Italy

Air pollution and traffic congestion are two of the major issues affecting public authorities policy makers and citizens not only in Italy and European Union but worldwide; this is nowadays witnessed by always more frequent limitations to the traffic in most of Italian cities for instance. Hydrogen use in automotive appears to offer a viable solution in medium-long term; this new perspective involves the need to carry out adequate infrastructures for distribution and refuelling and consequently the need to improve knowledge on hydrogen technologies from a safety point of view. In the present work possible different configurations for gaseous hydrogen refuelling station has been compared: “stand-alone” and “multi-fuel”. These two alternative scenarios has been taken into consideration each of one with specific hypotheses: “stand-alone” configuration based on the hypothesis of a potential model consisting of a hydrogen refuelling station composed by on-site hydrogen production via electrolysis a trailer of compressed gas for back-up compressor unit intermediate storage unit and dispenser. In this model it is assumed that no other refuelling equipment and/or dispenser of traditional fuel is present in the same site. “multi-fuel” configuration where it is assumed that the same components for hydrogen refuelling station are placed in the same site beside one or more refuelling equipment and/or dispenser of traditional fuel. Comparisons have been carried out from the point of view of specific risk assessment which have been conducted on both the two alternative scenarios.

A method for determination of hazardous zones for hydrogen installations has been studied. This work has been carried out within the NoE HySafe. The method is based on the Italian Method outlined in Guide 31-30(2004) Guide 31–35(2001) Guide 31-35/A(2001) and Guide 31-35/A; V1(2003). Hazardous zones for a “generic hydrogen refuelling station”(HRS) are assessed based on this method. The method is consistent with the EU directive 1999/92/EC “Safety and Health Protection of Workers potentially at risk from explosive atmospheres” which is the basis for determination of hazardous zones in Europe. This regulation is focused on protection of workers and is relevant for hydrogen installations such as hydrogen refuelling stations repair shops and other stationary installations where some type of work operations will be involved. The method is also based on the IEC standard and European norm IEC/EN60079-10 “Electrical apparatus for explosive gas atmospheres. Part 10 Classification of hazardous areas”. This is a widely acknowledged international standard/norm and it is accepted/approved by Fire and Safety Authorities in Europe and also internationally. Results from the HySafe work and other studies relevant for hydrogen and hydrogen installations have been included in the case study. Sensitivity studies have been carried out to examine the effect of varying equipment failure frequencies and leak sizes as well as environmental condition (ventilation obstacles etc.). The discharge and gas dispersion calculations in the Italian Method are based on simple mathematical formulas. However in this work also CFD (Computational Fluid Dynamics) and other simpler numerical tools have been used to quantitatively estimate the effect of ventilation and of different release locations on the size of the flammable gas cloud. Concentration limits for hydrogen to be used as basis for the extent of the hazardous zones in different situations are discussed.

The following paper describes researches to evaluate the behaviour under various accidental conditions of systems of transport compressed hydrogen. Particularly have been considered gaseous tube trailer and the packages cylinders employed for the road transport which have an internal gas pressures up to 200 barg.<br/>Further to a verification of the actual safety conditions this analysis intends to propose a theme that in the next future if confirmed projects around the employment of hydrogen as possible source energetic alternative could become quite important. The general increase of the consumptions of hydrogen and the consequently probable increase of the transports of gaseous hydrogen in pressure they will make the problem of the safety of the gaseous tube trail particularly important. Gaseous tube trailers will also use as components of plant. for versatility easy availability' and inexpensiveness.<br/>The first part of the memory is related to the analysis of the accidents happened in the last year in Italy with compressed hydrogen transports and particularly an accurate study has been made on the behaviour of a gaseous tube trailer involved in fire following a motorway accident in March 2003. In the central part of the job has been done a safety analysis of the described events trying to make to also emerge the most critical elements towards the activities developed by the teams of help intervened.<br/>Finally in the last part you are been listed on the base of the picked data a series of proposals and indications of the possible structural and procedural changes that could be suggested with the purpose to guarantee more elevated safety levels.

Hydrogen is increasingly receiving a primary role as an energy vector in ensuring the achievement of the European decarbonization goals by 2050. In fact Hydrogen could be produced also by electrolysis of water using renewable sources such as photovoltaic and wind power being able to perform the energy storage function as well as through injection into natural gas infrastructures. However hydrogen injection directly impacts thermodynamic properties of the gas itself such as density calorific value Wobbe index sound speed etc. Consequently this practice leads to changes in metrological behavior especially in terms of volume and gas quality measurements. In this paper the authors present an overview on the impact of hydrogen injection in natural gas measurements. In particular the changes in thermodynamic properties of the gas mixtures with different H2 contents have been evaluated and the effects on the accuracy of volume conversion at standard conditions have been investigated both on the theoretical point of view and experimentally. To this end the authors present and discuss the effect of H2 injection in gas networks on static ultrasonic domestic gas meters both from a theoretical and an experimental point of view. Experimental tests demonstrated that ultrasonic gas meters are not significantly affected by H2 injection up to about 10%.

The release of gases heavier than air like propane at ground level or lighter than air like hydrogen close to a ceiling can both lead to fire and explosion hazards that must be carefully considered in safety analyses. Even if the simulation of accident scenarios in complex installations and long transients often appears feasible only using lumped parameter computer codes the phenomenon of denser or lighter gas dispersion is not implicitly accounted by these kind of tools. In the aim to set up an ad hoc model to be used in the computer code ECART fluid-dynamic simulations by the commercial FLUENT 6.0 CFD code are used. The reference geometry is related to cavities having variable depth (2 to 4 m) inside long tunnels filled with a gas heavier or lighter than air (propane or hydrogen). Three different geometrical configurations with a cavity width of 3 6 and 9 m are considered imposing different horizontal air stream velocities ranging from 1 to 5 m/s. A stably-stratified flow region is observed inside the cavity during gas shearing. In particular it is found that the density gradient tends to inhibit turbulent mixing thus reducing the dispersion rate. The obtained data are correlated in terms of main dimensionless groups by means of a least squares method. In particular the Sherwood number is correlated as a function of Reynolds a density ratio modified Froude numbers and in terms of the geometrical parameter obtained as a ratio between the depth of the air-dense gas interface and the length of the cavity. This correlation is implemented in the ECART code to add the possibility to simulate large installations during complex transients lasting many hours with reasonable computation time. An example of application to a typical case is presented.

In a scenario characterized by an increasing penetration of non-dispatchable renewable energy sources and the need of fast-ramping grid-balancing power plants the EU project GRASSHOPPER aims to setup and demonstrate a highly flexible PEMFC Power Plant hydrogen fueled and scalable to MW-size designed to provide grid support.<br/>In this work different layouts proposed for the innovative MW-scale plant are simulated to optimize design and off-design operation. The simulation model details the main BoP components performances and includes a customized PEMFC model validated through dedicated experiments.<br/>The system may operate at atmospheric or mild pressurized conditions: pressurization to 0.7 barg allows significantly higher net system efficiency despite the increasing BoP consumptions. The additional energy recovery from the cathode exhaust with an expander gives higher net power and net efficiency adding up to 2%pt and reaching values between 47%LHV and 55%LHV for currents between 100% and 20% of the nominal value.

Industrial and public interest in hydrogen technologies has risen strongly recently as hydrogen is the ideal means for medium to long term energy storage transport and usage in combination with renewable and green energy supply. In a future energy system the production storage and usage of green hydrogen is a key technology. Hydrogen is and will in future be even more used for industrial production processes as a reduction agent or for the production of synthetic hydrocarbons especially in the chemical industry and in refineries. Under certain conditions material based systems for hydrogen storage and compression offer advantages over the classical systems based on gaseous or liquid hydrogen. This includes in particular lower maintenance costs higher reliability and safety. Hydrogen storage is possible at pressures and temperatures much closer to ambient conditions. Hydrogen compression is possible without any moving parts and only by using waste heat. In this paper we summarize the newest developments of hydrogen carriers for storage and compression and in addition give an overview of the different research activities in this field.

Chemical looping combustion (CLC) is a promising method for power production with integrated CO₂ capture with almost no direct energy penalty. When integrated into a natural gas combined cycle (NGCC) plant however CLC imposes a large indirect energy penalty because the maximum achievable reactor temperature is far below the firing temperature of state-of-the-art gas turbines. This study presents a techno-economic assessment of a CLC plant that circumvents this limitation via an added combustor after the CLC reactors. Without the added combustor the energy penalty amounts to 11.4%-points causing a high CO₂ avoidance cost of $117.3/ton which is more expensive than a conventional NGCC plant with post-combustion capture ($93.8/ton) with an energy penalty of 8.1%-points. This conventional CLC plant would also require a custom gas turbine. With an added combustor fired by natural gas a standard gas turbine can be deployed and CO2 avoidance costs are reduced to $60.3/ton mainly due to a reduction in the energy penalty to only 1.4%-points. However due to the added natural gas combustion after the CLC reactor CO₂ avoidance is only 52.4%. Achieving high CO₂ avoidance requires firing with clean hydrogen instead increasing the CO₂ avoidance cost to $96.3/ton when a hydrogen cost of $15.5/GJ is assumed. Advanced heat integration could reduce the CO₂ avoidance cost to $90.3/ton by lowering the energy penalty to only 0.6%-points. An attractive alternative is therefore to construct the plant for added firing with natural gas and retrofit the added combustor for hydrogen firing when CO₂ prices reach very high levels.

Among the several typologies of storage technologies mainly on different physical principles (mechanical electrical and chemical) hydrogen produced by power to gas (P2G) from renewable energy sources complies with chemical storage principle and is based on the conversion of electrical energy into chemical energy by means of the electrolysis of water which does not produce any toxic or climate-relevant emission. This paper aims to pinpoint the potential uses of renewable hydrogen storage systems in Europe analysing current and potential locations regulatory framework governments’ outlooks economic issues and available renewable energy amounts. The expert opinion survey already used in many research articles on different topics including energy has been selected as an effective method to produce realistic results. The obtained results highlight strategies and actions to optimize the storage of hydrogen produced by renewables to face varying electricity demand and generation-driven fluctuations reducing the negative effects of the increasing share of renewables in the energy mix of European Countries.

Variable renewable energy (VRE) is expected to play a major role in the decarbonization of the electricity sector. However decarbonization via VRE requires a fleet of flexible dispatchable plants with low CO2 emissions to supply clean power during times with limited wind and sunlight. These plants will need to operate at reduced capacity factors with frequent ramps in electricity output posing techno-economic challenges. This study therefore presents an economic assessment of a new near-zero emission power plant designed for this purpose. The gas switching reforming combined cycle (GSR-CC) plant can produce electricity during times of low VRE output and hydrogen during times of high VRE output. This product flexibility allows the plant to operate continuously even when high VRE output makes electricity production uneconomical. Although the CO2 avoidance cost of the GSR-CC plant (€61/ton) was similar to the benchmark post-combustion CO2 capture plant under baseload operation GSR-CC clearly outperformed the benchmark in a more realistic scenario where continued VRE expansion forces power plants into mid-load operation (45% capacity factor). In this scenario GSR-CC promises a 5 %-point higher annualized investment return than the post-combustion benchmark. GSR-CC therefore appears to be a promising concept for a future scenario with high VRE market share and CO2 prices provided that a large market for clean hydrogen is established.