Safety

Hydrogen is a key parameter to monitor radioactive disposal facility such as the envisioned French geological repository for nuclear wastes. The use of microcantilevers as chemical sensors usually involves a sensitive layer whose purpose is to selectively sorb the analyte of interest. The sorbed substance can then be detected by monitoring either the resonant frequency shift (dynamic mode) or the quasi-static deflection (static mode). The objective of this paper is to demonstrate the feasibility of eliminating the need for the sensitive layer in the dynamic mode thereby increasing the long-term reliability. The microcantilever resonant frequency allows probing the mechanical properties (mass density and viscosity) of the surrounding fluid and thus to determine the concentration of a species in a binary gaseous. Promising preliminary work has allowed detecting concentration of 200 ppm of hydrogen in air with non-optimized geometry of silicon microcantilever with integrated actuation and read-out.

Polymers for O-rings valve seats gaskets and other sealing applications in the hydrogen infrastructure face extreme conditions of high-pressure H2 (0.1 to 100 MPa) during normal operation. To fill current knowledge gaps and to establish standard test methods for polymers in H2 environments these materials can be tested in laboratory scale H2 manifolds mimicking end use pressure and temperature conditions. Beyond the influence of high pressure H2 the selection of gases used for leak detection in the H2 test manifold their pressures and times of exposure gas types relative diffusion and permeation rates are all important influences on the polymers being tested. These effects can be studied ex-situ with post-exposure characterization. In a previous study four polymers (Viton A Buna N High Density Polyethylene (HDPE) and Polytetrafluoroethylene (PTFE)) commonly used in the H2 infrastructure were exposed to high-pressure H2 (100 MPa). The observed effects of H2 were consistent with typical polymer property-structure relationships; in particular H2 affected elastomers more than thermoplastics. However since high pressure He was used for purging and leak detection prior to filling with H2 a study of the influence of the purge gas on these polymers was considered necessary to isolate the effects of H2 from those of the purge gas. Therefore in this study Viton A Buna N and PTFE were exposed to the He purge procedure without the subsequent H2 exposure. Additionally six polymers Viton A Buna N PTFE Polyoxymethylene (POM) Polyamide 11 (Nylon) and Ethylenepropylenediene monomer rubber (EPDM) were subjected to high pressure Ar (100 MPa) followed by high pressure H2 (100 MPa) under the same static isothermal conditions to identify the effect of a purge gas with a significantly larger molecular size than He. Viton A and Buna N elastomers are more prone to irreversible changes as a result of H2 exposure from both Ar and He leak tests as indicated by influences on storage modulus extent of swelling and increased compression set. EPDM even though it is an elastomer is not as prone to high-pressure gas influences. The thermoplastics are generally less influenced by high pressure regardless of the gas type. Conclusions from these experiments will provide insight into the influence of purging processes and purge gases on the subsequent testing in high pressure gaseous H2. Control for the influence of purging on testing results is essential for the development of robust test methods for evaluating the effects of H2 and other high-pressure gases on the properties of polymers.

An accident modelling approach is used to assess the safety of a hydrogen station as part of a ground transportation network. The method incorporates prevention barriers associated to human factors management and organizational failures in a risk assessment framework. Failure probabilities of these barriers and end-states events are predicted using Fault Tree Analysis and Event Tree Analysis respectively. Results from the case study considered revealed the capability of the proposed method in estimating the likelihood of various outcomes as well as predicting the future probability. In addition the scheme offers opportunity to provide dynamic adjustment by updating the failure probability with actual plant data. Results from the analysis can be used to plan maintenance and management of change as required by the plant condition.

We at Kawasaki Heavy Industries have proposed a "CO2-Free H2 supply chain" using abundant brown coal of Australian origin as the energy source. This chain will store CO2 generated during the process for producing hydrogen from brown coal in a project (Carbon Net) that the Australia Government is promoting. Thus Japan can import CO2-free hydrogen. The supply chain consists of the hydrogen production system the hydrogen transport/storage system and the hydrogen use system. Related to their designs we have to consider their hazards polluted scenarios and safety measures via a safety assessment process that is compliant with international risk assessment standards. To verify safety designs related experiments and analyses will be conducted. This paper describes the approach to safety design for especially the related liquid hydrogen facilities.

In the present study the phenomena of blast wave and fireball generated by high pressure (35 MPa) hydrogen tank (72 l) rupture have been investigated numerically. The realizable k-ε turbulence model was applied. The simulation of the combustion process is based on the eddy dissipation model coupled with the one step chemical reaction mechanism. Simulation results are compared with experimental data from a stand-alone hydrogen fuel tank rapture following a bonfire test. The model allows the study of the interaction between combustion process and blast wave propagation. Simulation results (blast wave overpressure fireball shape and size) follow the trends observed in the experiment.

This study deals with the TNO Multi-Energy and Baker-Strehlow-Tang (BST) methods for estimating the positive overpressures and positive impulses resulting from hydrogen-air explosions. With these two methods positive overpressure and positive impulse results depend greatly on the choice of the class number for the TNO Multi-Energy method or the Mach number for the BST methods. These two factors permit the user to read the reduced parameters of the blast wave from the appropriate monographs for each of these methods i.e. positive overpressure and positive duration phase for the TNO Multi-Energy method and positive overpressure and positive impulse for the BST methods. However for the TNO Multi-Energy method the determination of the class number is not objective because it is the user who makes the final decision in choosing the class number whereas with the BST methods the user is strongly guided in their choice of an appropriate Mach number. These differences in the choice of these factors can lead to very different results in terms of positive overpressure and positive impulse. Therefore the objective of this work was to compare the positive overpressures and positive impulses predicted with the TNO Multi-Energy and BST methods with data available from large-scale experiments.

This work presents a parametric study on the similitude between hydrogen and helium distribution when released in the air by a source located inside of a naturally ventilated enclosure with two vents. Several configurations were experimentally addressed in order to improve knowledge on dispersion. Parameters were chosen to mimic operating conditions of hydrogen energy systems. Thus the varying parameters of the study were mainly the source diameter the releasing flow rate the volume and the geometry of the enclosure. Two different experimental set-ups were used in order to vary the enclosure's height between 1 and 2 m. Experimental results obtained with helium and hydrogen were compared at equivalent flow rates determined with existing similitude laws. It appears for the plume release case that helium can suitably be used for predicting hydrogen dispersion in these operating designs. On the other hand – when the flow turns into a jet – non negligible differences between hydrogen and helium dispersion appear. In this case helium – used as a direct substitute to hydrogen – will over predict concentrations we would get with hydrogen. Therefore helium concentration read-outs should be converted to obtain correct predictions for hydrogen. However such a converting law is not available yet.

Hydrogen is being considered as a pathway to decarbonize large energy systems and for utility-scale energy storage. As these applications grow transportation infrastructure that can accommodate large quantities of hydrogen will be needed. Many millions of tons of hydrogen are already consumed annually some of which is transported in dedicated hydrogen pipelines. The materials and operation of these hydrogen pipeline systems however are managed with more constraints than a conventional natural gas pipeline. Transitional strategies for deep decarbonization of energy systems include blending hydrogen into existing natural gas systems where the materials and operations may not have the same controls. This study explores the hydrogen compatibility of existing pipeline steels and the suitability of these steels in hydrogen pipeline systems. Representative fracture and fatigue properties of pipeline grade steels in gaseous hydrogen are summarized from the literature. These properties are then considered in idealized design life calculations to inform materials performance for a typical gas pipeline.

The addition of hydrogen to natural gas for heating and cooking is being considered as a route to reducing carbon emissions in the United Kingdom (UK). The HyDeploy programme (hereafter referred to as HyDeploy) aims to demonstrate that hydrogen can be added to the natural gas supply without compromising public safety or appliance performance. This paper relates to the preparatory work for hydrogen injection on a live site at Keele University closed network comprising domestic premises multi-occupancy buildings and light commercial premises. The project is based around the injection of up to 20 %mol/mol hydrogen into mains natural gas at pressures below 2 barg. Work streams addressed during the pre-trial preparation included; assessment of material interaction with hydrogen blends for all distribution system components and appliances; understanding of gas appliance behaviour; review of: gas detection systems fire and explosion considerations routine and emergency procedural considerations; and the design of a new hydrogen injection grid entry unit. This paper describes the safety and regulatory challenges that were encountered during preparation of the project including obtaining the necessary regulatory permissions to blend hydrogen gas.

Experimental data from vented explosion tests using lean hydrogen–air mixtures with concentrations from 12 to 19% vol. are presented. A 63.7-m3 chamber was used for the tests with a vent size of either 2.7 or 5.4 m2. The tests were focused on the effect of hydrogen concentration ignition location vent size and obstacles on the pressure development of a propagating flame in a vented enclosure. The dependence of the maximum pressure generated on the experimental parameters was analyzed. It was confirmed that the pressure maxima are caused by pressure transients controlled by the interplay of the maximum flame area the burning velocity and the overpressure generated outside of the chamber by an external explosion. A model proposed earlier to estimate the maximum pressure for each of the main pressure transients was evaluated for the various hydrogen concentrations. The effect of the Lewis number on the vented explosion overpressure is discussed.