Spain
Novel Use of Green Hydrogen Fuel Cell-Based Combined Heat and Power Systems to Reduce Primary Energy Intake and Greenhouse Emissions in the Building Sector
Feb 2021
Publication
Achieving European climate neutrality by 2050 requires further efforts not only from the industry and society but also from policymakers. The use of high-efficiency cogeneration facilities will help to reduce both primary energy consumption and CO2 emissions because of the increase in overall efficiency. Fuel cell-based cogeneration technologies are relevant solutions to these points for small- and microscale units. In this research an innovative and new fuel cell-based cogeneration plant is studied and its performance is compared with other cogeneration technologies to evaluate the potential reduction degree in energy consumption and CO2 emissions. Four energy consumption profile datasets have been generated from real consumption data of different dwellings located in the Mediterranean coast of Spain to perform numerical simulations in different energy scenarios according to the fuel used in the cogeneration. Results show that the fuel cell-based cogeneration systems reduce primary energy consumption and CO2 emissions in buildings to a degree that depends on the heat-to-power ratio of the consumer. Primary energy consumption varies from 40% to 90% of the original primary energy consumption when hydrogen is produced from natural gas reforming process and from 5% to 40% of the original primary energy consumption if the cogeneration is fueled with hydrogen obtained from renewable energy sources. Similar reduction degrees are achieved in CO2 emissions.
AMHYCO Project - Towards Advanced Accident Guidelines for Hydrogen Safety in Nuclear Power Plants
Sep 2021
Publication
Severe accidents in nuclear power plants are potentially dangerous to both humans and the environment. To prevent and/or mitigate the consequences of these accidents it is paramount to have adequate accident management measures in place. During a severe accident combustible gases — especially hydrogen and carbon monoxide — can be released in significant amounts leading to a potential explosion risk in the nuclear containment building. These gases need to be managed to avoid threatening the containment integrity which can result in the releases of radioactive material into the environment. The main objective of the AMHYCO project is to propose innovative enhancements in the way combustible gases are managed in case of a severe accident in currently operating reactors. For this purpose the AMHYCO project pursues three specific activities including experimental investigations of relevant phenomena related to hydrogen / carbon monoxide combustion and mitigation with PARs (Passive Autocatalytic Recombiners) improvement of the predictive capabilities of analysis tools used for explosion hazard evaluation inside the reactor containment as well as enhancement of the Severe Accident Management Guidelines (SAMGs) with respect to combustible gases risk management based on theoretical and experimental results. Officially launched on 1 October 2020 AMHYCO is an EU-funded Horizon 2020 project that will last 4 years from 2020 to 2024. This international project consists of 12 organizations (six from European countries and one from Canada) and is led by the Universidad Politécnica de Madrid (UPM). AMHYCO will benefit from the worldwide experts in combustion science accident management and nuclear safety in its Advisory Board. The paper will give an overview of the work program and planned outcome of the project.
Hydrogen as an Energy Vector to Optimize the Energy Exploitation of a Self-consumption Solar Photovoltaic Facility in a Dwelling House
Nov 2019
Publication
Solar photovoltaic (PV) plants coupled with storage for domestic self-consumption purposes seem to be a promising technology in the next years as PV costs have decreased significantly and national regulations in many countries promote their installation in order to relax the energy requirements of power distribution grids. However electrochemical storage systems are still unaffordable for many domestic users and thus the advantages of self-consumption PV systems are reduced. Thus in this work the adoption of hydrogen systems as energy vectors between a PV plant and the energy user is proposed. As a preliminary study in this work the design of a PV and hydrogen-production self-consumption plant for a single dwelling is described. Then a technical and economic feasibility study conducted by modeling the facility within the Homer Energy Pro energy systems analysis tool is reported. The proposed system will be able to provide back not only electrical energy but also thermal energy through a fuel cell or refined water covering the fundamental needs of the householders (electricity heat or cooling and water). Results show that although the proposed system effectively increases the energy local use of the PV production and reduces significantly the energy injections or demands into/from the power grid avoiding power grid congestions and increasing the nano-grid resilience operation and maintenance costs may reduce its economic attractiveness for a single dwelling.
The Role of Hydrogen in Heavy Transport to Operate within Planetary Boundaries
Jul 2021
Publication
Green hydrogen i.e. produced from renewable resources is attracting attention as an alternative fuel for the future of heavy road transport and long-distance driving. However the benefits linked to zero pollution at the usage stage can be overturned when considering the upstream processes linked to the raw materials and energy requirements. To better understand the global environmental implications of fuelling heavy transport with hydrogen we quantified the environmental impacts over the full life cycle of hydrogen use in the context of the Planetary Boundaries (PBs). The scenarios assessed cover hydrogen from biomass gasification (with and without carbon capture and storage [CCS]) and electrolysis powered by wind solar bioenergy with CCS nuclear and grid electricity. Our results show that the current diesel-based-heavy transport sector is unsustainable due to the transgression of the climate change-related PBs (exceeding standalone by two times the global climate-change budget). Hydrogen-fuelled heavy transport would reduce the global pressure on the climate change-related PBs helping the transport sector to stay within the safe operating space (i.e. below one-third of the global ecological budget in all the scenarios analysed). However the best scenarios in terms of climate change which are biomass-based would shift burdens to the biosphere integrity and nitrogen flow PBs. In contrast burden shifting in the electrolytic scenarios would be negligible with hydrogen from wind electricity emerging as an appealing technology despite attaining higher carbon emissions than the biomass routes
Assessing the Prospective Environmental Performance of Hydrogen from High Temperature Electrolysis Coupled with Concentrated Solar Power
Jul 2022
Publication
Hydrogen is currently being promoted because of its advantages as an energy vector its potential 12 to decarbonise the economy and strategical implications in terms of energy security. Hydrogen 13 from high-temperature electrolysis coupled with concentrated solar power (CSP) is especially 14 interesting since it enhances the last two aspects and could benefit from significant technological 15 progress in the coming years. However there is a lack of studies assessing its future 16 environmental performance. This work fills this gap by carrying out a prospective life cycle 17 assessment based on the expected values of key performance parameters in 2030. The results 18 show that parabolic trough CSP coupled with a solid oxide electrolyser is a promising solution 19 under environmental aspects. It leads to a prospective hydrogen carbon footprint (1.85 kg CO2 20 eq/kg H2) which could be classified as low-carbon according to current standards. The 21 benchmarking study for the year 2030 shows that the assessed system significantly decreases the 22 hydrogen carbon footprint compared to future hydrogen from steam methane reforming (81% 23 reduction) and grid electrolysis (51%) even under a considerable penetration of renewable energy 24 sources.
Techno-economic Modelling of Water Electrolysers in the Range of Several MW to Provide Grid Services While Generating Hydrogen for Different Applications: A Case Study in Spain Applied to Mobility with FCEVs
Jun 2019
Publication
The use of hydrogen as energy carrier is a promising option to decarbonize both energy and transport sectors. This paper presents an advanced techno-economic model for calculation of optimal dispatch of large-scale multi MW electrolysis plants in order to obtain a more accurate evaluation of the feasibility of business cases related to the supply of this fuel for different end uses combined with grid services' provision. The model is applied to the Spanish case using different scenarios to determine the minimum demand required from the FCEV market so that electrolysis facilities featuring several MW result in profitable business cases. The results show that grid services contribute to the profitability of hydrogen production for mobility given a minimum but considerable demand from FCEV fleets.
Alkaline Electrolysis for Hydrogen Production at Sea: Perspectives on Economic Performance
May 2023
Publication
Alkaline electrolysis is already a proven technology on land with a high maturity level and good economic performance. However at sea little is known about its economic performance toward hydrogen production. Alkaline electrolysis units operate with purified water to split its molecules into hydrogen and oxygen. Purified water and especially that sourced from the sea has a variable cost that ultimately depends on its quality. However the impurities present in that purified water have a deleterious effect on the electrolyte of alkaline electrolysis units that cause them to drop their energy efficiency. This in turn implies a source of economic losses resulting from the cost of electricity. In addition at sea there are various options regarding the electrolyte management of which the cost depends on various factors. All these factors ultimately impact on the levelized cost of the produced hydrogen. This article aims to shed some light on the economic performance of alkaline electrolysis units operating under sea conditions highlighting the knowledge gaps in the literature and initiating a debate in the field.
Optimal Dispatch Model for PV-electrolysis Plants in Self-consumption Regime to Produce Green Hydrogen: A Spanish Case Study
May 2022
Publication
The production of green hydrogen from renewable energy by means of water electrolysis is a promising approach to support energy sector decarbonization. This paper presents a techno-economic model of plants with PV sources connected to electrolysis in self-consumption regime that considers the dynamics of electrolysis systems. The model calculates the optimal hourly dispatch of the electrolysis system including the operational states (production standby and idle) the load factor in production and the energy imports and exports to the electricity grid. Results indicate that the model is a useful decision support tool to operate electrolysis plants connected to PV plants in self-consumption regimes with the target of reducing hydrogen production costs.
Assessing the Feasibility of Hydrogen and Electric Buses for Urban Public Transportation using Rooftop Integrated Photovoltaic Energy in Cuenca Ecuador
Jul 2023
Publication
A main restriction of renewables from intermittent sources is the mismatch between energy resource availability and energy requirements especially when extensive power plants are producing at their highest potential causing huge energy surpluses. In these cases excess power must be stored or curtailed. One alternative is increasing urban solar potential which could be integrated to feed electric buses directly or alternatively through hydrogen (H2 ) as an energy vector. H2 from renewable electricity can be stored and used directly or through fuel cells. This study aims to determine the H2 capability that could be achieved when integrating large-scale photovoltaic (PV) generation in urban areas. This analysis was carried out by determining the PV energy potentially generated by installing PV in Cuenca City downtown (Ecuador). Cuenca is in the process of adopting renewal of the public transport vehicle fleet introducing a new model with an electric tram main network combined with “clean type buses”. The conventional diesel urban transport could be replaced establishing a required vehicle fleet of 475 buses spread over 29 routes emitting 112 tons of CO2 and burning 11175 gallons of diesel daily. Between the main findings we concluded that the electricity that could be produced in the total roof area exceeds the actual demand in the study area by 5.5 times. Taking into account the energy surplus it was determined that the available PV power will cover from 97% to 127% of the total demand necessary to mobilize the city bus fleet. The novelty of this work is the proposal of a combined methodology to find the potential to feed urban transport with urban solar power in cities close to the equatorial line.
Risk Management of Energy Communities with Hydrogen Production and Storage Technologies
Jul 2023
Publication
The distributed integration of renewable energy sources plays a central role in the decarbonization of economies. In this regard energy communities arise as a promising entity to coordinate groups of proactive consumers (prosumers) and incentivize investment on clean technologies. However the uncertain nature of renewable energy generation residential loads and trading tariffs pose important challenges both at the operational and economic levels. We study how this management can be directly undertaken by an arbitrageur that making use of an adequate price-based demand response (real-time pricing) system serves as an intermediary with the central electricity market to coordinate different types of prosumers under risk aversion. In particular we consider a sequential futures and spot market where the aggregated shortage or excess of energy within the community can be traded. We aim to study the impact of new hydrogen production and storage technologies on community operation and risk management. These interactions are modeled as a game theoretical setting in the form of a stochastic two-stage bilevel optimization problem which is later reformulated without approximation as a single-level mixed-integer linear problem (MILP). An extensive set of numerical experiments based on real data is performed to study the operation of the energy community under different technical and economical conditions. Results indicate that the optimal involvement in futures and spot markets is highly conditioned by the community’s risk aversion and self-sufficiency levels. Moreover the external hydrogen market has a direct effect on the community’s internal price-tariff system and depending on the market conditions may worsen the utility of individual prosumers.
Water Electrolysis for the Production of Hydrogen to Be Employed in the Ironmaking and Steelmaking Industry
Nov 2021
Publication
The way to decarbonization will be characterized by the huge production of hydrogen through sustainable routes. Thus the basic production way is water electrolysis sustained by renewable energy sources allowing for obtaining “green hydrogen”. The present paper reviews the main available technologies for the water electrolysis finalized to the hydrogen production. We describe the fundamental of water electrolysis and the problems related to purification and/or desalinization of water before electrolysis. As a matter of fact we describe the energy efficiency issues with particular attention to the potential application in the steel industry. The fundamental aspects related to the choice of high-temperature or low-temperature technologies are analyzed.
Use of Hydrogen in Off-Grid Locations, a Techno-Economic Assessment
Nov 2018
Publication
Diesel generators are currently used as an off-grid solution for backup power but this causes CO2 and GHG emissions noise emissions and the negative effects of the volatile diesel market influencing operating costs. Green hydrogen production by means of water electrolysis has been proposed as a feasible solution to fill the gaps between demand and production the main handicaps of using exclusively renewable energy in isolated applications. This manuscript presents a business case of an off-grid hydrogen production by electrolysis applied to the electrification of isolated sites. This study is part of the European Ely4off project (n◦ 700359). Under certain techno-economic hypothesis four different system configurations supplied exclusively by photovoltaic are compared to find the optimal Levelized Cost of Electricity (LCoE): photovoltaic-batteries photovoltaic-hydrogen-batteries photovoltaic-diesel generator and diesel generator; the influence of the location and the impact of different consumptions profiles is explored. Several simulations developed through specific modeling software are carried out and discussed. The main finding is that diesel-based systems still allow lower costs than any other solution although hydrogen-based solutions can compete with other technologies under certain conditions.
Challenges and Prospects of Renewable Hydrogen-based Strategies for Full Decarbonization of Stationary Power Applications
Oct 2021
Publication
The exponentially growing contribution of renewable energy sources in the electricity mix requires large systems for energy storage to tackle resources intermittency. In this context the technologies for hydrogen production offer a clean and versatile alternative to boost renewables penetration and energy security. Hydrogen production as a strategy for the decarbonization of the energy sources mix has been investigated since the beginning of the 1990s. The stationary sector i.e. all parts of the economy excluding the transportation sector accounts for almost three-quarters of greenhouse gases (GHG) emissions (mass of CO2-eq) in the world associated with power generation. While several publications focus on the hybridization of renewables with traditional energy storage systems or in different pathways of hydrogen use (mainly power-to-gas) this study provides an insightful analysis of the state of art and evolution of renewable hydrogen-based systems (RHS) to power the stationary sector. The analysis started with a thorough review of RHS deployments for power-to-power stationary applications such as in power generation industry residence commercial building and critical infrastructure. Then a detailed evaluation of relevant techno-economic parameters such as levelized cost of energy (LCOE) hydrogen roundtrip efficiency (HRE) loss of power supply probability (LPSP) self-sufficiency ratio (SSR) or renewable fraction (fRES) is provided. Subsequently lab-scale plants and pilot projects together with current market trends and commercial uptake of RHS and fuel cell systems are examined. Finally the future techno-economic barriers and challenges for short and medium-term deployment of RHS are identified and discussed.
Recent Progress and New Perspectives on Metal Amide and Imide Systems for Solid-State Hydrogen Storage
Apr 2018
Publication
Hydrogen storage in the solid state represents one of the most attractive and challenging ways to supply hydrogen to a proton exchange membrane (PEM) fuel cell. Although in the last 15 years a large variety of material systems have been identified as possible candidates for storing hydrogen further efforts have to be made in the development of systems which meet the strict targets of the Fuel Cells and Hydrogen Joint Undertaking (FCH JU) and U.S. Department of Energy (DOE). Recent projections indicate that a system possessing: (i) an ideal enthalpy in the range of 20–50 kJ/mol H2 to use the heat produced by PEM fuel cell for providing the energy necessary for desorption; (ii) a gravimetric hydrogen density of 5 wt. % H2 and (iii) fast sorption kinetics below 110 ◦C is strongly recommended. Among the known hydrogen storage materials amide and imide-based mixtures represent the most promising class of compounds for on-board applications; however some barriers still have to be overcome before considering this class of material mature for real applications. In this review the most relevant progresses made in the recent years as well as the kinetic and thermodynamic properties experimentally measured for the most promising systems are reported and properly discussed.
Finding Synergy Between Renewables and Coal: Flexible Power and Hydrogen Production from Advanced IGCC Plants with Integrated CO2 Capture
Feb 2021
Publication
Variable renewable energy (VRE) has seen rapid growth in recent years. However VRE deployment requires a fleet of dispatchable power plants to supply electricity during periods with limited wind and sunlight. These plants will operate at reduced utilization rates that pose serious economic challenges. To address this challenge this paper presents the techno-economic assessment of flexible power and hydrogen production from integrated gasification combined cycles (IGCC) employing the gas switching combustion (GSC) technology for CO2 capture and membrane assisted water gas shift (MAWGS) reactors for hydrogen production. Three GSC-MAWGS-IGCC plants are evaluated based on different gasification technologies: Shell High Temperature Winkler and GE. These advanced plants are compared to two benchmark IGCC plants one without and one with CO2 capture. All plants utilize state-of-the-art H-class gas turbines and hot gas clean-up for maximum efficiency. Under baseload operation the GSC plants returned CO2 avoidance costs in the range of 24.9–36.9 €/ton compared to 44.3 €/ton for the benchmark. However the major advantage of these plants is evident in the more realistic mid-load scenario. Due to the ability to keep operating and sell hydrogen to the market during times of abundant wind and sun the best GSC plants offer a 6–11%-point higher annual rate of return than the benchmark plant with CO2 capture. This large economic advantage shows that the flexible GSC plants are a promising option for balancing VRE provided a market for the generated clean hydrogen exists.
Preliminary Design of a Self-Sufficient Electrical Storage System Based on Electrolytic Hydrogen for Power Supply in a Residential Application
Oct 2021
Publication
The use of renewable energy and hydrogen technology is a sustainable solution for the intermittent feature of renewable energies. Hence the aim of the present work is to design a self-sufficient system for a one-family house by coupling a solar photovoltaic array and an anion exchange membrane water electrolyzer (AEMWE). The first step is the selection of the photovoltaic panel by using PV-SYST 7.0 software. Then the hydrogen production system is calculated by coupling the electrolyzer and photovoltaic panel current–potential curves. A fuel cell is selected to use the hydrogen produced when solar energy is not available. Finally the hydrogen storage tank is also estimated to store hydrogen for a design basis of four consecutive cloudy days according to the hydrogen consumption of the fuel cell. The whole system is designed by a simple procedure for a specific location in Ciudad Real (Spain) for January which is known as the coldest month of the year. The simple procedure described in this work could be used elsewhere and demonstrated that the hydrogen production at low scale is a suitable technology to use renewable energy for self-energy supporting in a residential application without any connection to the grid.
Prospective Techno-economic and Environmental Assessment of a National Hydrogen Production Mix for Road Transport
Nov 2019
Publication
Fuel cell electric vehicles arise as an alternative to conventional vehicles in the road transport sector. They could contribute to decarbonising the transport system because they have no direct CO2 emissions during the use phase. In fact the life-cycle environmental performance of hydrogen as a transportation fuel focuses on its production. In this sense through the case study of Spain this article prospectively assesses the techno-economic and environmental performance of a national hydrogen production mix by following a methodological framework based on energy systems modelling enriched with endogenous carbon footprint indicators. Taking into account the need for a hydrogen economy based on clean options alternative scenarios characterised by carbon footprint restrictions with respect to a fossil-based scenario dominated by steam methane reforming are evaluated. In these scenarios the steam reforming of natural gas still arises as the key hydrogen production technology in the short term whereas water electrolysis is the main technology in the medium and long term. Furthermore in scenarios with very restrictive carbon footprint limits biomass gasification also appears as a key hydrogen production technology in the long term. In the alternative scenarios assessed the functional substitution of hydrogen for conventional fossil fuels in the road transport sector could lead to high greenhouse gas emission savings ranging from 36 to 58 Mt CO2 eq in 2050. Overall these findings and the model structure and characterisation developed for the assessment of hydrogen energy scenarios are expected to be relevant not only to the specific case study of Spain but also to analysts and decision-makers in a large number of countries facing similar concerns.
Green Hydrogen Storage in an Underground Cavern: A Case Study in Salt Diapir of Spain
Jun 2022
Publication
The Poza de la Sal diapir is a closed circular depression with Cretaceous Mesozoic materials formed by gypsum Keuper clays and a large extension of salt in the center with intercalations of ophite. The low seismic activity of the area the reduced permeability and porosity of the salt caverns and the proximity to the Páramo de Poza wind park make it a suitable place for the construction of a facility for underground storage of green hydrogen obtained from surplus wind power. The design of a cavern for hydrogen storage at a depth of 1000 m takes into account the differences in stresses temperatures and confining pressures involved in the salt deformation process. During the 8 months of the injection phase 23.0 GWh can be stored in the form of hydrogen obtained from the wind energy surplus to be used later in the extraction phase. The injection and extraction ratio must be developed under the conditions of geomechanical safety of the cavity so as to minimize the risks to the environment and people by conditioning the gas pressure inside the cavity to remain within a given range.
Life Cycle Environmental and Cost Comparison of Current and Future Passenger Cars under Different Energy Scenarios
Apr 2020
Publication
In this analysis life cycle environmental burdens and total costs of ownership (TCO) of current (2017) and future (2040) passenger cars with different powertrain configurations are compared. For all vehicle configurations probability distributions are defined for all performance parameters. Using these a Monte Carlo based global sensitivity analysis is performed to determine the input parameters that contribute most to overall variability of results. To capture the systematic effects of the energy transition future electricity scenarios are deeply integrated into the ecoinvent life cycle assessment background database. With this integration not only the way how future electric vehicles are charged is captured but also how future vehicles and batteries are produced. If electricity has a life cycle carbon content similar to or better than a modern natural gas combined cycle powerplant full powertrain electrification makes sense from a climate point of view and in many cases also provides reductions in TCO. In general vehicles with smaller batteries and longer lifetime distances have the best cost and climate performance. If a very large driving range is required or clean electricity is not available hybrid powertrain and compressed natural gas vehicles are good options in terms of both costs and climate change impacts. Alternative powertrains containing large batteries or fuel cells are the most sensitive to changes in the future electricity system as their life cycles are more electricity intensive. The benefits of these alternative drivetrains are strongly linked to the success of the energy transition: the more the electricity sector is decarbonized the greater the benefit of electrifying passenger vehicles.
Transportation in a 100% Renewable Energy System
Jan 2018
Publication
A 100% renewable economy would give a lasting solution to the challenges raised by climate change energy security sustainability and pollution. The conversion of the present transport system appears to be one of the most difficult aspects of such renewable transition. This study reviews the technologies and systems that are being proposed or proven as alternative to fossil-fuel based transportation and their prospects for their entry into the post-carbon era from both technological and energetic viewpoints. The energetic cost of the transition from the current transportation system into global 100% renewable transportation is estimated as well as the electrical energy required for the operation of the new renewable transportation sector. A 100% renewable transport providing the same service as global transport in 2014 would demand about 18% less energy. The main reduction is expected in road transport (69%) but the shipping and air sectors would notably increase their consumptions: 163% and 149% respectively. The analysis concludes that a 100% renewable transportation is feasible but not necessarily compatible with indefinite increase of resources consumption. The major material and energy limitations and obstacles of each transport sector for this transition are shown.
Resilience-oriented Schedule of Microgrids with Hybrid Energy Storage System using Model Predictive Control
Nov 2021
Publication
Microgrids can be regarded as a promising solution by which to increase the resilience of power systems in an energy paradigm based on renewable generation. Their main advantage is their ability to work as islanded systems under power grid outage conditions. Microgrids are usually integrated into electrical markets whose schedules are carried out according to economic aspects while resilience criteria are ignored. This paper shows the development of a resilience-oriented optimization for microgrids with hybrid Energy Storage System (ESS) which is validated via numerical simulations. A hybrid ESS composed of hydrogen and batteries is therefore considered with the objective of improving the autonomy of the microgrid while achieving a rapid transition response. The control problem is formulated using Stochastic Model Predictive Control (SMPC) techniques in order to take into account possible transitions between grid-connected and islanded modes at all the sample instants of the schedule horizon (SH). The control problem is developed by considering a healthy operation of the hybrid ESS thus avoiding degradation issues. The plant is modeled using the Mixed Logic Dynamic (MLD) framework owing to the presence of logic and dynamic control variables.
The Effect of Heat Treatments on the Constituent Materials of a Nuclear Reactor Pressure Vessel in Hydrogen Environment
Jul 2016
Publication
A nuclear reactor pressure vessel (NRPV) wall is formed by two layer of different materials: an inner layer of stainless steel (cladding material) and an outer layer of low carbon steel (base material) which is highly susceptible to corrosion related phenomena. A reduction of the mechanical properties of both materials forming the wall would appear due to the action of the harsh environment causing hydrogen embrittlement (HE) related phenomena. As a result of the manufacturing process residual stresses and strains appear in the NRPV wall thereby influencing the main stage in HE: hydrogen diffusion. A common engineering practice for reducing such states is to apply a tempering heat treatment. In this paper a numerical analysis is carried out for revealing the influence of the heat treatment parameters (tempering temperature and tempering time) on the HE of a commonly used NRPV. To achieve this goal a numerical model of hydrogen diffusion assisted by stress and strain was used considering diverse residual stress-strain states after tempering. This way the obtained hydrogen accumulation during operation time of the NRPV provides insight into the better tempering conditions from the structural integrity point of view.
Fuzzy Logic-based Energy Management System for Grid-connected Residential DC Microgrids with Multi-stack Fuel Cell Systems: A Multi-objective Approach
Aug 2022
Publication
Hybrid energy storage systems (HESS) are considered for use in renewable residential DC microgrids. This architecture is shown as a technically feasible solution to deal with the stochasticity of renewable energy sources however the complexity of its design and management increases inexorably. To address this problem this paper proposes a fuzzy logic-based energy management system (EMS) for use in grid-connected residential DC microgrids with HESS. It is a hydrogen-based HESS composed of batteries and multi-stack fuel cell system. The proposed EMS is based on a multivariable and multistage fuzzy logic controller specially designed to cope with a multi-objective problem whose solution increases the microgrid performance in terms of efficiency operating costs and lifespan of the HESS. The proposed EMS considers the power balance in the microgrid and its prediction the performance and degradation of its subsystems as well as the main electricity grid costs. This article assesses the performance of the developed EMS with respect to three reference EMSs present in the literature: the widely used dual-band hysteresis and two based on multi-objective model predictive control. Simulation results show an increase in the performance of the microgrid from a technical and economic point of view.
True Cost of Solar Hydrogen
Sep 2021
Publication
Green hydrogen will be an essential part of the future 100% sustainable energy and industry system. Up to one-third of the required solar and wind electricity would eventually be used for water electrolysis to produce hydrogen increasing the cumulative electrolyzer capacity to about 17 TWel by 2050. The key method applied in this research is a learning curve approach for the key technologies i.e. solar photovoltaics (PV) and water electrolyzers and levelized cost of hydrogen (LCOH). Sensitivities for the hydrogen demand and various input parameters are considered. Electrolyzer capital expenditure (CAPEX) for a large utility-scale system is expected to decrease from the current 400 €/kWel to 240 €/kWel by 2030 and to 80 €/kWel by 2050. With the continuing solar PV cost decrease this will lead to an LCOH decrease from the current 31–81 €/ MWhH2LHV (1.0–2.7 €/kgH2) to 20–54 €/MWhH2LHV (0.7–1.8 €/kgH2) by 2030 and 10–27 €/MWhH2LHV (0.3–0.9 €/kgH2) by 2050 depending on the location. The share of PV electricity cost in the LCOH will increase from the current 63% to 74% by 2050.
Value of Green Hydrogen When Curtailed to Provide Grid Balancing Services
Aug 2022
Publication
This paper evaluates the potential of grid services in France Italy Norway and Spain to provide an alternative income for electrolysers producing hydrogen from wind power. Grid services are simulated with each country's data for 2017 for energy prices grid services and wind power profiles from relevant wind parks. A novel metric is presented the value of curtailed hydrogen which is independent from several highly uncertain parameters such as electrolyser cost or hydrogen market price. Results indicate that grid services can monetise the unused spare capacity of electrolyser plants improving their economy in the critical deployment phase. For most countries up-regulation yields a value of curtailed hydrogen above 6 V/kg over 3 times higher than the EU's 2030 price target (without incentives). However countries with large hydro power resources such as Norway yield far lower results below 2 V/kg. The value of curtailed hydrogen also decreases with hydrogen production corresponding to the cases of symmetric and down-regulation.
Green Energy by Hydrogen Production from Water Splitting, Water Oxidation Catalysis and Acceptorless Dehydrogenative Coupling
Feb 2023
Publication
In this review we want to explain how the burning of fossil fuels is pushing us towards green energy. Actually for a long time we have believed that everything is profitable that resources are unlimited and there are no consequences. However the reality is often disappointing. The use of non-renewable resources the excessive waste production and the abandonment of the task of recycling has created a fragile thread that once broken may never restore itself. Metaphors aside we are talking about our planet the Earth and its unique ability to host life including ourselves. Our world has its balance; when the wind erodes a mountain a beach appears or when a fire devastates an area eventually new life emerges from the ashes. However humans have been distorting this balance for decades. Our evolving way of living has increased the number of resources that each person consumes whether food shelter or energy; we have overworked everything to exhaustion. Scientists worldwide have already said actively and passively that we are facing one of the biggest problems ever: climate change. This is unsustainable and we must try to revert it or if we are too late slow it down as much as possible. To make this happen there are many possible methods. In this review we investigate catalysts for using water as an energy source or instead of water alcohols. On the other hand the recycling of gases such as CO2 and N2O is also addressed but we also observe non-catalytic means of generating energy through solar cell production.
Hydrogen Production from Surplus Electricity Generated by an Autonomous Renewable System: Scenario 2040 on Grand Canary Island, Spain
Sep 2022
Publication
The electrification of final energy uses is a key strategy to reach the desired scenario with zero greenhouse gas emissions. Many of them can be electrified with more or less difficulty but there is a part that is difficult to electrify at a competitive cost: heavy road transport maritime and air transport and some industrial processes are some examples. For this reason the possibility of using other energy vectors rather than electricity should be explored. Hydrogen can be considered a real alternative especially considering that this transition should not be carried out immediately because initially the electrification would be carried out in those energy uses that are considered most feasible for this conversion. The Canary Islands’ government is making considerable efforts to promote a carbon-free energy mix starting with renewable energy for electricity generation. Still in the early–mid 2030s it will be necessary to substitute heavy transport fossil fuel. For this purpose HOMER software was used to analyze the feasibility of hydrogen production using surplus electricity produced by the future electricity system. The results of previous research on the optimal generation MIX for Grand Canary Island based exclusively on renewable sources were used. This previous research considers three possible scenarios where electricity surplus is in the range of 2.3–4.9 TWh/year. Several optimized scenarios using demand-side management techniques were also studied. Therefore based on the electricity surpluses of these scenarios the optimization of hydrogen production and storage systems was carried out always covering at least the final hydrogen demand of the island. As a result it is concluded that it would be possible to produce 3.5 × 104 to 7.68 × 104 t of H2/year. In these scenarios 3.15 × 105 to 6.91 × 105 t of water per year would be required and there could be a potential production of 2.8 × 105 to 6.14 × 105 t of O2 per year.
Recent Progress in Catalysts for Hydrogen-Chlorine Regenerative Fuel Cells
Oct 2020
Publication
The increasing energy demand and the subsequent climate change consequences are supporting the search for sustainable alternatives to fossil fuels. In this scenario the link between hydrogen and renewable energy is playing a key role and unitized hydrogen-chlorine (H2-Cl2) regenerative cells (RFCs) have become promising candidates for renewable energy storage. Described herein are the recent advances in cell configurations and catalysts for the different reactions that may take place in these systems that work in both modes: electrolysis and fuel cell. It has been found that platinum (Pt)-based catalysts are the best choice for the electrode where hydrogen is involved whereas for the case of chlorine ruthenium (Ru)-based catalysts are the best candidates. Only a few studies were found where the catalysts had been tested in both modes and recent advances are focused on decreasing the amount of precious metals contained in the catalysts. Moreover the durability of the catalysts tested under realistic conditions has not been thoroughly assessed becoming a key and mandatory step to evaluate the commercial viability of the H2-Cl2 RFC technology.
Global Gas Report 2022
May 2022
Publication
This edition of the Global Gas Report covers two very turbulent years in the global gas industry and the wider global energy markets. The Covid-19 pandemic lockdowns with a brief period of excess supply and low prices gave way to tight energy markets extreme price volatility and a compounding geopolitical challenge to energy security. At the time of writing the ongoing Russia-Ukraine conflict has been affecting the flows of gas and has put Europe on a quest to diversify its energy and gas supply that is now opening a new paradigm in the energy industry. This report comes at a time when the situation for global commodity and gas markets is in a state of rapid change and the strategic path forwards for the gas industry and energy policy-makers is continually developing. One thing is clear this is a critical and decisive moment for the gas industry. How it navigates the way through this crisis and charts a path forward will shape its long-term success and the role that it will play in the energy transition and beyond. This is the moment for the gas industry to demonstrate that gas can deliver a sustainable and secure energy future for all and that natural gas and a portfolio of decarbonized low- and zero-carbon gases are key to an achievable energy transition. This year’s report assesses key gas market trends from 2020 and 2021 including Covid-19 outcomes tightness of supply price volatility investments and the upward reversal in the global emissions trend. It then turns to the main topic on the global energy agenda – security – and considers key variables impacting it from industry and policy perspectives as well as considering possible paths to reinforce it. Finally the report looks at the main decarbonization pathways for gas supply as they progressively develop to make gas itself a low or zero-carbon fuel for the future. This report seeks to deliver insights about the global gas sector and to inform its stakeholders partners and importantly global decision-makers about the state of play today and possibilities for the future. It concludes with key insights on how sustainability security and competitiveness can help to deliver a sustainable future in line with the goals of the Paris Agreement and the UN Sustainable Development Agenda.
Life Cycle Assessment of Improved High Pressure Alkaline Electrolysis
Aug 2015
Publication
This paper investigates environmental impacts of high pressure alkaline water electrolysis systems. An advanced system with membranes on polymer basis is compared to a state-of-the-art system with asbestos membranes using a Life Cycle Assessment (LCA) approach. For the advanced system a new improved membrane technology has been investigated within the EU research project “ELYGRID”. Results indicate that most environmental impacts are caused by the electricity supply necessary for operation. During the construction phase cell stacks are the main contributor to environmental impacts. New improved membranes have relatively small contributions to impacts caused by cell construction within the advanced systems. As main outcome the systems comparison illustrates a better ecological performance of the new developed system
Hydrogen-assisted Fatigue Crack Growth: Pre-charging vs In-situ Testing in Gaseous Environments
Mar 2023
Publication
We investigate the implications of conducting hydrogen-assisted fatigue crack growth experiments in a hydrogen gas environment (in-situ hydrogen charging) or in air (following exposure to hydrogen gas). The study is conducted on welded 42CrMo4 steel a primary candidate for the future hydrogen transport infrastructure allowing us to additionally gain insight into the differences in behavior between the base steel and the coarse grain heat affected zone. The results reveal significant differences between the two testing approaches and the two weld regions. The differences are particularly remarkable for the comparison of testing methodologies with fatigue crack growth rates being more than one order of magnitude higher over relevant loading regimes when the samples are tested in a hydrogen-containing environment relative to the pre-charged samples. Aided by finite element modelling and microscopy analysis these differences are discussed and rationalized. Independent of the testing approach the heat affected zone showed a higher susceptibility to hydrogen embrittlement. Similar microstructural behavior is observed for both testing approaches with the base metal exhibiting martensite lath decohesion while the heat affected zone experienced both martensite lath decohesion and intergranular fracture.
Integration of a Multi-Stack Fuel Cell System in Microgrids: A Solution Based on Model Predictive Control
Sep 2020
Publication
This paper proposes a multi-objective model predictive control (MPC) designed for the power management of a multi-stack fuel cell (FC) system integrated into a renewable sources-based microgrid. The main advantage of MPC is the fact that it allows the current timeslot to be optimized while taking future timeslots into account. The multi-objective function solves the problem related to the power dispatch at time that includes criteria to reduce the multi-stack FC degradation operating and maintenance costs as well as hydrogen consumption. Regarding the scientific literature the novelty of this paper lies in the proposal of a generalized MPC controller for a multi-stack FC that can be used independently of the number of stacks that make it up. Although all the stacks that make up the modular FC system are identical their levels of degradation in general will not be. Thus over time each stack can present a different behavior. Therefore the power control strategy cannot be based on an equal distribution according to the nominal power of each stack. On the contrary the control algorithm should take advantage of the characteristics of the multi-stack FC concept distributing operation across all the stacks regarding their capacity to produce power/energy and optimizing the overall performance.
Comparative Analysis of Energy and Exergy Performance of Hydrogen Production Methods
Nov 2020
Publication
The study of the viability of hydrogen production as a sustainable energy source is a current challenge to satisfy the great world energy demand. There are several techniques to produce hydrogen either mature or under development. The election of the hydrogen production method will have a high impact on practical sustainability of the hydrogen economy. An important profile for the viability of a process is the calculation of energy and exergy efficiencies as well as their overall integration into the circular economy. To carry out theoretical energy and exergy analyses we have estimated proposed hydrogen production using different software (DWSIM and MATLAB) and reference conditions. The analysis consolidates methane reforming or auto-thermal reforming as the viable technologies at the present state of the art with reasonable energy and exergy efficiencies but pending on the impact of environmental constraints as CO2 emission countermeasures. However natural gas or electrolysis show very promising results and should be advanced in their technological and maturity scaling. Electrolysis shows a very good exergy efficiency due to the fact that electricity itself is a high exergy source. Pyrolysis exergy loses are mostly in the form of solid carbon material which has a very high integration potential into the hydrogen economy.
New Combustion Modelling Approach for Methane-Hydrogen Fueled Engines Using Machine Learning and Engine Virtualization
Oct 2021
Publication
The achievement of a carbon-free emissions economy is one of the main goals to reduce climate change and its negative effects. Scientists and technological improvements have followed this trend improving efficiency and reducing carbon and other compounds that foment climate change. Since the main contributor of these emissions is transportation detaching this sector from fossil fuels is a necessary step towards an environmentally friendly future. Therefore an evaluation of alternative fuels will be needed to find a suitable replacement for traditional fossil-based fuels. In this scenario hydrogen appears as a possible solution. However the existence of the drawbacks associated with the application of H2 -ICE redirects the solution to dual-fuel strategies which consist of mixing different fuels to reduce negative aspects of their separate use while enhancing the benefits. In this work a new combustion modelling approach based on machine learning (ML) modeling is proposed for predicting the burning rate of different mixtures of methane (CH4 ) and hydrogen (H2). Laminar flame speed calculations have been performed to train the ML model finding a faster way to obtain good results in comparison with actual models applied to SI engines in the virtual engine model framework.
Opportunities for Low-carbon Generation and Storage Technologies to Decarbonise the Future Power System
Feb 2023
Publication
Alternatives to cope with the challenges of high shares of renewable electricity in power systems have been addressed from different approaches such as energy storage and low-carbon technologies. However no model has previously considered integrating these technologies under stability requirements and different climate conditions. In this study we include this approach to analyse the role of new technologies to decarbonise the power system. The Spanish power system is modelled to provide insights for future applications in other regions. After including storage and low-carbon technologies (currently available and under development) batteries and hydrogen fuel cells have low penetration and the derived emission reduction is negligible in all scenarios. Compressed air storage would have a limited role in the short term but its performance improves in the long term. Flexible generation technologies based on hydrogen turbines and long-duration storage would allow the greatest decarbonisation providing stability and covering up to 11–14 % of demand in the short and long term. The hydrogen storage requirement is equivalent to 18 days of average demand (well below the theoretical storage potential in the region). When these solutions are considered decarbonising the electricity system (achieving Paris targets) is possible without a significant increase in system costs (< € 114/MWh).
Optimal Energy Management in a Standalone Microgrid, with Photovoltaic Generation, Short-Term Storage, and Hydrogen Production
Mar 2020
Publication
This paper addresses the energy management of a standalone renewable energy system. The system is configured as a microgrid including photovoltaic generation a lead-acid battery as a short term energy storage system hydrogen production and several loads. In this microgrid an energy management strategy has been incorporated that pursues several objectives. On the one hand it aims to minimize the amount of energy cycled in the battery in order to reduce the associated losses and battery size. On the other hand it seeks to take advantage of the long-term surplus energy producing hydrogen and extracting it from the system to be used in a fuel cell hybrid electric vehicle. A crucial factor in this approach is to accommodate the energy consumption to the energy demand and to achieve this a model predictive control (MPC) scheme is proposed. In this context proper models for solar estimation hydrogen production and battery energy storage will be presented. Moreover the controller is capable of advancing or delaying the deferrable loads from its prescheduled time. As a result a stable and efficient supply with a relatively small battery is obtained. Finally the proposed control scheme has been validated on a real case scenario.
Going Offshore or Not: Where to Generate Hydrogen in Future Integrated Energy Systems?
Jan 2023
Publication
Hydrogen can be key in the energy system transition. We investigate the role of offshore hydrogen generation in a future integrated energy system. By performing energy system optimisation in a model application of the Northern-central European energy system and the North Sea offshore grid towards 2050 we find that offshore hydrogen generation may likely only play a limited role and that offshore wind energy has higher value when sent to shore in the form of electricity. Forcing all hydrogen generation offshore would lead to increased energy system costs. Under the assumed scenario conditions which result in deep decarbonisation of the energy system towards 2050 hydrogen generation – both onshore and offshore – follows solar PV generation patterns. Combined with hydrogen storage this is the most cost-effective solution to satisfy future hydrogen demand. Overall we find that the role of future offshore hydrogen generation should not simply be derived from minimising costs for the offshore sub-system but by also considering the economic value that such generation would create for the whole integrated energy system. We find as a no-regret option to enable and promote the integration of offshore wind in onshore energy markets via electrical connections.
Multi-vector Energy Management System including Scheduling Electrolyser, Electric Vehicle Charging Station and Other Assets in a Real Scenario
Oct 2022
Publication
Today in the field of energy the main goal is to reduce emissions with 7 the aim of maintaining a clean environment. To reduce energy consumption 8 from fossil fuels new tools for micro-grids have been proposed. In the context 9 of multi-vector energy management systems the present work proposes an 10 optimal scheduler based on genetic algorithms to manage flexible assets in the 11 energy system such as energy storage and manageable demand. This tool is 12 applied to a case study for a Spanish technology park (360 kW consumption 13 peak) with photovoltaic and wind generation (735 kW generation peak) 14 hydrogen production (15 kW) and electric and fuel cell charging stations. 15 It provides an hourly day-ahead scheduling for the existing flexible assets: 16 the electrolyser the electric vehicle charging station the hydrogen refuelling 17 station and the heating ventilation and air conditioning system in one 18 building of the park. 19 A set of experiments is carried out over a period of 14 days using real 20 data and performing computations in real time in order to test and validate 21 the tool. The analysis of results show that the solution maximises the use of 22 local renewable energy production (demand is shifted to those hours when 23 there is a surplus of generation) which means a reduction in energy costs 24 whereas the computational cost allows the implementation of the tool in real 25 time.
Light-Driven Hydrogen Evolution Assisted by Covalent Organic Frameworks
Jun 2021
Publication
Covalent organic frameworks (COFs) are crystalline porous organic polymers built from covalent organic blocks that can be photochemically active when incorporating organic semiconducting units such as triazine rings or diacetylene bridges. The bandgap charge separation capacity porosity wettability and chemical stability of COFs can be tuned by properly choosing their constitutive building blocks by extension of conjugation by adjustment of the size and crystallinity of the pores and by synthetic post-functionalization. This review focuses on the recent uses of COFs as photoactive platforms for the hydrogen evolution reaction (HER) in which usually metal nanoparticles (NPs) or metallic compounds (generally Pt-based) act as co-catalysts. The most promising COF-based photocatalytic HER systems will be discussed and special emphasis will be placed on rationalizing their structure and light-harvesting properties in relation to their catalytic activity and stability under turnover conditions. Finally the aspects that need to be improved in the coming years will be discussed such as the degree of dispersibility in water the global photocatalytic efficiency and the robustness and stability of the hybrid systems putting emphasis on both the COF and the metal co-catalyst.
Methane Cracking as a Bridge Technology to the Hydrogen Economy
Nov 2016
Publication
Shifting the fossil fuel dominated energy system to a sustainable hydrogen economy could mitigate climate change through reduction of greenhouse gas emissions. Because it is estimated that fossil fuels will remain a significant part of our energy system until mid-century bridge technologies which use fossil fuels in an environmentally cleaner way offer an opportunity to reduce the warming impact of continued fossil fuel utilization. Methane cracking is a potential bridge technology during the transition to a sustainable hydrogen economy since it produces hydrogen with zero emissions of carbon dioxide. However methane feedstock obtained from natural gas releases fugitive emissions of methane a potent greenhouse gas that may offset methane cracking benefits. In this work a model exploring the impact of methane cracking implementation in a hydrogen economy is presented and the impact on global emissions of carbon dioxide and methane is explored. The results indicate that the hydrogen economy has the potential to reduce global carbon dioxide equivalent emissions between 0 and 27% when methane leakage from natural gas is relatively low methane cracking is employed to produce hydrogen and a hydrogen fuel cell is applied. This wide range is a result of differences between the scenarios and the CH4 leakage rates used in the scenarios. On the other hand when methane leakage from natural gas is relatively high methane steam reforming is employed to produce hydrogen and an internal combustion engine is applied the hydrogen economy leads to a net increase in global carbon dioxide equivalent emissions between 19 and 27%.
Model Predictive Control of an Off-sire Green Hydrogen Production and Refuelling Station
Jan 2023
Publication
The expected increase of hydrogen fuel cell vehicles has motivated the emergence of a significant number of studies on Hydrogen Refuelling Stations (HRS). Some of the main HRS topics are sizing location design optimization and optimal operation. On-site green HRS where hydrogen is produced locally from green renewable energy sources have received special attention due to their contribution to decarbonization. This kind of HRS are complex systems whose hydraulic and electric linked topologies include renewable energy sources electrolyzers buffer hydrogen tanks compressors and batteries among other components. This paper develops a linear model of a real on-site green HRS that is set to be built in Zaragoza Spain. This plant can produce hydrogen either from solar energy or from the utility grid and is designed for three different types of services: light-duty and heavy-duty fuel cell vehicles and gas containers. In the literature there is a lack of online control solutions developed for HRS even more in the form of optimal online control. Hence for the HRS operation a Model Predictive Controller (MPC) is designed to solve a weighted multi-objective online optimization problem taking into account the plant dynamics and constraints as well as the disturbances prediction. Performance is analysed throughout 210 individual month-long simulations and the effect of the multi-objective weighting prediction horizon and hydrogen selling price is discussed. With the simulation results this work shows the suitability of MPC for HRS control and its significant economic advantage compared to the rule-based control solution. In all simulations the MPC operation fulfils all required services. Moreover results show that a seven-day prediction horizon can improve profits by 57% relative to a one-day prediction horizon; that the battery is under-sized; or that the MPC operation strategy is more resolutive for low hydrogen selling prices.
Comparative Sustainability Study of Energy Storage Technologies Using Data Envelopment Analysis
Mar 2022
Publication
The transition to energy systems with a high share of renewable energy depends on the availability of technologies that can connect the physical distances or bridge the time differences between the energy supply and demand points. This study focuses on energy storage technologies due to their expected role in liberating the energy sector from fossil fuels and facilitating the penetration of intermittent renewable sources. The performance of 27 energy storage alternatives is compared considering sustainability aspects by means of data envelopment analysis. To this end storage alternatives are first classified into two clusters: fast-response and long-term. The levelized cost of energy energy and water consumption global warming potential and employment are common indicators considered for both clusters while energy density is used only for fast-response technologies where it plays a key role in technology selection. Flywheel reveals the highest efficiency between all the fast-response technologies while green ammonia powered with solar energy ranks first for long-term energy storage. An uncertainty analysis is incorporated to discuss the reliability of the results. Overall results obtained and guidelines provided can be helpful for both decision-making and research and development purposes. For the former we identify the most appealing energy storage options to be promoted while for the latter we report quantitative improvement targets that would make inefficient technologies competitive if attained. This contribution paves the way for more comprehensive studies in the context of energy storage by presenting a powerful framework for comparing options according to multiple sustainability indicators.
Critical Materials in PEMFC Systems and a LCA Analysis for the Potential Reduction of Environmental Impacts with EoL Strategies
Jul 2019
Publication
Commonly used materials constituting the core components of polymer electrolyte membrane fuel cells (PEMFCs) including the balance‐of‐plant were classified according to the EU criticality methodology with an additional assessment of hazardousness and price. A life‐cycle assessment (LCA) of the materials potentially present in PEMFC systems was performed for 1 g of each material. To demonstrate the importance of appropriate actions at the end of life (EoL) for critical materials a LCA study of the whole life cycle for a 1‐kW PEMFC system and 20000 operating hours was performed. In addition to the manufacturing phase four different scenarios of hydrogen production were analyzed. In the EoL phase recycling was used as a primary strategy with energy extraction and landfill as the second and third. The environmental impacts for 1 g of material show that platinum group metals and precious metals have by far the largest environmental impact; therefore it is necessary to pay special attention to these materials in the EoL phase. The LCA results for the 1‐kW PEMFC system show that in the manufacturing phase the major environmental impacts come from the fuel cell stack where the majority of the critical materials are used. Analysis shows that only 0.75 g of platinum in the manufacturing phase contributes on average 60% of the total environmental impacts of the manufacturing phase. In the operating phase environmentally sounder scenarios are the hydrogen production with water electrolysis using hydroelectricity and natural gas reforming. These two scenarios have lower absolute values for the environmental impact indicators on average compared with the manufacturing phase of the 1‐kW PEMFC system. With proper recycling strategies in the EoL phase for each material and by paying a lot of attention to the critical materials the environmental impacts could be reduced on average by 37.3% for the manufacturing phase and 23.7% for the entire life cycle of the 1‐kW PEMFC system.
Optimising Fuel Supply Chains within Planetary Boundaries: A Case Study of Hydrogen for Road Transport in the UK
Jul 2020
Publication
The world-wide sustainability implications of transport technologies remain unclear because their assessment often relies on metrics that are hard to interpret from a global perspective. To contribute to filling this gap here we apply the concept of planetary boundaries (PBs) i.e. a set of biophysical limits critical for operating the planet safely to address the optimal design of sustainable fuel supply chains (SCs) focusing on hydrogen for vehicle use. By incorporating PBs into a mixed-integer linear programming model (MILP) we identify SC configurations that satisfy a given transport demand while minimising the PBs transgression level i.e. while reducing the risk of surpassing the ecological capacity of the Earth. On applying this methodology to the UK we find that the current fossil-based sector is unsustainable as it transgresses the energy imbalance CO2 concentration and ocean acidification PBs heavily i.e. five to 55-fold depending on the downscale principle. The move to hydrogen would help to reduce current transgression levels substantially i.e. reductions of 9–86% depending on the case. However it would be insufficient to operate entirely within all the PBs concurrently. The minimum impact SCs would produce hydrogen via water electrolysis powered by wind and nuclear energy and store it in compressed form followed by distribution via rail which would require as much as 37 TWh of electricity per year. Our work unfolds new avenues for the incorporation of PBs in the assessment and optimisation of energy systems to arrive at sustainable solutions that are entirely consistent with the carrying capacity of the planet.
Waste Aluminum Application as Energy Valorization for Hydrogen Fuel Cells for Mobile Low Power Machines Applications
Nov 2021
Publication
This article proposes a new model of power supply for mobile low power machines applications between 10 W and 30 W such as radio-controlled (RC) electric cars. This power supply is based on general hydrogen from residual aluminum and water with NaOH so it is proposed energy valorization of aluminum waste. In the present research a theoretical model allows us to predict the requested aluminum surface and the required flow of hydrogen has been developed also considering in addition to the geometry and purity of the material two key variables as the temperature and the molarity of the alkaline solution used in the hydrogen production process. Focusing on hydrogen production isopropyl alcohol plays a key role in the reactor’s fuel cell vehicle as it filters out NaOH particles and maintains a constant flow of hydrogen for the operation of the machine keeping the reactor temperature controlled. Finally a comparison of the theoretical and experimental data has been used to validate the developed model using aluminum sheets from ring cans to generate hydrogen which will be used as a source of hydrogen in a power fuel cell of an RC car. Finally the manuscript shows the parts of the vehicle’s powertrain its behavior and mode of operation.
Recent Advances in Alkaline Exchange Membrane Water Electrolysis and Electrode Manufacturing
Oct 2021
Publication
Water electrolysis to obtain hydrogen in combination with intermittent renewable energy resources is an emerging sustainable alternative to fossil fuels. Among the available electrolyzer technologies anion exchange membrane water electrolysis (AEMWE) has been paid much attention because of its advantageous behavior compared to other more traditional approaches such as solid oxide electrolyzer cells and alkaline or proton exchange membrane water electrolyzers. Recently very promising results have been obtained in the AEMWE technology. This review paper is focused on recent advances in membrane electrode assembly components paying particular attention to the preparation methods for catalyst coated on gas diffusion layers which has not been previously reported in the literature for this type of electrolyzers. The most successful methodologies utilized for the preparation of catalysts including co-precipitation electrodeposition sol–gel hydrothermal chemical vapor deposition atomic layer deposition ion beam sputtering and magnetron sputtering deposition techniques have been detailed. Besides a description of these procedures in this review we also present a critical appraisal of the efficiency of the water electrolysis carried out with cells fitted with electrodes prepared with these procedures. Based on this analysis a critical comparison of cell performance is carried out and future prospects and expected developments of the AEMWE are discussed.
Hydrogen or Hydrogen-derived Methanol for Dual-fuel Compression-ignition Combustion: An Engine Perspective
Oct 2022
Publication
Synthetic fuels or e-fuels produced from captured CO2 and renewable hydrogen are envisaged as a feasible path towards a climate-neutral transportation in medium/heavy-duty and maritime sectors. EU is presently debating energy targets by 2030 for these fuels. As their production involves chemical processing of hydrogen it must be evaluated if the extra cost is worthy at least in applications where hydrogen use is possible. This manuscript focuses on the performance and environmental impact when hydrogen and methanol are fed to a heavy-duty compression-ignition engine working under dual-fuel combustion. The trade-off thermal efficiency-NOx emissions is primary considered in the assessment by combining both variables in an own defined function. During the work engine operating settings were adjusted to exploit the potential of methanol and hydrogen. Compared to conventional combustion methanol required centering the combustion towards TDC and doubling the EGR rate resulting in a low temperature highly premixed combustion almost soot-free and with extremely low NOx emissions. The best settings for hydrogen were in the middle of those for methanol and conventional combustion. Results showed great dependance with the engine load but methanol proved superior to hydrogen for all conditions. At high load 20–60 % methanol even improved the efficiency and reduced the NOx emissions obtained by conventional combustion. However at low load hydrogen could substitute 90 % of the diesel fuel while methanol failed at substitutions higher than 55 %.
Decarbonizing the Spanish Transportation Sector by 2050: Design and Techno-economic Assessment of the Hydrogen Generation and Supply Chain
May 2023
Publication
The transport sector is difficult to decarbonize due to its high reliance on fossil fuels accounting for 37% of global end-use sectors emissions in 2021. Therefore this work proposes an energy model to replace the Spanish vehicle fleet by hydrogen-fueled vehicles by 2050. Thus six regions are defined according to their proximity to regasification plants where hydrogen generation hubs are implemented. Likewise renewables deployment is subject to their land availability. Hydrogen is transported through an overhauled primary natural gas transport network while two distribution methods are compared for levelized cost of hydrogen minimization: gaseous pipeline vs liquid hydrogen supply in trucks. Hence a capacity of 443.1 GW of renewables 214 GW of electrolyzers and 3.45 TWh of hydrogen storage is required nationwide. Additionally gaseous hydrogen distribution is on average 17% cheaper than liquid hydrogen delivery. Finally all the regions present lower prices per km traveled than gasoline or diesel.
From Grey to Green and from West to East: The Geography and Innovation Trajectories of Hydrogen Fuel Technologies
May 2023
Publication
Despite the potential of hydrogen as a sustainable energy carrier existing studies analysing the recent evolution of this technology are scattered typically focusing on a specific type of hydrogen technology within a single country or region. In this paper we adopt a broader perspective providing an overview of the evolution of knowledge generation across different types of hydrogen fuel and the leading countries in developing new technologies in this field. Using data from the European Patent Office we map knowledge generation on hydrogen fuel technologies exploring its geographic distribution and its link with environmental sustainability. While the United States leads the generation of new knowledge other Asian and European countries show greater dynamism in growth and specialisation. Our study shows that although hydrogen fuel is considered environmentally friendly most recent technological developments are still related to fossil energy sources. However a faster growth rate is observed in the knowledge of hydrogen fuel from renewable sources pointing to a promising path towards sustainability. Moreover our analysis of the knowledge interconnection between different hydrogen types suggests that those technologies developed for hydrogen based on fossil energy sources have enabled novel applications based on renewable energies.
Life Cycle Assessment of an Autonomous Underwater Vehicle that Employs Hydrogen Fuel Cell
Aug 2023
Publication
In recent years there has been a significant increase in the adoption of autonomous vehicles for marine and submarine missions. The advancement of emerging imaging navigation and communication technologies has greatly expanded the range of operational capabilities and opportunities available. The ENDURUNS project is a European research endeavor focused on identifying strategies for achieving minimal environmental impact. To measure these facts this article evaluates the product impacts employing the Life Cycle Assessment methodology for the first time following the ISO 14040 standard. In this analysis the quantitative values of Damage and Environmental Impact using the Eco-Indicator 99 methodology in SimaPro software are presented. The results report that the main contributors in environmental impact terms have been placed during the manufacturing phase. Thus one of the challenges is accomplished avoiding the use phase emissions that are the focus to reduce nowadays in the marine industry.
No more items...