France
Water Photo-Electrooxidation Using Mats of TiO2 Nanorods, Surface Sensitized by a Metal–Organic Framework of Nickel and 1,2-Benzene Dicarboxylic Acid
Apr 2021
Publication
Photoanodes comprising a transparent glass substrate coated with a thin conductive film of fluorine-doped tin oxide (FTO) and a thin layer of a photoactive phase have been fabricated and tested with regard to the photo-electro-oxidation of water into molecular oxygen. The photoactive layer was made of a mat of TiO2 nanorods (TDNRs) of micrometric thickness. Individual nanorods were successfully photosensitized with nanoparticles of a metal–organic framework (MOF) of nickel and 12-benzene dicarboxylic acid (BDCA). Detailed microstructural information was obtained from SEM and TEM analysis. The chemical composition of the active layer was determined by XRD XPS and FTIR analysis. Optical properties were determined by UV–Vis spectroscopy. The water photooxidation activity was evaluated by linear sweep voltammetry and the robustness was assessed by chrono-amperometry. The OER (oxygen evolution reaction) photo-activity of these photoelectrodes was found to be directly related to the amount of MOF deposited on the TiO2 nanorods and was therefore maximized by adjusting the MOF content. The microscopic reaction mechanism which controls the photoactivity of these photoelectrodes was analyzed by photo-electrochemical impedance spectroscopy. Microscopic rate parameters are reported. These results contribute to the development and characterization of MOF-sensitized OER photoanodes.
An Evaluation of Turbocharging and Supercharging Options for High-Efficiency Fuel Cell Electric Vehicles
Dec 2018
Publication
Mass-produced off-the-shelf automotive air compressors cannot be directly used for boosting a fuel cell vehicle (FCV) application in the same way that they are used in internal combustion engines since the requirements are different. These include a high pressure ratio a low mass flow rate a high efficiency requirement and a compact size. From the established fuel cell types the most promising for application in passenger cars or light commercial vehicle applications is the proton exchange membrane fuel cell (PEMFC) operating at around 80 ◦C. In this case an electric-assisted turbocharger (E-turbocharger) and electric supercharger (single or two-stage) are more suitable than screw and scroll compressors. In order to determine which type of these boosting options is the most suitable for FCV application and assess their individual merits a co-simulation of FCV powertrains between GT-SUITE and MATLAB/SIMULINK is realised to compare vehicle performance on the Worldwide Harmonised Light Vehicle Test Procedure (WLTP) driving cycle. The results showed that the vehicle equipped with an E-turbocharger had higher performance than the vehicle equipped with a two-stage compressor in the aspects of electric system efficiency (+1.6%) and driving range (+3.7%); however for the same maximal output power the vehicle’s stack was 12.5% heavier and larger. Then due to the existence of the turbine the E-turbocharger led to higher performance than the single-stage compressor for the same stack size. The solid oxide fuel cell is also promising for transportation application especially for a use as range extender. The results show that a 24-kWh electric vehicle can increase its driving range by 252% due to a 5 kW solid oxide fuel cell (SOFC) stack and a gas turbine recovery system. The WLTP driving range depends on the charge cycle but with a pure hydrogen tank of 6.2 kg the vehicle can reach more than 600 km.
Optimization of Hydrogen Cost and Transport Technology in France and Germany for Various Production and Demand Scenarios
Jan 2021
Publication
Green hydrogen for mobility represents an alternative to conventional fuel to decarbonize the transportation sector. Nevertheless the thermodynamic properties make the transport and the storage of this energy carrier at standard conditions inefficient. Therefore this study deploys a georeferenced optimal transport infrastructure for four base case scenarios in France and Germany that differs by production distribution based on wind power potential and demand capacities for the mobility sector at different penetration shares for 2030 and 2050. The restrained transport network to the road infrastructure allows focusing on the optimum combination of trucks operating at different states of aggregations and storage technologies and its impact on the annual cost and hydrogen flow using linear programming. Furthermore four other scenarios with production cost investigate the impact of upstream supply chain cost and eight scenarios with daily transport and storage optimization analyse the modeling method sensitivity. The results show that compressed hydrogen gas at a high presser level around 500 bar was on average a better option. However at an early stage of hydrogen fuel penetration substituting compressed gas at low to medium pressure levels by liquid organic hydrogen carrier minimizes the transport and storage costs. Finally in France hydrogen production matches population distribution in contrast to Germany which suffers from supply and demand disparity.
Spherically Expanding Flame Simulations in Cantera Using a Lagrangian Formulation
Sep 2021
Publication
A Lagrangian-based one-dimensional approach has been developed using Cantera to study the dynamics of spherically expanding flames. The detailed reaction model USC-Mech II has been employed to examine flame propagating in hydrogen-air mixtures. In the first part our approach has been validated against laminar flame speed and Markstein number data from the literature. It was shown that the laminar flame speed was predicted within 5% on average but that discrepancies were observed for the Markstein number especially for rich mixtures. In the second part a detailed analysis of the thermo-chemical dynamics along the path of Lagrangian particles propagating in stretched flames was performed. For mixtures with negative Markstein lengths it was found that at high stretch rates the mixture entering the reaction-dominated period is less lean with respect to the initial mixture than at low stretch rate. This induces a faster rate of chemical heat release and of active radical production which results in a higher flame propagation speed. Opposite effects were observed for mixtures with positive Markstein lengths for which slower flame propagation was observed at high stretch rates compared to low stretch rates."
Multi-Objective Optimization-Based Health-Conscious Predictive Energy Management Strategy for Fuel Cell Hybrid Electric Vehicles
Feb 2022
Publication
The Energy Management Strategy (EMS) in Fuel Cell Hybrid Electric Vehicles (FCHEVs) is the key part to enhance optimal power distribution. Indeed the most recent works are focusing on optimizing hydrogen consumption without taking into consideration the degradation of embedded energy sources. In order to overcome this lack of knowledge this paper describes a new health-conscious EMS algorithm based on Model Predictive Control (MPC) which aims to minimize the battery degradation to extend its lifetime. In this proposed algorithm the health-conscious EMS is normalized in order to address its multi-objective optimization. Then weighting factors are assigned in the objective function to minimize the selected criteria. Compared to most EMSs based on optimization techniques this proposed approach does not require any information about the speed profile which allows it to be used for real-time control of FCHEV. The achieved simulation results show that the proposed approach reduces the economic cost up to 50% for some speed profile keeping the battery pack in a safe range and significantly reducing energy sources degradation. The proposed health-conscious EMS has been validated experimentally and its online operation ability clearly highlighted on a PEMFC delivery postal vehicle.
An Overview of the Recent Advances in Composite Materials and Artificial Intelligence for Hydrogen Storage Vessels Design
Mar 2023
Publication
The environmental impact of CO2 emissions is widely acknowledged making the development of alternative propulsion systems a priority. Hydrogen is a potential candidate to replace fossil fuels for transport applications with three technologies considered for the onboard storage of hydrogen: storage in the form of a compressed gas storage as a cryogenic liquid and storage as a solid. These technologies are now competing to meet the requirements of vehicle manufacturers; each has its own unique challenges that must be understood to direct future research and development efforts. This paper reviews technological developments for Hydrogen Storage Vessel (HSV) designs including their technical performance manufacturing costs safety and environmental impact. More specifically an up-to-date review of fiber-reinforced polymer composite HSVs was explored including the end-of-life recycling options. A review of current numerical models for HSVs was conducted including the use of artificial intelligence techniques to assess the performance of composite HSVs leading to more sophisticated designs for achieving a more sustainable future.
Optimization of a Hydrogen-based Hybrid Propulsion System Under Aircraft Performance Constraints
Aug 2021
Publication
This paper addresses the topic of the conceptual design of a regional aircraft with hybrid electric propulsion based on hydrogen fuel cells. It aims at providing an optimization-based method to design a hybrid propulsive system comprising two power sources (jet fuel and hydrogen) for the generation of the required propulsive power and at studying the impact of fuel cell technologies on the aircraft performances. Indeed by performing optimizations for two hybrid propulsive systems using either low temperature or high temperature Proton-exchange membrane fuel cells this study provides a preliminary assessment of the impact of the fuel cell operating temperature on the system design and the overall aircraft performance. First this paper gives a description of the baseline turboprop regional aircraft with a focus on its high speed and low speed flight performances which will serve as requirements for the design of the hybrid aircraft. Then the hybrid electric architecture and the sizing models of the propulsion system are presented. Finally optimizations are performed to design two parallel hybrid propulsive systems based on different fuel cells technologies and aimed at minimizing the block fuel per passenger over a mission of 200 nm. Results show how the proposed methodology and models lead to design two propulsive systems capable of reducing the fuel consumption per passenger by more than 30% compared to the baseline aircraft. The study also shows that the choice of fuel cell operating temperature has a first-order impact on the total mass of the propulsive system due to the higher cooling requirement of the low temperature fuel cells.
Complex Metal Borohydrides: From Laboratory Oddities to Prime Candidates in Energy Storage Applications
Mar 2022
Publication
Despite being the lightest element in the periodic table hydrogen poses many risks regarding its production storage and transport but it is also the one element promising pollutionfree energy for the planet energy reliability and sustainability. Development of such novel materials conveying a hydrogen source face stringent scrutiny from both a scientific and a safety point of view: they are required to have a high hydrogen wt.% storage capacity must store hydrogen in a safe manner (i.e. by chemically binding it) and should exhibit controlled and preferably rapid absorption–desorption kinetics. Even the most advanced composites today face the difficult task of overcoming the harsh re-hydrogenation conditions (elevated temperature high hydrogen pressure). Traditionally the most utilized materials have been RMH (reactive metal hydrides) and complex metal borohydrides M(BH4 )x (M: main group or transition metal; x: valence of M) often along with metal amides or various additives serving as catalysts (Pd2+ Ti4+ etc.). Through destabilization (kinetic or thermodynamic) M(BH4 )x can effectively lower their dehydrogenation enthalpy providing for a faster reaction occurring at a lower temperature onset. The present review summarizes the recent scientific results on various metal borohydrides aiming to present the current state-of-the-art on such hydrogen storage materials while trying to analyze the pros and cons of each material regarding its thermodynamic and kinetic behavior in hydrogenation studies.
Global Hydrogen Review 2023
Sep 2023
Publication
The Global Hydrogen Review is an annual publication by the International Energy Agency that tracks hydrogen production and demand worldwide as well as progress in critical areas such as infrastructure development trade policy regulation investments and innovation. The report is an output of the Clean Energy Ministerial Hydrogen Initiative and is intended to inform energy sector stakeholders on the status and future prospects of hydrogen while also informing discussions at the Hydrogen Energy Ministerial Meeting organised by Japan. Focusing on hydrogen’s potentially major role in meeting international energy and climate goals the Review aims to help decision makers fine-tune strategies to attract investment and facilitate deployment of hydrogen technologies at the same time as creating demand for hydrogen and hydrogen-based fuels. It compares real-world developments with the stated ambitions of government and industry. This year’s report includes a focus on demand creation for low-emission hydrogen. Global hydrogen use is increasing but demand remains so far concentrated in traditional uses in refining and the chemical industry and mostly met by hydrogen produced from unabated fossil fuels. To meet climate ambitions there is an urgent need to switch hydrogen use in existing applications to low-emission hydrogen and to expand use to new applications in heavy industry or long-distance transport.
CFD Simulation of a Hybrid Solar/Electric Reactor for Hydrogen and Carbon Production from Methane Cracking
Jan 2023
Publication
Methane pyrolysis is a transitional technology for environmentally benign hydrogen production with zero greenhouse gas emissions especially when concentrated solar energy is the heating source for supplying high-temperature process heat. This study is focused on solar methane pyrolysis as an attractive decarbonization process to produce both hydrogen gas and solid carbon with zero CO2 emissions. Direct normal irradiance (DNI) variations arising from inherent solar resource variability (clouds fog day-night cycle etc.) generally hinder continuity and stability of the solar process. Therefore a novel hybrid solar/electric reactor was designed at PROMES-CNRS laboratory to cope with DNI variations. Such a design features electric heating when the DNI is low and can potentially boost the thermochemical performance of the process when coupled solar/electric heating is applied thanks to an enlarged heated zone. Computational fluid dynamics (CFD) simulations through ANSYS Fluent were performed to investigate the performance of this reactor under different operating conditions. More particularly the influence of various process parameters including temperature gas residence time methane dilution and hybridization on the methane conversion was assessed. The model combined fluid flow hydrodynamics and heat and mass transfer coupled with gas-phase pyrolysis reactions. Increasing the heating temperature was found to boost methane conversion (91% at 1473 K against ~100% at 1573 K for a coupled solar-electric heating). The increase of inlet gas flow rate Q0 lowered methane conversion since it affected the gas space-time (91% at Q0 = 0.42 NL/min vs. 67% at Q0 = 0.84 NL/min). A coupled heating also resulted in significantly better performance than with only electric heating because it broadened the hot zone (91% vs. 75% methane conversion for coupled heating and only electric heating respectively). The model was further validated with experimental results of methane pyrolysis. This study demonstrates the potential of the hybrid reactor for solar-driven methane pyrolysis as a promising route toward clean hydrogen and carbon production and further highlights the role of key parameters to improve the process performance.
Techno-economic Feasibility of Hybrid PV/wind/battery/thermal Storage Trigeneration System: Toward 100% Energy Independency and Green Hydrogen Production
Dec 2022
Publication
With the clear adverse impacts of fossil fuel-based energy systems on the climate and environment ever-growing interest and rapid developments are taking place toward full or nearly full dependence on renewable energies in the next few decades. Estonia is a European country with large demands for electricity and thermal energy for district heating. Considering it as the case study this work explores the feasibility and full potential of optimally sized photovoltaic (PV) wind and PV/wind systems equipped with electric and thermal storage to fulfill those demands. Given the large excess energy from 100% renewable energy systems for an entire country this excess is utilized to first meet the district heating demand and then to produce hydrogen fuel. Using simplified models for PV and wind systems and considering polymer electrolyte membrane (PEM) electrolysis a genetic optimizer is employed for scanning Estonia for optimal installation sites of the three systems that maximize the fulfillment of the demand and the supply–demand matching while minimizing the cost of energy. The results demonstrate the feasibility of all systems fully covering the two demands while making a profit compared to selling the excess produced electricity directly. However the PV-driven system showed enormous required system capacity and amounts of excess energy with the limited solar resources in Estonia. The wind system showed relatively closer characteristics to the hybrid system but required a higher storage capacity by 75.77%. The hybrid PV/wind-driven system required a total capacity of 194 GW most of which belong to the wind system. It was also superior concerning the amount (15.05 × 109 tons) and cost (1.42 USD/kg) of the produced green hydrogen. With such full mapping of the installation capacities and techno-economic parameters of the three systems across the country this study can assist policymakers when planning different country-scale cogeneration systems.
Society, Materials, and the Environment: The Case of Steel
Mar 2020
Publication
This paper reviews the relationship between the production of steel and the environment as it stands today. It deals with raw material issues (availability scarcity) energy resources and generation of by-products i.e. the circular economy the anthropogenic iron mine and the energy transition. The paper also deals with emissions to air (dust Particulate Matter heavy metals Persistant Organics Pollutants) water and soil i.e. with toxicity ecotoxicity epidemiology and health issues but also greenhouse gas emissions i.e. climate change. The loss of biodiversity is also mentioned. All these topics are analyzed with historical hindsight and the present understanding of their physics and chemistry is discussed stressing areas where knowledge is still lacking. In the face of all these issues technological solutions were sought to alleviate their effects: many areas are presently satisfactorily handled (the circular economy—a historical’ practice in the case of steel energy conservation air/water/soil emissions) and in line with present environmental regulations; on the other hand there are important hanging issues such as the generation of mine tailings (and tailings dam failures) the emissions of greenhouse gases (the steel industry plans to become carbon-neutral by 2050 at least in the EU) and the emission of fine PM which WHO correlates with premature deaths. Moreover present regulatory levels of emissions will necessarily become much stricter.
Fast Sizing Methodology and Assessment of Energy Storage Configuration on the Flight Time of a Multirotor Aerial Vehicle
Apr 2023
Publication
Urban air mobility (UAM) defined as safe and efficient air traffic operations in a metropolitan area for manned aircraft and unmanned aircraft systems is being researched and developed by industry academia and government. This kind of mobility offers an opportunity to construct a green and sustainable sub-sector building upon the lessons learned over decades by aviation. Thanks to their non-polluting operation and simple air traffic management electric vertical take-off and landing (eVTOL) aircraft technologies are currently being developed and experimented with for this purpose. However to successfully complete the certification and commercialization stage several challenges need to be overcome particularly in terms of performance such as flight time and endurance and reliability. In this paper a fast methodology for sizing and selecting the propulsion chain components of an eVTOL multirotor aerial vehicle was developed and validated on a reduced-scale prototype of an electric multirotor vehicle with a GTOW of 15 kg. This methodology is associated with a comparative study of energy storage system configurations in order to assess their effect on the flight time of the aerial vehicle. First the optimal pair motor/propeller was selected using a global nonlinear optimization in order to maximize the specific efficiency of these components. Second five energy storage technologies were sized in order to evaluate their influence on the aerial vehicle flight time. Finally based on this sizing process the optimized propulsion chain gross take-off weight (GTOW) was evaluated for each energy storage configuration using regression-based methods based on propulsion chain supplier data.
Alternative and Innovative Solid Oxide Electrolysis Cell Materials: A Short Review
Jun 2021
Publication
Solid oxide electrolysis cell is the leading technology for production of green hydrogen by high temperature electrolysis. However optimization of existing reference materials constituting the cell and development of innovative materials remain critical for solid oxide electrolysis cell. In particular they are key to reach performance and durability targets compatible with a commercialization for the three main markets identified as follows: large-scale H2 production Power-to-X and Power-to-Power. This short review summarizes the latest progress in research and development of alternative and innovative materials for solid oxide electrolysis cells with a main focus on cathode-supported cell materials. A brief description of the layers constituting the solid oxide electrolysis cell is provided with the associated current state-of-the-art materials. A further emphasis on the most promising alternative and innovative materials for each layer follows based on the major aspects from an industrial perspective to reach a competitive hydrogen production cost for the main targeted markets: performance durability scaling up/manufacturing ability and operational flexibility.
The Role of Hydrogen for Deep Decarbonization of Energy Systems: A Chilean Case Study
Mar 2023
Publication
In this paper we implement a long-term multi-sectoral energy planning model to evaluate the role of green hydrogen in the energy mix of Chile a country with a high renewable potential under stringent emission reduction objectives in 2050. Our results show that green hydrogen is a cost-effective and environmentally friendly route especially for hard-to-abate sectors such as interprovincial and freight transport. They also suggest a strong synergy of hydrogen with electricity generation from renewable sources. Our numerical simulations show that Chile should (i) start immediately to develop hydrogen production through electrolyzers all along the country (ii) keep investing in wind and solar generation capacities ensuring a low cost hydrogen production and reinforce the power transmission grid to allow nodal hydrogen production (iii) foster the use of electric mobility for cars and local buses and of hydrogen for long-haul trucks and interprovincial buses and (iv) develop seasonal hydrogen storage and hydrogen cells to be exploited for electricity supply especially for the most stringent emission reduction objectives.
Hydrogenization of Underground Storage of Natural Gas
Aug 2015
Publication
The intermittent production of the renewable energy imposes the necessity to temporarily store it. Large amounts of exceeding electricity can be stored in geological strata in the form of hydrogen. The conversion of hydrogen to electricity and vice versa can be performed in electrolyzers and fuel elements by chemical methods. The nowadays technical solution accepted by the European industry consists of injecting small concentrations of hydrogen in the existing storages of natural gas. The progressive development of this technology will finally lead to the creation of underground storages of pure hydrogen. Due to the low viscosity and low density of hydrogen it is expected that the problem of an unstable displacement including viscous fingering and gravity overriding will be more pronounced. Additionally the injection of hydrogen in geological strata could encounter chemical reactivity induced by various species of microorganisms that consume hydrogen for their metabolism. One of the products of such reactions is methane produced from Sabatier reaction between H2 and CO2. Other hydrogenotrophic reactions could be caused by acetogenic archaea sulfate-reducing bacteria and iron-reducing bacteria. In the present paper a mathematical model is presented which is capable to reflect the coupled hydrodynamic and bio-chemical processes in UHS. The model has been numerically implemented by using the open source code DuMuX developed by the University of Stuttgart. The obtained bio-chemical version of DuMuX was used to model the evolution of a hypothetical underground storage of hydrogen. We have revealed that the behavior of an underground hydrogen storage is different than that of a natural gas storage. Both the hydrodynamic and the bio-chemical effects contribute to the different characteristics.
A Comprehensive Survey of Alkaline Electrolyzer Modeling: Electrical Domain and Specific Electrolyte Conductivity
May 2022
Publication
Alkaline electrolyzers are the most widespread technology due to their maturity low cost and large capacity in generating hydrogen. However compared to proton exchange membrane (PEM) electrolyzers they request the use of potassium hydroxide (KOH) or sodium hydroxide (NaOH) since the electrolyte relies on a liquid solution. For this reason the performances of alkaline electrolyzers are governed by the electrolyte concentration and operating temperature. Due to the growing development of the water electrolysis process based on alkaline electrolyzers to generate green hydrogen from renewable energy sources the main purpose of this paper is to carry out a comprehensive survey on alkaline electrolyzers and more specifically about their electrical domain and specific electrolytic conductivity. Besides this survey will allow emphasizing the remaining key issues from the modeling point of view.
AC-DC Converters for Electrolyzer Applications: State of the Art and Future Challenges
May 2020
Publication
The main objective of the article is to provide a thorough review of currently used AC-DC converters for alkaline and proton exchange membrane (PEM) electrolyzers in power grid or wind energy conversion systems. Based on the current literature this article aims at emphasizing the advantages and drawbacks of AC-DC converters mainly based on thyristor rectifier bridges and chopper-rectifiers. The analysis is mainly focused on the current issues for these converters in terms of specific energy consumption current ripple reliability efficiency and power quality. From this analysis it is shown that thyristors-based rectifiers are particularly fit for high-power applications but require the use of active and passive filters to enhance the power quality. By comparison the association combination of the chopper-rectifier can avoid the use of bulky active and passive filters since it can improve power quality. However the use of a basic chopper (i.e. buck converter) presents several disadvantages from the reliability energy efficiency voltage ratio and current ripple point of view. For this reason new emerging DC-DC converters must be employed to meet these important issues according to the availability of new power switching devices. Finally based on the authors’ experience in power conversion for PEM electrolyzers a discussion is provided regarding the future challenges that must face power electronics for green hydrogen production based on renewable energy sources.
Water Electrolysis: From Textbook Knowledge to the Latest Scientific Strategies and Industrial Developments
May 2022
Publication
Replacing fossil fuels with energy sources and carriers that are sustainable environmentally benign and affordable is amongst the most pressing challenges for future socio-economic development. To that goal hydrogen is presumed to be the most promising energy carrier. Electrocatalytic water splitting if driven by green electricity would provide hydrogen with minimal CO2 footprint. The viability of water electrolysis still hinges on the availability of durable earth-abundant electrocatalyst materials and the overall process efficiency. This review spans from the fundamentals of electrocatalytically initiated water splitting to the very latest scientific findings from university and institutional research also covering specifications and special features of the current industrial processes and those processes currently being tested in large-scale applications. Recently developed strategies are described for the optimisation and discovery of active and durable materials for electrodes that ever-increasingly harness first principles calculations and machine learning. In addition a technoeconomic analysis of water electrolysis is included that allows an assessment of the extent to which a large-scale implementation of water splitting can help to combat climate change. This review article is intended to cross-pollinate and strengthen efforts from fundamental understanding to technical implementation and to improve the ‘junctions’ between the field’s physical chemists materials scientists and engineers as well as stimulate much-needed exchange among these groups on challenges encountered in the different domains.
Blowout Prediction on a Salt Cavern Selected for a Hydrogen Storage Pilot
Oct 2022
Publication
To prevent climate change Europe and the world must shift to low-carbon and renewable energies. Hydrogen as an energy vector provides viable solutions for replacing polluting and carbon-emitting fossil fuels. Gaseous hydrogen can be stored underground and coupled with existing natural gas pipe networks. Salt cavern storage is the best suited technology to meet the challenges of new energy systems. Hydrogen storage caverns are currently operated in the UK and Texas. A preliminary risk analysis dedicated to underground hydrogen salt caverns highlighted the importance of containment losses (leaks) and the formation of gas clouds following blowouts whose ignition may generate dangerous phenomena such as jet fires unconfined vapor cloud explosions (UVCEs) or flashfires. A blowout is not a frequent accident in gas storage caverns. A safety valve is often set at a 30 m depth below ground level; it is automatically triggered following a pressure drop at the wellhead. Nevertheless a blowout remains to be one of the significant accidental scenarios likely to occur during hydrogen underground storage in salt caverns. In this paper we present modelling the subterraneous and aerial parts of a blowout on an EZ53 salt cavern fully filled with hydrogen.
A Review of the MSCA ITN ECOSTORE—Novel Complex Metal Hydrides for Efficient and Compact Storage of Renewable Energy as Hydrogen and Electricity
Mar 2020
Publication
Hydrogen as an energy carrier is very versatile in energy storage applications. Developments in novel sustainable technologies towards a CO2-free society are needed and the exploration of all-solid-state batteries (ASSBs) as well as solid-state hydrogen storage applications based on metal hydrides can provide solutions for such technologies. However there are still many technical challenges for both hydrogen storage material and ASSBs related to designing low-cost materials with low-environmental impact. The current materials considered for all-solid-state batteries should have high conductivities for Na+ Mg2+ and Ca2+ while Al3+-based compounds are often marginalised due to the lack of suitable electrode and electrolyte materials. In hydrogen storage materials the sluggish kinetic behaviour of solid-state hydride materials is one of the key constraints that limit their practical uses. Therefore it is necessary to overcome the kinetic issues of hydride materials before discussing and considering them on the system level. This review summarizes the achievements of the Marie Skłodowska-Curie Actions (MSCA) innovative training network (ITN) ECOSTORE the aim of which was the investigation of different aspects of (complex) metal hydride materials. Advances in battery and hydrogen storage materials for the efficient and compact storage of renewable energy production are discussed.
Methane Cracking for Hydrogen Production: A Review of Catalytic and Molten Media Pyrolysis
May 2022
Publication
Currently hydrogen is mainly generated by steam methane reforming with significant CO2 emissions thus exacerbating the greenhouse effect. This environmental concern promotes methane cracking which represents one of the most promising alternatives for hydrogen production with theoretical zero CO/CO2 emissions. Methane cracking has been intensively investigated using metallic and carbonaceous catalysts. Recently research has focused on methane pyrolysis in molten metals/salts to prevent both reactor coking and rapid catalyst deactivation frequently encountered in conventional pyrolysis. Another expected advantage is the heat transfer improvement due to the high heat capacity of molten media. Apart from the reaction itself that produces hydrogen and solid carbon the energy source used in this endothermic process can also contribute to reducing environmental impacts. While most researchers used nonrenewable sources based on fossil fuel combustion or electrical heating concentrated solar energy has not been thoroughly investigated to date for pyrolysis in molten media. However it could be a promising innovative pathway to further improve hydrogen production sustainability from methane cracking. After recalling the basics of conventional catalytic methane cracking and the developed solar cracking reactors this review delves into the most significant results of the state-of-the-art methane pyrolysis in melts (molten metals and salts) to show the advantages and the perspectives of this new path as well as the carbon products’ characteristics and the main factors governing methane conversion.
Dynamic Emulation of a PEM Electrolyzer by Time Constant Based Exponential Model
Feb 2019
Publication
The main objective of this paper is to develop a dynamic emulator of a proton exchange membrane (PEM) electrolyzer (EL) through an equivalent electrical model. Experimental investigations have highlighted the capacitive effect of EL when subjecting to dynamic current profiles which so far has not been reported in the literature. Thanks to a thorough experimental study the electrical domain of a PEM EL composed of 3 cells has been modeled under dynamic operating conditions. The dynamic emulator is based on an equivalent electrical scheme that takes into consideration the dynamic behavior of the EL in cases of sudden variation in the supply current. The model parameters were identified for a suitable current interval to consider them as constant and then tested with experimental data. The obtained results through the developed dynamic emulator have demonstrated its ability to accurately replicate the dynamic behavior of a PEM EL.
Overview of First Outcomes of PNR Project HYTUNNEL-CS
Sep 2021
Publication
Dmitry Makarov,
Donatella Cirrone,
Volodymyr V. Shentsov,
Sergii Kashkarov,
Vladimir V. Molkov,
Z. Xu,
Mike Kuznetsov,
Alexandros G. Venetsanos,
Stella G. Giannissi,
Ilias C. Tolias,
Knut Vaagsaether,
André Vagner Gaathaug,
Mark R. Pursell,
W. M. Rattigan,
Frank Markert,
Luisa Giuliani,
L.S. Sørensen,
A. Bernad,
Mercedes Sanz Millán,
U. Kummer,
C. Brauner,
Paola Russo,
J. van den Berg,
F. de Jong,
Tom Van Esbroeck,
M. Van De Veire,
D. Bouix,
Gilles Bernard-Michel,
Sergey Kudriakov,
Etienne Studer,
Domenico Ferrero,
Joachim Grüne and
G. Stern
The paper presents the first outcomes of the experimental numerical and theoretical studies performed in the funded by Fuel Cell and Hydrogen Joint Undertaking (FCH2 JU) project HyTunnel-CS. The project aims to conduct pre-normative research (PNR) to close relevant knowledge gaps and technological bottlenecks in the provision of safety of hydrogen vehicles in underground transportation systems. Pre normative research performed in the project will ultimately result in three main outputs: harmonised recommendations on response to hydrogen accidents recommendations for inherently safer use of hydrogen vehicles in underground traffic systems and recommendations for RCS. The overall concept behind this project is to use inter-disciplinary and inter-sectoral prenormative research by bringing together theoretical modelling and experimental studies to maximise the impact. The originality of the overall project concept is the consideration of hydrogen vehicle and underground traffic structure as a single system with integrated safety approach. The project strives to develop and offer safety strategies reducing or completely excluding hydrogen-specific risks to drivers passengers public and first responders in case of hydrogen vehicle accidents within the currently available infrastructure.
Techno-Economic Assessment of Natural Gas Pyrolysis in Molten Salts
Jan 2022
Publication
Steam methane reforming with CO2 capture (blue hydrogen) and water electrolysis based on renewable electricity (green hydrogen) are commonly assumed to be the main supply options in a future hydrogen economy. However another promising method is emerging in the form of natural gas pyrolysis (turquoise hydrogen) with pure carbon as a valuable by-product. To better understand the potential of turquoise hydrogen this study presents a techno-economic assessment of a molten salt pyrolysis process. Results show that moderate reactor pressures around 12 bar are optimal and that reactor size must be limited by accepting reactor performance well below the thermodynamic equilibrium. Despite this challenge stemming from slow reaction rates the simplicity of the molten salt pyrolysis process delivers high efficiencies and promising economics. In the long-term carbon could be produced for 200–300 €/ton granting access to high-volume markets in the metallurgical and chemical process industries. Such a scenario makes turquoise hydrogen a promising alternative to blue hydrogen in regions with public resistance to CO2 transport and storage. In the medium-term expensive first-of-a-kind plants could produce carbon around 400 €/ton if hydrogen prices are set by conventional blue hydrogen production. Pure carbon at this cost level can access smaller high-value markets such as carbon anodes and graphite ensuring profitable operation even for first movers. In conclusion the economic potential of molten salt pyrolysis is high and further demonstration and scale-up efforts are strongly recommended.
Full-scale Tunnel Experiments for Fuel Cell Hydrogen Vehicles: Jat Fire and Explosions
Sep 2021
Publication
In the framework of the HYTUNNEL-CS European project sponsored by FCH-JU a set of preliminary tests were conducted in a real tunnel in France. These tests are devoted to safety of hydrogen-fueled vehicles having a compressed gas storage and Temperature Pressure Release Device (TPRD). The goal of the study is to develop recommendations for Regulations Codes and Standards (RCS) for inherently safer use of hydrogen vehicles in enclosed transportation systems. Two scenarios were investigated (a) jet fire evolution following the activation of TPRD due to conventional fuel car fire and (b) explosion of compressed hydrogen tank. The obtained experimental data are systematically compared to existing engineering correlations. The results will be used for benchmarking studies using CFD codes. The hydrogen pressure range in these preliminary tests has been lowered down to 20MPa in order to verify the capability of various large-scale measurement techniques before scaling up to 70 MPa the subject of the second experimental campaign.
THyGA - Review on Other Projects Related to Mitigation and Identification of Useable Sensors in Existing Appliances
Jun 2022
Publication
The main goal of THyGA’s WP5 is to investigate ways to adapt residential or commercial appliances that have safety or performance issues to different levels of H2 concentrations in natural gas. This first deliverable presents some possible mitigation measures based on a literature study and some calculations.<br/>Acting on gas quality to avoid that hydrogen addition enhance current gas properties variations was explored several times in the past. Designing new appliances that could operate with variable gas composition including hydrogen. Dealing with existing appliances in order to guaranty safety for users and appliances.
Preliminary Risk Assessment (PRA) for Tests Planned in a Pilot Salt Cavern Hydrogen Storage in the Frame of the French Project STOPIL-H2
Sep 2021
Publication
The STOPIL-H2 project supported by the French Geodenergies research consortium aims to design a demonstrator for underground hydrogen storage in cavern EZ53 of the Etrez gas storage (France) operated by Storengy. Two types of tests are planned in this cavern: a tightness test with nitrogen and hydrogen then a cycling test during which the upper part of the cavern (approximately 200 m3) will be filled with hydrogen during 6 to 9 months. In this paper the PRA for the cycling test is presented comprising the identification of the major hazards and the proposed prevention and protection measures. The implemented methodology involves the following steps: data mining from the description of the project; analysis of lessons learned from accidents that occurred in underground gas storage and subface facilities; identification of the potential hazards pertaining to the storage process; analysis of external potential aggressors. Resulting as one of the outcomes of the PRA major accidental scenarios are presented and classified according to concerned storage operation phases as well as determined preventive or protective barriers able to prevent their occurrence of mitigate their consequences.
AMHYCO Project - Towards Advanced Accident Guidelines for Hydrogen Safety in Nuclear Power Plants
Sep 2021
Publication
Severe accidents in nuclear power plants are potentially dangerous to both humans and the environment. To prevent and/or mitigate the consequences of these accidents it is paramount to have adequate accident management measures in place. During a severe accident combustible gases — especially hydrogen and carbon monoxide — can be released in significant amounts leading to a potential explosion risk in the nuclear containment building. These gases need to be managed to avoid threatening the containment integrity which can result in the releases of radioactive material into the environment. The main objective of the AMHYCO project is to propose innovative enhancements in the way combustible gases are managed in case of a severe accident in currently operating reactors. For this purpose the AMHYCO project pursues three specific activities including experimental investigations of relevant phenomena related to hydrogen / carbon monoxide combustion and mitigation with PARs (Passive Autocatalytic Recombiners) improvement of the predictive capabilities of analysis tools used for explosion hazard evaluation inside the reactor containment as well as enhancement of the Severe Accident Management Guidelines (SAMGs) with respect to combustible gases risk management based on theoretical and experimental results. Officially launched on 1 October 2020 AMHYCO is an EU-funded Horizon 2020 project that will last 4 years from 2020 to 2024. This international project consists of 12 organizations (six from European countries and one from Canada) and is led by the Universidad Politécnica de Madrid (UPM). AMHYCO will benefit from the worldwide experts in combustion science accident management and nuclear safety in its Advisory Board. The paper will give an overview of the work program and planned outcome of the project.
Hydrogen Storage: Recent Improvements and Industrial Perspectives
Sep 2021
Publication
Efficient storage of hydrogen is crucial for the success of hydrogen energy markets. Hydrogen can be stored either as a compressed gas a refrigerated liquefied gas a cryo-compressed gas or in hydrides. This paper gives an overview of compressed hydrogen storage technologies focusing on high pressure storage tanks in metal and in composite materials. It details specific issues and constraints related to the materials and structure behavior in hydrogen and conditions representative of hydrogen energy uses. This paper is an update of the 2019 version that was presented in Australia. It especially covers recent progress made regarding regulations codes and standards for the design manufacturing periodic inspection and plastic materials’ evaluation of compressed hydrogen storage.
Overview on Hydrogen Risk Research and Development Activities: Methodology and Open Issues
Jan 2015
Publication
During the course of a severe accident in a light water nuclear reactor large amounts of hydrogen can be generated and released into the containment during reactor core degradation. Additional burnable gases [hydrogen (H2) and carbon monoxide (CO)] may be released into the containment in the corium/concrete interaction. This could subsequently raise a combustion hazard. As the Fukushima accidents revealed hydrogen combustion can cause high pressure spikes that could challenge the reactor buildings and lead to failure of the surrounding buildings. To prevent the gas explosion hazard most mitigation strategies adopted by European countries are based on the implementation of passive autocatalytic recombiners (PARs). Studies of representative accident sequences indicate that despite the installation of PARs it is difficult to prevent at all times and locations the formation of a combustible mixture that potentially leads to local flame acceleration. Complementary research and development (R&D) projects were recently launched to understand better the phenomena associated with the combustion hazard and to address the issues highlighted after the Fukushima Daiichi events such as explosion hazard in the venting system and the potential flammable mixture migration into spaces beyond the primary containment. The expected results will be used to improve the modeling tools and methodology for hydrogen risk assessment and severe accident management guidelines. The present paper aims to present the methodology adopted by Institut de Radioprotection et de Suˆ rete Nucleaire to assess hydrogen risk in nuclear power plants in particular French nuclear power plants the open issues and the ongoing R&D programs related to hydrogen distribution mitigation and combustion.
Life Cycle Assessments on Battery Electric Vehicles and Electrolytic Hydrogen: The Need for Calculation Rules and Better Databases on Electricity
May 2021
Publication
LCAs of electric cars and electrolytic hydrogen production are governed by the consumption of electricity. Therefore LCA benchmarking is prone to choices on electricity data. There are four issues: (1) leading Life Cycle Impact (LCI) databases suffer from inconvenient uncertainties and inaccuracies (2) electricity mix in countries is rapidly changing year after year (3) the electricity mix is strongly fluctuating on an hourly and daily basis which requires time-based allocation approaches and (4) how to deal with nuclear power in benchmarking. This analysis shows that: (a) the differences of the GHG emissions of the country production mix in leading databases are rather high (30%) (b) in LCA a distinction must be made between bundled and unbundled registered electricity certificates (RECs) and guarantees of origin (GOs); the residual mix should not be applied in LCA because of its huge inaccuracy (c) time-based allocation rules for renewables are required to cope with periods of overproduction (d) benchmarking of electricity is highly affected by the choice of midpoints and/or endpoint systems and (e) there is an urgent need for a new LCI database based on measured emission data continuously kept up-to-date transparent and open access.
Global Hydrogen Review 2021
Oct 2021
Publication
The Global Hydrogen Review is a new annual publication by the International Energy Agency to track progress in hydrogen production and demand as well as in other critical areas such as policy regulation investments innovation and infrastructure development.
The report is an output of the Clean Energy Ministerial Hydrogen Initiative (CEM H2I) and is intended to inform energy sector stakeholders on the status and future prospects of hydrogen while serving as an input to the discussions at the Hydrogen Energy Ministerial Meeting (HEM) organised by Japan. It examines what international progress on hydrogen is needed to help address climate change – and compares real-world developments with the stated ambitions of government and industry and with key actions under the Global Action Agenda launched at the HEM in 2019.
Focusing on hydrogen’s usefulness for meeting climate goals this Review aims to help decision makers fine-tune strategies to attract investment and facilitate deployment of hydrogen technologies while also creating demand for hydrogen and hydrogen-based fuels.
Link to International Energy Agency website
The report is an output of the Clean Energy Ministerial Hydrogen Initiative (CEM H2I) and is intended to inform energy sector stakeholders on the status and future prospects of hydrogen while serving as an input to the discussions at the Hydrogen Energy Ministerial Meeting (HEM) organised by Japan. It examines what international progress on hydrogen is needed to help address climate change – and compares real-world developments with the stated ambitions of government and industry and with key actions under the Global Action Agenda launched at the HEM in 2019.
Focusing on hydrogen’s usefulness for meeting climate goals this Review aims to help decision makers fine-tune strategies to attract investment and facilitate deployment of hydrogen technologies while also creating demand for hydrogen and hydrogen-based fuels.
Link to International Energy Agency website
On Board 70 MPA Hydrogen Composite Pressure Vessel Safety Factor
Sep 2021
Publication
The safety factor of a composite structure in relation to its mechanical rupture is an important criterion for the safety of a 70 MPa composite pressure vessel for hydrogen storage particularly for on-board applications (car bus truck train…). After an introduction of Type IV technology the contribution of carbon fibre composite material structure manufacturing process of pressure vessels and environmental effects on the safety factor are commented. Thanks to an experimental-based evaluation on composite material and H2 composite pressure vessel the safety margins are addressed.
THyGA - Tightness Testing of Gas Distribution Components in 40%H2+60%CH4
Aug 2022
Publication
The present work is concerned with the evaluation of the tightness of the components located on domestic and commercial gas lines from the gas meter to the end user appliance in presence of a mixture 40%H2+60%CH4 at 35 mbar. The components were taken from installations being used currently in Germany Denmark Belgium and France. The current standard methods to evaluate natural gas distribution tightness propose testing duration of several minutes. In this work the components tightness was first evaluated using such standard methods before carrying out tests on longer period of time and evaluate the potential influence of time and the results were compared to admissible leakage rates for natural gas in distribution network and in appliances.
Impact of Hydrogen Liquefaction on Hydrogen Fuel Quality for Transport Applications (ISO-14687:2019)
Aug 2022
Publication
Decarbonisation of the energy sector is becoming increasingly more important to the reduction in climate change. Renewable energy is an effective means of reducing CO2 emissions but the fluctuation in demand and production of energy is a limiting factor. Liquid hydrogen allows for long-term storage of energy. Hydrogen quality is important for the safety and efficiency of the end user. Furthermore the quality of the hydrogen gas after liquefaction has not yet been reported. The purity of hydrogen after liquefaction was assessed against the specification of Hydrogen grade D in the ISO-14687:2019 by analysing samples taken at different locations throughout production. Sampling was carried out directly in gas cylinders and purity was assessed using multiple analytical methods. The results indicate that the hydrogen gas produced from liquefaction is of a higher purity than the starting gas with all impurities below the threshold values set in ISO-14687:2019. The amount fraction of water measured in the hydrogen sample increased with repeated sampling from the liquid hydrogen tank suggesting that the sampling system used was affected by low temperatures (−253 ◦C). These data demonstrate for the first time the impact of liquefaction on hydrogen purity assessed against ISO-14687:2019 showing that liquified hydrogen is a viable option for long-term energy storage whilst also improving quality.
Reducing the Cost of Low-carbon Hydrogen Production via Emerging Chemical Looping Process
Jan 2023
Publication
A thorough techno-economic analysis where inherent carbon capture is examined against state-of-the-art blue hydrogen production configurations for large (100000 Nm3 /h) and very large (333000 Nm3 /h) capacities. Advanced solvent-based technologies based on post-combustion capture and auto-thermal reformer combined with a gas heated reformer are simulated with process flowsheet software and compared with the emerging chemical looping process. A network of dynamically operated packed bed reactors has been designed and modelled using an in-house code and key parameters generating uncertainties in the results have been examined in a sensitivity analysis. The chemical looping reforming process presents a higher net reforming efficiency than the benchmark cases (8.2 % higher at large scale and 1.5 % higher at very large scale) ranged 75.4–75.7 % while the specific energy for CO2 avoidance is negative in the range of − 0.78 to − 0.85 MJ/kgCO2. In the carbon capture cases the chemical looping reforming in packed beds technology generated a levelised cost of hydrogen of 168.9 £/kNm3 H2 for the large scale and 159.1 £/kNm3 H2 for the very large scale with the values for the benchmark cases being higher at 196.4 and 166.6 £/kNm3 H2 respectively while the levelised cost of hydrogen values are 1 % higher in the benchmark cases where carbon emission price is accounted for. The carbon capture ratio is 99.9 % for the chemical looping reforming cases compared to 90–91 % for the benchmark ones thus providing a significant foreground for the scale-up and implementation of chemical looping reforming technologies for hydrogen production.
Corrosion of Structural Components of Proton Exchange Membrane Water Electrolyzer Anodes: A Review
Dec 2022
Publication
Proton exchange membrane (PEM) water electrolysis is one of the low temperature processes for producing green hydrogen when coupled with renewable energy sources. Although this technology has already reached a certain level of maturity and is being implemented at industrial scale its high capital expenditures deriving from the utilization of expensive corrosion-resistant materials limit its economic competitiveness compared to the widespread fossil fuel-based hydrogen production such as steam reforming. In particular the structural elements like bipolar plates (BPP) and porous transports layers (PTL) are essentially made of titanium protected by precious metal layers in order to withstand the harsh oxidizing conditions in the anode compartment. This review provides an analysis of literature on structural element degradation on the oxygen side of PEM water electrolyzers from the early investigations to the recent developments involving novel anti-corrosion coatings that protect more cost-effective BPP and PTL materials like stainless steels.
A Simple and Low-cost Integrative Sensor System for Methane and Hydrogen Measurement
Sep 2020
Publication
Energy production by methanization or gasification of biomass is dependant on the chemical composition of the gas generated. The resistive sensors based on semiconductor metal oxides like the MQ series sensors are inexpensive and frequently used in gas detection. These sensors initially dedicated to detecting gas leaks in safety systems have relatively small measurement ranges (i.e. limited to concentrations below 10000 ppm). It is therefore necessary to find solutions to adapt these categories of sensors for gas measurements in the energy sector where the gas concentration is much more significant. In this article we propose a protocol using an adaptable capsule for MQ-4 and MQ-8 sensors to measure high concentrations of CH4 and H2 respectively. The technique consists of diluting the gas to be studied in a known volume of air. Three methods are proposed and compared regarding the linearity and the repeatability of the measurements. The first method was done in an airtight enclosed chamber the second method consists of directly injecting the gas on the sensor placed in an open environment and the final method was accomplished by direct injection of the gas on the sensor placed in a partially closed capsule. Comparisons show that the first technique provides the best repeatability with a maximum standard deviation of 13.88% for CH4 measurement and 5.1% for H2. However its linearity is weak (i.e. R2 ¼ 0.8637 for CH4 and R2 ¼ 0.5756 for H2). The second technique has better linearity but bad repeatability. The third technique presents the best results with R2 values of 0.9973 for the CH4 measurement and 0.9472 for H2. The use of the partially closed capsule resulted in an acceptable linear response of the sensors by up to 20% concentration of CH4 and until 13.33% concentration of H2 in the studied gas. The use of this simple and low-cost technique facilitates the characterization of combustible gases in isolated areas. It allows local operators of biomass valorization systems to control and improve their installations while avoiding the high costs of conventional measurement devices. This study hence contributes to the development of rural electrification projects in remote areas.
Regional Uptake of Direct Reduction Iron Production Using Hydrogen Under Climate Policy
Nov 2022
Publication
The need to reduce CO2 emissions to zero by 2050 has meant an increasing focus on high emitting industrial sectors such as steel. However significant uncertainties remain as to the rate of technology diffusion across steel production pathways in different regions and how this might impact on climate ambition. Informed by empirical analysis of historical transitions this paper presents modelling on the regional deployment of Direction Reduction Iron using hydrogen (DRI-H2). We find that DRI-H2 can play a leading role in the decarbonisation of the sector leading to near-zero emissions by 2070. Regional spillovers from early to late adopting regions can speed up the rate of deployment of DRI-H2 leading to lower cumulative emissions and system costs. Without such effects cumulative emissions are 13% higher than if spillovers are assumed and approximately 15% and 20% higher in China and India respectively. Given the estimates of DRI-H2 cost-effectiveness relative to other primary production technologies we also find that costs increase in the absence of regional spillovers. However other factors can also have impacts on deployment emission reductions and costs including the composition of the early adopter group material efficiency improvements and scrap recycling rates. For the sector to achieve decarbonisation key regions will need to continue to invest in low carbon steel projects recognising their broader global benefit and look to develop and strengthen policy coordination on technologies such as DRI-H2.
Far Off-shore Wind Energy-based Hydrogen Production: Technological Assessment and Market Valuation Designs
Jan 2020
Publication
This article provides a techno-economic study on coupled offshore wind farm and green hydrogen production via sea water electrolysis (OWF-H2). Offshore wind energy wind farms (OWF) and water electrolysis (WE) technologies are described. MHyWind (the tool used to perform simulations and optimisations of such plants) is presented as well as the models of the main components in the study. Three case studies focus on offshore wind farms either stand-alone or connected to the grid via export cables coupled with a battery and electrolysis systems either offshore or onshore. Exhaustive searches and optimisations performed allowed for rules of thumb to be derived on the sizing of coupled OWF-H2 plants that minimize costs of hydrogen production (LCoH2 in €/kgH2): Non-connected OWF-H2 coupled to a battery offers the lowest LCoH2 without the costs of H2 transportation when compared to cases where the WE is installed onshore and connected to the OWF. Using a simple power distribution heuristic increasing the number of installed WE allows the system to take advantage of more OWF energy but doesn’t improve plant efficiency whereas a battery always does. Finally within the scope of this study it is observed that power ratios of optimized plant architectures (leading to the lowest LCoH2) are between 0.8-0.9 for PWE/POWF and 0.3-0.35 for PBattery/POWF.
Hydrogen Projects Database – Analysis
Jun 2020
Publication
The IEA produced this dataset as part of efforts to track advances in low-carbon hydrogen technology. It covers all projects commissioned worldwide since 2000 to produce hydrogen for energy or climate-change-mitigation purposes. It includes projects which their objective is either to reduce emissions associated with producing hydrogen for existing applications or to use hydrogen as an energy carrier or industrial feedstock in new applications that have the potential to be a low-carbon technology. Projects in planning or construction are also covered.
Link to Download Database from IEA Website
Link to Download Database from IEA Website
Relevance of Optimized Low-Scale Green H2 Systems in a French Context: Two Case Studies
May 2022
Publication
Hydrogen has been identified as a very promising vector for energy storage especially for heavy mobility applications. For this reason France is making significant investments in this field and use cases need to be evaluated as they are sprouting. In this paper the relevance of H2 in two storage applications is studied: a domestic renewable electricity production system connected to the grid and a collective hydrogen production for the daily bus refill. The investigation consists of the sizing of the system and then the evaluation of its performance according to several criteria depending on case. Optimizations are made using Bayesian and gradient-based methods. Several variations around a central case are explored for both cases to give insights on the impact of the different parameters (location pricing objective etc.) on the performance of the system.Our results show that domestic power-to-power applications (case 1) do not seem to be competitive with electrochemical storage. Meanwhile without any subsidies or incentives such configuration does not allow prosumers to save money (+16% spendings compared to non-equipped dwelling). It remains interesting when self-sufficiency is the main objective (up to 68% of energy is not exchanged). The power-to-gas application (case 2 central case) with a direct use of hydrogen for mobility seems to be more relevant according to our case study we could reach a production cost of green H2 around 5 €/kg similar to the 3–10 $/kg found in literature for 182 houses involved. In both cases H2 follows a yearly cycle charging in summer and discharging in winter (long term storage) due to low conversion efficiency.
Use of Hydrogen in Off-Grid Locations, a Techno-Economic Assessment
Nov 2018
Publication
Diesel generators are currently used as an off-grid solution for backup power but this causes CO2 and GHG emissions noise emissions and the negative effects of the volatile diesel market influencing operating costs. Green hydrogen production by means of water electrolysis has been proposed as a feasible solution to fill the gaps between demand and production the main handicaps of using exclusively renewable energy in isolated applications. This manuscript presents a business case of an off-grid hydrogen production by electrolysis applied to the electrification of isolated sites. This study is part of the European Ely4off project (n◦ 700359). Under certain techno-economic hypothesis four different system configurations supplied exclusively by photovoltaic are compared to find the optimal Levelized Cost of Electricity (LCoE): photovoltaic-batteries photovoltaic-hydrogen-batteries photovoltaic-diesel generator and diesel generator; the influence of the location and the impact of different consumptions profiles is explored. Several simulations developed through specific modeling software are carried out and discussed. The main finding is that diesel-based systems still allow lower costs than any other solution although hydrogen-based solutions can compete with other technologies under certain conditions.
Main Hydrogen Production Processes: An Overview
May 2021
Publication
Due to its characteristics hydrogen is considered the energy carrier of the future. Its use as a fuel generates reduced pollution as if burned it almost exclusively produces water vapor. Hydrogen can be produced from numerous sources both of fossil and renewable origin and with as many production processes which can use renewable or non-renewable energy sources. To achieve carbon neutrality the sources must necessarily be renewable and the production processes themselves must use renewable energy sources. In this review article the main characteristics of the most used hydrogen production methods are summarized mainly focusing on renewable feedstocks furthermore a series of relevant articles published in the last year are reviewed. The production methods are grouped according to the type of energy they use; and at the end of each section the strengths and limitations of the processes are highlighted. The conclusions compare the main characteristics of the production processes studied and contextualize their possible use.
Ignition of Hydrogen-air Mixtures Under Volumetric Expansion Conditions
Sep 2017
Publication
A better understanding of chemical kinetics under volumetric expansion is important for a number of situations relevant to industrial safety including detonation diffraction and direct initiation reflected shock-ignition at obstacles ignition behind a decaying shock among others. The ignition of stoichiometric hydrogen-air mixtures was studied using 0D numerical simulations with time-dependent specific volume variations. The competition between chemical energy release and expansion-induced cooling was characterized for different cooling rates and mathematical forms describing the shock decay rate. The critical conditions for reaction quenching were systematically determined and the thermo-chemistry dynamics were analyzed near the critical conditions.
Risk Assessment of a Gaseous Hydrogen Fueling Station (GHFs)
Sep 2021
Publication
Promoted by national and European investment plans promoting the use of hydrogen as energy carrier the number of Gaseous Hydrogen Fueling Station (or GHFS) has been growing up quite significantly over the past years. Considering the new possible hazards and the related accidents induced by these installations like seen in 2019 in Norway this paper presents a risk assessment of a typical GHFS using the same methodology as the one required in France by the authorities for Seveso facilities. The fact that a hydrogen fueling station could be used by a public not particularly trained to handle hydrogen underlines the importance of this risk assessment. In this article typical components related to GHFS (dispenser high pressure storage compressor low pressure storage) are listed and the hazard potentials linked to these components and the substances involved are identified. Based on these elements and an accidentology a risk analysis has been conducted in order to identify all accidental situations that could occur. The workflow included a detailed risk assessment consisting in modeling the thermal and explosion effects of all hazardous phenomena and in assessing the probability of occurrence for these scenarios. Regarding possible mitigation measures the study was based on an international benchmark for codes and standards made for GFHS. These preliminary outcomes of this study may be useful for any designer and/or owner of a GFHS.
Detection of Contaminants in Hydrogen Fuel for Fuel Cell Electrical Vehicles with Sensors—Available Technology, Testing Protocols and Implementation Challenges
Dec 2021
Publication
Europe’s low-carbon energy policy favors a greater use of fuel cells and technologies based on hydrogen used as a fuel. Hydrogen delivered at the hydrogen refueling station must be compliant with requirements stated in different standards. Currently the quality control process is performed by offline analysis of the hydrogen fuel. It is however beneficial to continuously monitor at least some of the contaminants onsite using chemical sensors. For hydrogen quality control with regard to contaminants high sensitivity integration parameters and low cost are the most important requirements. In this study we have reviewed the existing sensor technologies to detect contaminants in hydrogen then discussed the implementation of sensors at a hydrogen refueling stations described the state-of-art in protocols to perform assessment of these sensor technologies and finally identified the gaps and needs in these areas. It was clear that sensors are not yet commercially available for all gaseous contaminants mentioned in ISO14687:2019. The development of standardized testing protocols is required to go hand in hand with the development of chemical sensors for this application following a similar approach to the one undertaken for air sensors.
Chemical Inhibition of Premixed Hydrogen-air Flames: Experimental Investigation using a 20-litre Vessel
Sep 2021
Publication
Throughout the history of the mining petroleum process and nuclear industries continuous efforts have been made to develop and improve measures to prevent and mitigate accidental explosions. Over the coming decades energy systems are expected to undergo a transition towards sustainable use of conventional hydrocarbons and an increasing share of renewable energy sources in the global energy mix. The variable and intermittent supply of energy from solar and wind points to energy systems based on hydrogen or hydrogen-based fuels as the primary energy carriers. However the safety-related properties of hydrogen imply that it is not straightforward to achieve and document the same level of safety for hydrogen systems compared to similar systems based on established fuels such as petrol diesel and natural gas. Compared to the conventional fuels hydrogen-air mixtures have lower ignition energy higher combustion reactivity and a propensity to undergo deflagration-to-detonation-transition (DDT) under certain conditions. To achieve an acceptable level of safety it is essential to develop effective measures for mitigating the consequences of hydrogen explosions in systems with certain degree of congestion and confinement. Extensive research over the last decade have demonstrated that chemical inhibition or partial suppression can be used for mitigating the consequences of vapour cloud explosions (VCEs) in congested process plants. Total and cooperation partners have demonstrated that solid flame inhibitors injected into flammable hydrocarbon-air clouds represent an effective means of mitigating the consequences of VCEs involving hydrocarbons. For hydrogen-air explosions these same chemicals inhibitors have not proved effective. It is however well-known that hydrocarbons can affect the burning velocity of hydrogen-air mixtures greatly. This paper gives an overview over previous work on chemical inhibitors. In addition experiments in a 20-litre vessel have been performed to investigate the effect of combinations of hydrocarbons and alkali salts on hydrogen/air mixtures.
Value of Green Hydrogen When Curtailed to Provide Grid Balancing Services
Aug 2022
Publication
This paper evaluates the potential of grid services in France Italy Norway and Spain to provide an alternative income for electrolysers producing hydrogen from wind power. Grid services are simulated with each country's data for 2017 for energy prices grid services and wind power profiles from relevant wind parks. A novel metric is presented the value of curtailed hydrogen which is independent from several highly uncertain parameters such as electrolyser cost or hydrogen market price. Results indicate that grid services can monetise the unused spare capacity of electrolyser plants improving their economy in the critical deployment phase. For most countries up-regulation yields a value of curtailed hydrogen above 6 V/kg over 3 times higher than the EU's 2030 price target (without incentives). However countries with large hydro power resources such as Norway yield far lower results below 2 V/kg. The value of curtailed hydrogen also decreases with hydrogen production corresponding to the cases of symmetric and down-regulation.
Energy Efficiency Based Control Strategy of a Three-Level Interleaved DC-DC Buck Converter Supplying a Proton Exchange Membrane Electrolyzer
Aug 2019
Publication
To face the intensive use of natural gas and other fossil fuels to generate hydrogen water electrolysis based on renewable energy sources (RES) seems to be a viable solution. Due to their fast response times and high efficiency proton exchange membrane electrolyzer (PEM EL) is the most suitable technology for long-term energy storage combined with RES. Like fuel cells the development of fit DC-DC converters is mandatory to interface the EL to the DC grid. Given that PEM EL operating voltages are quite low and to meet requirements in terms of output current ripples new emerging interleaved DC-DC converter topologies seem to be the best candidates. In this work a three-level interleaved DC-DC buck converter has been chosen to supply a PEM EL from a DC grid. Therefore the main objective of this paper is to develop a suitable control strategy of this interleaved topology connected to a PEM EL emulator. To design the control strategy investigations have been carried out on energy efficiency hydrogen flow rate and specific energy consumption. The obtained experimental results validate the performance of the converter in protecting the PEM EL during transient operations while guaranteeing correct specific energy consumption.
Protocol for Heavy-duty Hydrogen Refueling: A Modelling Benchmark
Sep 2021
Publication
For the successful deployment of the Heavy Duty (HD) hydrogen vehicles an associated infrastructure in particular hydrogen refueling stations (HRS) should be reliable compliant with regulations and optimized to reduce the related costs. FCH JU project PRHYDE aims to develop a sophisticated protocol dedicated to HD applications. The target of the project is to develop protocol and recommendations for an efficient refueling of 350 500 and 700 bar HD tanks of types III and IV. This protocol is based on modeling results as well as experimental data. Different partners of the PRHYDE European project are closely working together on this target. However modeling approaches and corresponding tools must first be compared and validated to ensure the high level of reliability for the modeling results. The current paper presents the benchmark performed in the frame of the project by Air Liquide Engie Wenger Engineering and NREL. The different models used were compared and calibrated to the configurations proposed by the PRHYDE project. In addition several scenarios were investigated to explore different cases with high ambient temperatures.
Global Hydrogen Review 2022
Sep 2022
Publication
The Global Hydrogen Review is an annual publication by the International Energy Agency that tracks hydrogen production and demand worldwide as well as progress in critical areas such as infrastructure development trade policy regulation investments and innovation.
The report is an output of the Clean Energy Ministerial Hydrogen Initiative and is intended to inform energy sector stakeholders on the status and future prospects of hydrogen while also informing discussions at the Hydrogen Energy Ministerial Meeting organised by Japan. Focusing on hydrogen’s potentially major role in meeting international energy and climate goals this year’s Review aims to help decision makers fine-tune strategies to attract investment and facilitate deployment of hydrogen technologies while also creating demand for hydrogen and hydrogen-based fuels. It compares real-world developments with the stated ambitions of government and industry.
This year’s report includes a special focus on how the global energy crisis sparked by Russia’s invasion of Ukraine has accelerated the momentum behind hydrogen and on the opportunities that it offers to simultaneously contribute to decarbonisation targets and enhance energy security.
The report can be found on their website.
The report is an output of the Clean Energy Ministerial Hydrogen Initiative and is intended to inform energy sector stakeholders on the status and future prospects of hydrogen while also informing discussions at the Hydrogen Energy Ministerial Meeting organised by Japan. Focusing on hydrogen’s potentially major role in meeting international energy and climate goals this year’s Review aims to help decision makers fine-tune strategies to attract investment and facilitate deployment of hydrogen technologies while also creating demand for hydrogen and hydrogen-based fuels. It compares real-world developments with the stated ambitions of government and industry.
This year’s report includes a special focus on how the global energy crisis sparked by Russia’s invasion of Ukraine has accelerated the momentum behind hydrogen and on the opportunities that it offers to simultaneously contribute to decarbonisation targets and enhance energy security.
The report can be found on their website.
Numerical Modeling of a Moderate Hydrogen Leakage in a Typical Two-vented Fuel Cell Configuration
Sep 2021
Publication
Numerical results are presented from two direct numerical simulations (DNS) where a moderate hydrogen leakage is modeled in a typical two-vented fuel cell configuration. The study mimics one of the experimental investigations carried out on the 1 m3 enclosure with a leak flow rate of 10.4 Nl.min−1 [1]. The injection dimensionless Richardson number is at the order of unity and thus characterizes a plume flow which becomes turbulent due to gravitational accelerations. Two large exterior regions are added to the computational domain to model correctly the exchange between the in/out flows at both vents and the outer environment. Two meshes are used in this study; a first consisting of 250 million cells while the second has 2 billion cells to ensure the fine DNS resolution at the level of Kolmogorov and Batchelor length scales. The high performance computation (HPC) platform TRUST is employed where the computational domain is distributed up to 5.104 central processing unit (CPU) cores. A detailed description of the flow structure and the hydrogen dispersion is provided where the sharp effect of the cross-flow on the plume is analyzed. Comparisons versus the experimental measurements show a very good agreement where both the bi-layer Linden regime and the maximal concentration in the top homogeneous layer are correctly reproduced by the DNS. This result is extremely important and breaks the limitations shown previously with statistical RANS approaches and LES models. This study can be considered as a good candidate for any further improvements of the theoretical industrial plume models in general and for the estimation of the non-constant entrainment coefficient in particular.
Intermetallic Compounds Synthesized by Mechanical Alloying for Solid-State Hydrogen Storage: A Review
Sep 2021
Publication
Hydrogen energy is a very attractive option in dealing with the existing energy crisis. For the development of a hydrogen energy economy hydrogen storage technology must be improved to over the storage limitations. Compared with traditional hydrogen storage technology the prospect of hydrogen storage materials is broader. Among all types of hydrogen storage materials solid hydrogen storage materials are most promising and have the most safety security. Solid hydrogen storage materials include high surface area physical adsorption materials and interstitial and non-interstitial hydrides. Among them interstitial hydrides also called intermetallic hydrides are hydrides formed by transition metals or their alloys. The main alloy types are A2B AB AB2 AB3 A2B7 AB5 and BCC. A is a hydride that easily forms metal (such as Ti V Zr and Y) while B is a non-hydride forming metal (such as Cr Mn and Fe). The development of intermetallic compounds as hydrogen storage materials is very attractive because their volumetric capacity is much higher (80–160 kgH2m−3 ) than the gaseous storage method and the liquid storage method in a cryogenic tank (40 and 71 kgH2m−3 ). Additionally for hydrogen absorption and desorption reactions the environmental requirements are lower than that of physical adsorption materials (ultra-low temperature) and the simplicity of the procedure is higher than that of non-interstitial hydrogen storage materials (multiple steps and a complex catalyst). In addition there are abundant raw materials and diverse ingredients. For the synthesis and optimization of intermetallic compounds in addition to traditional melting methods mechanical alloying is a very important synthesis method which has a unique synthesis mechanism and advantages. This review focuses on the application of mechanical alloying methods in the field of solid hydrogen storage materials.
Ammonia Production from Clean Hydrogen and the Implications for Global Natural Gas Demand
Jan 2023
Publication
Non-energy use of natural gas is gaining importance. Gas used for 183 million tons annual ammonia production represents 4% of total global gas supply. 1.5-degree pathways estimate an ammonia demand growth of 3–4-fold until 2050 as new markets in hydrogen transport shipping and power generation emerge. Ammonia production from hydrogen produced via water electrolysis with renewable power (green ammonia) and from natural gas with CO2 storage (blue ammonia) is gaining attention due to the potential role of ammonia in decarbonizing energy value chains and aiding nations in achieving their net-zero targets. This study assesses the technical and economic viability of different routes of ammonia production with an emphasis on a systems level perspective and related process integration. Additional cost reductions may be driven by optimum sizing of renewable power capacity reducing losses in the value chain technology learning and scale-up reducing risk and a lower cost of capital. Developing certification and standards will be necessary to ascertain the extent of greenhouse gas emissions throughout the supply chain as well as improving the enabling conditions including innovative finance and de-risking for facilitating international trade market creation and large-scale project development.
Mathematical Modeling of Unstable Transport in Underground Hydrogen Storage
Apr 2015
Publication
Within the framework of energy transition hydrogen has a great potential as a clean energy carrier. The conversion of electricity into hydrogen for storage and transport is an efficient technological solution capable of significantly reducing the problem of energy shortage. Underground hydrogen storage (UHS) is the best solution to store the large amount of excess electrical energy arising from the excessive over-production of electricity with the objective of balancing the irregular and intermittent energy production typical of renewable sources such as windmills or solar. Earlier studies have demonstrated that UHS should be qualitatively identical to the underground storage of natural gas. Much later however it was revealed that UHS is bound to incur peculiar difficulties as the stored hydrogen is likely to be used by the microorganisms present in the rocks for their metabolism which may cause significant losses of hydrogen. This paper demonstrates that besides microbial activities the hydrodynamic behavior of UHS is very unique and different from that of a natural gas storage.
Fuel-scale Tunnel Experiments for Fuel Cell Hydrogen Vehicles: Gas Dispersion
Sep 2021
Publication
In the framework of the HYTUNNEL-CS European project sponsored by FCH-JU a set of preliminary tests were conducted in a real tunnel in France. These tests are devoted to safety of hydrogen-fueled vehicles having a compressed gas storage and Temperature Pressure Release Device (TPRD). The goal of the study is to develop recommendations for Regulations Codes and Standards (RCS) for inherently safer use of hydrogen vehicles in enclosed transportation systems. In these preliminary tests the helium gas has been employed instead of hydrogen. Upward and downward gas releases following by TPRD activation has been considered. The experimental data describing local behavior (close to jet or below the chassis) as well as global behavior at the tunnel scale are obtained. These experimental data are systematically compared to existing engineering correlations. The results will be used for benchmarking studies using CFD codes. The hydrogen pressure range in these preliminary tests has been lowered down to 20MPa in order to verify the capability of various large-scale measurement techniques before scaling up to 70MPa the subject of the second campaign.
On the Possibility to Simulate the Operation of a SI Engine using Alternative Gaseous Fuels
Nov 2019
Publication
A thermodynamic combustion model developed in AVL BOOST software was used in order to evaluate the pollutant emissions performance and efficiency parameters of a spark ignition engine Renault K7M-710 fueled with compressed natural gas hydrogen and blends of compressed natural gas and hydrogen (hythane). Multiple research studies have concluded that for the near future hythane could be the most promising alternative fuel because it has the advantages of both its components. In our previous work the model was validated for the performance and efficiency parameters by comparison of simulation results with experimental data acquired when the engine was fueled with gasoline. In this work the model was improved and can predict the values of pollutant emissions when the engine is running with the studied alternative fuels. As the percentage of hydrogen in hythane is increased the power of the engine rises the brake specific fuel consumption carbon dioxide carbon monoxide and total unburned hydrocarbon emissions decrease while nitrogen oxides increase. The values of peak fire pressure maximum pressure derivative and peak fire temperature in cycle are higher leading to an increased probability of knock occurrence. To avoid this phenomenon an optimum correlation between the natural gas-hydrogen blend the air-fuel ratio the spark advance and the engine operating condition needs to be found.
French Guide to Conformity Assessment and Certification of Hydrogen Systems
Sep 2021
Publication
Hydrogen as energy carrier is referenced in French and European political strategies to realize the transition to low-carbon energy. In 2020 in France the government was launching a major investment plan amounting to 7.2 billion euros until 2030 to support the deployment of large-scale hydrogen technologies [1]. The implementation of this strategy should lead to the arrival of several new hydrogen systems that will need to be evaluated and certified regarding their compliance with safety requirements before being commercialized. Conformity assessment and certification play an important role to achieve a good safety level on the EU market for the protection of workers and consumers. It is a way for the manufacturer to prove that hazards have been identified and risks are managed and to demonstrate his commitment to safety that are key to access to the EU market. To assist manufacturers in identifying the applicable regulations standards and procedures for putting their product on the market Ineris elaborated a guidebook [2] with financial and technical support by ADEME the French Agency for Ecological Transition and France Hydrogen the French Association for Hydrogen and Fuel Cells. The preparation of this document also led to identifying gaps in the Regulations Codes and Standards (RCS) framework and necessary resources for the implementation of the conformity assessment procedures. This paper first describes the main regulatory procedures applicable for various types of hydrogen systems. Then describes the role of the actors involved in this process with a special focus on the French context. And finally focuses on some of the gaps that were identified and formulates suggestions to address them.
Numerical Simulations of Atmospheric Dispersion of Large-scale Liquid Hydrogen Releases
Sep 2021
Publication
Numerical simulations have been conducted for LH2 massive releases and the subsequent atmospheric dispersion using an in-house modified version of the open source computational fluid dynamics (CFD) code OpenFOAM. A conjugate heat transfer model has been added for heat transfer between the released LH2 and the ground. Appropriate interface boundary conditions are applied to ensure the continuities of temperature and heat fluxes. The significant temperature difference between the cryogenic hydrogen and the ground means that the released LH2 will instantly enter in a boiling state resulting in a hydrogen- air gaseous cloud which will initially behave like a dense gas. Numerical predictions have been conducted for the subsequent atmospheric dispersion of the vaporized LH2 for a series of release scenarios - with and without retention pits - to limit the horizontal spread of the LH2 on the ground. The considered cases included the instantaneous release of 1 10 and 50 tons of LH2 under neutral (D) and stable (F) weather conditions. More specifically 3F and 5D conditions were simulated with the former representing stable weather conditions under wind speed of 3 m/s at 10 m above the ground and the later corresponding to neutral weather conditions under 5 m/s wind speed (10 m above the ground). Specific numerical tests have also been conducted for selected scenarios under different ambient temperatures from 233 up to 313 K. According to the current study although the retention pit can extend the dispersion time it can significantly reduce the extent of hazards due to much smaller cloud size within both the flammability and explosion limits. While the former has negative impact on safety the later is beneficial. The use of retention pit should hence be considered with caution in practical applications.
Hydrogen-assisted Fatigue Crack Growth: Pre-charging vs In-situ Testing in Gaseous Environments
Mar 2023
Publication
We investigate the implications of conducting hydrogen-assisted fatigue crack growth experiments in a hydrogen gas environment (in-situ hydrogen charging) or in air (following exposure to hydrogen gas). The study is conducted on welded 42CrMo4 steel a primary candidate for the future hydrogen transport infrastructure allowing us to additionally gain insight into the differences in behavior between the base steel and the coarse grain heat affected zone. The results reveal significant differences between the two testing approaches and the two weld regions. The differences are particularly remarkable for the comparison of testing methodologies with fatigue crack growth rates being more than one order of magnitude higher over relevant loading regimes when the samples are tested in a hydrogen-containing environment relative to the pre-charged samples. Aided by finite element modelling and microscopy analysis these differences are discussed and rationalized. Independent of the testing approach the heat affected zone showed a higher susceptibility to hydrogen embrittlement. Similar microstructural behavior is observed for both testing approaches with the base metal exhibiting martensite lath decohesion while the heat affected zone experienced both martensite lath decohesion and intergranular fracture.
Proton Exchange Membrane Electrolyzer Emulator for Power Electronics Testing Applications
Mar 2021
Publication
This article aims to develop a proton exchange membrane (PEM) electrolyzer emulator. This emulator is realized through an equivalent electrical scheme. It allows taking into consideration the dynamic operation of PEM electrolyzers which is generally neglected in the literature. PEM electrolyzer dynamics are reproduced by the use of supercapacitors due to the high value of the equivalent double-layer capacitance value. Steady-state and dynamics operations are investigated in this work. The design criteria are addressed. The PEM electrolyzer emulator is validated by using a 400-W commercial PEM electrolyzer. This emulator is conceived to test new DC-DC converters to supply the PEM ELs and their control as well avoiding the risk to damage a real electrolyzer for experiment purposes. The proposed approach is valid both for a single cell and for the whole stack emulation.
Risk Assessment and Mitigation Evaluation for Hydrogen Vehicles in Private Garages. Experiments and Modelling
Sep 2021
Publication
Governments and local authorities introduce new incentives and regulations for cleaner mobility as part of their environmental strategies to address energy challenges. Fuel cell electric vehicles (FCEVs) are becoming increasingly important and will extend beyond captive fleets reaching private users. Research on hydrogen safety issues is currently led in several projects in order to highlight and manage risks of FCEVs in confined spaces such as tunnels underground parkings repair garages etc. But what about private garages - that involve specific geometries volumes congestion ventilation? This study has been carried out in the framework of PRHyVATE JIP project which aims at better understanding hydrogen build-up and distribution in a private garage. The investigation went through different rates and modes of ventilation. As first step an HAZID (Hazard Identification) has been realized for a generic FCEV. This preliminary work allowed to select and prioritize accidental release scenarios to be explored experimentally with helium in a 40-m3 garage. Several configurations of release ventilation modes and congestion – in transient regime and at steady state – have been tested. Then analytical and numerical calculation approaches have been applied and adjusted to develop a simplified methodology. This methodology takes into account natural ventilation for assessment of hydrogen accumulation and mitigation means optimization. Finally a global risk evaluation – including ignition of a flammable hydrogen-air mixture – has been performed to account for the mostly feared events and to evaluate their consequences in a private garage. Thus preliminary recommendations good practices and safety features for safely parking FCEVs in private garages can be proposed.
Impacts of Greenhouse Gas Neutrality Strategies on Gas Infrastructure and Costs: Implications from Case Studies Based on French and German GHG-neutral Scenarios
Sep 2022
Publication
The European Union’s target to reach greenhouse gas neutrality by 2050 calls for a sharp decrease in the consumption of natural gas. This study assesses impacts of greenhouse gas neutrality on the gas system taking France and Germany as two case studies which illustrate a wide range of potential developments within the European Union. Based on a review of French and German GHG-neutral scenarios it explores impacts on gas infrastructure and estimates the changes in end-user methane price considering a business-as-usual and an optimised infrastructure pathway. Our results show that gas supply and demand radically change by mid-century across various scenarios. Moreover the analysis suggests that deep transformations of the gas infrastructure are required and that according to the existing pricing mechanisms the end-user price of methane will increase driven by the switch to low-carbon gases and intensified by infrastructure costs.
Sizing of a Fuel Cell–battery Backup System for a University Building Based on the Probability of the Power Outages Length
Jul 2022
Publication
Hydrogen is a bright energy vector that could be crucial to decarbonise and combat climate change. This energy evolution involves several sectors including power backup systems to supply priority facility loads during power outages. As buildings now integrate complex automation domotics and security systems energy backup systems cause interest. A hydrogen-based backup system could supply loads in a multi-day blackout; however the backup system should be sized appropriately to ensure the survival of essential loads and low cost. In this sense this work proposes a sizing of fuel cell (FC) backup systems for low voltage (LV) buildings using the history of power outages. Historical data allows fitting a probability function to determine the appropriate survival of loads. The proposed sizing is applied to a university building with a photovoltaic generation system as a case study. Results show that the sizing of an FC–battery backup system for the installation is 7.6% cheaper than a battery-only system under a usual 330-minutes outage scenario. And 59.3% cheaper in the case of an unusual 48-hours outage scenario. It ensures a 99% probability of supplying essential load during power outages. It evidences the pertinence of an FC backup system to attend to outages of long-duration and the integration of batteries to support the abrupt load variations. This research is highlighted by using historical data from actual outages to define the survival of essential loads with total service probability. It also makes it possible to determine adequate survival for non-priority loads. The proposed sizing is generalisable and scalable for other buildings and allows quantifying the reliability of the backup system tending to the resilience of electrical systems.
The Vision of France, Germany, and the European Union on Future Hydrogen Energy Research and Innovation
Jul 2021
Publication
Hydrogen (H2) is an essential vector for freeing our societies from fossil fuels and effectively initiating the energy transition. Offering high energy density hydrogen can be used for mobile stationary or industrial applications of all sizes. This perspective on the crucial role of hydrogen is shared by a growing number of countries worldwide (e.g. China Germany Japan Republic of Korea Australia and United States) which are publishing ambitious roadmaps for the development of hydrogen and fuel cell technologies supported by substantial financial efforts.
Combustion Regimes of Hydrogen-air-steam Mixtures
Sep 2021
Publication
In the case of a severe nuclear power plant accident hydrogen gas formation may occur from the core degradation and cooling water evaporation and subsequent oxidation of zircaloy. These phenomena increase the risk of hazardous combustion events in the reactor especially when combined with an ignition source. If not handled carefully these types of accidents can cause severe damage to the reactor building with potential radioactive effects on the environment. Although hydrogen-air combustion has been investigated before hydrogen-air-steam mixtures remain unstudied under reactor-like conditions. Thus this study investigated such mixtures’ combustion regimes. A closed tube of 318 liters (7.65m tall and 0.23m inner diameter) measures the flame speed flame propagation and shock wave behaviors for 11-15 %vol hydrogen mixtures combined with 0 20 or 30 %vol steam and air. Thus both the effect of steam and hydrogen content was investigated and compared. The experimental setup combined photomultiplier tubes pressure sensors and shock detectors to give a full view of the different combustion regimes. A number of obstacles changed the in-chamber turbulence during flame propagation to provide further reactor-like environments. This changed turbulence affected the combustion regimes and enhanced the flame speed for some cases. The results showed varying combustion behaviors depending on the water vapor concentration where a higher concentration meant a lower flame speed reduced pressure load and sometimes combustion extinction. At 0 %vol steam dilution the flame speed remained supersonic for all H2 concentrations while at 30 %vol steam dilution the flame speed remained subsonic for all H2 concentrations. Thus with high levels of steam dilution the risk for shock waves leading to potential reactor building destruction decreases."
Hydrogen Energy Storage: New Techno-economic Emergence Solution Analysis
Aug 2015
Publication
The integration of various renewable energy sources as well as the liberalization of electricity markets are established facts in modern electrical power systems. The increased share of renewable sources within power systems intensifies the supply variability and intermittency. Therefore energy storage is deemed as one of the solutions for stabilizing the supply of electricity to maintain generation-demand balance and to guarantee uninterrupted supply of energy to users. In the context of sustainable development and energy resources depletion the question of the growth of renewable energy electricity production is highly linked to the ability to propose new and adapted energy storage solutions. The purpose of this multidisciplinary paper is to highlight the new hydrogen production and storage technology its efficiency and the impact of the policy context on its development. A comprehensive techno/socio/economic study of long term hydrogen based storage systems in electrical networks is addressed. The European policy concerning the different energy storage systems and hydrogen production is explicitly discussed. The state of the art of the techno-economic features of the hydrogen production and storage is introduced. Using Matlab-Simulink for a power system of rated 70 kW generator the excess produced hydrogen during high generation periods or low demand can be sold either directly to the grid owners or as filled hydrogen bottles. The affordable use of Hydrogen-based technologies for long term electricity storage is verified.
Improvement of SI Engine Combustion with Ammonia as Fuel: Effect of Ammonia Dissociation Prior to Combustion
Mar 2022
Publication
Although recent studies have shown the possibility of running ‘standard’ spark-ignition engines with 6 pure ammonia the operating range remains limited mainly due to the unfavorable characteristics of 7 ammonia for premixed combustion and often requires the addition of a complementary fuel such as H2 8 to extend it. As the best way to add H2 is to crack ammonia directly on-board this paper focuses on 9 the impact of the upstream cracking level of ammonia on the performance and emissions of a single 10 cylinder spark ignition engine. Experiments were performed over several equivalence ratios 11 dissociation rates and load conditions. It is confirmed that only a slight rate of ammonia dissociation 12 (10%) upstream of the combustion considerably enhances the engine's operating range thanks to a 13 better combustion stability. In terms of pollutant emissions the partial dissociation of ammonia 14 especially for slightly lean mixtures induces a very clear trade-off between high NOx and high 15 unburned ammonia level for high and low ammonia dissociation rates respectively. Therefore 16 cracking NH3 does not only improve the operating range of ammonia-fueled spark ignition engines but 17 can also help to reduce NH3. However to reach the same engine output work higher ammonia fuel 18 consumption will be necessary since the global system efficiency is lower using fuel dissociation. In 19 addition the global warming effect is increased with dissociation level since a higher level of N2O is 20 generated by the hydrogen contribution.
Optimal Multi-layer Economical Schedule for Coordinated Multiple Mode Operation of Wind-solar Microgrids with Hybrid Energy Storage Systems
Nov 2023
Publication
The aim of this paper is the design and implementation of an advanced model predictive control (MPC) strategy for the management of a wind–solar microgrid (MG) both in the islanded and grid-connected modes. The MG includes energy storage systems (ESSs) and interacts with external hydrogen and electricity consumers as an extra feature. The system participates in two different electricity markets i.e. the daily and real-time markets characterized by different time-scales. Thus a high-layer control (HLC) and a low-layer control (LLC) are developed for the daily market and the real-time market respectively. The sporadic characteristics of renewable energy sources and the variations in load demand are also briefly discussed by proposing a controller based on the stochastic MPC approach. Numerical simulations with real wind and solar generation profiles and spot prices show that the proposed controller optimally manages the ESSs even when there is a deviation between the predicted scenario determined at the HLC and the real-time one managed by the LLC. Finally the strategy is tested on a lab-scale MG set up at Khalifa University Abu Dhabi UAE.
Expert Perceptions of Game-changing Innovations towards Net Zero
Dec 2022
Publication
Current technological improvements are yet to put the world on track to net-zero which will require the uptake of transformative low-carbon innovations to supplement mitigation efforts. However the role of such innovations is not yet fully understood; some of these ‘miracles’ are considered indispensable to Paris Agreement-compliant mitigation but their limitations availability and potential remain a source of debate. We evaluate such potentially game-changing innovations from the experts’ perspective aiming to support the design of realistic decarbonisation scenarios and better-informed net-zero policy strategies. In a worldwide survey 260 climate and energy experts assessed transformative innovations against their mitigation potential at-scale availability and/or widescale adoption and risk of delayed diffusion. Hierarchical clustering and multi-criteria decision-making revealed differences in perceptions of core technological innovations with next generation energy storage alternative building materials iron-ore electrolysis and hydrogen in steelmaking emerging as top priorities. Instead technologies highly represented in well-below-2◦C scenarios seemingly feature considerable and impactful delays hinting at the need to re-evaluate their role in future pathways. Experts’ assessments appear to converge more on the potential role of other disruptive innovations including lifestyle shifts and alternative economic models indicating the importance of scenarios including non-technological and demand-side innovations. To provide insights for expert elicitation processes we finally note caveats related to the level of representativeness among the 260 engaged experts the level of their expertise that may have varied across the examined innovations and the potential for subjective interpretation to which the employed linguistic scales may be prone to.
An Insight into Underground Hydrogen Storage in Italy
Apr 2023
Publication
Hydrogen is a key energy carrier that could play a crucial role in the transition to a low-carbon economy. Hydrogen-related technologies are considered flexible solutions to support the large-scale implementation of intermittent energy supply from renewable sources by using renewable energy to generate green hydrogen during periods of low demand. Therefore a short-term increase in demand for hydrogen as an energy carrier and an increase in hydrogen production are expected to drive demand for large-scale storage facilities to ensure continuous availability. Owing to the large potential available storage space underground hydrogen storage offers a viable solution for the long-term storage of large amounts of energy. This study presents the results of a survey of potential underground hydrogen storage sites in Italy carried out within the H2020 EU Hystories “Hydrogen Storage In European Subsurface” project. The objective of this work was to clarify the feasibility of the implementation of large-scale storage of green hydrogen in depleted hydrocarbon fields and saline aquifers. By analysing publicly available data mainly well stratigraphy and logs we were able to identify onshore and offshore storage sites in Italy. The hydrogen storage capacity in depleted gas fields currently used for natural gas storage was estimated to be around 69.2 TWh.
Review on Ammonia as a Potential Fuel: From Synthesis to Economics
Feb 2021
Publication
Ammonia a molecule that is gaining more interest as a fueling vector has been considered as a candidate to power transport produce energy and support heating applications for decades. However the particular characteristics of the molecule always made it a chemical with low if any benefit once compared to conventional fossil fuels. Still the current need to decarbonize our economy makes the search of new methods crucial to use chemicals such as ammonia that can be produced and employed without incurring in the emission of carbon oxides. Therefore current efforts in this field are leading scientists industries and governments to seriously invest efforts in the development of holistic solutions capable of making ammonia a viable fuel for the transition toward a clean future. On that basis this review has approached the subject gathering inputs from scientists actively working on the topic. The review starts from the importance of ammonia as an energy vector moving through all of the steps in the production distribution utilization safety legal considerations and economic aspects of the use of such a molecule to support the future energy mix. Fundamentals of combustion and practical cases for the recovery of energy of ammonia are also addressed thus providing a complete view of what potentially could become a vector of crucial importance to the mitigation of carbon emissions. Different from other works this review seeks to provide a holistic perspective of ammonia as a chemical that presents benefits and constraints for storing energy from sustainable sources. State-of-the-art knowledge provided by academics actively engaged with the topic at various fronts also enables a clear vision of the progress in each of the branches of ammonia as an energy carrier. Further the fundamental boundaries of the use of the molecule are expanded to real technical issues for all potential technologies capable of using it for energy purposes legal barriers that will be faced to achieve its deployment safety and environmental considerations that impose a critical aspect for acceptance and wellbeing and economic implications for the use of ammonia across all aspects approached for the production and implementation of this chemical as a fueling source. Herein this work sets the principles research practicalities and future views of a transition toward a future where ammonia will be a major energy player.
A Comparative Study on Energy Efficiency of the Maritime Supply Chains for Liquefied Hydrogen, Ammonia, Methanol and Natural Gas
Jun 2023
Publication
To cope with climate change emerging fuels- hydrogen ammonia and methanol- have been proposed as promising energy carriers that will replace part of the liquefied natural gas (LNG) in future maritime scenarios. Energy efficiency is an important indicator for evaluating the system but the maritime supply system for emerging fuels has yet to be revealed. In this study the energy efficiency of the maritime supply chain of hydrogen ammonia methanol and natural gas is investigated considering processes including production storage loading transport and unloading. A sensitivity analysis of parameters such as ambient temperature storage time pipeline length and sailing time is also carried out. The results show that hydrogen (2.366%) has the highest daily boil-off gas (BOG) rate and wastes more energy than LNG (0.413%) with ammonia and methanol both being lower than LNG. The recycling of BOG is of great importance to the hydrogen supply chain. When produced from renewable energy sources methanol (98.02%) is the most energy efficient followed by ammonia with hydrogen being the least (89.10%). This assessment shows from an energy efficiency perspective that ammonia and methanol have the potential to replace LNG as the energy carrier of the future and that hydrogen requires efficient BOG handling systems to increase competitiveness. This study provides some inspirations for the design of global maritime supply systems for emerging fuels.
Assessing and Modelling Hydrogen Reactivity in Underground Hydrogen Storage: A Review and Models Simulating the Lobodice Town Gas Storage
Apr 2023
Publication
Underground Hydrogen storage (UHS) is a promising technology for safe storage of large quantities of hydrogen in daily to seasonal cycles depending on the consumption requirements. The development of UHS requires anticipating hydrogen behavior to prevent any unexpected economic or environmental impact. An open question is the hydrogen reactivity in underground porous media storages. Indeed there is no consensus on the effects or lack of geochemical reactions in UHS operations because of the strong coupling with the activity of microbes using hydrogen as electron donor during anaerobic reduction reactions. In this work we apply different geochemical models to abiotic conditions or including the catalytic effect of bacterial activity in methanogenesis acetogenesis and sulfate-reduction reactions. The models are applied to Lobodice town gas storage (Czech Republic) where a conversion of hydrogen to methane was measured during seasonal gas storage. Under abiotic conditions no reaction is simulated. When the classical thermodynamic approach for aqueous redox reactions is applied the simulated reactivity of hydrogen is too high. The proper way to simulate hydrogen reactivity must include a description of the kinetics of the aqueous redox reactions. Two models are applied to simulate the reactions of hydrogen observed at Lobodice gas storage. One modeling the microbial activity by applying energy threshold limitations and another where microbial activity follows a Monod-type rate law. After successfully calibrating the bio-geochemical models for hydrogen reactivity on existing gas storage data and constraining the conditions where microbial activity will inhibit or enhance hydrogen reactivity we now have a higher confidence in assessing the hydrogen reactivity in future UHS in aquifers or depleted reservoirs.
Renewable Hydrogen Production Processes for the Off-Gas Valorization in Integrated Steelworks through Hydrogen Intensified Methane and Methanol Syntheses
Nov 2020
Publication
Within integrated steelmaking industries significant research efforts are devoted to the efficient use of resources and the reduction of CO2 emissions. Integrated steelworks consume a considerable quantity of raw materials and produce a high amount of by-products such as off-gases currently used for the internal production of heat steam or electricity. These off-gases can be further valorized as feedstock for methane and methanol syntheses but their hydrogen content is often inadequate to reach high conversions in synthesis processes. The addition of hydrogen is fundamental and a suitable hydrogen production process must be selected to obtain advantages in process economy and sustainability. This paper presents a comparative analysis of different hydrogen production processes from renewable energy namely polymer electrolyte membrane electrolysis solid oxide electrolyze cell electrolysis and biomass gasification. Aspen Plus® V11-based models were developed and simulations were conducted for sensitivity analyses to acquire useful information related to the process behavior. Advantages and disadvantages for each considered process were highlighted. In addition the integration of the analyzed hydrogen production methods with methane and methanol syntheses is analyzed through further Aspen Plus®-based simulations. The pros and cons of the different hydrogen production options coupled with methane and methanol syntheses included in steelmaking industries are analyzed
Identifying Social Aspect Related to the Hydrogen Economy: Review, Synthesis, and Research Perspectives
Oct 2023
Publication
Energy transition will reshape the power sector and hydrogen is a key energy carrier that could contribute to energy security. The inclusion of sustainability criteria is crucial for the adequate design/deployment of resilient hydrogen networks. While cost and environmental metrics are commonly included in hydrogen models social aspects are rarely considered. This paper aims to identify the social criteria related to the hydrogen economy by using a systematic hybrid literature review. The main contribution is the identification of twelve social aspects which are described ranked and discussed. “Accessibility” “Information” “H2 markets” and “Acceptability” are now emerging as the main themes of hydrogen-related social research. Identified gaps are e.g. lack of the definition of the value of H2 for society insufficient research for “socio-political” aspects (e.g. geopolitics wellbeing) scarce application of social lifecycle assessment and the low amount of works with a focus on social practices and cultural issues.
Hydrogen Refuelling Station Calibration with a Traceable Gravimetric Standard
Apr 2020
Publication
Of all the alternatives to hydrocarbon fuels hydrogen offers the greatest long-term potential to radically reduce the many problems inherent in fuel used for transportation. Hydrogen vehicles have zero tailpipe emissions and are very efficient. If the hydrogen is made from renewable sources such as nuclear power or fossil sources with carbon emissions captured and sequestered hydrogen use on a global scale would produce almost zero greenhouse gas emissions and greatly reduce air pollutant emissions. The aim of this work is to realise a traceability chain for hydrogen flow metering in the range typical for fuelling applications in a wide pressure range with pressures up to 875 bar (for Hydrogen Refuelling Station - HRS with Nominal Working Pressure of 700 bar) and temperature changes from −40 °C (pre-cooling) to 85 °C (maximum allowed vehicle tank temperature) in accordance with the worldwide accepted standard SAE J2601. Several HRS have been tested in Europe (France Netherlands and Germany) and the results show a good repeatability for all tests. This demonstrates that the testing equipment works well in real conditions. Depending on the installation configuration some systematic errors have been detected and explained. Errors observed for Configuration 1 stations can be explained by pressure differences at the beginning and end of fueling in the piping between the Coriolis Flow Meter (CFM) and the dispenser: the longer the distance the bigger the errors. For Configuration 2 where this distance is very short the error is negligible.
THyGA - Roadmap H2NG for Europe
May 2023
Publication
This report aims at summarizing the different stakeholders’ opinions on H2NG blends and cross them with the THyGA results to recommend some necessary actions to prepare the field for operational large-scale blending (liability delayed ignition adjustment…).
THyGA - Long Term Effect of H2 on Appliances Tested
May 2023
Publication
The goals of the long-term tests were to see the impact of blends of hydrogen and natural gas on the technical condition of the appliances and their performance after several hours of operation. To do so they were run through an accelerated test program amounting to more than 3000 testing hours for the boilers and more than 2500 testing hours for the cookers. The percentage of hydrogen in the test gas was 30% by volume. Three boilers and two cookers were tested by DGC and two boilers by GWI. This report describes the test protocol the results and analysis on the seven appliances tested.
Climate Change Impacts on Gaseous Hydrogen (H2) Potential Produced by Photovoltaic Electrolysis for Stand-Alone or Grid Applications in Europe
Dec 2022
Publication
The EU’s hydrogen strategy consists of studying the potential for renewable hydrogen to help decarbonize the EU in a cost-effective way. Today hydrogen accounts for less than 2% of Europe’s energy consumption. It is primarily used to produce chemical products. However 96% of this hydrogen production is through natural gas leading to significant amounts of CO2 emissions. In this paper we investigated PV electrolysis H2 gas (noted H2(g)) production for mapping this resource at Europe’s scale. The Cordex/Copernicus RCPs scenarios allow for evaluating the impact of climate changes on the H2 -produced mass and the equivalent energy according to both extreme RCPs scenarios. New linear regressions are investigated to study the great dependence in H2(g) produced masses (kg·yr−1 ) and equivalent energies (MWh·yr−1 ) for European countries. Computational scenarios are investigated from a reference year (2005) to the end of the century (2100) by steps of 5 years. According to RCPs 2.6 (favorable)/8.5 (extreme) 31.7% and 77.4% of Europe’s area presents a decrease of H2(g)-produced masses between 2005 and 2100. For the unfavorable scenario (8.5) only a few regions located in the northeast of France Germany Austria Romania Bulgaria and Greece present a positive balance in H2(g) production for supplying remote houses or smart grids in electricity and heat energy.
Discharge Modeling of Large Scale LH2 Experiments with an Engineering Tool
Sep 2021
Publication
Accurate estimation of mass flow rate and release conditions is important for the design of dispersion and combustion experiments for the subsequent validation of CFD codes/models for consequence assessment analysis within related risk assessment studies and for associated Regulation Codes and Standards development. This work focuses on the modelling of the discharge phase of the recent large scale LH2 release and dispersion experiments performed by HSE within the framework of PRESLHY project. The experimental conditions covered sub-cooled liquid stagnation conditions at two pressures (2 and 6 bara) and 3 release nozzle diameters (1 ½ and ¼ inches). The simulations were performed using a 1d engineering tool which accounts for discharge line effects due to friction extra resistance due to fittings and area change. The engineering tool uses the Possible Impossible Flow (PIF) algorithm for choked flow calculations and the Helmholtz Free Energy (HFE) EoS formulation. Three different phase distribution models were applied. The predictions are compared against measured and derived data from the experiments and recommendations are given both regarding engineering tool applicability and future experimental design.
Review and Survey of Methods for Analysis of Impurities in Hydrogen for Fuel Cell Vehicles According to ISO 14687:2019
Feb 2021
Publication
Gaseous hydrogen for fuel cell electric vehicles must meet quality standards such as ISO 14687:2019 which contains maximal control thresholds for several impurities which could damage the fuel cells or the infrastructure. A review of analytical techniques for impurities analysis has already been carried out by Murugan et al. in 2014. Similarly this document intends to review the sampling of hydrogen and the available analytical methods together with a survey of laboratories performing the analysis of hydrogen about the techniques being used. Most impurities are addressed however some of them are challenging especially the halogenated compounds since only some halogenated compounds are covered not all of them. The analysis of impurities following ISO 14687:2019 remains expensive and complex enhancing the need for further research in this area. Novel and promising analyzers have been developed which need to be validated according to ISO 21087:2019 requirements.
THyGA - Test Report on Mitigation Solutions for Residential Natural Gas Appliances Not Designed for Hydrogen Admixture
Apr 2023
Publication
This report from the WP5 “Mitigation” provides information and test results regarding perturbations that hydrogen could cause to gas appliances when blended to natural gas especially on anatural draught for exhaust fumes or acidity for the condensates. The important topic of on-site adjustment is also studied with test results on alternative technologies and proposals of mitigation approaches.
The Fuel Flexibility of Gas Turbines: A Review and Retrospective Outlook
May 2023
Publication
Land-based gas turbines (GTs) are continuous-flow engines that run with permanent flames once started and at stationary pressure temperature and flows at stabilized load. Combustors operate without any moving parts and their substantial air excess enables complete combustion. These features provide significant space for designing efficient and versatile combustion systems. In particular as heavy-duty gas turbines have moderate compression ratios and ample stall margins they can burn not only high- and medium-BTU fuels but also low-BTU ones. As a result these machines have gained remarkable fuel flexibility. Dry Low Emissions combustors which were initially confined to burning standard natural gas have been gradually adapted to an increasing number of alternative gaseous fuels. The paper first delivers essential technical considerations that underlie this important fuel portfolio. It then reviews the spectrum of alternative GT fuels which currently extends from lean gases (coal bed coke oven blast furnace gases . . . ) to rich refinery streams (LPG olefins) and from volatile liquids (naphtha) to heavy hydrocarbons. This “fuel diet” also includes biogenic products (biogas biodiesel and ethanol) and especially blended and pure hydrogen the fuel of the future. The paper also outlines how historically land-based GTs have gradually gained new fuel territories thanks to continuous engineering work lab testing experience extrapolation and validation on the field.
Natural Hydrogen the Fuel of the 21st Century
Jun 2019
Publication
Much has been learned about natural hydrogen (H2) seepages and accumulation but present knowledge of hydrogen behavior in the crust is so limited that it is not yet possible to consider exploitation of this resources. Hydrogen targeting requires a shift in the long-standing paradigms that drive oil and gas exploration. This paper describes the foundation of an integrated source-to-sink view of the hydrogen cycle and propose preliminary practical guidelines for hydrogen exploration.
Proton Exchange Membrane Electrolyzer Modeling for Power Electronics Control: A Short Review
May 2020
Publication
The main purpose of this article is to provide a short review of proton exchange membrane electrolyzer (PEMEL) modeling used for power electronics control. So far three types of PEMEL modeling have been adopted in the literature: resistive load static load (including an equivalent resistance series-connected with a DC voltage generator representing the reversible voltage) and dynamic load (taking into consideration the dynamics both at the anode and the cathode). The modeling of the load is crucial for control purposes since it may have an impact on the performance of the system. This article aims at providing essential information and comparing the different load modeling.
Techno-Economic Potential of Wind-Based Green Hydrogen Production in Djibouti: Literature Review and Case Studies
Aug 2023
Publication
Disputed supply chains inappropriate weather and low investment followed by the Russian invasion of Ukraine has led to a phenomenal energy crisis especially in the Horn of Africa. Accordingly proposing eco-friendly and sustainable solutions to diversify the access of electricity in the Republic of Djibouti which has no conventional energy resources and is completely energy dependent on its neighboring countries has become a must. Therefore the implementation of sustainable renewable and energy storage systems is nationally prioritized. This paper deals for the first time with the exploitation of such an affordable and carbon-free resource to produce hydrogen from wind energy in the rural areas of Nagad and Bara Wein in Djibouti. The production of hydrogen and the relevant CO2 emission reduction using different De Wind D6 Vestas and Nordex wind turbines are displayed while using Alkaline and Proton Exchange Membrane (PEM) electrolyzers. The Bara Wein and Nagad sites had a monthly wind speed above 7 m/s. From the results the Nordex turbine accompanied with the alkaline electrolyzer provides the most affordable electricity production approximately 0.0032 $/kWh for both sites; this cost is about one per hundred the actual imported hydroelectric energy price. Through the ecological analysis the Nordex turbine is the most suitable wind turbine with a CO2 emission reduction of 363.58 tons for Bara Wein compared to 228.76 tons for Nagad. While integrating the initial cost of wind turbine implementation in the capital investment the mass and the levelized cost of the produced green hydrogen are estimated as (29.68 tons and 11.48 $/kg) for Bara Wein with corresponding values of (18.68 tons and 18.25 $/kg) for Nagad.
Hydrogen Fuel Cell as an Electric Generator: A Case Study for a General Cargo Ship
Feb 2024
Publication
In this study real voyage data and ship specifications of a general cargo ship are employed and it is assumed that diesel generators are replaced with hydrogen proton exchange membrane fuel cells. The effect of the replacement on CO2 NOX SOX and PM emissions and the CII value is calculated. Emission calculations show that there is a significant reduction in emissions when hydrogen fuel cells are used instead of diesel generators on the case ship. By using hydrogen fuel cells there is a 37.4% reduction in CO2 emissions 32.5% in NOX emissions 37.3% in SOX emissions and 37.4% in PM emissions. If hydrogen fuel cells are not used instead of diesel generators the ship will receive an A rating between 2023 and 2026 a B rating in 2027 a C rating in 2028–2029 and an E rating in 2030. On the other hand if hydrogen fuel cells are used the ship will always remain at an A rating between 2023 and 2030. The capital expenditure (CAPEX) and operational expenditure (OPEX) of the fuel cell system are USD 1305720 and USD 2470320 respectively for a 15-year lifetime and the hydrogen fuel expenses are competitive at USD 260981 while marine diesel oil (MDO) fuel expenses are USD 206435.
Decarbonization with Induced Technical Change: Exploring the Niche Potential of Hydrogen in Heavy Transportation
Jan 2024
Publication
Fuel cells and electric batteries are competing technologies for the energy transition in heavy transportation. We explore the conditions for the survival of a unique technology in the long term. Learning by doing suggests focusing on a single technology while differentiation and decreasing return to scale (cost convexity) favor diversification. Exogenous technical change also plays a role. The interaction between these factors is analyzed in a general model. It is proved that in absence of convexity and exogenous technical change only one technology is used for the whole transition. We then apply this framework to analyze the competition between fuel-cell electric buses (FCEBs) and battery electric buses (BEB) in the European bus sector. There are both learning by doing and exogenous technical change. The model is calibrated and solved. It is shown that the existence of a niche for FCEBs critically depends on the speed at which cost reductions are achieved. The speed depends both on the size of the niche and the rate of learning by doing for FCEBs. Public policies to decentralize the socially optimal trajectory in terms of taxes (carbon) and subsidies (learning by doing) are derived.
Comparison of Battery Electric Vehicles and Fuel Cell Vehicles
Sep 2023
Publication
In the current context of the ban on fossil fuel vehicles (diesel and petrol) adopted by several European cities the question arises of the development of the infrastructure for the distribution of alternative energies namely hydrogen (for fuel cell electric vehicles) and electricity (for battery electric vehicles). First we compare the main advantages/constraints of the two alternative propulsion modes for the user. The main advantages of hydrogen vehicles are autonomy and fast recharging. The main advantages of battery-powered vehicles are the lower price and the wide availability of the electricity grid. We then review the existing studies on the deployment of new hydrogen distribution networks and compare the deployment costs of hydrogen and electricity distribution networks. Finally we conclude with some personal conclusions on the benefits of developing both modes and ideas for future studies on the subject.
Hydrogen Storage as a Key Energy Vector for Car Transportation: A Tutorial Review
Oct 2023
Publication
Hydrogen storage is a key enabling technology for the extensive use of hydrogen as energy carrier. This is particularly true in the widespread introduction of hydrogen in car transportation. Indeed one of the greatest technological barriers for such development is an efficient and safe storage method. So in this tutorial review the existing hydrogen storage technologies are described with a special emphasis on hydrogen storage in hydrogen cars: the current and the ongoing solutions. A particular focus is given on solid storage and some of the recent advances on plasma hydrogen ion implantation which should allow not only the preparation of metal hydrides but also the imagination of a new refluing circuit. From hydrogen discovery to its use as an energy vector in cars this review wants to be as exhaustive as possible introducing the basics of hydrogen storage and discussing the experimental practicalities of car hydrogen fuel. It wants to serve as a guide for anyone wanting to undertake such a technology and to equip the reader with an advanced knowledge on hydrogen storage and hydrogen storage in hydrogen cars to stimulate further researches and yet more innovative applications for this highly interesting field.
Hydrogen Fuel Quality from Two Main Production Processes: Steam Methane Reforming and Proton Exchange Membrane Water Electrolysis
Oct 2019
Publication
Thomas Bacquart,
Karine Arrhenius,
Stefan Persijn,
Andrés Rojo,
Fabien Auprêtre,
Bruno Gozlan,
Abigail Morris,
Andreas Fischer,
Arul Murugan,
Sam Bartlett,
Niamh Moore,
Guillaume Doucet,
François Laridant,
Eric Gernot,
Teresa E. Fernandez,
Concepcion Gomez,
Martine Carré,
Guy De Reals and
Frédérique Haloua
The absence of contaminants in the hydrogen delivered at the hydrogen refuelling station is critical to ensure the length life of FCEV. Hydrogen quality has to be ensured according to the two international standards ISO 14687–2:2012 and ISO/DIS 19880-8. Amount fraction of contaminants from the two hydrogen production processes steam methane reforming and PEM water electrolyser is not clearly documented. Twenty five different hydrogen samples were taken and analysed for all contaminants listed in ISO 14687-2. The first results of hydrogen quality from production processes: PEM water electrolysis with TSA and SMR with PSA are presented. The results on more than 16 different plants or occasions demonstrated that in all cases the 13 compounds listed in ISO 14687 were below the threshold of the international standards. Several contaminated hydrogen samples demonstrated the needs for validated and standardised sampling system and procedure. The results validated the probability of contaminants presence proposed in ISO/DIS 19880-8. It will support the implementation of ISO/ DIS 19880-8 and the development of hydrogen quality control monitoring plan. It is recommended to extend the study to other production method (i.e. alkaline electrolysis) the HRS supply chain (i.e. compressor) to support the technology growth.
Large-Scale Hydrogen Production Systems Using Marine Renewable Energies: State-of-the-Art
Dec 2023
Publication
To achieve a more ecologically friendly energy transition by the year 2050 under the European “green” accord hydrogen has recently gained significant scientific interest due to its efficiency as an energy carrier. This paper focuses on large-scale hydrogen production systems based on marine renewable-energy-based wind turbines and tidal turbines. The paper reviews the different technologies of hydrogen production using water electrolyzers energy storage unit base hydrogen vectors and fuel cells (FC). The focus is on large-scale hydrogen production systems using marine renewable energies. This study compares electrolyzers energy storage units and FC technologies with the main factors considered being cost sustainability and efficiency. Furthermore a review of aging models of electrolyzers and FCs based on electrical circuit models is drawn from the literature and presented including characterization methods of the model components and the parameters extraction methods using a dynamic current profile. In addition industrial projects for producing hydrogen from renewable energies that have already been completed or are now in progress are examined. The paper is concluded through a summary of recent hydrogen production and energy storage advances as well as some applications. Perspectives on enhancing the sustainability and efficiency of hydrogen production systems are also proposed and discussed. This paper provides a review of behavioral aging models of electrolyzers and FCs when integrated into hydrogen production systems as this is crucial for their successful deployment in an ever-changing energy context. We also review the EU’s potential for renewable energy analysis. In summary this study provides valuable information for research and industry stakeholders aiming to promote a sustainable and environmentally friendly energy transition.
Circular Economy for the Energy System as a Leverage for Low-carbon Transition: Long-Ter, Analysis of the Case of the South-East Region of France
Mar 2024
Publication
The circular economy is a decisive strategy for reconciling economic development and the environment. In France the CE was introduced into the law in 2015 with the objective of closing the loop. The legislation also delegates energy policy towards the French regions by granting them the jurisdiction to directly plan the energy–climate issues on their territory and to develop local energy resources. Thereby the SUD PACA region has redefined its objectives and targeted carbon neutrality and the transition to a CE by 2050. To study this transition we developed a TIMESPACA optimization model. The results show that following a CE perspective to develop a local energy system could contribute to reducing CO2 emissions by 50% in final energy consumption and reaching almost free electricity production. To obtain greater reductions the development of the regional energy systems should follow a careful policy design favoring the transition to low energy-consuming behavior and the strategical allocation of resources across the different sectors. Biomethane should be allocated to the buildings and industrial sector while hydrogen should be deployed for buses and freight transport vehicles.
No more items...