Safety

All vehicular high-pressure hydrogen tanks are equipped with thermally-activated pressure relief devices (TPRDs) required by Global Technical Regulation. This safety device significantly reduces the risk of tank catastrophic rupture by venting the hydrogen pressure outside. However the released flammable hydrogen raises additional safety problems. Japan Automobile Research Institute has demonstrated that in the vehicle fire event once the TPRD opens the hydrogen fires will engulf the whole vehicle making it difficult for the drivers and passenger to evacuate from the vehicle. This paper designs a new safety system to solve the evacuation problem. The safety system includes a rotatable pressure relief device with a motor a sensory system that consists of infrared sensors ultrasonic radar and temperature sensors a central control unit and an alarm device. The new design of the pressure relief device allows the system actively adjusting the release direction towards void open space outside the vehicle to minimize the risks of hydrogen fires. The infrared sensors located at the roof of the vehicles collect info inside the vehicle and the ultrasonic radar detect the region outside the vehicle. Temperature sensors tell when to trigger the alarm and set the motor in standby mode and the central control unit determines where to rotate based on the info from the infrared sensors and ultrasonic radars. A control strategy is also proposed to operate the safety system in an appropriate way. The cost-benefit analysis show that the new safety system can significantly reduce the risks of intended hydrogen releases from onboard pressure relief devices with total cost increases by less than 1% of the vehicle cost making it a good cost-effective engineering solution.

The authors presented a basic mathematical model for estimating peak overpressure attained in vented explosions of hydrogen in a previous study (Sinha et al. [1]). The model focussed on idealized cases of hydrogen and was not applicable for realistic accidental scenarios like presence of obstacles initial turbulent mixture etc. In the present study the underlying framework of the model is reformulated to overcome these limitations. The flame shape computations are simplified. A more accurate and simpler formulation for venting is also introduced. Further by using simplifying assumptions and algebraic manipulations the detailed model consisting of several equations is reduced to a single equation with only four parameters. Two of these parameters depend only on fuel properties and a standard table provided in the Appendix can be used. Therefore to compute the overpressure only the two parameters based on enclosure geometry need to be evaluated. This greatly simplifies the model and calculation effort. Also since the focus of previous investigation was hydrogen properties of hydrocarbon fuels which are much more widely used were not accounted for. The present model also accounts for thermo-physical properties of hydrocarbons and provides table for fuel parameters to be used in the final equation for propane and methane. The model is also improved by addition of different sub-models to account for various realistic accidental scenarios. Moreover no adjustable parameters are used; the same equation is used for all conditions and all gases. Predictions from this simplified model are compared with experimentally measured values of overpressure for hydrogen and hydrocarbons and found to be in good agreement. First the results from experiments focussing on idealized conditions of uniformly mixed fuel in an empty enclosure under quiescent conditions are considered. Further the model applicability is also tested for realistic conditions of accidental explosion consisting of obstacles inside the enclosure non-uniform fuel distribution initial turbulent mixture etc. For all the cases tested the new simple model is found to produce reasonably good predictions.

According to the Global technical regulation on hydrogen and fuel cell vehicles (FCV) fuel cell discharge system at the vehicle exhaust system`s point of discharge the hydrogen concentration level shall not exceed 4 % average by volume during any moving three-second time interval during normal operation including start-up and shut down [1]. FC stack need to washout by the concentrated hydrogen as the purge gas and how to exhaust gas without exceeding 4 % is the most concerns. Also how to measure hydrogen pulse of millisecond in exhaust is also the rising up issue. In this paper model of FCV hydrogen discharge system was composed and variety of simple experiments were carried out to control the H2 concentration and release. In the case which the semiconductor sensor with porous material (average size less than quench distance) were applied to check H2 concentration the short pulse of high concentration of H2 in millisecond was hard to find. In this experiment the simple exhaust gas model H2/N2 flow was used instead of Air/H2. In the exhaust gas test experiment was conducted under the atmospheric condition in room temperature with small pressure difference and the fast solenoid valve to create quick hydrogen control. Most of the experiments except the turbulent flow experiments laminar flow is expected to be dominated when steady state condition is satisfied but the most result discussed here is the measurement of H2 concentration during the start point at the time of discharge within seconds. The results showed when H2 was added to N2 flow the boundary layer between N2 and H2 contained the high concentration of H2 at the initial wave front and decrease to reach steady state. This H2 pulse is typical in the FCV exhaust gas and topics of this paper.

Catalytic hydrogen-oxygen recombination is a non-traditional method to limit hydrogen accumulation and prevent combustion in the hydrogen industry. Outside of conventional use in the nuclear power industry this hydrogen safety technology can be applied when traditional hydrogen mitigation methods (i.e. active and natural ventilation) are not appropriate or when a back-up system is required. In many of these cases it is desirable for hydrogen to be removed without the use of power or other services which makes catalytic hydrogen recombination attractive. Instances where catalytic recombination of hydrogen can be utilized as a stand-alone or back-up measure to prevent hydrogen accumulation include radioactive waste storage (hydrogen generated from water radiolysis or material corrosion) battery rooms hydrogen-cooled generators hydrogen equipment enclosures etc.<br/>Water tolerant hydrogen-oxygen recombiner catalysts for non-nuclear applications have been developed at Canadian Nuclear Laboratories (CNL) through a program in which catalyst materials were selected prepared and initially tested in a spinning-basket type reactor to benchmark the catalyst’s performance with respect to hydrogen recombination in dry and humid conditions. Catalysts demonstrating high activity for hydrogen recombination were then selected and tested in trickle-bed and gas phase recombiner systems to determine their performance in more typical deployment conditions. Future plans include testing of selected catalysts after exposure to specific poisons to determine the catalysts’ tolerance for such poisons.

The paper describes a lumped-parameter model for vented deflagrations of localised and layered fuel air mixtures. Theoretical model background is described to allow insight into the model development with focus on lean mixtures and overpressures significantly below 0.1 MPa for protection of low strength equipment and buildings. Phenomena leading to combustion augmentation was accounted based on conclusions of recent CFD studies. Technique to treat layered mixtures with concentration gradient is demonstrated. The model is validated against 25 vented deflagration experiments with lean non-uniform and layered hydrogen-air mixtures performed in Health and Safety Laboratory (UK) and Karlsruhe Institute of Technology (Germany).

Liquid hydrogen (LH2) compared to compressed gaseous hydrogen offers advantages for large-scale transport and storage of hydrogen with higher densities. Although the gas industry has good experience with LH2 only little experience is available for the new applications of LH2 as an energy carrier. Therefore the European FCH JU funded project PRESLHY conducted pre-normative research for the safe use of cryogenic LH2 in non-industrial settings. The central research consisted of a broad experimental program combined with analytical work modelling and simulations belonging to the three key phenomena of the accident chain: release and mixing ignition and combustion. The presented results improve the general understanding of the behavior of LH2 in accidents and provide some design guidelines and engineering tools for safer use of LH2. Recommendations for improvement of current international standards are derived.

High-strength steels with yield strength of 960 MPa are susceptible to hydrogen-assisted cracking (HAC) during welding processing. In the present paper the implant test is used to study HAC in a quenched and tempered steel S960QL and a high-strength steel produced by thermo-mechanical controlled process S960MC. Welding is performed using the gas-metal arc welding process. Furthermore diffusible hydrogen concentration (H_D) in arc weld metal is determined. Based on the implant test results lower critical stress (LCS) for complete fracture critical implant stress (σ_krit) for crack initiation and embrittlement index (EI) are determined. At HD of 1.66 ml/100 g LCS is 605 MPa and 817 MPa for S960QL and S960MC respectively. EI is 0.30 and 0.46 for S960QL and S960MC respectively. Fracture surfaces of S960QL show higher degradation with reduced deformation. Both higher EI of S960MC and fractography show better resistance to HAC in the HAZ of S960MC compared to S960QL.

Purpose- To present an overview of the research and development carried out in a European funded framework 7 (FP7) project called SafeHPower for the implementation of neutron radiography to inspect fatigue cracks in vehicle and storage hydrogen fuel tanks. Project background– Hydrogen (H2) is the most promising replacement fuel for road transport due to its abundance efficiency low carbon footprint and the absence of harmful emissions. For the mass market of hydrogen to take off the safety issue surrounding the vehicle and storage hydrogen tanks needs to be addressed. The problem is the residual and additional stresses experienced by the tanks during the continuous cyclic loading between ambient and storage pressure which can result in the development of fatigue cracks. Steel tanks used as storage containers at service stations and depots and/or the composite tanks lined with steel are known to suffer from hydrogen embrittlement (HE). Another issue is the explosive nature of hydrogen (when it is present in the 18-59% range) where it is mixed with oxygen which can lead to catastrophic consequences including loss of life. Monitoring systems that currently exist in the market impose visual examination tests pressure tests and hydrostatic tests after the tank installation [1] [2]. Three inspection systems have been developed under this project to provide continuous monitoring solutions. Approach and scope- One of the inspection systems based on the neutron radiography (NR) technology that was developed in different phases with the application of varied strategies has been presented here. Monte Carlo (MCNP) simulation results to design and develop a bespoke collimator have been presented. A limitation of using an inertial electrostatic Deuterium-Tritium (D-T) pulsed neutron generator for fast neutron radiography has been discussed. Radiographs from the hydrogen tank samples obtained using thermal neutrons from a spallation neutron source at ISIS Rutherford laboratory UK have been presented. Furthermore radiograph obtained using thermal neutrons from a portable D-T neutron generator has been presented. In conclusion a proof in principle has been made to show that the defects in the hydrogen fuel tank can be detected using thermal neutron radiography.

Hydrogen is one of the most suitable candidates in replacing fossil fuels. However storage issues due to its very low density under ambient conditions are encountered in many applications. The liquefaction process can overcome such issues by increasing hydrogen’s density and thus enhancing its storage capacity. A boiling liquid expanding vapour explosion (BLEVE) is a phenomenon in liquefied gas storage systems. It is a physical explosion that might occur after the catastrophic rupture of a vessel containing a liquid with a temperature above its boiling point at atmospheric pressure. Even though it is an atypical accident scenario (low probability) it should be always considered due to its high yield consequences. For all the above-mentioned reasons the BLEVE phenomenon for liquid hydrogen (LH2) vessels was studied using the CFD methodology. Firstly the CFD model was validated against a well-documented CO2 BLEVE experiment. Secondly hydrogen BLEVE cases were simulated based on tests that were conducted in the 1990s on LH2 tanks designed for automotive purposes. The parametric CFD analysis examined different filling degrees initial pressures and temperatures of the tank content with the aim of comprehending to what extent the initial conditions influence the blast wave. Good agreement was shown between the simulation outcomes and the LH2 bursting scenario tests results.

Hydrogen fuel cell vehicle (HFCV) technology poses great promise as an alternative to significantly reduce the environmental impact of the transport sector’s emissions. However hydrogen fuel cell technology is relatively new therefore confirmation of the reliability and safety analysis is still required particularly for fire scenarios within confined spaces such as tunnels. This study applied the computational fluid dynamics (CFD) simulations in conjunction with probabilistic calculation methods to determine the associated thermal risk of a hydrogen jet fire in a tunnel and its dependency on scenarios with different tunnel slopes longitudinal and transverse ventilation velocities and fire positions. A large-scale model of 102 m in which the effects of outlined parameter variations on the severity of the fire incident were analysed. It is found that both tunnel ventilation techniques and slope were critical for the effective ejection of accumulated heat. With ventilation playing a primary role in the ejection of heat and gas and slope ensuring the stability of the ejected heat probabilities of thermal burns were found to be reduced by up to approximately 35% with a strong suggestion of critical combinations to further reduce the dangers of hydrogen tunnel fires.