Netherlands

This work discusses the design and demonstration of an in-situ test setup for testing pipeline steels in a high pressure gaseous hydrogen (H2 ) environment. A miniature hollow pipe-like tensile specimen was designed that acts as the gas containment volume during the test. Specific areas of the specimen can be forced to fracture by selective notching as performed on the weldment. The volume of H2 used was minimised so the test can be performed safely without the need of specialised equipment. The setup is shown to be capable of characterising Hydrogen Embrittlement (HE) in steels through testing an X60 pipeline steel and its weldment. The percentage elongation (%El) of the base metal was found to be reduced by 40% when tested in 100 barg H2 . Reduction of cross-sectional area (%RA) was found to decrease by 28% and 11% in the base metal and weld metal respectively when tested in 100 barg H2 . Benchmark test were performed at 100 barg N2 pressure. SEM fractography further indicated a shift from normal ductile fracture mechanisms to a brittle transgranular (TG) quasi-cleavage (QC) type fracture that is characteristic of HE.

Aqueous phase reforming of sorbitol was carried out in a 1.7 m long 320 mm ID microchannel reactor with a 5 mm Pt-based washcoated catalyst layer combined with nitrogen stripping. The performance of this microchannel reactor is correlated to the mass transfer properties reaction kinetics hydrogen selectivity and product distribution. Mass transfer does not affect the rate of sorbitol consumption which is limited by the kinetics of the reforming reaction. Mass transfer significantly affects the hydrogen selectivity and the product distribution. The rapid consumption of hydrogen in side reactions at the catalyst surface is prevented by a fast mass transfer of hydrogen from the catalyst site to the gas phase in the microchannel reactor. This results in a decrease of the concentration of hydrogen at the catalyst surface which was found to enhance the desired reforming reaction rate at the expense of the undesired hydrogen consuming reactions. Compared to a fixed bed reactor the selectivity to hydrogen in the microchannel reactor was increased by a factor of 2. The yield of side products (mainly C3 and heavier hydrodeoxygenated species) was suppressed while the yield of hydrogen was increased from 1.4 to 4 moles per mole of sorbitol fed.

The transition to a more sustainable personal transportation sector requires the widespread adoption of electric vehicles. However a dominant design has not yet emerged and a standards battle is being fought between battery and hydrogen fuel cell powered electric vehicles. The aim of this paper is to analyze which factors are most likely to influence the outcome of this battle thereby reducing the uncertainty in the industry regarding investment decisions in either of these technologies. We examine the relevant factors for standard dominance and apply a multi-criteria decision-making method best worst method to determine the relative importance of these factors. The results indicate that the key factors include technological superiority compatibility and brand reputation and credibility. Our findings show that battery powered electric vehicles have a greater chance of winning the standards battle. This study contributes to theory by providing further empirical evidence that the outcome of standards battles can be explained and predicted by applying factors for standard success. We conclude that technology dominance in the automotive industry is mostly driven by technological characteristics and characteristics of the format supporter.

As of 2003 15 hydrogen refuelling stations (HRSs) have been deployed in the Netherlands. To become established the HRS has to go through a permitting procedure. An important document of the permitting dossier is the quantitative risk assessment (QRA) as it assesses the risks of the HRS associated to people and buildings in the vicinity of the HRS. In the Netherlands a generic prescribed approach exists on how to perform a QRA however specific guidelines for HRSs do not exist. An intercomparison among the QRAs of permitted HRSs has revealed significant inconsistencies on various aspects of the QRA: namely the inclusion of HRS sub-systems and components the HRS sub-system and component considerations as predefined components the application of failure scenarios the determination of failure frequencies the application of input parameters the consideration of preventive and mitigation measures as well as information provided regarding the HRS surroundings and the societal risk. It is therefore recommended to develop specific QRA guidelines for HRSs.

Short refuelling time and high final state of charge are among the main hydrogen car user's requirements. To meet these requirements without exceeding the tank materials safety limits hydrogen precooling is needed. Filling experiments with different inlet gas temperatures and mass flow rates have been executed using two different types of on-board tanks (type 3 and 4). State of charge has a strong dependency on the inlet gas temperature. This dependency is more visible for type 4 tanks. Lowest precooling temperature (−40 °C) is not always required in order to meet user's requirements so energy savings can be achieved if the initial conditions of the tank are correctly identified. The results of the experiments performed have been compared with the SAE J2601 look-up tables for non-communication fillings. A big safety margin has been observed in these tables. Refuelling could be performed faster and with less demanding precooling requirements if the initial conditions and the configuration of the hydrogen storage system are well known.

Simulation of hydrogen-air mixture explosions in a closed large-scale vessel with uniform and nonuniform mixture compositions was performed by the group of partners within the EC funded project “Hydrogen Safety as an Energy Carrier” (HySafe). Several experiments were conducted previously by Whitehouse et al. in a 10.7 m3 vertically oriented (5.7-m high) cylindrical facility with different hydrogen-air mixture compositions. Two particular experiments were selected for simulation and comparison as a Standard Benchmark Exercise (SBEP) problem: combustion of uniform 12.8% (vol.) hydrogen-air mixture and combustion of non-uniform hydrogen-air mixture with average 12.6% (vol.) hydrogen concentration across the vessel (vertical stratification 27% vol. hydrogen at the top of the vessel 2.5% vol. hydrogen at the bottom of the vessel); both mixtures were ignited at the top of the vessel. The paper presents modelling approaches used by the partners comparison of simulation results against the experiment data and conclusions regarding the non-uniform mixture combustion modelling in real-life applications.

The “SUpport to SAfety aNAlysis of Hydrogen and Fuel Cell Technologies (SUSANA)” project aims to support stakeholders using Computational Fluid Dynamics (CFD) for safety engineering design and assessment of FCH systems and infrastructure through the development of a model evaluation protocol. The protocol covers all aspects of safety assessment modelling using CFD from release through dispersion to combustion (self-ignition fires deflagrations detonations and Deflagration to Detonation Transition - DDT) and not only aims to enable users to evaluate models but to inform them of the state of the art and best practices in numerical modelling. The paper gives an overview of the SUSANA project including the main stages of the model evaluation protocol and some results from the on-going benchmarking activities.

Transitioning from fossil fuels to sustainable and green energy sources in mobile applications is a difficult challenge and demands sustained and highly multidisciplinary efforts in R&D. Liquid organic hydrogen carriers (LOHC) offer several advantages over more conventional energy storage solutions but have not been yet demonstrated at scale. Herein we describe the development of an integrated and compact 25 kW formic acid-to-power system by a team of BSc and MSc students. We highlight a number of key engineering challenges encountered during scale-up of the technology and discuss several aspects commonly overlooked by academic researchers. Conclusively we provide a critical outlook and suggest a number of developmental areas currently inhibiting further implementation of the technology.

Tensile and fatigue tests were performed on an AA2198 aluminum alloy in the T851 condition in ambient air and liquid hydrogen (LH2). All fatigue tests were performed under load control at a frequency of 20 Hz and a stress ratio of R=0.1. The Gecks-Och-Function [1] was fitted on the measured cyclic lifetimes.<br/><br/>The tensile strength in LH2 was measured to be 46 % higher compared to the value determined at ambient conditions and the fatigue limit was increased by approximately 60 %. Both S-N curves show a distinct S-shape but also significant differences. Under LH2 environment the transition from LCF- to HCF-region as well as the transition to the fatigue limit is shifted to higher cyclic lifetimes compared to ambient test results. The investigation of the crack surfaces showed distinct differences between ambient and LH2 conditions. These observed differences are important factors in the fatigue behavior change.

One alternative for the storage and transport of hydrogen is blending a low amount of hydrogen (up to 15 or 20%) into existing natural gas grids. When demanded hydrogen can be then separated close to the end users using membranes. In this work composite alumina carbon molecular sieves membranes (Al-CMSM) supported on tubular porous alumina have been prepared and characterized. Single gas permeation studies showed that the H₂/CH₄ separation properties at 30 °C are well above the Robeson limit of polymeric membranes. H₂ permeation studies of the H2–CH4 mixture gases containing 5–20% of H2 show that the H2 purity depends on the H₂ content in the feed and the operating temperature. In the best scenario investigated in this work for samples containing 10% of H₂ with an inlet pressure of 7.5 bar and permeated pressure of 0.01 bar at 30 °C the H₂ purity obtained was 99.4%.

Hydrogen sensors are recognized as an important technology for facilitating the safe implementation of hydrogen as an alternative fuel and there are numerous reports of a sensor alarm successfully preventing a potentially serious event. However gaps in sensor metrological specifications as well as in their performance for some applications exist. The U.S. Department of Energy (DOE) Fuel Cell Technologies Office published a short list of critical gaps in the 2007 and 2012 Multiyear Project Plans; more detailed gap analyses were independently performed by the Joint Research Centre (JRC) and the National Renewable Energy Laboratory (NREL). There have been however some significant advances in sensor technologies since these assessments including the commercial availability of hydrogen sensors with fast response times (t90 < 1 s which had been an elusive DOE target since 2007) improved robustness to chemical poisons improved selectivity and improved lifetime and stability. These improvements however have not been universal and typically pertain to select platforms or models. Moreover as hydrogen markets grow and new applications are being explored more demands will be imposed on sensor performance. The hydrogen sensor laboratories at NREL and the JRC are currently updating the hydrogen safety sensor gap analysis through direct interaction with international stakeholders in the hydrogen community especially end users. NREL and the JRC are currently organizing a series of workshops (in Europe and the United States) with sensor developers end-users and other stakeholders in 2017 to identify technology gaps and to develop a path forward to address them. One workshop was held on May 10 in Brussels Belgium at the Headquarters of the Fuel Cell and Hydrogen Joint Undertaking. A second workshop is planned at NREL in Golden CO USA. This paper reviews improvements in sensor technologies in the past 5 to 10 years identifies gaps in sensor performance and use requirements and identifies potential research strategies to address the gaps. The outcomes of the Hydrogen Sensors Workshops are also summarized.

In the context of the French DIMITRHY project ANR-08-PANH006 experiments have been carried out to measure helium injections in a cubic 1 m3 box - GAMELAN in a reproducible and quantitative manner. For the present work we limit ourselves to the unique configuration of a closed box with a small hole at its base to prevent overpressure. This case leads to enough difficulties of modelisations to deserve our attention. The box is initially filled with air and injections of helium through a tube of diameter 20 mm is operated. The box is instrumented with catharometres to measure the helium volume concentration within an accuracy better than 0.1%. We present the CFD (Fluent and CASTEM ANSYS-CFX and ADREA-HF) calculations results obtained by 5 different teams participating to the benchmark in the following situation: the case of a plume release of helium in a closed box (4NL/min). Parts of the CFD simulations were performed in the European co-funded project HyIndoor others were performed in the French ANR-08-PANH006 DimitrHy project.

Direct internal reforming enables optimal heat integration and reduced complexity in solid oxide fuel cell (SOFC) systems but thermal stresses induced by the increased temperature gradients may inflict damage to the stack. Therefore the development of adequate control strategies requires models that can accurately predict the temperature profiles in the stack. A 1D dynamic modelling platform is developed in this study and used to simulate SOFCs in both single cell and stack configurations. The single cell model is used to validate power law and Hougen-Watson reforming kinetics derived from experiments in previous work. The stack model based on the same type of cells accounts for heat transfer in the inactive area and to the environment and is validated with data reported by the manufacturer. The reforming kinetics are then implemented in the stack model to simulate operation with direct internal reforming. Although there are differences between the temperature profiles predicted by the two kinetic models both are more realistic than assuming chemical equilibrium. The results highlight the need to identify rate limiting steps for the reforming and hydrogen oxidation reactions on anodes of functional SOFC assemblies. The modelling approach can be used to study off-design conditions transient operation and system integration as well as to develop adequate energy management and control strategies.

This paper addresses how a global climate target may influence iron and steel production technology deployment and scrap use. A global energy system model ETSAP-TIAM was used and a Scrap Availability Assessment Model (SAAM) was developed to analyse the relation between steel demand recycling and the availability of scrap and their implications for steel production technology choices. Steel production using recycled materials has a continuous growth and is likely to be a major route for steel production in the long run. However as the global average of in-use steel stock increases up to the current average stock of the industrialised economies global steel demand keeps growing and stagnates only after 2050. Due to high steel demand levels and scarcity of scrap more than 50% of the steel production in 2050 will still have to come from virgin materials. Hydrogen-based steel production could become a major technology option for production from virgin materials particularly in a scenario where Carbon Capture and Storage (CCS) is not available. Imposing a binding climate target will shift the crude steel price to approximately 500 USD per tonne in the year 2050 provided that CCS is available. However the increased prices are induced by CO₂ prices rather than inflated production costs. It is concluded that a global climate target is not likely to influence the use of scrap whereas it shall have an impact on the price of scrap. Finally the results indicate that energy efficiency improvements of current processes will only be sufficient to meet the climate target in combination with CCS. New innovative techniques with lower climate impact will be vital for mitigating climate change.

This paper presents a compilation of the results supplied by HySafe partners participating in the Standard Benchmark Exercise Problem (SBEP) V2 which is based on an experiment on hydrogen combustion that is first described. A list of the results requested from participants is also included. The main characteristics of the models used for the calculations are compared in a very succinct way by using tables. The comparison between results together with the experimental data when available is made through a series of graphs. The results show quite good agreement with the experimental data. The calculations have demonstrated to be sensitive to computational domain size and far field boundary condition.

Today it is not known – neither qualitatively not quantitatively - how large the impact can be of the promoters on sensitivity to hydrogen-air detonation in hypothetical accidents at hydrogen-containing installations transport or storage facilities. Report goal is to estimate theoretically an effect of hydrogen-peroxide (as representative promoter) on sensitivity to detonation of the stoichiometric hydrogen-oxygen gas mixtures. The classical H₂-O2-Ar (2:1:7) gas mixture was chosen as reference system with the well established and unambiguously interpreted experimental data. In kinetic simulations it was found that the ignition delay time is sensitive to H₂O₂addition for small initial H₂O₂concentrations and is nearly constant for the large ones. Parametric reactive CFD studies of two dimensional cellular structure of 2H₂-O₂-7Ar-H₂O₂ detonations with variable hydrogen peroxide concentration (up to 10 vol.%) were also performed. Two un-expected results were obtained. First result: detonation cell size is practically independent upon variation of initial hydrogen peroxide concentration. For practical applications it means that presence of hydrogen-peroxide did not change drastically sensitivity of the stoichiometric hydrogen-oxygen gas mixtures. These theoretical speculations require an experimental verification. Second result: for large enough initial H₂O₂concentrations (> 1 vol.% at least) a new element of cellular structure of steady detonation wave was revealed. It is a system of multiple secondary longitudinal shock waves (SLSW) which propagates in the direction opposite to that of the leading shock wave. Detailed mechanism of SLSW formation is proposed.

Extensive infrastructure exists for the transport of natural gas and it is an obvious step to assess its use for the movement of hydrogen. The Naturalhy project’s objective is to prepare the European natural gas industry for the introduction of hydrogen by assessing the capability of the natural gas infrastructure to accept mixtures of hydrogen and natural gas. This paper presents the ongoing work within both Durability and Integrity Work Packages of the Naturalhy project. This work covers a gap in knowledge on risk assessment required for delivering H2+natural gas blends by means of the existing natural gas grids in safe operation.<br/>Experiments involving several parts of the existing infrastructure will be described that are being carried out to re-examine the major risks previously studied for natural gas including: effect of H2 on failure behaviour and corrosion of transmission pipes and their burst resistance (link to the Work Package Safety) on permeability and ageing of distribution pipes on reliability and ageing of domestic gas meters tightness to H2 of domestic appliances and their connexions. The information will be integrated into existing Durability assessment methodologies originally developed for natural gas.<br/>An Integrity Management Tool will be developed taking account of the effect of hydrogen on the materials properties. The tool should enable a cost effective selection of appropriate measures to control the structural integrity and maintaining equipment. The main measures considered are monitoring non destructive examination (pigging and non pigging) and repair strategies. The tool will cover a number of parameters e.g.: percentage of hydrogen in the gas mixture material of construction operating conditions and condition of cathodic protection. Thus the Integrity Management Tool will yield an inspection and maintenance plan based on the specific circumstances.

The production of hydrogen through water splitting in a photoelectrochemical cell suffers from an overpotential that limits the efficiencies. In addition hydrogen-peroxide formation is identified as a competing process affecting the oxidative stability of photoelectrodes. We impose spin-selectivity by coating the anode with chiral organic semiconductors from helically aggregated dyes as sensitizers; Zn-porphyrins and triarylamines. Hydrogen peroxide formation is dramatically suppressed while the overall current through the cell correlating with the water splitting process is enhanced. Evidence for a strong spin-selection in the chiral semiconductors is presented by magnetic conducting (mc-)AFM measurements in which chiral and achiral Zn-porphyrins are compared. These findings contribute to our understanding of the underlying mechanism of spin selectivity in multiple electron-transfer reactions and pave the way toward better chiral dye-sensitized photoelectrochemical cells.

Considering the transition towards the hydrogen economy dependent on hydrogen penetration scenario the cost of a new hydrogen pipeline infrastructure in Europe may amount to several thousands of billions of EURO’s. Therefore the examination of the potential contribution of the existing natural gas assets is a practical and logical first step. As the physical and chemical properties of hydrogen differ significantly from those of natural gas it is not at all possible to simply exchange natural gas by hydrogen in the existing infrastructure. In this paper first a brief overview will be given of the NATURALHY-project. Further the focus will be on the impact of added hydrogen on the performance of existing natural gas domestic end user appliances which is related to the operation of the natural gas grid connecting the different types of appliance. The application of the fundamental insights and carefully designed experiments comparing the behaviour of gases using justified reference conditions have been shown to offer essential progress. The Wobbe index limits of the natural gas distributed pose a first limiting factor upon the maximum allowable hydrogen concentration. Constant-Wobbe index and decreasing-Wobbe index options of H2 admixture have been studied. Considering the appliance light back H2 limiting factor for domestic appliances fuel-rich appliances are the critical ones. Also taking into account stationary gas engines gas turbines industrial applications and natural gas grid management it is not yet justified to present statements on what level of hydrogen concentration could be safely allowed in which specific natural gas distribution region. But more clarity has been obtained on combustion safety aspects of existing domestic appliances on the connection with Wobbe distribution conditions and on the bottlenecks still to be handled.

Citizens’ emotional responses to energy technology projects influence the success of the technology’s implementation. Contrary to popular belief these emotions can have a systematic base. Bringing together insights from appraisal theory and from technology acceptance studies this study develops and tests hypotheses regarding antecedents of anger fear joy and pride about a local hydrogen fuel station (HFS). A questionnaire study was conducted among 271 citizens living near the first publicly accessible HFS in the Netherlands around the time of its implementation. The results show that anger is significantly explained by (from stronger to weaker effects) perceived procedural and distributive unfairness and fear by distributive unfairness perceived safety procedural unfairness gender and prior awareness. Joy is significantly explained by perceived environmental outcomes and perceived usefulness and pride by prior awareness perceived risks trust in industry and perceived usefulness. The study concludes that these predictors are understandable practical and moral considerations which can and should be taken into account when developing and executing a project.

Liquid hydrogen (LH2) storage is viewed as a viable approach to assure sufficient hydrogen capacity at commercial fuelling stations. Presently LH2 is produced at remote facilities and then transported to the end-use site by road vehicles (i.e. LH2 tanker trucks). Venting of hydrogen to depressurize the transport storage tank is a routine part of the LH2 delivery and site transfer process. The behaviour of cold hydrogen plumes has not been well characterized because of the sparsity of empirical field data which can lead to overly conservative safety requirements. Committee members of the National Fire Protection Association (NFPA) Standard 2 [1] formed the Hydrogen Storage Safety Task Group which consists of hydrogen producers safety experts and computational fluid dynamics modellers has identified the lack of understanding of hydrogen dispersion during LH2 venting of storage vessels as a critical gap for establishing safety distances at LH2 facilities especially commercial hydrogen fuelling stations. To address this need the National Renewable Energy Laboratory Sensor Laboratory in collaboration with the NFPA Hydrogen Storage Task Group developed a prototype Cold Hydrogen Plume Analyzer to empirically characterize the hydrogen plume formed during LH2 storage tank venting. The prototype analyzer was field deployed during an actual LH2 venting process. Critical findings included

• Hydrogen above the lower flammable limit (LFL) was detected as much as 2 m lower than the release point which is not predicted by existing models.
• Personal monitors detected hydrogen at ground level although at levels below the LFL.
• A small but inconsistent correlation was found between oxygen depletion and the hydrogen concentration.
• A negligible to non-existent correlation was found between in-situ temperature measurements and the hydrogen concentration.

The prototype analyzer is being upgraded for enhanced metrological capabilities including improved real-time spatial and temporal profiling of hydrogen plumes and tracking of prevailing weather conditions. Additional deployments are planned to monitor plume behaviour under different wind humidity and temperature conditions. The data will be shared with the Hydrogen Storage Task Group and ultimately will be used support theoretical models and code requirements prescribed in NFPA 2.

Contrary to several reports in the recent literature the use of oxygen sensors for indirectly monitoring ambient hydrogen concentration has serious drawbacks. This method is based on the assumption that a hydrogen release will displace oxygen which is quantified using oxygen sensors. Despite its shortcomings the draft Hydrogen Vehicle Global Technical Regulation lists this method as a means to monitor hydrogen leaks to verify vehicle fuel system integrity. Experimental evaluations that were designed to impartially compare the ability of commercial oxygen and hydrogen sensors to reliably measure and report hydrogen concentration changes are presented. Numerous drawbacks are identified and discussed.

Interest in hydrogen as a carbon-neutral energy carrier is on the rise around the globe including in Europe. In particular power-to-gas as a technology to transform electricity to hydrogen is receiving ample attention. This article scrutinises current updates in the energy law framework of the EU to explain the legal pre-conditions for the various possible applications of power-to-gas technology. It highlights the influence of both electricity and gas legislation on conversion storage and transmission of hydrogen and demonstrates why ‘green’ hydrogen might come with certain legal privileges under the Renewable Energy Directive attached to it as opposed to the European Commission’s so-called ‘clean’ hydrogen. The article concludes by advocating for legal system integration in EU energy law namely merging the currently distinct EU electricity and gas law frameworks into one unified EU Energy Act.

Hydrogen energy applications often require that systems are used indoors (e.g. industrial trucks for materials handling in a warehouse facility fuel cells located in a room or hydrogen stored and distributed from a gas cabinet). It may also be necessary or desirable to locate some hydrogen system components/equipment inside indoor or outdoor enclosures for security or safety reasons to isolate them from the end-user and the public or from weather conditions.<br/>Using of hydrogen in confined environments requires detailed assessments of hazards and associated risks including potential risk prevention and mitigation features. The release of hydrogen can potentially lead to the accumulation of hydrogen and the formation of a flammable hydrogen-air mixture or can result in jet-fires. Within Hyindoor European Project carried out for the EU Fuel Cells and Hydrogen Joint Undertaking safety design guidelines and engineering tools have been developed to prevent and mitigate hazardous consequences of hydrogen release in confined environments. Three main areas are considered: Hydrogen release conditions and accumulation vented deflagrations jet fires and including under-ventilated flame regimes (e.g. extinguishment or oscillating flames and steady burns). Potential RCS recommendations are also identified.

Hydrogen fuelled vehicles can play a key role in the decarbonisation of transport and reducing emissions. To ensure the durability of fuel cells a specification has been developed (ISO 14687) setting upper limits to the amount fraction of a series of impurities. Demonstrating conformity with this standard requires demonstrating by measurement that the actual levels of the impurities are below the thresholds. Currently the industry is unable to do so for measurement standards and sensitive dedicated analytical methods are lacking. In this work we report on the development of such measurement standards and methods for four reactive components: formaldehyde formic acid hydrogen chloride and hydrogen fluoride. The primary measurement standard is based on permeation and the analytical methods on highly sensitive and selective laser-based spectroscopic techniques. Relative expanded uncertainties at the ISO 14687 threshold level in hydrogen of 4% (formaldehyde) 8% (formic acid) 5% (hydrogen chloride) and 8% (hydrogen fluoride) have been achieved.

Gas sensors are applied for facilitating the safe use of hydrogen in for example fuel cell and hydrogen fuelled vehicles. New sensor developments aimed at meeting the increasingly stringent performance requirements in emerging applications are presented based on in-house technical developments and a literature study. The strategy of combining different detection principles i.e. sensors based on electrochemical cells semiconductors or field effects in combination with thermal conductivity sensor or catalytic combustion elements in one new measuring system is reported. This extends the dynamic measuring range of the sensor while improving sensor reliability to achieve higher safety integrity through diverse redundancy. The application of new nanoscaled materials nano wires carbon tubes and graphene as well as the improvements in electronic components of field-effect resistive-type and optical systems are evaluated in view of key operating parameters such as sensor response time low energy consumption and low working temperature.

This work presents the results of the Standard Benchmark Exercise Problem (SBEP) V20 of Work Package 6 (WP6) of HySafe Network of Excellence (NoE) co-funded by the European Commission in the frame of evaluating the quality and suitability of codes models and user practices by comparative assessments of code results. The benchmark problem SBEP-V20 covers release scenarios that were experimentally investigated in the past using helium as a substitute to hydrogen. The aim of the experimental investigations was to determine the ventilation requirements for parking hydrogen fuelled vehicles in residential garages. Helium was released under the vehicle for 2 h with 7.200 l/h flow rate. The leak rate corresponded to a 20% drop of the peak power of a 50 kW fuel cell vehicle. Three double vent garage door geometries are considered in this numerical investigation. In each case the vents are located at the top and bottom of the garage door. The vents vary only in height. In the first case the height of the vents is 0.063 m in the second 0.241 m and in the third 0.495 m. Four HySafe partners participated in this benchmark. The following CFD packages with the respective models were applied to simulate the experiments: ADREA-HF using k–ɛ model by partner NCSRD FLACS using k–ɛ model by partner DNV FLUENT using k–ɛ model by partner UPM and CFX using laminar and the low-Re number SST model by partner JRC. This study compares the results predicted by the partners to the experimental measurements at four sensor locations inside the garage with an attempt to assess and validate the performance of the different numerical approaches.

Guidance on Sensor Placement was identified as the top research priority for hydrogen sensors at the 2018 HySafe Research Priority Workshop on hydrogen safety in the category Mitigation Sensors Hazard Prevention and Risk Reduction. This paper discusses the initial steps (Phase 1) to develop such guidance for mechanically ventilated enclosures. This work was initiated as an international collaborative effort to respond to emerging market needs related to the design and deployment equipment for hydrogen infrastructure that is often installed in individual equipment cabinets or ventilated enclosures. The ultimate objective of this effort is to develop guidance for an optimal sensor placement such that when integrated into a facility design and operation will allow earlier detection at lower levels of incipient leaks leading to significant hazard reduction. Reliable and consistent early warning of hydrogen leaks will allow for the risk mitigation by reducing or even eliminating the probability of escalation of small leaks into large and uncontrolled events. To address this issue a study of a real-world mechanically ventilated enclosure containing GH2 equipment was conducted where CFD modelling of the hydrogen dispersion (performed by AVT and UQTR and independently by the JRC) was validated by the NREL Sensor laboratory using a Hydrogen Wide Area Monitor (HyWAM) consisting of a 10-point gas and temperature measurement analyzer. In the release test helium was used as a hydrogen surrogate. Expansion of indoor releases to other larger facilities (including parking structures vehicle maintenance facilities and potentially tunnels) and incorporation into QRA tools such as HyRAM is planned for Phase 2. It is anticipated that results of this work will be used to inform national and international standards such as NFPA 2 Hydrogen Technologies Code Canadian Hydrogen Installation Code (CHIC) and relevant ISO/TC 197 and CEN documents.

The three years European MATHRYCE project dedicated to material testing and design recommendations for components exposed to hydrogen enhanced fatigue started in October 2012. Its main goal is to provide an “easy” to implement methodology based on lab-scale experimental tests under hydrogen gas to assess the service life of a real scale component taking into account fatigue loading under hydrogen gas. Dedicated experimental tests will be developed for this purpose. In the present paper the proposed approach is presented and compared to the methodologies currently developed elsewhere in the world.

This paper introduces a risk-based methodology for hydrogen refuelling stations. Momentarily four stations are present in the Netherlands. This number is expected to increase to around twenty in the next years. For these stations a quantitative risk analysis (QRA) must be carried out to account for spatial planning. The presented method identifies the loss of containment scenarios and failure frequencies. Additionally the results of this study may be used in legislative context in the form of fixed generic safety distances. Using the risk analysis tool Safeti-NL safety distances are determined for three different kinds of hydrogen refuelling stations distinguished by the supply method of the hydrogen. For the hydrogen refuelling stations a maximum safety distance of 35 m is calculated. However despite the relatively small safety distances the maximum effect distances (distance to 1% lethality) can be very large especially for stations with a supply and storage of liquid hydrogen. The research was overseen by an advisory committee which also provided technical information on the refuelling stations.

Hydrogen technologies are expected to play a key role in implementing the transition from a fossil fuel- based to a more sustainable lower-carbon energy system. To facilitate their widespread deployment the safe operation and hydrogen systems needs to be ensured together with the evaluation of the associated risk.<br/>HIAD has been designed to be a collaborative and communicative web-based information platform holding high quality information of accidents and incidents related to hydrogen technologies. The main goal of HIAD was to become not only a standard industrial accident database but also an open communication platform suitable for safety lessons learned and risk communication as well as a potential data source for risk assessment; it has been set up to improve the understanding of hydrogen unintended events to identify measures and strategies to avoid incidents/accidents and to reduce the consequence if an accident occurs.<br/>In order to achieve that goal the data collection is characterized by a significant degree of detail and information about recorded events (e.g. causes physical consequences lesson learned). Data are related not only to real incident and accidents but also to hazardous situations.<br/>The concept of a hydrogen accident database was generated in the frame of the project HySafe an EC co-funded NoE of the 6th Frame Work Programme. HIAD was built by EC-JRC and populated by many HySafe partners. After the end of the project the database has been maintained and populated by JRC with publicly available events. The original idea was to provide a tool also for quantitative risk assessment able to conduct simple analyses of the events; unfortunately that goal could not be reached because of a lack of required statistics: it was not possible to establish a link with potential event providers coming from private sector not willing to share information considered confidential. Starting from June 2016 JRC has been developing a new version of the database (i.e. HIAD 2.0); the structure of the database and the web-interface have been redefined and simplified resulting in a streamlined user interface compared to the previous version of HIAD. The new version is mainly focused to facilitate the sharing of lessons learned and other relevant information related to hydrogen technology; the database will be public and the events will be anonymized. The database will contribute to improve the safety awareness fostering the users to benefit from the experiences of others as well as to share information from their own experiences.

The development of reliable hydrogen sensors is crucial for the safe use of hydrogen. One of the main concerns of end-users is sensor reliability in the presence of species other than the target gas which can lead to false alarms or undetected harmful situations. In order to assess the selectivity of commercial of the shelf (COTS) hydrogen sensors a number of sensors of different technology types were exposed to various interferent gas species. Cross-sensitivity tests were performed in accordance to the recommendations of ISO 26142:2010 using the hydrogen sensor testing facilities of NREL and JRC-IET. The results and conclusions arising from this study are presented.

Progressing limits on pollutant emissions oblige ship owners to reduce the environmental impact of their operations. Fuel cells may provide a suitable solution since they are fuel efficient while they emit few hazardous compounds. Various choices can be made with regard to the type of fuel cell system and logistic fuel and it is unclear which have the best prospects for maritime application. An overview of fuel cell types and fuel processing equipment is presented and maritime fuel cell application is reviewed with regard to efficiency gravimetric and volumetric density dynamic behaviour environmental impact safety and economics. It is shown that low temperature fuel cells using liquefied hydrogen provide a compact solution for ships with a refuelling interval up to a tens of hours but may result in total system sizes up to five times larger than high temperature fuel cells and more energy dense fuels for vessels with longer mission requirements. The expanding infrastructure of liquefied natural gas and development state of natural gas-fuelled fuel cell systems can facilitate the introduction of gaseous fuels and fuel cells on ships. Fuel cell combined cycles hybridisation with auxiliary electricity storage systems and redundancy improvements are identified as topics for further study

Delft University of Technology under its ‘‘Green Village” programme has an initiative to build a power plant (car parking lot) based on the fuel cells used in vehicles for motive power. It is a trigeneration system capable of producing electricity heat and hydrogen. It comprises three main zones: a hydrogen production zone a parking zone and a pump station zone. This study focuses mainly on the hydrogen production zone which assesses four different system designs in two different operation modes of the facility: Car as Power Plant (CaPP) mode corresponding to the open period of the facility which uses fuel cell electric vehicles (FCEVs) as energy and water producers while parked; and Pump mode corresponding to the closed period which compresses the hydrogen and pumps to the vehicle’s fuel tank. These system designs differ by the reforming technology: the existing catalytic reformer (CR) and a solid oxide fuel cell operating as reformer (SOFCR); and the option of integrating a carbon capture and storage (CCS). Results reveal that the SOFCR unit significantly reduces the exergy destruction resulting in an improvement of efficiency over 20% in SOFCR-based system designs compared to CR-based system designs in both operation modes. It also mitigates the reduction in system efficiency by integration of a CCS unit achieving a value of 2% whereas in CR-based systems is 7–8%. The SOFCR-based system running in Pump mode achieves a trigeneration efficiency of 60%.

The Hydrogen Incident and Accident Database (HIAD) is being developed as a repository of systematic data describing in detail hydrogen-related undesired events (incidents or accidents). It is an open web-based information system serving various purposes such as a data source for lessons learnt risk communication and partly risk assessment. The paper describes the features of the three HIAD modules – the Data Entry Module (DEM) the Data Retrieval Module (DRM) and the Data Analysis Module (DAM) – and the potential impact the database may have on hydrogen safety. The importance of data quality assurance process is also addressed.

From a permeability and selectivity perspective supported thin-film Pd–Ag membranes are the best candidates for high-purity hydrogen recovery for methane-hydrogen mixtures from the natural gas grid. However the high hydrogen flux also results in induced bulk-to-membrane mass transfer limitations (concentration polarization) especially when working at low hydrogen concentration and high pressure which further reduces the hydrogen permeance in the presence of mixtures. Additionally Pd is a precious metal and its price is lately increasing dramatically. The use of inexpensive CMSM could become a promising alternative. In this manuscript a detailed comparison between these two membrane technologies operating under the same working pressure and mixtures is presented.<br/>First the permeation properties of CMSM and Pd–Ag membranes are compared in terms of permeance and purity and subsequently making use of this experimental investigation an economic evaluation including capital and variable costs has been performed for a separation system to recover 25 kg/day of hydrogen from a methane-hydrogen mixture. To widen the perspective also a sensitivity analysis by changing the pressure difference membrane lifetime membrane support cost and cost of Pd/Ag membrane recovery has been considered. The results show that at high pressure the use of CMSM is to more economic than the Pd-based membranes at the same recovery and similar purity.

Future national electricity heating cooling and transport systems need to reach zero emissions. Significant numbers of back-up power plants as well as large-scale energy storage capacity are required to guarantee the reliability of energy supply in 100 percent renewable energy systems. Electricity can be partially converted into hydrogen which can be transported via pipelines stored in large quantities in underground salt caverns to overcome seasonal effects and used as electricity storage or as a clean fuel for transport. The question addressed in this paper is how parked and grid-connected hydrogen-fuelled Fuel Cell Electric Vehicles might balance 100 per cent renewable electricity heating cooling and transport systems at the national level in Denmark Germany Great Britain France and Spain? Five national electricity heating cooling and transport systems are modeled for the year 2050 for the five countries assuming only 50 percent of the passenger cars to be grid-connected Fuel Cell Electric Vehicles the remaining Battery Electric Vehicles. The grid-connected Fuel Cell Electric Vehicle fleet can always balance the energy systems and their usage is low having load factors of 2.1–5.5 percent corresponding to an average use of 190–480 h per car per year. At peak times occurring only a few hours per year 26 to 43 percent of the grid-connected Fuel Cell Electric Vehicle are required and in particular for energy systems with high shares of solar energy such as Spain balancing by grid-connected Fuel Cell Electric Vehicles is mainly required during the night which matches favorably with driving usage.

A combined density functional theory and molecular dynamics approach is employed to study modifications of graphene at atomistic level for better H2 storage. The study reveals H₂ desorption from hydrogenated defective graphene structure V₂₂₂ to be exothermic. H₂ adsorption and desorption processes are found to be more reversible for V₂₂₂ as compared to pristine graphene. Our study shows that V₂₂₂ undergoes brittle fracture under tensile loading similar to the case of pristine graphene. The tensile strength of V₂₂₂ shows slight reduction with respect to their pristine counterpart which is attributed to the transition of sp2 to sp3-like hybridization. The study also shows that the V₂₂₂ structure is mechanically more stable than the defective graphene structure without chemically adsorbed hydrogen atoms. The current fundamental study thus reveals the efficient recovery mechanism of adsorbed hydrogen from V₂₂₂ and paves the way for the engineering of structural defects in graphene for H₂ storage.

The thermal behaviour of several commercial hydrogen tanks has been studied during high pressure (70-84 MPa) hydrogen cycling. The temperature of the gas at different points inside the tank the temperature at the bosses and the tank outer wall temperature have been measured under different filling and emptying conditions. From the experimental results the effect of the filling rate (1.5-4 g/s) and the influence of the liner material in the thermal behaviour of the hydrogen tanks have been evaluated. Bosses thermal response under the different cycling conditions has also been investigated.

Optimal design and operation of multi-energy systems involving seasonal energy storage are often hindered by the complexity of the optimization problem. Indeed the description of seasonal cycles requires a year-long time horizon while the system operation calls for hourly resolution; this turns into a large number of decision variables including binary variables when large systems are analyzed. This work presents novel mixed integer linear program methodologies that allow considering a year time horizon with hour resolution while significantly reducing the complexity of the optimization problem. First the validity of the proposed techniques is tested by considering a simple system that can be solved in a reasonable computational time without resorting to design days. Findings show that the results of the proposed approaches are in good agreement with the full-scale optimization thus allowing to correctly size the energy storage and to operate the system with a long-term policy while significantly simplifying the optimization problem. Furthermore the developed methodology is adopted to design a multi-energy system based on a neighborhood in Zurich Switzerland which is optimized in terms of total annual costs and carbon dioxide emissions. Finally the system behavior is revealed by performing a sensitivity analysis on different features of the energy system and by looking at the topology of the energy hub along the Pareto sets.

The aim of the study is to identify and quantify the additional risks related to hydrogen explosions during the operation of a hydrogen-driven car. In a first attempt the accidents or failures of a simple one-tank hydrogen storage system have been studied as a main source of risk. Three types of initiators are taken into account: crash accidents fire accidents without crash (no other cars are involved) and hydrogen leakages in normal situation with following ignition. The consequences of hydrogen ignition and/or explosion depend strongly on environmental conditions (geometry wind etc.) therefore the different configurations of operational and environmental conditions are specified.<br/>Then Event Tree/Fault Tree methods are applied for the risk assessment.<br/>The results of quantification permit to draw conclusions about the overall added risk of hydrogen technology as well as about the main contributors to the risk. Results of this work will eventually contribute to the on-going pre-normative research in the field of hydrogen safety.

High pressure storage of hydrogen in tanks is a promising option to provide the necessary fuel for transportation purposes. The fill process of a high-pressure tank should be reasonably short but must be designed to avoid too high temperatures in the tank. The shorter the fill should be the higher the maximum temperature in the tank climbs. For safety reasons an upper temperature limit is included in the requirements for refillable hydrogen tanks (ISO 15869) which sets the limit for any fill optimization. It is crucial to understand the phenomena during a tank fill to stay within the safety margins.<br/>The paper describes the fast filling process of hydrogen tanks by simulations based on the Computational Fluid Dynamics (CFD) code CFX. The major result of the simulations is the local temperature distribution in the tank depending on the materials of liner and outer thermal insulation. Different material combinations (type III and IV) are investigated.<br/>Some measurements from literature are available and are used to validate the approach followed in CFX to simulate the fast filling of tanks. Validation has to be continued in future to further improve the predictability of the calculations for arbitrary geometries and material combinations.

The project “Towards a Hydrogen Refuelling Infrastructure for Vehicles” (THRIVE) aimed at the determination of conditions to stimulate the building of a sustainable infrastructure for hydrogen as a car fuel in The Netherlands. Economic scenarios were constructed for the development of such an infrastructure for the next one to four decades. The eventual horizon will require the erection of a few hundred to more than a thousand hydrogen refuelling stations (HRS) in The Netherlands. The risk acceptability policy in The Netherlands implemented in the External Safety Establishments decree requires the assessment and management of safety risks imposed on the public by car fuelling stations. In the past a risk-informed policy has been developed for the large scale introduction of liquefied petroleum gas (LPG) as a car fuel and a similar policy will also be required if hydrogen is introduced in the public domain. A risk assessment methodology dedicated to cope with accident scenarios relevant for hydrogen applications is to be developed. Within the THRIVE project a demo risk assessment was conducted for the possible implementation of an HRS within an existing station for conventional fuels. The studied station is located in an urban area occupied with housing and commercial activities. The HRS is based on delivery and on-site storage of liquid hydrogen and dispensing of high pressure gaseous hydrogen into vehicles. The main challenges in the risk assessment were in the modelling of release and dispersion of liquid hydrogen. Definition of initial conditions for computational fluid dynamics (CFD) modelling to evaluate dispersion of a cold hydrogen air mixture appears rather complex and is not always fully understood. The modelling assumptions in the initial conditions determine to a large extent the likelihood and severity of potential explosion effects. The paper shows the results of the investigation and the sensitivity to the basic assumptions in the model input.

Palladium-based membranes for hydrogen separation have been studied by several research groups during the last 40 years. Much effort has been dedicated to improving the hydrogen flux of these membranes employing different alloys supports deposition/production techniques etc. High flux and cheap membranes yet stable at different operating conditions are required for their exploitation at industrial scale. The integration of membranes in multifunctional reactors (membrane reactors) poses additional demands on the membranes as interactions at different levels between the catalyst and the membrane surface can occur. Particularly when employing the membranes in fluidized bed reactors the selective layer should be resistant to or protected against erosion. In this review we will also describe a novel kind of membranes the pore-filled type membranes prepared by Pacheco Tanaka and coworkers that represent a possible solution to integrate thin selective membranes into membrane reactors while protecting the selective layer. This work is focused on recent advances on metallic supports materials used as an intermetallic diffusion layer when metallic supports are used and the most recent advances on Pd-based composite membranes. Particular attention is paid to improvements on sulfur resistance of Pd based membranes resistance to hydrogen embrittlement and stability at high temperature.

The European Union aims to fully decarbonise the EU economy which requires a complete overhaul of the energy system and its infrastructure by 2050. The European Commission announced the European Green Deal in December 2019 which includes a wide variety of plans to step up climate mitigation policies. Raising the ambitions of EU climate policy will require significant investment in energy efficiency renewable energy new low carbon technologies and grid infrastructure. It will also necessitate the close integration of the electricity and gas sectors and their respective infrastructures. A decarbonised Europe will be based on an interplay between the production of renewable electricity and the conversion of green electrons into green molecules to transport store and supply all sectors with renewable energy at the lowest possible costs. Becau e the necessary investments are made for a period of 20–60 years it is important to understand what types of investments are needed at what scale and by when. This study seeks to shed light on the future design of a fully integrated energy system and formulates recommendations for the emerging EU Green Deal. These recommendations could help accelerate business cases and promote a stable framework to unlock the large investments required to fully decarbonise the EU economy at the lowest societal costs. This study explores EU decarbonisation pathways for gas and gas infrastructure between 2020 and 2050. Large investments and difficult decisions are required to fully decarbonise the energy system at the lowest societal costs yet there is ample opportunity to create new employment and to make Europe the global leader in low carbon technologies. The present study is an update to the 2019 study for the Gas for Climate consortium done by Navigant now called Guidehouse.6 That study called Gas for Climate. The optimal role for gas in a net-zero emissions energy system explored the role and value for renewable and low carbon gases in a net-zero EU energy system in 2050. It analysed the potential of biomethane and hydrogen produced in the EU and the energy system cost benefits of using them through existing gas infrastructure to achieve a net-zero emissions EU energy system. The study found that there is a large opportunity to scale-up renewable gas production in the EU and concluded that full  decarbonisation with a role for renewable gas offers significant societal cost benefits. The energy system costs of an Optimised Gas scenario were compared to those of a Minimal Gas scenario. The Optimal Gas scenario offered over €200 billion in cost savings per year by 2050.  

You can download the whole report by clicking this link

Two electrolysis technologies fed with renewable energy sources are promising for the production of CO₂-free hydrogen and enabling the transition to a hydrogen society: Alkaline Electrolyte (AE) and Polymer Electrolyte Membrane (PEM). However limited information exists on the potential environmental impacts of these promising sustainable innovations when operating on a large-scale. To fill this gap the performance of AE and PEM systems is compared using ex-ante Life Cycle Assessment (LCA) technology analysis and exploratory scenarios for which a refined methodology has been developed to study the effects of implementing large-scale sustainable hydrogen production systems. Ex-ante LCA allows modelling the environmental impacts of hydrogen production exploratory scenario analysis allows modelling possible upscaling effects at potential future states of hydrogen production and use in vehicles in the Netherlands in 2050. A bridging tool for mapping the technological field has been created enabling the combination of quantitative LCAs with qualitative scenarios. This tool also enables diversity for exploring multiple sets of visions. The main results from the paper show with an exception for the “ozone depletion” impact category (1) that large-scale AE and PEM systems have similar environmental impacts with variations lower than 7% in all impact categories (2) that the contribution of the electrolyser is limited to 10% of all impact categories results and (3) that the origin of the electricity is the largest contributor to the environmental impact contributing to more than 90% in all impact categories even when renewable energy sources are used. It is concluded that the methodology was applied successfully and provides a solid basis for an ex-ante assessment framework that can be applied to emerging technological systems.

The first applications of hydrogen in a natural gas grid will be the admixing of low concentrations in an existing distribution grid. For easy quality and process control it is essential to monitor the hydrogen concentration in real time preferably using cost effective monitoring solutions. In this paper we introduce the use of a platinum based hydrogen sensor that can accurately (at 0.1 vol%) and reversibly monitor the concentration of hydrogen in a carrier gas. This carrier gas that can be nitrogen methane or natural gas has no influence on the accuracy of the hydrogen detection. The hydrogen sensor consists of an interdigitated electrode on a chip coated with a platinum nanocomposite layer that interacts with the gas. This chip can be easily added to a gas sensor for natural gas and biogas that was already developed in previous research. Just by the addition of an extra chip we extended the applicability of the natural gas sensor to hydrogen admixing. The feasibility of the sensor was demonstrated in our own (TNO) laboratory and at a field test location of the HyDeploy program at Keele University in the U.K

With the advent of large-scale application of hydrogen transportation becomes crucial. Reusing the existing natural gas transmission system could serve as catalyst for the future hydrogen economy. However a risk analysis of hydrogen transmission in existing pipelines is essential for the deployment of the new energy carrier. This paper focuses on the individual risk (IR) associated with a hazardous hydrogen jet fire and compares it with the natural gas case. The risk analysis adopts a detailed flame model and state of the art computational software to provide an enhanced physical description of flame characteristics.<br/>This analysis concludes that hydrogen jet fires yield lower lethality levels that decrease faster with distance than natural gas jet fires. Consequently for large pipelines hydrogen transmission is accompanied by significant lower IR. Howbeit ignition effects increasingly dominate the IR for decreasing pipeline diameters and cause hydrogen transmission to yield increased IR in the vicinity of the pipeline when compared to natural gas.

Mg attracts much research interest as anode material for Ni-MH batteries thanks to its lightweight cost-effectiveness and high theoretical capacity (2200 mA h g⁻¹). However its practical application is tremendously challenged by the poor hydrogen sorption kinetics passivation from aggressive aqueous electrolytes and insulating nature of MgH₂. Mg-based alloys exhibit enhanced hydrogen sorption kinetics and electrical conductivity but significant amount of costly transition metal elements are required. In this work we have for the first time utilized non-alloyed but catalyzed Mg as anode for Ni-MH batteries. 5 mol.% TiF3 was added to nanosized Mg for accelerating the hydrogen sorption kinetics. Several strategies for preventing the problematic passivation of Mg have been studied including protective encapsulation of the electrode and utilizing room-temperature/high-temperature ionic liquids and an alkaline polymer membrane as working electrolyte. Promising electrochemical performance has been achieved in this Mg–TiF₃ composite anode based Ni-MH batteries with room for further improvements.

The current focus on the massive CO₂ reduction highlights the need for the rapid development of technology for the production storage transportation and distribution of renewable energy. In addition to electricity we need other forms of energy carriers that are more suitable for energy storage and transportation. Hydrogen is one of the main candidates for this purpose since it can be produced from solar or wind energy and then stored; once needed it can be converted back to electricity using fuel cells. Another important aspect of future energy systems is sector coupling where different sectors e.g. mobility and energy work together to provide better services. In such an integrated system electric vehicles – both battery and hydrogen-based fuel cell – can provide when parked electricity services such as backup power and balancing; when driving they produce no emissions. In this paper we present the concept design and energy management of such an integrated energy and mobility system in a real-life environment at the Shell Technology Centre in Amsterdam. Our results show that storage using hydrogen and salt caverns is much cheaper than using large battery storage systems. We also show that the integration of electric vehicles into the electricity network is technically and economically feasible and that they can provide a flexible energy buffer. Ultimately the results of this study show that using both electricity and hydrogen as energy carriers can create a more flexible reliable and cheaper energy system at an office building.