Safety

Ignition conditions and risks of ignition on a permissible value of hydrogen concentration in purge gas prescribed by HFCV-GTR were reevaluated. Experiments were conducted to investigate burning behavior and thermal influence of continuous evacuation of hydrogen under continuous purge of air / hydrogen premixed gas which is close to an actual purge condition of FCV and thermal evacuation of hydrogen. As a result of the re-evaluation it was shown from the viewpoint of safety that the permissible value of hydrogen concentration in purge gas prescribed by the current HFCV GTR is appropriate.

The NREL Sensor Laboratory has been developing an analyzer that can verify compliance to the international United Nations Global Technical Regulation number 13 (GTR 13--Global Technical Regulation on Hydrogen and Fuel Cell Vehicles) prescriptive requirements pertaining to allowable hydrogen levels in the exhaust of fuel cell electric vehicles (FCEV) [1]. GTR 13 prescribes that the FCEV exhaust shall remain below 4 vol% H2 over a 3-second moving average and shall not at any time exceed 8 vol% H2 as verified with an analyzer with a response time (t90) of 300 ms or faster. GTR 13 has been implemented and is to serve as the basis for national regulations pertaining to hydrogen powered vehicle safety in the United States Canada Japan and the European Union. In the U.S. vehicle safety is overseen by the Department of Transportation (DOT) through the Federal Motor Vehicle Safety Standards (FMVSS) and in Canada by Transport Canada through the Canadian Motor Vehicle Safety Standard (CMVSS). The NREL FCEV exhaust analyzer is based upon a low-cost commercial hydrogen sensor with a response time (t90) of less than 250 ms. A prototype analyzer and gas probe assembly have been constructed and tested that can interface to the gas sampling system used by Environment and Climate Change Canada’s (ECCC) Emission Research and Measurement Section (ERMS) for the exhaust gas analysis. Through a partnership with Transport Canada ECCC will analyze the hydrogen level in the exhaust of a commercial FCEV. ECCC will use the NREL FCEV Exhaust Gas analyzer to perform these measurements. The analyzer was demonstrated on a FCEV operating under simulated road conditions using a chassis dynamometer at a private facility.

Hydrogen is a valuable option of clean fuel to keep the global temperature rise below 2°C. However one of the main barriers in its transport and use is to ensure safety levels that are comparable with traditional fuels. In particular liquid hydrogen accidents may not be fully understood (yet) and excluded by relevant risk assessment. For instance as hydrogen is cryogenically liquefied to increase its energy density during transport Boiling Liquid Expanding Vapor Explosions (BLEVE) is a potential and critical event that is important addressing in the hazard identification phase. Two past BLEVE accidents involving liquid hydrogen support such thesis. For this reason results from consequence analysis of hydrogen BLEVE will not only improve the understanding of the related physical phenomenon but also influence future risk assessment studies. This study aims to show the extent of consequence analysis influence on overall quantitative risk assessment of hydrogen technologies and propose a systematic approach for integration of overall results. The Dynamic Procedure for Atypical Scenario Identification (DyPASI) is used for this purpose. The work specifically focuses on consequence models that are originally developed for other substances and adapted for liquid hydrogen. Particular attention is given to the parameters affecting the magnitude of the accident as currently investigated by a number of research projects on hydrogen safety worldwide. A representative example of consequence analysis for liquid hydrogen release is employed in this study. Critical conditions detected by the numerical simulation models are accurately identified and considered for subsequent update of the overall system risk assessment.

When charging most types of industrial lead-acid batteries hydrogen gas is emitted. A large number of batteries especially in relatively small areas/enclosures and in the absence of an adequate ventilation system may create an explosion hazard. This paper describes full scale tests in confined space which demonstrate conditions that can occur in a battery room in the event of a ventilation system breakdown. Over the course of the tests full scale hydrogen emission experiments were performed to study emission time and flammable cloud formation according to the assumed emission velocity. On this basis the characteristics of dispersion of hydrogen in the battery room were obtained. The CFD model Fire Dynamic Simulator (NIST) was used for confirmation that the lack of ventilation in a battery room can be the cause of an explosive atmosphere developing and leading to a potential huge explosive hazard. It was demonstrated that different ventilation systems provide battery rooms with varying efficiencies of hydrogen removal. The most effective type appeared to be natural ventilation which proved more effective than mechanical means.

Safe practices in the production storage distribution and use of hydrogen are essential for the widespread acceptance of hydrogen and fuel cell technologies. A significant safety incident in any project could damage public perception of hydrogen and fuel cells. A recent incident involving a hydrogen mobile storage trailer in the United States has brought attention to the potential impacts of mobile hydrogen storage and transport. Road transport of bulk hydrogen presents unique hazards that can be very different from those for stationary equipment and new equipment developers may have less experience and expertise than seasoned gas providers. In response to the aforementioned incident and in support of hydrogen and fuel cell activities in California the Hydrogen Safety Panel (HSP) has investigated the safety of mobile hydrogen and fuel cell applications (mobile auxiliary/emergency fuel cell power units mobile fuellers multi-cylinder trailer transport unmanned aircraft power supplies and mobile hydrogen generators). The HSP examined the applications requirements and performance of mobile applications that are being used extensively outside of California to understand how safety considerations are applied. This paper discusses the results of the HSP’s evaluation of hydrogen and fuel cell mobile applications along with recommendations to address relevant safety issues.

This paper provides a detailed technical description of the United Nations Global Technical Regulation No. 13 (UN GTR #13) 1998 Agreement and contracting party obligations phase 2 activity and safety provisions being discussed and developed for heavy duty hydrogen fuel cell vehicles.

Portable H2 sensor was made by using mass spectrometer for the outside monitoring experiment: the leak test the replacement test of gas pipe line the combustion test the explosion experiment the H2 diffusion experiment and the recent issue of the exhaust gas of Fuel Cell Vehicle. In order to check the real time concentration of H2 in various conditions even in the highly humid condition the system volume of the sampling route was minimized with attaching the humidifier. Also to calibrate H2 concentration automatically the specific concentration H2 small cylinder was mounted in the system. In the experiment when H2 gas was introduced in the N2 flow or air in the tube or the high-pressure bottle highly concentrated H2 phases were observed by this sensor without diffusion. This H2 sensor can provide the real time information of the hydrogen molecules and the clouds. The basic characterization of this sensor showed 0-100% H2 concentrations within 2ms. Our observation showed the size of the high concentration phase of H2 and the low concentration phase after mixing process. The mixed and unmixed H2 unintended concentration of cloud gas the high speed small cluster of hydrogen molecules in purged gas were explored by this real time monitoring system.

We at Kawasaki have proposed a “CO2 free H2 chain” using the abundant brown coal of Australia as a hydrogen source. We developed the basic design package and finished the Front End Engineering Design (FEED) in 2014. There are not only the hazards of the processing plant system but also the characteristic hazards of a hydrogen plant system. We considered and carried out Hazard Identification (HAZID) as the most appropriate approach for safety design in this stage. This paper describes the safety design and HAZID which we practiced for the CO2-Free Hydrogen Supply Chain FEED.

We conducted a fuelling test with hydrogen gas for a safety evaluation of the nozzle/receptacle at a controlled temperature and humidity. Test results confirmed that the nozzle/receptacle froze under specific conditions. However freezing did not cause apparatus damage nor hydrogen leakage. The nozzle/receptacle is thus able to fuel safely even if the nozzle/receptacle is stuck due to ice. In addition we quantified the water volume that causes freezing.

This study presents a methodology of a quantitative risk assessment for the scenario of an onboard hydrogen storage tank rupture and tunnel fire incident. The application of the methodology is demonstrated on a road tunnel. The consequence analysis is carried out for the rupture of a 70 MPa 62.4-litre hydrogen storage tank in a fire that has a thermally activated pressure relief device (TPRD) failed or blocked during an incident. Scenarios with two states of charge (SoC) of the tank i.e. SoC = 99% and SoC = 59% are investigated. The risks in terms of fatalities per vehicle per year and the cost per incident are assessed. It is found that for the reduction in the risk with the hydrogen-powered vehicle in a road tunnel fire incident to the acceptable level of 10−5 fatality/vehicle/year the fireresistance rating (FRR) of the hydrogen storage tank should exceed 84 min. The FRR increase to this level reduces the societal risk to an acceptable level. The increase in the FRR to 91 min reduces the risk in terms of the cost of the incident to GBP 300 following the threshold cost of minor injury published by the UK Health and Safety Executive. The Frequency–Number (F–N) of the fatalities curve is developed to demonstrate the effect of mitigation measures on the risk reduction to socially acceptable levels. The performed sensitivity study confirms that with the broad range of input parameters including the fire brigade response time the risk of rupture of standard hydrogen tank-TPRD systems inside the road tunnel is unacceptable. One of the solutions enabling an inherently safer use of hydrogen-powered vehicles in tunnels is the implementation of breakthrough safety technology—the explosion free in a fire self-venting (TPRD-less) tanks.

The NREL Hydrogen Sensor Laboratory was commissioned in 2010 as a resource for the national and international hydrogen community to ensure the availability and proper use of hydrogen sensors. Since then the Sensor Laboratory has provided unbiased verification of hydrogen sensor performance for sensor developers end-users and regulatory agencies and has also provided active support for numerous code and standards development organizations. Although sensor performance assessment remains a core capability the mission of the NREL Sensor Laboratory has expanded toward a more holistic approach regarding the role of hydrogen detection and its implementation strategy for both assurance of facility safety and for process control applications. Active monitoring for detection of unintended releases has been identified as a viable approach for improving facility safety and lowering setbacks. The current research program for the Sensor Laboratory addresses both conventional and advanced developing detection strategies in response to the emerging large-scale hydrogen markets such as those envisioned by H2@Scale. These emerging hydrogen applications may require alternative detection strategies that supplement and may ultimately supplant the use of traditional sensors for monitoring hydrogen releases. Research focus areas for the NREL Sensor Laboratory now encompass the characterization of released hydrogen behavior to optimize detection strategies for both indoor and outdoor applications assess advanced methods of hydrogen leak detection such as hydrogen wide area monitoring for large scale applications implement active monitoring as a risk reduction strategy to improve safety at hydrogen facilities and to provide continuing support of hydrogen safety codes and standards. In addition to assurance of safety detection will be critical for process control applications such as hydrogen fuel quality verification for fuel cell vehicle applications and for monitoring and controlling of hydrogen-natural gas blend composition.

A series of more than 100 experiments with hydrogen-air mixtures at cryogenic temperatures have been performed in a shock tube in the frame of the PRESLHY project. A wide range of hydrogen concentrations from 8 to 60%H2 in the shock tube of the length of 5 m and 50 mm id was tested at cryogenic temperatures from 80 to 130K at ambient pressure. Flame propagation regimes were investigated for all hydrogen compositions in the shock tube at three different blockage ratios (BR) 0 0.3 and 0.6 as a function of initial temperature. Pressure sensors and InGaAs-photodiodes have been applied to monitor the flame and shock propagation velocity of the process. The experiments at ambient pressure and temperature were conducted as the reference data for cryogenic experiments. A critical expansion ratio for an effective flame acceleration to the speed of sound was experimentally found at cryogenic temperatures. The detonability criterion for smooth and obstructed channels was used to evaluate the detonation cell sizes at cryogenic temperatures as well. The main peculiarities of cryogenic combustion with respect to the safety assessment were that the maximum combustion pressure was several times higher compared to ambient temperature and the run-up-distance to detonation was several times shorter independent of lower chemical reactivity at cryogenic conditions.

This paper presents a series of experiments on the effectiveness of existing mechanical ventilation systems during accidental hydrogen releases in confined spaces like underground garages. The purpose was to find the mass flow rate limit hence the TPRD diameter limit that will not require a change in the ventilation system. The experiments were performed in a 40 ft ISO container in Norway and hydrogen gas was used in all experiments. The forced ventilation system was installed with a standard outlet 315 mm diameter. The ventilation parameters during the investigation were British Standard with 10 ACH and British Standard with 6 ACH. The hydrogen releases were obtained through 0.5 mm and 1 mm nozzle from different hydrogen reservoir pressures. Both types of mass flow: constant and blowdown were included in the experimental matrix. The analysis of hydrogen concentration of created hydrogen cloud in the container shows the influence of the forced ventilation on hydrogen releases together with TPRD diameter and reservoir pressure. The generated experimental data will be used to validate a CFD model in the next step.

Hydrogen is a renewable energy source with various features clean carbon-free high energy density which is being recognized internationally as a “future energy.” The US the EU Japan South Korea China and other countries or regions are gradually clarifying the development position of hydrogen. The rapid development of the hydrogen energy industry requires more hydrogenation infrastructure to meet the hydrogenation need of hydrogen fuel cell vehicles. Nevertheless due to the frequent occurrence of hydrogen infrastructure accidents their safety has become an obstacle to large-scale construction. This paper analyzed five sizes (diameters of 0.068 mm 0.215 mm 0.68 mm 2.15 mm and 6.8 mm) of hydrogen leakage in the hydrogen fueling station using Quantitative Risk Assessment (QRA) and HyRAM software. The results show that unignited leaks occur most frequently; leaks caused by flanges valves instruments compressors and filters occur more frequently; and the risk indicator of thermal radiation accident and structure collapse accident caused by over-pressure exceeds the Chinese individual acceptable risk standard and the risk indicator of a thermal radiation accident and head impact accident caused by overpressure is below the Chinese standard. On the other hand we simulated the consequences of hydrogen leak from the 45 MPa hydrogen storage vessels by the physic module of HyRAM and obtained the ranges of plume dispersion jet fire radiative heat flux and unconfined overpressure. We suggest targeted preventive measures and safety distance to provide references for hydrogen fueling stations’ safe construction and operation.

Efficient storage of hydrogen is crucial for the success of hydrogen energy markets. Hydrogen can be stored either as a compressed gas a refrigerated liquefied gas a cryo-compressed gas or in hydrides. This paper gives an overview of compressed hydrogen storage technologies focusing on high pressure storage tanks in metal and in composite materials. It details specific issues and constraints related to the materials and structure behavior in hydrogen and conditions representative of hydrogen energy uses. This paper is an update of the 2019 version that was presented in Australia. It especially covers recent progress made regarding regulations codes and standards for the design manufacturing periodic inspection and plastic materials’ evaluation of compressed hydrogen storage.

The use of hydrogen storage tanks at 100% of nominal working pressure NWP is expected only after refuelling. Driving between refuellings is characterised by the state of charge SoC<100%. There is experimental evidence that Type IV tanks tested in a fire at initial pressures below one-third of its NWP depending on a fire source were leaking without rupture. This paper aims at understanding this phenomenon and the development of a predictive model. The numerical research has demonstrated that the heat transfer from fire through the composite overwrap is sufficient to melt the polymer liner. This initiates hydrogen microleaks through the composite wall before it loses the load-bearing ability when the resin degrades deep enough to cause the tank to rupture. The dependence of tank fire-resistance rating (FRR) on the SoC is presented for tanks of volume in the range 36-244 L. The tank wall thickness non-uniformity i.e. thinner composite at the dome area is identified as a serious issue for tank’s fire resistance that must be addressed by tank manufacturers and OEMs. The effect of the burst pressure ratio on FRR is investigated. It is concluded that thermal parameters of the composite wall i.e. decomposition heat and temperatures play a vital role in simulations of tank failure and thus FRR.

This paper describes two models for analysing and simulating the physical effects of explosive phase transition of liquid hydrogen (LH2) also known as cold BLEVE. The present work is based on theoretical and experimental work for liquefied CO2. A Rankine Hugoniot analysis for evaporation waves that was previously developed for CO2 is now extended to LH2. A CFD-method for simulating two-phase flow with mass transfer between the phases is presented and compared with the Rankine Hugoniot analysis results. The Rankine Hugoniot method uses real fluid equations of state suited for LH2 while the CFD method uses linear equations of state suited for shock capturing methods. The results show that there will be a blast from a catastrophic rupture of an LH2 vessel and that the blast waves will experience a slow decay due to the large positive pressure phase.

Hydrogen which has a high energy density and does not emit pollutants is considered an alternative energy source to replace fossil fuels. Herein we report an experimental study on hydrogen leaks and ventilation methods for preventing damage caused by leaks from hydrogen fuel cell rooms in homes among various uses of hydrogen. This experiment was conducted in a temporary space with a volume of 11.484 m3 . The supplied pressure leak-hole size and leakage amount were adjusted as the experimental conditions. The resulting hydrogen concentrations which changed according to the operation of the ventilation openings ventilation fan and supplied shutoff valve were measured. The experimental results showed that the reductions in the hydrogen concentration due to the shutoff valve were the most significant. The maximum hydrogen concentration could be reduced by 80% or more if it is 100 times that of the leakage volume or higher. The shutoff valve ventilation fan and ventilation openings were required to reduce the concentrations of the fuel cell room hydrogen in a spatially uniform manner. Although the hydrogen concentration in a small hydrogen fuel cell room for home use can rapidly increase a rapid reduction in the concentration of hydrogen with an appropriate ventilation system has been experimentally proven.

On December 19 2017 a large balloon containing about 22 thousand cubic meters of hydrogen was deliberately torn open to initiate deflation at the completion of a filling test. An inadvertent ignition occurred after about two seconds and caused an explosion that produced extensive light damage to a large building near the balloon test pad. The analysis described here includes an estimate of the buoyancy induced mixing into the torn balloon and the blast wave produced by assumed constant flame speed combustion of the 55% to 65% hydrogen-in-air mixture. Comparisons of calculated blast wave pressures are consistent with estimates of the pressure needed to cause the observed building damage for flame speeds in the range 85 m/s to about 100 m/s.

Current safety codes and technical standards related to Japanese hydrogen refueling stations (HRSs) have been established based on qualitative risk assessment and quantitative effectiveness validation of safety measures for more than ten years. In the last decade there has been significant development in the technologies and significant increment in operational experience related to HRSs. We performed a quantitative risk assessment (QRA) of the HRS model representing Japanese HRSs with the latest information in the previous study. The QRA results were obtained by summing risk contours derived from each process unit. They showed that the risk contours of 10-3 and 10-4 per year were confined within the HRS boundaries whereas those of 10-5 and 10-6 per year are still present outside the HRS boundaries. Therefore we analyzed the summation of risk contours derived from each unit and identified the largest risk scenarios outside the station. The HRS model in the previous study did not consider fire and blast protection walls which could reduce the risks outside the station. Therefore we conducted a detailed risk analysis of the identified scenarios using 3D structure modeling. The heat radiation and temperature rise of jet fire scenarios that pose the greatest risk to the physical surroundings in the HRS model were estimated in detail based on computational fluid dynamics with 3D structures including fire protection walls. Results show that the risks spreading outside the north- west- and east-side station boundaries are expected to be acceptable by incorporating the fire protection wall into the Japanese HRS model.

Unstable hydrogen-air flame behavior randomities are important for industrial safety hydrogen infrastructure safety and nuclear power plant hydrogen safety problems. The paper is devoted to an experimental and theoretical study of the uncertainty in the acceleration of a premixed laminar unstable hydrogen flame. The results of experiments on spherical flame propagation in hydrogen-air mixtures with a hydrogen content of 10 to 60% are presented. The experiments were repeated up to 30 times in the same mixtures. A statistical analysis of the experimental results has been carried out. The scatter of the experimental data depending on the hydrogen content in the mixture was estimated. It was found to be between 8 to 17% for different mixtures with the same flame radius and mixture composition. Similar results were obtained using the numerical integration of the Sivashinsky equation of flame propagation.

Hydrogen gas storage place has been increasing daily because of its consumption. Hydrogen gas is a dream fuel of the future with many social economic and environmental benefits to its credit. However many hydrogen storage tanks exploded accidentally and significantly lost the economy infrastructure and living beings. In this study a protection wall under a worst-case scenario explosion of a hydrogen gas tank was analyzed with commercial software LS-DYNA. TNT equivalent method was used to calculate the weight of TNT for Hydrogen. Reinforced concrete and composite protection wall under TNT explosion was analyzed with a different distance of TNT. The initial dimension of the reinforced concrete protection wall was taken from the Korea gas safety code book (KGS FP217) and studied the various condition. H-beam was used to make the composite protection wall. Arbitrary-Lagrangian-Eulerian (ALE) simulation from LS-DYNA and ConWep pressure had a good agreement. Used of the composite structure had a minimum displacement than a normal reinforced concrete protection wall. During the worst-case scenario explosion of a hydrogen gas 300 kg storage tank the minimum distance between the hydrogen gas tank storage and protection wall should be 3.6 m.

Hydrogen as a clean fuel offers a practical pathway to achieve net-zero targets. However due to its physical and chemical characteristics there are some safety concerns for large-scale hydrogen utilisation particularly in process safety management. Leakage of gaseous hydrogen especially in semi-confined spaces such as tunnels can lead to catastrophic outcomes including uncontrolled fire and explosion. The current paper describes the outcome of an experimental and numerical study that aims to understand the dispersion of leaked light gas in a semi-confined space to support the adoption of hydrogen. A dispersion chamber with dimensions of 4m × 0.3m × 0.3m was constructed to investigate a baseline gas leakage scenario. To reduce the risk of the experiment in the laboratory helium is utilised as a surrogate for hydrogen. Computational fluid dynamics simulations are con ducted using FLACS-CFD to model the dispersion of leaked gas in different scenarios focusing on the impact of the ventilation velocity leakage rate and slope. The results from comprehensive numerical simulations show that ventilation is a critical safety management measure that can significantly reduce the growth of flammable clouds and mitigate the fire and explosion risk. Even with the lowest ventilation velocity of 0.25 m/s an improvement in the gas concentration level of 29.34% can be achieved in the downstream chamber. The current results will help to further enhance the understanding of hydrogen safety aspects.

The recent growth of the net of hydrogen fuelling stations increases the demands to transport compressed hydrogen on road by battery vehicles or tube-trailers both in composite pressure vessels. As a transport regulation the ADR is applicable in Europe and adjoined regions and is used for national transport in the EU. This regulation provides requirements based on the behaviour of each individual pressure vessel regardless of the pressure of the transported hydrogen and relevant consequences resulting from generally possible worst case scenarios such as sudden rupture. In 2012 the BAM (German Federal Institute for Materials Research and Testing) introduced consequence-dependent requirements and established them in national transport requirements concerning the “UN service life checks” etc. to consider the transported volume and pressure of gases. This results in a requirement that becomes more restrictive as the product of pressure and volume increases. In the studies presented here the safety measures for hydrogen road transport are identified and reviewed through a number of safety measures from countries including Japan the USA and China. Subsequently the failure consequences of using trailer vehicles the related risk and the chance are evaluated. A benefit-related risk criterion is suggested to add to regulations and to be defined as a safety goal in standards for hydrogen transport vehicles and for mounted pressure vessels. Finally an idea is given for generating probabilistic safety data and for highly efficient evaluation without a significant increase of effort.

The energy world is changing rapidly pushed also by the need for new green energy sources to reduce greenhouse gas emissions. The fast development of renewable energies has created many problems associated with grid management and stability which could be solved with storage systems. The hydrogen economy could be an answer to the need of storage systems and clean fuel for transportation. The Electrochemical Hydrogen Compressor (EHC) is an electrochemical device which could find a place in this scenario giving a solution for the hydrogen purification and compression for storage. This work analyzes through experimental and modeling studies the performance of the EHC in terms of polarization curve Hydrogen Recovery Factor (HRF) and outlet hydrogen purity. The influence of many input parameters such as the total inlet flow rate the hydrogen inlet concentration the contaminant in the feed and the cathode pressure have been investigated. Furthermore the EHC performance have been modelled in a 1D + 1D model implemented in Matlab® solving the Butler-Volmer system of equations numerically. The experimental campaign has shown that high purities can be obtained for the hydrogen separation from N2 and CH4 and purities over 98% feeding He. An increase in the cathode pressure has shown a slight improvement in the obtained purity. A comparison between PSA unit and EHC for a mixture 75% H2 – 25% CH4 at different outlet hydrogen pressure and purity was performed to analyze the energy consumption required. Results show PSA unit is convenient at large scale and high H2 concentration while for low concentration is extremely energy intense. The EHC proved to be worthwhile at small scale and higher outlet hydrogen pressure.