertainty analysis. Proton exchange membrane fuel cell (PEMFCs) technology has the most potential to be developed compared to several other technologies. PEMFCs have been widely used in various fields and have advantages (i.e. start-up zero-emissions high power density). Among the various sources of uncertainty in the sensitivity analysis the cost estimation method shows inflationary deviations from the proposed cost of capital. This is due to the selection process and untested technology. In addition the cost of electricity and raw materials as the main factors that are unpredictable.
Feasibility Study into Water Requirement for Hydrogen Production
Nov 2022
Publication
Low carbon hydrogen can be produced by a variety of processes that require substantial quantities of water. Several major hydrogen projects are proposed in Scotland; as an energy storage medium allowing new renewable power capacity to operate and as a direct alternative to displace natural gas as a primary fuel source. The additional water consumption associated with these hydrogen projects presents an infrastructure challenge.
The aims of the study are to evaluate the water requirements of new hydrogen production facilities and the associated implications for water infrastructure and to develop a strategic framework for assessing these aspects of hydrogen projects throughout the UK. The initial focus of the study is on Scotland; however the methodology developed in the project will be used throughout the UK
Benefits
Low carbon hydrogen can be produced by a variety of processes all of which require substantial quantities of water. Several major hydrogen projects are proposed in Scotland; both as an energy storage medium allowing new renewable power capacity (particularly wind) to operate and as a direct alternative to displace natural gas as a primary fuel source. The additional water consumption associated with these hydrogen projects presents an infrastructure challenge e.g. the Scottish Environment Protection Agency (SEPA) recently highlighted Scotland’s vulnerability to dry weather and climate-induced changes in the availability and functioning of water resources.
The project in partnership with Ramboll will look to deliver a technical assessment and feasibility study into water requirements for hydrogen production in Scotland. The aims of the study are to evaluate the water requirements of new hydrogen production facilities and the associated implications for water infrastructure and to develop a strategic framework for assessing these aspects of hydrogen projects throughout the UK. The initial focus of the study is on Scotland; however the methodology developed in the project will be used throughout the UK.
The research paper can be found on their website.
The aims of the study are to evaluate the water requirements of new hydrogen production facilities and the associated implications for water infrastructure and to develop a strategic framework for assessing these aspects of hydrogen projects throughout the UK. The initial focus of the study is on Scotland; however the methodology developed in the project will be used throughout the UK
Benefits
Low carbon hydrogen can be produced by a variety of processes all of which require substantial quantities of water. Several major hydrogen projects are proposed in Scotland; both as an energy storage medium allowing new renewable power capacity (particularly wind) to operate and as a direct alternative to displace natural gas as a primary fuel source. The additional water consumption associated with these hydrogen projects presents an infrastructure challenge e.g. the Scottish Environment Protection Agency (SEPA) recently highlighted Scotland’s vulnerability to dry weather and climate-induced changes in the availability and functioning of water resources.
The project in partnership with Ramboll will look to deliver a technical assessment and feasibility study into water requirements for hydrogen production in Scotland. The aims of the study are to evaluate the water requirements of new hydrogen production facilities and the associated implications for water infrastructure and to develop a strategic framework for assessing these aspects of hydrogen projects throughout the UK. The initial focus of the study is on Scotland; however the methodology developed in the project will be used throughout the UK.
The research paper can be found on their website.
A Detailed Parametric Analysis of a Solar-Powered Cogeneration System for Electricity and Hydrogen Production
Dec 2022
Publication
Hydrogen has received increased attention in the last decades as a green energy carrier and a promising future fuel. The integration of hydrogen as well as the development of cogeneration plants makes the energy sector more eco-friendly and sustainable. The aim of this paper is the investigation of a solar-fed cogeneration system that can produce power and compressed green hydrogen. The examined unit contains a parabolic trough collector solar field a thermal energy storage tank an organic Rankine cycle and a proton exchange membrane water electrolyzer. The installation also includes a hydrogen storage tank and a hydrogen compressor. The unit is analyzed parametrically in terms of thermodynamic performance and economic viability in steady-state conditions with a developed and accurate model. Taking into account the final results the overall energy efficiency is calculated at 14.03% the exergy efficiency at 14.94% and the hydrogen production rate at 0.205 kg/h. Finally the payback period and the net present value are determined at 9 years and 122 k€ respectively.
Parametric Study and Optimization of Hydrogen Production Systems Based on Solar/Wind Hybrid Renewable Energies: A Case Study in Kuqa, China
Jan 2024
Publication
Based on the concept of sustainable development to promote the development and application of renewable energy and enhance the capacity of renewable energy consumption this paper studies the design and optimization of renewable energy hydrogen production systems. For this paper six different scenarios for grid-connected and off-grid renewable energy hydrogen production systems were designed and analyzed economically and technically and the optimal grid-connected and off-grid systems were selected. Subsequently the optimal system solution was optimized by analyzing the impact of the load data and component capacity on the grid dependency of the grid-connected hydrogen production system and the excess power rate of the off-grid hydrogen production system. Based on the simulation results the most matched load data and component capacity of different systems after optimization were determined. The grid-supplied power of the optimized grid-connected hydrogen production system decreased by 3347 kWh and the excess power rate of the off-grid hydrogen production system decreased from 38.6% to 10.3% resulting in a significant improvement in the technical and economic performance of the system.
Green with Envy? Hydrogen Production in a Carbon-constrained World
Jan 2024
Publication
Hydrogen is widely recognized as a key component of a decarbonized global energy system serving as both a fuel source and an energy storage medium. While current hydrogen production relies almost entirely on emissionsintensive processes two low-emissions production pathways – natural-gas-derived production combined with carbon capture and storage and electrolysis using carbon-free electricity – are poised to change the global supply mix. Our study assesses the financial conditions under which natural-gas-based hydrogen production combined with carbon capture and storage would be available at a cost lower than hydrogen produced through electrolysis and the degree to which these conditions are likely to arise in a transition to a net-zero world. We also assess the degree to which emissions reduction policies namely carbon pricing and carbon capture and storage tax credits affect the relative costs of hydrogen production derived from different pathways. We show that while carbon pricing can improve the relative cost of both green and blue hydrogen production compared with unabated grey hydrogen targeted tax credits favouring either blue or green hydrogen explicitly may increase emissions and/or increase the costs of the energy transition.
Coal Decarbonization: A State-of-the-art Review of Enhanced Hydrogen Production in Underground Coal Gasification
Aug 2022
Publication
The world is endowed with a tremendous amount of coal resources which are unevenly distributed in a few nations. While sustainable energy resources are being developed and deployed fossil fuels dominate the current world energy consumption. Thus low-carbon clean technologies like underground coal gasification (UCG) ought to play a vital role in energy supply and ensuring energy security in the foreseeable future. This paper provides a state-of-the-art review of the world's development of UCG for enhanced hydrogen production. It is revealed that the world has an active interest in decarbonizing the coal industry for hydrogen-oriented research in the context of UCG. While research is ongoing in multiple coal-rich nations China dominates the world's efforts in both industrial-scale UCG pilots and laboratory experiments. A variety of coal ranks were tested in UCG for enhanced hydrogen output and the possibilities of linking UCG with other prospective technologies had been proposed and critically scrutinized. Moreover it is found that transborder collaborations are in dire need to propel a faster commercialization of UCG in an ever-more carbon-conscious world. Furthermore governmental and financial support is necessary to incentivize further UCG development for large-scale hydrogen production.
Critical Mineral Demands May Limit Scaling of Green Hydrogen Production
Jan 2024
Publication
Hydrogen (H2) is widely viewed as critical to the decarbonization of industry and transportation. Water electrolysis powered by renewable electricity commonly referred to as green H2 can be used to generate H2 with low carbon dioxide emissions. Herein we analyze the critical mineral and energy demands associated with green H2 production under three different hypothetical future demand scenarios ranging from 100–1000 Mtpa H2. For each scenario we calculate the critical mineral demands required to build water electrolyzers (i.e. electrodes and electrolyte) and to build dedicated or additional renewable electricity sources (i.e. wind and solar) to power the electrolyzers. Our analysis shows that scaling electrolyzer and renewable energy technologies that use platinum group metals and rare earth elements will likely face supply constraints. Specifically larger quantities of lanthanum yttrium or iridium will be needed to increase electrolyzer capacity and even more neodymium silicon zinc molybdenum aluminum and copper will be needed to build dedicated renewable electricity sources. We find that scaling green H2 production to meet projected netzero targets will require ~24000 TWh of dedicated renewable energy generation which is roughly the total amount of solar and wind projected to be on the grid in 2050 according to some energy transition models. In summary critical mineral constraints may hinder the scaling of green H2 to meet global net-zero emissions targets motivating the need for the research and development of alternative lowemission methods of generating H2
Off-grid Wind/Hydrogen Systems with Multi-electrolyzers: Optimized Operational Strategies
Sep 2023
Publication
Optimized operation of wind/hydrogen systems can increase the system efficiency and further reduce the hydrogen production cost. In this regard extensive research has been done but there is a lack of detailed electrolyzer models and effective management of multiple electrolyzers considering their physical restrictions. This work proposes electrolyzer models that integrate the efficiency variation caused by load level change start–stop cycle (including hot and cold start) thermal management and degradation caused by frequent starts. Based on the proposed models three operational strategies are considered in this paper: two traditionally utilized methods simple start–stop and cycle rotation strategies and a newly proposed rolling optimizationbased strategy. The results from daily operation show that the new strategy results in a more balanced load level among the electrolyzers and a more stable temperature. Besides from a yearly operation perspective it is found that the proposed rolling optimization method results in more hydrogen production higher system efficiency and lower LCOH. The new method leads to hydrogen production of 311297 kg compared to 289278 kg and 303758 kg for simple start–stop and cycle rotation methods. Correspondingly the system efficiencies for the new simple start–stop and cycle rotation methods are 0.613 0.572 and 0.587. The resulting LCOH from the new method is 3.89 e/kg decreasing by 0.35 e/kg and 0.21 e/kg compared to the simple start–stop and cycle rotation methods. Finally the proposed model is compared with two conventional models to show its effectiveness in revealing more operational details and reliable results.
Experimental Study on the Performance of Controllers for the Hydrogen Gas Production Demanded by an Internal Combustion Engine
Aug 2018
Publication
This work presents the design and application of two control techniques—a model predictive control (MPC) and a proportional integral derivative control (PID) both in combination with a multilayer perceptron neural network—to produce hydrogen gas on-demand in order to use it as an additive in a spark ignition internal combustion engine. For the design of the controllers a control-oriented model identified with the Hammerstein technique was used. For the implementation of both controllers only 1% of the overall air entering through the throttle valve reacted with hydrogen gas allowing maintenance of the hydrogen–air stoichiometric ratio at 34.3 and the air–gasoline ratio at 14.6. Experimental results showed that the average settling time of the MPC controller was 1 s faster than the settling time of the PID controller. Additionally MPC presented better reference tracking error rates and standard deviation of 1.03 × 10−7 and 1.06 × 10−14 and had a greater insensitivity to measurement noise resulting in greater robustness to disturbances. Finally with the use of hydrogen as an additive to gasoline there was an improvement in thermal and combustion efficiency of 4% and 0.6% respectively and an increase in power of 545 W translating into a reduction of fossil fuel use.
Techno-economic Viability of Decentralised Solar Photovoltaic-based Green Hydrogen Production for Sustainable Energy Transition in Ghana
Feb 2024
Publication
Transition to a sustainable energy supply is essential for addressing the challenges of climate change and achieving a low-carbon future. Green hydrogen produced from solar photovoltaic (PV) systems presents a promising solution in Ghana where energy demands are increasing rapidly. The levelized cost of hydrogen (LCOH) is considered a critical metric to evaluate hydrogen production techniques cost competitiveness and economic viability. This study presents a comprehensive analysis of LCOH from solar PV systems. The study considered a 5 MW green hydrogen production plant in Ghana’s capital Accra as a proposed system. The results indicate that the LCOH is about $9.49/kg which is comparable to other findings obtained within the SubSaharan Africa region. The study also forecasted that the LCOH for solar PV-based hydrogen produced will decrease to $5–6.5/kg by 2030 and $2–2.5/kg by 2050 or lower making it competitive with fossil fuel-based hydrogen. The findings of this study highlight the potential of green hydrogen as a sustainable energy solution and its role in driving the country’s net-zero emissions agenda in relation to its energy transition targets. The study’s outcomes are relevant to policymakers researchers investors and energy stakeholders in making informed decisions regarding deploying decentralised green hydrogen technologies in Ghana and similar contexts worldwide.
Adaptive Network Fuzzy Inference System and Particle Swarm Optimization of Biohydrogen Production Process
Sep 2022
Publication
Green hydrogen is considered to be one of the best candidates for fossil fuels in the near future. Bio-hydrogen production from the dark fermentation of organic materials including organic wastes is one of the most cost-effective and promising methods for hydrogen production. One of the main challenges posed by this method is the low production rate. Therefore optimizing the operating parameters such as the initial pH value operating temperature N/C ratio and organic concentration (xylose) plays a significant role in determining the hydrogen production rate. The experimental optimization of such parameters is complex expensive and lengthy. The present research used an experimental data asset adaptive network fuzzy inference system (ANFIS) modeling and particle swarm optimization to model and optimize hydrogen production. The coupling between ANFIS and PSO demonstrated a robust effect which was evident through the improvement in the hydrogen production based on the four input parameters. The results were compared with the experimental and RSM optimization models. The proposed method demonstrated an increase in the biohydrogen production of 100 mL/L compared to the experimental results and a 200 mL/L increase compared to the results obtained using ANOVA.
Carbon-negative Hydrogen: Exploring the Techno-economic Potential of Biomass Co-gasification with CO2 Capture
Sep 2021
Publication
The hydrogen economy is receiving increasing attention as a complement to electrification in the global energy transition. Clean hydrogen production is often viewed as a competition between natural gas reforming with CO2 capture and electrolysis using renewable electricity. However solid fuel gasification with CO2 capture presents another viable alternative especially when considering the potential of biomass to achieve negative CO2 emissions. This study investigates the techno-economic potential of hydrogen production from large-scale coal/ biomass co-gasification plants with CO2 capture. With a CO2 price of 50 €/ton the benchmark plant using commercially available technologies achieved an attractive hydrogen production cost of 1.78 €/kg with higher CO2 prices leading to considerable cost reductions. Advanced configurations employing hot gas clean-up membrane-assisted water-gas shift and more efficient gasification with slurry vaporization and a chemical quench reduced the hydrogen production cost to 1.50–1.62 €/kg with up to 100% CO2 capture. Without contingencies added to the pre-commercial technologies the lowest cost reduces to 1.43 €/kg. It was also possible to recover waste heat in the form of hot water at 120 ◦C for district heating potentially unlocking further cost reductions to 1.24 €/kg. In conclusion gasification of locally available solid fuels should be seriously considered next to natural gas and electrolysis for supplying the emerging hydrogen economy.
Green Hydrogen Production: Integrating Environmental and Social Criteria to Ensure Sustainability
Jul 2023
Publication
Hydrogen is experiencing an unprecedented global hype. Hydrogen is globally discussed as a possible future energy carrier and regarded as the urgently needed building block for the much needed carbon-neutral energy transition of hard-to-abate sectors to mitigate the effects of global warming. This article provides synthesised measurable sustainability criteria for analysing green hydrogen production proposals and strategies. Drawn from expert interviews and an extensive literature review this article proposes that a sustainable hydrogen production should consider six impact categories; Energy transition Environment Basic needs Socio-economy Electricity supply and Project planning. The categories are broken down into sixteen measurable sustainability criteria which are determined with related indicators. The article concludes that low economic costs can never be the only decisive criterion for the hydrogen production; social aspects must be integrated along the entire value chain. The compliance with the criteria may avoid social and ecological injustices in the planning of green hydrogen projects and increases inter alia the social welfare of the affected population.
Environmental and Material Criticality Assessment of Hydrogen Production via Anion Exchange Membrane Electrolysis
Oct 2023
Publication
The need to drastically reduce greenhouse gas emissions is driving the development of existing and new technologies to produce and use hydrogen. Anion exchange membrane electrolysis is one of these rapidly developing technologies and presents promising characteristics for efficient hydrogen production. However the environmental performance and the material criticality of anion exchange membrane electrolysis must be assessed. In this work prospective life cycle assessment and criticality assessment are applied first to identify environmental and material criticality hotspots within the production of anion exchange membrane electrolysis units and second to benchmark hydrogen production against proton exchange membrane electrolysis. From an environmental point of view the catalyst spraying process heavily dominates the ozone depletion impact category while the production of the membrane represents a hotspot in terms of the photochemical ozone formation potential. For the other categories the environmental impacts are distributed across different components. The comparison of hydrogen production via anion exchange membrane electrolysis and proton exchange membrane electrolysis shows that both technologies involve a similar life-cycle environmental profile due to similar efficiencies and the leading role of electricity generation for the operation of electrolysis. Despite the fact that for proton exchange membrane electrolysis much less material is required due to a higher lifetime anion exchange membrane electrolysis shows significantly lower raw material criticality since it does not rely on platinum-group metals. Overall a promising environmental and material criticality performance of anion exchange membrane electrolysis for hydrogen production is concluded subject to the expected technical progress for this technology.
Green Hydrogen and Electrical Power Production through the Integration of CO2 Capturing from Biogas: Process Optimization and Dynamic Control
Jun 2021
Publication
This study describes the optimization of a modelling process concerning biogas’ use to generate green hydrogen and electrical power. The Aspen Plus simulation tool is used to model the procedure and the approach employed to limit the emissions of gas from the hydrogen production process will be the CO2 capture method. This technique uses slack lime (Ca(OH)2) to absorb CO2 capture since it is readily available. The study analyzes many critical parameters in the process including the temperature and pressure in the steam reforming (SR) and the water gas shift (WGS) reactions along with the steam to carbon ratio (S/C) to determine how the production of green hydrogen and electrical power will be influenced. Electricity generation is achieved by taking the residual water from the SR WGS carbonation reactions and converting it to the vapour phase allowing the steam to pass through the turbine to generate electricity. To examine the effects of the synchronized critical parameters response surface methodology (RSM) was used thus allowing the optimal operational conditions to be determined in the form of an optimized zone for operation. The result of parameter optimization gave the maximum green hydrogen production of 211.46 kmol/hr and electric power production of 2311.68 kWh representing increases of 34.86% and 5.62% respectively when using 100 kmol/hr of biogas. In addition control structures were also built to control the reactors’ temperature in the dynamic section. The tuning parameters can control the SR and WGS system’s reactor to maintain the system in approximately 0.29 h and 0.32 h respectively.
Reversible Molten Catalytic Methane Cracking Applied to Commercial Solar-Thermal Receivers
Nov 2020
Publication
When driven by sunlight molten catalytic methane cracking can produce clean hydrogen fuel from natural gas without greenhouse emissions. To design solar methane crackers a canonical plug flow reactor model was developed that spanned industrially relevant temperatures and pressures (1150–1350 Kelvin and 2–200 atmospheres). This model was then validated against published methane cracking data and used to screen power tower and beam-down reactor designs based on “Solar Two” a renewables technology demonstrator from the 1990s. Overall catalytic molten methane cracking is likely feasible in commercial beam-down solar reactors but not power towers. The best beam-down reactor design was 9% efficient in the capture of sunlight as fungible hydrogen fuel which approaches photovoltaic efficiencies. Conversely the best discovered tower methane cracker was only 1.7% efficient. Thus a beam-down reactor is likely tractable for solar methane cracking whereas power tower configurations appear infeasible. However the best simulated commercial reactors were heat transfer limited not reaction limited. Efficiencies could be higher if heat bottlenecks are removed from solar methane cracker designs. This work sets benchmark conditions and performance for future solar reactor improvement via design innovation and multiphysics simulation.
No more items...