Japan
Quantitative Evaluations of Hydrogen Diffusivity in V-X (X = Cr, Al, Pd) Alloy Membranes Based on Hydrogen Chemical Potential
Jan 2021
Publication
Vanadium (V) has higher hydrogen permeability than Pd-based alloy membranes but exhibits poor resistance to hydrogen-induced embrittlement. The alloy elements are added to reduce hydrogen solubility and prevent hydrogen-induced embrittlement. To enhance hydrogen permeability the alloy elements which improve hydrogen diffusivity in V are more suitable. In the present study hydrogen diffusivity in V-Cr V-Al and V-Pd alloy membranes was investigated in view of the hydrogen chemical potential and compared with the previously reported results of V-Fe alloy membranes. The additions of Cr and Fe to V improved the mobility of hydrogen atoms. In contrast those of Al and Pd decreased hydrogen diffusivity. The first principle calculations revealed that the hydrogen atoms cannot occupy the first-nearest neighbour T sites (T1 sites) of Al and Pd in the V crystal lattice. These blocking effects will be a dominant contributor to decreasing hydrogen diffusivity by the additions of Al and Pd. For V-based alloy membranes Fe and Cr are more suitable alloy elements compared with Al and Pd in view of hydrogen diffusivity.
Charge Carrier Mapping for Z-scheme Photocatalytic Water-splitting Sheet via Categorization of Microscopic Time-resolved Image Sequences
Jun 2021
Publication
Photocatalytic water splitting system using particulate semiconductor materials is a promising strategy for converting solar energy into hydrogen and oxygen. In particular visible-light-driven ‘Z-scheme’ printable photocatalyst sheets are cost-effective and scalable. However little is known about the fundamental photophysical processes which are key to explaining and promoting the photoactivity. Here we applied the pattern-illumination time-resolved phase microscopy for a photocatalyst sheet composed of Mo-doped BiVO4 and Rh-doped SrTiO3 with indium tin oxide as the electron mediator to investigate photo-generated charge carrier dynamics. Using this method we successfully observed the position- and structure-dependent charge carrier behavior and visualized the active/inactive sites in the sheets under the light irradiation via the time sequence images and the clustering analysis. This combination methodology could provide the material/synthesis optimization methods for the maximum performance of the photocatalyst sheets.
Materials Towards Carbon-free, Emission-free and Oil-free Mobility: Hydrogen Fuel-cell Vehicles—Now and in the Future
Jul 2010
Publication
In the past material innovation has changed society through new material-induced technologies adding a new value to society. In the present world engineers and scientists are expected to invent new materials to solve the global problem of climate change. For the transport sector the challenge for material engineers is to change the oil-based world into a sustainable world. After witnessing the recent high oil price and its adverse impact on the global economy it is time to accelerate our efforts towards this change.
Industries are tackling global energy issues such as oil and CO2 as well as local environmental problems such as NOx and particulate matter. Hydrogen is the most promising candidate to provide carbon-free emission-free and oil-free mobility. As such engineers are working very hard to bring this technology into the real society. This paper describes recent progress of vehicle technologies as well as hydrogen-storage technologies to extend the cruise range and ensure the easiness of refuelling and requesting material scientists to collaborate with industry to fight against global warming.
Link to document download on Royal Society Website
Industries are tackling global energy issues such as oil and CO2 as well as local environmental problems such as NOx and particulate matter. Hydrogen is the most promising candidate to provide carbon-free emission-free and oil-free mobility. As such engineers are working very hard to bring this technology into the real society. This paper describes recent progress of vehicle technologies as well as hydrogen-storage technologies to extend the cruise range and ensure the easiness of refuelling and requesting material scientists to collaborate with industry to fight against global warming.
Link to document download on Royal Society Website
The Effect of Graphite Size on Hydrogen Absorption and Tensile Properties of Ferritic Ductile Cast Iron
Jun 2019
Publication
Ductile cast iron (DCI) is one of prospective materials used for the hydrogen equipment because of low-cost good workability and formability. The wide range of mechanical properties of DCI is obtained by controlling microstructural factors such as graphite size volume fraction of graphite matrix structure and so on. Therefore it is important to find out an optimal microstructural condition that is less susceptible to hydrogen embrittlement. In this study the effects of graphite size on the hydrogen absorption capability and the hydrogen-induced ductility loss of ferritic DCI were investigated.<br/>Several kinds of ferritic DCIs with a different graphite diameter of about 10 µm - 30 µm were used for the tensile test and the hydrogen content measurement. Hydrogen charging was performed prior to the tensile test by exposing a specimen to high-pressure hydrogen gas. Then the tensile test was performed in air at room temperature. The hydrogen content of a specimen was measured by a thermal desorption analyzer.<br/>It was found that the amount of hydrogen stored in DCI was dependent on the graphite size. As the graphite diameter increased the hydrogen content sharply increased at a certain graphite diameter and then it became nearly constant irrespective of increase in graphite diameter. In other words there was the critical graphite diameter that significantly changed the hydrogen absorption capability. The ductility was decreased by hydrogen and the hydrogen-induced ductility loss was dependent on the hydrogen content. Therefore the hydrogen embrittlement of DCI became remarkable when the graphite size was larger than the critical value.
Unusual Hydrogen Implanted Gold with Lattice Contraction at Increased Hydrogen Content
Mar 2021
Publication
The experimental evidence for the contraction of volume of gold implanted with hydrogen at low doses is presented. The contraction of lattice upon the addition of other elements is very rare and extraordinary in the solid-state not only for gold but also for many other solids. To explain the underlying physics the pure kinetic theory of absorption is not adequate and the detailed interaction of hydrogen in the lattice needs to be clarified. Our analysis points to the importance of the formation of hydride bonds in a dynamic manner and explains why these bonds become weak at higher doses leading to the inverse process of volume expansion frequently seen in metallic hydrogen containers.
The Study on Permissible Value of Hydrogen Gas Concentration in Purge Gas of Fuel Cell Vehicles
Sep 2019
Publication
Ignition conditions and risks of ignition on a permissible value of hydrogen concentration in purge gas prescribed by HFCV-GTR were reevaluated. Experiments were conducted to investigate burning behavior and thermal influence of continuous evacuation of hydrogen under continuous purge of air / hydrogen premixed gas which is close to an actual purge condition of FCV and thermal evacuation of hydrogen. As a result of the re-evaluation it was shown from the viewpoint of safety that the permissible value of hydrogen concentration in purge gas prescribed by the current HFCV GTR is appropriate.
Comparative Technical and Economic Analyses of Hydrogen-Based Steel and Power Sectors
Mar 2024
Publication
Decarbonizing the current steel and power sectors through the development of the hydrogen direct-reduction iron ore–electric arc furnace route and the 100% hydrogen-fired gas turbine cycle is crucial. The current study focuses on three clusters of research works. The first cluster covers the investigation of the mass and energy balance of the route and the subsequent application of these values in experiments to optimize the reduction yield of iron ore. In the second cluster the existing gas turbine unit was selected for the complete replacement of natural gas with hydrogen and for finding the most optimal mass and energy balance in the cycle through an Aspen HYSYS model. In addition the chemical kinetics in the hydrogen combustion process were simulated using Ansys Chemkin Pro to research the emissions. In the last cluster a comparative economic analysis was conducted to identify the levelized cost of production of the route and the levelized cost of electricity of the cycle. The findings in the economic analysis provided good insight into the details of the capital and operational expenditures of each industrial sector in understanding the impact of each kg of hydrogen consumed in the plants. These findings provide a good basis for future research on reducing the cost of hydrogen-based steel and power sectors. Moreover the outcomes of this study can also assist ongoing large-scale hydrogen and ammonia projects in Uzbekistan in terms of designing novel hydrogen-based industries with cost-effective solutions.
Fabrication of CdS/β-SiC/TiO2 Tri-composites That Exploit Hole- and Electron-transfer Processes for Photocatalytic Hydrogen Production Under Visible Light
Dec 2017
Publication
In this work CdS/SiC/TiO2 tri-composite photocatalysts that exploit electron- and hole-transfer processes were fabricated using an easy two-step method in the liquid phase. The photocatalyst with a 1:1:1 M ratio of CdS/SiC/TiO2 exhibited a rate of hydrogen evolution from an aqueous solution of sodium sulfite and sodium sulfide under visible light of 137 μmol h−1 g−1 which is 9.5 times that of pure CdS. β-SiC can act as a sink for the photogenerated holes because the valence band level of β-SiC is higher than the corresponding bands in CdS and TiO2. In addition the level of the conduction band of TiO2 is lower than those of CdS and β-SiC so TiO2 can act as the acceptor of the photogenerated electrons. Our results demonstrate that hole transfer and absorption in the visible light region lead to an effective hydrogen-production scheme.
Evaluation of Safety Measures of a Hydrogen Fueling Station Using Physical Modeling
Oct 2018
Publication
Hydrogen fueling stations are essential for operating fuel cell vehicles. If multiple safety measures in a hydrogen fueling station fail simultaneously it could lead to severe consequences. To analyze the risk of such a situation we developed a physical model of a hydrogen fueling station which when using the temperature pressure and flow rate of hydrogen could be simulated under normal and abnormal operating states. The physical model was validated by comparing the analytical results with the experimental results of an actual hydrogen fueling station. By combining the physical model with a statistical method we evaluated the significance of the safety measures in the event wherein multiple safety measures fail simultaneously. We determined the combinations of failures of safety measures that could lead to accidents and suggested a measure for preventing and mitigating the accident scenario.
Crack Size Dependency of Shear-mode Fatigue Threshold in Bearing Steel Subjected to Continuous Hydrogen Charging
Jun 2019
Publication
Premature delamination failure characterized by the white structure flaking (WSF) or the white etching crack (WEC) often occurs in rolling element bearings and it deteriorates the durability of bearing substantially. It is known that this failure is caused by shear-mode (Mode II and Mode III) crack growth in conjunction with evolution and invasion of hydrogen into material during operation. To ensure the structural integrity associated with rolling element bearing it is important to clarify the effect of hydrogen on the shear-mode fatigue crack growth behavior near the threshold level.<br/>In our previous study the effect of hydrogen on the shear-mode fatigue crack growth behavior in a bearing steel of JIS SUJ2 was examined near the threshold level. Consequently it was shown that the threshold stress intensity factor (SIF) range for shear-mode fatigue crack growth decreased significantly by action of hydrogen. However the investigation was made only for a crack with a surface length of about 900 mm. To thoroughly understand the critical condition for delamination failure it is important to investigate the crack size dependency of the threshold level for a shear-mode small fatigue crack in the presence of hydrogen. In the present study correspondingly the threshold SIF ranges for a shear-mode crack with different length were additionally measured in the same material by using a novel technique that enables continuous charging of hydrogen in a specimen during long-term fatigue test. Then a clear reduction in crack growth rate and a crack size dependency of the threshold SIF range were observed under the environmental condition of continuous hydrogen charging.
A Fully Renewable and Efficient Backup Power System with a Hydrogen-biodiesel-fueled IC Engine
Jan 2019
Publication
Renewable energy is free abundant clean and could contribute towards a significant reduction of the global warming emissions. It is massively introduced as a source of electricity production across the globe and is expected to become the primary source of energy within the following decades. However despite the naturally replenished energy the supply is not always available. For this reason it is necessary at times of excess energy any surplus quantity to be sufficiently captured stored and later used when a deficit occurs. In this paper an overview of a backup power system operating with a hydrogen-biodiesel dual-fuel internal combustion engine is provided. The system is utilizing the organic chemical hydride method for safe hydrogen storage and transportation. The high energy content of hydrogen stored in the form of an organic hydride under ambient conditions makes it an ideal energy backup medium for large-scale and long-term applications. The research work focusses on the operation and emissions output of the dual-fuel internal combustion engine running on fully renewable fuels and the results are compared with the conventional petroleum-derived diesel engine. Biodiesel-hydrogen operation shows significant benefits in the reduction of carbon and soot emissions but deteriorates the NOx formation compared to the conventional diesel-powered engines. The operation of the engine at high loads can provide high exhaust thermal energy while alternative combustion strategies are necessary to be implemented at low load conditions for the optimum operation of the backup power system.
The Residual Strength of Automotive Hydrogen Cylinders After Exposure to Flames
Sep 2017
Publication
Fuel cell vehicles and some compressed natural gas vehicles are equipped with carbon fiber reinforced plastic (CFRP) composite cylinders. Each of the cylinders has a pressure relief device designed to detect heat and release the internal gas to prevent the cylinder from bursting in a vehicle fire accident. Yet in some accident situations the fire may be extinguished before the pressure relief device is activated leaving the high-pressure fuel gas inside the fire-damaged cylinder. To handle such a cylinder safely after an accident it is necessary that the cylinder keeps a sufficient post-fire strength against its internal gas pressure but in most cases it is difficult to accurately determine cylinder strength at the accident site. One way of solving this problem is to predetermine the post-fire burst strengths of cylinders by experiments. In this study automotive CFRP cylinders having no pressure relief device were exposed to a fire to the verge of bursting; then after the fire was extinguished the residual burst strengths and the overall physical state of the test cylinders were examined. The results indicated that the test cylinders all recorded a residual burst strength at least twice greater than their internal gas pressure for tested cylinders with new cylinder burst to nominal working pressure in the range 2.67–4.92 above the regulated ratio of 2.25.
Simulation of a Multi-Functional Energy System for Cogeneration of Steam, Power and Hydrogen in a Coke Making Plant
Mar 2013
Publication
In this paper a multifunctional energy system (MES) is proposed for recovering energy from the extra of coke oven gas (COG) which is usually flared or vented out as a waste stream in coke making plants. The proposed system consists of a pressure swing adsorption (PSA) unit for extracting some of the hydrogen from COG a gas turbine for producing heat and power from PSA offgas and a heat recovery steam generator (HRSG) for generating the steam required by the plant's processes. o assess the performance of the system practically simulations are carried out on the basis of the design and operational conditions of Zarand Coke Making Plant in Iran. The results indicate that by utilizing about 4.39 tons of COG per hour 6.5 MW of net electric power can be approximately produced by the gas turbine which can supply the coke making plant's total electrical power demand. Furthermore through recovering heat from gas turbine's exhaust close to 57% of the plant's steam demand can be supplied by the HRSG unit. It is also found that around 350 kilograms per hour of nearly pure hydrogen (99.9% purity) at 200 bar can be produced by the PSA unit. According to the sensitivity analysis results if the hydrogen content of the coke oven gas decreases by about 10% the gross power output of the gas turbine also declines by around 5.2% due to the reduction of LHV of the PSA offgas. Moreover economic evaluation of the system shows that the payback period of the investment which is estimated at 36.1 M$ is about 5.5 years. The net present value (NPV) and internal rate of return on investment (ROI) are calculated to be 17.6% and 43.3 M$ respectively.
Removing the Bottleneck on Wind Power Potential to Create Liquid Fuels from Locally Available Biomass
Jun 2021
Publication
In order to reduce global greenhouse gas emissions renewable energy technologies such as wind power and solar photovoltaic power systems have recently become more widespread. However Japan as a nation faces high reliance on imported fossil fuels for electricity generation despite having great potential for further renewable energy development. The focus of this study examines untapped geographical locations in Japan’s northern most prefecture Hokkaido that possess large wind power potential. The possibility of exploiting this potential for the purpose of producing green hydrogen is explored. In particular its integration with a year-round conversion of Kraft lignin into bio-oil from nearby paper pulp mills through a near critical water depolymerization process is examined. The proposed bio-oil and aromatic chemical production as well as the process’ economics are calculated based upon the total available Kraft lignin in Hokkaido including the magnitude of wind power capacity that would be required for producing the necessary hydrogen for such a large-scale process. Green hydrogen integration with other processes in Japan and in other regions is also discussed. Finally the potential benefits and challenges are outlined from an energy policy point-of-view.
Impact of Hydrogen Fuel for CO2 Emission Reduction in Power Generation Sector in Japan
Jun 2017
Publication
Japan’s energy consumption derives mostly from fossil fuels which are un-secure and release a much greenhouse gas emissions. To meet goals of reducing GHG hydrogen gas can be utilized in power generation in hydrogen fired and firing / co-combustion power plants. This paper analyses the impact of hydrogen in the power generation sector using the MARKAL-TIMES Japan optimization model framework. Two models are used: a base scenario without hydrogen and hydrogen scenario in which hydrogen is supplied from 2020 onwards. In the hydrogen scenario other processes which are normally supplied by natural gas are reduced because the gas is instead used to generate power. Adding hydrogen to the energy supply leads to a decrease in projected use of fossil fuels. The hydrogen scenario produces fewer emissions than the base scenario; by 2050 the hydrogen scenario’s estimated 388 metric tons of CO2 emissions is over 250 tons less than the base scenario’s emissions of 588 metric tons.
Near-term Location of Hydrogen Refueling Stations in Yokohama City from the Perspective of Safety
Sep 2019
Publication
The roll-out of hydrogen refuelling stations is a key step in the transition to a hydrogen economy. Since Japan has been shifting from the demonstration stage to the implementation stage of a hydrogen economy a near-term city-level roll-out plan is required. The aim of this study is to plan near-term locations for building hydrogen refuelling stations in Yokohama City from a safety perspective. Our planning provides location information for hydrogen refuelling stations in Yokohama City for the period 2020–2030. Mobile type and parallel siting type refuelling stations have been considered in our planning and locations were determined by matching supply and demand to safety concerns. Supply and demand were estimated from hybrid vehicle ownership data and from space availability in existing gas stations. The results reaffirmed the importance of hydrogen station location planning and showed that use of mobile type stations is a suitable solution in response to the uncertain fuel cell vehicle fuel demand level during the implementation stage of a hydrogen economy.
Marked Degradation of Tensile Properties Induced by Plastic Deformation after Interactions between Strain-Induced Martensite Transformation and Hydrogen for Type 316L Stainless Steel
Jul 2020
Publication
Marked degradation of tensile properties induced by plastic deformation after dynamic interactions between strain-induced martensite transformation and hydrogen has been investigated for type 316L stainless steel by hydrogen thermal desorption analysis. Upon modified hydrogen charging reported previously the amount of hydrogen desorbed in the low temperature range increases; the degradation of tensile properties induced by interactions between plastic deformation and hydrogen at 25 °C or induced by interactions between martensite transformation and hydrogen at −196 °C occurs even for the stainless steel with high resistance to hydrogen embrittlement. The hydrogen thermal desorption behavior is changed by each interaction suggesting changes in hydrogen states. For specimen fractured at 25 °C the facet-like morphology and transgranular fracture are observed on the outer part of the fracture surface. At −196 °C a quasi-cleave fracture is observed at the initiation area. Modified hydrogen charging significantly interacts both plastic deformation and martensite transformation eventually enhancing the degradation of tensile properties. Upon plastic deformation at 25° C after the interactions between martensite transformation and hydrogen by straining to 0.2 at −196 °C cracks nucleate in association with martensite formed by the interactions at −196 °C and marked degradation of tensile properties occurs. It is likely that the interactions between martensite transformation and hydrogen induce damage directly related to the degradation thereby affecting subsequent deformation. Upon dehydrogenation after the interactions between the martensite transformation and hydrogen no degradation of tensile properties is observed. The damage induced by the interactions between martensite transformation and hydrogen probably changes to harmless defects during dehydrogenation.
Characterization of Hydrogen Transport Accidents in Japan Based on Network Theory
Sep 2019
Publication
Realizing the hydrogen economy in Japan entails a risk assessment of its domestic hydrogen supply especially hydrogen transport by road. The first step of the risk assessment is to characterize the hydrogen transport accidents from different energy carriers. However it is difficult to characterize the accidents because hydrogen transport systems have not been fully implemented in Japan. The aim of this study is to characterize the hydrogen transport accidents from different energy carriers in Japan. We studied three major energy carriers namely compressed hydrogen liquefied hydrogen and liquid organic hydride. The accident networks based on network theory were constructed to capture the comprehensive accident processes and quantitatively characterized the hydrogen transport accidents from different energy carriers. The results clarified the differences and similarities in the accident process amongst the energy carriers. Furthermore key accident events were identified. This study contributes to the development of comprehensive hydrogen transport accident scenarios for risk assessment.
Large-Scale Hydrogen Deflagrations and Detonations
Sep 2005
Publication
Large-scale deflagration and detonation experiments of hydrogen and air mixtures provide fundamental data needed to address accident scenarios and to help in the evaluation and validation of numerical models. Several different experiments of this type were performed. Measurements included flame front time of arrival (TOA) using ionization probes blast pressure heat flux high-speed video standard video and infrared video. The large-scale open-space tests used a hemispherical 300-m3 facility that confined the mixture within a thin plastic tent that was cut prior to initiating a deflagration. Initial homogeneous hydrogen concentrations varied from 15% to 30%. An array of large cylindrical obstacles was placed within the mixture for some experiments to explore turbulent enhancement of the combustion. All tests were ignited at the bottom center of the facility using either a spark or in one case a small quantity of high explosive to generate a detonation. Spark-initiated deflagration tests were performed within the tunnel using homogeneous hydrogen mixtures. Several experiments were performed in which 0.1 kg and 2.2 kg of hydrogen were released into the tunnel with and without ventilation. For some tunnel tests obstacles representing vehicles were used to investigate turbulent enhancement. A test was performed to investigate any enhancement of the deflagration due to partial confinement produced by a narrow gap between aluminium plates. The attenuation of a blast wave was investigated using a 4-m-tall protective blast wall. Finally a large-scale hydrogen jet experiment was performed in which 27 kg of hydrogen was released vertically into the open atmosphere in a period of about 30 seconds. The hydrogen plume spontaneously ignited early in the release.
Numerical Simulation of Hydrogen Explosion Tests with a Barrier Wall for Blast Mitigation
Sep 2005
Publication
We have investigated hydrogen explosion risk and its mitigation focusing on compact hydrogen refuelling stations in urban areas. In this study numerical analyses were performed of hydrogen blast propagation and the structural behaviour of barrier walls. Parametric numerical simulations of explosions were carried out to discover effective shapes for blast-mitigating barrier walls. The explosive source was a prismatic 5.27 m3 volume that contained 30% hydrogen and 70% air. A reinforced concrete wall 2 m tall by 10 m wide and 0.15 m thick was set 2 or 4 m away from the front surface of the source. The source was ignited at the bottom centre by a spark for the deflagration case and 10 g of C-4 high explosive for two detonation cases. Each of the tests measured overpressures on the surfaces of the wall and on the ground displacements of the wall and strains of the rebar inside the wall. The blast simulations were carried out with an in-house CFD code based on the compressive Euler equation. The initial energy estimated from the volume of hydrogen was a time-dependent function for the deflagration and was released instantaneously for the detonations. The simulated overpressures were in good agreement with test results for all three test cases. DIANA a finite element analysis code released by TNO was used for the structural simulations of the barrier wall. The overpressures obtained by the blast simulations were used as external forces. The analyses simulated the displacements well but not the rebar strains. The many shrinkage cracks that were observed on the walls some of which penetrated the wall could make it difficult to simulate the local behaviour of a wall with high accuracy and could cause strain gages to provide low-accuracy data. A parametric study of the blast simulation was conducted with several cross-sectional shapes of barrier wall. A T-shape and a Y-shape were found to be more effective in mitigating the blast.
Fundamental Study on Hydrogen Low-NOx Combustion Using Exhaust Gas Self-Recirculation
Jan 2022
Publication
Hydrogen is expected to be a next-generation energy source that does not emit carbon dioxide but when used as a fuel the issue is the increase in the amount of NOx that is caused by the increase in flame temperature. In this study we experimentally investigated NOx emissions rate when hydrogen was burned in a hydrocarbon gas burner which is used in a wide temperature range. As a result of the experiments the amount of NOx when burning hydrogen in a nozzle mixed burner was twice as high as when burning city gas. However by increasing the flow velocity of the combustion air the amount of NOx could be reduced. In addition by reducing the number of combustion air nozzles rather than decreasing the diameter of the air nozzles a larger recirculation flow could be formed into the furnace and the amount of NOx could be reduced by up to 51%. Furthermore the amount of exhaust gas recirculation was estimated from the reduction rate of NOx and the validity was confirmed by the relationship between adiabatic flame temperature and NOx calculated from the equilibrium calculation by chemical kinetics simulator software.
Evaluation of Metal Materials for Hydrogen Fuel Stations
Sep 2005
Publication
Under government funded project: "Development for Safe Utilization and Infrastructure of Hydrogen" entrusted by New Energy and Industrial Technology Development Organization (NEDO) special material testing equipment with heavy walled pressure vessel under 45MPa gaseous hydrogen is facilitated. Tensile properties strain controlled low-cycle and high-cycle fatigue and fatigue crack growth tests on CrMo steel (SCM435 (JIS G 4105)) which will be applied for the storage gas cylinders in Japanese hydrogen fuel stations are investigated. The results of the tensile tests under 45MPa ultra high purity hydrogen gas (O2<1ppm) at room temperature shows that there are no difference in yield and maximum tensile strength with those tested in air. However the reduced ductilities with brittle fracture surface were observed which indicates the occurrence of hydrogen environment embrittlement. It was also found by tensile tests that the embrittling origin is not only caused by machined traces on surface but also by the non-metallic inclusions dispersed on surface. Further discussions on surface treatment effects will be presented. In low cycle fatigue tests considerable reductions in cycles to failure in 45MPa ultra high purity hydrogen gas were observed. However there are tendencies that the effect of hydrogen environment embrittlement becomes not so significant as the plastic strain range decreases. It was demonstrated that there was no effect of hydrogen on fatigue limit and this implies that CrMo gas cylinders can be operated in limited fatigue safe condition. Another series of hydrogen test results temperature effect fatigue crack growth rate delayed fracture test using wedge opening loaded specimens and fatigue test of CrMo gas cylinders under repeated internal pressure with artificial crack will be presented.
Experimental Study of Hydrogen Release Accidents in a Vehicle Garage
Sep 2009
Publication
Storing a hydrogen fuel-cell vehicle in a garage poses a potential safety hazard because of the accidents that could arise from a hydrogen leak. A series of tests examined the risk involved with hydrogen releases and deflagrations in a structure built to simulate a one-car garage. The experiments involved igniting hydrogen gas that was released inside the structure and studying the effects of the deflagrations. The “garage” measured 2.72 m high 3.64 m wide and 6.10 m long internally and was constructed from steel using a reinforced design capable of withstanding a detonation. The front face of the garage was covered with a thin transparent plastic film. Experiments were performed to investigate extended-duration (20–40 min) hydrogen leaks. The effect that the presence of a vehicle in the garage has on the deflagration was also studied. The experiments examined the effectiveness of different ventilation techniques at reducing the hydrogen concentration in the enclosure. Ventilation techniques included natural upper and lower openings and mechanical ventilation systems. A system of evacuated sampling bottles was used to measure hydrogen concentration throughout the garage prior to ignition and at various times during the release. All experiments were documented with standard and infrared (IR) video. Flame front propagation was monitored with thermocouples. Pressures within the garage were measured by four pressure transducers mounted on the inside walls of the garage. Six free-field pressure transducers were used to measure the pressures outside the garage.
Experimental Study on Hydrogen Explosions in a Full-scale Hydrogen Filling Station Model
Sep 2005
Publication
In order for fuel cell vehicles to develop a widespread role in society it is essential that hydrogen refuelling stations become established. For this to happen there is a need to demonstrate the safety of the refuelling stations. The work described in this paper was carried out to provide experimental information on hydrogen outflow dispersion and explosion behaviour. In the first phase homogeneous hydrogen-air-mixtures of a known concentration were introduced into an explosion chamber and the resulting flame speed and overpressures were measured. Hydrogen concentration was the dominant factor influencing the flame speed and overpressure. Secondly high-pressure hydrogen releases were initiated in a storage room to study the accumulation of hydrogen. For a steady release with a constant driving pressure the hydrogen concentration varied as the inlet airflow changed depending on the ventilation area of the room the external wind conditions and also the buoyancy induced flows generated by the accumulating hydrogen. Having obtained this basic data the realistic dispersion and explosion experiments were executed at full-scale in the hydrogen station model. High-pressure hydrogen was released from 0.8-8.0mm nozzle at the dispenser position and inside the storage room in the full-scale model of the refuelling station. Also the hydrogen releases were ignited to study the overpressures that can be generated by such releases. The results showed that overpressures that were generated following releases at the dispenser location had a clear correlation with the time of ignition distance from ignition point.
Study of Hydrogen Diffusion and Deflagration in a Closed System
Sep 2007
Publication
A total of 12 ventilation experiments with various combinations of hydrogen release rates and ventilation speeds were performed in order to study how ventilation speed and release rate effect the hydrogen concentration in a closed system. The experiential facility was constructed out of steel plates and beams in the shape of a rectangular enclosure. The volume of the test facility was about 60m3. The front face of the enclosure was covered by a plastic film in order to allow visible and infrared cameras to capture images of the flame. The inlet and outlet vents were located on the lower front face and the upper backside panel respectively. Hydrogen gas was released toward the ceiling from the center of the floor. The hydrogen gas was released at constant rate in each test. The hydrogen release rate ranged from 0.002 m3/s to 0.02 m3/s. Ventilation speeds were 0.1 0.2 and 0.4 m3/s respectively. Ignition was attempted at the end of the hydrogen release by using multiple continuous spark ignition modules on the ceiling and next to the release point. Time evolution of hydrogen concentration was measured using evacuated sample bottles. Overpressure and impulse inside and outside the facility were also measured. The mixture was ignited by a spark ignition module mounted on the ceiling in eight of eleven tests. In the other three tests the mixture was ignited by spark ignition modules mounted next to the nozzle. Overpressures generated by the hydrogen deflagration in most of these tests were low and represented a small risk to people or property. The primary risk associated with the hydrogen deflagrations studied in these tests was from the fire. The maximum concentration is proportional to the ratio of the hydrogen release rate to the ventilation speed within the range of parameters tested. Therefore a required ventilation speed can be estimated from the assumed hydrogen leak rate within the experimental conditions described in this paper.
CFD Simulation on Diffusion of Leaked Hydrogen Caused by Vehicle Accident in Tunnels
Sep 2005
Publication
Hydrogen fuel cell vehicles are expected to come into widespread use in the near future. Accordingly many hydrogen carrying vehicles will begin to pass through tunnels. It is therefore important to predict whether risk from leaked hydrogen accidents in tunnels can be avoided. CFD simulation was carried out on diffusion of leaked hydrogen in tunnels. Three areas of tunnels were chosen for study. One is the typical longitudinal and lateral areas of tunnels and the others are underground ventilation facilities and electrostatic dust collectors which were simulated with an actual tunnel. The amount of hydrogen leaked was 60m3 (approximately 5.08 kg) which corresponds to the amount necessary for future fuel cell vehicles to achieve their desired running distance. Analytical periods were the time after leaks began until regions of hydrogen above the low flammability limit had almost disappeared or thirty minutes. We found that leaked hydrogen is immediately carried away from leaking area under existing ventilation conditions. We also obtained basic data on behaviour of leaked hydrogen.
Energy Modeling Approach to the Global Energy-mineral Nexus: Exploring Metal Requirements and the Well-below 2 °C Target with 100 Percent Renewable Energy
Jun 2018
Publication
Detailed analysis of pathways to future sustainable energy systems is important in order to identify and overcome potential constraints and negative impacts and to increase the utility and speed of this transition. A key aspect of a shift to renewable energy technologies is their relatively higher metal intensities. In this study a bottom-up cost-minimizing energy model is used to calculate aggregate metal requirements in different energy technology including hydrogen and climate policy scenarios and under a range of assumptions reflecting uncertainty in future metal intensities recycling rate and life time of energy technologies. Metal requirements are then compared to current production rates and resource estimates to identify potentially “critical” metals. Three technology pathways are investigated: 100 percent renewables coal & nuclear and gas & renewables each under the two different climate policies: net zero emissions satisfying the well-below 2 °C target and business as usual without carbon constraints resulting together in six scenarios. The results suggest that the three different technology pathways lead to an almost identical degree of warming without any climate policy while emissions peaks within a few decades with a 2 °C policy. The amount of metals required varies significantly in the different scenarios and under the various uncertainty assumptions. However some can be deemed “critical” in all outcomes including Vanadium. The originality of this study lies in the specific findings and in the employment of an energy model for the energy-mineral nexus study to provide better understanding for decision making and policy development.
Thermodynamic Assessment of a Solar-Driven Integrated Membrane Reactor for Ethanol Steam Reforming
Nov 2020
Publication
To efficiently convert and utilize intermittent solar energy a novel solar-driven ethanol steam reforming (ESR) system integrated with a membrane reactor is proposed. It has the potential to convert low-grade solar thermal energy into high energy level chemical energy. Driven by chemical potential hydrogen permeation membranes (HPM) can separate the generated hydrogen and shift the ESR equilibrium forward to increase conversion and thermodynamic efficiency. The thermodynamic and environmental performances are analyzed via numerical simulation under a reaction temperature range of 100–400 ◦C with permeate pressures of 0.01–0.75 bar. The highest theoretical conversion rate is 98.3% at 100 ◦C and 0.01 bar while the highest first-law efficiency solar-to-fuel efficiency and exergy efficiency are 82.3% 45.3% and 70.4% at 215 ◦C and 0.20 bar. The standard coal saving rate (SCSR) and carbon dioxide reduction rate (CDRR) are maximums of 101 g·m−2 ·h −1 and 247 g·m−2 ·h −1 at 200 ◦C and 0.20 bar with a hydrogen generation rate of 22.4 mol·m−2 ·h −1 . This study illustrates the feasibility of solar-driven ESR integrated with a membrane reactor and distinguishes a novel approach for distributed hydrogen generation and solar energy utilization and upgradation.
Precooling Temperature Relaxation Technology in Hydrogen Refueling for Fuel-Cell Vehicles
Aug 2021
Publication
The dissemination of fuel-cell vehicles requires cost reduction of hydrogen refueling stations. The temperature of the supplied hydrogen has currently been cooled to approximately 40 C. This has led to larger equipment and increased electric power consumption. This study achieves a relaxation of the precooling temperature to the 20 C level while maintaining the refueling time. (1) Adoption of an MC formula that can flexibly change the refueling rate according to the precooling temperature. (2) Measurement of thermal capacity of refueling system parts and re-evaluation. Selection from multiple refueling control maps according to the dispenser design (Mathison et al. 2015). (3) Calculation of the effective thermal capacity and reselection of the map in real time when the line is cooled from refueling of the previous vehicle (Mathison and Handa 2015). (4) Addition of maps in which the minimum assumed pressures are 10 and 15 MPa. The new method is named MC Multi Map
Current Research and Development Activities on Fission Products and Hydrogen Risk after the Accident at Fukushima Daiiichi Nuclear Power Station
Jan 2015
Publication
After the Fukushima Daiichi nuclear power plant (NPP) accident new regulatory requirements were enforced in July 2013 and a backfit was required for all existing nuclear power plants. It is required to take measures to prevent severe accidents and mitigate their radiological consequences. The Regulatory Standard and Research Department Secretariat of Nuclear Regulation Authority (S/NRA/R) has been conducting numerical studies and experimental studies on relevant severe accident phenomena and countermeasures. This article highlights fission product (FP) release and hydrogen risk as two major areas. Relevant activities in the S/NRA/R are briefly introduced as follows: 1. For FP release: Identifying the source terms and leak mechanisms is a key issue from the viewpoint of understanding the progression of accident phenomena and planning effective countermeasures that take into account vulnerabilities of containment under severe accident conditions. To resolve these issues the activities focus on wet well venting pool scrubbing iodine chemistry (in-vessel and ex-vessel) containment failure mode and treatment of radioactive liquid effluent. 2. For hydrogen risk: because of three incidents of hydrogen explosion in reactor buildings a comprehensive reinforcement of the hydrogen risk management has been a high priority topic. Therefore the activities in evaluation methods focus on hydrogen generation hydrogen distribution and hydrogen combustion.
Hydrogen Storage Behavior of TiFe Alloy Activated by Different Methods
Feb 2021
Publication
TiFe activation for hydrogen uptake was conducted through different methods and ball milling with ethanol proved to be the most effective one. TiFe alloy after activation could absorb 1.2 wt% hydrogen at room temperature with absorption and desorption plateaus of 0.5 MPa and 0.2 MPa respectively. Investigation on microstructure and chemical state of TiFe sample after milled with ethanol suggested that the well spread metallic Ti and Fe elements helped hydrogen uptake and release. The activation of TiFe alloy by milling with ethanol was achieved at ambient conditions with ease successfully and possibly can be used for large scale production
Hydrogen - A Sustainable Energy Carrier
Jan 2017
Publication
Hydrogen may play a key role in a future sustainable energy system as a carrier of renewable energy to replace hydrocarbons. This review describes the fundamental physical and chemical properties of hydrogen and basic theories of hydrogen sorption reactions followed by the emphasis on state-of-the-art of the hydrogen storage properties of selected interstitial metallic hydrides and magnesium hydride especially for stationary energy storage related utilizations. Finally new perspectives for utilization of metal hydrides in other applications will be reviewed.
Numerical Prediction of Forced-ignition Limit in High-pressurized Hydrogen Jet Flow Through a Pinhole
Sep 2017
Publication
The numerical simulations on the high-pressure hydrogen jet are performed by using the unsteady three-dimensional compressible Navier-Stokes equations with multi-species conservation equations. The present numerical results show that the highly expanded hydrogen free jet observes and the distance between the Mach disc and the nozzle exit agrees well with the empirical equation. The time-averaged H2 concentration of the numerical simulations agrees well with the experimental data and the empirical equation. The numerical simulation of ignition in a hydrogen jet is performed to show the flame behaviour from the calculated OH iso surface. We predicted the ignition and no-ignition region from the present numerical results about the forced ignition in the high-pressurized hydrogen jet.
Numerical Investigation on the Dispersion of Hydrogen Leaking from a Hydrogen Fuel Cell Vehicle in Seaborne Transportation
Oct 2015
Publication
The International Maritime Organization under the United Nations has developed safety requirements for seaborne transportation of hydrogen fuel cell vehicles in consideration of a recent increase in such transportation. Japan has led the development of new regulations in the light of some research outcomes including numerical simulations on hydrogen dispersion in a cargo space of a vehicle carrier in case of accidental leakage of hydrogen from the vehicle. Numerical results indicate that the region of space occupied by flammable hydrogen/air mixture strongly depends on the direction of ventilation openings. These findings have contributed to the development of new international regulations.
Numerical Simulation and Experiments of Hydrogen Diffusion Behaviour for Fuel Cell Electric Vehicle
Sep 2011
Publication
Research was conducted on hydrogen diffusion behaviour to construct a simulation method for hydrogen leaks into complexly shaped spaces such as around the hydrogen tank of a fuel cell electric vehicle (FCEV). To accurately calculate the hydrogen concentration distribution in the vehicle underfloor space it is necessary to take into account the effects of hydrogen mixing and diffusion due to turbulence. The turbulence phenomena that occur in the event that hydrogen leaks into the vehicle underfloor space were classified into the three elements of jet flow wake flow and wall turbulence. Experiments were conducted for each turbulence element to visualize the flows and the hydrogen concentration distributions were measured. These experimental values were then compared with calculated values to determine the calculation method for each turbulence phenomenon. Accurate calculations could be performed by using the k-ω Shear Stress Transport (SST) model for the turbulence model in the jet flow calculations and the Reynolds Stress Model (RSM) in the wall turbulence calculations. In addition it was found that the large fluctuations produced by wake flow can be expressed by unsteady state calculations with the steady state calculation solutions as the initial values. Based on the above information simulations of hydrogen spouting were conducted for the space around the hydrogen tank of an FCEV. The hydrogen concentration calculation results matched closely with the experimental values which verified that accurate calculations can be performed even for the complex shapes of an FCEV.
Alloy Optimization for Reducing Delayed Fracture Sensitivity of 2000 MPa Press Hardening Steel
Jun 2020
Publication
Press hardening steel (PHS) is widely applied in current automotive body design. The trend of using PHS grades with strengths above 1500 MPa raises concerns about sensitivity to hydrogen embrittlement. This study investigates the hydrogen delayed fracture sensitivity of steel alloy 32MnB5 with a 2000 MPa tensile strength and that of several alloy variants involving molybdenum and niobium. It is shown that the delayed cracking resistance can be largely enhanced by using a combination of these alloying elements. The observed improvement appears to mainly originate from the obstruction of hydrogen-induced damage incubation mechanisms by the solutes as well as the precipitates of these alloying elements.
Assessment of the Contribution of Internal Pressure to the Structural Damage in a Hydrogen-charged Type 316L Austenitic Stainless Steel During Slow Strain Rate Tensile Test
Dec 2018
Publication
The aim of this study is to provide a quantification of the internal pressure contribution to the SSRT properties of H-charged Type-316L steel tested in air at room temperature. Considering pre-existing penny-shaped voids the transient pressure build-up has been simulated as well as its impact on the void growth by preforming JIc calculations. Several void distributions (size and spacing) have been considered. Simulations have concluded that there was no impact of the internal pressure on the void growth regardless the void distribution since the effective pressure was on the order of 1 MPa during the SSRT test. Even if fast hydrogen diffusion related to dislocation pipe-diffusion has been assessed as a conservative case the impact on void growth was barely imperceptible (or significantly low). The effect of internal pressure has been experimentally verified via the following conditions: (I) non-charged in vacuum; (II) H-charged in vacuum; (III) H-charged in 115-MPa nitrogen gas; (IV) non-charged in 115-MPa nitrogen gas. As a result the relative reduction in area (RRA) was 0.84 for (II) 0.88 for (III) and 1.01 for (IV) respectively. The difference in void morphology of the H-charged specimens did not depend on the presence of external pressure. These experimental results demonstrate that the internal pressure had no effect on the tensile ductility and void morphology of the H-charged specimen.
Simulation-based Safety Investigation of a Hydrogen Fueling Station with an On-site Hydrogen Production System Involving Methylcyclohexane
Jan 2017
Publication
Adequate safety measures are crucial for preventing major accidents at hydrogen fuelling stations. In particular risk analysis of the domino effect at hydrogen fuelling stations is essential because knock-on accidents are likely to intensify the consequences of a relatively small incident. Several risk assessment studies have focused on hydrogen fuelling stations but none have investigated accidental scenarios related to the domino effect at such stations. Therefore the purpose of this study is to identify a domino effect scenario analyze the scenario by using simulations and propose safety measures for preventing and mitigating of the scenario. In this hazard identification study we identified the domino effect scenario of a hydrogen fuelling station with an on-site hydrogen production system involving methylcyclohexane and investigated through simulations of the scenario. The simulations revealed that a pool fire of methylcyclohexane or toluene can damage the process equipment and that thermal radiation may cause the pressurized hydrogen tanks to rupture. The rupture-type vent system can serve as a critical safety measure for preventing and mitigating the examined scenario.
Hydrogen-enhanced Fatigue Crack Growth in Steels and its Frequency Dependence
Jun 2017
Publication
In the context of the fatigue life design of components particularly those destined for use in hydrogen refuelling stations and fuel cell vehicles it is important to understand the hydrogen-induced fatigue crack growth (FCG) acceleration in steels. As such the mechanisms for acceleration and its influencing factors are reviewed and discussed in this paper with a special focus on the peculiar frequency dependence of the hydrogen-induced FCG acceleration. Further this frequency dependence is debated by introducing some potentially responsible elements along with new experimental data obtained by the authors.
This article is part of the themed issue ‘The challenges of hydrogen and metals’.
Link to document download on Royal Society Website
This article is part of the themed issue ‘The challenges of hydrogen and metals’.
Link to document download on Royal Society Website
Hydrogen Permeation Under High Pressure Conditions and the Destruction of Exposed Polyethylene-property of Polymeric Materials for High-pressure Hydrogen Devices (2)-
Feb 2021
Publication
Aiming to elucidate physical property affecting to hydrogen gas permeability of polymer materials used for liner materials of storage tanks or hoses and sealants under high-pressure environment as model materials with different free volume fraction five types of polyethylene were evaluated using two methods. A convenient non-steady state measurement of thermal desorption analysis (TDA) and steady-state high-pressure hydrogen gas permeation test (HPHP) were used both under up to 90 MPa of practical pressure. The limit of TDA method of evaluation for the specimens suffering fracture during decompression process after hydrogen exposure was found. Permeability coefficient decreased with the decrease of diffusion coefficient under higher pressure condition. Specific volume and degree of crystallinity under hydrostatic environment were measured. The results showed that the shrinkage in free volume caused by hydrostatic effects of the applied hydrogen gas pressure decreases diffusion coefficient resulting in the decrease of permeability coefficient with the pressure rise.
Effects of Hydrogen Pressure, Test Frequency and Test Temperature on Fatigue Crack Growth Properties of Low-carbon Steel in Gaseous Hydrogen
Jul 2016
Publication
Fatigue crack growth (FCG) tests for compact tension (CT) specimens of an annealed low-carbon steel JIS-SM490B were performed under various combinations of hydrogen pressures ranging from 0.1 to 90 MPa test frequencies from 0.001 to 10 Hz and test temperatures of room temperature (RT) 363 K and 423 K. In the hydrogen pressures of 0.1 0.7 and 10 MPa at RT the FCG rate increased with a decrease in the test frequency; then peaked out. In the lower test frequency regime the FCG rate decreased and became nearly equivalent to the FCG rate in air. Also in hydrogen pressure of 45 MPa at RT the hydrogen-assisted FCG acceleration showed an upper limit around the test frequencies of 0.01 to 0.001 Hz. On the other hand in the hydrogen pressure of 90 MPa at RT the FCG rate monotonically increased with a decrease in the test frequency and eventually the upper limit of FCG acceleration was not confirmed down to the test frequency of 0.001 Hz. In the hydrogen pressure of 0.7 MPa at the test frequency of 1 Hz and temperatures of 363 K and 423 K the stress intensity factor range ΔK for the onset of the FCG acceleration in hydrogen gas was shifted to a higher ΔK with an increase in the test temperature. The laser-microscope observation at specimen surface revealed that the hydrogen-assisted FCG acceleration always accompanied a localization of plastic deformation near crack tip. These results infer that the influencing factor dominating the hydrogen-assisted FCG acceleration is not the presence or absence of hydrogen in material but is how hydrogen localizes near the crack tip. Namely a steep gradient of hydrogen concentration can result in the slip localization at crack tip which enhances the Hydrogen Enhanced Successive Fatigue Crack Growth (HESFCG) proposed by the authors. It is proposed that such a peculiar dependence of FCG rate on hydrogen pressure test frequency and test temperature can be unified by using a novel parameter representing the gradient of hydrogen concentration near crack tip.
Safety Concept of Nuclear Cogeneration of Hydrogen and Electricity
Oct 2015
Publication
There is a significant potential for nuclear combined heat and power (CHP) in quite a number of industries. The reactor concepts of the next generation would be capable to open up in particular the high temperature heat market where nuclear energy is applicable to the production processes of hydrogen (or liquid fuels) by steam reforming or water splitting. Due to the need to locate a nuclear facility near the hydrogen plant an overall safety concept has to deal with the question of safety of the combined nuclear/industrial system by taking into account a qualitatively new class of events characterized by interacting influences. Specific requirements will be determined by such factors as the reactor type the nature of the industrial process the separation distances of the industrial facility and population centers from the nuclear plant and prevailing public attitudes. Based on the Japanese concept of the GTHTR300C nuclear reactor for electricity and hydrogen cogeneration theoretical studies were conducted on the release dispersive transport and explosion of a hydrogen cloud in the atmosphere for the sake of assessing the required minimum separation distance to avoid any risk to the nuclear plant's safety systems. In the case of sulfur-iodine water splitting the accidental release of process intermediates including large amounts of sulfur dioxide sulfur trioxide and sulfuric acid need to be investigated as well to estimate the potential risk to nuclear installations like the operators' room and estimate appropriate separation distances against toxic gas propagation. Results of respective simulation studies will be presented.
Leakage-type-based Analysis of Accidents Involving Hydrogen Fueling Stations in Japan and USA
Aug 2016
Publication
To identify the safety issues associated with hydrogen fuelling stations incidents at such stations in Japan and the USA were analyzed considering the regulations in these countries. Leakage due to the damage and fracture of main bodies of apparatuses and pipes in Japan and the USA is mainly caused by design error that is poorly planned fatigue. Considering the present incidents in these countries adequate consideration of the usage environment in the design is very important. Leakage from flanges valves and seals in Japan is mainly caused by screw joints. If welded joints are to be used in hydrogen fuelling stations in Japan strength data for welded parts should be obtained and pipe thicknesses should be reduced. Leakage due to other factors e.g. external impact in Japan and the USA is mainly caused by human error. To realize self-serviced hydrogen fuelling stations safety measures should be developed to prevent human error by fuel cell vehicle users.
Non-steady Characteristics of Dispersion and Ignitability for High-pressurized Hydrogen Jet Discharged From a Pinhole
Sep 2017
Publication
Hydrogen gas concentrations and jet velocities were measured downstream by a high response speed flame ionization detector and PIV (Particle Image Velocimetry) in order to investigate the characteristics of dispersion and ignitability for 40–82 MPa high-pressurized hydrogen jet discharged from a nozzle with 0.2 mm diameter. The light emitted from both OH radical and water vapor species yielded from hydrogen combustion ignited by an electric spark were recorded by two high speed cameras. From the results the empirical formula concerning the relationships for time-averaged concentrations concentration fluctuations and ignition probability were obtained to suggest that they would be independent of hydrogen discharge pressure.
In Situ X-ray Absorption Spectroscopy Study on Water Formation Reaction of Palladium Metal Nanoparticle Catalysts
Oct 2015
Publication
Proper management of hydrogen gas is very important for safety security of nuclear power plants. Hydrogen removal by water formation reaction on a catalyst is one of the candidates for creating hydrogen free system. We observed in situ and time-resolved structure change of palladium metal nanoparticle catalyst during the water formation reaction by using X-ray absorption spectroscopy technique. A poisoning effect by carbon monoxide on catalytic activity was also studied. We have found that the creation of oxidized surface layer on palladium metal nanoparticles plays an important role for the water formation reaction process.
A Panoramic Analysis of Hydrogen Utilization Systems Using an Input-output Table for Next Generation Energy Systems
Apr 2017
Publication
The objective of this study is to analyze a government proposal from a panoramic perspective concerning the economic and environmental effects associated with the construction and operation of hydrogen utilization systems by the year 2030. We focused on a marine transport system for hydrogen produced offshore hydrogen gas turbine power generation fuel cell vehicles (FCVs) and hydrogen stations as well as residential fuel cell systems (RFCs). In this study using an Input-Output Table for Next Generation Energy Systems (IONGES) we evaluated the induced output labor and CO2 emissions from the construction and operation of these hydrogen technologies using a uniform approach. This may be helpful when considering future designs for the Japanese energy system. In terms of per 1 t-H2 of hydrogen use CO2 reductions from the use of FCVs are considerably higher than the additional CO2 emissions from foreign production and transportation of hydrogen. Because new construction of a hydrogen pipeline network is not considered to be realistic RFCs is assumed to consume hydrogen generated by refining town gas. In this case the CO2 reductions from using RFCs will decline under the electricity composition estimated for 2030 on the condition of a substantial expansion of electricity generation from renewable energy sources. However under the present composition of electricity production we can expect a certain amount of CO2 reductions from using RFCs. If hydrogen is directly supplied to RFCs CO2 reductions increase substantially. Thus we can reduce a significant amount of CO2 emissions if various unused energy sources dispersed around local areas or unharnessed renewable energies such as solar and wind power can be converted into hydrogen to be supplied to FCVs and RFCs.
Effect of Supercharging on Improving Thermal Efficiency and Modifying Combustion Characteristics in Lean-burn Direct-injection Near-zero-emission Hydrogen Engines
Oct 2021
Publication
The authors have proposed a new combustion process called the Plume Ignition Combustion Concept (PCC) in which with an optimal combination of hydrogen injection timing and controlled jet geometry the plume of the hydrogen jet is spark-ignited to accomplish combustion of a rich mixture. This combustion process markedly improves thermal efficiency by reducing cooling loss which is essential for increasing thermal efficiency in a hydrogen engine while maintaining high power. In order to improve thermal efficiency and reduce NOx formation further PCC was applied to a lean-burn regime to burn a leaner mixture globally. In this study the effect of supercharging which was applied to recover the reduced output power due to the leaner mixture on improving thermal efficiency was confirmed along with clarifying the cause.
Evaluation of Hydrogen-induced Cracking in High-strength Steel Welded Joints by Acoustic Emission Technique
Feb 2020
Publication
Hydrogen-induced cracking behavior in high-strength steel mainly composed of martensite was analyzed by acoustic emission (AE) technique and finite element method (FEM) in slow strain-rate tensile (SSRT) tests and welding tests. The crack initiation was detected by the AE signals and the time evolution of stress concentration and hydrogen diffusion were calculated by FEM. The effect of hardness and plastic strain on the hydrogen diffusion coefficientwas explicitly introduced into the governing equation in FEM. The criterion and indicator parameter for the crack initiation were derived as a function of maximum principal stress and locally accumulated hydrogen concentration. The results showed that the cracking criterion derived by AE and FEM is useful for predicting the cold cracking behavior and determining the critical preheat temperature to prevent hydrogeninduced cracking.
Measurement of Hydrogen Mixing Process by High Response Hydrogen Sensor
Sep 2017
Publication
According to the Global technical regulation on hydrogen and fuel cell vehicles (FCV) fuel cell discharge system at the vehicle exhaust system`s point of discharge the hydrogen concentration level shall not exceed 4 % average by volume during any moving three-second time interval during normal operation including start-up and shut down [1]. FC stack need to washout by the concentrated hydrogen as the purge gas and how to exhaust gas without exceeding 4 % is the most concerns. Also how to measure hydrogen pulse of millisecond in exhaust is also the rising up issue. In this paper model of FCV hydrogen discharge system was composed and variety of simple experiments were carried out to control the H2 concentration and release. In the case which the semiconductor sensor with porous material (average size less than quench distance) were applied to check H2 concentration the short pulse of high concentration of H2 in millisecond was hard to find. In this experiment the simple exhaust gas model H2/N2 flow was used instead of Air/H2. In the exhaust gas test experiment was conducted under the atmospheric condition in room temperature with small pressure difference and the fast solenoid valve to create quick hydrogen control. Most of the experiments except the turbulent flow experiments laminar flow is expected to be dominated when steady state condition is satisfied but the most result discussed here is the measurement of H2 concentration during the start point at the time of discharge within seconds. The results showed when H2 was added to N2 flow the boundary layer between N2 and H2 contained the high concentration of H2 at the initial wave front and decrease to reach steady state. This H2 pulse is typical in the FCV exhaust gas and topics of this paper.
Attained Temperature During Gas Fuelling and Defueling Cycles of Compressed Hydrogen Tanks for FCV
Sep 2011
Publication
In this study we conducted hydrogen gas filling and discharging cycling tests to examine the thermal behaviour in hydrogen storage tanks under actual use conditions. As a result it was confirmed that the gas temperature in the tank varied depending on the initial test conditions such as the ambient temperature of the tank and the filling gas temperature and that the gas temperature tended to stabilize after several gas filling and discharging cycles.
No more items...