Canada
Quantitative Imaging of Multi-Component Turbulent Jets
Sep 2011
Publication
The integration of a hydrogen gas storage arrangement in vehicles has not been without its challenges. Gaseous state of hydrogen at ambient temperature combined with the fact that hydrogen is highly flammable results in the requirement of more robust high pressure storage systems that can meet modern safety standards. To develop these new safety standards and to properly predict the phenomena of hydrogen dispersion a better understanding of the resulting flow structures and flammable region from controlled and uncontrolled releases of hydrogen gas must be achieved. With the upper and lower explosive limits of hydrogen known the flammable envelope surrounding the site of a uncontrolled hydrogen release can be found from the concentration field. In this study the subsonic release of hydrogen was emulated using helium as a substitute working fluid. A sharp orifice round turbulent jet is used to emulate releases in which leak geometry is circular. Effects of buoyancy and crossflow were studied over a wide range of Froude numbers. The velocity fields of turbulent jets were characterized using particle image velocimetry (PIV). The mean and fluctuation velocity components were well quantified to show the effect of buoyancy due to the density difference between helium and the surrounding air. In the range of Froude numbers investigated (Fr = 1000 750 500 250 and 50) the increasing effects of buoyancy were seen to be proportional to the reduction of the Fr number. While buoyancy is experienced to have a negligible effect on centerline velocity fluctuations acceleration due to buoyancy in the other hand resulted in a slower decay of time-averaged axial velocity component along the centerline. The obtained results will serve as control reference values for further concentration measurement study and for computational fluid dynamics (CFD) validation.
Estimation of Filling Time for Compressed Hydrogen Refueling
Mar 2019
Publication
In order to facilitate the application of hydrogen energy and ensure its safety the compressed hydrogen storage tank on board needs to be full of hydrogen gas within 3 minutes. Therefore to meet this requirement the effects of refueling parameters on the filling time need to be investigated urgently. For the purpose of solving this issue a novel analytical solution of filling time is obtained from a lumped parameter model in this paper. According to the equation of state for real gas and dimensionless numbers Nu and Re the function relationships between the filling time and the refueling parameters are presented. These parameters include initial temperature initial pressure inflow temperature final temperature and final pressure. These equations are used to fit the reference data the results of fitting show good agreement. Then the values of fitting parameters are further utilized so as to verify the validity of these formulas. We believe this study can contribute to control the hydrogen filling time and ensure the safety during fast filling process.
Validation Testing In Support Of Hydrogen Codes and Standards Developments
Sep 2011
Publication
New codes and standards are being developed to facilitate the safe deployment of emerging hydrogen technologies. Hydrogen markets will benefit from standards that address the specific properties of hydrogen hydrogen effects on strength of materials and hydrogen compressed gas storage at pressures up to 70 MPa. The need for validation of new hydrogen requirements has been identified by codes and standards technical committees. The US Department of Energy (DOE) office of Energy Efficiency and Renewable Energy (EERE) has tasked the National Renewable Energy Laboratory (NREL) with the role of supporting hydrogen codes and standards research and development needs. NREL has provided validation test support to several new standards development efforts including pressure testing of 70 MPa on board vehicle storage systems flaw testing of stationary hydrogen tanks fill protocols for hydrogen fuel dispensing and hydrogen compatibility testing for hydrogen pressure relief devices (HPRD’s). Validation test results are presented for these four specific standards development needs.
Effects of Chemical Kinetics on Ignition of Hydrogen Jets
Sep 2013
Publication
During the early phase of the transient process following a hydrogen leak into the atmosphere a contact surface appears separating air heated by the leading shock from hydrogen cooled by expansion. Locally the interface is approximately planar. Diffusion leads to a temperature decrease on the air side and an increase in the hydrogen-filled region and mass diffusion of hydrogen into air and of air into hydrogen potentially resulting in ignition. This process was analyzed by Li ˜nan and Crespo [1] for unity Lewis number and Li ˜nan and Williams [2] for Lewis number less than unity. We included in the analysis the effect of a slow expansion [3 4] leading to a slow drop in temperature which occurs in transient jets. Chemistry being very temperature-sensitive the reaction rate peaks close to the hot side of the interface where only a small fuel concentration present close to the warm air-rich side which depends crucially upon the fuel Lewis number. For Lewis number unity the fuel concentration due to diffusion is comparable to the rate of consumption by chemistry. If the Lewis number is less than unity diffusion brings in more fuel than temperature-controlled chemistry consumes. For a Lewis number greater than unity diffusion is not strong enough to bring in as much fuel as chemistry would burn; combustion is controlled by fuel diffusion. If the temperature drop due to expansion associated with the multidimensional jet does not lower significantly the reaction rate up to that point analysis shows that ignition in the jet takes place. For fuel Lewis number greater than unity chemistry does not lead to a defined explosion so that eventually expansion will affect the process; ignition does not take place [3 4]. In the current paper these results are extended to consider multistep chemical kinetics but for otherwise similar assumptions. High activation energy is no longer applicable. Instead results are obtained in the short time limit still as a perturbation superimposed to the self-similar solution to the chemically frozen diffusion solution. In that approximation the initiation step which consumes fuel and oxidant is taken to be slow compared with steps that consume one of the reactants and an intermediate species. The formulation leads to a two point boundary value problem for set of coupled rate equations plus an energy equation for perturbations. These equations are linear with variable co-effcients. The coupled problem is solved numerically using a split algorithm in which chemical reaction is solved for frozen diffusion while diffusion is solved for frozen chemistry. At each time step the still coupled linear problem is solved exactly by projecting onto the eigenmodes of the stiff matrix so that the solution is unaffected by stiffness. Since in the short time limit temperature is only affected at the perturbation level the matrix depends only on the similarity variable x t but it is otherwise time-independent. As a result determination of the eigenvalues and eigenvectors is only done once (using Maple) for the entire range of discretized values of the similarity variable. The diffusion problem consists of a set of independent equations for each species. Each of these is solved using orthogonal decomposition onto Hermite polynomials for the homogeneous part plus a particular solution proportional to time for the non-homogeneous (source) terms. That approach can be implemented for different kinetic schemes.
Simulations of Hydrogen Releases from a Storage Tanks- Dispersion and Consequences of Ignition
Sep 2005
Publication
We present results from hydrogen dispersion simulations from a pressurized reservoir at constant flow rate in the presence and absence of a wall. The dispersion simulations are performed using a commercial finite volume solver. Validation of the approach is discussed. Constant concentration envelopes corresponding to the 2% 4% and 15% hydrogen concentration in air are calculated for a subcritical vertical jet and for an equivalent subcritical horizontal jet from a high pressure reservoir. The consequences of ignition and the resulting overpressure are calculated for subcritical horizontal and vertical hydrogen jets and in the latter case compared to available experimental data.
PRD Hydrogen Release and Dispersion, a Comparison of CFD Results Obtained from Using Ideal and Real Gas Law Properties.
Sep 2005
Publication
In this paper CFD techniques were applied to the simulations of hydrogen release from a 400-bar tank to ambient through a Pressure Relieve Device (PRD) 6 mm (¼”) opening. The numerical simulations using the TOPAZ software developed by Sandia National Laboratory addressed the changes of pressure density and flow rate variations at the leak orifice during release while the PHOENICS software package predicted extents of various hydrogen concentration envelopes as well as the velocities of gas mixture for the dispersion in the domain. The Abel-Noble equation of state (AN-EOS) was incorporated into the CFD model implemented through the TOPAZ and PHOENICS software to accurately predict the real gas properties for hydrogen release and dispersion under high pressures. The numerical results were compared with those obtained from using the ideal gas law and it was found that the ideal gas law overestimates the hydrogen mass release rates by up to 35% during the first 25 seconds of release. Based on the findings the authors recommend that a real gas equation of state be used for CFD predictions of high-pressure PRD releases.
Feasibility Investigation of Hydrogen Refuelling Infrastructure for Heavy‐Duty Vehicles in Canada
Apr 2022
Publication
A potentially viable solution to the problem of greenhouse gas emissions by vehicles in the transportation sector is the deployment of hydrogen as alternative fuel. A limitation to the diffusion of the hydrogen‐fuelled vehicles option is the intricate refuelling stations that vehicles will require. This study examines the practical use of hydrogen fuel within the internal combustion engine (ICE)‐powered long‐haul heavy‐duty trucking vehicles. Specifically it appraises the techno‐ economic feasibility of constructing a network of long‐haul truck refuelling stations using hydrogen fuel across Canada. Hydrogen fuel is chosen as an option for this study due to its low carbon emissions rate compared to diesel. This study also explores various operational methods including variable technology integration levels and truck traffic flows truck and pipeline delivery of hydrogen to stations and the possibility of producing hydrogen onsite. The proposed models created for this work suggest important parameters for economic development such as capital costs for station construction the selling price of fuel and the total investment cost for the infrastructure of a nation‐ wide refuelling station. Results showed that the selling price of hydrogen gas pipeline delivery op‐ tion is more economically stable. Specifically it was found that at 100% technology integration the range in selling prices was between 8.3 and 25.1 CAD$/kg. Alternatively at 10% technology integration the range was from 12.7 to 34.1 CAD$/kg. Moreover liquid hydrogen which is delivered by trucks generally had the highest selling price due to its very prohibitive storage costs. However truck‐delivered hydrogen stations provided the lowest total investment cost; the highest is shown by pipe‐delivered hydrogen and onsite hydrogen production processes using high technology integration methods. It is worth mentioning that once hydrogen technology is more developed and deployed the refuelling infrastructure cost is likely to decrease considerably. It is expected that the techno‐economic model developed in this work will be useful to design and optimize new and more efficient hydrogen refuelling stations for any ICE vehicles or fuel cell vehicles.
Challenges and Important Considerations When Benchmarking Single-cell Alkaline Electrolyzers
Nov 2021
Publication
This study outlines an approach to identifying the difficulties associated with the bench-marking of alkaline single cells under real electrolyzer conditions. A challenging task in the testing and comparison of different catalysts is obtaining reliable and meaningful benchmarks for these conditions. Negative effects on reproducibility were observed due to the reduction in conditioning time. On the anode side a stable passivation layer of NiO can be formed by annealing of the Ni foams which is even stable during long-term operation. Electrical contact resistance and impedance measurements showed that most of the contact resistance derived from the annealed Ni foam. Additionally analysis of various overvoltages indicated that most of the total overvoltage comes from the anode and cathode activation overpotential. Different morphologies of the substrate material exhibited an influence on the performance of the alkaline single cell based on an increase in the ohmic resistance.
Vertical Turbulent Buoyant Helium Jet - CFD Modelling and Validation
Sep 2005
Publication
In this paper a vertical turbulent round jet of helium was studied numerically using the PHOENICS software package. The flow was assumed to be steady incompressible and turbulent. The jet discharge Froude number was 14000 and the turbulent Schmidt number was 0.7. The incompressible Reynolds average Navier-Stokes equations and helium transport equation expressed in 2-D axisymmetric domain were applied to model the underlying helium release. The k-e RNG turbulence model was used for the calculations of the corresponding turbulent viscosity diffusivity velocity and concentration fields in the domain. The simulation results are compared with the experimental measurements from the earlier published studies on helium jets in non-buoyant jet region (NBJ) intermediate region (I) and buoyant plume region (BP). The numerical results show that the radial profiles of mean velocity and mean concentration are consistent with the empirical data scaled by the effective diameter and density-ratio dependence. The mean velocity and concentration fields along the axis of the jet agree with the decay laws correlated from the previous experiments. The discrepancy between the numerical and experimental data is within 10% proving that the current CFD model for gas release and dispersion is robust accurate and reliable and that the CFD technique can be used as an alternative to the experiments with similar helium jets. The authors believe that the current CFD model is well validated through this study and can be further extended to predict similar hydrogen releases and dispersion if the model is properly applied with hydrogen properties.
The Role of Charging and Refuelling Infrastructure in Supporting Zero-emission Vehicle Sales
Mar 2020
Publication
Widespread uptake of battery electric plug-in hybrid and hydrogen fuel-cell vehicles (collectively zero-emissions vehicles or ZEVs) could help many regions achieve deep greenhouse gas mitigation goals. Using the case of Canada this study investigates the extent to which increasing ZEV charging and refuelling availability may boost ZEV sales relative to other ZEV-supportive policies. We adapt a version of the Respondent-based Preferences and Constraints (REPAC) model using 2017 survey data from 1884 Canadian new vehicle-buyers to simulate the sales impacts of increasing electric vehicle charging access at home work public destinations and on highways as well as increasing hydrogen refuelling station access. REPAC is built from a stated preference choice model and represents constraints in supply and consumer awareness as well as dynamics in ZEV policy out to 2030. Results suggest that new ZEV market share from 2020 to 2030 does not substantially benefit from increased infrastructure. Even when electric charging and hydrogen refuelling access are simulated to reach “universally” available levels by 2030 ZEV sales do not rise by more than 1.5 percentage points above the baseline trajectory. On the other hand REPAC simulates ZEV market share rising as high as 30% by 2030 with strong ZEV-supportive policies even without the addition of charging or refuelling infrastructure. These findings stem from low consumer valuation of infrastructure found in the stated preference model. Results suggest that achieving ambitious ZEV sale targets requires a comprehensive suite of policies beyond a focus on charging and refuelling infrastructure.
Experimental Results and Comparison with Simulated Data of a Low Pressure Hydrogen Jet
Sep 2011
Publication
Experiments with a hydrogen jet were performed at two different pressures 96 psig (6.6 bars) and 237 psig (16.3 bars). The hydrogen leak was generated at two different hole sizes 1/16 inch (1.6 mm) and 1/32 inch (0.79 mm). The flammable shape of the plume was characterised by numerous measurements of the hydrogen concentration inside of the jet. The effect of the nearby horizontal surface on the shape of the plume was measured and compared with results of CFD numerical simulations. The paper will present results and an interpretation on the nature of the plume shape.
Defining Hazardous Zones – Electrical Classification Distances
Sep 2005
Publication
This paper presents an analysis of computational fluid dynamic models of compressed hydrogen gas leaks into the air under different conditions to determine the volume of the hydrogen/air mixture and the extents of the lower flammable limit. The necessary hole size was calculated to determine a reasonably expected hydrogen leak rate from a valve or a fitting of 5 and 20 cfm under 400 bars resulting in a 0.1 and 0.2 mm effective diameter hole respectively. The results were compared to calculated hypothetical volumes from IEC 60079-10 for the same mass flowrate and in most cases the CFD results produced significantly smaller hydrogen/air volumes than the IEC standard. Prescriptive electrical classification distances in existing standards for hydrogen and compressed natural gas were examined but they do not consider storage pressure and there appears to be no scientific basis for the distance determination. A proposed table of electrical classification distances incorporating hydrogen storage volume and pressure was produced based on the hydrogen LFL extents from a 0.2 mm diameter hole and the requirements of existing standards. The PHOENICS CFD software package was used to solve the continuity momentum and concentration equations with the appropriate boundary conditions buoyancy model and turbulence models. Numerical results on hydrogen concentration predictions were obtained in the real industrial environment typical for a hydrogen refuelling or energy station.<br/><br/>
Fire Protection Strategy for Compressed Hydrogen-Powered Vehicles
Sep 2007
Publication
Virtually all major automotive companies are currently developing hydrogen-powered vehicles. The vast majority of them employ compressed hydrogen tanks and components as a means of storing the fuel onboard. Compressed hydrogen vehicle fuel systems are designed in the same way as compressed natural gas vehicles (NGV) i.e. the high pressure (up to 70 MPa) fuel is always contained within the system under all conditions with the exception of vehicular fire. In the event of a vehicle fire the fuel system is protected using a non-reclosing thermally activated pressure relief device (PRD) which safely vents the contents. Hydrogen fuel system PRDs are presently qualified to the performance requirements specified in draft hydrogen standards such ANSI/CSA HPRD 1 and EIHP Rev. 12b. They are also qualified with individual fuel tank designs in accordance with the engulfing bonfire requirements in various published/draft tank standards such as CSA B51 Part 2 JARI S001 SAE TIR J2579 ANSI/CSA HGV 2 ISO DIS 15869.2 and EIHP Rev. 12b. Since 2000 there have been over 20 documented NGV tank failures in service 11 of which have been attributed to vehicle fires. This paper will examine whether currently proposed hydrogen performance standards and installation requirements offer suitable fuel system protection in the event of vehicular fires. A number of alternative fire protection strategies will be discussed including:
- The requirement of an engulfing and/or localized fire test for individual tanks fuel systems and complete vehicles;
- The advantages/disadvantages of point source- surface area- and/or fuse-based PRDs
- The use of thermal insulating coatings/blankets for fire protection resulting in the NONventing of the fuel
- The specification of appropriate fuel system installation requirements to mitigate the effect of vehicular fires.
Hydrogen Deflagrations in Stratified Flat Layers in the Large-scale Vented Combustion Test Facility
Sep 2019
Publication
This paper examines the flame dynamics of vented deflagration in stratified hydrogen layers. It also compares the measured combustion pressure transients with 3D GOTHIC simulations to assess GOTHIC’s capability in simulating the associated phenomena. The experiments were performed in the Large-Scale Vented Combustion Test Facility at the Canadian Nuclear Laboratories. The stratified layer was formed by injecting hydrogen at a high elevation at a constant flow rate. The dominant parameters for vented deflagrations in stratified layers were investigated. The experimental results show that significant overpressures are generated in stratified hydrogen–air mixtures with local high concentration although the volume-averaged hydrogen concentration is non-flammable. The GOTHIC predictions capture the overall pressure dynamics of combustion very well but the peak overpressures are consistently over-predicted particularly with higher maximum hydrogen concentrations. The measured combustion overpressures are also compared with Molkov’s model prediction based on a layer-averaged hydrogen concentration.
Numerical and Experimental Investigation of Buoyant Gas Release
Sep 2009
Publication
Buoyant round vertical jet had been investigated using Large Eddy Simulations at low Mach number. For the purpose of comparison with in-house experimental data in the present work helium has been used as a substitute for hydrogen. The influence of the transient concentration fields on the volume of gas with concentration within flammability limits has been investigated and their evolution and relation with average fields ad been characterized. Transient concentration fields created during initial jet development had been considered. Numerical results have been compared with in-house experiments and data published in the literature.
Numerical Investigation of a Vertical Surface on the Flammable Extent of Hydrogen and Methane Vertical Jets
Sep 2011
Publication
The effect of vertical surface on the extent of high pressure unignited jets of both hydrogen and methane is studied using computer fluid dynamics simulations performed with FLACS Hydrogen. Results for constant flow rate through a 6.35 mm round leak orifice from 100 barg 250 barg 400 barg 550 barg and 700 barg compressed gas systems are presented for vertical jets. To quantify the effect of the surface on the jet the jet exit is positioned at various distances from the surface ranging from 0.029 m to 12 m. Free jets simulations are performed for comparison purposes.
Experimental Study of the Spontaneous Ignition of Partly Confined Hydrogen Jets
Sep 2011
Publication
The current study addresses the spontaneous ignition of hydrogen jets released into a confined oxidizer environment experimentally. The experiments are conducted in a shock tube where hydrogen gas is shock-accelerated into oxygen across a perforated plate. The operating conditions and hole dimension of the plate were varied in order to identify different flow field and ignition scenarios. Time resolved Schlieren visualization permitted to reconstruct the gasdynamic evolution of the release and different shock interactions. Time resolved self-luminosity records permitted us to record whether ignition was achieved and also to record the dimension of the turbulent mixing layer. The ignition limits determined experimentally in good agreement with the 1D diffusion ignition model proposed by Maxwell and Radulescu. Nevertheless the experiments demonstrated that the mixing layer is two to three orders of magnitude thicker than predicted by molecular diffusion which can be attributed to the observed mixing layer instabilities and shock-mixing layer interactions which provide a much more intense mixing rate than anticipated from previous and current numerical predictions. These observations further clarify why releases through partly confined geometries are more conducive to jet ignition of the jets.
Risk-Informed Process and Tools for Permitting Hydrogen Fueling Stations
Sep 2007
Publication
The permitting process for hydrogen fueling stations varies from country to country. However a common step in the permitting process is the demonstration that the proposed fueling station meets certain safety requirements. Currently many permitting authorities rely on compliance with well known codes and standards as a means to permit a facility. Current codes and standards for hydrogen facilities require certain safety features specify equipment made of material suitable for hydrogen environment and include separation or safety distances. Thus compliance with the code and standard requirements is widely accepted as evidence of a safe design. However to ensure that a hydrogen facility is indeed safe the code and standard requirements should be identified using a risk-informed process that utilizes an acceptable level of risk. When compliance with one or more code or standard requirements is not possible an evaluation of the risk associated with the exemptions to the requirements should be understood and conveyed to the Authority Having Jurisdiction (AHJ). Establishment of a consistent risk assessment toolset and associated data is essential to performing these risk evaluations. This paper describes an approach for risk-informing the permitting process for hydrogen fueling stations that relies primarily on the establishment of risk-informed codes and standards. The proposed risk-informed process begins with the establishment of acceptable risk criteria associated with the operation of hydrogen fueling stations. Using accepted Quantitative Risk Assessment (QRA) techniques and the established risk criteria the minimum code and standard requirements necessary to ensure the safe operation of hydrogen facilities can be identified. Risk informed permitting processes exist in some countries and are being developed in others. To facilitate consistent risk-informed approaches the participants in the International Energy Agency (IEA) Task 19 on hydrogen safety are working to identify acceptable risk criteria QRA models and supporting data.
Fundamental Safety Testing and Analysis of Solid State Hydrogen Storage Materials and Systems
Sep 2007
Publication
Hydrogen is seen as the future automobile energy storage media due to its inherent cleanliness upon oxidation and its ready utilization in fuel cell applications. Its physical storage in light weight low volume systems is a key technical requirement. In searching for ever higher gravimetric and volumetric density hydrogen storage materials and systems it is inevitable that higher energy density materials will be studied and used. To make safe and commercially acceptable systems it is important to understand quantitatively the risks involved in using and handling these materials and to develop appropriate risk mitigation strategies to handle unforeseen accidental events. To evaluate these materials and systems an IPHE sanctioned program was initiated in 2006 partnering laboratories from Europe North America and Japan. The objective of this international program is to understanding the physical risks involved in synthesis handling and utilization of solid state hydrogen storage materials and to develop methods to mitigate these risks. This understanding will support ultimate acceptance of commercially high density hydrogen storage system designs. An overview of the approaches to be taken to achieve this objective will be given. Initial experimental results will be presented on environmental exposure of NaAlH4 a candidate high density hydrogen storage compound. The tests to be shown are based on United Nations recommendations for the transport of hazardous materials and include air and water exposure of the hydride at three hydrogen charge levels in various physical configurations. Additional tests developed by the American Society for Testing and Materials were used to quantify the dust cloud ignition characteristics of this material which may result from accidental high energy impacts and system breach. Results of these tests are shown along with necessary risk mitigation techniques used in the synthesis and fabrication of a prototype hydrogen storage system.
Simulation of Detonation after an Accidental Hydrogen Release in Enclosed Environments
Sep 2007
Publication
An accidental hydrogen release in equipment enclosures may result in the presence of a detonable mixture in a confined environment. Numerical simulation is potentially a useful tool for damage assessment in these situations. To assess the value of CFD techniques numerical simulation of detonation was performed for two realistic scenarios. The first scenario starts with a pipe failure in an electrolyzer resulting in a leak of 42 g of hydrogen. The second scenario deals with a failure in a reformer where 84 g of hydrogen is released. In both cases dispersion patterns were first obtained from separate numerical simulation and were then used as initial condition in a detonation simulation based upon the reactive Euler's equations. Energy was artificially added in a narrow region to simulate detonative ignition. In the electrolyzer ignition was assumed to occur 500 ms after beginning of the release. Results show a detonation failing on the top and bottom side but propagating left and right before eventually failing also. Average impulse was 500 Ns/m². For the reformer three cases were simulated with ignition 1.0 1.4 and 2.0 seconds after the beginning of the release. In two cases the detonation wave failed everywhere except in the direction of the release in which it continued propagating until reaching the side wall. In the third the detonation failed everywhere at first but later a deflagration to detonation transition occurred resulting in a strong wave that propagated rapidly toward the side wall. In all three cases the consequences are more serious than in the electrolyzer.
High Pressure Hydrogen Jets in the Presence of a Surface
Sep 2009
Publication
The effect of surfaces on the extent of high pressure vertical and horizontal unignited jets is studied using CFD numerical simulations performed with FLACS Hydrogen and Phoenics. For a constant flow rate release of hydrogen from a 284 bar storage unit through a 8.5 mm orifice located 1 meter from the ground the maximum extent of the flammable cloud is determined as a function of time and compared to a free vertical hydrogen jet under identical release conditions. The results are compared to methane numerical simulations and to the predictions of the Birch correlations for the size of the flammable cloud. We find that the maximum extent of the flammable clouds of free jets obtained using CFD numerical simulations for both hydrogen and methane are in agreement with the Birch predictions. For hydrogen horizontal free jets there is strong buoyancy effect observed towards the end of the flammable cloud thus noticeably reducing its centreline extent. For methane horizontal free jets this effect is not observed. For methane the presence of the ground results in a pronounced increase in the extent of the flammable cloud compared to a free jet. The effects of a surface on vertical jets are also studied.
Study on Temper Embrittlement and Hydrogen Embrittlement of a Hydrogenation Reactor by Small Punch Test
Jun 2017
Publication
The study on temper embrittlement and hydrogen embrittlement of a test block from a 3Cr1Mo1/4V hydrogenation reactor after ten years of service was carried out by small punch test (SPT) at different temperatures. The SPT fracture energy Esp (derived from integrating the load-displacement curve) divided by the maximum load (Fm) of SPT was used to fit the Esp/Fm versus-temperature curve to determine the energy transition temperature (Tsp) which corresponded to the ductile-brittle transition temperature of the Charpy impact test. The results indicated that the ratio of Esp/Fm could better represent the energy of transition in SPT compared with Esp. The ductile-to-brittle transition temperature of the four different types of materials was measured using the hydrogen charging test by SPT. These four types of materials included the base metal and the weld metal in the as-received state and the base metal and the weld metal in the de-embrittled state. The results showed that there was a degree of temper embrittlement in the base metal and the weld metal after ten years of service at 390 °C. The specimens became slightly more brittle but this was not obvious after hydrogen charging. Because the toughness of the material of the hydrogenation reactor was very good the flat samples of SPT could not characterize the energy transition temperature within the liquid nitrogen temperature. Additionally there was no synergetic effect of temper embrittlement and hydrogen embrittlement found in 3Cr1Mo1/4V steel.
Integration of Wind Energy, Hydrogen and Natural Gas Pipeline Systems to Meet Community and Transportation Energy Needs: A Parametric Study
Apr 2014
Publication
The potential benefits are examined of the “Power-to-Gas” (P2G) scheme to utilize excess wind power capacity by generating hydrogen (or potentially methane) for use in the natural gas distribution grid. A parametric analysis is used to determine the feasibility and size of systems producing hydrogen that would be injected into the natural gas grid. Specifically wind farms located in southwestern Ontario Canada are considered. Infrastructure requirements wind farm size pipeline capacity geographical dispersion hydrogen production rate capital and operating costs are used as performance measures. The model takes into account the potential production rate of hydrogen and the rate that it can be injected into the local gas grid. “Straw man” systems are examined centered on a wind farm size of 100 MW integrating a 16-MW capacity electrolysis system typically producing 4700 kg of hydrogen per day.
Improved Monitoring and Diagnosis of Transformer Solid Insulation Using Pertinent Chemical Indicators
Jul 2021
Publication
Transformers are generally considered to be the costliest assets in a power network. The lifetime of a transformer is mainly attributable to the condition of its solid insulation which in turn is measured and described according to the degree of polymerization (DP) of the cellulose. Since the determination of the DP index is complex and time-consuming and requires the transformer to be taken out of service utilities prefer indirect and non-invasive methods of determining the DP based on the byproduct of cellulose aging. This paper analyzes solid insulation degradation by measuring the furan concentration recently introduced methanol and dissolved gases like carbon oxides and hydrogen in the insulating oil. A group of service-aged distribution transformers were selected for practical investigation based on oil samples and different kinds of tests. Based on the maintenance and planning strategy of the power utility and a weighted combination of measured chemical indicators a neural network was also developed to categorize the state of the transformer in certain classes. The method proved to be able to improve the diagnostic capability of chemical indicators thus providing power utilities with more reliable maintenance tools and avoiding catastrophic failure of transformers.
Techno-economic Assessment of Hydrogen Production from Seawater
Nov 2022
Publication
Population growth and the expansion of industries have increased energy demand and the use of fossil fuels as an energy source resulting in release of greenhouse gases (GHG) and increased air pollution. Countries are therefore looking for alternatives to fossil fuels for energy generation. Using hydrogen as an energy carrier is one of the most promising alternatives to replace fossil fuels in electricity generation. It is therefore essential to know how hydrogen is produced. Hydrogen can be produced by splitting the water molecules in an electrolyser using the abondand water resources which are covering around ⅔ of the Earth's surface. Electrolysers however require high-quality water with conductivity in the range of 0.1–1 μS/cm. In January 2018 there were 184 offshore oil and gas rigs in the North Sea which may be excellent sites for hydrogen production from seawater. The hydrogen production process reported in this paper is based on a proton exchange membrane (PEM) electrolyser with an input flow rate of 300 L/h. A financially optimal system for producing demineralized water from seawater with conductivity in the range of 0.1–1 μS/cm as the input for electrolyser by WAVE (Water Application Value Engine) design software was studied. The costs of producing hydrogen using the optimised system was calculated to be US$3.51/kg H2. The best option for low-cost power generation using renewable resources such as photovoltaic (PV) devices wind turbines as well as electricity from the grid was assessed considering the location of the case considered. All calculations were based on assumption of existing cable from the grid to the offshore meaning that the cost of cables and distribution infrastructure were not considered. Models were created using HOMER Pro (Hybrid Optimisation of Multiple Energy Resources) software to optimise the microgrids and the distributed energy resources under the assumption of a nominal discount rate inflation rate project lifetime and CO2 tax in Norway. Eight different scenarios were examined using HOMER Pro and the main findings being as follows:<br/>The cost of producing water with quality required by the electrolyser is low compared with the cost of electricity for operation of the electrolyser and therefore has little effect on the total cost of hydrogen production (less than 1%).<br/>The optimal solution was shown to be electricity from the grid which has the lowest levelised cost of energy (LCOE) of the options considered. The hydrogen production cost using electricity from the grid was about US$ 5/kg H2.<br/>Grid based electricity resulted in the lowest hydrogen production cost even when costs for CO2 emissions in Norway that will start to apply in 2025 was considered being approximately US$7.7/kg H2.<br/>From economical point of view wind energy was found to be a more economical than solar.
Comparative Assessment of Blue Hydrogen from Steam Methane Reforming, Autothermal Reforming, and Natural Gas Decomposition Technologies for Natural Gas-producing Regions
Jan 2022
Publication
Interest in blue hydrogen production technologies is growing. Some researchers have evaluated the environmental and/or economic feasibility of producing blue hydrogen but a holistic assessment is still needed. Many aspects of hydrogen production have not been investigated. There is very limited information in the literature on the impact of plant size on production and the extent of carbon capture on the cost and life cycle greenhouse gas (GHG) emissions of blue hydrogen production through various production pathways. Detailed uncertainty and sensitivity analyses have not been included in most of the earlier studies. This study conducts a holistic comparative cost and life cycle GHG emissions’ footprint assessment of three natural gas-based blue hydrogen production technologies – steam methane reforming (SMR) autothermal reforming (ATR) and natural gas decomposition (NGD) to address these research gaps. A hydrogen production plant capacity of 607 tonnes per day was considered. For SMR based on the percentage of carbon capture and capture points we considered two scenarios SMR-52% (indicates 52% carbon capture) and SMR-85% (indicates 85% carbon capture). A scale factor was developed for each technology to understand the hydrogen production cost with a change in production plant size. Hydrogen cost is 1.22 1.23 2.12 1.69 2.36 1.66 and 2.55 $/kg H2 for SMR ATR NGD SMR-52% SMR-85% ATR with carbon capture and sequestration (ATR-CCS) and NGD with carbon capture and sequestration (NGD-CCS) respectively. The results indicate that when uncertainty is considered SMR-52% and ATR are economically preferable to NGD and SMR-85%. SMR-52% could outperform ATR-CCS when the natural gas price decreases and the rate of return increases. SMR-85% is the least attractive pathway; however it could outperform NGD economically when CO2 transportation cost and natural gas price decrease. Hydrogen storage cost significantly impacts the hydrogen production cost. SMR-52% SMR-85% ATR-CCS and NGD-CCS have scale factors of 0.67 0.68 0.54 and 0.65 respectively. The hydrogen cost variation with capacity shows that operating SMR-52% and ATR-CCS above hydrogen capacity of 200 tonnes/day is economically attractive. Blue hydrogen from autothermal reforming has the lowest life cycle GHG emissions of 3.91 kgCO2eq/kg H2 followed by blue hydrogen from NGD (4.54 kgCO2eq/kg H2) SMR-85% (6.66 kgCO2eq/kg H2) and SMR-52% (8.20 kgCO2eq/kg H2). The findings of this study are useful for decision-making at various levels.
Nickel-Based Electrocatalysts for Water Electrolysis
Feb 2022
Publication
Currently hydrogen production is based on the reforming process leading to the emission of pollutants; therefore a substitute production method is imminently required. Water electrolysis is an ideal alternative for large-scale hydrogen production as it does not produce any carbon-based pollutant byproducts. The production of green hydrogen from water electrolysis using intermittent sources (e.g. solar and eolic sources) would facilitate clean energy storage. However the electrocatalysts currently required for water electrolysis are noble metals making this potential option expensive and inaccessible for industrial applications. Therefore there is a need to develop electrocatalysts based on earth-abundant and low-cost metals. Nickel-based electrocatalysts are a fitting alternative because they are economically accessible. Extensive research has focused on developing nickel-based electrocatalysts for hydrogen and oxygen evolution. Theoretical and experimental work have addressed the elucidation of these electrochemical processes and the role of heteroatoms structure and morphology. Even though some works tend to be contradictory they have lit up the path for the development of efficient nickel-based electrocatalysts. For these reasons a review of recent progress is presented herein.
Recyclable Metal Fuels for Clean and Compact Zero-carbon Power
Jun 2018
Publication
Metal fuels as recyclable carriers of clean energy are promising alternatives to fossil fuels in a future low-carbon economy. Fossil fuels are a convenient and widely-available source of stored solar energy that have enabled our modern society; however fossil-fuel production cannot perpetually keep up with increasing energy demand while carbon dioxide emissions from fossil-fuel combustion cause climate change. Low-carbon energy carriers with high energy density are needed to replace the multiple indispensable roles of fossil fuels including for electrical and thermal power generation for powering transportation fleets and for global energy trade. Metals have high energy densities and metals are therefore fuels within many batteries energetic materials and propellants. Metal fuels can be burned with air or reacted with water to release their chemical energy at a range of power-generation scales. The metal-oxide combustion products are solids that can be captured and then be recycled using zero-carbon electrolysis processes powered by clean energy enabling metals to be used as recyclable zero-carbon solar fuels or electrofuels. A key technological barrier to the increased use of metal fuels is the current lack of clean and efficient combustor/reactor/engine technologies to convert the chemical energy in metal fuels into motive or electrical power (energy). This paper overviews the concept of low-carbon metal fuels and summarizes the current state of our knowledge regarding the reaction of metal fuels with water to produce hot hydrogen on demand and the combustion of metal fuels with air in laminar and turbulent flames. Many important questions regarding metal-fuel combustion processes remain unanswered as do questions concerning the energy-cycle efficiency and life-cycle environmental impacts and economics of metals as recyclable fuels. Metal fuels can be an important technology option within a future low-carbon society and deserve focused attention to address these open questions.
Bayesian Inference and Uncertainty Quantification for Hydrogen-Enriched and Lean-Premixed Combustion Systems
May 2021
Publication
Development of probabilistic modelling tools to perform Bayesian inference and uncertainty quantification (UQ) is a challenging task for practical hydrogen-enriched and low-emission combustion systems due to the need to take into account simultaneously simulated fluid dynamics and detailed combustion chemistry. A large number of evaluations is required to calibrate models and estimate parameters using experimental data within the framework of Bayesian inference. This task is computationally prohibitive in high-fidelity and deterministic approaches such as large eddy simulation (LES) to design and optimize combustion systems. Therefore there is a need to develop methods that: (a) are suitable for Bayesian inference studies and (b) characterize a range of solutions based on the uncertainty of modelling parameters and input conditions. This paper aims to develop a computationally-efficient toolchain to address these issues for probabilistic modelling of NOx emission in hydrogen-enriched and lean-premixed combustion systems. A novel method is implemented into the toolchain using a chemical reactor network (CRN) model non-intrusive polynomial chaos expansion based on the point collocation method (NIPCE-PCM) and the Markov Chain Monte Carlo (MCMC) method. First a CRN model is generated for a combustion system burning hydrogen-enriched methane/air mixtures at high-pressure lean-premixed conditions to compute NOx emission. A set of metamodels is then developed using NIPCE-PCM as a computationally efficient alternative to the physics-based CRN model. These surrogate models and experimental data are then implemented in the MCMC method to perform a two-step Bayesian calibration to maximize the agreement between model predictions and measurements. The average standard deviations for the prediction of exit temperature and NOx emission are reduced by almost 90% using this method. The calibrated model then used with confidence for global sensitivity and reliability analysis studies which show that the volume of the main-flame zone is the most important parameter for NOx emission. The results show satisfactory performance for the developed toolchain to perform Bayesian inference and UQ studies enabling a robust and consistent process for designing and optimising low-emission combustion systems.
Review of Solid State Hydrogen Storage Methods Adopting Different Kinds of Novel Materials
Aug 2015
Publication
Overview of advances in the technology of solid state hydrogen storage methods applying different kinds of novel materials is provided. Metallic and intermetallic hydrides complex chemical hydride nanostructured carbon materials metal-doped carbon nanotubes metal-organic frameworks (MOFs) metal-doped metal organic frameworks covalent organic frameworks (COFs) and clathrates solid state hydrogen storage techniques are discussed. The studies on their hydrogen storage properties are in progress towards positive direction. Nevertheless it is believed that these novel materials will offer far-reaching solutions to the onboard hydrogen storage problems in near future. The review begins with the deficiencies of current energy economy and discusses the various aspects of implementation of hydrogen energy based economy.
A Manganese Hydride Molecular Sieve for Practical Hydrogen Storage Under Ambient Conditions
Dec 2018
Publication
A viable hydrogen economy has thus far been hampered by the lack of an inexpensive and convenient hydrogen storage solution meeting all requirements especially in the areas of long hauls and delivery infrastructure. Current approaches require high pressure and/or complex heat management systems to achieve acceptable storage densities. Herein we present a manganese hydride molecular sieve that can be readily synthesized from inexpensive precursors and demonstrates a reversible excess adsorption performance of 10.5 wt% and 197 kgH2 m-3 at 120 bar at ambient temperature with no loss of activity after 54 cycles. Inelastic neutron scattering and computational studies confirm Kubas binding as the principal mechanism. The thermodynamically neutral adsorption process allows for a simple system without the need for heat management using moderate pressure as a toggle. A storage material with these properties will allow the DOE system targets for storage and delivery to be achieved providing a practical alternative to incumbents such as 700 bar systems which generally provide volumetric storage values of 40 kgH2 m-3 or less while retaining advantages over batteries such as fill time and energy density. Reasonable estimates for production costs and loss of performance due to system implementation project total energy storage costs roughly 5 times cheaper than those for 700 bar tanks potentially opening doors for increased adoption of hydrogen as an energy vector.
International Association for Hydrogen Safety ‘Research Priorities Workshop’, September 2018, Buxton, UK
Sep 2018
Publication
Hydrogen has the potential to be used by many countries as part of decarbonising the future energy system. Hydrogen can be used as a fuel ‘vector’ to store and transport energy produced in low-carbon ways. This could be particularly important in applications such as heating and transport where other solutions for low and zero carbon emission are difficult. To enable the safe uptake of hydrogen technologies it is important to develop the international scientific evidence base on the potential risks to safety and how to control them effectively. The International Association for Hydrogen Safety (known as IA HySAFE) is leading global efforts to ensure this. HSE hosted the 2018 IA HySAFE Biennial Research Priorities Workshop. A panel of international experts presented during nine key topic sessions: (1) Industrial and National Programmes; (2) Applications; (3) Storage; (4) Accident Physics – Gas Phase; (5) Accident Physics – Liquid/ Cryogenic Behaviour; (6) Materials; (7) Mitigation Sensors Hazard Prevention and Risk Reduction; (8) Integrated Tools for Hazard and Risk Assessment; (9) General Aspects of Safety.<br/>This report gives an overview of each topic made by the session chairperson. It also gives further analysis of the totality of the evidence presented. The workshop outputs are shaping international activities on hydrogen safety. They are helping key stakeholders to identify gaps in knowledge and expertise and to understand and plan for potential safety challenges associated with the global expansion of hydrogen in the energy system.
A Model for Hydrogen Detonation Diffraction or Transmission to a Non-confined Layer
Sep 2021
Publication
One strategy for arresting propagating detonation waves in pipes is by imposing a sudden area enlargement which provides a rapid lateral divergence of the gases in the reaction zone and attenuates the leading shock. For sufficiently small tube diameter the detonation decays to a deflagration and the shock decays to negligible strengths. This is known as the critical tube diameter problem. In the present study we provide a closed form model to predict the detonation quenching for 2D channels. This problem also applies to the transmission of a detonation wave from a confined layer to a weakly-confined layer. Whitham’s geometric shock dynamics coupled with a shock evolution law based on shocks sustained by a constant source obtained by the shock change equations of Radulescu is shown to capture the lateral shock dynamics response to the failure wave originating at the expansion corner. A criterion for successful detonation transmission to open space is that the lateral strain rate provided by the failure wave not exceed the critical strain rate of steady curved detonations. Using the critical lateral strain rate obtained by He and Clavin a closed form solution is obtained for the critical channel opening permitting detonation transmission. The predicted critical channel width is found in excellent agreement with our recent experiments and simulations of diffracting H2/O2/Ar detonations. Model comparison with available data for H2/air detonation diffraction into open space at ambient conditions or for transmission into a weakly confined layer by air is also found in good agreement within a factor never exceeding 2 for the critical opening or layer dimension.
Study of the Microstructural and First Hydrogenation Properties of TiFe Alloy with Zr, Mn and V as Additives
Jul 2021
Publication
In this paper we report the effect of adding Zr + V or Zr + V + Mn to TiFe alloy on microstructure and hydrogen storage properties. The addition of only V was not enough to produce a minimum amount of secondary phase and therefore the first hydrogenation at room temperature under a hydrogen pressure of 20 bars was impossible. When 2 wt.% Zr + 2 wt.% V or 2 wt.% Zr + 2 wt.% V + 2 wt.% Mn is added to TiFe the alloy shows a finely distributed Ti2Fe-like secondary phase. These alloys presented a fast first hydrogenation and a high capacity. The rate-limiting step was found to be 3D growth diffusion controlled with decreasing interface velocity. This is consistent with the hypothesis that the fast reaction is likely to be the presence of Ti2Fe-like secondary phases that act as a gateway for hydrogen.
Determination of Clearance Distances for Venting of Hydrogen Storage
Sep 2005
Publication
This paper discusses the results of computational fluid dynamics (CFD) modelling of hydrogen releases and dispersion outdoors during venting of hydrogen storage in real environment and geometry of a hydrogen refuelling or energy station for a given flow rate and dimensions of vent stack. The PHOENICS CFD software package was used to solve the continuity momentum and concentration equations with the appropriate boundary conditions buoyancy model and turbulence models. Also thermal effects resulting from potential ignition of flammable hydrogen clouds were assessed using TNO “Yellow Book” recommended approaches. The obtained results were then applied to determine appropriate clearance distances for venting of hydrogen storage for contribution to code development and station design considerations. CFD modelling of hydrogen concentrations and TNO-based modelling of thermal effects have proven to be reliable effective and relatively inexpensive tools to evaluate the effects of hydrogen releases.
Effects of Surface on the Flammable Extent of Hydrogen Jets
Sep 2009
Publication
The effect of surfaces on the extent of high pressure horizontal unignited jets of hydrogen and methane is studied using CFD numerical simulations performed with FLACS Hydrogen. Results for constant flow rate through a 6.35 mm PRD from 100 barg and 700 barg storage units are presented for horizontal hydrogen and methane jets. To quantify the effect of a horizontal surface on the jet the jet exit is positioned at various heights above the ground ranging from 0.1 m to 10 m. Free jet simulations are performed for comparison purposes.
Numerical Investigation of Subsonic Hydrogen Jet Release
Sep 2011
Publication
A buoyant round vertical hydrogen jet is investigated using Large Eddy Simulations at low Mach number (M = 0.3). The influence of the transient concentration fields on the extent of the gas envelope with concentrations within the flammability limits is analyzed and their structure are characterized. The transient flammable region has a complex structure that extends up to 30% beyond the time-averaged flammable volume with high concentration pockets that persist sufficiently long for potential ignition. Safety envelopes devised on the basis of simplified time-averaged simulations would need to include a correction factor that accounts for transient incursions of high flammability concentrations.
Alloy and Composition Dependence of Hydrogen Embrittlement Susceptibility in High-strength Steel Fasteners
Jun 2017
Publication
High-strength steel fasteners characterized by tensile strengths above 1100 MPa are often used in critical applications where a failure can have catastrophic consequences. Preventing hydrogen embrittlement (HE) failure is a fundamental concern implicating the entire fastener supply chain. Research is typically conducted under idealized conditions that cannot be translated into know-how prescribed in fastener industry standards and practices. Additionally inconsistencies and even contradictions in fastener industry standards have led to much confusion and many preventable or misdiagnosed fastener failures. HE susceptibility is a function of the material condition which is comprehensively described by the metallurgical and mechanical properties. Material strength has a first-order effect on HE susceptibility which increases significantly above 1200 MPa and is characterized by a ductile--brittle transition. For a given concentration of hydrogen and at equal strength the critical strength above which the ductile–brittle transition begins can vary due to second-order effects of chemistry tempering temperature and sub-microstructure. Additionally non-homogeneity of the metallurgical structure resulting from poorly controlled heat treatment impurities and non-metallic inclusions can increase HE susceptibility of steel in ways that are measurable but unpredictable. Below 1200 MPa non-conforming quality is often the root cause of real-life failures.
Link to document download on Royal Society Website
Link to document download on Royal Society Website
Canadian Hydrogen Safety Program.
Sep 2005
Publication
This paper discusses the rationale structure and contents of the Canadian Hydrogen Safety Program developed by the Codes & Standards Working Group of the Canadian Transportation Fuel Cell Alliance consisting of representatives from industry academia government and regulators. The overall program objective is to facilitate acceptance of the products services and systems of the Canadian Hydrogen Industry by the Canadian Hydrogen Stakeholder Community to facilitate trade ensure fair insurance policies and rates ensure effective and efficient regulatory approval procedures and to ensure that the interests of the general public are accommodated. The Program consists of four projects including Comparative Quantitative Risk Assessment of Hydrogen and Compressed Natural Gas (CNG) Refuelling Stations; Computational Fluid Dynamics (CFD) Modelling Validation Calibration and Enhancement; Enhancement of Frequency and Probability Analysis and Consequence Analysis of Key Component Failures of Hydrogen Systems; and Fuel Cell Oxidant Outlet Hydrogen Sensor Project. The Program projects are tightly linked with the content of the IEA Task 19 Hydrogen Safety. The Program also includes extensive (destructive and non-destructive) testing of hydrogen components.
State-of-the-Art and Research Priorities in Hydrogen Safety
Sep 2013
Publication
On October 16-17 2012 the International Association for Hydrogen Safety (HySafe) in cooperation with the Institute for Energy and Transport of the Joint Research Centre of the European Commission (JRC IET Petten) held a two-day workshop dedicated to Hydrogen Safety Research Priorities. The workshop was hosted by Federal Institute for Materials Research and Testing (BAM) in Berlin Germany. The main idea of the Workshop was to bring together stakeholders who can address the existing knowledge gaps in the area of the hydrogen safety including identification and prioritization of such gaps from the standpoint of scientific knowledge both experimental and theoretical including numerical. The experience highlighting these gaps which was obtained during both practical applications (industry) and risk assessment should serve as reference point for further analysis. The program included two sections: knowledge gaps as they are addressed by industry and knowledge gaps and state-of-the-art by research. In the current work the main results of the workshop are summarized and analysed.
A Turbulent Combustion Model for Ignition of Rapidly Expanding Hydrogen Jets
Mar 2013
Publication
A turbulent combustion model based on the Linear Eddy Model for Large Eddy Simulation (LEM- LES) is currently proposed to study self-ignition events of rapidly expanding hydrogen jets. The model is a one-dimensional treatment of a diffusion-reaction system within each multi-dimensional LES cell. This reduces the expense of solving a complete multi-dimensional problem while preserving micro-scale hotspots and their effects on ignition. The current approach features a Lagrangian description of fluid particles on the sub-grid for increased accuracy. Also Adaptive Mesh Refinement (AMR) is implemented for increased computational efficiency. In this paper the model is validated for various inviscid laminar 1-D mixing and ignition problems shock tube problems flames and detonations.
Numerical Simulation of Combustion of Natural Gas Mixed with Hydrogen in Gas Boilers
Oct 2021
Publication
Hydrogen mixed natural gas for combustion can improve combustion characteristics and reduce carbon emission which has important engineering application value. A casing swirl burner model is adopted to numerically simulate and research the natural gas hydrogen mixing technology for combustion in gas boilers in this paper. Under the condition of conventional air atmosphere and constant air excess coefficient the six working conditions for hydrogen mixing proportion into natural gas are designed to explore the combustion characteristics and the laws of pollution emissions. The temperature distributions composition and emission of combustion flue gas under various working conditions are analyzed and compared. Further investigation is also conducted for the variation laws of NOx and soot generation. The results show that when the boiler heating power is constant hydrogen mixing will increase the combustion temperature accelerate the combustion rate reduce flue gas and CO2 emission increase the generation of water vapor and inhibit the generation of NOx and soot. Under the premise of meeting the fuel interchangeability it is concluded that the optimal hydrogen mixing volume fraction of gas boilers is 24.7%.
Large Eddy Simulations of Asymmetric Turbulent Hydrogen Jets Issuing from Realistic Pipe Geometries
Sep 2017
Publication
In the current study a Large Eddy Simulation strategy is applied to model the dispersion of compressible turbulent hydrogen jets issuing from realistic pipe geometries. The work is novel as it explores the effect of jet densities and Reynolds numbers on vertical buoyant jets as they emerge from the outer wall of a pipe through a round orifice perpendicular to the mean flow within the pipe. An efficient Godunov solver is used and coupled with Adaptive Mesh Refinement to provide high resolution solutions only in areas of interest. The numerical results are validated against physical experiments of air and helium which allows a degree of confidence in analysing the data obtained for hydrogen releases. The results show that the jets investigated are always asymmetric. Thus significant discrepancies exist when applying conventional round jet assumptions to determine statistical properties associated with gas leaks from pipelines.
HIAD – Hydrogen Incident and Accident Database
Sep 2011
Publication
The Hydrogen Incident and Accident Database (HIAD) is being developed as a repository of systematic data describing in detail hydrogen-related undesired events (incidents or accidents). It is an open web-based information system serving various purposes such as a data source for lessons learnt risk communication and partly risk assessment. The paper describes the features of the three HIAD modules – the Data Entry Module (DEM) the Data Retrieval Module (DRM) and the Data Analysis Module (DAM) – and the potential impact the database may have on hydrogen safety. The importance of data quality assurance process is also addressed.
Modelling Of Hydrogen Explosion on a Pressure Swing Adsorption Facility
Sep 2011
Publication
Computational fluid dynamic simulations have been performed in order to study the consequences of a hydrogen release from a pressure swing adsorption installation operating at 30 barg. The simulations were performed using FLACS-Hydrogen software from GexCon. The impact of obstruction partial confinement leak orientation and wind on the explosive cloud formation (size and explosive mass) and on explosion consequences is investigated. Overpressures resulting from ignition are calculated as a function of the time to ignition.
Application of Risk Assessment Approach on a Hydrogen Station
Sep 2013
Publication
An accident modelling approach is used to assess the safety of a hydrogen station as part of a ground transportation network. The method incorporates prevention barriers associated to human factors management and organizational failures in a risk assessment framework. Failure probabilities of these barriers and end-states events are predicted using Fault Tree Analysis and Event Tree Analysis respectively. Results from the case study considered revealed the capability of the proposed method in estimating the likelihood of various outcomes as well as predicting the future probability. In addition the scheme offers opportunity to provide dynamic adjustment by updating the failure probability with actual plant data. Results from the analysis can be used to plan maintenance and management of change as required by the plant condition.
A Review of the Status of Fossil and Renewable Energies in Southeast Asia and Its Implications on the Decarbonization of ASEAN
Mar 2022
Publication
The ten nations of Southeast Asia collectively known as ASEAN emitted 1.65 Gtpa CO2 in 2020 and are among the most vulnerable nations to climate change which is partially caused by anthropogenic CO2 emission. This paper analyzes the history of ASEAN energy consumption and CO2 emission from both fossil and renewable energies in the last two decades. The results show that ASEAN’s renewable energies resources range from low to moderate are unevenly distributed geographically and contributed to only 20% of total primary energy consumption (TPEC) in 2015. The dominant forms of renewable energies are hydropower solar photovoltaic and bioenergy. However both hydropower and bioenergy have substantial sustainability issues. Fossil energies depend heavily on coal and oil and contribute to 80% of TPEC. More importantly renewable energies’ contribution to TPEC has been decreasing in the last two decades despite the increasing installation capacity. This suggests that the current rate of the addition of renewable energy capacity is inadequate to allow ASEAN to reach net-zero by 2050. Therefore fossil energies will continue to be an important part of ASEAN’s energy mix. More tools such as carbon capture and storage (CCS) and hydrogen will be needed for decarbonization. CCS will be needed to decarbonize ASEAN’s fossil power and industrial plants while blue hydrogen will be needed to decarbonize hard-to-decarbonize industrial plants. Based on recent research into regional CO2 source-sink mapping this paper proposes six large-scale CCS projects in four countries which can mitigate up to 300 Mtpa CO2 . Furthermore this paper identifies common pathways for ASEAN decarbonization and their policy implications.
Two-stage Model Predictive Control for a Hydrogen-based Storage System Paired to a Wind Farm Towards Green Hydrogen Production for Fuel Cell Electric Vehicles
Jul 2022
Publication
This study proposes a multi-level model predictive control (MPC) for a grid-connected wind farm paired to a hydrogen-based storage system (HESS) to produce hydrogen as a fuel for commercial road vehicles while meeting electric and contractual loads at the same time. In particular the integrated system (wind farm + HESS) should comply with the “fuel production” use case as per the IEA-HIA report where the hydrogen production for fuel cell electric vehicles (FCEVs) has the highest unconditional priority among all the objectives. Based on models adopting mixed-integer constraints and dynamics the problem of external hydrogen consumer requests optimal load demand tracking and electricity market participation is solved at different timescales to achieve a long-term plan based on forecasts that then are adjusted at real-time. The developed controller will be deployed onto the management platform of the HESS which is paired to a wind farm established in North Norway within the EU funded project HAEOLUS. Numerical analysis shows that the proposed controller efficiently manages the integrated system and commits the equipment so as to comply with the requirements of the addressed scenario. The operating costs of the devices are reduced by 5% which corresponds to roughly 300 commutations saved per year for devices.
Prospects and Technical Challenges in Hydrogen Production through Dry Reforming of Methane
Mar 2022
Publication
Environmental issues related to greenhouse gases (GHG) emissions have pushed the development of new technologies that will allow the economic production of low-carbon energy vectors such as hydrogen (H2 ) methane (CH4 ) and liquid fuels. Dry reforming of methane (DRM) has gained increased attention since it uses CH4 and carbon dioxide (CO2 ) which are two main greenhouse gases (GHG) as feedstock for the production of syngas which is a mixture of H2 and carbon monoxide (CO) and can be used as a building block for the production of fuels. Since H2 has been identified as a key enabler of the energy transition a lot of studies have aimed to benefit from the environmental advantages of DRM and to use it as a pathway for a sustainable H2 production. However there are several challenges related to this process and to its use for H2 production such as catalyst deactivation and the low H2/CO ratio of the syngas produced which is usually below 1.0. This paper presents the recent advances in the catalyst development for H2 production via DRM the processes that could be combined with DRM to overcome these challenges and the current industrial processes using DRM. The objective is to assess in which conditions DRM could be used for H2 production and the gaps in literature data preventing better evaluation of the environmental and economic potential of this process.
A Comparative Study of CFD-Modelling for Lean Premixed Hydrogen Deflagrations in Large-scale Vented Vessels
Sep 2021
Publication
Hydrogen combustion inside a post-accident nuclear reactor containment may pose a challenge to the containment integrity which could alter the fission-product release source term to the public. Combustion-generated overpressures may be relieved by venting to adjacent compartments through relief panels or existing openings. Thus an improved understanding of the propagation of lean hydrogen deflagrations in inter-connected compartments is essential for the development of appropriate management strategies. GOTHIC is a general purpose lumped parameter thermal-hydraulic code for solving multi-phase compressible flows which is accepted as an industry-standard code for containment safety analyses. Following the Fukushima accident the application of three-dimensional computational fluid dynamics methods to high-fidelity detailed analysis of hydrogen combustion processes has become more widespread. In this study a recently developed large-eddy-simulation (LES) capability is applied to the prediction of lean premixed hydrogen deflagrations in large-scale vented vessels of various configurations. The LES predictions are compared with GOTHIC predictions and experimental data obtained from the large-scale vented combustion test facility at the Canadian Nuclear Laboratories. The LES methodology makes use of a flamelet- or a progress-variable-based combustion model. An empirical burning velocity model is combined with an advanced finite-volume framework and a mesh-independent subfilter-scale model. Descriptions of the LES and GOTHIC modelling approaches used to simulate the hydrogen reactive flows in the vented vessels along with the experimental data sets are given. The potential and limitations of the lumped parameter and LES approaches for accurately describing lean premixed hydrogen deflagrations in vented vessels are discussed.
No more items...