- Home
- A-Z Publications
- Publications
Publications
Assessment of the Co-combustion Process of Ammonia with Hydrogen in a Research VCR Piston Engine
Oct 2022
Publication
The presented work concerns experimental research of a spark-ignition engine with variable compression ratio (VCR) adapted to dual-fuel operation in which co-combustion of ammonia with hydrogen was conducted and the energy share of hydrogen varied from 0% to 70%. The research was aimed at assessing the impact of the energy share of hydrogen co-combusted with ammonia on the performance stability and emissions of an engine operating at a compression ratio of 8 (CR 8) and 10 (CR 10). The operation of the engine powered by ammonia alone for both CR 8 and CR 10 is associated with either a complete lack of ignition in a significant number of cycles or with significantly delayed ignition and the related low value of the maximum pressure pmax. Increasing the energy share of hydrogen in the fuel to 12% allows to completely eliminate the instability of the ignition process in the combustible mixture which is confirmed by a decrease in the IMEP uniqueness and a much lower pmax dispersion. For 12% of the energy share of hydrogen co-combusted with ammonia the most favorable course of the combustion process was obtained the highest engine efficiency and the highest IMEP value were recorded. The conducted research shows that increasing the H2 share causes an increase in NO emissions for both analyzed compression ratios
Lessons Learned and Recommendations from Analysis of Hydrogen Incidents and Accidents to Support Risk Assessment for the Hydrogen Economy
Feb 2024
Publication
This study addresses challenges associated with hydrogen’s physio-chemical characteristics and the need for safety and public acceptance as a precursor to the emerging hydrogen economy. It highlights the gap in existing literature regarding lessons learned from events in the green hydrogen production value chain. The study aims to use the documented lessons learned from previous hydrogen-related events to assist in enhancing safety measures and to guide stakeholders on how to avoid and mitigate future hydrogen-related events. Given the potential catastrophic consequences robust safety systems are essential for hydrogen economy development. The work underscores the importance of human and operational factors as root causes of these events. The paper recommends establishing a specialized hydrogen-related event database to support risk assessment and risk mitigation thus catering to the growing hydrogen industry’s needs and facilitating quick access to critical information for stakeholders in the private and public sectors.
Adaptive Network Fuzzy Inference System and Particle Swarm Optimization of Biohydrogen Production Process
Sep 2022
Publication
Green hydrogen is considered to be one of the best candidates for fossil fuels in the near future. Bio-hydrogen production from the dark fermentation of organic materials including organic wastes is one of the most cost-effective and promising methods for hydrogen production. One of the main challenges posed by this method is the low production rate. Therefore optimizing the operating parameters such as the initial pH value operating temperature N/C ratio and organic concentration (xylose) plays a significant role in determining the hydrogen production rate. The experimental optimization of such parameters is complex expensive and lengthy. The present research used an experimental data asset adaptive network fuzzy inference system (ANFIS) modeling and particle swarm optimization to model and optimize hydrogen production. The coupling between ANFIS and PSO demonstrated a robust effect which was evident through the improvement in the hydrogen production based on the four input parameters. The results were compared with the experimental and RSM optimization models. The proposed method demonstrated an increase in the biohydrogen production of 100 mL/L compared to the experimental results and a 200 mL/L increase compared to the results obtained using ANOVA.
Modern Hydrogen Technologies in the Face of Climate Change—Analysis of Strategy and Development in Polish Conditions
Aug 2023
Publication
The energy production market based on hydrogen technologies is an innovative solution that will allow the industry to achieve climate neutrality in the future in Poland and in the world. The paper presents the idea of using hydrogen as a modern energy carrier and devices that in cooperation with renewable energy sources produce the so-called green hydrogen and the applicable legal acts that allow for the implementation of the new technology were analyzed. Energy transformation is inevitable and according to reports on good practices in European Union countries hydrogen and the hydrogen value chain (production transport and transmission storage use in transport and energy) have wide potential. Thanks to joint projects and subsidies from the EU initiatives supporting hydrogen technologies are created such as hydrogen clusters and hydrogen valleys and EU and national strategic programs set the main goals. Poland is one of the leaders in hydrogen production both in the world and in Europe. Domestic tycoons from the energy refining and chemical industries are involved in the projects. Eight hydrogen valleys that have recently been created in Poland successfully implement the assumptions of the “Polish Hydrogen Strategy until 2030 with a perspective until 2040” and “Energy Policy of Poland until 2040” which are in line with the assumptions of the most important legal acts of the EU including the European Union’s energy and climate policy the Green Deal and the Fit for 55 Package. The review of the analysis of the development of hydrogen technologies in Poland shows that Poland does not differ from other European countries. As part of the assumptions of the European Hydrogen Strategy and the trend related to the management of energy surpluses electrolyzers with a capacity of at least 6 GW will be installed in Poland in 2020–2024. It is also assumed that in the next phase planned for 2025–2030 hydrogen will be a carrier in the energy system in Poland. Poland as a member of the EU is the creator of documents that take into account the assumptions of the European Union Commission and systematically implement the assumed goals. The strategy of activities supporting the development of hydrogen technologies in Poland and the value chain includes very extensive activities related to among others obtaining hydrogen using hydrogen in transport energy and industry developing human resources for the new economy supporting the activities of hydrogen valley stakeholders building hydrogen refueling stations and cooperation among Poland Slovakia and the Czech Republic as part of the HydrogenEagle project.
Numerical Analysis of Dual Fuel Combustion in a Medium Speed Marine Engine Supplied with Methane/Hydrogen Blends
Sep 2023
Publication
Compression ignition engines will still be predominant in the naval sector: their high efficiency high torque and heavy weight perfectly suit the demands and architecture of ships. Nevertheless recent emission legislations impose limitations to the pollutant emissions levels in this sector as well. In addition to post-treatment systems it is necessary to reduce some pollutant species and therefore the study of combustion strategies and new fuels can represent valid paths for limiting environmental harmful emissions such as CO2 . The use of methane in dual fuel mode has already been implemented on existent vessels but the progressive decarbonization will lead to the utilization of carbon-neutral or carbon-free fuels such as in the last case hydrogen. Thanks to its high reactivity nature it can be helpful in the reduction of exhaust CH4 . On the contrary together with the high temperatures achieved by its oxidation hydrogen could cause uncontrolled ignition of the premixed charge and high emissions of NOx. As a matter of fact a source of ignition is still necessary to have better control on the whole combustion development. To this end an optimal and specific injection strategy can help to overcome all the before-mentioned issues. In this study three-dimensional numerical simulations have been performed with the ANSYS Forte® software (version 19.2) in an 8.8 L dual fuel engine cylinder supplied with methane hydrogen or hydrogen–methane blends with reference to experimental tests from the literature. A new kinetic mechanism has been used for the description of diesel fuel surrogate oxidation with a set of reactions specifically addressed for the low temperatures together with the GRIMECH 3.0 for CH4 and H2 . This kinetics scheme allowed for the adequate reproduction of the ignition timing for the various mixtures used. Preliminary calculations with a one-dimensional commercial code were performed to retrieve the initial conditions of CFD calculations in the cylinder. The used approach demonstrated to be quite a reliable tool to predict the performance of a marine engine working under dual fuel mode with hydrogen-based blends at medium load. As a result the system modelling shows that using hydrogen as fuel in the engine can achieve the same performance as diesel/natural gas but when hydrogen totally replaces methane CO2 is decreased up to 54% at the expense of the increase of about 76% of NOx emissions.
Optimal Scheduling of Power Systems with High Proportions of Renewable Energy Accounting for Operational Flexibility
Jul 2023
Publication
Yi Lin,
Wei Lin,
Wei Wu and
Zhenshan Zhu
The volatility and uncertainty of high-penetration renewable energy pose significant challenges to the stability of the power system. Current research often fails to consider the insufficient system flexibility during real-time scheduling. To address this issue this paper proposes a flexibility scheduling method for high-penetration renewable energy power systems that considers flexibility index constraints. Firstly a quantification method for flexibility resources and demands is introduced. Then considering the constraint of the flexibility margin index optimization scheduling strategies for different time scales including day-ahead scheduling and intra-day scheduling are developed with the objective of minimizing total operational costs. The intra-day optimization is divided into 15 min and 1 min time scales to meet the flexibility requirements of different time scales in the power system. Finally through simulation studies the proposed strategy is validated to enhance the system’s flexibility and economic performance. The daily operating costs are reduced by 3.1% and the wind curtailment rate is reduced by 4.7%. The proposed strategy not only considers the economic efficiency of day-ahead scheduling but also ensures a sufficient margin to cope with the uncertainty of intra-day renewable energy fluctuations.
Capacity Configuration Optimization for Green Hydrogen Generation by Solar-wind Hybrid Power Based on Comprehensive Performance Criteria
Aug 2023
Publication
Green hydrogen generation driven by solar-wind hybrid power is a key strategy for obtaining the low-carbon energy while by considering the fluctuation natures of solar-wind energy resource the system capacity configuration of power generation hydrogen production and essential storage devices need to be comprehensively optimized. In this work a solar-wind hybrid green hydrogen production system is developed by combining the hydrogen storage equipment with the power grid the coordinated operation strategy of solar-wind hybrid hydrogen production is proposed furthermore the NSGA-III algorithm is used to optimize the system capacity configuration with the comprehensive performance criteria of economy environment and energy efficiency. Through the implemented case study with the hydrogen production capacity of 20000 tons/year the abandoned energy power rate will be reduced to 3.32% with the electrolytic cell average load factor of 64.77% and the system achieves the remarkable carbon emission reduction. In addition with the advantage of connect to the power grid the generated surplus solar/wind power can be readily transmitted with addition income when the sale price of produced hydrogen is suggested to 27.80 CNY/kgH2 the internal rate of return of the system reaches to 8% which present the reasonable economic potential. The research provides technical and methodological suggestions and guidance for the development of solar-wind hybrid hydrogen production schemes with favorable comprehensive performance.
Development of a Hydrogen Supplement for use with IGEM/SR/25
Nov 2022
Publication
In response to the UK Government’s commitment to achieve net-zero carbon emissions by 2050 a range of research and demonstration projects are underway to investigate the feasibility of using hydrogen in place of natural gas within the national transmission and distribution system. In order for these projects to achieve their full scope of work a mechanism for performing hazardous area classification for hydrogen installations is required. At present IGEM/SR/25 is used to undertake such assessments for natural gas installations but the standard is not currently applicable to hydrogen or hydrogen/natural gas blends.<br/>This report presents updated data and a summary of the recommended methodologies for hazardous area classification of installations using hydrogen or blends of up to 20% hydrogen in natural gas. The contents of this report are intended to provide a technical commentary and the data for a hydrogen-specific supplement to IGEM/SR/25. The supplement will specifically cover 100% hydrogen and a 20/80% by volume blend of hydrogen/natural gas. Reference to intermediate blends is included in this report where appropriate to cover the anticipated step-wise introduction of hydrogen into the natural gas network.<br/>This report is divided into a series of appendices each of which covers a specific area of the IGEM standard. Each appendix includes a summary of specific recommendations made to enable IGEM/SR/25 to be applied to hydrogen and blends of up to 20% hydrogen in natural gas. The reader is encouraged to review the individual appendices for specific conclusions associated with the topic areas addressed in this report.<br/>In general the existing methodologies and approaches used for area classification in IGEM/SR/25 have been deemed appropriate for installations using either hydrogen or blends of up to 20% hydrogen in natural gas. Where necessary revised versions of the equations and zoning distances used in the standard are presented which account for the influence of material property differences between natural gas and the two alternative fuels considered in this work.
Carbon-negative Hydrogen: Exploring the Techno-economic Potential of Biomass Co-gasification with CO2 Capture
Sep 2021
Publication
The hydrogen economy is receiving increasing attention as a complement to electrification in the global energy transition. Clean hydrogen production is often viewed as a competition between natural gas reforming with CO2 capture and electrolysis using renewable electricity. However solid fuel gasification with CO2 capture presents another viable alternative especially when considering the potential of biomass to achieve negative CO2 emissions. This study investigates the techno-economic potential of hydrogen production from large-scale coal/ biomass co-gasification plants with CO2 capture. With a CO2 price of 50 €/ton the benchmark plant using commercially available technologies achieved an attractive hydrogen production cost of 1.78 €/kg with higher CO2 prices leading to considerable cost reductions. Advanced configurations employing hot gas clean-up membrane-assisted water-gas shift and more efficient gasification with slurry vaporization and a chemical quench reduced the hydrogen production cost to 1.50–1.62 €/kg with up to 100% CO2 capture. Without contingencies added to the pre-commercial technologies the lowest cost reduces to 1.43 €/kg. It was also possible to recover waste heat in the form of hot water at 120 ◦C for district heating potentially unlocking further cost reductions to 1.24 €/kg. In conclusion gasification of locally available solid fuels should be seriously considered next to natural gas and electrolysis for supplying the emerging hydrogen economy.
Decarbonisation of Heat and the Role of ‘Green Gas’ in the United Kingdom
May 2018
Publication
This paper looks at the possible role of ‘green gas’ in the decarbonisation of heat in the United Kingdom. The option is under active discussion at the moment because of the UK’s rigorous carbon reduction targets and the growing realisation that there are problems with the ‘default’ option of electrifying heat. Green gas appears to be technically and economically feasible. However as the paper discusses there are major practical and policy obstacles which make it unlikely that the government will commit itself to developing ‘green gas’ in the foreseeable future.
Green Hydrogen Production: Integrating Environmental and Social Criteria to Ensure Sustainability
Jul 2023
Publication
Hydrogen is experiencing an unprecedented global hype. Hydrogen is globally discussed as a possible future energy carrier and regarded as the urgently needed building block for the much needed carbon-neutral energy transition of hard-to-abate sectors to mitigate the effects of global warming. This article provides synthesised measurable sustainability criteria for analysing green hydrogen production proposals and strategies. Drawn from expert interviews and an extensive literature review this article proposes that a sustainable hydrogen production should consider six impact categories; Energy transition Environment Basic needs Socio-economy Electricity supply and Project planning. The categories are broken down into sixteen measurable sustainability criteria which are determined with related indicators. The article concludes that low economic costs can never be the only decisive criterion for the hydrogen production; social aspects must be integrated along the entire value chain. The compliance with the criteria may avoid social and ecological injustices in the planning of green hydrogen projects and increases inter alia the social welfare of the affected population.
Performance Evaluation of a Fuel Cell mCHP System under Different Configurations of Hydrogen Origin and Heat Recovery
Sep 2023
Publication
Motivated by the growing importance of fuel cell systems as the basis for distributed energy generation systems this work considers a micro-combined heat and power (mCHP) generation system based on a fuel cell integrated to satisfy the (power and thermal) energy demands of a residential application. The main objective of this work is to compare the performance of several CHP configurations with a conventional alternative in terms of primary energy consumption greenhouse gas (GHG) emissions and economic viability. For that a simulation tool has been developed to easily estimate the electrical and thermal energy generated by a hydrogen fuel cell and all associated results related to the hydrogen production alternatives: excess or shortfall of electrical and thermal energy CO2 emission factor overall performance operating costs payback period etc. A feasibility study of different configuration possibilities of the micro-CHP generation system has been carried out considering different heat-to-power ratios (HPRs) in the possible demands and analyzing primary energy savings CO2 emissions savings and operating costs. An extensive parametric study has been performed to analyze the effect of the fuel cell’s electric power and number of annual operation hours as parameters. Finally a study of the influence of the configuration parameters on the final results has been carried out. Results show that in general configurations using hydrogen produced from natural gas save more primary energy than configurations with hydrogen production from electricity. Furthermore it is concluded that the best operating points are those in which the generation system and the demand have similar HPR. It has also been estimated that a reduction in renewable hydrogen price is necessary to make these systems profitable. Finally it has been determined that the most influential parameters on the results are the fuel cell electrical efficiencies hydrogen production efficiency and hydrogen cost.
Can Hydrogen Storage in Metal Hydrides be Economically Competitive with Compressed and Liquid Hydrogen Storage? A Techno-economical Perspective for the Maritime Sector
Aug 2023
Publication
The aim of this work is to evaluate if metal hydride hydrogen storage tanks are a competitive alternative for onboard hydrogen storage in the maritime sector when compared to compressed gas and liquid hydrogen storage. This is done by modelling different hydrogen supply and onboard storage scenarios and evaluating their levelized cost of hydrogen variables. The levelized cost of hydrogen for each case is calculated considering the main components that are required for the refueling infrastructure and adding up the costs of hydrogen production compression transport onshore storage dispensing and the cost of the onboard tanks when known. The results show that the simpler refueling needs of metal hydride-based onboard tanks result in a significant cost reduction of the hydrogen handling equipment. This provides a substantial leeway for the investment costs of metal hydride-based storage which depending on the scenario can be between 3400 - 7300 EUR/kgH2 while remaining competitive with compressed hydrogen storage.
What Does the Public Know About Technological Solutions for Achieving Carbon Neutrality? Citizens' Knowledge of Energy Transition and the Role of Media
Aug 2023
Publication
The present study explores the relation between media use and knowledge in the context of the energy transition. To identify relevant knowledge categories we relied on the expertise of an interdisciplinary research team. Based on this expertise we identified awareness-knowledge of changes in the energy system and principles-knowledge of hydrogen as important knowledge categories. With data obtained from a nationwide online survey of the German-speaking population (n = 2025) conducted in August 2021 we examined the level of knowledge concerning both categories in the German population. Furthermore we studied its associations with exposure to journalistic media and direct communication from non-media actors (e.g. scientists). Our results revealed a considerable lack of knowledge for both categories. Considering the media variables we found only weak and in some cases even negative relations with the use of journalistic media or other actors that spread information online. However we found comparably strong associations between both knowledge categories and the control variables of sex education and personal interest. We use these results to open up a general discussion of the role of the media in knowledge acquisition processes.
Coupling Green Hydrogen Production to Community Benefits: A Pathway to Social Acceptance?
Feb 2024
Publication
Hydrogen energy technologies are forecasted to play a critical supporting role in global decarbonisation efforts as reflected by the growth of national hydrogen energy strategies in recent years. Notably the UK government published its Hydrogen Strategy in August 2021 to support decarbonisation targets and energy security ambitions. While establishing techno-economic feasibility for hydrogen energy systems is a prerequisite of the prospective transition social acceptability is also needed to support visions for the ‘hydrogen economy’. However to date societal factors are yet to be embedded into policy prescriptions. Securing social acceptance is especially critical in the context of ‘hydrogen homes’ which entails replacing natural gas boilers and hobs with low-carbon hydrogen appliances. Reflecting the nascency of hydrogen heating and cooking technologies the dynamics of social acceptance are yet to be explored in a comprehensive way. Similarly public perceptions of the hydrogen economy and emerging national strategies remain poorly understood. Given the paucity of conceptual and empirical insights this study develops an integrated acceptance framework and tests its predictive power using partial least squares structural equation modelling. Results highlight the importance of risk perceptions trust dynamics and emotions in shaping consumer perceptions. Foremost prospects for deploying hydrogen homes at scale may rest with coupling renewable-based hydrogen production to local environmental and socio-economic benefits. Policy prescriptions should embed societal factors into the technological pursuit of large-scale sustainable energy solutions to support socially acceptable transition pathways.
Application and Limitations of Batteries and Hydrogen in Heavy Haul Rail using Australian Case Studies
Oct 2022
Publication
Decarbonisation of heavy haul rail is an essential contributor to a zero-emissions future. However the transition from diesel to battery locomotives is not always practical given the unique characteristics of each haul. This paper demonstrates the limitations of state-of-the-art batteries using real-world data from multiple locomotives operating in Australian rail freight. An energy model was developed to assess each route’s required energy and potential regenerated energy. The tractive and regenerative battery energy mass and cost were determined using data from the energy model coupled with battery specifications. The feasibility of implementing lithium iron phosphate (LFP) nickel manganese cobalt (NMC) and lithium titanium oxide (LTO) chemistries was explored based on cost energy density cycle lifespan and locomotive data. LFP was identified as the most suitable current battery solution based on current chemistries. Further examination of the energy demands and associated mass/volume constraints concluded that three platforms are required for heavy haul rail decarbonisation i) a battery electric locomotive for low-energy demands which can be coupled with either ii) a battery electric tender for medium energy demands or iii) a hydrogen fuel cell electric tender for higher energy demands. A future-looking techno-economic assessment of battery and hydrogen fuel cell platforms concludes that the lowest cost solution for low-energy hauls is a battery-only system and for high-energy hauls a battery-hydrogen system.
Environmental and Material Criticality Assessment of Hydrogen Production via Anion Exchange Membrane Electrolysis
Oct 2023
Publication
The need to drastically reduce greenhouse gas emissions is driving the development of existing and new technologies to produce and use hydrogen. Anion exchange membrane electrolysis is one of these rapidly developing technologies and presents promising characteristics for efficient hydrogen production. However the environmental performance and the material criticality of anion exchange membrane electrolysis must be assessed. In this work prospective life cycle assessment and criticality assessment are applied first to identify environmental and material criticality hotspots within the production of anion exchange membrane electrolysis units and second to benchmark hydrogen production against proton exchange membrane electrolysis. From an environmental point of view the catalyst spraying process heavily dominates the ozone depletion impact category while the production of the membrane represents a hotspot in terms of the photochemical ozone formation potential. For the other categories the environmental impacts are distributed across different components. The comparison of hydrogen production via anion exchange membrane electrolysis and proton exchange membrane electrolysis shows that both technologies involve a similar life-cycle environmental profile due to similar efficiencies and the leading role of electricity generation for the operation of electrolysis. Despite the fact that for proton exchange membrane electrolysis much less material is required due to a higher lifetime anion exchange membrane electrolysis shows significantly lower raw material criticality since it does not rely on platinum-group metals. Overall a promising environmental and material criticality performance of anion exchange membrane electrolysis for hydrogen production is concluded subject to the expected technical progress for this technology.
Green Fleet: A Prototype Biogas and Hydrogen Refueling Management System for Private Fleet Stations
Aug 2023
Publication
Biogas and hydrogen (H2 ) are breaking through as alternative energy sources in road transport specifically for heavy-duty vehicles. Until a public network of service stations is deployed for such vehicles the owners of large fleets will need to build and manage their own refueling facilities. Fleet refueling management and remote monitoring at these sites will become key business needs. This article describes the construction of a prototype system capable of solving those needs. During the design and development process of the prototype the standard industry protocols involved in these installations have been considered and the latest expertise in information technology systems has been applied. This prototype has been essential to determine the Strengths Challenges Opportunities and Risks (SCOR) of such a system which is the first step of a more ambitious project. A second stage will involve setting up a pilot study and developing a commercial system that can be widely installed to provide a real solution for the industry.
An Overview of Application-orientated Multifunctional Large-scale Stationary Battery and Hydrogen Hybrid Energy Storage System
Dec 2023
Publication
The imperative to address traditional energy crises and environmental concerns has accelerated the need for energy structure transformation. However the variable nature of renewable energy poses challenges in meeting complex practical energy requirements. To address this issue the construction of a multifunctional large-scale stationary energy storage system is considered an effective solution. This paper critically examines the battery and hydrogen hybrid energy storage systems. Both technologies face limitations hindering them from fully meeting future energy storage needs such as large storage capacity in limited space frequent storage with rapid response and continuous storage without loss. Batteries with their rapid response (90%) excel in frequent short-duration energy storage. However limitations such as a selfdischarge rate (>1%) and capacity loss (~20%) restrict their use for long-duration energy storage. Hydrogen as a potential energy carrier is suitable for large-scale long-duration energy storage due to its high energy density steady state and low loss. Nevertheless it is less efficient for frequent energy storage due to its low storage efficiency (~50%). Ongoing research suggests that a battery and hydrogen hybrid energy storage system could combine the strengths of both technologies to meet the growing demand for large-scale long-duration energy storage. To assess their applied potentials this paper provides a detailed analysis of the research status of both energy storage technologies using proposed key performance indices. Additionally application-oriented future directions and challenges of the battery and hydrogen hybrid energy storage system are outlined from multiple perspectives offering guidance for the development of advanced energy storage systems.
A Review on Production and Implementation of Hydrogen as a Green Fuel in Internal Combustion Engines
Nov 2022
Publication
Huge and continuously growing non-renewable energy consumption due to human daily activities is accountable for the fossil fuel source crisis in recent decades. The growing concern about the emissions from internal combustion engines also impels the development of new energy sources to replace or reduce conventional non-renewable energy usage. In this context hydrogen is found to be a promising solution in internal combustion engines to address these issues. The novelty of this review is to provide an overview of the use of hydrogen as internal combustion fuel covering the operations in both spark-ignition (SI) and compression-ignition (CI) engines. Majority of the studies had shown that hydrogen enrichment fuels marked incredible engine performance in terms of thermal efficiency fuel consumption and energy consumption. In addition reductions in exhaust emissions such as smoke soot HC CO CO2 and NOx can be achieved in both SI and CI engines with proper operating conditions. Moreover outstanding combustion behaviours were observed in both internal combustion engines with the application of hydrogen fuel. These enhancements were mainly attributed to the physico-chemical properties of hydrogen which exhibits higher calorific value and rapid flaming speed as discussed in this paper. To summarize hydrogen utilisation in the IC and SI engines aided improvements in engine performance exhaust emissions and combustion behaviours under appropriate operating conditions and minor engine modifications such as ignition system and iridium spark plug for SI engines.
Lab-Scale Investigation of the Integrated Backup/Storage System for Wind Turbines Using Alkaline Electrolyzer
Apr 2023
Publication
The depletion of fossil fuel sources has encouraged the authorities to use renewable resources such as wind energy to generate electricity. A backup/storage system can improve the performance of wind turbines due to fluctuations in power demand. The novelty of this study is to utilize a hybrid system for a wind farm using the excess electricity generated by the wind turbines to produce hydrogen in an alkaline electrolyzer (AEL). The hydrogen storage tank stores the produced hydrogen and provides hydrogen to the proton-exchange membrane fuel cell (PEMFC) to generate electricity once the power demand is higher than the electricity generated by the wind turbines. The goal of this study is to use the wind profile of a region in Iran namely the Cohen region to analyze the performance of the suggested integrated system on a micro scale. The output results of this study can be used as a case study for construction in the future based on the exact specification of NTK300 wind turbines. The results indicate that with the minimum power supply of 30 kW from the wind turbines on a lab scale the generated power by the PEMFC will be 1008 W while the maximum generated hydrogen will be 304 mL/h.
Dynamic Quality Tracking of Natural Gas and Hydrogen Mixture in a Portion of Natural Gas Grid
Aug 2015
Publication
Direct injection of alternative fuels (biomethane hydrogen) in the natural gas grid appears to be a promising solution to reach environmental objectives of CO2 emission reduction in the current energy scenario. This approach is justified by the large amount of biogas producible which can be upgraded to biomethane; while another proposed solution to increase renewable energy sources exploitation lies in producing hydrogen from excess wind energy followed by injection in the natural gas grid. Nevertheless compliance with composition limits and quality constraints in the resulting natural gas mixture has to be analysed in both stationary and dynamic operations tracking the gas quality downstream the injection point of the alternative fuels. A model was developed to simulate unsteady operation of a portion of gas grid dealing with realistic industrial and residential consumptions concentrated in offtake points. Two case studies were investigated focusing on the comparison between different amounts of hydrogen injection in the pure natural gas flow yielding composition flow rate and pressure profiles. The analysis shows how imposed quality thresholds can be respected although the hydrogen fraction within the natural gas mixture is highly sensitive to the profile and size of the loads connected to the gas pipeline.
Enhancing Safety through Optimal Placement of Components in Hydrogen Tractor: Rollover Angle Analysis
Feb 2024
Publication
Hydrogen tractors are being developed necessitating consideration of the variation in the center of gravity depending on the arrangement of components such as power packs and cooling modules that replace traditional engines. This study analyzes the effects of component arrangement on stability and rollover angle in hydrogen tractors through simulations and proposes an optimal configuration. Stability is evaluated by analyzing rollover angles in various directions with rotations around the tractor’s midpoint. Based on the analysis of rollover angles for Type 1 Type 2 and Type 3 hydrogen tractors Type 2 demonstrates superior stability compared to the other types. Specifically when comparing lateral rollover angles at 0◦ rotation Type 2 exhibits a 2% increase over Type 3. Upon rotations at 90◦ and 180◦ Type 2 consistently displays the highest rollover angles with differences ranging from approximately 6% to 12% compared to the other types. These results indicate that Type 2 with its specific component arrangement offers the most stable configuration among the three types of tractors. It is confirmed that the rollover angle changes based on component arrangement with a lower center of gravity resulting in greater stability. These findings serve as a crucial foundation for enhancing stability in the future design and manufacturing phases of hydrogen tractors.
Impact of Large-scale Hydrogen Electrification and Retrofitting of Natural Gas Infrastructure on the European Power System
Nov 2023
Publication
In this paper we aim to analyse the impact of hydrogen production decarbonisation and electrification scenarios on the infrastructure development generation mix CO2 emissions and system costs of the European power system considering the retrofit of the natural gas infrastructure. We define a reference scenario for the European power system in 2050 and use scenario variants to obtain additional insights by breaking down the effects of different assumptions. The scenarios were analysed using the European electricity market model COMPETES including a proposed formulation to consider retrofitting existing natural gas networks to transport hydrogen instead of methane. According to the results 60% of the EU’s hydrogen demand is electrified and approximately 30% of the total electricity demand will be to cover that hydrogen demand. The primary source of this electricity would be non-polluting technologies. Moreover hydrogen flexibility significantly increases variable renewable energy investment and production and reduces CO2 emissions. In contrast relying on only electricity transmission increases costs and CO2 emissions emphasising the importance of investing in an H2 network through retrofitting or new pipelines. In conclusion this paper shows that electrifying hydrogen is necessary and cost-effective to achieve the EU’s objective of reducing long-term emissions.
Review on the Thermal Neutrality of Application-orientated Liquid Organic Hydrogen Carrier for Hydrogen Energy Storage and Delivery
Aug 2023
Publication
The depletion and overuse of fossil fuels present formidable challenge to energy supply system and environment. The human society is in great need of clean renewable and sustainable energy which can guarantee the long-term utilization without leading to escalation of greenhouse effect. Hydrogen as an extraordinary secondary energy is capable of realizing the target of environmental protection and transferring the intermittent primary energy to the application terminal while its nature of low volumetric energy density and volatility need suitable storage method and proper carrier. In this context liquid organic hydrogen carrier (LOHC) among a series of storage methods such as compressed and liquefied hydrogen provokes a considerable amount of research interest since it is proven to be a suitable carrier for hydrogen with safety and stability. However the dehydrogenation of hydrogen-rich LOHC materials is an endothermic process and needs large energy consumption which hampers the scale up of the LOHC system. The heat issue is thus essential to be addressed for fulfilling the potential of LOHC. In this work several strategies of heat intensification and management for LOHC system including the microwave irradiation circulation of exhaust heat and direct LOHC fuel cell are summarized and analyzed to provide suggestions and directions for future research.
Experimental Study on the Self-ignition of Pressurized Hydrogen Released into Three-way Tubes
Sep 2021
Publication
To explore the effect of bifurcation structures on the spontaneous ignition and shock wave result from the sudden release of pressurized hydrogen. Three-way tubes with different bifurcation angles (90° 120° 150°) were used in the experiments. They are two Y-shape tubes and one T-shape tube. The photoelectric and pressure signals in the tube were recorded by the sensor. The results show that the reflected shock wave will be formed at the bifurcation. In addition the intensity and velocity of the leading shock wave will attenuate sharply when it passes through the bifurcation.The smaller bifurcation angle of tubethe smaller overpressure decay rate of shock wave at bifurcation position.The smaller the bifurcation angle of tubes the weaker the reflected shock wave transmitted downstream and the greater attenuation of shock wave intensity. Experimental results have reference value for the safety of hydrogen storage at high-pressure and are helpful to understand the influence of different tube structures on spontaneous ignition when hydrogen is transported at high pressure.
Knock Mitigation and Power Enhancement of Hydrogen Spark-Ignition Engine through Ammonia Blending
Jun 2023
Publication
Hydrogen and ammonia are primary carbon-free fuels that have massive production potential. In regard to their flame properties these two fuels largely represent the two extremes among all fuels. The extremely fast flame speed of hydrogen can lead to an easy deflagration-to-detonation transition and cause detonation-type engine knock that limits the global equivalence ratio and consequently the engine power. The very low flame speed and reactivity of ammonia can lead to a low heat release rate and cause difficulty in ignition and ammonia slip. Adding ammonia into hydrogen can effectively modulate flame speed and hence the heat release rate which in turn mitigates engine knock and retains the zero-carbon nature of the system. However a key issue that remains unclear is the blending ratio of NH3 that provides the desired heat release rate emission level and engine power. In the present work a 3D computational combustion study is conducted to search for the optimal hydrogen/ammonia mixture that is knock-free and meanwhile allows sufficient power in a typical spark-ignition engine configuration. Parametric studies with varying global equivalence ratios and hydrogen/ammonia blends are conducted. The results show that with added ammonia engine knock can be avoided even under stoichiometric operating conditions. Due to the increased global equivalence ratio and added ammonia the energy content of trapped charge as well as work output per cycle is increased. About 90% of the work output of a pure gasoline engine under the same conditions can be reached by hydrogen/ammonia blends. The work shows great potential of blended fuel or hydrogen/ammonia dual fuel in high-speed SI engines.
Green Hydrogen and Electrical Power Production through the Integration of CO2 Capturing from Biogas: Process Optimization and Dynamic Control
Jun 2021
Publication
This study describes the optimization of a modelling process concerning biogas’ use to generate green hydrogen and electrical power. The Aspen Plus simulation tool is used to model the procedure and the approach employed to limit the emissions of gas from the hydrogen production process will be the CO2 capture method. This technique uses slack lime (Ca(OH)2) to absorb CO2 capture since it is readily available. The study analyzes many critical parameters in the process including the temperature and pressure in the steam reforming (SR) and the water gas shift (WGS) reactions along with the steam to carbon ratio (S/C) to determine how the production of green hydrogen and electrical power will be influenced. Electricity generation is achieved by taking the residual water from the SR WGS carbonation reactions and converting it to the vapour phase allowing the steam to pass through the turbine to generate electricity. To examine the effects of the synchronized critical parameters response surface methodology (RSM) was used thus allowing the optimal operational conditions to be determined in the form of an optimized zone for operation. The result of parameter optimization gave the maximum green hydrogen production of 211.46 kmol/hr and electric power production of 2311.68 kWh representing increases of 34.86% and 5.62% respectively when using 100 kmol/hr of biogas. In addition control structures were also built to control the reactors’ temperature in the dynamic section. The tuning parameters can control the SR and WGS system’s reactor to maintain the system in approximately 0.29 h and 0.32 h respectively.
Research Progress on Corrosion and Hydrogen Embrittlement in Hydrogen-Natural Gas Pipeline Transportation
Jun 2023
Publication
Hydrogen clean efficient and zero-carbon is seen as a most promising energy source. The use of existing gas pipelines for hydrogenenatural gas transportation is considered to be an effective way to achieve long-distance large-scale efficient and economical hydrogen transportation. However the pipelines for hydrogenenatural gas transportation contain lots of impurities (e.g. CH4 high-pressure H2 H2S and CO2) and free water which will inevitably lead to corrosion and hydrogen embrittlement. This paper presents a systematic review of research and an outlook for corrosion and hydrogen embrittlement in hydrogenenatural gas pipeline transportation. The results show that gasphase hydrogen charging is suitable for hydrogenenatural gas transportation but this technique lacks technical standards. By contrast the liquid-phase hydrogen charging technique is more mature but has large deviation from the engineering reality. In the hydrogenenatural gas transportation pipelines corrosion and hydrogen embrittlement are synergetic and competitive but the failure mechanism and change law when corrosion and hydrogen embrittlement coexist remain unclear which need to be further clarified by experiments. The failure mechanism is believed to be mainly sensitive to three key factors i.e. the H2S/CO2 partial pressure ratio the hydrogen blending ratio and material strength. The increase of the three factors will make the pipeline materials more corrosive and more sensitive to hydrogen embrittlement. The research findings can be used as a reference for research and development of long-distance hydrogenenatural gas transportation technology and will drive the high-quality development of the hydrogenenatural gas blending industry.
The New Model of Energy Cluster Management and Functioning
Sep 2022
Publication
This article was aimed to answer the question of whether local energy communities have a sufficient energy surplus for storage purposes including hydrogen production. The article presents an innovative approach to current research and a discussion of the concepts of the collective prosumer and virtual prosumer that have been implemented in the legal order and further amended in the law. From this perspective it was of utmost importance to analyze the model of functioning of an energy cluster consisting of energy consumers energy producers and hydrogen storage whose goal is to maximize the obtained benefits assuming the co-operative nature of the relationship. The announced and clear perspective of the planned benefits will provide the cluster members a measurable basis for participation in such an energy community. However the catalogue of benefits will be conditioned by the fulfillment of several requirements related to both the scale of covering energy demand from own sources and the need to store surplus energy. As part of the article the results of analyses together with a functional model based on real data of the local energy community are presented.
Low Carbon Optimal Operation of Integrated Energy Systems Considering Air Pollution Emissions
Apr 2023
Publication
To reduce carbon sulfur dioxide (SO2) and nitrogen oxide (NOX) emissions from the integrated energy system (IES) a low carbon optimization strategy for the IES is proposed taking into account carbon SO2 and NOX emissions. Firstly hydrogen production storage and use equipment such as methane reactor electrolysis tank hydrogen fuel cell and hydrogen energy storage are added to the traditional IES to build a multi-energy complementary system of electricity gas cooling thermal and hydrogen. Then this paper introduces a stepped carbon trading mechanism and the model of the emissions of SO2 and NOX. Finally to further reduce its pollutant emissions the model of combined heat and power units and hydrogen fuel cells with adjustable thermoelectric ratio is built. To compare and account for the impact of air pollutant emissions on the optimal low-carbon operation of IES this paper construsted three scenarios with the lowest cost of carbon trading the lowest penalty cost for SO2 and NOX emissions and total operation cost as objective functions respectively The results show that the strategy is effective in reducing air pollutant emissions from integrated energy systems and the outputs of CHP and HFC with adjustable thermoelectric ratios are more flexible and can effectively achieve carbon reduction and pollutant emission reduction.
Evaluation of the Impact of Gaseous Hydrogen on Pipeline Steels Utilizing Hollow Specimen Technique and μCT
Feb 2024
Publication
The high potential of hydrogen as a key factor on the pathway towards a climate neutral economy leads to rising demand in technical applications where gaseous hydrogen is used. For several metals hydrogen-metal interactions could cause a degradation of the material properties. This is especially valid for low carbon and highstrength structural steels as they are commonly used in natural gas pipelines and analyzed in this work. This work provides an insight to the impact of hydrogen on the mechanical properties of an API 5L X65 pipeline steel tested in 60 bar gaseous hydrogen atmosphere. The analyses were performed using the hollow specimen technique with slow strain rate testing (SSRT). The nature of the crack was visualized thereafter utilizing μCT imaging of the sample pressurized with gaseous hydrogen in comparison to one tested in an inert atmosphere. The combination of the results from non-conventional mechanical testing procedures and nondestructive imaging techniques has shown unambiguously how the exposure to hydrogen under realistic service pressure influences the mechanical properties of the material and the appearance of failure.
Reversible Molten Catalytic Methane Cracking Applied to Commercial Solar-Thermal Receivers
Nov 2020
Publication
When driven by sunlight molten catalytic methane cracking can produce clean hydrogen fuel from natural gas without greenhouse emissions. To design solar methane crackers a canonical plug flow reactor model was developed that spanned industrially relevant temperatures and pressures (1150–1350 Kelvin and 2–200 atmospheres). This model was then validated against published methane cracking data and used to screen power tower and beam-down reactor designs based on “Solar Two” a renewables technology demonstrator from the 1990s. Overall catalytic molten methane cracking is likely feasible in commercial beam-down solar reactors but not power towers. The best beam-down reactor design was 9% efficient in the capture of sunlight as fungible hydrogen fuel which approaches photovoltaic efficiencies. Conversely the best discovered tower methane cracker was only 1.7% efficient. Thus a beam-down reactor is likely tractable for solar methane cracking whereas power tower configurations appear infeasible. However the best simulated commercial reactors were heat transfer limited not reaction limited. Efficiencies could be higher if heat bottlenecks are removed from solar methane cracker designs. This work sets benchmark conditions and performance for future solar reactor improvement via design innovation and multiphysics simulation.
Towards a Sustainable Future: Bio-hydrogen Production from Food Waste for Clean Energy Generation
Jan 2024
Publication
To address climate change energy security and waste management new sustainable energy sources must be developed. This study uses Aspen Plus software to extract bio-H2 from food waste with the goal of efficiency and environmental sustainability. Anaerobic digestion optimised to operate at 20-25°C and keep ammonia at 3% greatly boosted biogas production. The solvent [Emim][FAP] which is based on imidazolium had excellent performance in purifying biogas. It achieved a high level of methane purity while consuming a minimal amount of energy with a solvent flow rate of 13.415 m³/h. Moreover the utilization of higher temperatures (600-700°C) during the bio-H2 generation phase significantly enhanced both the amount and quality of hydrogen produced. Parametric and sensitivity assessments were methodically performed at every stage. This integrated method was practicable and environmentally friendly according to the economic assessment. H2 generation using steam reforming results in a TCC of 1.92×106 USD. The CO2 separation step has higher costs (TCC of 2.15×107 USD) due to ionic liquid washing and CO2 liquefaction. Compressor electricity consumption significantly impacts total operating cost (TOC) totaling 4.73×108 USD. showing its ability to reduce greenhouse gas emissions optimize resource utilization and promote energy sustainability. This study presents a sustainable energy solution that addresses climate and waste challenges.
Ammonia as Green Fuel in Internal Combustion Engines: State-of-the-Art and Future Perspectives
Jul 2022
Publication
Ammonia (NH3) is among the largest-volume chemicals produced and distributed in the world and is mainly known for its use as a fertilizer in the agricultural sector. In recent years it has sparked interest in the possibility of working as a high-quality energy carrier and as a carbon-free fuel in internal combustion engines (ICEs). This review aimed to provide an overview of the research on the use of green ammonia as an alternative fuel for ICEs with a look to the future on possible applications and practical solutions to related problems. First of all the ammonia production process is discussed. Present ammonia production is not a “green” process; the synthesis occurs starting from gaseous hydrogen currently produced from hydrocarbons. Some ways to produce green ammonia are reviewed and discussed. Then the chemical and physical properties of ammonia as a fuel are described and explained in order to identify the main pros and cons of its use in combustion systems. Then the most viable solutions for fueling internal combustion engines with ammonia are discussed. When using pure ammonia high boost pressure and compression ratio are required to compensate for the low ammonia flame speed. In spark-ignition engines adding hydrogen to ammonia helps in speeding up the flame front propagation and stabilizing the combustion. In compression-ignition engines ammonia can be successfully used in dual-fuel mode with diesel. On the contrary an increase in NOx and the unburned NH3 at the exhaust require the installation of apposite aftertreatment systems. Therefore the use of ammonia seems to be more practicable for marine or stationary engine application where space constraints are not a problem. In conclusion this review points out that ammonia has excellent potential to play a significant role as a sustainable fuel for the future in both retrofitted and new engines. However significant further research and development activities are required before being able to consider large-scale industrial production of green ammonia. Moreover uncertainties remain about ammonia safe and effective use and some technical issues need to be addressed to overcome poor combustion properties for utilization as a direct substitute for standard fuels.
Thermal Design of a System for Mobile Powersupply
Sep 2023
Publication
Ever more stringent emission regulations for vehicles encourage increasing numbers of battery electric vehicles on the roads. A drawback of storing electric energy in a battery is the comparable low energy density low driving range and the higher propensity to deplete the energy storage before reaching the destination especially at low ambient temperatures. When the battery is depleted stranded vehicles can either be towed or recharged with a mobile recharging station. Several technologies of mobile recharging stations already exist however most of them use fossil fuels to recharge battery electric vehicles. The proposed novel zero emission solution for mobile charging is a combined high voltage battery and hydrogen fuel cell charging station. Due to the thermal characteristics of the fuel cell and high voltage battery (which allow only comparable low coolant temperatures) the thermal design for this specific application (available heat exchanger area zero vehicle speed air flow direction) becomes challenging and is addressed in this work. Experimental methods were used to obtain reliable thermal and electric power measurement data of a 30 kW fuel cell system which is used in the Mobile Hydrogen Powersupply. Subsequently simulation methods were applied for the thermal design and optimisation of the coolant circuits and heat exchangers. It is shown that an battery electric vehicle charging power of 22 kW requires a heat exchanger area of 1 m2 of which 60 % is used by the fuel cell heat exchanger and the remainder by the battery heat exchanger to achieve steady state operation at the highest possible ambient temperature of 436 °C. Furthermore the simulation showed that when the charging power of 22 kW is solely provided by the high voltage battery the highest possible ambient temperature is 42 °C. When the charging power is decreased operation up to the maximum ambient temperatures of 45 °C can be achieved. The results of maximum charging power and limiting ambient temperature give insights for further system improvements which are: sizing of fuel cell or battery trailer design and heat exchanger area operation strategy of the system (power split between high voltage battery and fuel cell) as well as possible dynamic operation scenarios.
Designing a Future-proof Gas and Hydrogen Infrastructure for Europe - A Modelling-based Approach
Jun 2023
Publication
Hydrogen has been at the centre of attention since the EU kicked-off its decarbonization agenda at full speed. Many consider it a silver bullet for the deep decarbonization of technically challenging sectors and industries but it is also an attractive option for the gas industry to retain and future-proof its well-developed infrastructure networks. The modelling methodology presented in this report systematically tests the feasibility and cost of different pipeline transportation methods – blending repurposing and dedicated hydrogen pipelines - under different decarbonization pathways and concludes that blending is not a viable solution and pipeline repurposing can lead to excessive investment outlays in the range of EUR 19–25 bn over the modelled period (2020–2050) for the EU-27.
Investigation of Performance of Anion Exchange Membrane (AEM) Electrolysis with Different Operating Conditions
Mar 2023
Publication
In this work the performance of anion exchange membrane (AEM) electrolysis is evaluated. A parametric study is conducted focusing on the effects of various operating parameters on the AEM efficiency. The following parameters—potassium hydroxide (KOH electrolyte concentration (0.5–2.0 M) electrolyte flow rate (1–9 mL/min) and operating temperature (30–60 ◦C)—were varied to understand their relationship to AEM performance. The performance of the electrolysis unit is measured by its hydrogen production and energy efficiency using the AEM electrolysis unit. Based on the findings the operating parameters greatly influence the performance of AEM electrolysis. The highest hydrogen production was achieved with the operational parameters of 2.0 M electrolyte concentration 60 ◦C operating temperature and 9 mL/min electrolyte flow at 2.38 V applied voltage. Hydrogen production of 61.13 mL/min was achieved with an energy consumption of 48.25 kW·h/kg and an energy efficiency of 69.64%.
Technoeconomic Analysis for Green Hydrogen in Terms of Production, Compression, Transportation and Storage Considering the Australian Perspective
Jul 2023
Publication
This current article discusses the technoeconomics (TE) of hydrogen generation transportation compression and storage in the Australian context. The TE analysis is important and a prerequisite for investment decisions. This study selected the Australian context due to its huge potential in green hydrogen but the modelling is applicable to other parts of the world adjusting the price of electricity and other utilities. The hydrogen generation using the most mature alkaline electrolysis (AEL) technique was selected in the current study. The results show that increasing temperature from 50 to 90 ◦C and decreasing pressure from 13 to 5 bar help improve electrolyser performance though pressure has a minor effect. The selected range for performance parameters was based on the fundamental behaviour of water electrolysers supported with literature. The levelised cost of hydrogen (LCH2 ) was calculated for generation compression transportation and storage. However the majority of the LCH2 was for generation which was calculated based on CAPEX OPEX capital recovery factor hydrogen production rate and capacity factor. The LCH2 in 2023 was calculated to be 9.6 USD/kgH2 using a base-case solar electricity price of 65–38 USD/MWh. This LCH2 is expected to decrease to 6.5 and 3.4 USD/kgH2 by 2030 and 2040 respectively. The current LCH2 using wind energy was calculated to be 1.9 USD/kgH2 lower than that of solar-based electricity. The LCH2 using standalone wind electricity was calculated to be USD 5.3 and USD 2.9 in 2030 and 2040 respectively. The LCH2 predicted using a solar and wind mix (SWM) was estimated to be USD 3.2 compared to USD 9.6 and USD 7.7 using standalone solar and wind. The LCH2 under the best case was predicted to be USD 3.9 and USD 2.1 compared to USD 6.5 and USD 3.4 under base-case solar PV in 2030 and 2040 respectively. The best case SWM offers 33% lower LCH2 in 2023 which leads to 37% 39% and 42% lower LCH2 in 2030 2040 and 2050 respectively. The current results are overpredicted especially compared with CSIRO Australia due to the higher assumption of the renewable electricity price. Currently over two-thirds of the cost for the LCH2 is due to the price of electricity (i.e. wind and solar). Modelling suggests an overall reduction in the capital cost of AEL plants by about 50% in the 2030s. Due to the lower capacity factor (effective energy generation over maximum output) of renewable energy especially for solar plants a combined wind- and solar-based electrolysis plant was recommended which can increase the capacity factor by at least 33%. Results also suggest that besides generation at least an additional 1.5 USD/kgH2 for compression transportation and storage is required.
Energy Assessment of an Integrated Hydrogen Production System
Dec 2022
Publication
Hydrogen is believed to be the future energy carrier that will reduce environmental pollution and solve the current energy crisis especially when produced from a renewable energy source. Solar energy is a renewable source that has been commonly utilized in the production process of hydrogen for years because it is inexhaustible clean and free. Generally hydrogen is produced by means of a water splitting process mainly electrolysis which requires energy input provided by harvesting solar energy. The proposed model integrates the solar harvesting system into a conventional Rankine cycle producing electrical and thermal power used in domestic applications and hydrogen by high temperature electrolysis (HTE) using a solid oxide steam electrolyzer (SOSE). The model is divided into three subsystems: the solar collector(s) the steam cycle and an electrolysis subsystem where the performance of each subsystem and their effect on the overall efficiency is evaluated thermodynamically using first and second laws. A parametric study investigating the hydrogen production rate upon varying system operating conditions (e.g. solar flux and area of solar collector) is conducted on both parabolic troughs and heliostat fields as potential solar energy harvesters. Results have shown that heliostat-based systems were able to attain optimum performance with an overall thermal efficiency of 27% and a hydrogen production rate of 0.411 kg/s whereas parabolic trough-based systems attained an overall thermal efficiency of 25.35% and produced 0.332 kg/s of hydrogen.
Plastic and Waste Tire Pyrolysis Focused on Hydrogen Production—A Review
Dec 2022
Publication
In this review we compare hydrogen production from waste by pyrolysis and bioprocesses. In contrast the pyrolysis feed was limited to plastic and tire waste unlikely to be utilized by biological decomposition methods. Recent risks of pyrolysis such as pollutant emissions during the heat decomposition of polymers and high energy demands were described and compared to thresholds of bioprocesses such as dark fermentation. Many pyrolysis reactors have been adapted for plastic pyrolysis after successful investigation experiences involving waste tires. Pyrolysis can transform these wastes into other petroleum products for reuse or for energy carriers such as hydrogen. Plastic and tire pyrolysis is part of an alternative synthesis method for smart polymers including semi-conductive polymers. Pyrolysis is less expensive than gasification and requires a lower energy demand with lower emissions of hazardous pollutants. Short-time utilization of these wastes without the emission of metals into the environment can be solved using pyrolysis. Plastic wastes after pyrolysis produce up to 20 times more hydrogen than dark fermentation from 1 kg of waste. The research summarizes recent achievements in plastic and tire waste pyrolysis development.
Recent Developments in Methane Decomposition over Heterogenous Catalysts: An Overview
Apr 2020
Publication
The production of hydrogen to be used as an alternative renewable energy has been widely explored. Among various methods for producing hydrogen from hydrocarbons methane decomposition is suitable for generating hydrogen with zero greenhouse gas emissions. The use of high temperatures as a result of strong carbon and hydrogen (C–H) bonds may be reduced by utilizing a suitable catalyst with appropriate catalyst support. Catalysts based on transition metals are preferable in terms of their activeness handling and low cost in comparison with noble metals. Further development of catalysts in methane decomposition has been investigated. In this review the recent progress on methane decomposition in terms of catalytic materials preparation method the physicochemical properties of the catalysts and their performance in methane decomposition were presented. The formation of carbon as part of the reaction was also discussed.
Operating Characteristics Analysis and Capacity Configuration Optimization of Wind-Solar-Hydrogen Hybrid Multi-energy Complementary System
Dec 2023
Publication
Wind and solar energy are the important renewable energy sources while their inherent natures of random and intermittent also exert negative effect on the electrical grid connection. As one of multiple energy complementary route by adopting the electrolysis technology the wind-solar-hydrogen hybrid system contributes to improving green power utilization and reducing its fluctuation. Therefore the moving average method and the hybrid energy storage module are proposed which can smooth the wind-solar power generation and enhance the system energy management. Moreover the optimization of system capacity configuration and the sensitive analysis are implemented by the MATLAB program platform. The results indicate that the 10-min grid-connected volatility is reduced by 38.7% based on the smoothing strategy and the internal investment return rate can reach 13.67% when the electricity price is 0.04 $/kWh. In addition the annual coordinated power and cycle proportion of the hybrid energy storage module are 80.5% and 90% respectively. The developed hybrid energy storage module can well meet the annual coordination requirements and has lower levelized cost of electricity. This method provides reasonable reference for designing and optimizing the wind-solar-hydrogen complementary system.
Operation Optimization of Wind/Battery Storage/Alkaline Electrolyzer System Considering Dynamic Hydrogen Production Efficiency
Aug 2023
Publication
Hydrogen energy is regarded as a key path to combat climate change and promote sustainable economic and social development. The fluctuation of renewable energy leads to frequent start/stop cycles in hydrogen electrolysis equipment. However electrochemical energy storage with its fast response characteristics helps regulate the power of hydrogen electrolysis enabling smooth operation. In this study a multi-objective constrained operation optimization model for a wind/battery storage/alkaline electrolyzer system is constructed. Both profit maximization and power abandonment rate minimization are considered. In addition some constraints such as minimum start/stop times upper and lower power limits and input fluctuation limits are also taken into account. Then the non-dominated sorting genetic algorithm II (NSGA-II) algorithm and the entropy method are used to optimize the operation strategy of the hybrid energy system by considering dynamic hydrogen production efficiency and through optimization to obtain the best hydrogen production power of the system under the two objectives. The change in dynamic hydrogen production efficiency is mainly related to the change in electrolyzer power and the system can be better adjusted according to the actual supply of renewable energy to avoid the waste of renewable energy. Our results show that the distribution of Pareto solutions is uniform which indicates the suitability of the NSGA-II algorithm. In addition the optimal solution indicates that the battery storage and alkaline electrolyzer can complement each other in operation and achieve the absorption of wind power. The dynamic hydrogen production efficiency can make the electrolyzer operate more efficiently which paves the way for system optimization. A sensitivity analysis reveals that the profit is sensitive to the price of hydrogen energy.
Optimized Scheduling of Integrated Energy Systems Accounting for Hydrogen Energy Multi-Utilization Models
Jan 2024
Publication
To cope with the growing penetration rate of renewable energy and to enhance the absorption capacity of wind power this paper investigates the applications of an Integrated Energy System (IES) Hydrogen Compressed Natural Gas (HCNG) and power-to-hydrogen (P2H) devices within the IES. It employs power-to-gas and gas blending with hydrogen to construct an efficient electricity–gas–electricity energy flow loop establishing a Natural Gas–Electricity Coupling System (NGECS) model. On this basis a coordinated scheduling method for gas–electric coupling systems using gas blended with hydrogen is proposed. A carbon trading mechanism is introduced to constrain carbon emissions further reducing the system’s carbon footprint. Multiple scenarios are set up for a comparative analysis in order to validate the effectiveness of the proposed model. This study also analyzes the impact of different hydrogen blending ratios and methods on the low-carbon and economic performance of IES.
Geomechanics of Hydrogen Storage in a Depleted Gas Field
Feb 2024
Publication
We perform a simulation study of hydrogen injection in a depleted gas reservoir to assess the geomechanical impact of hydrogen storage relative to other commonly injected gases (methane CO2). A key finding is that the differences in hydrogen density compressibility viscosity and thermal properties compared to the other gases result in significantly less thermal perturbation at reservoir level. The risks of fault reactivation and wellbore fractures due to thermally-induced stress changes are significantly lower when storing hydrogen compared to results observed in CO2 scenarios. This implies that hydrogen injection and production has a much smaller geomechanical footprint with benefits for operational safety. We also find that use of nitrogen cushion gas ensures efficient deliverability and phase separation in the reservoir. However in this study a large fraction of cushion gas was back-produced in each cycle demonstrating the need for further studies of the surface processing requirements and economic implications.
An Overview on the Technologies Used to Storage Hydrogen
Aug 2023
Publication
Hydrogen energy has a significant potential in mitigating the intermittency of renewable energy generation by converting the excess of renewable energy into hydrogen through many technologies. Also hydrogen is expected to be used as an energy carrier that contribute to the global decarbonization in transportation industrial and building sectors. Many technologies have been developed to store hydrogen energy. Hydrogen can be stored to be used when needed and thus synchronize generation and consumption. The current paper presents a review on the different technologies used to store hydrogen. The storage capacity advantages drawbacks and development stages of various hydrogen storage technologies were presented and compared.
Geochemical Effects on Storage Gases and Reservoir Rock during Underground Hydrogen Storage: A Depleted North Sea Oil Reservoir Case Study
May 2023
Publication
In this work geochemical modelling using PhreeqC was carried out to evaluate the effects of geochemical reactions on the performance of underground hydrogen storage (UHS). Equilibrium exchange and mineral reactions were considered in the model. Moreover reaction kinetics were considered to evaluate the geochemical effect on underground hydrogen storage over an extended period of 30 years. The developed model was first validated against experimental data adopted from the published literature by comparing the modelling and literature values of H2 and CO2 solubility in water at varying conditions. Furthermore the effects of pressure temperature salinity and CO2% on the H2 and CO2 inventory and rock properties in a typical sandstone reservoir were evaluated over 30 years. Results show that H2 loss over 30 years is negligible (maximum 2%) through the studied range of conditions. The relative loss of CO2 is much more pronounced compared to H2 gas with losses of up to 72%. Therefore the role of CO2 as a cushion gas will be affected by the CO2 gas losses as time passes. Hence remedial CO2 gas injections should be considered to maintain the reservoir pressure throughout the injection and withdrawal processes. Moreover the relative volume of CO2 increases with the increase in temperature and decrease in pressure. Furthermore the reservoir rock properties porosity and permeability are affected by the underground hydrogen storage process and more specifically by the presence of CO2 gas. CO2 dissolves carbonate minerals inside the reservoir rock causing an increase in the rock’s porosity and permeability. Consequently the rock’s gas storage capacity and flow properties are enhanced
Lifetime Greenhouse Gas Emissions from Offshore Hydrogen Production
Aug 2023
Publication
With a limited global carbon budget it is imperative that decarbonisation decisions are based on accurate holistic accounts of all greenhouse gas (GHG) emissions produced to assess their validity. Here the upstream GHG emissions of potential UK offshore Green and Blue hydrogen production are compared to GHG emissions from hydrogen produced through electrolysis using UK national grid electricity and the ‘business-as-usual’ case of continuing to combust methane. Based on an operational life of 25 years and producing 0.5MtH2 per year for each hydrogen process the results show that Blue hydrogen will emit between 200-262MtCO2e of GHG emissions depending on the carbon capture rates achieved (39%–90%) Green hydrogen produced via electrolysis using 100% renewable electricity from offshore wind will emit 20MtCO2e and hydrogen produced via electrolysis powered by the National Grid will emit between 103-168MtCO2e depending of the success of its NetZero strategy. The ‘business-as-usual’ case of continuing to combust methane releases 250MtCO2e over the same lifetime. This study finds that Blue hydrogen at scale is not compatible with the Paris Agreement reduces energy security and will require a substantial GHG emissions investment which excludes it from being a ‘low carbon technology’ and should not be considered for any decarbonisation strategies going forward.
Hydrogen Impact: A Review on Diffusibility, Embrittlement Mechanisms, and Characterization
Feb 2024
Publication
Hydrogen embrittlement (HE) is a broadly recognized phenomenon in metallic materials. If not well understood and managed HE may lead to catastrophic environmental failures in vessels containing hydrogen such as pipelines and storage tanks. HE can affect the mechanical properties of materials such as ductility toughness and strength mainly through the interaction between metal defects and hydrogen. Various phenomena such as hydrogen adsorption hydrogen diffusion and hydrogen interactions with intrinsic trapping sites like dislocations voids grain boundaries and oxide/matrix interfaces are involved in this process. It is important to understand HE mechanisms to develop effective hydrogen resistant strategies. Tensile double cantilever beam bent beam and fatigue tests are among the most common techniques employed to study HE. This article reviews hydrogen diffusion behavior mechanisms and characterization techniques.
No more items...