United Kingdom

As part of the LTS Futures HyTechnical project IGEM requested that DNV GL undertake an assessment of the possible impact of hydrogen transmission on BPDs to support the development of supplements to the existing suite of natural gas standards to accommodate the possible future use of hydrogen. The current state of knowledge of the behaviour of large scale high pressure hydrogen releases is limited in comparison with the considerable body of data from research and operational experience of natural gas but is adequate to undertake an impact assessment to take account of the different gas outflow and fire characteristics of 100% hydrogen vs. natural gas.<br/>Calculations of the BPDs for 100% hydrogen pipeline fires on an equivalent basis to those in IGEM/TD/1 for natural gas have been performed with a degree of confidence in the results and demonstrated that the equivalent BPDs for 100% hydrogen are approximately 10% smaller than for natural gas. The results are presented graphically in this report.<br/>However hydrogen introduces the potential for substantially higher overpressures than natural gas due to the higher flame speed and wider flammable limits if delayed ignition is a credible event. The overpressure estimates presented in this report are intended to be scoping calculations to put the likely overpressures into context. The results suggest that significant overpressures are possible at the BPDs but there is a lack of evidence to support the estimation of the overpressures following delayed ignition of a large turbulent hydrogen release in the open (in contrast to explosions in confined or congested regions) and there is a high degree of uncertainty in the predictions presented here. It is therefore recommended that large scale pipeline rupture experiments are performed similar to those undertaken previously for hydrogen natural gas and natural gas/hydrogen mixtures but with ignition engineered to take place after a short delay in order to measure the overpressures and provide the means to validate or refine the predictions made.<br/>The analysis has highlighted limitations in the original method of calculating BPDs in IGEM/TD/1 which reflects the techniques available at the time approximately 40 years ago. Since then understanding of the hazards from pipeline failures and the ability to model the consequences and predict the associated risks to people in the surrounding area have advanced very considerably facilitated by software tools and documented in standards such as IGEM/TD/2. These methods allow the highly transient nature of a high pressure gas pipeline rupture release to be modelled more accurately and for the thermal effects of fires on people and buildings to be calculated taking account of the time-varying thermal dose.<br/>For these reasons a simple comparison of the possible overpressure effects of delayed ignition of a 100% hydrogen release at the BPDs can be misleading and implies that the overpressure hazards could be more severe than those for fires which may not be the case. Example calculations have been performed for a representative pipeline case which indicate that using current methods the predicted thermal hazard distances for 100% hydrogen pipeline fires (house burning and escape for people) are substantially greater than those estimated for overpressures following delayed ignition for similar levels of vulnerability. This report addresses buried pipelines only – the potential for more severe explosion overpressure effects for hydrogen releases may be more significant for Above Ground Installations (AGIs) especially where congestion or confinement may be present. It is recommended that similar studies are conducted to quantify the effect of hydrogen conversion on the consequences and risks associated with hydrogen releases at AGIs.<br/>Finally it is stressed that the analysis in this report does not consider the relative risks for 100% hydrogen and the equivalent natural gas pipelines. There remain uncertainties in the failure frequencies for steel pipelines transporting hydrogen and particularly the probability of immediate and delayed ignition. The likelihood of delayed ignition of a large turbulent high pressure hydrogen gas pipeline rupture release may be very low due to the wider flammability limits and lower minimum ignition energy for hydrogen compared with natural gas. Additional research is currently ongoing or planned to address the gaps in knowledge for 100% hydrogen which should allow more robust comparisons of the relative risks to be made in the future.

The UK oil and gas sector is mature and a combination of a dwindling resource base and a move towards decarbonisation has led to lower investments and an increasing decommissioning bill. Many existing offshore assets are in the vicinity of potential renewable energy developments or low-carbon facilities. We propose a technical evaluation process to understand whether pipelines might be repurposed to reduce the costs of low-carbon energy investment and oil decommissioning. We identify survival analysis as an effective method to investigate the potential of pipelines repurposing based on historical failure records as it deals with acceptable levels of data gaps and does not require associated field costs for detailed inspection. It provides a close estimate of the anticipated remaining life when compared to feasibility studies. We use survival analysis to examine several repurposing case studies for low-carbon investments. It also demonstrates that several pipeline systems have the potential to operate safely beyond their design life. Detailed records of failure will allow for further development of this methodology in the future.

The underlying physical mechanisms leading to the generation of blast waves after liquid hydrogen (LH2) storage tank rupture in a fire are not yet fully understood. This makes it difficult to develop predictive models and validate them against a very limited number of experiments. This study aims at the development of a CFD model able to predict maximum pressure in the blast wave after the LH2 storage tank rupture in a fire. The performed critical review of previous works and the thorough numerical analysis of BMW experiments (LH2 storage pressure in the range 2.0e11.3 bar abs) allowed us to conclude that the maximum pressure in the blast wave is generated by gaseous phase starting shock enhanced by combustion reaction of hydrogen at the contact surface with heated by the shock air. The boiling liquid expanding vapour explosion (BLEVE) pressure peak follows the gaseous phase blast and is smaller in amplitude. The CFD model validated recently against high-pressure hydrogen storage tank rupture in fire experiments is essentially updated in this study to account for cryogenic conditions of LH2 storage. The simulation results provided insight into the blast wave and combustion dynamics demonstrating that combustion at the contact surface contributes significantly to the generated blast wave increasing the overpressure at 3 m from the tank up to 5 times. The developed CFD model can be used as a contemporary tool for hydrogen safety engineering e.g. for assessment of hazard distances from LH2 storage.

The demand for clean and sustainable energy solutions is escalating as the global population grows and economies develop. Fossil fuels which currently dominate the energy sector contribute to greenhouse gas emissions and environmental degradation. In response to these challenges hydrogen storage technologies have emerged as a promising avenue for achieving energy sustainability. This review provides an overview of recent advancements in hydrogen storage materials and technologies emphasizing the importance of efficient storage for maximizing hydrogen’s potential. The review highlights physical storage methods such as compressed hydrogen (reaching pressures of up to 70 MPa) and material-based approaches utilizing metal hydrides and carboncontaining substances. It also explores design considerations computational chemistry high-throughput screening and machine-learning techniques employed in developing efficient hydrogen storage materials. This comprehensive analysis showcases the potential of hydrogen storage in addressing energy demands reducing greenhouse gas emissions and driving clean energy innovation.

To situate its low-carbon transition process in longer-term real-world business contexts this article makes a longitudinal analysis of the UK petrochemical industry focusing on changing economic and socio-political environments and company strategies in the last 50 years. Using the Triple Embeddedness Framework the paper identifies two parallel and conflicting reorientation processes in the UK petrochemical industry. The first one which started in the 1970s and is driven by long-standing competitiveness problems led to retrenchment in the 1980s exit of incumbent companies (BP Shell ICI) and the entry of new firms (INEOS SABIC) in the 1990s and 2000s and diversification into upstream fossil fuel production and ethane imports in the 2010s. The second reorientation process which started in the 2010s is driven by climate change considerations and has led petrochemical firms to reluctantly explore low-carbon alternatives. Despite advancing ambitious visions and plans companies are weakly committed to low-carbon reorientation because this is layered on top of and conflicts with the deeper economically-motivated reorientation process. The paper further concludes that the industry's low-carbon plans and visions are partial because they focus more on some innovations (hydrogen-as-fuel CCS) than on other innovations (recycling bio-feedstocks synthetic feedstocks). Despite exploring alternatives firms also use political resistance strategies to hamper and delay deeper low-carbon reorientation

Hydrogen is emerging as one of the most promising energy carriers for a decarbonised global energy system. Transportation and storage of hydrogen are critical to its large-scale adoption and to these ends liquid hydrogen is being widely considered. The liquefaction and storage processes must however be both safe and efficient for liquid hydrogen to be viable as an energy carrier. Identifying the most promising liquefaction processes and associated transport and storage technologies is therefore crucial; these need to be considered in terms of a range of interconnected parameters ranging from energy consumption and appropriate materials usage to considerations of unique liquid-hydrogen physics (in the form of ortho–para hydrogen conversion) and boil-off gas handling. This study presents the current state of liquid hydrogen technology across the entire value chain whilst detailing both the relevant underpinning science (e.g. the quantum behaviour of hydrogen at cryogenic temperatures) and current liquefaction process routes including relevant unit operation design and efficiency. Cognisant of the challenges associated with a projected hydrogen liquefaction plant capacity scale-up from the current 32 tonnes per day to greater than 100 tonnes per day to meet projected hydrogen demand this study also reflects on the next-generation of liquid-hydrogen technologies and the scientific research and development priorities needed to enable them.

In this seventh episode Steffan Eldred Hydrogen Innovation Network Knowledge Transfer Manager and Jenni McDonnell MBE Heating and Cooling Knowledge Transfer Manager from Innovate UK KTN discuss why using hydrogen to generate heat is so important and explore the hydrogen economy opportunities and challenges within this sector alongside their special guest Jeff House Head of External Affairs Baxi Boilers.

The podcast can be found on their website.

In this episode Steffan Eldred Hydrogen Knowledge Transfer Manager and Debra Jones Chemistry Knowledge Transfer Manager from Innovate UK KTN talk about hydrogen combustion with special guest Duncan Engeham European Research and Development Director at Cummins Inc.

The podcast can be found on their website.

Ammonia is a pollutant present in wastewater and is also a valuable carbon-free hydrogen carrier. Stripping recovery and anodic oxidation of ammonia to produce hydrogen via electrolysis is gaining momentum as a technology yet the development of an inexpensive stable catalytic material is imperative to reduce cost. Here we report on a new nickel copper (NiCu) catalyst electrodeposited onto a high surface area nickel felt (NF) as an anode for ammonia electrolysis. Cyclic voltammetry demonstrated that the catalyst/substrate combination reached the highest current density (200 mA cm2 at 20 C) achieved for a non-noble metal catalyst. A NiCu/NF electrode was tested in an anion exchange membrane electrolyser for 50 h; it showed good stability and high Faradaic efficiency for ammonia oxidation (88%) and hydrogen production (99%). We demonstrate that this novel electrode catalyst/substrate material combination can oxidise ammonia in a scaled system and hydrogen can be produced as a valuable by-product at industrial-level current densities and cell voltages lower than that for water electrolysis.

Recent drastic increases in natural gas prices have brought into sharp focus the inherent tensions between net zero transitions energy security and affordability. We investigate the impact of different fuel prices on the energy system transition explicitly accounting for the increasingly coupled power and heating sectors and also incorporate the emerging hydrogen sector. The aim is to identify low-regret decisions and optimal energy system transitions for different fuel prices. We observe that the evolution of the heating sector is highly sensitive to the gas price whereas the composition of the power sector is not qualitatively impacted by gas prices. We also observe that bioenergy plays an important role in the energy system transition and the balance between gas price and biomass prices determines the optimal technology portfolios. The future evolution of the prices of these two resources is highly uncertain and future energy systems must be resilient to these uncertainties.

This net zero investment roadmap summarises government’s hydrogen policies and available investment opportunities.

Further development of hydrogen-fuelled transport and associated infrastructure requires fundamentally based validated and publicly accepted models for fuelling protocol development particularly for heavy-duty transport applications where protocols are not available yet. This study aims to use computational fluid dynamics (CFD) for modelling the entire hydrogen refuelling station (HRS) including all its components starting from high-pressure (HP) tanks a mass flow meter pressure control valve (PCV) a heat exchanger (HE) nozzle hose breakaway and up to 3 separate onboard tanks. The paper focuses on the initial phase of the refuelling procedure in which the main purpose is to check for leaks in the fuelling line and determine if it is safe to start fuelling. The simulation results are validated against the only publicly available data on hydrogen fuelling by Kuroki and co-authors (2021) from the NREL hydrogen fuelling station experiment. The simulation results – mass flow rate dynamics as well as pressure and temperature at different station locations - show good agreement with the measured experimental data. The development of such models is crucial for the further advancement of hydrogen-fuelled transport and infrastructure and this study presents a step towards this goal.

The UK government aims to transition its modern natural gas infrastructure towards Hydrogen by 2035. Since hydrogen is a much lighter gas than methane it is important to understand the change in parameters when transporting it. While most modern work in this topic looks at the transport of hydrogen-methane mixtures this work focuses on pure hydrogen transport. The aim of this paper is to highlight the change in gas distribution parameters when natural gas is replaced by hydrogen in the existing infrastructure. This study uses analytical models and computational models to compare the flow of hydrogen and methane in a pipe based on pressure loss. The Darcy-Weisbach and Colebrook-White equations were used for the analytical models and the k- ε model was used for the computational approach. The variables considered in the comparison were the pipe material (X52 Steel and MDPE) and pipe diameters (0.01m–1m). It was observed that hydrogen had to be transported 250–270% the velocity of methane to replicate flow for a fixed length of pipe. Furthermore it was noted that MDPE pipes has 2–31% lower pressure losses compared to X52 steel for all diameters when transporting hydrogen at a high velocity. Lastly it was noted that the analytical model and computational model were in agreement with 1–5% error in their findings.

National hydrogen strategies are emerging as a critical pillar of climate change policy. For homes connected to the gas grid hydrogen may offer an alternative decarbonisation pathway to electrification. Hydrogen production pathways in countries such as the UK will involve both the gas network and the electricity grid with related policy choices and investment decisions impacting the potential configuration of consumer acceptance for hydrogen homes. Despite the risk of public resistance be it on environmental economic or social grounds few studies have explored the emerging contours of domestic hydrogen acceptance. To date there is scarce evidence on public perceptions of national hydrogen policy and the extent to which attitudes may be rooted in prior knowledge and awareness or open to change following information provision and engagement. In response this study evaluates consumer preferences for a low-carbon energy future wherein parts of the UK housing stock may adopt low-carbon hydrogen boilers and hobs. Drawing on data from online focus groups we examine consumer perceptions of the government's twin-track approach which envisions important roles for both ‘blue’ and ‘green’ hydrogen to meet net zero ambitions. Through a mixed-methods multigroup analysis the underlying motivation is to explore whether the twin-track approach appears compatible with hydrogen acceptance. Moving forward hydrogen policy should ensure greater transparency concerning the benefits costs and risks of the transition with clearer communication about the justification for supporting respective hydrogen production pathways.

High-resolution direct numerical simulations are conducted for under-expanded cryogenic hydrogen gas jets to characterize the nearfield flow physics. The basic flow features and jet dynamics are analyzed in detail revealing the existence of four stages during early jet development namely (a) initial penetration (b) establishment of near-nozzle expansion (c) formation of downstream compression and (d) wave propagation. Complex acoustic waves are formed around the under-expanded jets. The jet expansion can also lead to conditions for local liquefaction from the pressurized cryogenic hydrogen gas release. A series of simulations are conducted with systematically varied nozzle pressure ratios and systematically changed exit diameters. The acoustic waves around the jets are found to waken with the decrease in the nozzle pressure ratio. The increase in the nozzle pressure ratio is found to accelerate hydrogen dispersion and widen the regions with hydrogen liquefaction potential. The increase in the nozzle exit diameter also widens the region with hydrogen liquefaction potential but slows down the evolution of the flow structures.

In this sixth episode Steffan Eldred Hydrogen Innovation Network Knowledge Transfer Manager and Debra Jones Chemistry Knowledge Transfer Manager from Innovate UK KTN discuss why converting waste to hydrogen is so important and explore the hydrogen transition opportunities and challenges in this sector alongside their special guest Rob Dent Senior Research Engineer - Energy Linde and Application Sales Engineer at BOC UK & Ireland.

The podcast can be found on their website.

This review critically analyses various aspects of the most promising thermochemical cycles for clean hydrogen production. While the current hydrogen market heavily relies on fossil-fuel-based platforms the thermochemical water-splitting systems based on the reduction-oxidation (redox) looping reactions have a significant potential to significantly contribute to the sustainable production of green hydrogen at scale. However compared to the water electrolysis techniques the thermochemical cycles suffer from a low technology readiness level (TRL) which retards the commercial implementation of these technologies. This review mainly focuses on identifying the capability of the state-of-the-art thermochemical cycles to deploy large-scale hydrogen production plants and their techno-economic performance. This study also analyzed the potential integration of the hybrid looping systems with the solar and nuclear reactor designs which are evidenced to be more cost-effective than the electrochemical water-splitting methods but it excludes fossil-based thermochemical processes such as gasification steam methane reforming and pyrolysis. Further investigation is still required to address the technical issues associated with implementing the hybrid thermochemical cycles in order to bring them to the market for sustainable hydrogen production.

Engineering tools for calculation of hazard distances for cryogenic hydrogen jets are currently missing. This study aims at the development of validated correlations for calculation of hazard distances for cryogenic unignited releases and jet fires. The experiments performed by Sandia National Laboratories (SNL) on jets from storage temperature in the range 46-295 K and pressure up to 6 bar abs are used to expand the validation domain of the correlations. The Ulster’s under-expanded jet theory is applied to calculate parameters at the real nozzle exit. The similarity law for concentration decay in momentum-dominated jets is shown to be capable to reproduce experimental data of SNL on 9 unignited cryogenic releases. The accuracy of the similarity law to predict experimentally measured axial concentration decay improves with the increase of the release diameter. This is thought due to decrease of the effect of friction and minor losses for large release orifices. The dimensionless flame length correlation is applied to analyse 30 cryogenic jet fire tests. The deviation of calculated flame length from measured in experiments is mostly within acceptable accuracy for engineering correlations 20% similarly to releases from storage and equipment at atmospheric temperatures. It is concluded that the similarity law and the dimensionless flame correlation can be used as universal engineering tools for calculation of hazard distances for hydrogen releases at any storage temperature including cryogenic.

The final session of the meeting consisted of a discussion panel to propose future directions for research in the field of hydrogen embrittlement and the potential impact of this research on public policy.

This article is a transcription of the recorded discussion of ‘Hydrogen Embrittlement: Future Directions’ at the Royal Society Scientific Discussion Meeting Challenges of Hydrogen and Metals Jan 16th–18th 2017. The text is approved by the contributors. H.L. transcribed the session and drafted the manuscript. Y.C. assisted in the preparation of the manuscript.

Link to document download on Royal Society Website 

The bioanode is important for a microbial electrolysis cell (MEC) and its robustness to maintain its catalytic activity affects the performance of the whole system. Bioanodes enriched at a potential of +0.2 V (vs. standard hydrogen electrode) were able to sustain their oxidation activity when the anode potential was varied from -0.3 up to +1.0 V. Chronoamperometric test revealed that the bioanode produced peak current density of 0.36 A/m2 and 0.37 A/m2 at applied potential 0 and +0.6 V respectively. Meanwhile hydrogen production at the biocathode was proportional to the applied potential in the range from -0.5 to  -1.0 V. The highest production rate was 7.4 L H2/(m2 cathode area)/day at -1.0 V cathode potential. A limited current output at the bioanode could halt the biocathode capability to generate hydrogen. Therefore maximum applied potential that can be applied to the biocathode was calculated as -0.84 V without overloading the bioanode.

This work programme was focused on identifying a suitable odorant for use in a 100% hydrogen gas grid (domestic use such as boilers and cookers). The research involved a review of existing odorants (used primarily for natural gas) and the selection of five suitable odorants based on available literature. One odorant was selected based on possible suitability with a Polymer Electrolyte Membrane (PEM) based fuel cell vehicle which could in future be a possible end-user of grid hydrogen. NPL prepared Primary Reference Materials containing the five odorants in hydrogen at the relevant amount fraction levels (as would be found in the grid) including ones provided by Robinson Brothers (the supplier of odorants for natural gas in the UK). These mixtures were used by NPL to perform tests to understand the effects of the mixtures on pipeline (metal and plastic) appliances (a hydrogen boiler provided by Worcester Bosch) and PEM fuel cells. HSE investigated the health and environmental impact of these odorants in hydrogen. Olfactory testing was performed by Air Spectrum to characterise the ‘smell’ of each odorant. Finally an economic analysis was performed by E4tech. The results confirm that Odorant NB would be a suitable odorant for use in a 100% hydrogen gas grid for combustion applications but further research would be required if the intention is to supply grid hydrogen to stationery fuel cells or fuel cell vehicles. In this case further testing would need to be performed to measure the extent of fuel cell degradation caused by the non-sulphur odorant obtained as part of this work programme and also other UK projects such as the Hydrogen Grid to Vehicle (HG2V) project would provide important information about whether a purification step would be required regardless of the odorant before the hydrogen purity would be suitable for a PEM fuel cell vehicle. If purification was required it would be fine to use Odorant NB as this would be removed during the purification step.

This report and any attachment is freely available on the ENA Smarter Networks Portal here. IGEM Members can download the report and any attachment directly by clicking on the pdf icon above.

The hydrogen economy is a proposition for the distribution of energy by using hydrogen in order to potentially eliminate carbon emissions and end our reliance on fossil fuels. Some futuristic forecasters view the hydrogen economy as the ultimate carbon free economy. Hydrogen operated vehicles are on trial in many countries. The use of hydrogen as an energy source for buildings is in its infancy but research and development is evolving. Hydrogen is generally fed into devices called fuel cells to produce energy. A fuel cell is an electrochemical device that produces electricity and heat from a fuel (often hydrogen) and oxygen. Fuel cells have a number of advantages over other technologies for power generation. When fed with clean hydrogen they have the potential to use less fuel than competing technologies and to emit no pollution (the only bi-product being water). However hydrogen has to be produced and stored in the first instance. It is possible to generate hydrogen from renewable sources but the technology is still immature and the transformation is wasteful. The creation of a clean hydrogen production and distribution economy at a global level is very costly. Proponents of a world-scale hydrogen economy argue that hydrogen can be an environmentally cleaner source of energy to end-users particularly in transportation applications without release of pollutants (such as particulate matter) or greenhouse gases at the point of end use. Critics of a hydrogen economy argue that for many planned applications of hydrogen direct use of electricity or production of liquid synthetic fuels from locally-produced hydrogen and CO2 (e.g. methanol economy) might accomplish many of the same net goals of a hydrogen economy while requiring only a small fraction of the investment in new infrastructure. This paper reviews the hydrogen economy how it is produced and distributed. It then investigates the different types of fuel cells and identifies which types are relevant to the built environment both in residential and nonresidential sections. It concludes by examining what are the future plans in terms of implementing fuel cells in the built environment and discussing some of the needs of built environment sector.



Link to Document

According to the UK’s Committee on Climate Change the economically efficient achievement of Government’s legally-binding carbon-reduction target will require full decarbonisation of all heat in buildings and the decarbonisation of most industrial heat over the next 20 to 30 years (BEIS 2018). This goliath task is not unprecedented. Indeed the scale of this transition is similar to the UK’s former transition from coal to natural gas heating. Albeit the rate of transition away from natural gas will certainly need to be greater than the rate of the transition toward natural gas to achieve net zero greenhouse gas emissions by 2050.<br/><br/>At present Government’s commitment stands in sharp contrast with its inaction on heat decarbonisation to date. Under pressure to progress this agenda Government has charged the Clean Heat Directorate with the task of outlining the process for determining the UK’s long-term heat policy framework to be published in the ‘Roadmap for policy on heat decarbonisation’ in the summer of 2020 (BEIS 2017). This report resulting from one of six EPSRC-funded secondments is designed to support early thinking on the roadmap by answering the research question: How can ‘Transitions’ research informs the roadmap for governing the UK’s heating transition?<br/><br/>‘Transitions’ research is an interdisciplinary field of study within the Social Sciences and Humanities that investigates the co-evolution of social and technological systems (such as the UK heating system) and the dynamics by which fundamental change in these systems occur. To investigate what insights this area of research may hold for the governance of the UK’s heat transition a systematic literature review was conducted focusing specifically on past and ongoing heat transitions across Europe.<br/><br/>The review uncovered learnings about the role of path dependency; power and politics; complexity; cross-sector interactions; multi-level governance; and intermediaries in shaping non-linear transitions toward renewable heat. This report illustrates each learning with real-world examples from case studies undertaken by Transitions researchers and concludes with a long list of policy and process-oriented governance recommendations for the UK Government.

Magnesium hydride owns the largest share of publications on solid materials for hydrogen storage. The “Magnesium group” of international experts contributing to IEA Task 32 “Hydrogen Based Energy Storage” recently published two review papers presenting the activities of the group focused on magnesium hydride based materials and on Mg based compounds for hydrogen and energy storage. This review article not only overviews the latest activities on both fundamental aspects of Mg-based hydrides and their applications but also presents a historic overview on the topic and outlines projected future developments. Particular attention is paid to the theoretical and experimental studies of Mg-H system at extreme pressures kinetics and thermodynamics of the systems based on MgH₂ nanostructuring new Mg-based compounds and novel composites and catalysis in the Mg based H storage systems. Finally thermal energy storage and upscaled H storage systems accommodating MgH₂ are presented.

This session contained talks on the characterization of hydrogen-enhanced corrosion of steels and nickel-based alloys emphasizing the different observations across length scales from atomic-scale spectrographic to macro-scale fractographic examinations.

This article is the transcription of the recorded discussion of the session ‘Hydrogen Effects in Corrosion’ at the Royal Society discussion meeting Challenges of Hydrogen and Metals 16–18 January 2017. The text is approved by the contributors. M.A.S. transcribed the session and E.L.S. assisted in the preparation of the manuscript.

Link to document download on Royal Society Website