Safety
A Study on Dispersion Resulting From Liquefied Hydrogen Spilling
Oct 2015
Publication
For massive utilization of hydrogen energy it is necessary to transport a large quantity of hydrogen by liquefied hydrogen carriers. However the current rule on ships carrying liquefied hydrogen in bulks do not address the maritime transport of liquefied hydrogen and the safety assessment of liquefied hydrogen carriage is thus very important. In the present study we spilled liquefied hydrogen and LNG (Liquefied Natural Gas) on the surface of various materials and compared the difference of their spread and dispersion. Liquefied hydrogen immediately dispersed upward compared to LNG. Furthermore we also measured the flammability limit of low temperature hydrogen gas. Its range at low temperature was narrower than the range at normal temperature.
Application of Risk Assessment Approach on a Hydrogen Station
Sep 2013
Publication
An accident modelling approach is used to assess the safety of a hydrogen station as part of a ground transportation network. The method incorporates prevention barriers associated to human factors management and organizational failures in a risk assessment framework. Failure probabilities of these barriers and end-states events are predicted using Fault Tree Analysis and Event Tree Analysis respectively. Results from the case study considered revealed the capability of the proposed method in estimating the likelihood of various outcomes as well as predicting the future probability. In addition the scheme offers opportunity to provide dynamic adjustment by updating the failure probability with actual plant data. Results from the analysis can be used to plan maintenance and management of change as required by the plant condition.
Visualization of Auto-ignition Phenomenon Under the Controlled Burst Pressure
Oct 2015
Publication
A high-pressure hydrogen jet released into the air has the possibility of igniting in a tube without any ignition source. The mechanism of this phenomenon called spontaneous ignition is considered to be that hydrogen diffuses into the hot air caused by the shock wave from diaphragm rupture and the hydrogen-oxidizer mixed region is formed enough to start chemical reaction. Recently flow visualization studies on the spontaneous ignition process have been conducted to understand its detailed mechanism but such ignition has not yet been well clarified. In this study the spontaneous ignition phenomenon was observed in a rectangular tube. The results confirm the presence of a flame at the wall of the tube when the shock wave pressure reaches 1.2–1.5 MPa in more than 9 MPa burst pressure and that ignition occurs near the wall followed by multiple ignitions as the shock wave propagates with the ignitions eventually combining to form a flame.
Simulation of the Fast Filling of Hydrogen Tanks
Sep 2009
Publication
High pressure storage of hydrogen in tanks is a promising option to provide the necessary fuel for transportation purposes. The fill process of a high-pressure tank should be reasonably short but must be designed to avoid too high temperatures in the tank. The shorter the fill should be the higher the maximum temperature in the tank climbs. For safety reasons an upper temperature limit is included in the requirements for refillable hydrogen tanks (ISO 15869) which sets the limit for any fill optimization. It is crucial to understand the phenomena during a tank fill to stay within the safety margins.<br/>The paper describes the fast filling process of hydrogen tanks by simulations based on the Computational Fluid Dynamics (CFD) code CFX. The major result of the simulations is the local temperature distribution in the tank depending on the materials of liner and outer thermal insulation. Different material combinations (type III and IV) are investigated.<br/>Some measurements from literature are available and are used to validate the approach followed in CFX to simulate the fast filling of tanks. Validation has to be continued in future to further improve the predictability of the calculations for arbitrary geometries and material combinations.
Numerical Simulations of Spontaneous Ignition of High-pressure Hydrogen Based on Detailed Chemical Kinetics
Sep 2013
Publication
A two-dimensional (2-D) simulation of spontaneous ignition of high-pressure hydrogen in a length of duct is conducted in order to explore its underlying ignition mechanisms. The present study adopts a 2-D rectangular duct (i.e. not axisymmetric geometry) and focuses on the effects of initial diaphragm shape on the spontaneous ignitions. The Navier-Stokes equations with a detailed chemical kinetics mechanism are solved in a manner of direct numerical simulation. The detailed mechanisms of spontaneous ignition are discussed for each initial diaphragm shape. For a straight diaphragm shape it is found that the ignition occurs only near the wall due to the adiabatic wall condition while the three ignition events: ignitions due to leading shock wave reflection at the wall hydrogen penetration into shock-heated air near the wall and deep penetration of hydrogen into shock-heated air behind the leading shock wave are identified for a largely deformed diaphragm shape.
QRA Including Utility for Decision Support of H2 Infrastructure Licensing
Sep 2011
Publication
Rational decision making in land use planning and licensing of H2 infrastructure surrounded by other industrial activities and population should take account of individual and societal risks. QRA produces a risk matrix of potential consequences versus event probabilities that is shrouded in ambiguity and lacking transparency. NIMBY and conflict are lurking. To counter these issues risk analysts should therefore also determine the utilities of decision alternatives which describe desirability of benefits on a single scale. Rationally weighing risks versus benefits results in more transparent and defendable decisions. Example risk analyses of two types of refuelling stations and three hydrogen supply transportation types applying Influence Diagram/BBNs are worked out. Keywords: risk assessment influence diagram decision making land use planning
Numerical Study on Detailed Mechanism of H2-Air Flame Jet Ignition
Sep 2013
Publication
Jet ignition was recognized in the 1970s and has since been applied to automobile engines such as the Honda CVCC. In the 1990s jet ignition was observed in explosions and was seen as a problem that may relate to jet ignition. Our group presented jet ignition experimentally and numerically in 1999 and later using LIF measurements with the same experimental vessel as used in 1999. However the detailed mechanism of jet ignition was not clarified at that time. The target of this study is to clarify how jet ignition happens and to understand the detailed mechanism of flame jet ignition.
Safety Considerations for Hydrogen Test Cells
Sep 2009
Publication
The properties of hydrogen compared to conventional fuels such as gasoline and diesel are substantially different requiring adaptations to the design and layout of test cells for hydrogen fuelled engines and vehicles. A comparison of hydrogen fuel properties versus conventional fuels in this paper provides identification of requirements that need to be adapted to design a safe test cell. Design examples of actual test cells are provided to showcase the differences in overall layout and ventilation safety features fuel supply and metering and emissions measurements. Details include requirements for ventilation patterns the necessity for engine fume hoods as well as hydrogen specific intake and exhaust design. The unique properties of hydrogen in particular the wide flammability limits and nonvisible flames also require additional safety features such as hydrogen sensors and flame cameras. A properly designed and implemented fuel supply system adds to the safety of the test cell by minimizing the amount of hydrogen that can be released. Apart from this the properties of hydrogen also require different fuel consumption measurement systems pressure levels of the fuel supply system additional ventilation lines strategically placed safety solenoids combined with appropriate operational procedures. The emissions measurement for hydrogen application has to be expanded to include the amount of unburned hydrogen in the exhaust as a measurement of completeness of combustion. This measurement can also be used as a safety feature to avoid creation of ignitable hydrogen-air mixtures in the engine exhaust. The considerations provided in this paper lead to the conclusion that hydrogen IC engines can be safely tested however properly designed test cell and safety features have to be included to mitigate the additional hazards related to the change in fuel characteristics.
Ignited Releases of Liquid Hydrogen
Jan 2014
Publication
If the hydrogen economy is to progress more hydrogen fuelling stations are required. In the short term in the absence of a hydrogen distribution network these fuelling stations will have to be supplied by liquid hydrogen (LH2) road tanker. Such a development will increase the number of tanker offloading operations significantly and these may need to be performed in close proximity to the general public.<br/>Several research projects have been undertaken already at HSL with the aim of identifying and addressing hazards relating to the storage and transport of bulk LH2 that are associated with hydrogen refuelling stations located in urban environments.<br/>The first phase of the research was to produce a position paper on the hazards of LH2 (Pritchard and Rattigan 2009). This was published as an HSE research report RR769 in 2010. <br/>The second phase developed an experimental and modelling strategy for issues associated with LH2 spills and was published as an internal report HSL XS/10/06. The subsequent experimental work is a direct implementation of that strategy. LH2 was first investigated experimentally (Royle and Willoughby 2012 HSL XS/11/70) as large-scale spills of LH2 at a rate of 60 litres per minute. Measurements were made on unignited releases which included the concentration of hydrogen in air thermal gradients in the concrete substrate liquid pool formation and temperatures within the pool. Computational modelling on the un-ignited spills was also performed (Batt and Webber 2012 HSL MSU/12/01).<br/>The experimental work on ignited releases of LH2 detailed in this report is a direct continuation of the work performed by Royle and Willoughby.<br/>The aim of this work was to determine the hazards and severity of a realistic ignited spill of LH2 focussing on; flammability limits of an LH2 vapour cloud flame speeds through an LH2 vapour cloud and subsequent radiative heat and overpressures after ignition. The results of the experimentation will inform the wider hydrogen community and contribute to the development of more robust modelling tools. The results will also help to update and develop guidance for codes and standards.
Safety Considerations and Approval Procedures for the Integration of Fuel Cells on Board of Ships
Sep 2009
Publication
The shipping industry is becoming increasingly visible on the global environmental agenda. Shipping's hare of emissions to air is regarded to be significant and public concern lead to ongoing political pressure to reduce shipping emissions. International legislation at the IMO governing the reduction of SOx and NOx emissions from shipping is being enforced and both the European Union and the USA are planning to introduce additional regional laws to reduce emissions. Therefore new approaches for more environmental friendly and energy efficient energy converter are under discussion. One possible solution will be the use of fuel cell systems for auxiliary power or main propulsion. The presentation summarizes the legal background in international shipping related to the use for gas as ship fuel and fuel cells. The focus of the presentation will be on the safety principles for the use of gas as fuel and fuel cells on board of ships and boats. The examples given show the successful integration of such systems on board of ships. Furthermore a short outlook will be given to the ongoing and planed projects for the use of fuel cells on board of ships.
Experimental Study of the Effects of Vent Geometry on the Dispersion of a Buoyant Gas in a Small Enclosure
Sep 2011
Publication
We present an experimental study on the dispersion of helium in an enclosure of 1 m3 with natural ventilation through one vent. Three vent geometries have been studied. Injection parameters have been varied so that the injection Richardson number ranges from 2·10−6 to 9 and the volume Richardson number which gives the ability of the release to mix the enclosure content ranges from 8·10−4 to 900. It has been found that the vertical distribution of helium volume fraction can exhibit significant gradient. Nevertheless the results are compared to the simple analytical model based on the homogenous mixture hypothesis which gives fairly good estimates of the maximum helium volume fraction.
Delayed Explosion of Hydrogen High Pressure Jets in a Highly Obstructed Geometry
Sep 2017
Publication
Delayed explosions of accidental high pressure hydrogen releases are an important risk scenario in safety studies of production plants transportation pipelines and fuel cell vehicles charging stations. Such explosions were widely explored in multiple experimental and numerical investigations. Explosion of high pressure releases in highly obstructed geometries with high blockage ratio is a much more complicated phenomenon. This paper is dedicated to the experimental investigation of the influence of obstacles on a delayed deflagration of hydrogen jets. The computational fluid dynamics (CFD) code FLACS is used to reproduce experimental data. In the current study the computed overpressure signals are compared to the experimentally measured ones at different monitoring points. Simulations are in close agreement with experimental results and can be used to predict overpressure where experimental pressure detectors were saturated. For homogenous stationary clouds a new approach of equivalent mixture of H2/air (~16.5%) to stoichiometric mixture of CH4/air is suggested. This approach is validated versus experimental data from the literature in terms of overpressure maxima. A parametric study is performed using FLACS for various concentrations in the same geometry in order to identify a possible transition from deflagration to detonation.
A Numerical Simulation of Hydrogen Diffusion for the Hydrogen Leakage from a Fuel Cell Vehicle in an Underground Parking Garage
Sep 2011
Publication
In the present study the diffusion process of hydrogen leaking from a FCV (Fuel Cell Vehicle) in an underground parking garage is analyzed by numerical simulations in order to assess the risk of a leakage accident. The temporal and spatial evolution of the hydrogen concentration as well as the flammable region in the parking garage was predicted numerically. The effects of the leakage flow rate and an additional ventilation fan were investigated to evaluate the ventilation performance to relieve the accumulation of the hydrogen gas. The volume of the flammable region shows a non-linear growth in time and rapidly increases eventually. The present numerical analysis can provide a physical insight and quantitative data for safety of various hydrogen applications.
Allowable Hydrogen Permeation Rate From Road Vehicle Compressed Gaseous Storage Systems In Garages- Part 1- Introduction, Scenarios, and Estimation of an Allowable Permeation Rate
Sep 2009
Publication
The paper presents an overview of the main results of the EC NOE HySafe activity to estimate an allowable hydrogen permeation rate for automotive legal requirements and standards. The work was undertaken as part of the HySafe internal project InsHyde.<br/>A slow long term hydrogen release such as that due to permeation from a vehicle into an inadequately ventilated enclosed structure is a potential risk associated with the use of hydrogen in automotive applications. Due to its small molecular size hydrogen permeates through the containment materials found in compressed gaseous hydrogen storage systems and is an issue that requires consideration for containers with non-metallic (polymer) liners. Permeation from compressed gaseous hydrogen storage systems is a current hydrogen safety topic relevant to regulatory and standardisation activities at both global and regional levels.<br/>Various rates have been proposed in different draft legal requirements and standards based on different scenarios and the assumption that hydrogen dispenses homogeneously. This paper focuses on the development of a methodology by HySafe Partners (CEA NCSRD. University of Ulster and Volvo Technology) to estimate an allowable upper limit for hydrogen permeation in automotive applications by investigating the behaviour of hydrogen when released at small rates with a focus on European scenario. The background to the activity is explained. reasonable scenarios are identified a methodology proposed and a maximum hydrogen permeation rate from road vehicles into enclosed structures is estimated The work is based on conclusions from the experimental and numerical investigations described by CEA NCSRD and the University of Ulster in related papers.
The Hydrogen Economy - Evaluation of the Materials Science and Engineering Issues
Jan 2005
Publication
The main objectives were to identify materials issues relating to the widespread use of hydrogen as a fuel.
MAIN FINDINGS
MAIN FINDINGS
- Hydrogen is seen by many as the answer to the environmental problems of reliance on fossil fuels for energy needs. A great deal of effort is currently being invested in research into all areas of the hydrogen economy such as fuel cells hydrogen generation transportation and storage.
- Fuel cells have the potential to provide power for a very wide range of applications ranging from small portable electronics devices to large stationary electricity production and vehicles covering the whole range of road vehicles and possibly extending to rail marine and even aviation.
- The main obstacles to achieving a viable hydrogen economy are costs of producing hydrogen from renewable sources issues relating to transportation and storage due to the low energy density of hydrogen gas and the cost and reliability of fuel cells.
- The main material considerations relating to the use of hydrogen are hydrogen embrittlement material properties at cryogenic temperatures (due to use of liquid hydrogen) and permeability.
- A number of new materials are likely to come to prominence in a hydrogen economy; high performance composites are likely to be used extensively for high pressure hydrogen cylinders new materials or combinations of materials may be used for hydrogen pipelines and a range of new materials are currently being considered for hydrogen storage such as metal hydrides and carbon nanotubes.
- Due to the effect of hydrogen on materials it is important to test any materials in the environment in which they would be used. Depending on the type of test this could require the use of very specialist expensive equipment.
Status, Gaps and Recommendations Regarding Standardisation and the Use of Hydrogen in Sustainable Buildings
Sep 2013
Publication
The use of and interpretation of Regulations Codes and Standards is important input when developing hydrogen systems and applications. This paper presents the work related to standardisation undertaken by DNV as part of the EU supported project H2SusBuild. During the H2SusBuild project a renewable (solar and wind) based full scale energy system with components for hydrogen storage hydrogen production by electrolysis and hydrogen consumption by fuel cell and burner was built and integrated into an existing office building in Lavrion Greece. The relevant standards identified and applied the standardisation gaps identified and the recommendations made for further standardisation activities are presented.
H-Mat Hydrogen Compatibility of Polymers and Elastomers
Sep 2019
Publication
The H2@Scale program of the U.S. Department of Energy (DOE) Fuel Cell Technologies Office is supporting work on the hydrogen compatibility of polymers to improve the durability and reliability of materials for hydrogen infrastructure. The hydrogen compatibility program (H-Mat) seeks “to address the challenges of hydrogen degradation by elucidating the mechanisms of hydrogen-materials interactions with the goal of providing science-based strategies to design materials (micro)structures and morphology with improved resistance to hydrogen degradation.” This research has found hydrogen and pressure interactions with model rubber-material compounds demonstrating volume change and compression-set differences in the materials. The research leverages state-of-the-art capabilities of the DOE national labs. The materials were investigated using helium-ion microscopy which revealed significant morphological changes in the plasticizer incorporating compounds after exposure as evidenced by time-of-flight secondary ion mass spectrometry. Additional studies using transmission electron microscopy and nuclear magnetic resonance revealed that nanosized inclusions developed after gas decompression in rubber- and plasticizer-only materials; this is an indication of void formation at the nanometer level.
Comparisons of Helium and Hydrogen Releases in 1 M3 and 2 M3 Two Vents Enclosures: Concentration Measurements at Different Flow Rates and for Two Diameters of Injection Nozzle
Oct 2015
Publication
This work presents a parametric study on the similitude between hydrogen and helium distribution when released in the air by a source located inside of a naturally ventilated enclosure with two vents. Several configurations were experimentally addressed in order to improve knowledge on dispersion. Parameters were chosen to mimic operating conditions of hydrogen energy systems. Thus the varying parameters of the study were mainly the source diameter the releasing flow rate the volume and the geometry of the enclosure. Two different experimental set-ups were used in order to vary the enclosure's height between 1 and 2 m. Experimental results obtained with helium and hydrogen were compared at equivalent flow rates determined with existing similitude laws. It appears for the plume release case that helium can suitably be used for predicting hydrogen dispersion in these operating designs. On the other hand – when the flow turns into a jet – non negligible differences between hydrogen and helium dispersion appear. In this case helium – used as a direct substitute to hydrogen – will over predict concentrations we would get with hydrogen. Therefore helium concentration read-outs should be converted to obtain correct predictions for hydrogen. However such a converting law is not available yet.
Safety and Regulatory Challenges of Using Hydrogen/Natural Gas Blends in the UK
Sep 2019
Publication
The addition of hydrogen to natural gas for heating and cooking is being considered as a route to reducing carbon emissions in the United Kingdom (UK). The HyDeploy programme (hereafter referred to as HyDeploy) aims to demonstrate that hydrogen can be added to the natural gas supply without compromising public safety or appliance performance. This paper relates to the preparatory work for hydrogen injection on a live site at Keele University closed network comprising domestic premises multi-occupancy buildings and light commercial premises. The project is based around the injection of up to 20 %mol/mol hydrogen into mains natural gas at pressures below 2 barg. Work streams addressed during the pre-trial preparation included; assessment of material interaction with hydrogen blends for all distribution system components and appliances; understanding of gas appliance behaviour; review of: gas detection systems fire and explosion considerations routine and emergency procedural considerations; and the design of a new hydrogen injection grid entry unit. This paper describes the safety and regulatory challenges that were encountered during preparation of the project including obtaining the necessary regulatory permissions to blend hydrogen gas.
Effect of Temperature on Laminar Flame Velocity for Hydrogen-air Mixtures at Reduced Pressures
Sep 2013
Publication
The work was done with respect to hydrogen safety of ITER vacuum vessel in cases of loss of cooling and loss of vacuum accidents. Experiments were conducted at sub-atmospheric pressures from 1 bar to 200 mbar and elevated temperatures up to 300 oC. Hydrogen concentration was changed from lower to upper flammability limits in all the range of pressures and temperatures. The experiments were performed in a spherical explosion bomb equipped with two quartz windows. The flame propagation velocity was measured using pressure method and high speed shadow cinematography. The theoretical flame velocities were calculated by Cantera code using Lutz and Mueller mechanisms. The influence of the initial temperature and pressure conditions on the laminar flame speed SL overall reaction order n and Markstein length LM are presented in this work and compared with the results of a theoretical model.
No more items...