Publications
Development of a Model Evaluation Protocol for CFD Analysis of Hydrogen Safety Issues – The SUSANA Project
Oct 2015
Publication
The “SUpport to SAfety aNAlysis of Hydrogen and Fuel Cell Technologies (SUSANA)” project aims to support stakeholders using Computational Fluid Dynamics (CFD) for safety engineering design and assessment of FCH systems and infrastructure through the development of a model evaluation protocol. The protocol covers all aspects of safety assessment modelling using CFD from release through dispersion to combustion (self-ignition fires deflagrations detonations and Deflagration to Detonation Transition - DDT) and not only aims to enable users to evaluate models but to inform them of the state of the art and best practices in numerical modelling. The paper gives an overview of the SUSANA project including the main stages of the model evaluation protocol and some results from the on-going benchmarking activities.
Hydrogen Storage: Recent Improvements and Industrial Perspectives
Sep 2017
Publication
Efficient storage of hydrogen is crucial for the success of hydrogen energy markets (early markets as well as transportation market). Hydrogen can be stored either as a compressed gas a refrigerated liquefied gas a cryo-compressed gas or in hydrides. This paper gives an overview of hydrogen storage technologies and details the specific issues and constraints related to the materials behaviour in hydrogen and conditions representative of hydrogen energy uses. It is indeed essential for the development of applications requiring long-term performance to have good understanding of long-term behaviour of the materials of the storage device and its components under operational loads.
Numerical Study of the Detonation Benchmark using GASFLOW-MPI
Sep 2019
Publication
Hydrogen has been widely used as an energy carrier in recent years. It should a better understand of the potential hydrogen risk under the unintended release of hydrogen scenario since the hydrogen could be ignited in a wide range of hydrogen concentrations in the air and generate a fast flame speed. During the accidental situation the hydrogen-air detonation may happen in the large-scale space which is viewed as the worst case state of affairs. GASFLOW-MPI is a powerful CFD-based numerical tool to predict the complicated hydrogen turbulent transport and combustion dynamics behaviours in the three-dimensional large-scale industrial facility. There is a serious of well-developed physical models in GASFLOW-MPI to simulate a wide spectrum of combustion behaviours ranging from slow flames to deflagration-to-detonation transition and even to detonation. The hydrogen–air detonation experiment which was carried out at the RUT tunnel facility is a well-known benchmark to validate the combustion model. In this work a numerical study of the detonation benchmark at RUT tunnel facility is performed using the CFD code GASFLOW-MPI. The complex shock wave structures in the detonation are captured accurately. The experimental pressure records and the simulated pressure dynamics are compared and discussed.
Assessing the Viability of the ACT Natural Gas Distribution Network for Reuse as a Hydrogen Distribution Network
Sep 2019
Publication
The Australian Capital Territory (ACT) has legislated and aims to be net zero emissions by 2045. Such ambitious targets have implications for the contribution of hydrogen and its storage in gas distribution networks Therefore we need to understand now the impacts on the gas distribution network of the transition to 100% hydrogen. Assessment of the viability of decarbonising the ACT gas network will be partly based on the cost of reusing the gas network for the safe and reliable distribution of hydrogen. That task requires each element of the natural gas safety management system to be evaluated.
This article describes the construction of a test facility in Canberra Australia used to identify issues raised by 100% hydrogen use in the medium pressure distribution network consisting of nylon and polyethylene (PE) as a means of identifying measures necessary to ensure ongoing validity of the network's regulatory safety case.
Evoenergy (the ACT's gas distribution company) have constructed a Test Facility incorporating an electrolyser a gas supply pressure reduction and mixing skid a replica gas network and a domestic installation with gas appliances. Jointly with Australian National University (ANU) and Canberra Institute of Technology (CIT) the Company has commenced a program of “bench testing” initially with 100% hydrogen to identify gaps in the safety case specifically focusing on the materials work practices and safety systems in the ACT.
The facility is designed to assess:
The paper addresses major safety issues relating to the production/storage distribution and consumer end use of hydrogen injected into existing gas distribution networks. The analysis is guided by the Safety Management System. The Hydrogen Testing Facility described in the paper provide tools for evaluation of hydrogen safety matters in the ACT and Australia-wide.
Testing to date has confirmed that polyethylene and nylon pipe and their respective jointing techniques can contain 100% hydrogen at pressures used for the distribution of natural gas. Testing has also confirmed that current installation work practices on polyethylene and nylon pipe and joints are suitable for hydrogen service. This finding is subject to variation attributable to staff training and skill levels and further testing has been programmed as outlined in this paper.
Testing of gas isolation by clamping and simulated repair on the hydrogen network has established that standard natural gas isolation techniques work with 100% hydrogen at natural gas pressures.
This article describes the construction of a test facility in Canberra Australia used to identify issues raised by 100% hydrogen use in the medium pressure distribution network consisting of nylon and polyethylene (PE) as a means of identifying measures necessary to ensure ongoing validity of the network's regulatory safety case.
Evoenergy (the ACT's gas distribution company) have constructed a Test Facility incorporating an electrolyser a gas supply pressure reduction and mixing skid a replica gas network and a domestic installation with gas appliances. Jointly with Australian National University (ANU) and Canberra Institute of Technology (CIT) the Company has commenced a program of “bench testing” initially with 100% hydrogen to identify gaps in the safety case specifically focusing on the materials work practices and safety systems in the ACT.
The facility is designed to assess:
- Materials in use including aged network materials and components
- Construction and installation techniques both greenfield and live gas work
- Purging and filling techniques
- Leak detection both underground and above ground
- Emergency response and make safe techniques
- Issues associated with use of hydrogen in light commercial and domestic appliances.
- Technicians and gas fitters on infrastructure installation and management
- Emergency response services on responding to hydrogen related emergencies in a network environment; and
- Manage public perceptions of hydrogen in a network environment.
The paper addresses major safety issues relating to the production/storage distribution and consumer end use of hydrogen injected into existing gas distribution networks. The analysis is guided by the Safety Management System. The Hydrogen Testing Facility described in the paper provide tools for evaluation of hydrogen safety matters in the ACT and Australia-wide.
Testing to date has confirmed that polyethylene and nylon pipe and their respective jointing techniques can contain 100% hydrogen at pressures used for the distribution of natural gas. Testing has also confirmed that current installation work practices on polyethylene and nylon pipe and joints are suitable for hydrogen service. This finding is subject to variation attributable to staff training and skill levels and further testing has been programmed as outlined in this paper.
Testing of gas isolation by clamping and simulated repair on the hydrogen network has established that standard natural gas isolation techniques work with 100% hydrogen at natural gas pressures.
The CALIF3S-P2remics Software – An Application to Underexpanded Hydrogen Jet Deflagration
Sep 2019
Publication
To assess explosion hazard the French Institut de Radioprotection et de Sûreté Nucléaire (IRSN) is developing the P2REMICS software (for Partially PREMIxed Combustion Solver) on the basis of the generic CFD solver library CALIF3S (for Components Adaptive Library for Fluid Flow Simulation). Both P2REMICS and CALIF3S are in-house IRSN softwares released under an open-source license. CALIF3S-P2REMICS is dedicated to the simulation of explosion scenarii (explosive atmosphere formation deflagration or detonation and blast waves propagation) for hydrogen as more generally for any explosive gas or gas/dust mixture. It is based on staggered space discretizations and implements fractional-steps time algorithms well suited for massively parallel computations. A wide range of experiments is used for the software validation. Among them we focus here on a free underexpanded hydrogen jet deflagration performed in two steps: first the hydrogen is released in air up to obtain a steady jet (dispersion phase) then the deflagration is triggered. For the dispersion phase simulation a notional nozzle approach is used to get rid of the description of the shocked zone located near the nozzle. Then a so-called turbulent flame velocity approach is chosen for the deflagration simulation. The computations allow to highlight the complex flow structures induced by the inhomogeneity fuel concentration in the jet. A large dispersion of results is observed depending on the chosen correlation for the turbulent flame speed.
Inhomogeneous Hydrogen Deflagrations in the Presence of Obstacles in 25 m3 Enclosure. Experimental Results
Sep 2019
Publication
Explosion venting is a frequently used measure to mitigate the consequence of gas deflagrations in closed environments. Despite the effort to predict the vent area needed to achieved the protection through engineering formulas and CFD tools work has still to be done to reliably predict the outcome of a vented gas explosion. Blind-prediction exercises recently published show a large spread in the prediction of both engineering formula than CFD tools. University of Pisa performed experimental tests in a 25 m3 facility in inhomogeneous conditions and with the presence of simple obstacles constituted by plates bolted to HEB beams. The present paper is aimed to share the results of hydrogen dispersion and deflagration tests and discuss the comparison of maximum peak overpressure generated with different blockage ratio and repeated obstacles sets. Description of the experimental set-up includes all the details deemed necessary to reproduce the phenomenon with a CFD tool.
Laboratory Method for Simulating Hydrogen Assisted Degradation of Gas Pipeline Steels
Aug 2019
Publication
Integrity of natural gas transmission systems is of great importance for energy and environmental security. Deterioration occurs in gas transit pipelines due to operational conditions and action of corrosion and hydrogenating media and leads to changes in microstructure and mechanical properties of pipeline steels which influences on pipeline performance. Hydrogenation of metal during corrosion process together with working stresses facilitates a development of in-bulk damaging at nano- and microscales. Reducing brittle fracture resistance of pipeline steels under operation increases significantly a failure risk of gas pipelines associated with in-bulk material degradation. Therefore hydrogen assisted degradation of pipelines steels under operation calls for effective methods for in-laboratory accelerated degradation. The present study is devoted to the development of the procedure of laboratory simulation of in-service degradation of pipeline steels. The role of hydrogen in degradation of pipeline steels was analysed. The procedure of accelerated degradation of pipeline steels under the combined action of axial loading and hydrogen charging was developed and induced in the laboratory. The procedure was consisted in consistently subjecting of specimens to electrolytic hydrogen charging to an axial loading up and to an artificial aging. Pipeline steels in the different states (as-received post-operated aged and after in-laboratory degradation) were investigated. The tensile mechanical behaviour of steels and impact toughness were experimentally studied. It was definitely concluded that the applied procedure caused the changes in the metal mechanical properties at the same level compared to the properties degradation due to operation. The developed procedure enables on a laboratory scale simulating of pipeline steel degradation during long-term operation under simultaneous action of hydrogenation and working loading and it makes possible to predict the mechanical behaviour of pipeline steels during service.
Investigating the Hydrogen Storage Capacity of Surfactant Modified Graphene
Mar 2019
Publication
As the depletion of traditional fossil fuels and environmental pollution become a serious problem of human society researchers are actively finding renewable green energy sources. Considered as a clean efficient and renewable alternative Hydrogen energy is considered the most promising energy source. However the safe and efficient storage of hydrogen has become the major problem that hinders its application. To solve this gap this paper proposes to utilize surfactant modified graphene for hydrogen storage. With Hummers method and ultrasonic stripping method this study prepared graphene from graphene oxide with NaBH4. Surfactant sodium dodecylbenzene sulfonate (SDBS) was used as a dispersant during the reduction process to produce the dispersion-stabilized graphene suspensions. The characteristics of the graphene suspensions then were examined by XRD SEM TEM FT-IR Raman XPS TG and N2 adsorption-desorption tests. The hydrogen adsorption properties of the samples were investigated with Langmuir and Freundlich fitting. The results show that the adsorption behavior is consistent with the Freundlich adsorption model and the process is a physical adsorption.
Hydrogen Systems Component Safety
Sep 2013
Publication
The deployment of hydrogen technologies particularly the deployment of hydrogen dispensing systems for passenger vehicles requires that hydrogen components perform reliably in environments where they have to meet the following performance parameters:
The paper will use incident frequency data from NREL’s Technology Validation project to more quantitatively identify safety concerns in hydrogen dispensing and storage systems.
- Perform safely where the consumer will be operating the dispensing equipment
- Dispense hydrogen at volumes comparable to gasoline dispensing stations in timeframes comparable to gasoline stations
- Deliver a fueling performance that is within the boundaries of consumer tolerance
- Perform with maintenance/incident frequencies comparable to gasoline dispensing systems
The paper will use incident frequency data from NREL’s Technology Validation project to more quantitatively identify safety concerns in hydrogen dispensing and storage systems.
Numerical Investigation of Detonation in Stratified Combustible Mixture and Oxidizer with Concentration Gradients
Sep 2019
Publication
Hydrogen leakage in a closed space is one of the causes of serious accidents because of its high detonability. Assuming the situation that hydrogen is accumulated in a closed space two-dimensional numerical simulation for hydrogen oxygen detonation which propagates in stratified fuel and oxidizer with concentration gradient is conducted by using detailed chemical reaction model. The concentration gradient between fuel and oxidizer is expressed by changing the number of hydrogen moles by using sigmoid function. Strength of discontinuity at the boundary is controlled by changing the gain of the function. The maximum pressure history shows that the behaviour of triple points is different depending on the strength of discontinuity between the two kind of gas. In without concentration gradient case the transverse waves are reflected at the boundary because of the sudden change of acoustic impedance ratio between two kind of gas. In contrast in with concentration gradient case the transverse wavs are not reflected in the buffer zone and they are flowed into the oxidizer as its structures are kept. As a result the confined effect declines as the strength of discontinuity between the two kind of gas is weakened and the propagating distance of detonation changes
Effects of Steam Injection on the Permissible Hydrogen Content and Gaseous Emissions in a Micro Gas Turbine Supplied by a Mixture of CH4 and H2: A CFD Analysis
Apr 2022
Publication
The use of hydrogen in small scale gas turbines is currently limited by several issues. Blending hydrogen with methane or other gaseous fuels can be considered a low medium-term viable solution with the goal of reducing greenhouse gas emissions. In fact only small amounts can be mixed with methane in premixed combustors due to the risk of flashback. The aim of this article is to investigate the injection of small quantities of steam as a method of increasing the maximum permissible hydrogen content in a mixture with methane. The proposed approach involves introducing the steam directly into the combustion chamber into the main fuel feeding system of a Turbec T100. The study is carried out by means of CFD analysis of the combustion process. A thermodynamic analysis of the energy system is used to determine boundary conditions. The combustion chamber is discretized using a three-dimensional mesh consisting of 4.7 million nodes and the RANS RSM model is used to simulate the effects of turbulence. The results show that the addition of steam may triple the permissible percentage of hydrogen in the mixture for the considered MGT passing from 10% to over 30% by volume also leading to a reduction in NOx emissions without a significant variation in CO emissions.
Hydrogen Deflagrations in Stratified Flat Layers in the Large-scale Vented Combustion Test Facility
Sep 2019
Publication
This paper examines the flame dynamics of vented deflagration in stratified hydrogen layers. It also compares the measured combustion pressure transients with 3D GOTHIC simulations to assess GOTHIC’s capability in simulating the associated phenomena. The experiments were performed in the Large-Scale Vented Combustion Test Facility at the Canadian Nuclear Laboratories. The stratified layer was formed by injecting hydrogen at a high elevation at a constant flow rate. The dominant parameters for vented deflagrations in stratified layers were investigated. The experimental results show that significant overpressures are generated in stratified hydrogen–air mixtures with local high concentration although the volume-averaged hydrogen concentration is non-flammable. The GOTHIC predictions capture the overall pressure dynamics of combustion very well but the peak overpressures are consistently over-predicted particularly with higher maximum hydrogen concentrations. The measured combustion overpressures are also compared with Molkov’s model prediction based on a layer-averaged hydrogen concentration.
Implementation of hydrogen plasma activation of Mg powder in two steps hydrogenation
Oct 2017
Publication
Development of technologically and economically feasible solutions for hydrogen storage stimulates progress in hydrogen economy. High gravimetric and volumetric capacities of magnesium hydride makes it promising material capable to accelerate implementation of hydrogen-based technologies in our daily life. However widely discussed limitations of sorption kinetics and thermodynamic properties must be managed in MgH2. This work investigates two steps hydrogenation when process of hydrogen absorption is followed after hydrogen plasma activation. Such technique initiates creation of new channels for enhanced hydrogen sorption. Moreover synthesis of negligible amount of hydride acts as positive factor for further hydrogenation.
Numerical Investigation of Hydrogen-air Deflagrations in a Repeated Pipe Congestion
Sep 2019
Publication
Emerging hydrogen energy technologies are creating new avenues for bring hydrogen fuel usage into larger public domain. Identification of possible accidental scenarios and measures to mitigate associated hazards should be well understood for establishing best practice guidelines. Accidentally released hydrogen forms flammable mixtures in a very short time. Ignition of such a mixture in congestion and confinements can lead to greater magnitudes of overpressure catastrophic for both structure and people around. Hence understanding of the permissible level of confinements and congestion around the hydrogen fuel handling and storage unit is essential for process safety. In the present study numerical simulations have been performed for the hydrogen-air turbulent deflagration in a well-defined congestion of repeated pipe rig experimentally studied by [1]. Large Eddy Simulations (LES) have been performed using the in-house modified version of the OpenFOAM code. The Flame Surface Wrinkling Model in the LES context is used for modelling deflagrations. Numerical predictions concerning the effects of hydrogen concentration and congestion on turbulent deflagration overpressure are compared with the measurements [1] to provide validation of the code. Further insight about the flame propagation and trends of the generated overpressures over the range of concentrations are discussed.
Localized Plasticity and Associated Cracking in Stable and Metastable High-Entropy Alloys Pre-Charged with Hydrogen
Dec 2018
Publication
We investigated hydrogen embrittlement in Fe20Mn20Ni20Cr20Co and Fe30Mn10Cr10Co (at.%) alloys pre-charged with 100 MPa hydrogen gas by tensile testing at three initial strain rates of 10−4 10−3 and 10−2 s−1 at ambient temperature. The alloys are classified as stable and metastable austenite-based high-entropy alloys (HEAs) respectively. Both HEAs showed the characteristic hydrogen-induced degradation of tensile ductility. Electron backscatter diffraction analysis indicated that the reduction in ductility by hydrogen pre-charging was associated with localized plasticity-assisted intergranular crack initiation. It should be noted as an important finding that hydrogen-assisted cracking of the metastable HEA occurred not through a brittle mechanism but through localized plastic deformation in both the austenite and ε-martensite phases.
A Study on the Influential Factors of Stress Corrosion Cracking in C110 Casing Pipe
Jan 2022
Publication
In this paper we analyze the potential factors affecting the hydrogen sulfide type of stress corrosion cracking in C110 casing pipes. In order to further study these cracking factors the methods of material property testing scanning electron microscopy XRD TEM and 3D ultra-depth-of-field were applied in the experiments. Besides that an HTHP autoclave was independently designed by the laboratory to simulate the actual corrosion environment and the potential factors affecting the stress corrosion cracking of C110 casing pipes were determined. The test results showed that the chemical composition metallographic structure hardness and non-metallic inclusions of the two types of C110 casing pipes were all qualified. In fact there remains a risk of stress corrosion cracking when the two kinds of C110 casing pipes serve under long-term field-working conditions. It is considered in this paper that the precipitates on the material surface stress damage and pitting corrosion are all critical factors affecting the stress corrosion cracking of casing pipes.
Effect of Microstructural and Environmental Variables on Ductility of Austenitic Stainless Steels
Sep 2019
Publication
Austenitic stainless steels are used extensively in harsh environments including for high-pressure gaseous hydrogen service. However the tensile ductility of this class of materials is very sensitive to materials and environmental variables. While tensile ductility is generally insufficient to qualify a material for hydrogen service ductility is an effective tool to explore microstructural and environmental variables and their effects on hydrogen susceptibility to inform understanding of the mechanisms of hydrogen effects in metals and to provide insight to microstructural variables that may improve relative performance. In this study hydrogen precharging was used to simulate high-pressure hydrogen environments to evaluate hydrogen effects on tensile properties. Several austenitic stainless steels were considered including both metastable and stable alloys. Room temperature and subambient temperature tensile properties were evaluated with three different internal hydrogen contents for type 304L and 316L austenitic stainless steels and one hydrogen content for XM-11. Significant ductility loss was observed for both metastable and stable alloys suggesting the stability of the austenitic phase is not sufficient to characterize the effects of hydrogen. Internal hydrogen does influence the character of deformation which drives local damage accumulation and ultimately fracture for both metastable and stable alloys. While a quantitative description of hydrogen-assisted fracture in austenitic stainless steels remains elusive these observations underscore the importance of the hydrogen-defect interactions and the accumulation of damage at deformation length scales.
H2FC SUPERGEN: An Overview of the Hydrogen and Fuel Cell Research Across the UK
Mar 2015
Publication
The United Kingdom has a vast scientific base across the entire Hydrogen and Fuel Cell research landscape with a world class academic community coupled with significant industrial activity from both UK-based Hydrogen and Fuel Cell companies and global companies with a strong presence within the country. The Hydrogen and Fuel Cell (H2FC) SUPERGEN Hub funded by the Engineering and Physical Sciences Research Council (EPSRC) was established in 2012 as a five-year programme to bring the UK's H2FC research community together. Here we present the UK's current Hydrogen and Fuel Cell activities along with the role of the H2FC SUPERGEN Hub.
Hydrogen Effect on Fatigue and Fracture of Pipe Steels
Sep 2009
Publication
Transport by pipe is one the most usual way to carry liquid or gaseous energies from their extraction point until their final field sites. To limit explosion risk or escape to avoid pollution problems and human risks it is necessary to assess nocivity of defect promoting fracture. This need to know the mechanical properties of the pipes steels. Hydrogen is considered to day as a new energy vector and its transport in one of the key problems to extension of its use. Within the European project NATURALHY it has been proposed to transport a mixture of natural gas and hydrogen. 39 European partners have combined their efforts to assess the effects of hydrogen presence on the existing gas network. Key issues are durability of pipeline material integrity management safety aspects life cycle and socio-economic assessment and end-use. The work described in this paper was performed within the NATURALHY work package on ’Durability of pipeline material’. This study makes it possible to emphasize the hydrogen effect on mechanical properties of several pipe steels as X52 X70 or X100 in fatigue and fracture and in two different environments: air and hydrogen electrolytic.
Simulating Vented Hydrogen Deflagrations: Improved Modelling in the CFD Tool Flacs-Hydrogen
Sep 2019
Publication
This paper describes validation of the computational fluid dynamics tool FLACS-Hydrogen. The validation study focuses on concentration and pressure data from vented deflagration experiments performed in 20-foot shipping containers as part of the project Improving hydrogen safety for energy applications through pre-normative research on vented deflagrations (HySEA) funded by the Fuel Cells and Hydrogen 2 Joint Undertaking (FCH 2 JU). The paper presents results for tests involving inhomogeneous hydrogen-air clouds generated from realistic releases performed during the HySEA project. For both experiments and simulations the peak overpressures obtained for the stratified mixtures are higher than those measured for lean homogeneous mixtures with the same amount of hydrogen. Using an in-house version of FLACS-Hydrogen with the numerical solver Flacs3 and improved physics models results in significantly improved predictions of the peak overpressures compared to the predictions by the standard Flacs2 solver. The paper includes suggestions for further improvements to the model system.
No more items...