- Home
- A-Z Publications
- Publications
Publications
Safe Operation of Combined Cycle Gas Turbine and Gas Engine Systems Using Hydrogen Rich Fuels
Oct 2015
Publication
This paper describes work performed by a consortium led by the UK Health and Safety Laboratory(HSL)to identify the safe operating conditions for combined cycle power generating systems running on high hydrogen fuels. The work focuses on hydrogen and high hydrogen syngas and biogas waste-stream fuel mixtures which may prove hazardous in the event of a turbine or engine flame out resulting in a flammable fuel mixture entering the hot exhaust system and igniting. The paper describes the project presenting some initial results from this work including the development of large scale experimental facilities on the550 acre HSL site near Buxton Derbyshire UK. It describes the large scale experimental facility which utilises the exhaust gas from a Rolls-Royce Viper jet-engine (converted to run on butane) feeding into a 12 m long 0.60 m diameter instrumented tube at a pre-combustion velocity of 22 m/s. A variable geometry simulated heat exchanger with a 40 %2blockage ratio is present in the tube. Flammable mixtures injected into the tube close to the Viper outlet together with make-up oxygen are then ignited. Extensive optical ionisation temperature and pressure sensors are employed along the length of the tube to measure the pressures and flame speeds resulting from the combustion event. Some preliminary results from the test programme are discussed including deflagration to detonation transitions at high equivalence ratios.
Measurement Challenges for Hydrogen Vehicles
Apr 2019
Publication
Uptake of hydrogen vehicles is an ideal solution for countries that face challenging targets for carbon dioxide reduction. The advantage of hydrogen fuel cell electric vehicles is that they behave in a very similar way to petrol engines yet they do not emit any carbon containing products during operation. The hydrogen industry currently faces the dilemma that they must meet certain measurement requirements (set by European legislation) but cannot do so due to a lack of available methods and standards. This paper outlines the four biggest measurement challenges that are faced by the hydrogen industry including flow metering quality assurance quality control and sampling.
Mixed E-learning and Virtual Reality Pedagogical Approach for Innovative Hydrogen Safety Training for First Responders
Oct 2015
Publication
Within the scope of the HyResponse project the development of a specialised training programme is currently underway. Utilizing an andragogy approach to teaching distance learning is mixed with classroom instructors-led activities while hands-on training on a full-scale simulator is coupled with an innovative virtual reality based experience. Although the course is dedicated mainly to first responders provision has been made to incorporate not only simple table-top and drill exercises but also full-scale training involving all functional emergency response organisations at multi-agency cooperation level. The developed curriculum includes basics of hydrogen safety first responders' procedures and incident management expectations
Metallurgical Model of Diffusible Hydrogen and Non-Metallic Slag Inclusions in Underwater Wet Welding of High-Strength Steel
Nov 2020
Publication
High susceptibility to cold cracking induced by diffusible hydrogen and hydrogen embrittlement are major obstacles to greater utilization of underwater wet welding for high-strength steels. The aim of the research was to develop gas–slag systems for flux-cored wires that have high metallurgical activity in removal of hydrogen and hydroxyl groups. Thermodynamic modeling and experimental research confirmed that a decrease in the concentration of diffusible hydrogen can be achieved by reducing the partial pressure of hydrogen and water vapor in the vapor–gas bubble and by increasing the hydroxyl capacity of the slag system in metallurgical reactions leading to hydrogen fluoride formation and ionic dissolution of hydroxyl groups in the basic fluorine-containing slag of a TiO2–CaF2–Na3AlF6 system.
Research on the Concept of Hydrogen Supply Chains and Power Grids Powered by Renewable Energy Sources: A Scoping Review with the Use of Text Mining
Jan 2022
Publication
The key direction of political actions in the field of sustainable development of the energy sector and economy is the process of energy transformation (decarbonization) and increasing the share of renewable energy sources (RES) in the supply of primary energy. Regardless of the indisputable advantages RES are referred to as unstable energy sources. A possible solution might be the development of the concept of hydrogen supply chains especially the so-called green hydrogen obtained in the process of electrolysis from electricity produced from RES. The aim of the research undertaken in the article is to identify the scope of research carried out in the area of hydrogen supply chains and to link this research with the issues of the operation of electricity distribution networks powered by RES. As a result of the scoping review and the application of the text-mining method using the IRaMuTeQ tool which includes the analysis of the content of 12 review articles presenting the current research achievements in this field over the last three years (2016–2020) it was established that the issues related to hydrogen supply chains including green hydrogen are still not significantly associated with the problem of the operation of power grids. The results of the conducted research allow formulating recommendations for further research areas.
A Developed Plasmatron Design to Enhance Production of Hydrogen in Synthesis Gas Produced by a Fuel Reformer System
Jan 2022
Publication
Feeding IC engines with hydrogen‐rich syngas as an admixture to hydrocarbon fuels can decrease pollutant emissions particularly NOx. It offers a potential technique for low‐environmen‐ tal impact hydrocarbon fuel use in automotive applications. However hydrogen‐rich reformate gas (syngas) production via fuel reforming still needs more research and optimization. In this paper we describe the effect of a plasma torch assembly design on syngas yield and composition during plasma‐assisted reforming of gasoline. Additionally erosion resistance of the cathode‐emitting ma‐ terial under the conditions of gasoline reforming was studied using hafnium metal and lanthanated tungsten alloy. The gasoline reforming was performed with a noncatalytic nonthermal low‐current plasma system in the conditions of partial oxidation in an air and steam mixture. To find the most efficient plasma torch assembly configuration in terms of hydrogen production yield four types of anode design were tested i.e. two types of the swirl ring and two cathode materials while varying the inlet air and fuel flow rates. The experimental results showed that hydrogen was the highest proportion of the produced syngas. The smooth funnel shape anode design in Ring 1 at air/fuel flow rates of 24/4 27/4.5 and 30/5 g/min respectively was more effective than the edged funnel shape. Lanthanated tungsten alloy displayed higher erosion resistance than hafnium metal.
2x40GW Green Hydrogen Initiative
Mar 2020
Publication
Hydrogen will play a pivotal role in achieving an affordable clean and prosperous economy. Hydrogen allows for cost-efficient bulk transport and storage of renewable energy and can decarbonise energy use in all sectors.
The European Union together with North Africa Ukraine and other neighbouring countries have a unique opportunity to realise a green hydrogen system. Europe including Ukraine has good renewable energy resources while North Africa has outstanding and abundant resources. Europe can re-use its gas infrastructure with interconnections to North-Africa and other countries to transport and store hydrogen. And Europe has a globally leading industry for clean hydrogen production especially in electrolyser manufacturing.
If the European Union in close cooperation with its neighbouring countries wants to build on these unique assets and create a world leading industry for renewable hydrogen production the time to act is now. Dedicated and integrated multi GW green hydrogen production plants will thereby unlock the vast renewable energy potential.
We the European hydrogen industry are committed to maintaining a strong and world-leading electrolyser industry and market and to producing renewable hydrogen at equal and eventually lower cost than low-carbon (blue) hydrogen. A prerequisite is that a 2x40 GW electrolyser market in the European Union and its neighbouring countries (e.g. North Africa and Ukraine) will develop as soon as possible.
A roadmap for 40 GW electrolyser capacity in the EU by 2030 shows a 6 GW captive market (hydrogen production at the demand location) and 34 GW hydrogen market (hydrogen production near the resource). A roadmap for 40 GW electrolyser capacity in North Africa and Ukraine by 2030 includes 7.5 GW hydrogen production for the domestic market and a 32.5 GW hydrogen production capacity for export.
If a 2x40 GW electrolyser market in 2030 is realised alongside the required additional renewable energy capacity renewable hydrogen will become cost competitive with fossil (grey) hydrogen. GW-scale electrolysers at wind and solar hydrogen production sites will produce renewable hydrogen cost competitively with low-carbon hydrogen production (1.5-2.0 €/kg) in 2025 and with grey hydrogen (1.0-1.5 €/kg) in 2030.
By realizing 2x40 GW electrolyser capacity producing green hydrogen about 82 million ton CO2 emissions per year could be avoided in the EU. The total investments in electrolyser capacity will be 25-30 billion Euro creating 140000- 170000 jobs in manufacturing and maintenance of 2x40 GW electrolysers.
The industry needs the European Union and its member states to design create and facilitate a hydrogen market infrastructure and economy. Crucial is the design and realisation of new unique and long-lasting mutual co-operation mechanisms on political societal and economic levels between the EU and North Africa Ukraine and other neighbouring countries.
The unique opportunity for the EU and its neighbouring countries to develop a green hydrogen economy will contribute to economic growth the creation of jobs and a sustainable affordable and fair energy system. Building on this position Europe and its neighbours can become world market leaders for green hydrogen production technologies.
The European Union together with North Africa Ukraine and other neighbouring countries have a unique opportunity to realise a green hydrogen system. Europe including Ukraine has good renewable energy resources while North Africa has outstanding and abundant resources. Europe can re-use its gas infrastructure with interconnections to North-Africa and other countries to transport and store hydrogen. And Europe has a globally leading industry for clean hydrogen production especially in electrolyser manufacturing.
If the European Union in close cooperation with its neighbouring countries wants to build on these unique assets and create a world leading industry for renewable hydrogen production the time to act is now. Dedicated and integrated multi GW green hydrogen production plants will thereby unlock the vast renewable energy potential.
We the European hydrogen industry are committed to maintaining a strong and world-leading electrolyser industry and market and to producing renewable hydrogen at equal and eventually lower cost than low-carbon (blue) hydrogen. A prerequisite is that a 2x40 GW electrolyser market in the European Union and its neighbouring countries (e.g. North Africa and Ukraine) will develop as soon as possible.
A roadmap for 40 GW electrolyser capacity in the EU by 2030 shows a 6 GW captive market (hydrogen production at the demand location) and 34 GW hydrogen market (hydrogen production near the resource). A roadmap for 40 GW electrolyser capacity in North Africa and Ukraine by 2030 includes 7.5 GW hydrogen production for the domestic market and a 32.5 GW hydrogen production capacity for export.
If a 2x40 GW electrolyser market in 2030 is realised alongside the required additional renewable energy capacity renewable hydrogen will become cost competitive with fossil (grey) hydrogen. GW-scale electrolysers at wind and solar hydrogen production sites will produce renewable hydrogen cost competitively with low-carbon hydrogen production (1.5-2.0 €/kg) in 2025 and with grey hydrogen (1.0-1.5 €/kg) in 2030.
By realizing 2x40 GW electrolyser capacity producing green hydrogen about 82 million ton CO2 emissions per year could be avoided in the EU. The total investments in electrolyser capacity will be 25-30 billion Euro creating 140000- 170000 jobs in manufacturing and maintenance of 2x40 GW electrolysers.
The industry needs the European Union and its member states to design create and facilitate a hydrogen market infrastructure and economy. Crucial is the design and realisation of new unique and long-lasting mutual co-operation mechanisms on political societal and economic levels between the EU and North Africa Ukraine and other neighbouring countries.
The unique opportunity for the EU and its neighbouring countries to develop a green hydrogen economy will contribute to economic growth the creation of jobs and a sustainable affordable and fair energy system. Building on this position Europe and its neighbours can become world market leaders for green hydrogen production technologies.
Study Navigating the Way to a Renewable Future – Solutions to Decarbonise Shipping
Sep 2019
Publication
On average the shipping sector is responsible for 3% of annual global green-house gas emissions on a CO2-equivalent basis. International shipping represents around 9% of the global emissions associated with the transport sector.<br/>This report from the International Renewable Energy Agency (IRENA) explores the impact of maritime shipping on CO2 emissions the structure of the shipping sector and key areas that need to be addressed to reduce the sector’s carbon footprint.<br/>There is no clear-cut path to decarbonisation. Cutting CO2 emissions in half is therefore likely to require a combination of approaches including the use of alternative fuels upgrading of onshore infrastructure and reducing fuel demand by improving operational performance the report finds.<br/>The shipping sector is strategically important for global efforts against climate change and could be crucial in the long-term shift to a zero-carbon economy. Large-scale deployment of low-carbon fuel infrastructure for shipping could also help to build the necessary momentum to decarbonise other sectors.
Oxford Energy Podcast – Energy Transition Post-Pandemic in the Gulf: Clean Energy, Sustainability and Hydrogen
Jun 2021
Publication
The COVID-19 pandemic has exacerbated challenges faced by hydrocarbon exporters in the Gulf owing to the global push to transition to cleaner energy sources. In this podcast Manal Shehabi (OIES) discusses with David Ledesma a recent OIES-KFAS workshop held in April 2021 titled “Energy Transition Post-Pandemic in the Gulf States” held with support from the Kuwait Foundation for the Advancement of Sciences (KFAS). They discuss separate but interrelated issues on clean energy economic and climate sustainability and hydrogen. Specially they examine how the global energy transition outlook has changed post-pandemic along with its impacts on Gulf States’ economies and energy transition projects. They explain implications to Gulf states’ sustainability evaluating whether these countries are fiscally sustainable post-pandemic and their urgent need for energy and economic diversification. They focus in on the possibility of the Gulf States’ using hydrogen to diversify both in domestic and export markets evaluating opportunities and challenges for both blue and green hydrogen. A preliminary case study on the economics of hydrogen in Kuwait is highlighted as indication of whether Gulf states can produce green hydrogen competitively. They conclude with policy recommendations to increase economic sustainability and resilience post-pandemic both through the energy transition and responses to it.
The podcast can be found on their website
The podcast can be found on their website
A Direct Synthesis of Platinum/Nickel Co-catalysts on Titanium Dioxide Nanotube Surface from Hydrometallurgical-type Process Streams
Aug 2018
Publication
Solutions that simulate hydrometallurgical base metal process streams with high nickel (Ni) and minor platinum (Pt) concentrations were used to create Pt/Ni nanoparticles on TiO2 nanotube surfaces. For this electrochemical deposition – redox replacement (EDRR) was used that also allowed to control the nanoparticle size density and Pt/Ni content of the deposited nanoparticles. The Pt/Ni nanoparticle decorated titanium dioxide nanotubes (TiO2 nanotubes) become strongly activated for photocatalytic hydrogen (H2) evolution. Moreover EDRR facilitates nanoparticle formation without the need for any additional chemicals and is more effective than electrodeposition alone. Actually a 10000-time enrichment level of Pt took place on the TiO2 surface when compared to Pt content in the solution with the EDRR method. The results show that hydrometallurgical streams offer great potential as an alternative raw material source for industrial catalyst production when coupled with redox replacement electrochemistry.
Optimal Operations for Hydrogen-based Energy Storage Systems in Wind Farms via Model Predictive Control
Feb 2021
Publication
Efficient energy production and consumption are fundamental points for reducing carbon emissions that influence climate change. Alternative resources such as renewable energy sources (RESs) used in electricity grids could reduce the environmental impact. Since RESs are inherently unreliable during the last decades the scientific community addressed research efforts to their integration with the main grid by means of properly designed energy storage systems (ESSs). In order to highlight the best performance from these hybrid systems proper design and operations are essential. The purpose of this paper is to present a so-called model predictive controller (MPC) for the optimal operations of grid-connected wind farms with hydrogen-based ESSs and local loads. Such MPC has been designed to take into account the operating and economical costs of the ESS the local load demand and the participation to the electricity market and further it enforces the fulfillment of the physical and the system's dynamics constraints. The dynamics of the hydrogen-based ESS have been modeled by means of the mixed-logic dynamic (MLD) framework in order to capture different behaviors according to the possible operating modes. The purpose is to provide a controller able to cope both with all the main physical and operating constraints of a hydrogen-based storage system including the switching among different modes such as ON OFF STAND-BY and at the same time reduce the management costs and increase the equipment lifesaving. The case study for this paper is a plant under development in the north Norway. Numerical analysis on the related plant data shows the effectiveness of the proposed strategy which manages the plant and commits the equipment so as to preserve the given constraints and save them from unnecessary commutation cycles.
Characteristic of Cryogenic Hydrogen Flames from High-aspect Ratio Nozzles
Sep 2019
Publication
Unintentional leaks at hydrogen fuelling stations have the potential to form hydrogen jet flames which pose a risk to people and infrastructure. The heat flux from these jet flames are often used to develop separation distances between hydrogen components and buildings lot-lines etc. The heat flux and visible flame length is well understood for releases from round nozzles but real unintended releases would be expected to be be higher aspect-ratio cracks. In this work we measured the visible flame length and heat-flux characteristics of cryogenic hydrogen flames from high-aspect ratio nozzles. We compare this data to flames of both cryogenic and compressed hydrogen from round nozzles. The aspect ratio of the release does not affect the flame length or heat flux significantly for a given mass flow under the range of conditions studied. The engineering correlations presented in this work that enable the prediction of flame length and heat flux can be used to assess risk at hydrogen fuelling stations with liquid hydrogen and develop science-based separation distances for these stations.
Framing Policy on Low Emissions Vehicles in Terms of Economic Gains: Might the Most Straightforward Gain be Delivered by Supply Chain Activity to Support Refuelling?
May 2018
Publication
A core theme of the UK Government's new Industrial Strategy is exploiting opportunities for domestic supply chain development. This extends to a special ‘Automotive Sector Deal’ that focuses on the shift to low emissions vehicles (LEVs). Here attention is on electric vehicle and battery production and innovation. In this paper we argue that a more straightforward gain in terms of framing policy around potential economic benefits may be made through supply chain activity to support refuelling of battery/hydrogen vehicles. We set this in the context of LEV refuelling supply chains potentially replicating the strength of domestic upstream linkages observed in the UK electricity and/or gas industries. We use input-output multiplier analysis to deconstruct and assess the structure of these supply chains relative to that of more import-intensive petrol and diesel supply. A crucial multiplier result is that for every £1million of spending on electricity (or gas) 8 full-time equivalent jobs are supported throughout the UK. This compares to less than 3 in the case of petrol/diesel supply. Moreover the importance of service industries becomes apparent with 67% of indirect and induced supply chain employment to support electricity generation being located in services industries. The comparable figure for GDP is 42%.
The Role of Effectiveness Factor on the Modeling of Methanol Steam Reforming Over CuO/ZnO/Al2O3 Catalyst in a Multi-tubular Reactor
Jan 2022
Publication
A pseudo-homogeneous model for the methanol steam reforming process was developed based on reaction kinetics over a CuO/ZnO/Al2O3 catalyst and non-adiabatic heat and mass transfer performances in a co-current packed-bed reactor. A Thiele modulus method and an intraparticle distribution method were applied for predicting the effectiveness factors for main reactions and providing insights into the diffusion-reaction process in a cylindrical catalyst pellet. The results of both methods are validated and show good agreements with the experimental data but the intraparticle distribution method provides better predictions. Results indicate that increases in catalyst size and bulk fluid temperature amplify the impact of intraparticle diffusion limitations showing a decrease in effectiveness factors. To satisfy the requirements of a high temperature polymer electrolyte membrane fuel cell stack the optimized operating conditions which bring the methanol and CO concentrations to less than 1% vol in the reformate stream are determined based on the simulation results.
Magnesium Gasar as a Potential Monolithic Hydrogen Absorbent
Feb 2021
Publication
The study focuses on the aspect of using the structure of gasars i.e. materials with directed open porosity as a potential hydrogen storage. The structure of the tested gasar is composed of a large number of thin open tubular pores running through the entire longitudinal section of the sample. This allows hydrogen to easily penetrate into the entire sample volume. The analysis of pore distribution showed that the longest diffusion path needed for full penetration of the metal structure with hydrogen is about L = 50–70 μm regardless of the external dimensions of the sample. Attempts to hydrogenate the magnesium gasar structure have shown its ability to accumulate hydrogen at a level of 1 wt%. The obtained results were compared with the best result was obtained for the ZK60 alloy after equal channel angular pressing (ECAP) and crushed to a powder form. The result obtained exceeded 4 wt% of hydrogen accumulated in the metal structure at theoretical 6.9 wt% maximum capacity. A model analysis of the theoretic absorption capacity of pure magnesium was also carried out based on the concentration of vacancies in the metal structure. The theoretical results obtained correlate well with experimental data.
Potential Economic Impacts of the HyNet North West Project
Jan 2018
Publication
The objective of the analysis is to provide a robust assessment of the economic impact of HyNet NW over the period to 2050 across both the North West of England and the UK as a whole. Impact is assessed through modelling of direct indirect and induced effect frameworks:
Consideration is also given to the potential impacts of inward investment attracted to the North West/UK in the wake of the Project.
- Direct effects – activities that directly accrue due to the construction and operation of the facilities;
- Indirect effects – the purchase of goods and services to facilitate construction/operation; and
- Induced effects – spending of wages and salaries generated directly and indirectly through construction and operation.
Consideration is also given to the potential impacts of inward investment attracted to the North West/UK in the wake of the Project.
Open-cathode PEMFC Heat Utilisation to Enhance Hydrogen Supply Rate of Metal Hydride Canisters
Mar 2019
Publication
In this paper the hydrogen supply to an open-cathode PEM fuel cell (FC) by using metal hydride (MH) storage and thermal coupling between these two components are investigated theoretically. One of the challenges in using MH hydrogen storage canisters is their limited hydrogen supply rate as the hydrogen release from MH is an endothermic reaction. Therefore in order to meet the required hydrogen supply rate high amounts of MH should be employed that usually suggests storage of hydrogen to be higher than necessary for the application adding to the size weight and cost of the system. On the other hand the exhaust heat (i.e. that is usually wasted if not utilised for this purpose) from open-cathode FCs is a low-grade heat. However this heat can be transferred to MH canisters through convection to heat them up and increase their hydrogen release rate. A mathematical model is used to simulate the heat transfer between PEMFC exhaust heat and MH storage. This enables the prediction of the required MH for different FC power levels with and without heat supply to the MH storage. A 2.5-kW open-cathode FC is used to measure the exhaust air temperature at different output powers. It was found that in the absence of heat supply from the FC to the MH canisters significantly higher number of MH canisters are required to achieve the required rate of hydrogen supply to the FC for sustained operation (specially at high power outputs). However using the exhaust hot air from the FC to supply heat to the MH storage can reduce the number of the MH canisters required by around 40% to 70% for power output levels ranging from 500 W to 2000 W.
Adopting Hydrogen Direct Reduction for the Swedish Steel Industry: A Technological Innovation System (TIS) Study
Sep 2019
Publication
The Swedish steel industry stands before a potential transition to drastically lower its CO2 emissions using direct hydrogen reduction instead of continuing with coke-based blast furnaces. Previous studies have identified hydrogen direct reduction as a promising option. We build upon earlier efforts by performing a technological innovation system study to systematically examine the barriers to a transition to hydrogen direct reduction and by providing deepened quantitative empirics to support the analysis. We also add extended paper and patent analysis methodology which is particularly useful for identifying actors and their interactions in a technological system. We conclude that while the innovation system is currently focused on such a transition notable barriers remain particularly in coordination of the surrounding technical infrastructure and the issue of maintaining legitimacy for such a transition in the likely event that policies to address cost pressures will be required to support this development.
Spatially Resolved Optimization for Studying the Role of Hydrogen for Heat Decarbonization Pathways
Apr 2018
Publication
This paper studies the economic feasibility of installing hydrogen networks for decarbonizing heat in urban areas. The study uses the Heat Infrastructure and Technology (HIT) spatially resolved optimization model to trade-off energy supply infrastructure and end-use technology costs for the most important heat-related energy vectors: gas heat electricity and hydrogen. Two model formulations are applied to a UK urban area: one with an independent hydrogen network and one that allows for retrofitting the gas network into hydrogen. Results show that for average hydrogen price projections cost-effective pathways for heat decarbonization toward 2050 include heat networks supplied by a combination of district-level heat pumps and gas boilers in the domestic and commercial sectors and hydrogen boilers in the domestic sector. For a low hydrogen price scenario when retrofitting the gas network into hydrogen a cost-effective pathway is replacing gas by hydrogen boilers in the commercial sector and a mixture of hydrogen boilers and heat networks supplied by district-level heat pumps gas and hydrogen boilers for the domestic sector. Compared to the first modelled year CO2 emission reductions of 88% are achieved by 2050. These results build on previous research on the role of hydrogen in cost-effective heat decarbonization pathways.
Progress in Catalytic Hydrogen Production from Formic Acid over Supported Metal Complexes
Mar 2021
Publication
Formic acid is a liquid organic hydrogen carrier giving hydrogen on demand using catalysts. Metal complexes are known to be used as efficient catalysts for the hydrogen production from formic acid decomposition. Their performance could be better than those of supported catalysts with metal nanoparticles. However difficulties to separate metal complexes from the reaction mixture limit their industrial applications. This problem can be resolved by supporting metal complexes on the surface of different supports which may additionally provide some surface sites for the formic acid activation. The review analyzes the literature on the application of supported metal complexes in the hydrogen production from formic acid. It shows that the catalytic activity of some stable Ru and Ir supported metal complexes may exceed the activity of homogeneous metal complexes used for deposition. Non-noble metal-based complexes containing Fe demonstrated sufficiently high performance in the reaction; however they can be poisoned by water present in formic acid. The proposed review could be useful for development of novel catalysts for the hydrogen production.
Investigation of Mechanical Tests for Hydrogen Embrittlement in Automotive PHS Steels
Aug 2019
Publication
The problem of hydrogen embrittlement in ultra-high-strength steels is well known. In this study slow strain rate four-point bending and permeation tests were performed with the aim of characterizing innovative materials with an ultimate tensile strength higher than 1000 MPa. Hydrogen uptake in the case of automotive components can take place in many phases of the manufacturing process: during hot stamping due to the presence of moisture in the furnace atmosphere high-temperature dissociation giving rise to atomic hydrogen or also during electrochemical treatments such as cataphoresis. Moreover possible corrosive phenomena could be a source of hydrogen during an automobile’s life. This series of tests was performed here in order to characterize two press-hardened steels (PHS)—USIBOR 1500® and USIBOR 2000®—to establish a correlation between ultimate mechanical properties and critical hydrogen concentration.
Numerical Simulations of Cryogenic Hydrogen Cooling in Vortex Tubes with Smooth Transitions
Mar 2021
Publication
Improving efficiency of hydrogen cooling in cryogenic conditions is important for the wider applications of hydrogen energy systems. The approach investigated in this study is based on a Ranque-Hilsch vortex tube (RHVT) that generates temperature separation in a working fluid. The simplicity of RHVT is also a valuable characteristic for cryogenic systems. In the present work novel shapes of RHVT are computationally investigated with the goal to raise efficiency of the cooling process. Specifically a smooth transition is arranged between a vortex chamber where compressed gas is injected and the main tube with two exit ports at the tube ends. Flow simulations have been carried out using STAR-CCM+ software with the real-gas Redlich-Kwong model for hydrogen at temperatures near 70 K. It is determined that a vortex tube with a smooth transition of moderate size manifests about 7% improvement of the cooling efficiency when compared vortex tubes that use traditional vortex chambers with stepped transitions and a no-chamber setup with direct gas injection.
The Future Potential Hydrogen Demand in Energy-intensive Industries - A Site-specific Approach Applied to Germany
Dec 2021
Publication
Hydrogen when based on renewable electricity can play a key role in the transition towards CO2-neutral industrial production since its use as an energy carrier as well as a feedstock in various industrial process routes is promising. At the same time a large-scale roll-out of hydrogen for industrial use would entail substantial impacts on the energy system which can only be assessed if the regional distribution of future hydrogen demand is considered. Here we assess the technical potential of hydrogen-based technologies for energy-intensive industries in Germany. The site-specific and process-specific bottom-up calculation considers 615 individual plants at 367 sites and results in a total potential hydrogen demand of 326 TWh/a. The results are available as an open dataset. Using hydrogen for non-energy-intensive sectors as well increases the potential hydrogen demand to between 482 and 534 TWh/a for Germany - based on today’s industrial structure and production output. This assumes that fossil fuels are almost completely replaced by hydrogen for process heating and feedstocks. The resulting hydrogen demand is very unevenly distributed: a few sites account for the majority of the overall potential and similarly the bulk of demand is concentrated in a few regions with steel and chemical clusters.
Pressurized Hydrogen from Charged Liquid Organic Hydrogen Carrier Systems by Electrochemical Hydrogen Compression
Feb 2021
Publication
We demonstrate that the combination of hydrogen release from a Liquid Organic Hydrogen Carrier (LOHC) system with electrochemical hydrogen compression (EHC) provides three decisive advantages over the state-of-the-art hydrogen provision from such storage system: a) The EHC device produces reduced hydrogen pressure on its suction side connected to the LOHC dehydrogenation unit thus shifting the thermodynamic equilibrium towards dehydrogenation and accelerating the hydrogen release; b) the EHC device compresses the hydrogen released from the carrier system thus producing high value compressed hydrogen; c) the EHC process is selective for proton transport and thus the process purifies hydrogen from impurities such as traces of methane. We demonstrate this combination for the production of compressed hydrogen (absolute pressure of 6 bar) from perhydro dibenzyltoluene at dehydrogenation temperatures down to 240 °C in a quality suitable for fuel cell operation e.g. in a fuel cell vehicle. The presented technology may be highly attractive for providing compressed hydrogen at future hydrogen filling stations that receive and store hydrogen in a LOHC-bound manner.
Baseload Electricity and Hydrogen Supply Based on Hybrid PV-wind Power Plants
Sep 2019
Publication
The reliable supplies of electricity and hydrogen required for 100% renewable energy systems have been found to be achievable by utilisation of a mix of different resources and storage technologies. In this paper more demanding parameter conditions than hitherto considered are used in measurement of the reliability of variable renewable energy resources. The defined conditions require that supply of baseload electricity (BLEL) and baseload hydrogen (BLH2) occurs solely using cost-optimised configurations of variable photovoltaic solar power onshore wind energy and balancing technologies. The global scenario modelling is based on hourly weather data in a 0.45° × 0.45° spatial resolution. Simulations are conducted for Onsite and Coastal Scenarios from 2020 to 2050 in 10-year time-steps. The results show that for 7% weighted average cost of capital Onsite BLEL can be generated at less than 119 54 41 and 33 €/MWhel in 2020 2030 2040 and 2050 respectively across the best sites with a maximum 20000 TWh annual cumulative generation potential. Up to 20000 TWhH2HHV Onsite BLH2 can be produced at less than 66 48 40 and 35 €/MWhH2HHV in 2020 2030 2040 and 2050 respectively. A partially flexible electricity demand at 8000 FLh could significantly reduce the costs of electricity supply in the studied scenario. Along with battery storage power-to-hydrogen-to-power is found to have a major role in supply of BLEL beyond 2030 as both a daily and seasonal balancing solution. Batteries are not expected to have a significant role in the provision of electricity to water electrolysers.
Hydrogen: A Reviewable Energy Perspective
Sep 2019
Publication
Hydrogen has emerged as an important part of the clean energy mix needed to ensure a sustainable future. Falling costs for hydrogen produced with renewable energy combined with the urgency of cutting greenhouse-gas emissions has given clean hydrogen unprecedented political and business momentum.
This paper from the International Renewable Energy Agency (IRENA) examines the potential of hydrogen fuel for hard-to-decarbonise energy uses including energy-intensive industries trucks aviation shipping and heating applications. But the decarbonisation impact depends on how hydrogen is produced. Current and future sourcing options can be divided into grey (fossil fuel-based) blue (fossil fuel-based production with carbon capture utilisation and storage) and green (renewables-based) hydrogen. Green hydrogen produced through renewable-powered electrolysis is projected to grow rapidly in the coming years.
Among other findings:
Important synergies exist between hydrogen and renewable energy. Hydrogen can boost renewable electricity market growth and broaden the reach of renewable solutions.
Trade of energy-intensive commodities produced with hydrogen including “e-fuels” could spur faster uptake or renewables and bring wider economic benefits.
This paper from the International Renewable Energy Agency (IRENA) examines the potential of hydrogen fuel for hard-to-decarbonise energy uses including energy-intensive industries trucks aviation shipping and heating applications. But the decarbonisation impact depends on how hydrogen is produced. Current and future sourcing options can be divided into grey (fossil fuel-based) blue (fossil fuel-based production with carbon capture utilisation and storage) and green (renewables-based) hydrogen. Green hydrogen produced through renewable-powered electrolysis is projected to grow rapidly in the coming years.
Among other findings:
Important synergies exist between hydrogen and renewable energy. Hydrogen can boost renewable electricity market growth and broaden the reach of renewable solutions.
- Electrolysers can add demand-side flexibility. In advanced European energy markets electrolysers are growing from megawatt to gigawatt scale.
- Blue hydrogen is not inherently carbon free. This type of production requires carbon-dioxide (CO2) monitoring verification and certification.
- Synergies may exist between green and blue hydrogen deployment given the chance for economies of scale in hydrogen use or logistics.
- A hydrogen-based energy transition will not happen overnight. Hydrogen use is likely to catch on for specific target applications. The need for new supply infrastructure could limit hydrogen use to countries adopting this strategy.
- Dedicated hydrogen pipelines have existed for decades and could be refurbished along with existing gas pipelines. The implications of replacing gas abruptly or changing mixtures gradually should be further explored.
Trade of energy-intensive commodities produced with hydrogen including “e-fuels” could spur faster uptake or renewables and bring wider economic benefits.
Gas Detection of Hydrogen/Natural Gas Blends in the Gas Industry
Sep 2019
Publication
A key element in the safe operation of a modern gas distribution system is gas detection. The addition of hydrogen to natural gas will alter the characteristics of the fuel and therefore its impact on gas detection must be considered. It is important that gas detectors remain sufficiently sensitive to the presence of hydrogen and natural gas mixtures and that they do not lead to false readings. This paper presents analyses of work performed as part of the Office for Gas and Energy Markets (OFGEM) funded HyDeploy project on the response of various natural gas industry detectors to blended mixtures up to 20 volume percent (vol%) of hydrogen in natural gas. The scope of the detectors under test included survey instruments and personal monitors that are used in the gas industry. Four blend ratios were analysed (0 10 15 and 20 vol% hydrogen in natural gas). The laboratory testing undertaken investigated the following:
- Flammable response to blends in the ppm range (0-0.2 vol%);
- Flammable response to blends in the lower explosion limit range (0.2-5 vol%);
- Flammable response to blends in the volume percent range (5-100 vol%);
- Oxygen response to blends in the volume percent range (0-25 vol%); and
- Carbon monoxide response to blends in the ppm range (0-1000 ppm).
Hydrogen Permeation Studies of Composite Supported Alumina-carbon Molecular Sieves Membranes: Separation of Diluted Hydrogen from Mixtures with Methane
Jun 2020
Publication
One alternative for the storage and transport of hydrogen is blending a low amount of hydrogen (up to 15 or 20%) into existing natural gas grids. When demanded hydrogen can be then separated close to the end users using membranes. In this work composite alumina carbon molecular sieves membranes (Al-CMSM) supported on tubular porous alumina have been prepared and characterized. Single gas permeation studies showed that the H2/CH4 separation properties at 30 °C are well above the Robeson limit of polymeric membranes. H2 permeation studies of the H2–CH4 mixture gases containing 5–20% of H2 show that the H2 purity depends on the H2 content in the feed and the operating temperature. In the best scenario investigated in this work for samples containing 10% of H2 with an inlet pressure of 7.5 bar and permeated pressure of 0.01 bar at 30 °C the H2 purity obtained was 99.4%.
Review of the Current Status of Ammonia-Blended Hydrogen Fuel Engine Development
Jan 2022
Publication
As fossil fuels continue to be extracted and used issues such as environmental pollution and energy scarcity are surfacing. For the transportation industry the best way to achieve the goal of “carbon neutrality” is to research efficient power systems and develop new alternative fuels. As the world’s largest product of chemicals ammonia is a new renewable fuel with good combustion energy. It can be used as an alternative fuel to reduce carbon emissions because of its proven production process low production and transportation costs safe storage the absence of carbon-containing compounds in its emissions and its future recyclability. This paper firstly introduces the characteristics of ammonia fuel engine and its problems; then it summarizes the effects of various ammonia-blended fuels on the combustion and emission characteristics of the engine from the combustion problem of ammonia-blended engine; then the fuel storage of ammonia-blended hydrogen is discussed the feasibility of hydrogen production instead of hydrogen storage is introduced.
Large-scale Storage of Hydrogen
Mar 2019
Publication
The large-scale storage of hydrogen plays a fundamental role in a potential future hydrogen economy. Although the storage of gaseous hydrogen in salt caverns already is used on a full industrial scale the approach is not applicable in all regions due to varying geological conditions. Therefore other storage methods are necessary. In this article options for the large-scale storage of hydrogen are reviewed and compared based on fundamental thermodynamic and engineering aspects. The application of certain storage technologies such as liquid hydrogen methanol ammonia and dibenzyltoluene is found to be advantageous in terms of storage density cost of storage and safety. The variable costs for these high-density storage technologies are largely associated with a high electricity demand for the storage process or with a high heat demand for the hydrogen release process. If hydrogen is produced via electrolysis and stored during times of low electricity prices in an industrial setting these variable costs may be tolerable.
Direct Ammonia Low-temperature Symmetrical Solid Oxide Fuel Cells with Composite Semiconductor Electrolyte
Jan 2022
Publication
In this work a low-temperature symmetrical solid oxide fuel cell with Ni-NCAL|SDC/NCAL|Ni-NCAL (70 SDC:30 NCAL) configuration was successfully constructed by a simple dry press method. At 500 and 550 ◦C the peak power densities of the cell in ammonia were 501 and 755 mW cm− 2 and in hydrogen were 670 and 895 mW cm− 2 respectively. EIS data showed that the Rp values of the cell in ammonia and hydrogen at 550 ◦C were 0.250 and 0.246 Ω cm− 2 respectively indicating the excellent catalytic activity of the Ni-NCAL electrode toward ammonia decomposition and hydrogen oxidation. The different cell output can be ascribed to additional ammonia decomposition steps compared to hydrogen. The noticeable reaction product on the surface of the Ni foam was detrimental to ammonia decomposition. In summary a symmetrical cell with SDC/NCAL semi-conductor electrolyte and Ni-NCAL electrodes exhibited higher electrochemical performance at low temperature than the results reported to date. Therefore higher electrochemical performance can be expected from this cell configuration with more efficient ammonia decomposition catalysts.
Sustainable Hydrogen Production: A Role for Fusion
Apr 2007
Publication
This Meeting Report summarises the findings of a two-day workshop in April 2007 at the Culham Science Centre and Worcester College Oxford which explored the potential for large-scale Hydrogen production through methods other than electrolysis.<br/>Operating at the cusp of research and policy-making the UK Energy Research Centre's mission is to be the UK's pre-eminent centre of research and source of authoritative information and leadership on sustainable energy systems. The Centre takes a whole systems approach to energy research incorporating economics engineering and the physical environmental and social sciences while developing and maintaining the means to enable cohesive research in energy. A key supporting function of UKERC is the Meeting Place based in Oxford which aims to bring together members of the UK energy community and overseas experts from different disciplines to learn identify problems develop solutions and further the energy debate.
Scottish Hydrogen Assessment
Dec 2020
Publication
During 2020 the Scottish Government in partnership with Highlands and Islands Enterprise and Scottish Enterprise commissioned Arup and E4Tech to carry out a hydrogen assessment to deepen our evidence base in order to inform our policies on hydrogen going forward. The assessment aims to investigate how and where hydrogen may fit within the evolving energy system technically geographically and economically. To assist in this consideration a key part of the Hydrogen Assessment is the development of distinct viable scenarios for hydrogen deployment in Scotland and the economic assessment of those scenarios.<br/>From our assessment it is clear that hydrogen is not just an energy and emissions reduction opportunity; it could also have an important role in generating new economic opportunities in Scotland. The assessment forms an important part of the evidence base that informed the development of the Hydrogen Policy Statement.
Five Minute Guide to Hydrogen
Feb 2016
Publication
Hydrogen is an emerging energy vector many components of which are mature technologies. Current hydrogen technology is already able to provide advantages over other energy vectors and many of its challenges are being actively addressed by research and development.<br/><br/>Hydrogen can be derived stored and converted through various processes each of which represents different levels of carbon intensity efficiency and end use functionality. Our latest five minute guide looks at this energy vector in brief including public perception transportation and storage as well as using hydrogen as a solution.
Hydrolysis-Based Hydrogen Generation Investigation of Aluminium System Adding Low-Melting Metals
Mar 2021
Publication
In this age of human civilization there is a need for more efficient cleaner and renewable energy as opposed to that provided by nonrenewable sources such as coal and oil. In this sense hydrogen energy has been proven to be a better choice. In this paper a portable graphite crucible metal smelting furnace was used to prepare ten multi-element aluminum alloy ingots with different components. The microstructure and phase composition of the ingots and reaction products were analyzed by X-ray diffraction (XRD) scanning electron microscopy (SEM) and differential scanning calorimetry (DSC). The reaction was carried out in a constant temperature water bath furnace at 60°C and the hydrogen production performance of the multi-element aluminum alloys in different proportions was compared by the drainage gas collection method. The experimental results show that the as-cast microstructure of Al–Ga–In–Sn aluminum alloy is composed of a solid solution of Al and part of Ga and a second phase of In3Sn. After the hydrolysis reaction the products were dried at 150°C and then analyzed by XRD. The products were mainly composed of AlOOH and In3Sn. Alloys with different compositions react at the same hydrolysis temperature and the hydrogen production performance is related to the ratio of low-melting-point metal elements. By comparing two different ratios of Ga–In–Sn (GIS) the hydrogen production capacity and production rate when the ratio is 6:3:1 are generally higher than those when the ratio is 7:2:1. The second phase content affects the hydrogen production performance.
Review and Assessment of the Effect of Hydrogen Gas Pressure on the Embrittlement of Steels in Gaseous Hydrogen Environment
Apr 2021
Publication
Hydrogen gas pressure is an important test parameter when considering materials for high-pressure hydrogen applications. A large set of data on the effect of hydrogen gas pressure on mechanical properties in gaseous hydrogen experiments was reviewed. The data were analyzed by converting pressures into fugacities (f) and by fitting the data using an f|n| power law. For 95% of the data sets |n| was smaller than 0.37 which was discussed in the context of (i) rate-limiting steps in the hydrogen reaction chain and (ii) statistical aspects. This analysis might contribute to defining the appropriate test fugacities (pressures) to qualify materials for gaseous hydrogen applications.
Scottish Offshore Wind to Green Hydrogen Opportunity Assessment
Dec 2020
Publication
Initial assessment of Scotland’s opportunity to produce green hydrogen from offshore wind
Summary of Key Findings
Summary of Key Findings
- Scotland has an abundant offshore wind resource that has the potential to be a vital component in our net zero transition. If used to produce green hydrogen offshore wind can help abate the emissions of historically challenging sectors such as heating transport and industry.
- The production of green hydrogen from offshore wind can help overcome Scotland’s grid constraints and unlock a massive clean power generation resource creating a clean fuel for Scottish industry and households and a highly valuable commodity to supply rapidly growing UK and European markets.
- The primary export markets for Scottish green hydrogen are expected to be in Northern Europe (Germany Netherlands & Belgium). Strong competition to supply these markets is expected to come from green hydrogen produced from solar energy in Southern Europe and North Africa.
- Falling wind and electrolyser costs will enable green hydrogen production to be cost-competitive in the key transport and heat sectors by 2032. Strategic investment in hydrogen transportation and storage is essential to unlocking the economic opportunity for Scotland.
- Xodus’ analysis supports a long-term outlook of LCoH falling towards £2/kg with an estimated reference cost of £2.3 /kg in 2032 for hydrogen delivered to shore.
- Scotland has extensive port and pipeline infrastructure that can be repurposed for hydrogen export to the rest of UK and to Europe. Pipelines from the ‘90s are optimal for this purpose as they are likely to retain acceptable mechanical integrity and have a metallurgy better suited to hydrogen service. A more detailed assessment of export options should be performed to provide a firm foundation for early commercial green hydrogen projects.
- There is considerable hydrogen supply chain overlap with elements of parallel sectors most notably the oil and gas offshore wind and subsea engineering sectors. Scotland already has a mature hydrocarbon supply chain which is engaged in supporting green hydrogen. However a steady pipeline of early projects supported by a clear financeable route to market will be needed to secure this supply chain capability through to widescale commercial deployment.
- There are gaps in the Scottish supply chain in the areas of design manufacture and maintenance of hydrogen production storage and transportation systems. Support including apprenticeships will be needed to develop indigenous skills and capabilities in these areas.
- The development of green hydrogen from offshore wind has the potential to create high value jobs a significant proportion which are likely to be in remote rural/coastal communities located close to offshore wind resources. These can serve as an avenue for workers to redeploy and develop skills learned from oil and gas in line with Just Transition principles.
Opportunities and Challenges for Thermally Driven Hydrogen Production Using Reverse Electrodialysis System
Jul 2019
Publication
Ongoing and emerging renewable energy technologies mainly produce electric energy and intermittent power. As the energy economy relies on banking energy there is a rising need for chemically stored energy. We propose heat driven reverse electrodialysis (RED) technology with ammonium bicarbonate (AmB) as salt for producing hydrogen. The study provides the authors’ perspective on the commercial feasibility of AmB RED for low grade waste heat (333 K–413 K) to electricity conversion system. This is to our best of knowledge the only existing study to evaluate levelized cost of energy of a RED system for hydrogen production. The economic assessment includes a parametric study and a scenario analysis of AmB RED system for hydrogen production. The impact of various parameters including membrane cost membrane lifetime cost of heating inter-membrane distance and residence time are studied. The results from the economic study suggests RED system with membrane cost less than 2.86 €/m2 membrane life more than 7 years and a production rate of 1.19 mol/m2/h or more are necessary for RED to be economically competitive with the current renewable technologies for hydrogen production. Further salt solubility residence time and inter-membrane distance were found to have impact on levelized cost of hydrogen LCH. In the present state use of ammonium bicarbonate in RED system for hydrogen production is uneconomical. This may be attributed to high membrane cost low (0.72 mol/m2/h) hydrogen production rate and large (1281436 m2) membrane area requirements. There are three scenarios presented the present scenario market scenario and future scenario. From the scenario analysis it is clear that membrane cost and membrane life in present scenario controls the levelized cost of hydrogen. In market scenario and future scenario the hydrogen production rate (which depends on membrane properties inter-membrane distance etc.) the cost of regeneration system and the cost of heating controls the levelized cost of hydrogen. For a thermally driven RED system to be economically feasible the membrane cost not more than 20 €/m2; hydrogen production rate of 3.7 mol/m2/h or higher and cost of heating not more than 0.03 €/kWh for low grade waste heat to hydrogen production.
Workshop Report: Summary & Outcomes, Putting Science into Standards Power-to-Hydrogen and HCNG
Oct 2014
Publication
The Joint Research Centre (JRC) of the European Commission together with the European Association of Research and Technology Organisations (EARTO) the European Standards Organisations (ESO) CEN and CENELEC and the European Commission Directorate-General Enterprise and Industry (ENTR) have launched an initiative within the context of the European Forum on Science and Industry to bring the scientific and standardization communities closer together. The second and very successful workshop in a series entitled “Putting Science into Standards" was held in at the Institute for Energy and Transport of the JRC in Petten on 21-22 October 2014.<br/>The workshop focused on Power to Hydrogen (P2H) and Hydrogen Compressed Natural Gas (HCNG) which represent a promising and major contribution to the challenging management of increased integration of renewable energy sources in the overall energy system. The workshop offered a platform to exchange ideas on technologies policy and standardization issues. The participation of major stakeholders from both industry and research to this event proved fruitful in moving towards consensus on the relevant technical issues involved and at identifying a common way forward to increase the maturity and market visibility of P2H components and systems. Other outcomes include a clarification of expectations of industry of where and how policy and standardization can contribute to a competitive development of P2H and related issues. The workshop results will be used to devise a roadmap on "Opportunities for Power to Hydrogen and HCNG" by CEN/CENELEC outlining the next steps of standardization activities.
The Role of the Substrate on the Mechanical and Thermal Stability of Pd Thin Films During Hydrogen (De)sorption
Nov 2020
Publication
In this work we studied the mechanical and thermal stability of ~100 nm Pd thin films magnetron sputter deposited on a bare oxidized Si(100) wafer a sputtered Titanium (Ti) intermediate layer and a spin-coated Polyimide (PI) intermediate layer. The dependence of the film stability on the film morphology and the film-substrate interaction was investigated. It was shown that a columnar morphology with elongated voids at part of the grain boundaries is resistant to embrittlement induced by the hydride formation (α↔β phase transitions). For compact film morphology depending on the rigidity of the intermediate layer and the adherence to the substrate complete transformation (Pd-PI-SiO2/Si) or partly suppression (Pd-Ti-SiO2/Si) of the α to β-phase was observed. In the case of Pd without intermediate layer (Pd-SiO2/Si) buckling delamination occurred. The damage and deformation mechanisms could be understood by the analysis of the stresses and dislocation (defects) behavior near grain boundaries and the film-substrate interface. From diffraction line-broadening combined with microscopy analysis we showed that in Pd thin films stresses relax at critical stress values via different relaxation pathways depending on film-microstructure and film-substrate interaction. On the basis of the in-situ hydriding experiments it was concluded that a Pd film on a flexible PI intermediate layer exhibits free-standing film-like behavior besides being strongly clamped on a stiff SiO2/Si substrate.
Energy Technology Perspectives 2020- Special Report on Carbon Capture Utilisation and Storage
Sep 2020
Publication
Energy Technology Perspectives 2020 is a major new IEA publication focused on the technology needs and opportunities for reaching international climate and sustainable energy goals. This flagship report offers vital analysis and advice on the clean energy technologies the world needs to meet net-zero emissions objectives.
The report’s comprehensive analysis maps out the technologies needed to tackle emissions in all parts of the energy sector including areas where technology progress is still lacking such as long-distance transport and heavy industries. It shows the amount of emissions reductions that are required from electrification hydrogen bioenergy and carbon capture utilisation and storage. It also provides an assessment of emissions from existing infrastructure and what can be done to address them.
Link to Document on IEA website
The report’s comprehensive analysis maps out the technologies needed to tackle emissions in all parts of the energy sector including areas where technology progress is still lacking such as long-distance transport and heavy industries. It shows the amount of emissions reductions that are required from electrification hydrogen bioenergy and carbon capture utilisation and storage. It also provides an assessment of emissions from existing infrastructure and what can be done to address them.
Link to Document on IEA website
Hydrogen for Cooking: A Review of Cooking Technologies, Renewable Hydrogen Systems and Techno-Economics
Dec 2022
Publication
About 3 billion people use conventional carbon-based fuels such as wood charcoal and animal dung for their daily cooking needs. Cooking with biomass causes deforestation and habitat loss emissions of greenhouse gases and smoke pollution that affects people’s health and well-being. Hydrogen can play a role in enabling clean and safe cooking by reducing household air pollution and reducing greenhouse gas emissions. This first-of-a-kind review study on cooking with hydrogen assessed existing cooking technologies and hydrogen systems in developing country contexts. Our critical assessment also included the modelling and experimental studies on hydrogen. Renewable hydrogen systems and their adoptability in developing countries were analysed. Finally we presented a scenario for hydrogen production pathways in developing countries. Our findings indicated that hydrogen is attractive and can be safely used as a cooking fuel. However radical and disruptive models are necessary to transform the traditional cooking landscape. There is a need to develop global south-based hydrogen models that emphasize adoptability and capture the challenges in developing countries. In addition the techno-economic assumptions of the models vary significantly leading to a wide-ranging levelized cost of electricity. This finding underscored the necessity to use comprehensive techno-economic assumptions that can accurately predict hydrogen costs.
Establishing a Hydrogen Economy: The Future of Energy 2035
May 2019
Publication
The next few decades are expected to be among the most transformative the energy sector has ever seen. Arup envisages a world with a much more diverse range of heating sources and with significantly lower emissions and renewable energy powering transport.<br/>As part of this the establishment of a strong hydrogen economy is a very real opportunity and is within reaching distance. Our report uses the UK as a case study example and explores the challenges and opportunities for hydrogen in the context of the whole energy system.<br/>Read about the progress already being made in using hydrogen for transport and heat. And the need to progress policy and collaboration between government the private sector and other stakeholders to shape future demand change consumer perception and create the strong supply chains needed to allow the hydrogen economy to thrive.
Mechanism of Action of Polytetrafluoroethylene Binder on the Performance and Durability of High-temperature Polymer Electrolyte Fuel Cells
Feb 2021
Publication
In this work new insights into impacts of the polytetrafluoroethylene (PTFE) binder on high temperature polymer electrolyte fuel cells (HT-PEFCs) are provided by means of various characterizations and accelerated stress tests. Cathodes with PTFE contents from 0 wt% to 60 wt% were fabricated and compared using electrochemical measurements. The results indicate that the cell with 10 wt% PTFE in the cathode catalyst layer (CCL) shows the best performance due to having the lowest mass transport resistance and cathode protonic resistance. Moreover cyclic voltammograms show that Pt (100) edge and corner sites are significantly covered by PTFE and phosphate anions when the PTFE content is higher than 25 wt%. Open-circuit and low load-cycling conditions are applied to accelerate degradation processes of the HT-PEFCs. The PTFE binder shows a network structure in the pores of the catalyst layer which reduces phosphoric acid leaching during the aging tests. In addition the high binder HT-PEFCs more easily suffer from a mass transport problem leading to more severe performance degradation.
Green Hydrogen in the UK: Progress and Prospects
Apr 2022
Publication
Green hydrogen has been known in the UK since Robert Boyle described flammable air in 1671. This paper describes how green hydrogen has become a new priority for the UK in 2021 beginning to replace fossil hydrogen production exceeding 1 Mte in 2021 when the British Government started to inject significant funding into green hydrogen sources though much less than the USA Germany Japan and China. Recent progress in the UK was initiated in 2008 when the first UK green hydrogen station opened in Birmingham University refuelling 5 hydrogen fuel cell battery electric vehicles (HFCBEVs) for the 50 PhD chemical engineering students that arrived in 2009. Only 10 kg/day were required in contrast to the first large green ITM power station delivering almost 600 kg/day of green hydrogen that opened in the UK in Tyseley in July 2021. The first question asked in this paper is: ‘What do you mean Green?’. Then the Clean Air Zone (CAZ) in Birmingham is described with the key innovations defined. Progress in UK green hydrogen and fuel cell introduction is then recounted. The remarks of Elon Musk about this ‘Fool Cell; Mind bogglingly stupid’ technology are analysed to show that he is incorrect. The immediate deployment of green hydrogen stations around the UK has been planned. Another century may be needed to make green hydrogen dominant across the country yet we will be on the correct path once a profitable supply chain is established in 2022.
Can Industry Keep Gas Distribution Networks Alive? Future Development of the Gas Network in a Decarbonized World: A German Case Study
Dec 2022
Publication
With the growing need for decarbonization the future gas demand will decrease and the necessity of a gas distribution network is at stake. A remaining industrial gas demand on the distribution network level could lead to industry becoming the main gas consumer supplied by the gas distribution network leading to the question: can industry keep the gas distribution network alive? To answer this research question a three-stage analysis was conducted starting from a rough estimate of average gas demand per production site and then increasing the level of detail. This paper shows that about one third of the German industry sites investigated are currently supplied by the gas distribution network. While the steel industry offers new opportunities the food and tobacco industry alone cannot sustain the gas distribution network by itself.
Hydrogen Ventilation Test Facility or Underground Mining and Tunneling
Sep 2019
Publication
One of the focus areas in the heavy-duty transport industry globally is de-carbonization of trucks dozers shovels semi-trucks buses etc. Hydrogen fuel cells (FCs) technology is one considered solution for the industry due to its zero-emissions its MW scalability and capacity to store large amounts of energy for long duration continuous power operation. Underground deep mines is another option for deployment and operation of hydrogen FCs. Benefits include lower emissions improved health comfort and safety as well as reduced operating costs. Underground mining trucks loaders and other machines have power ratings up to 750 kW which proves difficult for battery and tethered electric energy. Hydrogen FCs have the ability to overcome these power and energy storage limitations. The risks and technologies associated with delivering storing and using hydrogen underground first need to be investigated and proven safe. This work presents the design construction and operation of a mining ventilation test facility (VTF) at the North-West University in South Africa that aims to quantify the risk of hydrogen in confined ventilated environments. Initial work has been conducted on measuring concentrations of hydrogen released in the temporary ventilation site and is discussed.
A Study on the Characteristics of Academic Topics Related to Renewable Energy Using the Structural Topic Modelling and the Weak Signal Concept
Mar 2021
Publication
It is important to examine in detail how the distribution of academic research topics related to renewable energy is structured and which topics are likely to receive new attention in the future in order for scientists to contribute to the development of renewable energy. This study uses an advanced probabilistic topic modeling to statistically examine the temporal changes of renewable energy topics by using academic abstracts from 2010–2019 and explores the properties of the topics from the perspective of future signs such as weak signals. As a result in strong signals methods for optimally integrating renewable energy into the power grid are paid great attention. In weak signals interest in large-capacity energy storage systems such as hydrogen supercapacitors and compressed air energy storage showed a high rate of increase. In not-strong-but-well-known signals comprehensive topics have been included such as renewable energy potential barriers and policies. The approach of this study is applicable not only to renewable energy but also to other subjects.
Net Zero Review: Interim Report
Dec 2020
Publication
Climate change is an existential threat to humanity. Without global action to limit greenhouse gas emissions the climate will change catastrophically with almost unimaginable consequences for societies across the world. In recognition of the risks to the UK and other countries the UK became in 2019 the first major economy to implement a legally binding net zero target.<br/>The UK has made significant progress in decarbonising its economy but needs to go much further to achieve net zero. This will be a collective effort requiring changes from households businesses and government. It will require substantial investment and significant changes to how people live their lives.<br/>This transformation will also create opportunities for the UK economy. New industries and jobs will emerge as existing sectors decarbonise or give way to lowcarbon equivalents. The Ten Point Plan for a Green Industrial Revolution and Energy White Paper start to set out how the UK can make the most of these opportunities with new investment in sectors like offshore wind and hydrogen.1 The transition will also have distributional and competitiveness impacts that the government will need to consider as it designs policy.<br/>This interim report sets out the analysis so far from the Treasury’s Net Zero Review and seeks feedback on the approach ahead of the final report due to be published next year.
Synthesis and Characterisation of Platinum-cobalt-manganese Ternary Alloy Catalysts Supported on Carbon Nanofibers: An Alternative Catalyst for Hydrogen Evolution Reaction
Mar 2020
Publication
A systematic method for obtaining a novel electrode structure based on PtCoMn ternary alloy catalyst supported on graphitic carbon nanofibers (CNF) for hydrogen evolution reaction (HER) in acidic media is proposed. Ternary alloy nanoparticles (Co0.6Mn0.4 Pt) with a mean crystallite diameter under 10 nm were electrodeposited onto a graphitic support material using a two-step pulsed deposition technique. Initially a surface functionalisation of the carbon nanofibers is performed with the aid of oxygen plasma. Subsequently a short galvanostatic pulse electrodeposition technique is applied. It has been demonstrated that if pulsing current is employed compositionally controlled PtCoMn catalysts can be achieved. Variations of metal concentration ratios in the electrolyte and main deposition parameters such as current density and pulse shape led to electrodes with relevant catalytic activity towards HER. The samples were further characterised using several physico-chemical methods to reveal their morphology structure chemical and electrochemical properties. X-ray diffraction confirms the PtCoMn alloy formation on the graphitic support and energy dispersive X-ray spectroscopy highlights the presence of the three metallic components from the alloy structure. The preliminary tests regarding the electrocatalytic activity of the developed electrodes display promising results compared to commercial Pt/C catalysts. The PtCoMn/CNF electrode exhibits a decrease in hydrogen evolution overpotential of about 250 mV at 40 mA cm−2 in acidic solution (0.5 M H2SO4) when compared to similar platinum based electrodes (Pt/CNF) and a Tafel slope of around 120 mV dec−1 indicating that HER takes place under the Volmer-Heyrovsky mechanismm
No more items...