Production & Supply Chain
Electrolyzer Array Alternate Control Strategy Considering Wind Power Prediction
Aug 2022
Publication
Non grid connected wind power hydrogen production technology is of great significance for the large-scale comprehensive utilization of hydrogen energy and accelerating the development of clean energy. In this paper an electrolyzer power allocation and alternate control method for non grid connected wind power hydrogen production is proposed and the optimized control strategy are combined to predict the maximum wind power of certain time interval. While retaining the required data characteristics the instantaneous fluctuation of some wind power data is eliminated which provides a reliable basis for power distribution in the alternation control strategy of electrolyzer array. The case simulation verifies the effectiveness of the electrolyzer array control principle and the prediction of the maximum wind power. While ensuring the absorption effect and hydrogen production rate the service life and operation safety of the electrolyzer array are effectively improved by balancing the working state of each electrolyzer.
A Simulation Study on Evaluating the Influence of Impurities on Hydrogen Production in Geological Carbon Dioxide Storage
Sep 2023
Publication
In this study we examined the effect of CO2 injection into deep saline aquifers considering impurities present in blue hydrogen production. A fluid model was designed for reservoir conditions with impurity concentrations of 3.5 and 20%. The results showed that methane caused density decreases of 95.16 and 76.16% at 3.5 and 20% respectively whereas H2S caused decreases of 99.56 and 98.77% respectively. Viscosity decreased from 0.045 to 0.037 cp with increasing methane content up to 20%; however H2S did not affect the viscosity. Notably CO2 with H2S impacted these properties less than methane. Our simulation model was based on the Gorae-V properties and simulated injections for 10 years followed by 100 years of monitoring. Compared with the pure CO2 injection methane reached its maximum pressure after eight years and eleven months at 3.5% and eight years at 20% whereas H2S reached maximum pressure after nine years and two months and nine years and six months respectively. These timings affected the amount of CO2 injected. With methane as an impurity injection efficiency decreased up to 73.16% whereas with H2S it decreased up to 81.99% with increasing impurity concentration. The efficiency of CO2 storage in the dissolution and residual traps was analyzed to examine the impact of impurities. The residual trap efficiency consistently decreased with methane but increased with H2S. At 20% concentration the methane trap exhibited higher efficiency at the end of injection; however H2S had a higher efficiency at the monitoring endpoint. In carbon capture and storage projects methane impurities require removal whereas H2S may not necessitate desulfurization due to its minimal impact on CO2 storage efficiency. Thus the application of carbon capture and storage (CCS) to CO2 emissions containing H2S as an impurity may enable economically viable operations by reducing additional costs.
Open-source Project Feasibility Tools for Supporting Development of the Green Ammonia Value Chain
Nov 2022
Publication
Ammonia plays a vital role in feeding the world through fertilizer production as well as having other industrial uses. However current ammonia production processes rely heavily on fossil fuels mostly natural gas to generate hydrogen as a feedstock. There is an urgent need to re-design and decarbonise the production process to reduce greenhouse emissions and avoid dependence on volatile gas markets and a depleting resource base. Renewable energy driven electrolysis to generate hydrogen provides a viable pathway for producing carbon-free or green ammonia. However a key challenge associated with producing green ammonia is managing low cost but highly variable wind and solar renewable energy generation for hydrogen electrolysis while maintaining reliable operation of the less flexible ammonia synthesis unit. To date green ammonia production has only been demonstrated at pilot scale and optimising plant configurations and scaling up production facilities is an urgent task. Existing feasibility studies have demonstrated the ability to model and cost green ammonia production pathways that can overcome the technical and economic challenges. However these existing approaches are context specific demonstrating the ability to model and cost green ammonia production for defined locations with set configurations. In this paper we present a modelling framework that consolidates the array of configurations previously studied into a single framework that can be tailored to the location of interest. Our open-source green ammonia modelling and costing tool dynamically simulates the integration of renewable energy with a wide range of balancing power and storage options to meet the flexible demands of the green ammonia production process at hourly time resolution over a year or more. Unlike existing models the open-source implementation of our tool allows it to be used by a potentially wide range of stakeholders to explore their own projects and help guide the upscaling of green ammonia as a pathway for decarbonisation. Using Gladstone in Australia as a case study a 1 million tonne per annum (MMTPA) green ammonia plant is modelled and costed using price assumptions for major equipment in 2030 provided by the Australian Energy Market Operator (AEMO). Using a hybrid (solar PV and wind) renewable energy source and Battery Energy Storage System as balancing technology we estimate a levelized cost of ammonia (LCOA) between 0.69 and 0.92 USD kgNH3 -1 . While greater than historical ammonia production costs from natural gas falling renewables costs and emission reduction imperatives suggest a major future role for green ammonia.
Green Hydrogen Production through Ammonia Decomposition Using Non-Thermal Plasma
Sep 2023
Publication
Liquid hydrogen carriers will soon play a significant role in transporting energy. The key factors that are considered when assessing the applicability of ammonia cracking in large-scale projects are as follows: high energy density easy storage and distribution the simplicity of the overall process and a low or zero-carbon footprint. Thermal systems used for recovering H2 from ammonia require a reaction unit and catalyst that operates at a high temperature (550–800 ◦C) for the complete conversion of ammonia which has a negative effect on the economics of the process. A non-thermal plasma (NTP) solution is the answer to this problem. Ammonia becomes a reliable hydrogen carrier and in combination with NTP offers the high conversion of the dehydrogenation process at a relatively low temperature so that zero-carbon pure hydrogen can be transported over long distances. This paper provides a critical overview of ammonia decomposition systems that focus on non-thermal methods especially under plasma conditions. The review shows that the process has various positive aspects and is an innovative process that has only been reported to a limited extent.
Thermocatalytic Hydrogen Production Through Decomposition of Methane-A Review
Oct 2021
Publication
Consumption of fossil fuels especially in transport and energy-dependent sectors has led to large greenhouse gas production. Hydrogen is an exciting energy source that can serve our energy purposes and decrease toxic waste production. Decomposition of methane yields hydrogen devoid of COx components thereby aiding as an eco-friendly approach towards large-scale hydrogen production. This review article is focused on hydrogen production through thermocatalytic methane decomposition (TMD) for hydrogen production. The thermodynamics of this approach has been highlighted. Various methods of hydrogen production from fossil fuels and renewable resources were discussed. Methods including steam methane reforming partial oxidation of methane auto thermal reforming direct biomass gasification thermal water splitting methane pyrolysis aqueous reforming and coal gasification have been reported in this article. A detailed overview of the different types of catalysts available the reasons behind their deactivation and their possible regeneration methods were discussed. Finally we presented the challenges and future perspectives for hydrogen production via TMD. This review concluded that among all catalysts nickel ruthenium and platinum-based catalysts show the highest activity and catalytic efficiency and gave carbon-free hydrogen products during the TMD process. However their rapid deactivation at high temperatures still needs the attention of the scientific community.
Hydrogen Production by Solar Thermochemical Water-Splitting Cycle via a Beam Down Concentrator
May 2021
Publication
About 95% of the hydrogen presently produced is from natural gas and coal and the remaining 5% is generated as a by-product from the production of chlorine through electrolysis1 . In the hydrogen economy (Crabtree et al. 2004; Penner 2006; Marbán and Valdés-Solís 2007) hydrogen is produced entirely from renewable energy. The easiest approach to advance renewable energy production is through solar photovoltaic and electrolysis a pathway of high technology readiness level (TRL) suffering however from two downfalls. First of all electricity is already an energy carrier and transformation with a penalty into another energy carrier hydrogen is in principle flawed. The second problem is that the efficiency of commercial solar panels is relatively low. The cadmium telluride (CdTe) thin-film solar cells have a solar energy conversion efficiency of 17%. Production of hydrogen using the current best processes for water electrolysis has an efficiency of ∼70%. As here explained the concentrated solar energy may be used to produce hydrogen using thermochemical water-splitting cycles at much global higher efficiency (fuel energy to incident sun energy). This research and development (R&D) effort is therefore undertaken to increase the TRL of this approach as a viable and economical option.
A Green Route for Hydrogen Producton from Alkaline Thermal Treatment (ATT) of Biomass with Carbon Storage
Apr 2023
Publication
Hydrogen a green energy carrier is one of the most promising energy sources. However,it is currently mainly produced from depleting fossil fuels with high carbon emissions which has serious negative effects on the economy and environment. To address this issue sustainable hydrogen production from bio-energy with carbon capture and storage (HyBECCS) is an ideal technology to reduce global carbon emissions while meeting energy demand. This review presents an overview of the latest progress in alkaline thermal treatment (ATT) of biomass for hydrogen production with carbon storage especially focusing on the technical characteristics and related challenges from an industrial application perspective. Additionally the roles of alkali and catalyst in the ATT process are critically discussed and several aspects that have great influences on the ATT process such as biomass types reaction parameters and reactors are expounded. Finally the potential solutions to the general challenges and obstacles to the future industrial-scale application of ATT of biomass for hydrogen production are proposed.
Hydrogen Production by Water Electrolysis Technologies: A Review
Sep 2023
Publication
Hydrogen as an energy source has been identified as an optimal pathway for mitigating climate change by combining renewable electricity with water electrolysis systems. Proton exchange membrane (PEM) technology has received a substantial amount of attention because of its ability to efficiently produce high-purity hydrogen while minimising challenges associated with handling and maintenance. Another hydrogen generation technology alkaline water electrolysis (AWE) has been widely used in commercial hydrogen production applications. Anion exchange membrane (AEM) technology can produce hydrogen at relatively low costs because the noble metal catalysts used in PEM and AWE systems are replaced with conventional low-cost electrocatalysts. Solid oxide electrolyzer cell (SOEC) technology is another electrolysis technology for producing hydrogen at relatively high conversion efficiencies low cost and with low associated emissions. However the operating temperatures of SOECs are high which necessitates long startup times. This review addresses the current state of technologies capable of using impure water in water electrolysis systems. Commercially available water electrolysis systems were extensively discussed and compared. The technical barriers of hydrogen production by PEM and AEM were also investigated. Furthermore commercial PEM stack electrolyzer performance was evaluated using artificial river water (soft water). An integrated system approach was recommended for meeting the power and pure water demands using reversible seawater by combining renewable electricity water electrolysis and fuel cells. AEM performance was considered to be low requiring further developments to enhance the membrane’s lifetime.
Comparative Exergy and Environmental Assessment of the Residual Biomass Gasification Routes for Hydrogen and Ammonia Production
Jul 2023
Publication
The need to reduce the dependency of chemicals on fossil fuels has recently motivated the adoption of renewable energies in those sectors. In addition due to a growing population the treatment and disposition of residual biomass from agricultural processes such as sugar cane and orange bagasse or even from human waste such as sewage sludge will be a challenge for the next generation. These residual biomasses can be an attractive alternative for the production of environmentally friendly fuels and make the economy more circular and efficient. However these raw materials have been hitherto widely used as fuel for boilers or disposed of in sanitary landfills losing their capacity to generate other by-products in addition to contributing to the emissions of gases that promote global warming. For this reason this work analyzes and optimizes the biomass-based routes of biochemical production (namely hydrogen and ammonia) using the gasification of residual biomasses. Moreover the capture of biogenic CO2 aims to reduce the environmental burden leading to negative emissions in the overall energy system. In this context the chemical plants were designed modeled and simulated using Aspen plus™ software. The energy integration and optimization were performed using the OSMOSE Lua Platform. The exergy destruction exergy efficiency and general balance of the CO2 emissions were evaluated. As a result the irreversibility generated by the gasification unit has a relevant influence on the exergy efficiency of the entire plant. On the other hand an overall negative emission balance of −5.95 kgCO2/kgH2 in the hydrogen production route and −1.615 kgCO2/kgNH3 in the ammonia production route can be achieved thus removing from the atmosphere 0.901 tCO2/tbiomass and 1.096 tCO2/tbiomass respectively.
Blue Hydrogen Production from Natural Gas Reservoirs: A Review of Application and Feasibility
Feb 2023
Publication
Recently interest in developing H2 strategies with carbon capture and storage (CCS) technologies has surged. Considering that this paper reviews recent literature on blue H2 a potential low-carbon short-term solution during the H2 transition period. Three key aspects were the focus of this paper. First it presents the processes used for blue H2 production. Second it presents a detailed comparison between blue H2 and natural gas as fuels and energy carriers. The third aspect focuses on CO2 sequestration in depleted natural gas reservoirs an essential step for implementing blue H2. Globally ~ 75% of H2 is produced using steam methane reforming which requires CCS to obtain blue H2. Currently blue H2 needs to compete with other advancing technologies such as green H2 solar power battery storage etc. Compared to natural gas and liquefied natural gas blue H2 gas results in lower CO2 emissions since CCS is applied. However transporting liquefied and compressed blue H2 entails higher energy economic and environmental costs. CCS must be appropriately implemented to produce blue H2 successfully. Due to their established capacity to trap hydrocarbons over geologic time scales depleted natural gas reservoirs are regarded as a viable option for CCS. Such a conclusion is supported by several simulation studies and field projects in many countries. Additionally there is much field experience and knowledge on the injection and production performance of natural gas reservoirs. Therefore using the existing site infrastructure converting these formations into storage reservoirs is undemanding.
Energy Performance Assessment of a Solar-driven Thermochemical Cycle Device for Green Hydrogen Production
Sep 2023
Publication
This paper presents a novel dynamic simulation model for assessing the energy performance of solar-driven systems employed in green hydrogen production. The system consists of a parabolic dish collector that focuses solar radiation on two cerium-based thermochemical reactors. The model is based on a transient finitedifference method to simulate the thermal behaviour of the system and it integrates a theoretical analysis of materials and operating principles. Different empirical data were considered for experimentally validating it: a good agreement between experimental and simulated results was obtained for the temperatures calculated inside the thermochemical reactor (R2 = 0.99 MAPE = 6.3%) and the hourly flow rates of hydrogen oxygen and carbon monoxide (R2 = 0.96 MAPE = 10%) inside the thermochemical reactor. The model was implemented in a MatLab tool for the system dynamic analysis under different boundary conditions. Subsequently to explore the capability of this approach the developed tool was used for analysing the examined device operating in twelve different weather zones. The obtained results comprise heat maps of specific crucial instants and hourly dynamic trends showing redox reaction cycles occurring into the thermochemical reactors. The yearly hydrogen production ranges from 1.19 m3 /y to 1.64 m3 /y according to the hourly incident solar radiations outdoor air temperatures and wind speeds. New graphic tools for rapid feasibility studies are presented. The developed tools and the obtained results can be useful to the basic design of this technology and for the multi-objective optimization of its layout and main design/operating parameters.
Contribution to Net Zero Emissions of Integrating Hydrogen Production in Wastewater Treatment Plants
Jul 2023
Publication
The reliability of renewable hydrogen supply for off-take applications is critical to the future sustainable energy economy. Integrated water electrolysis can be deployed at distributed municipal wastewater treatment plants (WWTP) creating opportunity for reduction in carbon emissions through direct and indirect use of the electrolysis output. A novel energy shifting process where the co-produced oxygen is compressed and stored to enhance the utilisation of intermittent renewable electricity is analysed. The hydrogen produced can be used in local fuel cell electric buses to replace incumbent diesel buses for public transport. However quantifying the extent of carbon emission reduction of this conceptual integrated system is key. In this study the integration of hydrogen production at a case study WWTP of 26000 EP capacity and using the hydrogen in buses was compared with two conventional systems: the base case of a WWTP with grid electricity consumption offset by solar PV and the community’s independent use of diesel buses for transport and the non-integrated configuration with hydrogen produced at the bus refuelling location operated independently of the WWTP. The system response was analysed using a Microsoft Excel simulation model with hourly time steps over a 12-month time frame. The model included a control scheme for the reliable supply of hydrogen for public transport and oxygen to the WWTP and considered expected reductions in carbon intensity of the national grid level of solar PV curtailment electrolyser efficiency and size of the solar PV system. Results showed that by 2031 when Australia’s national electricity is forecast to achieve a carbon intensity of less than 0.186 kg CO2-e/kWh integrating water electrolysis at a municipal WWTP for producing hydrogen for use in local hydrogen buses produced less carbon emissions than continuing to use diesel buses and offsetting emissions by exporting renewable electricity to the grid. By 2034 an annual reduction of 390 t–CO2–e is expected after changing to the integrated configuration. Considering electrolyser efficiency improvements and curtailment of renewable electricity the reduction increases to 872.8 t–CO2–e.
Evaluation of Surplus Hydroelectricity Potential in Nepal until 2040 and its Use for Hydrogen Production Via Electrolysis
May 2023
Publication
The abundant hydro resources in Nepal have resulted in the generation of electricity almost exclusively from hydropower plants. Several hydropower plants are also currently under construction. There is no doubt that the surplus electricity will be significantly high in the coming years. Given the previous trend in electricity consumption it will be a challenge to maximize the use of surplus electricity. In this work the potential solutions to maximize the use of this surplus electricity have been analysed. Three approached are proposed: (i) increasing domestic electricity consumption by shifting the other energy use sectors to electricity (ii) cross-border export of electricity and (iii) conversion of electricity to hydrogen via electrolysis. The current state of energy demand and supply patterns in the country are presented. Future monthly demand forecasts and surplus electricity projections have been made. The hydrogen that can be produced with the surplus electricity via electrolysis is determined and an economic assessment is carried out for the produced hydrogen. The analysis of levelized cost of hydrogen (LCOH) under different scenarios resulted values ranging from 3.8 €/kg to 4.5 €/kg.
Is the Polish Solar-to-Hydrogen Pathway Green? A Carbon Footprint of AEM Electrolysis Hydrogen Based on an LCA
Apr 2023
Publication
Efforts to direct the economies of many countries towards low-carbon economies are being made in order to reduce their impact on global climate change. Within this process replacing fossil fuels with hydrogen will play an important role in the sectors where electrification is difficult or technically and economically ineffective. Hydrogen may also play a critical role in renewable energy storage processes. Thus the global hydrogen demand is expected to rise more than five times by 2050 while in the European Union a seven-fold rise in this field is expected. Apart from many technical and legislative barriers the environmental impact of hydrogen production is a key issue especially in the case of new and developing technologies. Focusing on the various pathways of hydrogen production the essential problem is to evaluate the related emissions through GHG accounting considering the life cycle of a plant in order to compare the technologies effectively. Anion exchange membrane (AEM) electrolysis is one of the newest technologies in this field with no LCA studies covering its full operation. Thus this study is focused on a calculation of the carbon footprint and economic indicators of a green hydrogen plant on the basis of a life cycle assessment including the concept of a solar-to-hydrogen plant with AEM electrolyzers operating under Polish climate conditions. The authors set the range of the GWP indicators as 2.73–4.34 kgCO2eq for a plant using AEM electrolysis which confirmed the relatively low emissivity of hydrogen from solar energy also in relation to this innovative technology. The economic profitability of the investment depends on external subsidies because as developing technology the AEM electrolysis of green hydrogen from photovoltaics is still uncompetitive in terms of its cost without this type of support.
Decommissioning Platforms to Offshore Solar System: Road to Green Hydrogen Production from Seawater
May 2023
Publication
With more than 140 offshore platforms identified in Malaysian water to be decommissioned within 10 years it is critical for the Oil and Gas operators to re-evaluate the overall decommissioning strategies for a more sustainable approach. A revision to the current decommissioning options with inclusion of green decommissioning plan to the overall decision tree will assist in accelerating sustainable decision making. Using the advantage of the available 3D modelling from Naviswork and convert to PVSyst software for solar analysis to the one of the shortlisted offshore gas complexes in Malaysia three solar powered generation scenario was evaluated with aimed to establish the best integrated system on a modified decommissioned unmanned processing platform to generate cleaner energy. Financial assessment inclusive of Levelized Cost of Electricity as well as environmental assessment for each scenario are evaluated together. From the study optimum tilt angle was determined resulted to best annual solar yield of 257MWh with performance ratio (PR) of 87% for on-grid scenario 1. Off-grid scenario 3 is used to understand the estimated green hydrogen production. A desktop investigation conducted to three (3) type of electrolysers resulted to 8.6 kg to 18 kg of green hydrogen based on the average daily solar yield produced in scenario 3. Using Proton Electron Membrane electrolyser to simulate the PV solar-to-hydrogen offshore system it is observed that 98% of annual solar fraction can be achieved with annual performance ratio of 74.5% with levelized cost of Hydrogen (LCOH) of $10.95 per kg. From financial assessment this study justifies platforms repurpose to renewable energy concept to be an attractive option since cost to decommission the identified complex was observed to be 11 times greater compared to investing for this proposed concept.
System-friendly Process Design: Optimizing Blue Hydrogen Production for Future Energy Systems
Aug 2022
Publication
While the effects of ongoing cost reductions in renewables batteries and electrolyzers on future energy systems have been extensively investigated the effects of significant advances in CO2 capture and storage (CCS) technologies have received much less attention. This research gap is addressed via a long-term (2050) energy system model loosely based on Germany yielding four main findings. First CCS-enabled pathways offer the greatest benefits in the hydrogen sector where hydrogen prices can be reduced by two-thirds relative to a scenario without CCS. Second advanced blue hydrogen technologies can reduce total system costs by 12% and enable negative CO2 emissions due to higher efficiencies and CO2 capture ratios. Third co-gasification of coal and biomass emerged as an important enabler of these promising results allowing efficient exploitation of limited biomass resources to achieve negative emissions and limit the dependence on imported natural gas. Finally CCS decarbonization pathways can practically and economically incorporate substantial shares of renewable energy to reduce fossil fuel dependence. Such diversification of primary energy inputs increases system resilience to the broad range of socio-techno-economic challenges facing the energy transition. In conclusion balanced blue-green pathways offer many benefits and deserve serious consideration in the global decarbonization effort.
Simulation and Techno-Economic Assessment of Hydrogen Production from Biomass Gasification-Based Processes: A Review
Nov 2022
Publication
The development of low-carbon fuels from renewable resources is a key measure to reduce carbon dioxide emissions and mitigate climate change. Biomass gasification with subsequent gas processing and purification is a promising route to produce low-carbon hydrogen. In the past decade simulation-based modelling using Aspen Plus software has supported the investigation of future potential industrial applications of this pathway. This article aims to provide a review of the modelling and economic assessment of woody biomass gasification-based hydrogen production with focus on the evaluation of the model accuracy in predicting producer gas composition in comparison with experimental data depending on the approach implemented. The assessment of comprehensive models which integrate biomass gasification with gas processing and purification highlights how downstream gas processing could improve the quality of the syngas and thus the hydrogen yield. The information in this article provides an overview of the current practices challenges and opportunities for future research particularly for the development of a comprehensive pathway for hydrogen production based on biomass gasification. Moreover this review includes a techno-economic assessment of biomass to hydrogen processes which will be useful for implementation at industrial-scale.
Techno-economic Analysis to Identify the Optimal Conditions for Green Hydrogen Production
Jun 2023
Publication
The intermittency of renewable energy sources necessitates energy storage to meet the full demand and balancing requirements of the grid. Green hydrogen (H2) is a chemical energy carrier that can be used in a flexible manner and store large amounts of energy for long periods of time. This techno-economic analysis investigates H2 production from wind using commercially available desalination and electrolysis units. Proton exchange membrane and alkaline electrolyser units are utilised and compared. The intermittency of wind is examined with comparison against grid-bought electricity. A model is developed to determine the selling price required to ensure profitability over a 10-year period. Firstly where H2 is produced using energy from the grid with electricity purchased when below a specified price point or between specified hours. In the second scenario a wind turbine is owned by the user and the electricity price is not considered while the turbine capital expenditure is. The price of H2 production from wind is found to be comparable with natural gas derived H2 at a larger scale with a minimum selling price calculated to be 4.85 £/kg at a setpoint of 500 kg of H2/hr. At a setpoint of 50 kg of H2/hr this is significantly higher at 12.10 £/kg. In both cases the alkaline electrolyser produced cheaper H2. This study demonstrates an economy of scale with H2 prices decreasing with increased scale. H2 prices are also closely linked to the capital expenditure with the equipment size space and safety identified as limiting factors.
Optimal Renewable Energy Distribution Between Gasifier and Electrolyzer for Syngas Generation in a Power and Biomass-to-Liquid Fuel Process
Jan 2022
Publication
By adding energy as hydrogen to the biomass-to-liquid (BtL) process several published studies have shown that carbon efficiency can be increased substantially. Hydrogen can be produced from renewable electrical energy through the electrolysis of water or steam. Adding high-temperature thermal energy to the gasifier will also increase the overall carbon efficiency. Here an economic criterion is applied to find the optimal distribution of adding electrical energy directly to the gasifier as opposed to the electrolysis unit. Three different technologies for electrolysis are applied: solid oxide steam electrolysis (SOEC) alkaline water electrolysis (AEL) and proton exchange membrane (PEM). It is shown that the addition of part of the renewable energy to the gasifier using electric heaters is always beneficial and that the electrolysis unit operating costs are a significant portion of the costs. With renewable electricity supplied at a cost of 50 USD/MWh and a capital cost of 1500 USD/kW installed SOEC the operating costs of electric heaters and SOEC account for more than 70% of the total costs. The energy efficiency of the electrolyzer is found to be more important than the capital cost. The optimal amount of energy added to the gasifier is about 37–39% of the energy in the biomass feed. A BtL process using renewable hydrogen imports at 2.5 USD/kg H2 or SOEC for hydrogen production at reduced electricity prices gives the best values for the economic objective.
Grid-supported Electrolytic Hydrogen Production: Cost of Climate Impact Using Dynamic Emission Factors
Aug 2023
Publication
Hydrogen production based on a combination of intermittent renewables and grid electricity is a promising approach for reducing emissions in hard-to-decarbonise sectors at lower costs. However for such a configuration to provide climate benefits it is crucial to ensure that the grid electricity consumed in the process is derived from low-carbon sources. This paper examined the use of hourly grid emission factors (EFs) to more accurately determine the short-term climate impact of dynamically operated electrolysers. A model of the interconnected northern European electricity system was developed and used to calculate average grid-mix and marginal EFs for the four bidding zones in Sweden. Operating a 10 MW electrolyser using a combination of onshore wind and grid electricity was found to decrease the levelised cost of hydrogen (LCOH) to 2.40–3.63 €/kgH2 compared with 4.68 €/kgH2 for wind-only operation. A trade-off between LCOH and short-term climate impact was revealed as specific marginal emissions could exceed 20 kgCO2eq/kgH2 at minimum LCOH. Both an emission-minimising operating strategy and an increased wind-to-electrolyser ratio was found to manage this trade-off by enabling simultaneous cost and emission reductions lowering the marginal carbon abatement cost (CAC) from 276.8 €/tCO2eq for wind-only operation to a minimum of 222.7 and 119.3 €/tCO2eq respectively. Both EF and LCOH variations were also identified between the bidding zones but with no notable impact on the marginal CAC. When using average grid-mix emission factors the climate impact was low and the CAC could be reduced to 71.3–200.0 €/tCO2eq. In relation to proposed EU policy it was demonstrated that abiding by hourly renewable temporal matching principles could ensure low marginal emissions at current levels of fossil fuels in the electricity mix.
Thermal Design of a Biohydrogen Production System Driven by Integrated Gasification Combined Cycle Waste Heat Using Dynamic Simulation
Apr 2022
Publication
Utilizing biological processes for hydrogen production via gasification is a promising alternative method to coal gasification. The present study proposes a dynamic simulation model that uses a one-dimensional heat-transfer analysis method to simulate a biohydrogen production system. The proposed model is based on an existing experimental design setup. It is used to simulate a biohydrogen production system driven by the waste heat from an integrated gasification combined cycle (IGCC) power plant equipped with carbon capture and storage technologies. The data from the simulated results are compared with the experimental measurement data to validate the developed model’s reliability. The results show good agreement between the experimental data and the developed model. The relative root-mean-square error for the heat storage feed-mixing and bioreactor tanks is 1.26% 3.59% and 1.78% respectively. After the developed model’s reliability is confirmed it is used to simulate and optimize the biohydrogen production system inside the IGCC power plant. The bioreactor tank’s time constant can be improved when reducing the operating volume of the feed-mixing tank by the scale factors of 0.75 and 0.50 leading to a 15.76% and 31.54% faster time constant respectively when compared with the existing design.
Minimizing the Cost of Hydrogen Production through Dynamic Polymer Electrolyte Membrane Electrolyzer Operation
Jun 2022
Publication
Growing imbalances between electricity demand and supply from variable renewable energy sources (VREs) create increasingly large swings in electricity prices. Polymer electrolyte membrane (PEM) electrolyzers can help to buffer against these imbalances and minimize the levelized cost of hydrogen (LCOH) by ramping up production of hydrogen through high-current-density operation when low-cost electricity is abundant and ramping down current density to operate efficiently when electricity prices are high. We introduce a technoeconomic model that optimizes current density profiles for dynamically operated electrolyzers while accounting for the potential of increased degradation rates to minimize LCOH for any given time-of-use (TOU) electricity pricing. This model is used to predict LCOH from different methods of operating a PEM electrolyzer for historical and projected electricity prices in California and Texas which were chosen due to their high penetration of VREs. Results reveal that dynamic operation could enable reductions in LCOH ranging from 2% to 63% for historical 2020 pricing and 1% to 53% for projected 2030 pricing. Moreover high-current-density operation above 2.5 A cm2 is increasingly justified at electricity prices below $0.03 kWh1 . These findings suggest an actionable means of lowering LCOH and guide PEM electrolyzer development toward devices that can operate efficiently at a range of current densities.
Review—Identifying Critical Gaps for Polymer Electrolyte Water Electrolysis Development
Feb 2017
Publication
Although polymer electrolyte water electrolyzers (PEWEs) have been used in small-scale (kW to tens of kW range) applications for several decades PEWE technology for hydrogen production in energy applications (power-to-gas power-to-fuel etc.) requires significant improvements in the technology to address the challenges associated with cost performance and durability. Systems with power of hundreds of kW or even MWs corresponding to hydrogen production rates of around 10 to 20 kg/h have started to appear in the past 5 years. The thin (∼0.2 mm) polymer electrolyte in the PEWE with low ohmic resistance compared to the alkaline cell with liquid electrolyte allows operation at high current densities of 1–3 A/cm2 and high differential pressure. This article after an introductory overview of the operating principles of PEWE and state-of-the-art discusses the state of understanding of key phenomena determining and limiting performance durability and commercial readiness identifies important ‘gaps’ in understanding and essential development needs to bring PEWE science & engineering forward to prosper in the energy market as one of its future backbone technologies. For this to be successful science engineering and process development as well as business and market development need to go hand in hand.
Renewable Hydrogen Production Processes for the Off-Gas Valorization in Integrated Steelworks through Hydrogen Intensified Methane and Methanol Syntheses
Nov 2020
Publication
Within integrated steelmaking industries significant research efforts are devoted to the efficient use of resources and the reduction of CO2 emissions. Integrated steelworks consume a considerable quantity of raw materials and produce a high amount of by-products such as off-gases currently used for the internal production of heat steam or electricity. These off-gases can be further valorized as feedstock for methane and methanol syntheses but their hydrogen content is often inadequate to reach high conversions in synthesis processes. The addition of hydrogen is fundamental and a suitable hydrogen production process must be selected to obtain advantages in process economy and sustainability. This paper presents a comparative analysis of different hydrogen production processes from renewable energy namely polymer electrolyte membrane electrolysis solid oxide electrolyze cell electrolysis and biomass gasification. Aspen Plus® V11-based models were developed and simulations were conducted for sensitivity analyses to acquire useful information related to the process behavior. Advantages and disadvantages for each considered process were highlighted. In addition the integration of the analyzed hydrogen production methods with methane and methanol syntheses is analyzed through further Aspen Plus®-based simulations. The pros and cons of the different hydrogen production options coupled with methane and methanol syntheses included in steelmaking industries are analyzed
Premier, Progress and Prospects in Renewable Hydrogen Generation: A Review
May 2023
Publication
Renewable hydrogen production has an opportunity to reduce carbon emissions in the transportation and industrial sectors. This method generates hydrogen utilizing renewable energy sources such as the sun wind and hydropower lowering the number of greenhouse gases released into the environment. In recent years considerable progress has been made in the production of sustainable hydrogen particularly in the disciplines of electrolysis biomass gasification and photoelectrochemical water splitting. This review article figures out the capacity efficiency and cost-effectiveness of hydrogen production from renewable sources effectively comparing the conventionally used technologies with the latest techniques which are getting better day by day with the implementation of the technological advancements. Governments investors and industry players are increasingly interested in manufacturing renewable hydrogen and the global need for clean energy is expanding. It is projected that facilities for manufacturing renewable hydrogen as well as infrastructure to support this development would expand hastening the transition to an environment-friendly and low-carbon economy
Hydrogen Role in the Valorization of Integrated Steelworks Process Off-gases through Methane and Methanol Syntheses
Jun 2021
Publication
The valorization of integrated steelworks process off-gases as feedstock for synthesizing methane and methanol is in line with European Green Deal challenges. However this target can be generally achieved only through process off-gases enrichment with hydrogen and use of cutting-edge syntheses reactors coupled to advanced control systems. These aspects are addressed in the RFCS project i3 upgrade and the central role of hydrogen was evident from the first stages of the project. First stationary scenario analyses showed that the required hydrogen amount is significant and existing renewable hydrogen production technologies are not ready to satisfy the demand in an economic perspective. The poor availability of low-cost green hydrogen as one of the main barriers for producing methane and methanol from process off-gases is further highlighted in the application of an ad-hoc developed dispatch controller for managing hydrogen intensified syntheses in integrated steelworks. The dispatch controller considers both economic and environmental impacts in the cost function and although significant environmental benefits are obtainable by exploiting process off-gases in the syntheses the current hydrogen costs highly affect the dispatch controller decisions. This underlines the need for big scale green hydrogen production processes and dedicated green markets for hydrogen-intensive industries which would ensure easy access to this fundamental gas paving the way for a C-lean and more sustainable steel production.
Assessing Sizing Optimality of OFF-GRID AC-Linked Solar PV-PEM Systems for Hydrogen Production
Jul 2023
Publication
Herein a novel methodology to perform optimal sizing of AC-linked solar PV-PEM systems is proposed. The novelty of this work is the proposition of the solar plant to electrolyzer capacity ratio (AC/AC ratio) as optimization variable. The impact of this AC/AC ratio on the Levelized Cost of Hydrogen (LCOH) and the deviation of the solar DC/AC ratio when optimized specifically for hydrogen production are quantified. Case studies covering a Global Horizontal Irradiation (GHI) range of 1400e2600 kWh/m2 -year are assessed. The obtained LCOHs range between 5.9 and 11.3 USD/kgH2 depending on sizing and location. The AC/AC ratio is found to strongly affect cost production and LCOH optimality while the optimal solar DC/AC ratio varies up to 54% when optimized to minimize the cost of hydrogen instead of the cost of energy only. Larger oversizing is required for low GHI locations; however H2 production is more sensitive to sizing ratios for high GHI locations.
Sustainable Ammonia Production Processes
Mar 2021
Publication
Due to the important role of ammonia as a fertilizer in the agricultural industry and its promising prospects as an energy carrier many studies have recently attempted to find the most environmentally benign energy efficient and economically viable production process for ammonia synthesis. The most commonly utilized ammonia production method is the Haber-Bosch process. The downside to this technology is the high greenhouse gas emissions surpassing 2.16 kgCO2-eq/kg NH3 and high amounts of energy usage of over 30 GJ/tonne NH3 mainly due to the strict operational conditions at high temperature and pressure. The most widely adopted technology for sustainable hydrogen production used for ammonia synthesis is water electrolysis coupled with renewable technologies such as wind and solar. In general a water electrolyzer requires a continuous supply of pretreated water with high purity levels for its operation. Moreover for production of 1 tonne of hydrogen 9 tonnes of water is required. Based on this data for the production of the same amount of ammonia through water electrolysis 233.6 million tonnes/yr of water is required. In this paper a critical review of different sustainable hydrogen production processes and emerging technologies for sustainable ammonia synthesis along with a comparative life cycle assessment of various ammonia production methods has been carried out. We find that through the review of each of the studied technologies either large amounts of GHG emissions are produced or high volumes of pretreated water is required or a combination of both these factors occur.
Design Strategies for Large Current Density Hydrogen Evolution Reaction
Apr 2022
Publication
Hydrogen energy is considered one of the cleanest and most promising alternatives to fossil fuel because the only combustion product is water. The development of water splitting electrocatalysts with Earth abundance cost-efficiency and high performance for large current density industrial applications is vital for H2 production. However most of the reported catalysts are usually tested within relatively small current densities (< 100 mA cm−2 ) which is far from satisfactory for industrial applications. In this minireview we summarize the latest progress of effective non-noble electrocatalysts for large current density hydrogen evolution reaction (HER) whose performance is comparable to that of noble metal-based catalysts. Then the design strategy of intrinsic activities and architecture design are discussed including self-supporting electrodes to avoid the detachment of active materials the superaerophobicity and superhydrophilicity to release H2 bubble in time and the mechanical properties to resist destructive stress. Finally some views on the further development of high current density HER electrocatalysts are proposed such as scale up of the synthesis process in situ characterization to reveal the micro mechanism and the implementation of catalysts into practical electrolyzers for the commercial application of as-developed catalysts. This review aimed to guide HER catalyst design and make large-scale hydrogen production one step further.
Aluminum-Based Fuels as Energy Carriers for Controllable Power and Hydrogen Generation—A Review
Dec 2022
Publication
Metallic aluminum is widely used in propellants energy-containing materials and batteries due to its high energy density. In addition to burning in the air aluminum can react with water to generate hydrogen. Aluminum is carbon-free and the solid-phase products can be recycled easily after the reaction. Micron aluminum powder is stable in the air and enables global trade. Aluminum metal is considered to be a viable recyclable carrier for clean energy. Based on the reaction characteristics of aluminum fuel in air and water this work summarizes the energy conversion system of aluminum fuel the combustion characteristics of aluminum and the recycling of aluminum. The conversion path and application direction of electric energy and chemistry in the aluminum energy conversion system are described. The reaction properties of aluminum in the air are described as well as the mode of activation and the effects of the aluminum-water reaction. In situ hydrogen production is achievable through the aluminum-water reaction. The development of low-carbon and energy-saving electrolytic aluminum technology is introduced. The work also analyzes the current difficulties and development directions for the large-scale application of aluminum fuel energy storage technology. The development of energy storage technology based on aluminum is conducive to transforming the energy structure.
Energy Sustainability Analysis (ESA) of Energy-Producing Processes: A Case Study on Distributed H2 Production
Sep 2019
Publication
In the sustainability context the performance of energy-producing technologies using different energy sources needs to be scored and compared. The selective criterion of a higher level of useful energy to feed an ever-increasing demand of energy to satisfy a wide range of endo- and exosomatic human needs seems adequate. In fact surplus energy is able to cover energy services only after compensating for the energy expenses incurred to build and to run the technology itself. This paper proposes an energy sustainability analysis (ESA) methodology based on the internal and external energy use of a given technology considering the entire energy trajectory from energy sources to useful energy. ESA analysis is conducted at two levels: (i) short-term by the use of the energy sustainability index (ESI) which is the first step to establish whether the energy produced is able to cover the direct energy expenses needed to run the technology and (ii) long-term by which all the indirect energy-quotas are considered i.e. all the additional energy requirements of the technology including the energy amortization quota necessary for the replacement of the technology at the end of its operative life. The long-term level of analysis is conducted by the evaluation of two indicators: the energy return per unit of energy invested (EROI) over the operative life and the energy payback-time (EPT) as the minimum lapse at which all energy expenditures for the production of materials and their construction can be repaid to society. The ESA methodology has been applied to the case study of H2 production at small-scale (10–15 kWH2) comparing three different technologies: (i) steam-methane reforming (SMR) (ii) solar-powered water electrolysis (SPWE) and (iii) two-stage anaerobic digestion (TSAD) in order to score the technologies from an energy sustainability perspective.
Up-to-Date Status of Geoscience in the Field of Natural Hydrogen with Consideration of Petroleum Issues
Sep 2023
Publication
The perspective of natural hydrogen as a clear carbon-free and renewable energy source appears very promising. There have been many studies reporting significant concentrations of natural hydrogen in different countries. However natural hydrogen is being extracted to generate electricity only in Mali. This issue originates from the fact that global attention has not been dedicated yet to the progression and promotion of the natural hydrogen field. Therefore being in the beginning stage natural hydrogen science needs further investigation especially in exploration techniques and exploitation technologies. The main incentive of this work is to analyze the latest advances and challenges pertinent to the natural hydrogen industry. The focus is on elaborating geological origins ground exposure types extraction techniques previous detections of natural hydrogen exploration methods and underground hydrogen storage (UHS). Thus the research strives to shed light on the current status of the natural hydrogen field chiefly from the geoscience perspective. The data collated in this review can be used as a useful reference for the scientists engineers and policymakers involved in this emerging renewable energy source.
Electrochemical Ammonia: Power to Ammonia Ratio and Balance of Plant Requirements for Two Different Electrolysis Approaches
Nov 2021
Publication
Electrochemical ammonia generation allows direct low pressure synthesis of ammonia as an alternative to the established Haber-Bosch process. The increasing need to drive industry with renewable electricity central to decarbonisation and electrochemical ammonia synthesis offers a possible efficient and low emission route for this increasingly important chemical. It also provides a potential route for more distributed and small-scale ammonia synthesis with a reduced production footprint. Electrochemical ammonia synthesis is still early stage but has seen recent acceleration in fundamental understanding. In this work two different ammonia electrolysis systems are considered. Balance of plant (BOP) requirements are presented and modelled to compare performance and determine trade-offs. The first option (water fed cell) uses direct ammonia synthesis from water and air. The second (hydrogen-fed cell) involves a two-step electrolysis approach firstly producing hydrogen followed by electrochemical ammonia generation. Results indicate that the water fed approach shows the most promise in achieving low energy demand for direct electrochemical ammonia generation. Breaking the reaction into two steps for the hydrogen fed approach introduces a source of inefficiency which is not overcome by reduced BOP energy demands and will only be an attractive pathway for reactors which promise both high efficiency and increased ammonia formation rate compared to water fed cells. The most optimised scenario investigated here with 90% faradaic efficiency (FE) and 1.5 V cell potential (75% nitrogen utilisation) gives a power to ammonia value of 15 kWh/kg NH3 for a water fed cell. For the best hydrogen fed arrangement the requirement is 19 kWh/kg NH3. This is achieved with 0.5 V cell potential and 75% utilisation of both hydrogen and nitrogen (90% FE). Modelling demonstrated that balance of plant requirements for electrochemical ammonia are significant. Electrochemical energy inputs dominate energy requirements at low FE however in cases of high FE the BOP accounts for approximately 50% of the total energy demand mostly from ammonia separation requirements. In the hydrogen fed cell arrangement it was also demonstrated that recycle of unconverted hydrogen is essential for efficient operation even in the case where this increases BOP energy inputs
Exploring the Possibility of Using Molten Carbonate Fuel Cell for the Flexible Coproduction of Hydrogen and Power
Sep 2021
Publication
Fuel cells are electrochemical devices that are conventionally used to convert the chemical energy of fuels into electricity while producing heat as a byproduct. High temperature fuel cells such as molten carbonate fuel cells and solid oxide fuel cells produce significant amounts of heat that can be used for internal reforming of fuels such as natural gas to produce gas mixtures which are rich in hydrogen while also producing electricity. This opens up the possibility of using high temperature fuel cells in systems designed for flexible coproduction of hydrogen and power at very high system efficiency. In a previous study the flowsheet software Cycle-Tempo has been used to determine the technical feasibility of a solid oxide fuel cell system for flexible coproduction of hydrogen and power by running the system at different fuel utilization factors (between 60 and 95%). Lower utilization factors correspond to higher hydrogen production while at a higher fuel utilization standard fuel cell operation is achieved. This study uses the same basis to investigate how a system with molten carbonate fuel cells performs in identical conditions also using Cycle-Tempo. A comparison is made with the results from the solid oxide fuel cell study.
Assessment of Greenhouse Gas Emissions from Hydrogen Production Processes: Turquoise Hydrogen vs. Steam Methane Reforming
Nov 2022
Publication
Hydrogen has received substantial attention because of its diverse application in the energy sector. Steam methane reforming (SMR) dominates the current hydrogen production and is the least expensive endothermic reaction to produce grey hydrogen. This technology provides the advantages of low cost and high energy efficiency; however it emits an enormous amount of CO2. Carbon capture storage (CCS) technology helps reduce these emissions by 47% to 53% producing blue hydrogen. Methane pyrolysis is an alternative to SMR that produces (ideally) CO2-free turquoise hydrogen. In practice methane pyrolysis reduces CO2 emissions by 71% compared to grey hydrogen and 46% compared to blue hydrogen. While carbon dioxide emissions decrease with CCS fugitive methane emissions (FMEs) for blue and turquoise hydrogen are higher than those for grey hydrogen because of the increased use of natural gas to power carbon capture. We undertake FMEs of 3.6% of natural gas consumption for individual processes. In this study we also explore the utilization of biogas as a feedstock and additional Boudouard reactions for efficient utilization of solid carbon from methane pyrolysis and carbon dioxide from biogas. The present study focuses on possible ways to reduce overall emissions from turquoise hydrogen to provide solutions for a sustainable low-CO2 energy source.
Additive Manufacturing for Proton Exchange Membrane (PEM) Hydrogen Technologies: Merits, Challenges, and Prospects
Jul 2023
Publication
With the growing demand for green technologies hydrogen energy devices such as Proton Exchange Membrane (PEM) fuel cells and water electrolysers have received accelerated developments. However the materials and manufacturing cost of these technologies are still relatively expensive which impedes their widespread commercialization. Additive Manufacturing (AM) commonly termed 3D Printing (3DP) with its advanced capabilities could be a potential pathway to solve the fabrication challenges of PEM parts. Herein in this paper the research studies on the novel AM fabrication methods of PEM components are thoroughly reviewed and analysed. The key performance properties such as corrosion and hydrogen embrittlement resistance of the additively manufactured materials in the PEM working environment are discussed to emphasise their reliability for the PEM systems. Additionally the major challenges and required future developments of AM technologies to unlock their full potential for PEM fabrication are identified. This paper provides insights from the latest research developments on the significance of advanced manufacturing technologies in developing sustainable energy systems to address the global energy challenges and climate change effects.
A Review of Recent Advances in Water-gas Shift Catalysis for Hydrogen Production
Aug 2020
Publication
The water-gas shift reaction (WGSR) is an intermediate reaction in hydrocarbon reforming processes considered one of the most important reactions for hydrogen production. Here water and carbon monoxide molecules react to generate hydrogen and carbon dioxide. From the thermodynamics aspect pressure does not have an impact whereas low-temperature conditions are suitable for high hydrogen selectivity because of the exothermic nature of the WGSR reaction. The performance of this reaction can be greatly enhanced in the presence of suitable catalysts. The WGSR has been widely studied due do the industrial significance resulting in a good volume of open literature on reactor design and catalyst development. A number of review articles are also available on the fundamental aspects of the reaction including thermodynamic analysis reaction condition optimization catalyst design and deactivation studies. Over the past few decades there has been an exceptional development of the catalyst characterization techniques such as near-ambient x-ray photoelectron spectroscopy (NA-XPS) and in situ transmission electron microscopy (in situ TEM) providing atomic level information in presence of gases at elevated temperatures. These tools have been crucial in providing nanoscale structural details and the dynamic changes during reaction conditions which were not available before. The present review is an attempt to gather the recent progress particularly in the past decade on the catalysts for low-temperature WGSR and their structural properties leading to new insights that can be used in the future for effective catalyst design. For the ease of reading the article is divided into subsections based on metals (noble and transition metal) oxide supports and carbon-based supports. It also aims at providing a brief overview of the reaction conditions by including a table of catalysts with synthesis methods reaction conditions and key observations for a quick reference. Based on our study of literature on noble metal catalysts atomic Pt substituted Mn3O4 shows almost full CO conversion at 260 °C itself with zero methane formation. In the case of transition metals group the inclusion of Cu in catalytic system seems to influence the CO conversion significantly and in some cases with CO conversion improvement by 65% at 280 °C. Moreover mesoporous ceria as a catalyst support shows great potential with reports of full CO conversion at a low temperature of 175 °C.
Hydrogen Environmental Benefits Depend on the Way of Production: An Overview of the Main Processes Production and Challenges by 2050
Jun 2021
Publication
Hydrogen (H2) is presented as an important alternative for clean energy and raw material in the modern world. However the environmental benefits are linked to its process of production. Herein the chemical aspects advantages/disadvantages and challenges of the main processes of H2 production from petroleum to water are described. The fossil fuel (FF)-based methods and the state-of-art strategies are outlined to produce hydrogen from water (electrolysis) wastewater and seawater. In addition a discussion based on a color code to classify the cleanliness of hydrogen production is introduced. By the end a summary of the hydrogen value chain addresses topics related to the financial aspects and perspective for 2050: green hydrogen and zero-emission carbon.
Methane Pyrolysis in a Liquid Metal Bubble Column Reactor for CO2-Free Production of Hydrogen
Oct 2023
Publication
In light of the growing interest in hydrogen as an energy carrier and reducing agent various industries including the iron and steel sector are considering the increased adoption of hydrogen. To meet the rising demand in energy-intensive industries the production of hydrogen must be significantly expanded and further developed. However current hydrogen production heavily relies on fossil-fuel-based methods resulting in a considerable environmental burden with approximately 10 tons of CO2 emissions per ton of hydrogen. To address this challenge methane pyrolysis offers a promising approach for producing clean hydrogen with reduced CO2 emissions. This process involves converting methane (CH4 ) into hydrogen and solid carbon significantly lowering the carbon footprint. This work aims to enhance and broaden the understanding of methane pyrolysis in a liquid metal bubble column reactor (LMBCR) by utilizing an expanded and improved experimental setup based on the reactor concept previously proposed by authors from Montanuniversitaet in 2022 and 2023. The focus is on investigating the process parameters’ temperature and methane input rate with regard to their impact on methane conversion. The liquid metal temperature exhibits a strong influence increasing methane conversion from 35% at 1150 ◦C to 74% at 1250 ◦C. In contrast the effect of the methane flow rate remains relatively small in the investigated range. Moreover an investigation is conducted to assess the impact of carbon layers covering the surface of the liquid metal column. Additionally a comparative analysis between the LMBCR and a blank tube reactor (BTR) is presented.
Opportunities for Flexible Electricity Loads such as Hydrogen Production from Curtailed Generation
Jun 2021
Publication
Variable low-cost low-carbon electricity that would otherwise be curtailed may provide a substantial economic opportunity for entities that can flexibly adapt their electricity consumption. We used historical hourly weather data over the contiguous U.S. to model the characteristics of least-cost electricity systems dominated by variable renewable generation that powered firm and flexible electricity demands (loads). Scenarios evaluated included variable wind and solar power battery storage and dispatchable natural gas with carbon capture and storage with electrolytic hydrogen representing a prototypical flexible load. When flexible loads were small excess generation capacity was available during most hours allowing flexible loads to operate at high capacity factors. Expanding the flexible loads allowed the least-cost systems to more fully utilize the generation capacity built to supply firm loads and thus reduced the average cost of delivered electricity. The macro-scale energy model indicated that variable renewable electricity systems optimized to supply firm loads at current costs could supply 25% or more additional flexible load with minimal capacity expansion while resulting in reduced average electricity costs (10% or less capacity expansion and 10% to 20% reduction in costs in our modeled scenarios). These results indicate that adding flexible loads to electricity systems will likely allow more full utilization of generation assets across a wide range of system architectures thus providing new energy services with infrastructure that is already needed to supply firm electricity loads.
An Insight into Carbon Nanomaterial-Based Photocatalytic Water Splitting for Green Hydrogen Production
Dec 2022
Publication
At present the energy shortage and environmental pollution are the burning global issues. For centuries fossil fuels have been used to meet worldwide energy demand. However thousands of tons of greenhouse gases are released into the atmosphere when fossil fuels are burned contributing to global warming. Therefore green energy must replace fossil fuels and hydrogen is a prime choice. Photocatalytic water splitting (PWS) under solar irradiation could address energy and environmental problems. In the past decade solar photocatalysts have been used to manufacture sustainable fuels. Scientists are working to synthesize a reliable affordable and light-efficient photocatalyst. Developing efficient photocatalysts for water redox reactions in suspension is a key to solar energy conversion. Semiconductor nanoparticles can be used as photocatalysts to accelerate redox reactions to generate chemical fuel or electricity. Carbon materials are substantial photocatalysts for total WS under solar irradiation due to their high activity high stability low cost easy production and structural diversity. Carbon-based materials such as graphene graphene oxide graphitic carbon nitride fullerenes carbon nanotubes and carbon quantum dots can be used as semiconductors photosensitizers cocatalysts and support materials. This review comprehensively explains how carbon-based composite materials function as photocatalytic semiconductors for hydrogen production the water-splitting mechanism and the chemistry of redox reactions. Also how heteroatom doping defects and surface functionalities etc. can influence the efficiency of carbon photocatalysts in H2 production. The challenges faced in the PWS process and future prospects are briefly discussed.
Review and Meta-analysis of Recent Life Cycle Assessments of Hydrogen Production
Apr 2023
Publication
The world is facing an urgent global climate challenge and hydrogen (H2) is increasingly valued as a carbon-free energy carrier that can play a prominent role in decarbonising economies. However the environmental impact of the different methods for hydrogen production are sometimes overlooked. This work provides a comprehensive overview of the environmental impacts and costs of a diverse range of methods for producing hydrogen. Ninety nine life cycle assessments (LCAs) of hydrogen production published between 2015 and 2022 are categorised by geography production method energy source goal and scope and compared by data sources and methodology. A meta-analysis of methodological choices is used to identify a subset of mutually comparable studies whose results are then compared initially by global warming potential (GWP) then low-GWP scenarios are compared by other indicators. The results show that the lowest GWP is achieved by methods that are currently more expensive (~US $4–9/kg H2) compared to the dominant methods of producing hydrogen from fossil fuels (~US $1–2/kg H2). The research finds that data are currently limited for comparing environmental indicators other than GWP such as terrestrial acidification or freshwater eutrophication. Recommendations are made for future LCAs of hydrogen production.
Economic Assessment of Clean Hydrogen Production from Fossil Fuels in the Intermountain-west Region, USA
Jan 2024
Publication
The transition from fossil fuels to carbon-neutral energy sources is necessary to reduce greenhouse gas (GHG) emissions and combat climate change. Hydrogen (H2) provides a promising path to harness fossil fuels to reduce emissions in sectors such as transportation. However regional economic analyses of various H2 production techniques are still lacking. We selected a well-known fossil fuel-exporting region the USA’s Intermountain-West (I-WEST) to analyze the carbon intensity of H2 production and demonstrate regional tradeoffs. Currently 78 % of global H2 production comes from natural gas and coal. Therefore we considered steam methane reforming (SMR) surface coal gasification (SCG) and underground coal gasification (UCG) as H2 production methods in this work. We developed the cost estimation frameworks of SMR SCG and UCG with and without carbon capture utilization and sequestration (CCUS). In addition we identified optimal sites for H2 hubs by considering the proximity to energy sources energy markets storage sites and CO2 sequestration sites. We included new production tax credits (PTCs) in the cost estimation to quantify the economic benefit of CCUS. Our results suggest that the UCG has the lowest levelized cost of H2 production due to the elimination of coal production cost. H2 production using the SMR process with 99 % carbon capture is profitable when the PTCs are considered. We also analyzed carbon utilization opportunities where CO2 conversion to formic acid is a promising profitable option. This work quantifies the potential of H2 production from fossil fuels in the I-WEST region a key parameter for designing energy transition pathways.
Recent Advances in High-Temperature Steam Electrolysis with Solid Oxide Electrolysers for Green Hydrogen Production
Apr 2023
Publication
Hydrogen is known to be the carbon-neutral alternative energy carrier with the highest energy density. Currently more than 95% of hydrogen production technologies rely on fossil fuels resulting in greenhouse gas emissions. Water electrolysis is one of the most widely used technologies for hydrogen generation. Nuclear power a renewable energy source can provide the heat needed for the process of steam electrolysis for clean hydrogen production. This review paper analyses the recent progress in hydrogen generation via high-temperature steam electrolysis through solid oxide electrolysis cells using nuclear thermal energy. Protons and oxygen-ions conducting solid oxide electrolysis processes are discussed in this paper. The scope of this review report covers a broad range including the recent advances in material development for each component (i.e. hydrogen electrode oxygen electrode electrolyte interconnect and sealant) degradation mechanisms and countermeasures to mitigate them.
Advances in Methanol Production and Utilization, with Particular Emphasis toward Hydrogen Generation via Membrane Reactor Technology
Oct 2018
Publication
Methanol is currently considered one of the most useful chemical products and is a promising building block for obtaining more complex chemical compounds such as acetic acid methyl tertiary butyl ether dimethyl ether methylamine etc. Methanol is the simplest alcohol appearing as a colorless liquid and with a distinctive smell and can be produced by converting CO2 and H2 with the further benefit of significantly reducing CO2 emissions in the atmosphere. Indeed methanol synthesis currently represents the second largest source of hydrogen consumption after ammonia production. Furthermore a wide range of literature is focused on methanol utilization as a convenient energy carrier for hydrogen production via steam and autothermal reforming partial oxidation methanol decomposition or methanol–water electrolysis reactions. Last but not least methanol supply for direct methanol fuel cells is a well-established technology for power production. The aim of this work is to propose an overview on the commonly used feedstocks (natural gas CO2 or char/biomass) and methanol production processes (from BASF—Badische Anilin und Soda Fabrik to ICI—Imperial Chemical Industries process) as well as on membrane reactor technology utilization for generating high grade hydrogen from the catalytic conversion of methanol reviewing the most updated state of the art in this field.
Carbon-negative Hydrogen Production (HyBECCS): An Exemplary Techno-economic and Environmental Assessment
Sep 2023
Publication
An exemplary techno-economic and environmental assessment of carbon-negative hydrogen (H2) production is carried out in this work. It is based on the so-called “dark photosynthesis” with carbon dioxide (CO2) capture and geological storage. As a special feature of the assessment the economic consequences due to the impact on the global climate are taken into account. The results indicate that the example project would be capable of generating negative GHG emissions under the assumptions made. The amount is estimated to be 17.72 kgCO2 to be removed from the atmosphere per kilogram of H2 produced. The levelized costs of carbon-negative hydrogen are obtained considering the economic impact of greenhouse gas emissions and removals. They are estimated to be 0.013 EUR/kWhH2. Compared to grey hydrogen from natural gas (0.12 EUR/kWhH2) and green hydrogen from electrolysis using renewable electricity (0.18 EUR/kWhH2) this shows a potential environmental-economic advantage of the considered example. Even without internalization of GHG impacts an economic advantage of the project (0.12 EUR/kWhH2) over green hydrogen (0.17 EUR/kWhH2) is indicated. Compared to other NETs the GHG removal efficiency is at the lower end of both BECCS and DACCS approaches.
Decarbonisation of Geographical Islands and the Feasibility of Green Hydrogen Production Using Excess Electricity
May 2023
Publication
Islands face limitations in producing and transporting energy due to their geographical constraints. To address this issue the ROBINSON project funded by the EU aims to create a flexible self-sufficient and environmentally friendly energy system that can be used on isolated islands. The feasibility of renewable electrification and heating system decarbonization of Eigerøy in Norway is described in this article. A mixed-integer linear programming framework was used for modelling. The optimization method is designed to be versatile and adaptable to suit individual scenarios with a flexible and modular formulation that can accommodate boundary conditions specific to each case. Onshore and offshore wind farms and utility-scale photovoltaic (PV) were considered to generate renewable electricity. Each option was found to be feasible under certain conditions. The heating system composed of a biomass gasifier a combined heat and power system with a gas boiler as backup unit was also analyzed. Parameters were identified in which the combination of all three thermal units represented the best system option. In addition the possibility of green hydrogen production based on the excess electricity from each scenario was evaluated.
Research Progress of Hydrogen Production Technology and Related Catalysts by Electrolysis of Water
Jun 2023
Publication
As a clean and renewable energy source for sustainable development hydrogen energy has gained a lot of attention from the general public and researchers. Hydrogen production by electrolysis of water is the most important approach to producing hydrogen and it is also the main way to realize carbon neutrality. In this paper the main technologies of hydrogen production by electrolysis of water are discussed in detail; their characteristics advantages and disadvantages are analyzed; and the selection criteria and design criteria of catalysts are presented. The catalysts used in various hydrogen production technologies and their characteristics are emphatically expounded aiming at optimizing the existing catalyst system and developing new high-performance high-stability and low-cost catalysts. Finally the problems and solutions in the practical design of catalysts are discussed and explored.
Climate Change Impacts on Gaseous Hydrogen (H2) Potential Produced by Photovoltaic Electrolysis for Stand-Alone or Grid Applications in Europe
Dec 2022
Publication
The EU’s hydrogen strategy consists of studying the potential for renewable hydrogen to help decarbonize the EU in a cost-effective way. Today hydrogen accounts for less than 2% of Europe’s energy consumption. It is primarily used to produce chemical products. However 96% of this hydrogen production is through natural gas leading to significant amounts of CO2 emissions. In this paper we investigated PV electrolysis H2 gas (noted H2(g)) production for mapping this resource at Europe’s scale. The Cordex/Copernicus RCPs scenarios allow for evaluating the impact of climate changes on the H2 -produced mass and the equivalent energy according to both extreme RCPs scenarios. New linear regressions are investigated to study the great dependence in H2(g) produced masses (kg·yr−1 ) and equivalent energies (MWh·yr−1 ) for European countries. Computational scenarios are investigated from a reference year (2005) to the end of the century (2100) by steps of 5 years. According to RCPs 2.6 (favorable)/8.5 (extreme) 31.7% and 77.4% of Europe’s area presents a decrease of H2(g)-produced masses between 2005 and 2100. For the unfavorable scenario (8.5) only a few regions located in the northeast of France Germany Austria Romania Bulgaria and Greece present a positive balance in H2(g) production for supplying remote houses or smart grids in electricity and heat energy.
R&D Status on Thermochemical IS Process for Hydrogen Production at JAEA
Nov 2012
Publication
Thermochemical hydrogen production process is one of the candidates of industrial fossil fuel free hydrogen production. Japan Atomic Energy Agency (JAEA) has been conducting R&D of the thermochemical water splitting iodine-sulfur (IS) process since the end of 1980s. This paper presents the recent study on the IS process in JAEA. In 2005-2009 test-fabrication of components collection of design database improvement of process components for higher thermal efficiency and proposition of composition measurement method were carried out. On the basis of them the integrity test of process components is carried out in 2010-2014 to examine their integrities in severe process environments. At present a Bunsen reactor which produces acids and incidental equipments has been already manufactured using corrosion resistant materials such as glass lining steel and fluoroplastic lining steel. Flow tests to examine the functionality and integrity of the materials are planned in 2012.
Review of Power-to-X Demonstration Projects in Europe
Sep 2020
Publication
At the heart of most Power-to-X (PtX) concepts is the utilization of renewable electricity to produce hydrogen through the electrolysis of water. This hydrogen can be used directly as a final energy carrier or it can be converted into for example methane synthesis gas liquid fuels electricity or chemicals. Technical demonstration and systems integration are of major importance for integrating PtX into energy systems. As of June 2020 a total of 220 PtX research and demonstration projects in Europe have either been realized completed or are currently being planned. The central aim of this review is to identify and assess relevant projects in terms of their year of commissioning location electricity and carbon dioxide sources applied technologies for electrolysis capacity type of hydrogen post-processing and the targeted field of application. The latter aspect has changed over the years. At first the targeted field of application was fuel production for example for hydrogen buses combined heat and power generation and subsequent injection into the natural gas grid. Today alongside fuel production industrial applications are also important. Synthetic gaseous fuels are the focus of fuel production while liquid fuel production is severely under-represented. Solid oxide electrolyzer cells (SOECs) represent a very small proportion of projects compared to polymer electrolyte membranes (PEMs) and alkaline electrolyzers. This is also reflected by the difference in installed capacities. While alkaline electrolyzers are installed with capacities between 50 and 5000 kW (2019/20) and PEM electrolyzers between 100 and 6000 kW SOECs have a capacity of 150 kW. France and Germany are undertaking the biggest efforts to develop PtX technologies compared to other European countries. On the whole however activities have progressed at a considerably faster rate than had been predicted just a couple of years ago.
A Low-temperature Ammonia Electrolyser for Wastewater Treatment and Hydrogen Production
May 2023
Publication
Ammonia is a pollutant present in wastewater and is also a valuable carbon-free hydrogen carrier. Stripping recovery and anodic oxidation of ammonia to produce hydrogen via electrolysis is gaining momentum as a technology yet the development of an inexpensive stable catalytic material is imperative to reduce cost. Here we report on a new nickel copper (NiCu) catalyst electrodeposited onto a high surface area nickel felt (NF) as an anode for ammonia electrolysis. Cyclic voltammetry demonstrated that the catalyst/substrate combination reached the highest current density (200 mA cm2 at 20 C) achieved for a non-noble metal catalyst. A NiCu/NF electrode was tested in an anion exchange membrane electrolyser for 50 h; it showed good stability and high Faradaic efficiency for ammonia oxidation (88%) and hydrogen production (99%). We demonstrate that this novel electrode catalyst/substrate material combination can oxidise ammonia in a scaled system and hydrogen can be produced as a valuable by-product at industrial-level current densities and cell voltages lower than that for water electrolysis.
Performance Assessment of a Solar Powered Hydrogen Production System and its ANFIS Model
Oct 2020
Publication
Apart from many limitations the usage of hydrogen in different day-to-day applications have been increasing drastically in recent years. However numerous techniques available to produce hydrogen electrolysis of water is one of the simplest and cost-effective hydrogen production techniques. In this method water is split into hydrogen and oxygen by using external electric current. In this research a novel hydrogen production system incorporated with Photovoltaic – Thermal (PVT) solar collector is developed. The influence of different parameters like solar collector tilt angle thermal collector design and type of heat transfer fluid on the performance of PVT system and hydrogen production system are also discussed. Finally thermal efficiency electrical efficiency and hydrogen production rate have been predicted by using the Adaptive Neuro-Fuzzy Inference System (ANFIS) technique. Based on this study results it can be inferred that the solar collector tilt angle plays a significant role to improve the performance of the electrical and thermal performance of PVT solar system and Hydrogen yield rate. On the other side the spiral-shaped thermal collector with water exhibited better end result than the other hydrogen production systems. The predicted results ANFIS techniques represent an excellent agreement with the experimental results. In consequence it is suggested that the developed ANFIS model can be adopted for further studies to predict the performance of the hydrogen production system.
Exploring the Potential of Green Hydrogen Production and Application in the Antofagasta Region of Chile
Jun 2023
Publication
Green hydrogen is gaining increasing attention as a key component of the global energy transition towards a more sustainable industry. Chile with its vast renewable energy potential is well positioned to become a major producer and exporter of green hydrogen. In this context this paper explores the prospects for green hydrogen production and use in Chile. The perspectives presented in this study are primarily based on a compilation of government reports and data from the scientific literature which primarily offer a theoretical perspective on the efficiency and cost of hydrogen production. To address the need for experimental data an ongoing experimental project was initiated in March 2023. This project aims to assess the efficiency of hydrogen production and consumption in the Atacama Desert through the deployment of a mobile on-site laboratory for hydrogen generation. The facility is mainly composed by solar panels electrolyzers fuel cells and a battery bank and it moves through the Atacama Desert in Chile at different altitudes from the sea level to measure the efficiency of hydrogen generation through the energy approach. The challenges and opportunities in Chile for developing a robust green hydrogen economy are also analyzed. According to the results Chile has remarkable renewable energy resources particularly in solar and wind power that could be harnessed to produce green hydrogen. Chile has also established a supportive policy framework that promotes the development of renewable energy and the adoption of green hydrogen technologies. However there are challenges that need to be addressed such as the high capital costs of green hydrogen production and the need for supportive infrastructure. Despite these challenges we argue that Chile has the potential to become a leading producer and exporter of green hydrogen or derivatives such as ammonia or methanol. The country’s strategic location political stability and strong commitment to renewable energy provide a favorable environment for the development of a green hydrogen industry. The growing demand for clean energy and the increasing interest in decarbonization present significant opportunities for Chile to capitalize on its renewable energy resources and become a major player in the global green hydrogen market.
Recent Advancements of Polymeric Membranes in Anion Exchange Membrane Water Electrolyzer (AEMWE): A Critical Review
Apr 2023
Publication
The formation of green hydrogen from water electrolysis is one of the supreme methodologies for understanding the well-organized consumption of sporadic renewable energies and the carbon-free future. Among the different electrolysis techniques the evolving anion exchange membrane water electrolysis (AEMWE) shows the utmost promise for manufacturing green hydrogen in an inexpensive way. In the present review we establish the most current and noteworthy achievements of AEMWE which include the advancements in increasing the ionic conductivity and understanding the mechanism of degradation of AEM and the most important topics regarding the designing of the electrocatalyst. The crucial issues that affect the AEMWE behavior are highlighted and future constraints and openings are also discussed. Furthermore this review article provides the appreciated strategies for producing extremely dynamic and robust electrocatalysts and evolving the construction of AEMWE equipment.
Thermochemical Looping Technologies for Clean Hydrogen Production – Current Status and Recent Advances
Nov 2022
Publication
This review critically analyses various aspects of the most promising thermochemical cycles for clean hydrogen production. While the current hydrogen market heavily relies on fossil-fuel-based platforms the thermochemical water-splitting systems based on the reduction-oxidation (redox) looping reactions have a significant potential to significantly contribute to the sustainable production of green hydrogen at scale. However compared to the water electrolysis techniques the thermochemical cycles suffer from a low technology readiness level (TRL) which retards the commercial implementation of these technologies. This review mainly focuses on identifying the capability of the state-of-the-art thermochemical cycles to deploy large-scale hydrogen production plants and their techno-economic performance. This study also analyzed the potential integration of the hybrid looping systems with the solar and nuclear reactor designs which are evidenced to be more cost-effective than the electrochemical water-splitting methods but it excludes fossil-based thermochemical processes such as gasification steam methane reforming and pyrolysis. Further investigation is still required to address the technical issues associated with implementing the hybrid thermochemical cycles in order to bring them to the market for sustainable hydrogen production.
Oxy-fuel Combustion-based Blue Hydrogen Production with the Integration of Water Electrolysis
Jun 2023
Publication
Blue hydrogen is gaining attention as an intermediate step toward achieving eco-friendly green hydrogen production. However the general blue hydrogen production requires an energy-intensive process for carbon capture and storage resulting in low process efficiency. Additionally the hydrogen production processes steam methane reforming (SMR) and electrolysis emits waste heat and byproduct oxygen respectively. To solve these problems this study proposes an oxy-fuel combustion-based blue hydrogen production process that integrates fossil fuel-based hydrogen production and electrolysis processes. The proposed processes are SMR + SOEC and SMR + PEMEC whereas SMR solid oxide electrolysis cell (SOEC) and proton exchange membrane electrolysis cell (PEMEC) are also examined for comparison. In the proposed processes the oxygen produced by the electrolyzer is utilized for oxy-fuel combustion in the SMR process and the resulting flue gas containing CO2 and H2O is condensed to easily separate CO2. Additionally the waste heat from the SMR process is recovered to heat the feed water for the electrolyzer thereby maximizing the process efficiency. Techno-economic sensitivity and greenhouse gas (GHG) analyses were conducted to evaluate the efficiency and feasibility of the proposed processes. The results show that SMR + SOEC demonstrated the highest thermal efficiency (85.2%) and exergy efficiency (80.5%) exceeding the efficiency of the SMR process (78.4% and 70.4% for thermal and exergy efficiencies respectively). Furthermore the SMR + SOEC process showed the lowest levelized cost of hydrogen of 6.21 USD/kgH2. Lastly the SMR + SOEC demonstrated the lowest life cycle GHG emissions. In conclusion the proposed SMR + SOEC process is expected to be a suitable technology for the transition from gray to green hydrogen.
The Origin and Occurrence of Natural Hydrogen
Mar 2023
Publication
Hydrogen is an attractive clean sustainable energy source primarily produced via industry. At present most reviews on hydrogen mainly focus on the preparation and storage of hydrogen while the development and utilization of natural hydrogen will greatly reduce its cost. Natural hydrogen has been discovered in many geological environments. Therefore based on extensive literature research in this study the distribution and sources of natural hydrogen were systematically sorted and the identification method and occurrence state of natural hydrogen were examined and summarized. The results of this research show that hydrogen has been discovered in oceanic spreading centers transform faults passive margins convergent margins and intraplate settings. The primary sources of the hydrogen include alterations in Fe(II)-containing rocks the radiolysis of water degassed magma and the reaction of water- and silica-containing rocks during the mechanical fracturing. Hydrogen can appear in free gas it can be adsorbed and trapped in inclusions. Currently natural hydrogen exploration is in its infancy. This systematic review helps to understand the origin distribution and occurrence pattern of natural hydrogen. In addition it facilitates the exploration and development of natural hydrogen deposits thus enabling the production of low-cost hydrogen.
Designing Off-grid Green Hydrogen Plants Using Dynamic Polymer Electrolyte Membrane Electrolyzers to Minimize the Hydrogen Production Cost
Oct 2023
Publication
Hydrogen produced from electrolysis is an attractive carbon-free fuel and feedstock but potential benefits depend on the carbon intensity of electricity production. This study uses technoeconomic modeling to analyze the benefits of producing zero-carbon hydrogen through dynamically operated polymer electrolyte membrane electrolyzers connected to photovoltaic and wind variable renewable energy (VRE) sources. Dynamic operation is considered for current densities between 0 and 6 A cm2 and compared to a constant current density of 2 A cm2 for different combinations of VRE to electrolysis (VRE:E) capacity ratios and compositions of photovoltaic and wind energy in four locations across the United States. For optimal VRE:E and wind:photovoltaic capacity ratios dynamic operation is found to reduce the levelized cost of hydrogen by 5%–9% while increasing hydrogen production by 134%–173% and decreasing excess electrical power by 82%–95%. The framework herein may be used to determine the optimal VRE:E capacity and VRE mix for dynamically operated green hydrogen systems.
Analysis of Control-System Strategy and Design of a Small Modular Reactor with Different Working Fluids for Electricity and Hydrogen Production as Part of a Decentralised Mini Grid
Mar 2022
Publication
Hydrogen is increasingly being viewed as a significant fuel for future industrial processes as it offers pathways to zero emission. The UK sees hydrogen as one of a handful of low-carbon solutions for transition to net zero. Currently most hydrogen production is from steam reforming of natural gas or coal gasification both of which involve the release of carbon dioxide. Hydrogen production from mini decentralised grids via a thermochemical process coupled with electricity production could offer favourable economics for small modular reactors (SMRs) whereby demand or grid management as a solution would include redirecting the power for hydrogen production when electricity demand is low. It also offers a clean-energy alternative to the aforementioned means. SMRs could offer favourable economics due to their flexible power system as part of the dual-output function. This study objective is to investigate the critical performance parameters associated with the nuclear power plant (NPP) the cycle working fluids and control-system design for switching between electricity and hydrogen demand to support delivery as part of a mini grid system for a reactor power delivering up to approximately 600 MWth power. The novelty of the work is in the holistic parametric analysis undertaken using a novel in-house tool which analyses the NPP using different working fluids with a control function bolt-on at the offtake for hydrogen production. The results indicate that the flow conditions at the offtake can be maintained. The choice of working fluids affects the pressure component. However the recuperator and heat-exchanger effectiveness are considered as efficiency-limiting factors for hydrogen production and electricity generation. As such the benefit of high-technology heat exchangers cannot be underestimated. This is also true when deciding on the thermochemical process to bolt onto the plant. The temperature of the gas at the end of the pipeline should also be considered to ensure that the minimum temperature-requirement status for hydrogen production is me
Global Demand Analysis for Carbon Dioxide as Raw Material from Key Industrial Sources and Direct Air Capture to Produce Renewable Electricity-based Fuels and Chemicals
Sep 2022
Publication
Defossilisation of the current fossil fuels dominated global energy system is one of the key goals in the upcoming decades to mitigate climate change. Sharp reduction in the costs of solar photovoltaics wind power and battery technologies enables a rapid transition of the power and some segments of the transport sectors to sustainable energy resources. However renewable electricity-based fuels and chemicals are required for the defossilisation of hard-to-abate segments of transport and industry. The global demand for carbon dioxide as raw material for the production of e-fuels and e-chemicals during a global energy transition to 100% renewable energy is analysed in this research. Carbon dioxide capture and utilisation potentials from key industrial point sources including cement mills pulp and paper mills and waste incinerators are evaluated. According to this study’s estimates the demand for carbon dioxide increases from 0.6 in 2030 to 6.1 gigatonnes in 2050. Key industrial point sources can potentially supply 2.1 gigatonnes of carbon dioxide and thus meet the majority of the demand in the 2030s. By 2050 however direct air capture is expected to supply the majority of the demand contributing 3.8 gigatonnes of carbon dioxide annually. Sustainable and unavoidable industrial point sources and direct air capture are vital technologies which may help the world to achieve ambitious climate goals.
Hydrogen Production Using Advanced Reactors by Steam Methane Reforming: A Review
Apr 2023
Publication
The present review focuses on the current progress on harnessing the potential of hydrogen production by Methane Steam Reforming (MSR). First based on the prominent literature in last few years the overall research efforts of hydrogen production using different feed stocks like ethanol ammonia glycerol methanol and methane is presented. The presented data is based on reactor type reactor operating conditions catalyst used and yield of hydrogen to provide a general overview. Then the most widely used process [steam methane reforming (SMR)/ methane steam reforming (MSR)] are discussed. Major advanced reactors the membrane reactors Sorption Enhanced methane steam reforming reactors and micro-reactors are evaluated. The evaluation has been done based on parameters like residence time surface area scale-up coke formation conversion space velocity and yield of hydrogen. The kinetic models available in recently published literature for each of these reactors have been presented with the rate constants and other parameters. The mechanism of coke formation and the rate expressions for the same have also been presented. While membrane reactors and sorption enhanced reactors have lot of advantages in terms of process intensification scale-up to industrial scale is still a challenge due to factors like membrane stability and fouling (in membrane reactors) decrease in yield with increasing WHSV (in case of Sorption Enhanced Reactors). Micro-reactors pose a higher potential in terms of higher yield and very low residence time in seconds though the volumes might be substantially lower than present industrial scale conventional reactors.
Life Cycle Assessment of Hydrogen Production from Coal Gasification as an Alternative Transport Fuel
Dec 2022
Publication
The gasification of Polish coal to produce hydrogen could help to make the country independent of oil and gas imports and assist in the rational energy transition from gray to green hydrogen. When taking strategic economic or legislative decisions one should be guided not only by the level of CO2 emissions from the production process but also by other environmental impact factors obtained from comprehensive environmental analyses. This paper presents an analysis of the life cycle of hydrogen by coal gasification and its application in a vehicle powered by FCEV cells. All the main stages of hydrogen fuel production by Shell technology as well as hydrogen compression and transport to the distribution point are included in the analyses. In total two fuel production scenarios were considered: with and without sequestration of the carbon dioxide captured in the process. Life cycle analysis was performed according to the procedures and assumptions proposed in the FC-Hy Guide Guidance Document for performing LCAs on Fuel Cells and H2 Technologies by the CML baseline method. By applying the CO2 sequestration operation the GHG emissions rate for the assumed functional unit can be reduced by approximately 44% from 34.8 kg CO2-eq to 19.5 kg CO2-eq but this involves a concomitant increase in the acidification rate from 3.64·10−2 kg SO2-eq to 3.78·10−2 kg SO2-eq in the eutrophication index from 5.18·10−2 kg PO3− 4-eq to 5.57·10−2 kg PO3− 4-eq and in the abiotic depletion index from 405 MJ to 414 MJ and from 1.54·10−5 kg Sbeq to 1.61·10−5 kg Sbeq.
Production of Hydrogen from Offshore Wind in China and Cost-competitive Supply to Japan
Nov 2021
Publication
The Japanese government has announced a commitment to net-zero greenhouse gas emissions by 2050. It envisages an important role for hydrogen in the nation’s future energy economy. This paper explores the possibility that a significant source for this hydrogen could be produced by electrolysis fueled by power generated from offshore wind in China. Hydrogen could be delivered to Japan either as liquid or bound to a chemical carrier such as toluene or as a component of ammonia. The paper presents an analysis of factors determining the ultimate cost for this hydrogen including expenses for production storage conversion transport and treatment at the destination. It concludes that the Chinese source could be delivered at a volume and cost consistent with Japan’s idealized future projections.
Renewable Energy Pathways toward Accelerating Hydrogen Fuel Production: Evidence from Global Hydrogen Modeling
Dec 2022
Publication
Fossil fuel consumption has triggered worries about energy security and climate change; this has promoted hydrogen as a viable option to aid in decarbonizing global energy systems. Hydrogen could substitute for fossil fuels in the future due to the economic political and environmental concerns related to energy production using fossil fuels. However currently the majority of hydrogen is produced using fossil fuels particularly natural gas which is not a renewable source of energy. It is therefore crucial to increase the efforts to produce hydrogen from renewable sources rather from the existing fossil-based approaches. Thus this study investigates how renewable energy can accelerate the production of hydrogen fuel in the future under three hydrogen economy-related energy regimes including nuclear restrictions hydrogen and city gas blending and in the scenarios which consider the geographic distribution of carbon reduction targets. A random effects regression model has been utilized employing panel data from a global energy system which optimizes for cost and carbon targets. The results of this study demonstrate that an increase in renewable energy sources has the potential to significantly accelerate the growth of future hydrogen production under all the considered policy regimes. The policy implications of this paper suggest that promoting renewable energy investments in line with a fairer allocation of carbon reduction efforts will help to ensure a future hydrogen economy which engenders a sustainable low carbon society.
Centralized Offshore Hydrogen Production from Wind Farms in the Baltic Sea Area—A Study Case for Poland
Aug 2023
Publication
In Poland hydrogen production should be carried out using renewable energy sources particularly wind energy (as this is the most efficient zero-emission technology available). According to hydrogen demand in Poland and to ensure stability as well as security of energy supply and also the realization of energy policy for the EU it is necessary to use offshore wind energy for direct hydrogen production. In this study a centralized offshore hydrogen production system in the Baltic Sea area was presented. The goal of our research was to explore the possibility of producing hydrogen using offshore wind energy. After analyzing wind conditions and calculating the capacity of the proposed wind farm a 600 MW offshore hydrogen platform was designed along with a pipeline to transport hydrogen to onshore storage facilities. Taking into account Poland’s Baltic Sea area wind conditions with capacity factor between 45 and 50% and having obtained results with highest monthly average output of 3508.85 t of hydrogen it should be assumed that green hydrogen production will reach profitability most quickly with electricity from offshore wind farms.
Urban Hydrogen Production Model Using Environmental Infrastructures to Achieve the Net Zero Goal
Dec 2022
Publication
Land available for energy production is limited in cities owing to high population density. To reach the net zero goal cities contributing 70% of overall greenhouse gas emissions need to dramatically reduce emissions and increase self-sufficiency in energy production. Environmental infrastructures such as sewage treatment and incineration plants can be used as energy production facilities in cities. This study attempted to examine the effect of using environmental infrastructure such as energy production facilities to contribute toward the carbon neutrality goal through urban energy systems. In particular since the facilities are suitable for hydrogen supply in cities the analysis was conducted focusing on the possibility of hydrogen production. First the current status of energy supply and demand and additional energy production potential in sewage treatment and incineration plants in Seoul were analyzed. Then the role of these environmental infrastructures toward energy self-sufficiency in the urban system was examined. This study confirmed that the facilities can contribute to the city’s energy self-sufficiency and the achievement of its net-zero goal.
Environmental Assessment of Hydrogen Utilization in Various Applications and Alternative Renewable Sources for Hydrogen Production: A Review
May 2023
Publication
Rapid industrialization is consuming too much energy and non-renewable energy resources are currently supplying the world’s majority of energy requirements. As a result the global energy mix is being pushed towards renewable and sustainable energy sources by the world’s future energy plan and climate change. Thus hydrogen has been suggested as a potential energy source for sustainable development. Currently the production of hydrogen from fossil fuels is dominant in the world and its utilization is increasing daily. As discussed in the paper a large amount of hydrogen is used in rocket engines oil refining ammonia production and many other processes. This paper also analyzes the environmental impacts of hydrogen utilization in various applications such as iron and steel production rocket engines ammonia production and hydrogenation. It is predicted that all of our fossil fuels will run out soon if we continue to consume them at our current pace of consumption. Hydrogen is only ecologically friendly when it is produced from renewable energy. Therefore a transition towards hydrogen production from renewable energy resources such as solar geothermal and wind is necessary. However many things need to be achieved before we can transition from a fossil-fuel-driven economy to one based on renewable energy
Multilevel Governance, PV Solar Energy, and Entrepreneurship: The Generation of Green Hydrogen as a Fuel of Renewable Origin
Sep 2022
Publication
In Spain the institutional framework for photovoltaic energy production has experienced distinct stages. From 2007 to 2012 the feed-in-tariff system led to high annual growth rates of this renewable energy but after the suppression of the policy of public subsidies the sector stagnated. In recent years green hydrogen an innocuous gas in the atmosphere has become a driving force that stimulates photovoltaic energy production. Since 2020 encouraged by the European energy strategies and corresponding funds Spain has established a regulation to promote green hydrogen as a form of energy resource. Adopting the new institutional economics (NIE) approach this article investigates the process of changing incentives for the energy business sector and its impact on photovoltaic energy production. The results show an increase in the number of both projects approved or on approval and companies involved in green hydrogen that are planning to use photovoltaic energy in Spain thus engendering the creation of a new photovoltaic business environment based on innovation and sustainability.
Optimisation of Size and Control Strategy in Utility-scale of Green Hydrogen Production Systems
Aug 2023
Publication
The optimisation of green hydrogen production systems is challenging. Moreover an accurate simulation of the system is required for effective optimisation. This study presents a novel method for optimising utility-scale hybrid photovoltaice-wind systems for hydrogen production using accurate simulation models. The optimisation objective is to minimise the levelised cost of hydrogen (LCOH) using genetic algorithms. Different types of systems (such as islanded systems grid-connected systems with or without the possibility of purchasing electricity from the grid and grid-connected systems considering power curtailment) are evaluated and optimised. Each combination of components and control strategy is simulated during the system lifetime (20 yrs) in time steps of 5 min considering the degradation of renewable generators during the system lifetime and different real-time pricing curves and renewable resource curves for each year of the system lifetime. Accurate models are used in the simulations including electrolyser efficiency dependent on the input power and cold-start extra ageing. An application example located in Zaragoza (Spain) is shown obtaining LCOH from 4.74 to 16.06 V/kg depending on the type of project and electrolyser.
Review on Bubble Dynamics in Proton Exchange Membrane Water Electrolysis: Towards Optimal Green Hydrogen Yield
Dec 2023
Publication
Water electrolysis using a proton exchange membrane (PEM) holds substantial promise to produce green hydrogen with zero carbon discharge. Although various techniques are available to produce hydrogen gas the water electrolysis process tends to be more cost-effective with greater advantages for energy storage devices. However one of the challenges associated with PEM water electrolysis is the accumulation of gas bubbles which can impair cell performance and result in lower hydrogen output. Achieving an in-depth knowledge of bubble dynamics during electrolysis is essential for optimal cell performance. This review paper discusses bubble behaviors measuring techniques and other aspects of bubble dynamics in PEM water electrolysis. It also examines bubble behavior under different operating conditions as well as the system geometry. The current review paper will further improve the understanding of bubble dynamics in PEM water electrolysis facilitating more competent inexpensive and feasible green hydrogen production.
Techno-economic Investigation of Electricity and Hydrogen Production from Wind Energy in Casablanca, Morocco
Dec 2018
Publication
The aim of this study is to investigate the technical and economic potential of electricity and hydrogen production in Casablanca Morocco. For this reason we simulated the performance of a 4.2 MWp wind turbine if installed in Casablanca. The results show that the electricity and hydrogen production varies greatly through the year due to the high fluctuation in wind speed. The annual electricity and hydrogen production is 29.16 GWh and 555 Tons respectively. As for the levelized cost of production the LCOE was found to be 0.24 $/kWh and the H2 LCO were equal to 13.52 $/Kg.
Spatial Succession for Degradation of Solid Multicomponent Food Waste and Purification of Toxic Leachate with the Obtaining of Biohydrogen and Biomethane
Jan 2022
Publication
A huge amount of organic waste is generated annually around the globe. The main sources of solid and liquid organic waste are municipalities and canning and food industries. Most of it is disposed of in an environmentally unfriendly way since none of the modern recycling technologies can cope with such immense volumes of waste. Microbiological and biotechnological approaches are extremely promising for solving this environmental problem. Moreover organic waste can serve as the substrate to obtain alternative energy such as biohydrogen (H2 ) and biomethane (CH4 ). This work aimed to design and test new technology for the degradation of food waste coupled with biohydrogen and biomethane production as well as liquid organic leachate purification. The effective treatment of waste was achieved due to the application of the specific granular microbial preparation. Microbiological and physicochemical methods were used to measure the fermentation parameters. As a result a four-module direct flow installation efficiently couples spatial succession of anaerobic and aerobic bacteria with other micro- and macroorganisms to simultaneously recycle organic waste remediate the resulting leachate and generate biogas.
Techno-economic Analysis of Large-scale Green Hydrogen Production and Storage
Jun 2023
Publication
Producing clean energy and minimising energy waste are essential to achieve the United Nations sustainable development goals such as Sustainable Development Goal 7 and 13. This research analyses the techno-economic potential of waste heat recovery from multi-MW scale green hydrogen production. A 10 MW proton exchange membrane electrolysis process is modelled with a heat recovery system coupled with an organic Rankine cycle (ORC) to drive the mechanical compression of hydrogen. The technical results demonstrate that when implementing waste heat recovery coupled with an ORC the first-law efficiency of electrolyser increases from 71.4% to 98%. The ORC can generate sufficient power to drive the hydrogen's compression from the outlet pressure at the electrolyser 30 bar up to 200 bar. An economic analysis is conducted to calculate the levelised cost of hydrogen (LCOH) of system and assess the feasibility of implementing waste heat recovery coupled with ORC. The results reveal that electricity prices dominate the LCOH. When electricity prices are low (e.g. dedicated offshore wind electricity) the LCOH is higher when implementing heat recovery. The additional capital expenditure and operating expenditure associated with the ORC increases the LCOH and these additional costs outweigh the savings generated by not purchasing electricity for compression. On the other hand heat recovery and ORC become attractive and feasible when grid electricity prices are higher.
Hydrogen from Waste Gasification
Feb 2024
Publication
Hydrogen is a versatile energy vector for a plethora of applications; nevertheless its production from waste/residues is often overlooked. Gasification and subsequent conversion of the raw synthesis gas to hydrogen are an attractive alternative to produce renewable hydrogen. In this paper recent developments in R&D on waste gasification (municipal solid waste tires plastic waste) are summarised and an overview about suitable gasification processes is given. A literature survey indicated that a broad span of hydrogen relates to productivity depending on the feedstock ranging from 15 to 300 g H2/kg of feedstock. Suitable gas treatment (upgrading and separation) is also covered presenting both direct and indirect (chemical looping) concepts. Hydrogen production via gasification offers a high productivity potential. However regulations like frame conditions or subsidies are necessary to bring the technology into the market.
Natural Hydrogen the Fuel of the 21st Century
Jun 2019
Publication
Much has been learned about natural hydrogen (H2) seepages and accumulation but present knowledge of hydrogen behavior in the crust is so limited that it is not yet possible to consider exploitation of this resources. Hydrogen targeting requires a shift in the long-standing paradigms that drive oil and gas exploration. This paper describes the foundation of an integrated source-to-sink view of the hydrogen cycle and propose preliminary practical guidelines for hydrogen exploration.
Italian Offshore Platform and Depleted Reservoir Conversion in the Energy Transition Perspective
Aug 2023
Publication
New hypotheses for reusing platforms reaching their end-of-life have been investigated in several works discussing the potential conversions of these infrastructures from recreational tourism to fish farming. In this perspective paper we discuss the conversion options that could be of interest in the context of the current energy transition with reference to the off-shore Italian scenario. The study was developed in support of the development of a national strategy aimed at favoring a circular economy and the reuse of existing infrastructure for the implementation of the energy transition. Thus the investigated options include the onboard production of renewable energy hydrogen production from seawater through electrolyzers CO2 capture and valorization and platform reuse for underground fluid storage in depleted reservoirs once produced through platforms. Case histories are developed with reference to a typical fictitious platform in the Adriatic Sea Italy to provide an engineering-based approach to these different conversion options. The coupling of the platform with the underground storage to set the optimal operational conditions is managed through the forecast of the reservoir performance with advanced numerical models able to simulate the complexity of the phenomena occurring in the presence of coupled hydrodynamic geomechanical geochemical thermal and biological processes. The results of our study are very encouraging because they reveal that no technical environmental or safety issues prevent the conversion of offshore platforms into valuable infrastructure contributing to achieving the energy transition targets as long as the selection of the conversion option to deploy is designed taking into account the system specificity and including the depleted reservoir to which it is connected when relevant. Socio-economic issues were not investigated as they were out of the scope of the project.
Proton Exchange Membrane Electrolyzer Modeling for Power Electronics Control: A Short Review
May 2020
Publication
The main purpose of this article is to provide a short review of proton exchange membrane electrolyzer (PEMEL) modeling used for power electronics control. So far three types of PEMEL modeling have been adopted in the literature: resistive load static load (including an equivalent resistance series-connected with a DC voltage generator representing the reversible voltage) and dynamic load (taking into consideration the dynamics both at the anode and the cathode). The modeling of the load is crucial for control purposes since it may have an impact on the performance of the system. This article aims at providing essential information and comparing the different load modeling.
Study on Enhancing Hydrogen Production Potential from Renewable Energy in Multi-terminal DC System
Aug 2021
Publication
Renewable energy complementary hydrogen production can enhance the full consumption of renewable energy and reduce the abandonment of wind and solar power. The integration of renewable energy and hydrogen production equipment through existing multi-terminal DC systems can reduce new power lines construction and save investment in distribution equipment. For integrated renewable energy/hydrogen energy in an existing multi-terminal DC system this paper investigates its potential of hydrogen production based on renewable energy while ensuring the normal performance of the existing system being not affected. The typical structure and control strategy of the integrated renewable energy/hydrogen energy in multi-terminal DC system are firstly described. Then the state space model of the system is constructed and the key parameters affecting the hydrogen production capacity are studied by using the eigenvalues analysis method. Finally the corresponding system simulation model and test platform are built and the theoretical analysis results are verified and the potential of using multi-terminal DC system to enhance hydrogen production is quantitatively analyzed. The proposed scheme can enhance the hydrogen production potential from renewable energy meanwhile the normal performance of the existing system is not affected.
Techno-Economic Potential of Wind-Based Green Hydrogen Production in Djibouti: Literature Review and Case Studies
Aug 2023
Publication
Disputed supply chains inappropriate weather and low investment followed by the Russian invasion of Ukraine has led to a phenomenal energy crisis especially in the Horn of Africa. Accordingly proposing eco-friendly and sustainable solutions to diversify the access of electricity in the Republic of Djibouti which has no conventional energy resources and is completely energy dependent on its neighboring countries has become a must. Therefore the implementation of sustainable renewable and energy storage systems is nationally prioritized. This paper deals for the first time with the exploitation of such an affordable and carbon-free resource to produce hydrogen from wind energy in the rural areas of Nagad and Bara Wein in Djibouti. The production of hydrogen and the relevant CO2 emission reduction using different De Wind D6 Vestas and Nordex wind turbines are displayed while using Alkaline and Proton Exchange Membrane (PEM) electrolyzers. The Bara Wein and Nagad sites had a monthly wind speed above 7 m/s. From the results the Nordex turbine accompanied with the alkaline electrolyzer provides the most affordable electricity production approximately 0.0032 $/kWh for both sites; this cost is about one per hundred the actual imported hydroelectric energy price. Through the ecological analysis the Nordex turbine is the most suitable wind turbine with a CO2 emission reduction of 363.58 tons for Bara Wein compared to 228.76 tons for Nagad. While integrating the initial cost of wind turbine implementation in the capital investment the mass and the levelized cost of the produced green hydrogen are estimated as (29.68 tons and 11.48 $/kg) for Bara Wein with corresponding values of (18.68 tons and 18.25 $/kg) for Nagad.
Energy and Environmental Assessment of Hydrogen from Biomass Sources: Challenges and Perspectives
Aug 2022
Publication
Hydrogen is considered as one of the pillars of the European decarbonisation strategy boosting a novel concept of the energy system in line with the EU’s commitment to achieve clean energy transition and reach the European Green Deal carbon neutrality goals by 2050. Hydrogen from biomass sources can significantly contribute to integrate the renewable hydrogen supply through electrolysis at large-scale production. Specifically it can cover the non-continuous production of green hydrogen coming from solar and wind energy to offer an alternative solution to such industrial sectors necessitating of stable supply. Biomass-derived hydrogen can be produced either from thermochemical pathways (i.e. pyrolysis liquefaction and gasification) or from biological routes (i.e. direct or indirect-biophotolysis biological water–gas shift reaction photo- and dark-fermentation). The paper reviews several production pathways to produce hydrogen from biomass or biomass-derived sources (biogas liquid bio-intermediates sugars) and provides an exhaustive review of the most promising technologies towards commercialisation. While some pathways are still at low technology readiness level others such as the steam bio-methane reforming and biomass gasification are ready for an immediate market uptake. The various production pathways are evaluated in terms of energy and environmental performances highlighting the limits and barriers of the available LCA studies. The paper shows that hydrogen production technologies from biomass appears today to be an interesting option almost ready to constitute a complementing option to electrolysis.
A Techno-Economic Study for Off-Grid Green Hydrogen Production Plants: The Case of Chile
Jul 2023
Publication
In this study we present a pre-feasibility analysis that examines the viability of implementing autonomous green hydrogen production plants in two strategic regions of Chile. With abundant renewable energy resources and growing interest in decarbonization in Chile this study aims to provide a comprehensive financial analysis from the perspective of project initiators. The assessment includes determining the optimal sizing of an alkaline electrolyzer stack seawater desalination system and solar and wind renewable energy farms and the focus is on conducting a comprehensive financial analysis from the perspective of project initiators to assess project profitability using key economic indicators such as net present value (NPV). The analyses involve determining appropriate sizing of an alkaline electrolyzer stack a seawater desalination system and solar and wind renewable energy farms. Assuming a base case production of 1 kiloton per year of hydrogen the capital expenditures (CAPEX) and operating expenses (OPEX) are determined. Then the manufacturing and production costs per kilogram of green hydrogen are calculated resulting in values of USD 3.53 kg−1 (utilizing wind energy) and USD 5.29 kg−1 (utilizing photovoltaic solar energy). Cash flows are established by adjusting the sale price of hydrogen to achieve a minimum expected return on investment of 4% per year yielding minimum prices of USD 7.84 kg−1 (with wind energy) and USD 11.10 kg−1 (with photovoltaic solar energy). Additionally a sensitivity analysis is conducted to assess the impact of variations in investment and operational costs. This research provides valuable insights into the financial feasibility of green hydrogen production in Chile contributing to understanding renewable energy-based hydrogen projects and their potential economic benefits. These results can provide a reference for future investment decisions and the global development of green hydrogen production plants.
Modeling of Hydrogen Production System for Photovoltaic Power Generation and Capacity Optimization of Energy Storage System
Sep 2022
Publication
Hydrogen production using solar energy is an important way to obtain hydrogen energy. However the inherent intermittent and random characteristics of solar energy reduce the efficiency of hydrogen production. Therefore it is necessary to add an energy storage system to the photovoltaic power hydrogen production system. This paper establishes a model of a photovoltaic power generation hydrogen system and optimizes the capacity configuration. Firstly the mathematical model is modeled and analyzed and the system is modeled using Matlab/Simulink; secondly the principle of optimal configuration of energy storage capacity is analyzed to determine the optimization strategy we propose the storage capacity configuration algorithm based on the low-pass filtering principle and optimal time constant selection; finally a case study is conducted whose photovoltaic installed capacity of 30 MW verifying the effectiveness of the proposed algorithm analyzing the relationship between energy storage capacity and smoothing effect. The results show that as the cut-off frequency decreases the energy storage capacity increases and the smoothing effect is more obvious. The proposed algorithm can effectively reduce the 1 h maximum power variation of PV power generation. In which the maximum power variation of PV generation 1 h before smoothing is 4.31 MW. We set four different sets of time constants the maximum power variation of PV generation 1 h after smoothing is reduced to 0.751 0.389 0.078 and 0.04 MW respectively.
Towards a Multi-color Hydrogen Production Network? Competing Imaginaries of Development in Northern Patagonia, Argentina
Feb 2024
Publication
Green hydrogen has recently gained importance as a key element in the transition to a low-carbon energy future sparking a boom in possible production regions. This article aims at situating incipient hydrogen production in the Argentine province of Río Negro within a global production network (GPN). The early configuration of the hydrogen-GPN includes several stakeholders and is contested in many ways. To explore the possible materialization of the hydrogen economy in Argentina this article links GPN literature to the concept of sociotechnical imaginaries. In so doing this study finds three energy imaginaries linked to hydrogen development: First advocates of green hydrogen (GH2) project a sociotechnical imaginary in which GH2 is expected to promote scientific and technological progress. Second proponents of blue hydrogen point to Vaca Muerta and the role of natural gas for energy autonomy. Third opponents of the GH2 project question the underlying growth and export model emphasizing conservation and domestic energy sovereignty. The competition between different capital fractions i.e. green and fossil currently poses the risk of pro-fossil path decisions and lock-in effects. Current power constellations have led to the replacement of green with low-emission resulting in the promotion of multi-colored hydrogen. This is particularly evident in the draft for the new national hydrogen law and the actors involved in defining the national hydrogen strategy. The conceptual combination of actors and their interests their current power relations and the sociotechnical imaginaries they deploy illustrates how Argentina's energy future is already being shaped today.
Hydrogen for Harvesting the Potential of Offshore Wind: A North Sea Case Study
Dec 2023
Publication
Economical offshore wind developments depend on alternatives for cost-efficient transmission of the generated energy to connecting markets. Distance to shore availability of an offshore power grid and scale of the wind farm may impede export through power cables. Conversion to H2 through offshore electrolysis may for certain offshore wind assets be a future option to enable energy export. Here we analyse the cost sensitivity of offshore electrolysis for harvesting offshore wind in the North Sea using a technology-detailed multi-carrier energy system modelling framework for analysis of energy export. We include multiple investment options for electric power and hydrogen export including HVDC cables new hydrogen pipelines tie-in to existing pipelines and pipelines with linepacking. Existing hydropower is included in the modelling and the effect on offshore electrolysis from increased pumping capacity in the hydropower system is analysed. Considering the lack of empirical cost data on offshore electrolysis as well as the high uncertainty in future electricity and H2 prices we analyse the cost sensitivity of offshore electrolysis in the North Sea by comparing costs relative to onshore electrolysis and energy prices relative to a nominal scenario. Offshore electrolysis is shown to be particularly sensitive to the electricity price and an electricity price of 1.5 times the baseline assumption was needed to provide sufficient offshore energy for any significant offshore electrolysis investments. On the other hand too high electricity prices would have a negative impact on offshore electrolysis because the energy is more valuable as electricity even at the cost of increased wind power curtailment. This shows that there is a window-of-opportunity in terms of onshore electricity where offshore electrolysis can play a significant role in the production of H2 . Pumped hydropower increases the maximum installed offshore electrolysis at the optimal electricity and H2 prices and makes offshore electrolysis more competitive at low electricity prices. Linepacking can make offshore electrolysis investments more robust against low H2 and high electricity prices as it allow for more variable H2 production through storing excess energy from offshore. The increased electrolysis capacity needed for variable electrolyser operation and linepacking is installed onshore due to its lower CAPEX compared to offshore installations.
Electrocatalysts for the Generation of Hydrogen, Oxygen and Synthesis Gas
Sep 2016
Publication
Water electrolysis is the most promising method for efficient production of high purity hydrogen (and oxygen) while the required power input for the electrolysis process can be provided by renewable sources (e.g. solar or wind). The thus produced hydrogen can be used either directly as a fuel or as a reducing agent in chemical processes such as in Fischer–Tropsch synthesis. Water splitting can be realized both at low temperatures (typically below 100 °C) and at high temperatures (steam water electrolysis at 500– 1000 °C) while different ionic agents can be electrochemically transferred during the electrolysis process (OH− H+ O2− ). Singular requirements apply in each of the electrolysis technologies (alkaline polymer electrolyte membrane and solid oxide electrolysis) for ensuring high electrocatalytic activity and long-term stability. The aim of the present article is to provide a brief overview on the effect of the nature and structure of the catalyst–electrode materials on the electrolyzer’s performance. Past findings and recent progress in the development of efficient anode and cathode materials appropriate for large-scale water electrolysis are presented. The current trends limitations and perspectives for future developments are summarized for the diverse electrolysis technologies of water splitting while the case of CO2/H2O co-electrolysis (for synthesis gas production) is also discussed.
Water Consumption from Electrolytic Hydrogen in a Carbon-neutral US Energy System
Feb 2023
Publication
Hydrogen is an energy carrier with potential applications in decarbonizing difficult-to-electrify energy and industrial systems. The environmental profile of hydrogen varies substantially with its inputs. Water consumption is a particular issue of interest as decisions are made about capital and other investments that will affect the scale and scope of hydrogen use. This study focuses on electrolytic hydrogen due to its path to greenhouse gas neutrality and irreducible water demand (though other pathways might be more water intensive). Specifically it evaluates life cycle consumptive freshwater intensity of electrolytic hydrogen in the United States at volumes associated with 12 scenarios for a deeply decarbonized 2050 US energy system from two modeling efforts for which both electricity fuel mix and electrolytic hydrogen production were projected (America’s Zero Carbon Action Plan and Net Zero America) in addition to volumes for a stylized energy storage project (500 MW hydrogen-fired turbine). Freshwater requirements for hydrogen could be large. Under a central estimate for 2050 US electrolytic hydrogen production electrolytic freshwater demand for process and feedstock inputs alone (i.e. excluding water for electricity) would be about 7.5% of total 2014 US freshwater consumption for energy (1 billion cubic meters/year 109 m3 /y; [0.2% 15%] across scenarios for 2050 electrolytic hydrogen production of [0.3 18] exajoules EJ). Including water associated with production of input electricity doubles this central estimate to 15% (2 × 109 m3 /y; [1% 23%] across scenarios). Turbines using electrolytic hydrogen are estimated to be about as freshwater intensive as a coal or nuclear plant assuming decarbonized low-water electricity inputs. Although a decarbonized energy system is projected to require less water for resource capture and electricity conversion than the current fossil-dominated energy system additional conversion processes supporting decarbonization like electrolysis could offset water savings.
Genesis and Energy Significance of Natural Hydrogen
Jan 2023
Publication
H2 is clean energy and an important component of natural gas. Moreover it plays an irreplaceable role in improving the hydrocarbon generation rate of organic matter and activating ancient source rocks to generate hydrocarbon in Fischer-Tropsch (FT) synthesis and catalytic hydrogenation. Compared with hydrocarbon reservoir system a complete hydrogen (H2) accumulation system consists of H2 source,reservoirs and seal. In nature the four main sources of H2 are hydrolysis organic matter degradation the decomposition of substances such as methane and ammonia and deep mantle degassing. Because the complex tectonic activities the H2 produced in a geological environment is generally a mixture of various sources. Compared with the genetic mechanisms of H2 the migration and preservation of H2 especially the H2 trapping are rarely studied. A necessary condition for large-scale H2 accumulation is that the speed of H2 charge is much faster than diffusion loss. Dense cap rock and continuous H2 supply are favorable for H2 accumulation. Moreover H2O in the cap rock pores may provide favorable conditions for short-term H2 accumulation.
Deep Learning for Wind and Solar Energy Forecasting in Hydrogen Production
Feb 2024
Publication
This research delineates a pivotal advancement in the domain of sustainable energy systems with a focused emphasis on the integration of renewable energy sources—predominantly wind and solar power—into the hydrogen production paradigm. At the core of this scientific endeavor is the formulation and implementation of a deep-learning-based framework for short-term localized weather forecasting specifically designed to enhance the efficiency of hydrogen production derived from renewable energy sources. The study presents a comprehensive evaluation of the efficacy of fully connected neural networks (FCNs) and convolutional neural networks (CNNs) within the realm of deep learning aimed at refining the accuracy of renewable energy forecasts. These methodologies have demonstrated remarkable proficiency in navigating the inherent complexities and variabilities associated with renewable energy systems thereby significantly improving the reliability and precision of predictions pertaining to energy output. The cornerstone of this investigation is the deployment of an artificial intelligence (AI)-driven weather forecasting system which meticulously analyzes data procured from 25 distinct weather monitoring stations across Latvia. This system is specifically tailored to deliver short-term (1 h ahead) forecasts employing a comprehensive sensor fusion approach to accurately predicting wind and solar power outputs. A major finding of this research is the achievement of a mean squared error (MSE) of 1.36 in the forecasting model underscoring the potential of this approach in optimizing renewable energy utilization for hydrogen production. Furthermore the paper elucidates the construction of the forecasting model revealing that the integration of sensor fusion significantly enhances the model’s predictive capabilities by leveraging data from multiple sources to generate a more accurate and robust forecast. The entire codebase developed during this research endeavor has been made available on an open access GIT server.
Global Land and Water Limits to Electrolytic Hydrogen Production Using Wind and Solar Resources
Sep 2023
Publication
Proposals for achieving net-zero emissions by 2050 include scaling-up electrolytic hydrogen production however this poses technical economic and environmental challenges. One such challenge is for policymakers to ensure a sustainable future for the environment including freshwater and land resources while facilitating low-carbon hydrogen production using renewable wind and solar energy. We establish a country-by-country reference scenario for hydrogen demand in 2050 and compare it with land and water availability. Our analysis highlights countries that will be constrained by domestic natural resources to achieve electrolytic hydrogen self-sufficiency in a net-zero target. Depending on land allocation for the installation of solar panels or wind turbines less than 50% of hydrogen demand in 2050 could be met through a local production without land or water scarcity. Our findings identify potential importers and exporters of hydrogen or conversely exporters or importers of industries that would rely on electrolytic hydrogen. The abundance of land and water resources in Southern and Central-East Africa West Africa South America Canada and Australia make these countries potential leaders in hydrogen export.
Renewable Hydrogen Production: A Techno-economic Comparison of Photoelectrochemical Cells and Photovoltaic-electrolysis
Aug 2020
Publication
The present paper reports a techno-economic analysis of two solar assisted hydrogen production technologies: a photoelectrochemical (PEC) system and its major competitor a photovoltaic system connected to a conventional water electrolyzer (PV-E system). A comparison between these two types was performed to identify the more promising technology based on the levelized cost of hydrogen (LCOH). The technical evaluation was carried out by considering proven designs and materials for the PV-E system and a conceptually design for the PEC system extrapolated to future commercial scale. The LCOH for the off-grid PV-E system was found to be 6.22 $/kgH2 with a solar to hydrogen efficiency of 10.9%. For the PEC system with a similar efficiency of 10% the LCOH was calculated to be much higher namely 8.43 $/kgH2. A sensitivity analysis reveals a great uncertainty in the LCOH of the prospective PEC system. This implies that much effort would be needed for this technology to become competitive on the market. Therefore we conclude that the potential techno-economic benefits that PEC systems offer over PV-E are uncertain and even in the best case limited. While research into photoelectrochemical cells remains of interest it presents a poor case for dedicated investment in the technology’s development and scale-up.
Levelized Cost of Biohydrogen from Steam Reforming of Biomethane with Carbon Capture and Storage (Golden Hydrogen)—Application to Spain
Feb 2024
Publication
The production of biohydrogen with negative CO2 emissions through the steam methane reforming of biomethane coupled with carbon capture and storage represents a promising technology particularly for industries that are difficult to electrify. In spite of the maturity of this technology which is currently employed in the production of grey and blue hydrogen a detailed cost model that considers the entire supply chain is lacking in the literature. This study addresses this gap by applying correlations derived from actual facilities producing grey and blue hydrogen to calculate the CAPEX while exploring various feedstock combinations for biogas generation to assess the OPEX. The analysis also includes logistic aspects such as decentralised biogas production and the transportation and storage of CO2 . The levelized cost of golden hydrogen is estimated to range from EUR 1.84 to 2.88/kg compared to EUR 1.47/kg for grey hydrogen and EUR 1.93/kg for blue hydrogen assuming a natural gas cost of EUR 25/MWh and excluding the CO2 tax. This range increases to between 3.84 and 2.92 with a natural gas cost of EUR 40/MWh with the inclusion of the CO2 tax. A comparison with conventional green hydrogen is performed highlighting both prices and potential thereby offering valuable information for decision-making.
Research on Hydrogen Production System Technology Based on Photovoltaic-Photothermal Coupling Electrolyzer
Dec 2023
Publication
Solar hydrogen production technology is a key technology for building a clean low-carbon safe and efficient energy system. At present the intermittency and volatility of renewable energy have caused a lot of “wind and light.” By combining renewable energy with electrolytic water technology to produce high-purity hydrogen and oxygen which can be converted into electricity the utilization rate of renewable energy can be effectively improved while helping to improve the solar hydrogen production system. This paper summarizes and analyzes the research status and development direction of solar hydrogen production technology from three aspects. Energy supply mode: the role of solar PV systems and PT systems in this technology is analyzed. System control: the key technology and system structure of different types of electrolytic cells are introduced in detail. System economy: the economy and improvement measures of electrolytic cells are analyzed from the perspectives of cost consumption efficiency and durability. Finally the development prospects of solar hydrogen production systems in China are summarized and anticipated. This article reviews the current research status of photovoltaic-photothermal coupled electrolysis cell systems fills the current research gap and provides theoretical reference for the further development of solar hydrogen production systems.
Renewable-power-assisted Production of Hydrogen and Liquid Hydrocarbons from Natural Gas: Techno-economic Analysis
Jun 2022
Publication
The declining cost of renewable power has engendered growing interest in leveraging this power for the production of chemicals and synthetic fuels. Here renewable power is added to the gas-to-liquid (GTL) process through Fischer–Tropsch (FT) synthesis in order to increase process efficiency and reduce CO2 emissions. Accordingly two realistic configurations are considered which differ primarily in the syngas preparation step. In the first configuration solid oxide steam electrolysis cells (SOEC) in combination with an autothermal reformer (ATR) are used to produce synthesis gas with the right composition while in the second configuration an electrically-heated steam methane reformer (E-SMR) is utilized for syngas production. The results support the idea of adding power to the GTL process mainly by increased process efficiencies and reduced process emissions. Assuming renewable power is available the process emissions would be 200 and 400 gCO2 L1 syncrude for the first and second configurations respectively. Configuration 1 and 2 show 8 and 4 times less emission per liter syncrude produced respectively compared to a GTL plant without H2 addition with a process emission of 1570 gCO2 L1 syncrude. By studying the two designs based on FT production carbon efficiency and FT catalyst volume a better alternative is to add renewable power to the SOEC (configuration 1) rather than using it in an E-SMR (configuration 2). Given an electricity price of $100/MW h and natural gas price of 5 $ per GJ FT syncrude and H2 can be produced at a cost between $15/MW h and $16/MW h. These designs are considered to better utilize the available carbon resources and thus expedite the transition to a low-carbon economy
Review on Techno-economics of Hydrogen Production Using Current and Emerging Processes: Status and Perspectives
Feb 2024
Publication
This review presents a broad exploration of the techno economic evaluation of different technologies utilized in the production of hydrogen from both renewable and non-renewable sources. These encompass methods ranging from extracting hydrogen from fossil fuels or biomass to employing microbial processes electrolysis of water and various thermochemical cycles. A rigorous techno-economic evaluation of hydrogen production technologies can provide a critical cost comparison for future resource allocation priorities and trajectory. This evaluation will have a great impact on future hydrogen production projects and the development of new approaches to reduce overall production costs and make it a cheaper fuel. Different methods of hydrogen production exhibit varying efficiencies and costs: fast pyrolysis can yield up to 45% hydrogen at a cost range of $1.25 to $2.20 per kilogram while gasification operating at temperatures exceeding 750°C faces challenges such as limited small-scale coal production and issues with tar formation in biomass. Steam methane reforming which constitutes 48% of hydrogen output experiences cost fluctuations depending on scale whereas auto-thermal reforming offers higher efficiency albeit at increased costs. Chemical looping shows promise in emissions reduction but encounters economic hurdles and sorptionenhanced reforming achieves over 90% hydrogen but requires CO2 storage. Renewable liquid reforming proves effective and economically viable. Additionally electrolysis methods like PEM aim for costs below $2.30 per kilogram while dark fermentation though cost-effective grapples with efficiency challenges. Overcoming technical economic barriers and managing electricity costs remains crucial for optimizing hydrogen production in a low-carbon future necessitating ongoing research and development efforts.
Techno-economic Analysis of Green-H2@Scale Production
Sep 2023
Publication
The International Energy Agency (IEA) established the "H2 Implementing Agreement (HIA)" to promote H2 transition in various economic sectors. Today less than one percent of the world's H2 production is “Green”. Lack of regulations high production costs and inadequate infrastructure are significant impediments. The U.S. Department of Energy set a "111-target" which translates into $1/kg-H2 in the next decade. Many countries in the Middle East and North Africa (MENA) region have announced ambitious plans to produce green H2. Through techno-economic metrics and the impact of economies of scale this study investigates H2@Scale production. H2 Production Analysis and the System Advisor Model developed by the U.S. Department of Energy were used for analysis. The results demonstrate a significant decrease in the levelized cost of H2 (LCOH) when the production volume is scaled up. It was determined that the key cost drivers are capital cost energy installed balance of the plant and mechanical and electrical subsystems. The studied location is found promising for scaled production and developing its commodity status. The findings could serve as a benchmark for key stakeholders investors policymakers and the developer of relevant strategies in the infrastructure and H2 value chain.
An Estimation of Green Hydrogen Generation from Wind Energy: A Case Study from KSA
Sep 2023
Publication
Actually green hydrogen is viewed as a fundamental component in accelerating energy transition and empowering a sustainable future. The current study focuses on the estimation of green hydrogen generation by using wind energy via electrolysis in four sites located in Saudi Arabia. Results showed that the yearly amount of hydrogen that could be generated by using wind turbine ranges between 2542877 kg in Rafha and 3676925 kg in Dhahran. The hydrogen generated could be used to fuel vehicles and decrease the amount of GHG emission from vehicles in KSA. Also hydrogen may be used to store the excess of wind energy and to support the achievement of vision 2030 of the Kingdom. An economic assessment is carried out also in this paper. Results showed that the LCOH by using wind energy in KSA ranges from 2.82 $/kg to 3.81 $/kg.
Performance Assessment of a 25 kW Solid Oxide Cell Module for Hydrogen Production and Power Generation
Jan 2024
Publication
Hydrogen produced via water electrolysis from renewable electricity is considered a key energy carrier to defossilize hard-to-electrify sectors. Solid oxide cells (SOC) based reactors can supply hydrogen not only in electrolysis but also in fuel cell mode when operating with (synthetic) natural gas or biogas at low conversion (polygeneration mode). However the scale-up of SOC reactors to the multi-MW scale is still a research topic. Strategies for transient operation depending on electricity intermittency still need to be developed. In this work a unique testing environment for SOC reactors allows reversible operation demonstrating the successful switching between electrolysis (− 75 kW) and polygeneration (25 kW) modes. Transient and steady state experiments show promising performance with a net hydrogen production of 53 kg day− 1 in SOEL operation with ca. − 75 kW power input. The experimental results validate the scaling approach since the reactor shows homogenous temperature profiles.
Green Hydrogen: Resources Consumption, Technological Maturity, and Regulatory Framework
Aug 2023
Publication
Current climate crisis makes the need for reducing carbon emissions more than evident. For this reason renewable energy sources are expected to play a fundamental role. However these sources are not controllable but depend on the weather conditions. Therefore green hydrogen (hydrogen produced from water electrolysis using renewable energies) is emerging as the key energy carrier to solve this problem. Although different properties of hydrogen have been widely studied some key aspects such as the water and energy footprint as well as the technological development and the regulatory framework of green hydrogen in different parts of the world have not been analysed in depth. This work performs a data-driven analysis of these three pillars: water and energy footprint technological maturity and regulatory framework of green hydrogen technology. Results will allow the evaluation of green hydrogen deployment both the current situation and expectations. Regarding the water footprint this is lower than that of other fossil fuels and competitive with other types of hydrogen while the energy footprint is higher than that of other fuels. Additionally results show that technological and regulatory framework for hydrogen is not fully developed and there is a great inequality in green hydrogen legislation in different regions of the world.
A Systematic Study on Techno-Economic Evaluation of Hydrogen Production
Sep 2023
Publication
This paper aims to perform a systematic review with a bibliometric approach of the technoeconomic evaluation studies of hydrogen production. To achieve this objective a comprehensive outline of hydrogen production processes from fossil and renewable sources is presented. The results reveal that electrolysis classified as water splitting is the most investigated process in the literature since it contributes to a reduction in greenhouse gas emissions and presents other advantages such as maturity and applicability energy efficiency flexibility and energy storage potential. In addition the processes of gasification classified as thermochemical and steam reforming classified as catalytic reforming are worth mentioning. Regarding the biological category there is a balance between research on photo fermentation and dark fermentation. The literature on the techno-economic evaluation of hydrogen production highlights significant gaps including a scarcity of comprehensive studies a lack of emphasis on commercial viability an absence of sensitivity analysis and the need for comparative analyses between production technologies.
No more items...