United Kingdom

Unignited hydrogen release in underground parking could be considered inherently safer if the safety strategy to avoid the formation of the flammable hydrogen-air mixture under a ceiling is followed. This strategy excludes destructive deflagrative combustion and associated pressure and thermal effects in the case of ignition. This paper aims at understanding the effects of the thermally activated pressure relieve device (TPRD) diameter and direction of release on the build-up of hydrogen flammable concentration under the ceiling in the presence of mechanical ventilation required for underground parking. The study employs the similarity law for hydrogen jet concentration decay in a free under-expanded jet to find the lower limit of TPRD diameter that excludes the formation of a flammable mixture under the ceiling during upward release. This approach is conservative and does not include the effect of mechanical ventilation providing flow velocity around a few meters per second which is significantly below velocities in hydrogen momentum-dominated under-expanded jets. Hydrogen releases downwards under a vehicle at different angles and with different air velocities due to mechanical ventilation were investigated using computational fluid dynamics (CFD). The joint effect of TPRD diameter release direction and mechanical ventilation is studied. TPRD diameters for the release of hydrogen upwards and downwards preventing the creation of flammable hydrogen-air mixture under the parking ceiling are defined for different ceiling heights and locations of TPRD above the floor. Recommendations to the design of TPRD devices to underpin the safe introduction of hydrogen fuelled vehicles in currently existing underground parking and infrastructure are formulated."

Fuel transition can decarbonize shipping and help meet IMO 2050 goals. In this paper HFO with CCS LNG with CCS bio-methanol biodiesel hydrogen ammonia and electricity were studied using empirical ship design models from a fleet-level perspective and at the Tank-ToWake level to assist operators technology developers and policy makers. The cargo attainment rate CAR (i.e. cargo that must be displaced due to the low-C propulsion system) the ES (i.e. TTW energy needed per ton*n.m.) the CS (economic cost per ton*n.m.) and the carbon intensity index CII (gCO2 per ton*n.m.) were calculated so that the potential of the various alternatives can be compared quantitatively as a function of different criteria. The sensitivity of CAR towards ship type fuel type cargo type and voyage distance were investigated. All ship types had similar CAR estimates which implies that considerations concerning fuel transition apply equally to all ships (cargo containership tankers). Cargo type was the most sensitive factor that made a ship either weight or volume critical indirectly impacting on the CAR of different fuels; for example a hydrogen ship is weight-critical and has 2.3% higher CAR than the reference HFO ship at 20000 nm. Voyage distance and fuel type could result in up to 48.51% and 11.75% of CAR reduction. In addition to CAR the ES CS and CII for a typical mission were calculated and it was found that HFO and LNG with CCS gave about 20% higher ES and CS than HFO and biodiesel had twice the cost while ammonia methanol and hydrogen had 3–4 times the CS of HFO and electricity about 20 times suggesting that decarbonisation of the world’s fleet will come at a large cost. As an example of including all factors in an effort to create a normalized scoring system an equal weight was allocated to each index (CAR ES CS and CII). Biodiesel achieved the highest score (80%) and was identified as the alternative with the highest potential for a deep-seagoing containership followed by ammonia hydrogen bio-methanol and CCS. Electricity has the lowest normalized score of 33%. A total of 100% CAR is achievable by all alternative fuels but with compromises in voyage distance or with refuelling. For example a battery containership carrying an equal amount of cargo as an HFO-fuelled containership can only complete 13% of the voyage distance or needs refuelling seven times to complete 10000 n.m. The results can guide decarbonization strategies at the fleet level and can help optimise emissions as a function of specific missions.

On 20 December 2021 the Department for Business Energy and Industrial Strategy (BEIS) launched a Call for Evidence (CfE) on enabling or requiring hydrogen-ready industrial boiler equipment. The aim was to gather evidence from a broad range of UK manufacturers industrial end-users supply chain participants and other experts to enable the development of proposals. The CfE was open for 12 weeks closing on 14 March 2022. The CfE followed the publication of the UK Hydrogen Strategy on 17 August 2021. In the Strategy government committed to run a CfE on hydrogen-ready industrial equipment by theend of 2022. The published CfE focussed on industrial boilers due to their widespread use and because BEIS analysis indicates a significant proportion of the demand for hydrogen in industry will come from this equipment category. Furthermore the technology required for hydrogen boilers is relatively advanced and more standardised than for other types of industrial<br/>equipment. For these reasons industrial boiler equipment presents a good test case for hydrogen-ready industrial equipment more broadly.<br/>The CfE contained the following three sections:<br/>• The opportunity for hydrogen-ready industrial boilers<br/>• The role for government to support hydrogen-ready industrial boiler equipment<br/>• The role of the supply chain and economic opportunities for the UK<br/>Respondents were asked to support their answers with evidence relating to their business product or sector published literature studies or to their broader expertise. To raise awareness of the CfE BEIS officials held two online webinars on 1 February 2022 and 3 February 2022. These were open to boiler manufacturers industrial end-users supply chain participants trade associations professional bodies and any other person(s) with an interest in the area.<br/>To build on evidence gathered through the CfE BEIS commissioned an independent study from Arup and Kiwa Gastec to further examine whether government should enable or require hydrogen-ready industrial boiler equipment. This study investigated the following topics:<br/>• definitions of hydrogen-readiness for industrial boilers<br/>• comparisons of the cost and resource requirement to install and convert hydrogen-ready industrial boiler equipment<br/>• industrial boiler supply chain capacity for conversion to hydrogen<br/>• estimates of the UK industrial boiler population<br/>The final report for this study has been published alongside the government response to the call for evidence. The conclusions and recommendations of that report do not necessarily represent the view of BEIS.

As countries seek ways to meet climate change commitments hydrogen fuel offers a low-carbon alternative for sectors where battery electrification may not be viable. Blending hydrogen with fossil fuels requires only modest technological adaptation however since combustion is retained nitrogen oxides (NOx) emissions remain a potential disbenefit. We review the potential air quality impacts arising from the use of hydrogen–diesel blends in heavy-duty diesel engines a powertrain which lends itself to hydrogen co-fuelling. Engine load is identified as a key factor influencing NOx emissions from hydrogen–diesel combustion in heavy-duty engines although variation in other experimental parameters across studies complicates this relationship. Combining results from peer-reviewed literature allows an estimation to be made of plausible NOx emissions from hydrogen–diesel combustion relative to pure-diesel combustion. At 0–30% engine load which encompasses the average load for mobile engine applications NOx emissions changes were in the range 59 to +24% for a fuel blend with 40 e% hydrogen. However at 50–100% load which approximately corresponds to stationary engine applications NOx emissions changes were in the range 28 to +107%. Exhaust gas recirculation may be able to reduce NOx emissions at very high and very low loads when hydrogen is blended with diesel and existing exhaust aftertreatment technologies are also likely to be effective. Recent commercial reporting on the development of hydrogen and hydrogen–diesel dual fuel combustion in large diesel engines are also summarised. There is currently some disconnection between manufacturer reported impacts of hydrogen-fuelling on NOx emissions (always lower emissions) and the conclusions drawn from the peer reviewed literature (frequently higher emissions).

The transition to a low-carbon energy system can be depicted as a “great reconfiguration” from a socio-technical perspective that carries the risk of impact shifts. Electrification with the objective of achieving rapidly deep decarbonisation must be accompanied by effective efficiency and flexibility measures. Hydrogen can be a preferred option in the decarbonisation process where electrification of end-uses is difficult or impractical as well as for long-term storage in energy infrastructure characterised by a large penetration of renewable energy sources. Notwithstanding the current uncertainties regarding costs environmental impact and the inherent difficulties of increasing rapidly supply capacity hydrogen can represent a solution to be used in multi-energy systems with combined heat and power (CHP) in particular in urban energy districts. In fact while achieving carbon savings with natural gas fuelled CHP is not possible when low grid carbon intensity factors are present it may still be possible to use it to provide flexibility services and to reduce emissions further with switch from natural gas to hydrogen. In this paper a commercially established urban district energy scheme located in Southampton (United Kingdom) is analysed with the goal of exploring potential variations in its energy demand. The study proposes the use of scalable data-driven methods and probabilistic simulation to generate seasonal energy demand patterns representing the potential short-term and long-term evolution of the energy district.

Hydrogen as a suitable and clean energy carrier has been long considered a primary fuel or in combination with other conventional fuels such as gasoline and diesel. Since the density of hydrogen is very low in port fuel-injection configuration the engine’s volumetric efficiency reduces due to the replacement of hydrogen by intake air. Therefore hydrogen direct in-cylinder injection (injection after the intake valve closes) can be a suitable solution for hydrogen utilization in spark ignition (SI) engines. In this study the effects of hydrogen direct injection with different hydrogen energy shares (HES) on the performance and emissions characteristics of a gasoline port-injection SI engine are investigated based on reactive computational fluid dynamics. Three different injection timings of hydrogen together with five different HES are applied at low and full load on a hydrogen– gasoline dual-fuel SI engine. The results show that retarded hydrogen injection timing increases the concentration of hydrogen near the spark plug resulting in areas with higher average temperatures which led to NOX emission deterioration at −120 Crank angle degree After Top Dead Center (CAD aTDC) start of injection (SOI) compared to the other modes. At −120 CAD aTDC SOI for 50% HES the amount of NOX was 26% higher than −140 CAD aTDC SOI. In the meanwhile an advanced hydrogen injection timing formed a homogeneous mixture of hydrogen which decreased the HC and soot concentration so that −140 CAD aTDC SOI implied the lowest amount of HC and soot. Moreover with the increase in the amount of HES the concentrations of CO CO2 and soot were reduced. Having the HES by 50% at −140 CAD aTDC SOI the concentrations of particulate matter (PM) CO and CO2 were reduced by 96.3% 90% and 46% respectively. However due to more complete combustion and an elevated combustion average temperature the amount of NOX emission increased drastically.

There is renewed interest in hydrogen as an alternative fuel for aero engines due to their perceived environmental and performance benefits compared to jet fuel. This paper presents a cycle thermal performance energy and creep life assessment of hydrogen compared with jet fuel using a turbofan aero engine. The turbofan cycle performance was simulated using a code developed by the authors that allows hydrogen and jet fuel to be selected as fuel input. The exergy assessment uses both conservations of energy and mass and the second law of thermodynamics to understand the impact of the fuels on the exergy destruction exergy efficiency waste factor ratio environmental effect factor and sustainability index for a turbofan aero engine. Finally the study looks at a top-level creep life assessment on the high-pressure turbine hot section influenced by the fuel heating values. This study shows performance (64% reduced fuel flow rate better SFC) and more extended blade life (15% increase) benefits using liquefied hydrogen fuel which corresponds with other literary work on the benefits of LH2 over jet fuel. This paper also highlights some drawbacks of hydrogen fuel based on previous research work and gives recommendations for future work aimed at maturing the hydrogen fuel concept in aviation.

Polymer Electrolyte Membrane fuel cell (PEMFC) uses hydrogen as fuel to generate electricity and by-product water at relatively low operating temperatures which is environmentally friendly. Since PEMFC performance characteristics are inherently nonlinear and related predicting the best performance for the different operating conditions is essential to improve the system’s efficiency. Thus modeling using artificial neural networks (ANN) to predict its performance can significantly improve the capabilities of handling multi-variable nonlinear performance of the PEMFC. This paper predicts the electrical performance of a PEMFC stack under various operating conditions. The four input terms for the 5 W PEMFC include anode and cathode pressures and flow rates. The model performances are based on ANN using two different learning algorithms to estimate the stack voltage and power. The models have shown consistently to be comparable to the experimental data. All models with at least five hidden neurons have coefficients of determination of 0.95 or higher. Meanwhile the PEMFC voltage and power models have mean squared errors of less than 1 × 10−3 V and 1 × 10−3 W respectively. Therefore the model results demonstrate the potential use of ANN into the implementation of such models to predict the steady state behavior of the PEMFC system (not limited to polarization curves) for different operating conditions and help in the optimization process for achieving the best performance of the system.

There is worldwide interest in transporting hydrogen using both new pipelines and pipelines converted from natural gas service. Laboratory tests investigating the effect of hydrogen on the mechanical properties of pipeline steels have shown that even low partial pressures of hydrogen can substantially reduce properties such as reduction in area and fracture toughness and increase fatigue crack growth rates. However qualitative arguments suggest that the effects on pipelines may not be as severe as predicted from the small scale tests. If the trends seen in laboratory tests do occur in service there are implications for the assessment of damage such as volumetric corrosion dents and mechanical interference. Most pipeline damage assessment methods are semi-empirical and have been calibrated with data from full scale tests that did not involve hydrogen. Hence the European Pipeline Research Group (EPRG) commissioned a study to investigate damage assessment methods in the presence of hydrogen. Two example pipeline designs were considered both were assessed assuming a modern high performance material and an older material. From these analyses the numerical results show that the high toughness material will tolerate damage even if the properties are degraded by hydrogen exposure. However low toughness materials may not be able to tolerate some types of severe damage. If the predictions are realistic operators may have to repair more damage or reduce operating pressures. Furthermore damage involving cracking may not Page 2 of 22 satisfy the ASME B31.12 requirements for preventing time dependent crack growth. Further work is required to determine if the effects predicted using small scale laboratory test data will occur in practice.

Energy supplies that are safe environmentally friendly dependable and cost-effective are important for society's long-term growth and improved living standards though political social and economic barriers may inhibit their availability. Constantly increasing energy demand is induced by substantial population growth and economic development putting an increasing strain on fossil fuel management and sustainability which account for a major portion of this rising energy demand and moreover creates difficulties because of greenhouse gas emissions growth and the depletion of resources. Such impediments necessitate a global shift away from traditional energy sources and toward renewables. Aside from its traditional role is viewed as a promising energy vector and is gaining international attention as a promising fuel path as it provides numerous benefits in use case scenarios and unlike other synthesized carbon-based fuels could be carbon-free or perhaps even negative on a life-cycle criterion. Hydrogen ( ) is one of the most significant chemical substances on earth and can be obtained as molecular dihydrogen through various techniques from both non-renewable and renewable sources. The drive of this paper is to deliver a technological overview of hydrogen production methods. The major challenges development and research priorities and potential prospects for production was discussed.