- Home
- Institution of Gas Engineers & Managers
Institution of Gas Engineers & Managers
Living Carbon Free – Exploring What a Net-zero Target Means for Households
Jun 2019
Publication
The Energy Systems Catapult (ESC) explored the role of households in a net-zero emissions society to accompany the CCC’s Net Zero report looking at opportunities and challenges for households to reduce emissions from today’s levels and to support the stretch from an 80% emissions reduction to a net-zero greenhouse gas target. As well as describing a net-zero emissions world for households of different types the ESC looked at average household emissions under different decarbonisation scenarios and the options households can take to contribute to the decarbonisation effort.
This supported the Net Zero Technical report.
This supported the Net Zero Technical report.
Quantitative Evaluations of Hydrogen Diffusivity in V-X (X = Cr, Al, Pd) Alloy Membranes Based on Hydrogen Chemical Potential
Jan 2021
Publication
Vanadium (V) has higher hydrogen permeability than Pd-based alloy membranes but exhibits poor resistance to hydrogen-induced embrittlement. The alloy elements are added to reduce hydrogen solubility and prevent hydrogen-induced embrittlement. To enhance hydrogen permeability the alloy elements which improve hydrogen diffusivity in V are more suitable. In the present study hydrogen diffusivity in V-Cr V-Al and V-Pd alloy membranes was investigated in view of the hydrogen chemical potential and compared with the previously reported results of V-Fe alloy membranes. The additions of Cr and Fe to V improved the mobility of hydrogen atoms. In contrast those of Al and Pd decreased hydrogen diffusivity. The first principle calculations revealed that the hydrogen atoms cannot occupy the first-nearest neighbour T sites (T1 sites) of Al and Pd in the V crystal lattice. These blocking effects will be a dominant contributor to decreasing hydrogen diffusivity by the additions of Al and Pd. For V-based alloy membranes Fe and Cr are more suitable alloy elements compared with Al and Pd in view of hydrogen diffusivity.
Boosting Photocatalytic Hydrogen Production from Water by Photothermally Induced Biphase Systems
Feb 2021
Publication
Solar-driven hydrogen production from water using particulate photocatalysts is considered the most economical and effective approach to produce hydrogen fuel with little environmental concern. However the efficiency of hydrogen production from water in particulate photocatalysis systems is still low. Here we propose an efficient biphase photocatalytic system composed of integrated photothermal–photocatalytic materials that use charred wood substrates to convert liquid water to water steam simultaneously splitting hydrogen under light illumination without additional energy. The photothermal–photocatalytic system exhibits biphase interfaces of photothermally-generated steam/photocatalyst/hydrogen which significantly reduce the interface barrier and drastically lower the transport resistance of the hydrogen gas by nearly two orders of magnitude. In this work an impressive hydrogen production rate up to 220.74 μmol h−1 cm−2 in the particulate photocatalytic systems has been achieved based on the wood/CoO system demonstrating that the photothermal–photocatalytic biphase system is cost-effective and greatly advantageous for practical applications.
Performance Evaluation of Empirical Models for Vented Lean Hydrogen Explosions
Sep 2017
Publication
Explosion venting is a method commonly used to prevent or minimize damage to an enclosure caused by an accidental explosion. An estimate of the maximum overpressure generated though explosion is an important parameter in the design of the vents. Various engineering models (Bauwens et al. 2012 Molkov and Bragin 2015) and European (EN 14994 ) and USA standards (NFPA 68) are available to predict such overpressure. In this study their performance is evaluated using a number of published experiments. Comparison of pressure predictions from various models have also been carried out for the recent experiments conducted by GexCon using a 20 feet ISO container. The results show that the model of Bauwens et al. (2012) predicts well for hydrogen concentration between 16% and 21% and in the presence of obstacles. The model of Molkov et al. (2015) is found to work well for hydrogen concentrations between 10% and 30% without obstacles. In the presence of obstacles as no guidelines are given to set the coefficient for obstacles in the model it was necessary to tune the coefficient to match the experimental data. The predictions of the formulas in NFPA 68 show a large scatter across different tests. The current version of both EN 14994 and NFPA 68 are found to have very limited range of applicability and can hardly be used for vent sizing of hydrogen-air deflagrations. Overall the accuracy of all the engineering models was found to be limited. Some recommendations concerning their applicability will be given for vented lean-hydrogen explosion concentrations of interest to practical applications.
Hydrogen‐Rich Gas Production from Two‐Stage Catalytic Pyrolysis of Pine Sawdust with Calcined Dolomite
Jan 2022
Publication
Tao Xu,
Jue Xu and
Yongping Wu
The potential of catalytic pyrolysis of biomass for hydrogen and bio‐oil production has drawn great attention due to the concern of clean energy utilization and decarbonization. In this paper the catalytic pyrolysis of pine sawdust with calcined dolomite was carried out in a novel moving bed reactor with a two‐stage screw feeder. The effects of pyrolysis temperature (700–900 °C) and catalytic temperature (500–800 °C) on pyrolysis performance were investigated in product distribution gas composition and gas properties. The results showed that with the temperature increased pyrolysis gas yield in‐ creased but the yield of solid and liquid products decreased. With the increase in temperature the CO and H2 content increased significantly while the CO2 and CH4 decreased correspondingly. The calcined dolomite can remove the tar by 44% and increased syngas yield by 52.9%. With the increasing catalytic temperature the catalytic effect of calcined dolomite was also enhanced.
The Pathway to Net Zero Heating in the UK: A UKERC Policy Brief
Oct 2020
Publication
There is uncertainty over how heating might practically be decarbonised in the future. This briefing provides some clarity about the possible pathways forward focusing on the next 5-10 years.<br/>Meeting the UK government’s net zero emissions goal for 2050 will only be possible by complete decarbonisation of the building stock (both existing and new). There is uncertainty over the extent to which heating might practically be decarbonised in the future and what the optimal technologies may be. This paper provides some clarity about the pathways forward focusing on the next 5-10 years.
Pathways to Low-cost Clean Hydrogen Production with Gas Switching Reforming
Feb 2020
Publication
Gas switching reforming (GSR) is a promising technology for natural gas reforming with inherent CO2 capture. Like conventional steam methane reforming (SMR) GSR can be integrated with CO2 -gas shift and pressure swing adsorption units for pure hydrogen production. The resulting GSR-H2 process concept was techno-economically assessed in this study. Results showed that GSR-H2 can achieve 96% CO2 capture at a CO2 avoidance cost of 15 $/ton (including CO2 transport and storage). Most components of the GSR-H2 process are proven technologies but long-term oxygen carrier stability presents an important technical uncertainty that can adversely affect competitiveness when the material lifetime drops below one year. Relative to the SMR benchmark GSR-H2 replaces some fuel consumption with electricity consumption making it more suitable to regions with higher natural gas prices and lower electricity prices. Some minor alterations to the process configuration can adjust the balance between fuel and electricity consumption to match local market conditions. The most attractive commercialization pathway for the GSR-H2 technology is initial construction without CO2 capture followed by simple retrofitting for CO2 capture when CO2 taxes rise and CO2 transport and storage infrastructure becomes available. These features make the GSR-H2 technology robust to almost any future energy market scenario.
How Far Away is Hydrogen? Its Role in the Medium and Long-term Decarbonisation of the European Energy System
Nov 2015
Publication
Hydrogen is a promising avenue for decarbonising energy systems and providing flexibility. In this paper the JRC-EU-TIMES model – a bottom-up technology-rich model of the EU28 energy system – is used to assess the role of hydrogen in a future decarbonised Europe under two climate scenarios current policy initiative (CPI) and long-term decarbonisation (CAP). Our results indicate that hydrogen could become a viable option already in 2030 – however a long-term CO2 cap is needed to sustain the transition. In the CAP scenario the share of hydrogen in the final energy consumption of the transport and industry sectors reaches 5% and 6% by 2050. Low-carbon hydrogen production technologies dominate and electrolysers provide flexibility by absorbing electricity at times of high availability of intermittent sources. Hydrogen could also play a significant role in the industrial and transport sectors while the emergence of stationary hydrogen fuel cells for hydrogen-to-power would require significant cost improvements over and above those projected by the experts.
Opportunities and Challenges of Low-Carbon Hydrogen via Metallic Membranes
Jun 2020
Publication
Today electricity & heat generation transportation and industrial sectors together produce more than 80% of energy-related CO2 emissions. Hydrogen may be used as an energy carrier and an alternative fuel in the industrial residential and transportation sectors for either heating energy production from fuel cells or direct fueling of vehicles. In particular the use of hydrogen fuel cell vehicles (HFCVs) has the potential to virtually eliminate CO2 emissions from tailpipes and considerably reduce overall emissions from the transportation sector. Although steam methane reforming (SMR) is the dominant industrial process for hydrogen production environmental concerns associated with CO2 emissions along with the process intensification and energy optimization are areas that still require improvement. Metallic membrane reactors (MRs) have the potential to address both challenges. MRs operate at significantly lower pressures and temperatures compared with the conventional reactors. Hence the capital and operating expenses could be considerably lower compared with the conventional reactors. Moreover metallic membranes specifically Pd and its alloys inherently allow for only hydrogen permeation making it possible to produce a stream of up to 99.999+% purity.
For smaller and emerging hydrogen markets such as the semiconductor and fuel cell industries Pd-based membranes may be an appropriate technology based on the scales and purity requirements. In particular at lower hydrogen production rates in small-scale plants MRs with CCUS could be competitive compared to centralized H2 production. On-site hydrogen production would also provide a self-sufficient supply and further circumvent delivery delays as well as issues with storage safety. In addition hydrogen-producing MRs are a potential avenue to alleviate carbon emissions. However material availability Pd cost and scale-up potential on the order of 1.5 million m3/day may be limiting factors preventing wider application of Pd-based membranes.
Regarding the economic production of hydrogen the benchmark by the year 2020 has been determined and set in place by the U.S. DOE at less than $2.00 per kg of produced hydrogen. While the established SMR process can easily meet the set limit by DOE other carbon-free processes such as water electrolysis electron beam radiolysis and gliding arc technologies do not presently meet this requirement. In particular it is expected that the cost of hydrogen produced from natural gas without CCUS will remain the lowest among all of the technologies while the hydrogen cost produced from an SMR plant with solvent-based carbon capture could be twice as expensive as the conventional SMR without carbon capture. Pd-based MRs have the potential to produce hydrogen at competitive prices with SMR plants equipped with carbon capture.
Despite the significant improvements in the electrolysis technologies the cost of hydrogen produced by electrolysis may remain significantly higher in most geographical locations compared with the hydrogen produced from fossil fuels. The cost of hydrogen via electrolysis may vary up to a factor of ten depending on the location and the electricity source. Nevertheless due to its modular nature the electrolysis process will likely play a significant role in the hydrogen economy when implemented in suitable geographical locations and powered by renewable electricity.
This review provides a critical overview of the opportunities and challenges associated with the use of the MRs to produce high-purity hydrogen with low carbon emissions. Moreover a technoeconomic review of the potential methods for hydrogen production is provided and the drawbacks and advantages of each method are presented and discussed.
For smaller and emerging hydrogen markets such as the semiconductor and fuel cell industries Pd-based membranes may be an appropriate technology based on the scales and purity requirements. In particular at lower hydrogen production rates in small-scale plants MRs with CCUS could be competitive compared to centralized H2 production. On-site hydrogen production would also provide a self-sufficient supply and further circumvent delivery delays as well as issues with storage safety. In addition hydrogen-producing MRs are a potential avenue to alleviate carbon emissions. However material availability Pd cost and scale-up potential on the order of 1.5 million m3/day may be limiting factors preventing wider application of Pd-based membranes.
Regarding the economic production of hydrogen the benchmark by the year 2020 has been determined and set in place by the U.S. DOE at less than $2.00 per kg of produced hydrogen. While the established SMR process can easily meet the set limit by DOE other carbon-free processes such as water electrolysis electron beam radiolysis and gliding arc technologies do not presently meet this requirement. In particular it is expected that the cost of hydrogen produced from natural gas without CCUS will remain the lowest among all of the technologies while the hydrogen cost produced from an SMR plant with solvent-based carbon capture could be twice as expensive as the conventional SMR without carbon capture. Pd-based MRs have the potential to produce hydrogen at competitive prices with SMR plants equipped with carbon capture.
Despite the significant improvements in the electrolysis technologies the cost of hydrogen produced by electrolysis may remain significantly higher in most geographical locations compared with the hydrogen produced from fossil fuels. The cost of hydrogen via electrolysis may vary up to a factor of ten depending on the location and the electricity source. Nevertheless due to its modular nature the electrolysis process will likely play a significant role in the hydrogen economy when implemented in suitable geographical locations and powered by renewable electricity.
This review provides a critical overview of the opportunities and challenges associated with the use of the MRs to produce high-purity hydrogen with low carbon emissions. Moreover a technoeconomic review of the potential methods for hydrogen production is provided and the drawbacks and advantages of each method are presented and discussed.
Adsorption-Based Hydrogen Storage in Activated Carbons and Model Carbon Structures
Jul 2021
Publication
The experimental data on hydrogen adsorption on five nanoporous activated carbons (ACs) of various origins measured over the temperature range of 303–363 K and pressures up to 20 MPa were compared with the predictions of hydrogen density in the slit-like pores of model carbon structures calculated by the Dubinin theory of volume filling of micropores. The highest amount of adsorbed hydrogen was found for the AC sample (ACS) prepared from a polymer mixture by KOH thermochemical activation characterized by a biporous structure: 11.0 mmol/g at 16 MPa and 303 K. The greatest volumetric capacity over the entire range of temperature and pressure was demonstrated by the densest carbon adsorbent prepared from silicon carbide. The calculations of hydrogen density in the slit-like model pores revealed that the optimal hydrogen storage depended on the pore size temperature and pressure. The hydrogen adsorption capacity of the model structures exceeded the US Department of Energy (DOE) target value of 6.5 wt.% starting from 200 K and 20 MPa whereas the most efficient carbon adsorbent ACS could achieve 7.5 wt.% only at extremely low temperatures. The initial differential molar isosteric heats of hydrogen adsorption in the studied activated carbons were in the range of 2.8–14 kJ/mol and varied during adsorption in a manner specific for each adsorbent.
Energy Innovation Needs Assessment: Road Transport
Nov 2019
Publication
The Energy Innovation Needs Assessment (EINA) aims to identify the key innovation needs across the UK’s energy system to inform the prioritisation of public sector investment in low-carbon innovation. Using an analytical methodology developed by the Department for Business Energy & Industrial Strategy (BEIS) the EINA takes a system level approach and values innovations in a technology in terms of the system-level benefits a technology innovation provides. This whole system modelling in line with BEIS’s EINA methodology was delivered by the Energy Systems Catapult (ESC) using the Energy System Modelling Environment (ESMETM) as the primary modelling tool.
To support the overall prioritisation of innovation activity the EINA process analyses key technologies in more detail. These technologies are grouped together into sub-themes according to the primary role they fulfil in the energy system. For key technologies within a sub-theme innovations and business opportunities are identified. The main findings at the technology level are summarised in sub-theme reports. An overview report will combine the findings from each sub-theme to provide a broad system-level perspective and prioritisation.
This EINA analysis is based on a combination of desk research by a consortium of economic and engineering consultants and stakeholder engagement. The prioritisation of innovation and business opportunities presented is informed by a workshop organised for each sub-theme assembling key stakeholders from the academic community industry and government.
This report was commissioned prior to advice being received from the CCC on meeting a net zero target and reflects priorities to meet the previous 80% target in 2050. The newly legislated net zero target is not expected to change the set of innovation priorities rather it will make them all more valuable overall. Further work is required to assess detailed implications.
To support the overall prioritisation of innovation activity the EINA process analyses key technologies in more detail. These technologies are grouped together into sub-themes according to the primary role they fulfil in the energy system. For key technologies within a sub-theme innovations and business opportunities are identified. The main findings at the technology level are summarised in sub-theme reports. An overview report will combine the findings from each sub-theme to provide a broad system-level perspective and prioritisation.
This EINA analysis is based on a combination of desk research by a consortium of economic and engineering consultants and stakeholder engagement. The prioritisation of innovation and business opportunities presented is informed by a workshop organised for each sub-theme assembling key stakeholders from the academic community industry and government.
This report was commissioned prior to advice being received from the CCC on meeting a net zero target and reflects priorities to meet the previous 80% target in 2050. The newly legislated net zero target is not expected to change the set of innovation priorities rather it will make them all more valuable overall. Further work is required to assess detailed implications.
Commercialisation of Energy Storage
Mar 2015
Publication
This report was created to ensure a deeper understanding of the role and commercial viability of energy storage in enabling increasing levels of intermittent renewable power generation. It was specifically written to inform thought leaders and decision-makers about the potential contribution of storage in order to integrate renewable energy sources (RES) and about the actions required to ensure that storage is allowed to compete with the other flexibility options on a level playing field.<br/>The share of RES in the European electric power generation mix is expected to grow considerably constituting a significant contribution to the European Commission’s challenging targets to reduce greenhouse gas emissions. The share of RES production in electricity demand should reach about 36% by 2020 45-60% by 2030 and over 80% in 2050.<br/>In some scenarios up to 65% of EU power generation will be covered by solar photovoltaics (PV) as well as on- and offshore wind (variable renewable energy (VRE) sources) whose production is subject to both seasonal as well as hourly weather variability. This is a situation the power system has not coped with before. System flexibility needs which have historically been driven by variable demand patterns will increasingly be driven by supply variability as VRE penetration increases to very high levels (50% and more).<br/>Significant amounts of excess renewable energy (on the order of TWh) will start to emerge in countries across the EU with surpluses characterized by periods of high power output (GW) far in excess of demand. These periods will alternate with times when solar PV and wind are only generating at a fraction of their capacity and non-renewable generation capacity will be required.<br/>In addition the large intermittent power flows will put strain on the transmission and distribution network and make it more challenging to ensure that the electricity supply matches demand at all times.<br/>New systems and tools are required to ensure that this renewable energy is integrated into the power system effectively. There are four main options for providing the required flexibility to the power system: dispatchable generation transmission and distribution expansion demand side management and energy storage. All of these options have limitations and costs and none of them can solve the RES integration challenge alone. This report focuses on the question to what extent current and new storage technologies can contribute to integrate renewables in the long run and play additional roles in the short term.
A Review of Techno-economic Data for Road Transportation Fuels
May 2019
Publication
Worldwide the road transport sector typically arises as one of the main sources of air pollutants due to its high energy intensity and the use of fossil fuels. Thus governments and social agents work on the development and prospective planning of decarbonisation strategies oriented towards sustainable transport. In this regard the increase in the use of alternative fuels is the recurrent approach to energy planning e.g. through the promotion of electric vehicles biofuels natural gas liquefied petroleum gas etc. However there is a lack of comprehensive information on the techno-economic performance of production pathways for alternative fuels. The acquisition of robust techno-economic data is still a challenge for energy planners modellers analysts and policy-makers when building their prospective models to support decision-making processes. Hence this article aims to fill this gap through a deep literature review including the most representative production routes for a wide range of road transportation fuels. This led to the development of datasets including investment costs operating and maintenance costs and transformation efficiencies for more than 40 production pathways. The techno-economic data presented in this work are expected to be especially useful to those energy actors interested in performing long-term studies on the transition to a sustainable transport system.
Accelerating to Net Zero with Hydrogen Blending Standards Development in the UK, Canada and the US - Part 1
Mar 2021
Publication
"Hydrogen is expected to play a critical role in the move to a net-zero economy. However large-scale deployment is still in its infancy and there is still much to be done before we can blend hydrogen in large volumes into gas networks and ramp up the production that is required to meet demands of the energy transport and industry sectors. KTN Global Alliance will host two webinars to explore these challenges and opportunities in hydrogen blending on the 2nd and 3rd March 2021.
Exciting pilot projects are being conducted and explored in the UK Canada and US states such as California to determine the technical feasibility of blending hydrogen into existing natural gas systems. Whilst the deployment of hydrogen is in its early stages there is increasing interest around permitting significant percentage blends of hydrogen into gas networks which would enable the carbon intensity of gas supplies to be reduced creating a new demand for hydrogen and with the use of separation and purification technologies downstream support the transportation of pure hydrogen to markets.
Gaps in codes and standards need to be addressed to enable adoption and there may be opportunities for international collaboration and harmonisation to ensure that best practices are shared globally and to facilitate the growth of trade and export markets. There is an opportunity for the UK Canada and US three G7 countries to work together and show market making leadership in key enabling regulation for the new hydrogen economy.
Delivered by KTN Global Alliance on behalf of the British Consulate-General in Vancouver and the UK Science and Innovation Network in Canada and the US these two webinars will showcase hydrogen blending pilot projects in the UK Canada and California highlighting challenges and opportunities with regard to standards development for hydrogen blending and supporting further transatlantic collaboration in this area. The events also form part of the UK’s international engagement to build momentum towards a successful outcome at COP26 the UN climate summit that the UK will host in Glasgow in November 2021. The webinars will bring together experts from industry academia and policy from the UK Canada and California. Attendees will have an opportunity to ask questions and interact using Mentimeter."
Part 2 Highlights and Perspectives from Canada and California can be found here.
Exciting pilot projects are being conducted and explored in the UK Canada and US states such as California to determine the technical feasibility of blending hydrogen into existing natural gas systems. Whilst the deployment of hydrogen is in its early stages there is increasing interest around permitting significant percentage blends of hydrogen into gas networks which would enable the carbon intensity of gas supplies to be reduced creating a new demand for hydrogen and with the use of separation and purification technologies downstream support the transportation of pure hydrogen to markets.
Gaps in codes and standards need to be addressed to enable adoption and there may be opportunities for international collaboration and harmonisation to ensure that best practices are shared globally and to facilitate the growth of trade and export markets. There is an opportunity for the UK Canada and US three G7 countries to work together and show market making leadership in key enabling regulation for the new hydrogen economy.
Delivered by KTN Global Alliance on behalf of the British Consulate-General in Vancouver and the UK Science and Innovation Network in Canada and the US these two webinars will showcase hydrogen blending pilot projects in the UK Canada and California highlighting challenges and opportunities with regard to standards development for hydrogen blending and supporting further transatlantic collaboration in this area. The events also form part of the UK’s international engagement to build momentum towards a successful outcome at COP26 the UN climate summit that the UK will host in Glasgow in November 2021. The webinars will bring together experts from industry academia and policy from the UK Canada and California. Attendees will have an opportunity to ask questions and interact using Mentimeter."
Part 2 Highlights and Perspectives from Canada and California can be found here.
Dispersion of Cryogenic Hydrogen Through High-aspect Ratio Nozzles
Sep 2019
Publication
Liquid hydrogen is increasingly being used as a delivery and storage medium for stations that provide compressed gaseous hydrogen for fuel cell electric vehicles. In efforts to provide scientific justification for separation distances for liquid hydrogen infrastructure in fire codes the dispersion characteristics of cryogenic hydrogen jets (50–64 K) from high aspect ratio nozzles have been measured at 3 and 5 barabs stagnation pressures. These nozzles are more characteristic of unintended leaks which would be expected to be cracks rather than conventional round nozzles. Spontaneous Raman scattering was used to measure the concentration and temperature field along the major and minor axes. Within the field of interrogation the axis-switching phenomena was not observed but rather a self-similar Gaussian-profile flow regime similar to room temperature or cryogenic hydrogen releases through round nozzles. The concentration decay rate and half-widths for the planar cryogenic jets were found to be nominally equivalent to that of round nozzle cryogenic hydrogen jets indicating a similar flammable envelope. The results from these experiments will be used to validate models for cryogenic hydrogen dispersion that will be used for simulations of alternative scenarios and quantitative risk assessment
Secure, Affordable, Low Carbon: Gas in our Future Energy System
Feb 2020
Publication
Our gas network is one of the best developed in the world providing safe secure affordable energy to homes and businesses across the UK.<br/><br/>To meet the biggest energy challenge of our generation – making deep cuts to carbon emissions by 2050 – it needs to embrace new technology which builds on these strengths and delivers the integrated flexible network of the future. This briefing sets out how it is already doing that. Take a look at our Gas Futures Messages booklet attached.
Sustainability Assessment of Fuel Cell Buses in Public Transport
May 2018
Publication
Hydrogen fuel cell (H2FC) buses operating in every day public transport services around Europe are assessed for their sustainability against environmental economic and social criteria. As part of this assessment the buses are evaluated against diesel buses both in terms of sustainability and in terms of meeting real world requirements with respect to operational performance. The study concludes that H2FC buses meet operability and performance criteria and are sustainable environmentally when ‘green’ hydrogen is used. The economic sustainability of the buses in terms of affordability achieves parity with their fossil fuel equivalent by 2030 when the indirect costs to human health and climate change are included. Societal acceptance by those who worked with and used the buses supports the positive findings of earlier studies although satisfactory operability and performance are shown to be essential to positive attitudes. Influential policy makers expressed positive sentiments only if ‘green’ hydrogen is used and the affordability issues can be addressed. No “show-stopper” is identified that would prevent future generations from using H2FC buses in public transport on a broad scale due to damage to the environment or to other factors that impinge on quality of life.
The Effect of the Temperature and Moisture to the Permeation Properties of PEO-Based Membranes for Carbon-Dioxide Separation
Jun 2021
Publication
An increased demand for energy in recent decades has caused an increase in the emissions of combustion products among which carbon-dioxide is the most harmful. As carbon-dioxide induces negative environmental effects like global warming and the greenhouse effect a decrease of the carbon-dioxide emission has emerged as one of the most urgent tasks in engineering. In this work the possibility for the application of the polymer-based dense mixed matrix membranes for flue gas treatment was tested. The task was to test a potential decrease in the permeability and selectivity of a mixed-matrix membrane in the presence of moisture and at elevated temperature. Membranes are based on two different poly(ethylene oxide)-based polymers filled with two different zeolite powders (ITR and IWS). An additive of detergent type was added to improve the contact properties between the zeolite and polymer matrix. The measurements were performed at three different temperatures (30 60 and 90 °C) under wet conditions with partial pressure of the water equal to the vapor pressure of the water at the given temperature. The permeability of carbon-dioxide hydrogen nitrogen and oxygen was measured and the selectivity of the carbon-dioxide versus other gases was determined. Obtained results have shown that an increase of temperature and partial pressure of the vapor slightly increase both the selectivity and permeability of the synthesized membranes. It was also shown that the addition of the zeolite powder increases the permeability of carbon-dioxide while maintaining the selectivity compared to hydrogen oxygen and nitrogen.
HyDeploy Report: Gas Characteristics (Leakage, Dispersion and Flammability)
Sep 2018
Publication
The Health and Safety Laboratory (HSL) has carried out an investigation into the gas characteristics that may influence the leakage dispersion and flammability hazards associated with blended natural gas-hydrogen mixtures containing up to 20 % mol/mol hydrogen. The work was carried out under contract to Cadent & Northern Gas Networks as part of the HyDeploy project which was commissioned to investigate the feasibility of using blended hydrogen-natural gas mixtures in UK mains gas distribution networks.
Under the HyDeploy project a demonstration scheme is being carried out at Keele University in which it is planned to inject up to 20 % mol/mol hydrogen. Keele is Britain’s largest campus university and an ideal test site for a demonstration scheme as its gas distribution network is largely independent of the national gas network but still subject to UK gas industry procedural controls. It is anticipated that a successful demonstration scheme will facilitate the use of blended natural gas-hydrogen mixtures throughout the UK leading to significant reductions in carbon dioxide emissions. The project is being led by Cadent & Northern Gas Networks and also involves ITM Power Progressive Energy Keele University and HSL in consortium.
Click the supplements tab to view the other documents in this report
Under the HyDeploy project a demonstration scheme is being carried out at Keele University in which it is planned to inject up to 20 % mol/mol hydrogen. Keele is Britain’s largest campus university and an ideal test site for a demonstration scheme as its gas distribution network is largely independent of the national gas network but still subject to UK gas industry procedural controls. It is anticipated that a successful demonstration scheme will facilitate the use of blended natural gas-hydrogen mixtures throughout the UK leading to significant reductions in carbon dioxide emissions. The project is being led by Cadent & Northern Gas Networks and also involves ITM Power Progressive Energy Keele University and HSL in consortium.
Click the supplements tab to view the other documents in this report
Sustainable Hydrogen Production: A Role for Fusion
Apr 2007
Publication
This Meeting Report summarises the findings of a two-day workshop in April 2007 at the Culham Science Centre and Worcester College Oxford which explored the potential for large-scale Hydrogen production through methods other than electrolysis.<br/>Operating at the cusp of research and policy-making the UK Energy Research Centre's mission is to be the UK's pre-eminent centre of research and source of authoritative information and leadership on sustainable energy systems. The Centre takes a whole systems approach to energy research incorporating economics engineering and the physical environmental and social sciences while developing and maintaining the means to enable cohesive research in energy. A key supporting function of UKERC is the Meeting Place based in Oxford which aims to bring together members of the UK energy community and overseas experts from different disciplines to learn identify problems develop solutions and further the energy debate.
Charge Carrier Mapping for Z-scheme Photocatalytic Water-splitting Sheet via Categorization of Microscopic Time-resolved Image Sequences
Jun 2021
Publication
Photocatalytic water splitting system using particulate semiconductor materials is a promising strategy for converting solar energy into hydrogen and oxygen. In particular visible-light-driven ‘Z-scheme’ printable photocatalyst sheets are cost-effective and scalable. However little is known about the fundamental photophysical processes which are key to explaining and promoting the photoactivity. Here we applied the pattern-illumination time-resolved phase microscopy for a photocatalyst sheet composed of Mo-doped BiVO4 and Rh-doped SrTiO3 with indium tin oxide as the electron mediator to investigate photo-generated charge carrier dynamics. Using this method we successfully observed the position- and structure-dependent charge carrier behavior and visualized the active/inactive sites in the sheets under the light irradiation via the time sequence images and the clustering analysis. This combination methodology could provide the material/synthesis optimization methods for the maximum performance of the photocatalyst sheets.
Quantitative Risk Analysis of a Hazardous Jet Fire Event for Hydrogen Transport in Natural Gas Transmission Pipelines
Jan 2021
Publication
With the advent of large-scale application of hydrogen transportation becomes crucial. Reusing the existing natural gas transmission system could serve as catalyst for the future hydrogen economy. However a risk analysis of hydrogen transmission in existing pipelines is essential for the deployment of the new energy carrier. This paper focuses on the individual risk (IR) associated with a hazardous hydrogen jet fire and compares it with the natural gas case. The risk analysis adopts a detailed flame model and state of the art computational software to provide an enhanced physical description of flame characteristics.<br/>This analysis concludes that hydrogen jet fires yield lower lethality levels that decrease faster with distance than natural gas jet fires. Consequently for large pipelines hydrogen transmission is accompanied by significant lower IR. Howbeit ignition effects increasingly dominate the IR for decreasing pipeline diameters and cause hydrogen transmission to yield increased IR in the vicinity of the pipeline when compared to natural gas.
Brittle Fracture Manifestation in Gas Pipeline Steels after Long-term Operation
Dec 2020
Publication
Gas pipelines are exposed to operational loads combined with corrosive environment action during their long-term service. Complicated service conditions lead to a worsening of steel properties a reduction of serviceability of the whole object therefore a risk of its premature failure rises. Aware of the importance of the existing problem the aim of this study is the analysis of various mechanical properties of steels after their long-term operation on gas pipelines and detecting and evaluating fractographic signs of this degradation.<br/>Mechanical properties of operated pipe steels characterizing their brittle fracture resistance were significantly decreased. Delamination areas as one of a feature of brittle fracture were identified on the fracture surfaces of specimens after SSRT of the operated steels in corrosive environment. Fracture was initiated from the outer surface of the specimens along the boundaries of ferrite and pearlite grains with significant secondary cracking.<br/>The obvious texture in the steels affects noticeably the results of the impact tests. Higher KCV values for the specimens cut in the longitudinal direction relative to the pipe axis comparing with the specimens of transversal orientation were obtained. This was explained by different length of narrow pearlite strips alternated by wide ferrite bands and interrupted by individual ferrite grains depending on the orientation of the specimen fracture surface relative to the pipe axis. Thus a proper direction of specimen cutting to achieve the maximum sensitivity of KCV parameter to operational degradation of steels is discussed. The effect of specimen orientation on the results of the Charpy testing becomes much more pronounced with steel operation. Defects accumulated in steels during their service are preferentially oriented in the pipe axial direction along the boundaries between ferrite and pearlite strips. Analyzing the fracture surfaces of the Charpy specimens after their impact testing certain signs of embrittlement were found for long term operated steels in the form of delaminations varying in size and shape and some cleavage fragments. Furthermore their percentage of total fracture surface (generally formed by dimples) correlates well with a drop in the impact toughness. The established relationship could be the basis for the introduction of fractographic criteria of the steel serviceability.
On The Kinetics of Alh3 Decomposition and the Subsequent Al Oxidation
Sep 2011
Publication
Metal hydrides are used for hydrogen storage. AlH3 shows a capacity to store about 10 wt% hydrogen. Its hydrogen is split-off in the temperature interval of 400–500 K. On dehydrogenation a nano-structured Al material emerges with specific surfaces up to 15–20 m2/g. The surface areas depend on the heating rate because of a temperature dependent crystallite growth. The resulting Al oxidizes up to 20–25% weight on air access forming an alumina passivation layer of 3–4 nm thickness on all exposed surfaces. The heat released from this Al oxidation induces a high risk to this type of hydrogen storage if the containment might be destroyed accidentally. The kinetics of the dehydrogenation and the subsequent oxidation is investigated by methods of thermal analysis. A reaction scheme is confirmed which consists of a starting Avrami-Erofeev mechanism followed by formal 1st order oxidation on unlimited air access. The kinetic parameters activation energies and pre-exponentials are evaluated and can be used to calculate the reaction progress. Together with the heat of the Al oxidation the overall heat release and the related rate can be estimated.
New Integrated Process for the Efficient Production of Methanol, Electrical Power, and Heating
Jan 2022
Publication
In this paper a novel process is developed to cogenerate 4741 kg/h of methanol 297.7 kW of electricity and 35.73 ton/h of hot water including a hydrogen purification system an absorption– compression refrigeration cycle (ACRC) a regenerative Organic Rankine Cycle (ORC) and parabolic solar troughs. The heat produced in the methanol reactor is recovered in the ORC and ACRC. Parabolic solar troughs provide thermal power to the methanol distillation tower. Thermal efficiencies of the integrated structure and the liquid methanol production cycle are 78.14% and 60.91% respectively. The process’s total exergy efficiency and irreversibility are 89.45% and 16.89 MW. The solar thermal collectors take the largest share of exergy destruction (34%) followed by heat exchangers (30%) and mixers (19%). Based on the sensitivity analysis D17 (mixture of H2 and low-pressure fuel gas before separation) was the most influential stream affecting the performance of the process. With the temperature decline of stream D17 from −139 to −149 °C the methanol production rate and the total thermal efficiency rose to 4741.2 kg/h and 61.02% respectively. Moreover the growth in the hydrogen content from 55% to 80% molar of the feed gas the flow rate of liquid methanol and the total exergy efficiency declined to 4487 kg/h and 86.05%.
What is Needed to Deliver Carbon-neutral Heat Using Hydrogen and CCS?
Sep 2020
Publication
In comparison with the power sector large scale decarbonisation of heat has received relatively little attention at the infrastructural scale despite its importance in the global CO2 emissions landscape. In this study we focus on the regional transition of a heating sector from natural gas-based infrastructure to H2 using mathematical optimisation. A discrete spatio-temporal description of the geographical region of Great Britain was used in addition to a detailed description of all network elements for illustrating the key factors in the design of nation-wide H2 and CO2 infrastructure. We have found that the synergistic deployment of H2 production technologies such as autothermal reforming of methane and biomass gasification with CO2 abatement technologies such as carbon capture and storage (CCS) are critical in achieving cost-effective decarbonisation. We show that both large scale underground H2 storage and water electrolysis provide resilience and flexibility to the heating system competing on cost and deployment rates. The optimal regions for siting H2 production infrastructure are characterised by proximity to: (1) underground H2 storage (2) high demands for H2 (3) geological storage for CO2. Furthermore cost-effective transitions based on a methane reforming pathway may necessitate regional expansions in the supply of natural gas with profound implications for security of supply in nations that are already highly reliant potentially creating an infrastructure lock-in during the near term. We found that the total system cost comprising both investment and operational elements is mostly influenced by the natural gas price followed by biomass price and CapEx of underground caverns. Under a hybrid Regulated Asset Base (RAB) commercial framework with private enterprises delivering production infrastructure the total cost of heat supply over the infrastructure lifetime is estimated as 5.2–8.6 pence per kW h. Due to the higher cost relative to natural gas a Contract for Difference payment between d20 per MW h and d53 per MW h will be necessary for H2-derived heat to be competitive in the market.
Real World Hydrogen Technology Validation
Sep 2011
Publication
The Department of Energy the Department of Defense's Defense Logistics Agency and the Department of Transportation's Federal Transit Administration have funded learning demonstrations and early market deployments to provide insight into applications of hydrogen technologies on the road in the warehouse and as stationary power. NREL's analyses validate the technology in real-world applications reveal the status of the technology and facilitate the development of hydrogen and fuel cell technologies manufacturing and operations. This paper presents the maintenance safety and operation data of fuel cells in multiple applications with the reported incidents near misses and frequencies. NREL has analyzed records of more than 225000 kilograms of hydrogen that have been dispensed through more than 108000 hydrogen fills with an excellent safety record.
A New Approach to Vented Deflagration Modeling
Sep 2017
Publication
In the present work CFD simulations of a hydrogen deflagration experiment are performed. The experiment carried out by KIT was conducted in a 1 m3 enclosure with a square vent of 0.5 m2 located in the center of one of its walls. The enclosure was filled with homogeneous hydrogen-air mixture of 18% v/v before ignition at its back-wall. As the flame propagates away from the ignition point unburned mixture is forced out through the vent. This mixture is ignited when the flame passes through the vent initiating a violent external explosion which leads to a rapid increase in pressure. The work focuses on the modeling of the external explosion phenomenon. A new approach is proposed in order to predict with accuracy the strength of external explosions using Large Eddy Simulation. The new approach introduces new relations to account for the interaction between the turbulence and the flame front. CFD predictions of the pressure inside and outside the enclosure and of the flame front shape are compared against experimental measurements. The comparison indicates a much better performance of the new approach compared to the initial model.
Safety and Risk Management in Nuclear-Based Hydrogen Production with Thermal Water Splitting
Sep 2013
Publication
The challenges and approaches of the safety and risk management for the hydrogen production with nuclear-based thermochemical water splitting have been far from sufficiently reported as the thermochemical technology is still at a fledgling stage and the linkage of a nuclear reactor with a hydrogen production plant is unprecedented. This paper focuses on the safety issues arising from the interactions between the nuclear heat source and thermochemical hydrogen production cycle as well between the proximate individual processes in the cycle. As steam is utilized in most thermochemical cycles for the water splitting reaction and heat must be transferred from the nuclear source to hydrogen production plant this paper particularly analyzes and quantifies the heat hazard for the scenarios of start-up and shutdown of the hydrogen production plant. Potential safety impacts on the nuclear reactor are discussed. It is concluded that one of the main challenges of safety and risk management is efficient rejection of heat in a shutdown accident. Several options for the measures to be taken are suggested. Copper-chlorine and sulphur-iodine thermochemical cycles are taken as two representative examples for the hazard analysis. It is expected that these newly reported challenges and approaches could help build the future safety and risk management codes and standards for the infrastructure of the thermochemical hydrogen production.
Materials Towards Carbon-free, Emission-free and Oil-free Mobility: Hydrogen Fuel-cell Vehicles—Now and in the Future
Jul 2010
Publication
In the past material innovation has changed society through new material-induced technologies adding a new value to society. In the present world engineers and scientists are expected to invent new materials to solve the global problem of climate change. For the transport sector the challenge for material engineers is to change the oil-based world into a sustainable world. After witnessing the recent high oil price and its adverse impact on the global economy it is time to accelerate our efforts towards this change.
Industries are tackling global energy issues such as oil and CO2 as well as local environmental problems such as NOx and particulate matter. Hydrogen is the most promising candidate to provide carbon-free emission-free and oil-free mobility. As such engineers are working very hard to bring this technology into the real society. This paper describes recent progress of vehicle technologies as well as hydrogen-storage technologies to extend the cruise range and ensure the easiness of refuelling and requesting material scientists to collaborate with industry to fight against global warming.
Link to document download on Royal Society Website
Industries are tackling global energy issues such as oil and CO2 as well as local environmental problems such as NOx and particulate matter. Hydrogen is the most promising candidate to provide carbon-free emission-free and oil-free mobility. As such engineers are working very hard to bring this technology into the real society. This paper describes recent progress of vehicle technologies as well as hydrogen-storage technologies to extend the cruise range and ensure the easiness of refuelling and requesting material scientists to collaborate with industry to fight against global warming.
Link to document download on Royal Society Website
Boundary Layer Effects on the Critical Nozzle of Hydrogen Sonic Jet
Oct 2015
Publication
When hydrogen flows through a small finite length constant exit area nozzle the viscous effects create a fluid throat which acts as a converging-diverging nozzle and lead to Mach number greater than one at the exit if the jet is under-expanded. This phenomenon influences the mass flow rate and the dispersion cloud size. In this study the boundary layer effect on the unsteady hydrogen sonic jet flow through a 1 mm diameter pipe from a high pressure reservoir (up to 70 MPa) is studied using computational fluid dynamics with a large eddy simulation turbulence model. This viscous flow simulation is compared with a non-viscous simulation to demonstrate that the velocity is supersonic at the exit of a small exit nozzle and that the mass flow is reduced.
Clean Hydrogen Monitor
Oct 2020
Publication
It’s the first of its kind overview showing the state of play with regards to hydrogen technologies in Europe. On an annual basis there will be an update serving as a basis for your investment or political decisions.<br/><br/>OUR MISSION IS – NO EMISSION!<br/>From day 1 Hydrogen Europe promoted clean hydrogen and clean hydrogen technologies as enablers of a decarbonised energy system. We strongly support the adoption of very ambitious climate targets for 2030 and the objective of carbon neutrality in the EU by 2050. Clean hydrogen can help to realise this transition of our energy system in multiple sectors from energy production storage and distribution to end-uses in transport industry heating and others.<br/><br/>CLEAN HYDROGEN TECHNOLOGIES CAN AND WILL REPLACE<br/>not just fossil-based hydrogen in current (industrial) uses but also other fossil-based energies such as petrol diesel and hydrocarbon fuels in the transport sector coal /coke in the steel sector natural gas in the heating sector and other polluting and emitting fuels and feedstocks. <br/><br/>WE ARE TALKING ABOUT A SYSTEMIC CHANGE.<br/>The use of clean hydrogen needs adaptations in production schemes in the infrastructure and in the deployment of hydrogen by the end users. This cannot – of course –be done in a day. Yet we should not wait for the implementation of the different hydrogen strategies on private municipal regional national or European level until other geographies worldwide race ahead.<br/><br/>
Evaluation of Hydrogen, Propane and Methane-air Detonations Instability and Detonability
Sep 2013
Publication
In this paper the detonation propensity of different compositions of mixtures of hydrogen propane and methane with air has been evaluated over a wide range of compositions. We supplement the conventional calculations of the induction delay with calculations of the characteristic acceleration parameter recently suggested by Radulescu Sharpeand Bradley(RSB) to characterize the instability of detonations. While it is well established that the ignition delay provides a good measure for detonability the RSB acceleration or its non-dimensionalform provides a further discriminant between mixtures with similar ignition delays. The present assessment of detonability reveals that while a stoichiometric mixture of hydrogen-air has an ignition delay one and two orders of magnitude shorter than respectively propane and methane hydrogen also has a parameter smaller by respectively one and two orders of magnitude. Its smaller propensity for instability is reflected by an RSB acceleration parameter similar to the two hydrocarbons. The predictions however indicate that lean hydrogen mixtures are likely to be much more unstable than stoichiometric ones. The relation between the parameter and potential to amplify an unstable transverse wave structure has been further determined through numerical simulation of decaying reactive Taylor-Sedov blast waves. Using a simplified two-step model calibrated for these fuels we show that methane mixtures develop cellular structures more readily than propane and hydrogen when observed on similar induction time scales. Future work should be devoted towards a quantitative inclusion of the RSB parameter in assessing the detonability of a given mixture.
Hydrogen: The Future Energy Carrier
Jul 2010
Publication
Since the beginning of the twenty-first century the limitations of the fossil age with regard to the continuing growth of energy demand the peaking mining rate of oil the growing impact of CO2 emissions on the environment and the dependency of the economy in the industrialized world on the availability of fossil fuels became very obvious. A major change in the energy economy from fossil energy carriers to renewable energy fluxes is necessary. The main challenge is to efficiently convert renewable energy into electricity and the storage of electricity or the production of a synthetic fuel. Hydrogen is produced from water by electricity through an electrolyser. The storage of hydrogen in its molecular or atomic form is a materials challenge. Some hydrides are known to exhibit a hydrogen density comparable to oil; however these hydrides require a sophisticated storage system. The system energy density is significantly smaller than the energy density of fossil fuels. An interesting alternative to the direct storage of hydrogen are synthetic hydrocarbons produced from hydrogen and CO2 extracted from the atmosphere. They are CO2 neutral and stored like fossil fuels. Conventional combustion engines and turbines can be used in order to convert the stored energy into work and heat.
Link to document download on Royal Society Website
Link to document download on Royal Society Website
Polymer Electrolyte Membrane Fuel Cell and Hydrogen Station Networks for Automobiles: Status, Technology, and Perspectives
Feb 2021
Publication
The U.S. transportation sector accounts for 37% of total energy consumption. Automobiles are a primary application of polymer electrolyte membrane (PEM) fuel cells which operate under low temperature and high efficiency to reduce fossil fuel consumption and CO2 emissions. Using hydrogen fuel PEM fuel cells can reach a practical efficiency as high as 65% with water as the only byproduct. Almost all the major automakers are involved in fuel cell electric vehicle (FCEV) development. Toyota and Hyundai introduced FCEVs (the Mirai and NEXO respectively) to consumers in recent years with a driving range between 312 and 402 miles and cold-start capacity from -30 °C. About 50 fuel cell electric buses (FCEB) are operating in California and most of them have achieved the durability target i.e. 25000 h in real-world driving conditions. As of September 2020 over 8573 FCEVs have been sold or leased in the U.S. More than 3521 FCEVs and 22 FCEBs have been sold or leased in Japan as of September 2019. An extensive hydrogen station network is required for the successful deployment of FCEVs and FCEBs. The U.S. currently has over 44 hydrogen fuelling stations (HFSs) nearly all located in California. Europe has over 139 HFSs with ~1500 more stations planned by 2025. This review has three primary objectives: 1) to present the current status of FCEV/FCEB commercialization and HFS development; 2) to describe the PEM fuel cell research/development in automobile applications and the significance of HFS networks; and 3) to outline major challenges and opportunities.
Hydrogen Production from Natural Gas and Biomethane with Carbon Capture and Storage – A Techno-environmental Analysis
Mar 2020
Publication
This study presents an integrated techno-environmental assessment of hydrogen production from natural gas and biomethane combined with CO2 capture and storage (CCS). We have included steam methane reforming (SMR) and autothermal reforming (ATR) for syngas production. CO2 is captured from the syngas with a novel vacuum pressure swing adsorption (VPSA) process that combines hydrogen purification and CO2 separation in one cycle. As comparison we have included cases with conventional amine-based technology. We have extended standard attributional Life Cycle Assessment (LCA) following ISO standards with a detailed carbon balance of the biogas production process (via digestion) and its by-products. The results show that the life-cycle greenhouse gas (GHG) performance of the VPSA and amine-based CO2 capture technologies is very similar as a result of comparable energy consumption. The configuration with the highest plant-wide CO2 capture rate (almost 100% of produced CO2 captured) is autothermal reforming with a two-stage water-gas shift and VPSA CO2 capture – because the latter has an inherently high CO2 capture rate of 98% or more for the investigated syngas. Depending on the configuration the addition of CCS to natural gas reforming-based hydrogen production reduces its life-cycle Global Warming Potential by 45–85 percent while the other environmental life-cycle impacts slightly increase. This brings natural gas-based hydrogen on par with renewable electricity-based hydrogen regarding impacts on climate change. When biomethane is used instead of natural gas our study shows potential for net negative greenhouse gas emissions i.e. the net removal of CO2 over the life cycle of biowaste-based hydrogen production. In the special case where the biogas digestate is used as agricultural fertiliser and where a substantial amount of the carbon in the digestate remains in the soil the biowaste-based hydrogen reaches net-negative life cycle greenhouse gas emissions even without the application of CCS. Addition of CCS to biomethane-based hydrogen production leads to net-negative emissions in all investigated cases.
Sizing and Operation of a Pure Renewable Energy Based Electric System through Hydrogen
Nov 2021
Publication
Today in order to reduce the increase of the carbon dioxide emissions a large number of renewable energy resources (RES) are already implemented. Considering both the intermittency and uncertainty of the RES the energy storage system (ESS) is still needed for balancing and stabilizing the power system. Among different existing categories of ESS the hydrogen storage systems (HSS) have the highest energy density and are crucial for the RES integration. In addition RES are located in faraway regions and are often transmitted to the terminal consumption center through HVDC (high voltage direct current) due to its lower power loss. In this paper we present a power supply system that achieves low-carbon emissions through combined HSS and HVDC technology. First the combined HSS and the HVDC model are established. Secondly the rule-based strategy for operating the HSS microgrid is presented. Then an operating strategy for a typical network i.e. the pure RES generation station-HVDC transmission-microgrids is demonstrated. Finally the best sizing capacities for all components are found by the genetic algorithm. The results prove the efficiency of the presented sizing approach for a pure RES electric system.
Simulation of the Combustion Process for a CI Hydrogen Engine in an Argon-oxygen Atmosphere
May 2018
Publication
Hydrogen combustion in a noble gas atmosphere increases the combustion chamber temperature and the high specific heat ratio of the gas increases the thermal efficiency. In this study nitrogen was replaced by argon as the intake air along with pure oxygen to supply the engine. The objectives of this study are to determine the effects of different engine parameters on combustion and to analyse the emissions from hydrogen combustion in an argon-oxygen atmosphere. This research was conducted through simulations using CONVERGE 2.2.0 software and the YANMAR engine NF19SK model was used to determine the basic parameters. Changing the injector location affects the pressure and temperature in the combustion chamber. With increasing compression ratio the pressure increases more rapidly than the temperature. However combustion at high compression ratios decreases the maximum heat release rate and increases the combustion duration. Hydrogen combustion at ambient temperatures below 1200 K follows the Arrhenius equation.
The Ten Point Plan for a Green Industrial Revolution: Building Back Better, Supporting Green Jobs, and Accelerating Our Path to Net Zero
Nov 2020
Publication
As the world looks to recover from the impact of coronavirus on our lives livelihoods and economies we have the chance to build back better: to invest in making the UK a global leader in green technologies.
The plan focuses on increasing ambition in the following areas:
The plan focuses on increasing ambition in the following areas:
- advancing offshore wind
- driving the growth of low carbon hydrogen
- delivering new and advanced nuclear power
- accelerating the shift to zero emission vehicles
- green public transport cycling and walking
- ‘jet zero’ and green ships
- greener buildings
- investing in carbon capture usage and storage
- protecting our natural environment
- green finance and innovation
Rock Mass Response for Lined Rock Caverns Subjected to High Internal Gas Pressure
Mar 2022
Publication
The storage of hydrogen gas in underground lined rock caverns (LRCs) enables the implementation of the first fossil-free steelmaking process to meet the large demand for crude steel. Predicting the response of rock mass is important to ensure that gas leakage due to rupture of the steel lining does not occur. Analytical and numerical models can be used to estimate the rock mass response to high internal pressure; however the fitness of these models under different in situ stress conditions and cavern shapes has not been studied. In this paper the suitability of analytical and numerical models to estimate the maximum cavern wall tangential strain under high internal pressure is studied. The analytical model is derived in detail and finite element (FE) models considering both two-dimensional (2D) and three-dimensional (3D) geometries are presented. These models are verified with field measurements from the LRC in Skallen southwestern Sweden. The analytical model is inexpensive to implement and gives good results for isotropic in situ stress conditions and large cavern heights. For the case of anisotropic horizontal in situ stresses as the conditions in Skallen the 3D FE model is the best approach
Investigation of Hydrogen Embrittlement Susceptibility and Fracture Toughness Drop after in situ Hydrogen Cathodic Charging for an X65 Pipeline Steel
Apr 2020
Publication
The present research focuses on the investigation of an in situ hydrogen charging effect during Crack Tip Opening Displacement testing (CTOD) on the fracture toughness properties of X65 pipeline steel. This grade of steel belongs to the broader category of High Strength Low Alloy Steels (HSLA) and its microstructure consists of equiaxed ferritic and bainitic grains with a low volume fraction of degenerated pearlite islands. The studied X65 steel specimens were extracted from pipes with 19.15 mm wall thickness. The fracture toughness parameters were determined after imposing the fatigue pre-cracked specimens on air on a specific electrolytic cell under a slow strain rate bending loading (according to ASTM G147-98 BS7448 and ISO12135 standards). Concerning the results of this study in the first phase the hydrogen cations’ penetration depth the diffusion coefficient of molecular and atomic hydrogen and the surficial density of blisters were determined. Next the characteristic parameters related to fracture toughness (such as J KQ CTODel CTODpl) were calculated by the aid of the Force-Crack Mouth Open Displacement curves and the relevant analytical equations.
Hydrogen Storage: Recent Improvements and Industrial Perspectives
Sep 2017
Publication
Efficient storage of hydrogen is crucial for the success of hydrogen energy markets (early markets as well as transportation market). Hydrogen can be stored either as a compressed gas a refrigerated liquefied gas a cryo-compressed gas or in hydrides. This paper gives an overview of hydrogen storage technologies and details the specific issues and constraints related to the materials behaviour in hydrogen and conditions representative of hydrogen energy uses. It is indeed essential for the development of applications requiring long-term performance to have good understanding of long-term behaviour of the materials of the storage device and its components under operational loads.
World Energy Issues Monitor 2021: Humanising Energy
Mar 2021
Publication
Based on data collection carried out between October and December 2020 and the testing of emerging findings with the Council’s regional communities during a series of digital workshops held during February 2021 the report has shown
- Energy leaders’ perceptions of areas of risk opportunity and priorities for action have radically changed over the last 12 months. While economic turbulence stemming from the ongoing reverberations of COVID-19 is the biggest area of uncertainty with uncertainty around economic trends increasing by a third over the previous year there is also a growing focus on the social agenda associated with a faster paced energy transition.
- There is an increased awareness of the societal and human impact of both recovery and the wider energy transition. The issue of energy affordability has rapidly risen up the industry’s priority list with its impact and uncertainty perceived 20% larger than a year ago. Energy affordability affects society across all geographies ranging from city dwellers in developed countries to the rural poor in developing ones.
- The emergence of a new generation of digital energy services and energy entrepreneurs. Increasingly agile disruptive technologies have taken advantage of the social upheaval to gain market share at the expense of supply-centric energy solutions. There is a growing focus on customer-centric demand-driven solutions and fast changing patterns of global and local demand.
Pd Catalysts Supported on Bamboo-Like Nitrogen-Doped Carbon Nanotubes for Hydrogen Production
Mar 2021
Publication
Bamboo-like nitrogen-doped carbon nanotubes (N-CNTs) were used to synthesize supported palladium catalysts (0.2–2 wt.%) for hydrogen production via gas phase formic acid decomposition. The beneficial role of nitrogen centers of N-CNTs in the formation of active isolated palladium ions and dispersed palladium nanoparticles was demonstrated. It was shown that although the surface layers of N-CNTs are enriched with graphitic nitrogen palladium first interacts with accessible pyridinic centers of N-CNTs to form stable isolated palladium ions. The activity of Pd/N-CNTs catalysts is determined by the ionic capacity of N-CNTs and dispersion of metallic nanoparticles stabilized on the nitrogen centers. The maximum activity was observed for the 0.2% Pd/N-CNTs catalyst consisting of isolated palladium ions. A ten-fold increase in the concentration of supported palladium increased the contribution of metallic nanoparticles with a mean size of 1.3 nm and decreased the reaction rate by only a factor of 1.4.
Design of Experiment to Predict the Time Between Hydrogen Purges for an Air-breathing PEM Fuel Cell in Dead-end Mode in a Closed Environment
Feb 2021
Publication
Fuel cells are promising technologies for zero-emission energy conversion. They are used in several applications such as power plants cars and even submarines. Hydrogen supply is crucial for such systems and using Proton Exchange Membrane Fuel Cell in dead-end mode is a solution to save hydrogen. Since water and impurities accumulate inside the stack purging is necessary. However the importance of operating parameters is not well known for fuel cells working in closed environments. A Design of Experiment approach studying time between two purges and cell performance was conducted on an air-breathing stack in a closed environment. The most influential parameters on the time between two purges are the relative humidity and the current load. Convection in the closed environment can decrease the stability of the fuel cell. A linear model with interactions between these last three parameters was found to accurately describe the studied responses.
Global Energy Transformation: A Roadmap to 2050
Apr 2019
Publication
Dolf Gielen,
Ricardo Gorini,
Nicholas Wagner,
Rodrigo Leme,
Laura Gutierrez,
Gayathri Prakash,
Elisa Asmelash,
Luis Janeiro,
Giacomo Gallina,
Guilia Vale,
Lorenzo Sani,
Xavier Garcia Casals,
Rabia Ferroukhi,
Bishal Parajuli,
Jinlei Feng,
Eva Alexandri,
Unnada Chewpreecha,
Mary Goldman,
Sophie Heald,
Jon Stenning,
Hector Pollitt,
Celia García-Baños and
Michael Renner
Increased use of renewable energy combined with intensified electrification could prove decisive for the world to meet key climate goals by 2050. This study from the International Renewable Energy Agency (IRENA) highlights immediately deployable cost-effective options for countries to fulfil climate commitments and limit the rise of global temperatures. The envisaged energy transformation would also reduce net costs and bring significant socio-economic benefits such as increased economic growth job creation and overall welfare gains.<br/>The report – the second under the Global Energy Transformation banner – expands IRENA’s comprehensive roadmap which examines technology pathways and policy implications to ensure a sustainable energy future. Ramping up electricity to over half of the global energy mix (up from one-fifth currently) in combination with renewables would reduce the use of fossil fuels responsible for most greenhouse-gas emissions.
The Influence of Refractory Metals on the Hydrogen Storage Characteristics of FeTi-based Alloys Prepared by Suspended Droplet Alloying
Jun 2020
Publication
The influence of the addition of refractory metals (molybdenum and tantalum) on the hydrogenation properties of FeTi intermetallic phase-based alloys was investigated. The suspended droplet alloying technique was applied to fabricate FeTiTa-based and FeTiMo-based alloys. The phase composition and hydrogen storage properties of the samples were investigated. The samples modified with the refractory metals exhibited lower plateau pressures and lower hydrogen storage capacities than those of the FeTi reference sample due to solid solution formation. It was observed that the equilibrium pressures decreased with the amount of molybdenum which is in good agreement with the increase in the cell parameters of the TiFe phase. Suspended droplet alloying was found to be a practical method to fabricate alloys with refractory metal additions; however it is appropriate for screening samples with desired chemical and phase compositions rather than for manufacturing purposes.
Study on Hydrogen from Renewable Resources in the EU
Feb 2016
Publication
Hydrogen can be produced from a broad range of renewable energy sources acting as a unique energy hub providing low or zero emission energy to all energy consuming sectors. Technically and efficiently producing hydrogen from renewable sources is a key enabler for these developments.<br/>Traditionally hydrogen has been produced from fossil sources by steam methane reforming of natural gas. At present the technology of choice to produce renewable ‘green’ hydrogen is water electrolysis using renewable electricity. The FCH JU has been supporting research and development of electrolyser technology and application projects aiming to increase the energy efficiency of electrolytic hydrogen production from renewable sources and to reduce costs.<br/>This study complements these activities by focusing on renewable hydrogen generation other than electrolysis. In this report these alternative hydrogen generation technologies are described characterized by their technical capabilities maturity and economic performance and assessed for their future potential.<br/>A methodology has been devised to first identify and structure a set of relevant green hydrogen pathways (eleven pathways depicted in the figure below) analyse them at a level of detail allowing a selection of those technologies which fit into and promise early commercialization in the framework of FCH 2 JU’s funding program.<br/>These originally proposed eleven pathways use solar thermal energy sunlight or biomass as major energy input.
Potential for Hydrogen Production from Sustainable Biomass with Carbon Capture and Storage
Jan 2022
Publication
Low-carbon hydrogen is an essential element in the transition to net-zero emissions by 2050. Hydrogen production from biomass is a promising bio-energy with carbon capture and storage (BECCS) scheme that could produce low-carbon hydrogen and generate the carbon dioxide removal (CDR) envisioned to be required to offset hard-to-abate emissions. Here we design a BECCS supply chain for hydrogen production from biomass with carbon capture and storage and quantify at high spatial resolution the technical potential for hydrogen production and CDR in Europe. We consider sustainable biomass feedstocks that have minimal impacts on food security and biodiversity namely agricultural residues and waste. We find that this BECCS supply chain can produce up to 12.5 Mtons of H2 per year (currently ~10 Mtons of H2 per year are used in Europe) and remove up to 133 Mtons CO2 per year from the atmosphere (or 3% of European total greenhouse gas emissions). We then perform a geospatial analysis to quantify transportation distances between where biomass feedstocks are located and potential hydrogen users and find that 20% of hydrogen potential is located within 25 km from hard-toelectrify industries. We conclude that BECCS supply chains for hydrogen production from biomass represent an overlooked near-term opportunity to generate carbon dioxide removal and low-carbon hydrogen.
Hydrogen-air Vented Explosions- New Experimental Data
Sep 2013
Publication
The use of hydrogen as an energy carrier is a real perspective in Europe since a number of breakthroughs obtained in the last decades open the possibility to envision a deployment at the industrial scale if safety issues are duly accounted. However on this particular aspects experimental data are still lacking especially about the explosion dynamics in realistic dimensions. The purpose of this paper is to provide a set of totally new and well instrumented hydrogen - air vented explosions. Experiments were performed in a large explosion chamber within the scope of the DIMITRHY project (sponsored by the National French Agency for Research). The 4 m3 rectangular experimental chamber (2 m height 2 m width and 1 m depth) is equipped with transparent walls and is vented (0.25 and 0.5 m2 square vents).. Six pressure gauges were used to measure the overpressure evolution inside and outside the chamber. Six concentration gauges were used to control the hydrogen repartition in the vessel. The hydrogen-air cloud was seeded with micro particles of ammonium chloride to see the propagation of the flame the movement of the cloud inside and outside the chamber. The incidence of reactivity vent size ignition position and non homogenous repartition of hydrogen received a particular attention.
No more items...