Poland
Investigation of Hydrogen Embrittlement Susceptibility and Fracture Toughness Drop after in situ Hydrogen Cathodic Charging for an X65 Pipeline Steel
Apr 2020
Publication
The present research focuses on the investigation of an in situ hydrogen charging effect during Crack Tip Opening Displacement testing (CTOD) on the fracture toughness properties of X65 pipeline steel. This grade of steel belongs to the broader category of High Strength Low Alloy Steels (HSLA) and its microstructure consists of equiaxed ferritic and bainitic grains with a low volume fraction of degenerated pearlite islands. The studied X65 steel specimens were extracted from pipes with 19.15 mm wall thickness. The fracture toughness parameters were determined after imposing the fatigue pre-cracked specimens on air on a specific electrolytic cell under a slow strain rate bending loading (according to ASTM G147-98 BS7448 and ISO12135 standards). Concerning the results of this study in the first phase the hydrogen cations’ penetration depth the diffusion coefficient of molecular and atomic hydrogen and the surficial density of blisters were determined. Next the characteristic parameters related to fracture toughness (such as J KQ CTODel CTODpl) were calculated by the aid of the Force-Crack Mouth Open Displacement curves and the relevant analytical equations.
The Influence of Refractory Metals on the Hydrogen Storage Characteristics of FeTi-based Alloys Prepared by Suspended Droplet Alloying
Jun 2020
Publication
The influence of the addition of refractory metals (molybdenum and tantalum) on the hydrogenation properties of FeTi intermetallic phase-based alloys was investigated. The suspended droplet alloying technique was applied to fabricate FeTiTa-based and FeTiMo-based alloys. The phase composition and hydrogen storage properties of the samples were investigated. The samples modified with the refractory metals exhibited lower plateau pressures and lower hydrogen storage capacities than those of the FeTi reference sample due to solid solution formation. It was observed that the equilibrium pressures decreased with the amount of molybdenum which is in good agreement with the increase in the cell parameters of the TiFe phase. Suspended droplet alloying was found to be a practical method to fabricate alloys with refractory metal additions; however it is appropriate for screening samples with desired chemical and phase compositions rather than for manufacturing purposes.
Hydrogen Explosion Hazards Limitation in Battery Rooms with Different Ventilation Systems
Sep 2019
Publication
When charging most types of industrial lead-acid batteries hydrogen gas is emitted. A large number of batteries especially in relatively small areas/enclosures and in the absence of an adequate ventilation system may create an explosion hazard. This paper describes full scale tests in confined space which demonstrate conditions that can occur in a battery room in the event of a ventilation system breakdown. Over the course of the tests full scale hydrogen emission experiments were performed to study emission time and flammable cloud formation according to the assumed emission velocity. On this basis the characteristics of dispersion of hydrogen in the battery room were obtained. The CFD model Fire Dynamic Simulator (NIST) was used for confirmation that the lack of ventilation in a battery room can be the cause of an explosive atmosphere developing and leading to a potential huge explosive hazard. It was demonstrated that different ventilation systems provide battery rooms with varying efficiencies of hydrogen removal. The most effective type appeared to be natural ventilation which proved more effective than mechanical means.
People’s Attitude to Energy from Hydrogen—From the Point of View of Modern Energy Technologies and Social Responsibility
Dec 2020
Publication
Energy from hydrogen is an appropriate technological choice in the context of sustainable development. The opportunities offered by the use of energy from hydrogen also represent a significant challenge for mobile technologies and daily life. Nevertheless despite a significant amount of research and information regarding the benefits of hydrogen energy it creates considerable controversy in many countries. Globally there is a lack of understanding about the production process of hydrogen energy and the benefits it provides which leads to concerns regarding the consistency of its use. In this study an original questionnaire was used as a research tool to determine the opinions of inhabitants of countries in which hydrogen energy is underutilized and where the infrastructure for hydrogen energy is underdeveloped. Respondents presented their attitude to ecology and indicated their knowledge regarding the operation of hydrogen energy and the use of hydrogen fuel. The results indicate that society is not convinced that the safety levels for energy derived from hydrogen are adequate. It can be concluded that knowledge about hydrogen as an energy source and the production safety and storage methods of hydrogen is very low. Negative attitudes to hydrogen energy can be an important barrier in the development of this energy in many countries.
A Review of Recent Advances on the Effects of Microstructural Refinement and Nano-Catalytic Additives on the Hydrogen Storage Properties of Metal and Complex Hydrides
Dec 2010
Publication
The recent advances on the effects of microstructural refinement and various nano-catalytic additives on the hydrogen storage properties of metal and complex hydrides obtained in the last few years in the allied laboratories at the University of Waterloo (Canada) and Military University of Technology (Warsaw Poland) are critically reviewed in this paper. The research results indicate that microstructural refinement (particle and grain size) induced by ball milling influences quite modestly the hydrogen storage properties of simple metal and complex metal hydrides. On the other hand the addition of nanometric elemental metals acting as potent catalysts and/or metal halide catalytic precursors brings about profound improvements in the hydrogen absorption/desorption kinetics for simple metal and complex metal hydrides alike. In general catalytic precursors react with the hydride matrix forming a metal salt and free nanometric or amorphous elemental metals/intermetallics which in turn act catalytically. However these catalysts change only kinetic properties i.e. the hydrogen absorption/desorption rate but they do not change thermodynamics (e.g. enthalpy change of hydrogen sorption reactions). It is shown that a complex metal hydride LiAlH4 after high energy ball milling with a nanometric Ni metal catalyst and/or MnCl2 catalytic precursor is able to desorb relatively large quantities of hydrogen at RT 40 and 80 °C. This kind of behavior is very encouraging for the future development of solid state hydrogen systems.
Residual Performance of Composite Pressure Vessels Submitted to Mechanical Impacts
Sep 2017
Publication
Type IV pressure vessels are commonly used for hydrogen on-board stationary or bulk storages. During their lifetime they can be submitted to mechanical impacts creating damage within the composite structure not necessarily correlated to what is visible from the outside. When an impact is suspected or when a cylinder is periodically inspected it is necessary to determine whether it can safely stay in service or not. The FCH JU project Hypactor aims at creating a large database of impacts characterized by various non destructive testing (NDT) methods in order to provide reliable pass-fail criteria for damaged cylinders. This paper presents some of the tests results investigating short term burst) and long term (cycling) performance of impacted cylinders and the recommendations that can be made for impact testing and NDT criteria calibration.
Investigation of Praseodymium and Samarium Co-doped Ceria as an Anode Catalyst for DIR-SOFC Fueled by Biogas
Aug 2020
Publication
The Pr and Sm co-doped ceria (with up to 20 mol.% of dopants) compounds were examined as catalytic layers on the surface of SOFC anode directly fed by biogas to increase a lifetime and the efficiency of commercially available DIR-SOFC without the usage of an external reformer.
The XRD SEM and EDX methods were used to investigate the structural properties and the composition of fabricated materials. Furthermore the electrical properties of SOFCs with catalytic layers deposited on the Ni-YSZ anode were examined by a current density-time and current density-voltage dependence measurements in hydrogen (24 h) and biogas (90 h). Composition of the outlet gasses was in situ analysed by the FTIR-based unit.
It has been found out that Ce0.9Sm0.1O2-δ and Ce0.8Pr0.05Sm0.15O2-δ catalytic layers show the highest stability over time and thus are the most attractive candidates as catalytic materials in comparison with other investigated lanthanide-doped ceria enhancing direct internal reforming of biogas in SOFCs.
The XRD SEM and EDX methods were used to investigate the structural properties and the composition of fabricated materials. Furthermore the electrical properties of SOFCs with catalytic layers deposited on the Ni-YSZ anode were examined by a current density-time and current density-voltage dependence measurements in hydrogen (24 h) and biogas (90 h). Composition of the outlet gasses was in situ analysed by the FTIR-based unit.
It has been found out that Ce0.9Sm0.1O2-δ and Ce0.8Pr0.05Sm0.15O2-δ catalytic layers show the highest stability over time and thus are the most attractive candidates as catalytic materials in comparison with other investigated lanthanide-doped ceria enhancing direct internal reforming of biogas in SOFCs.
Prospects for the Use of Hydrogen in the Armed Forces
Oct 2021
Publication
The energy security landscape that we envisage in 2050 will be different from that of today. Meeting the future energy needs of the armed forces will be a key challenge not least for military security. The World Energy Council’s World Energy Scenarios forecast that the world’s population will rise to 10 billion by 2050 which will also necessitate an increase in the size of the armed forces. In this context energy extraction distribution and storage become essential to stabilizing the imbalance between production and demand. Among the available solutions Power to Hydrogen (P2H) is one of the most appealing options. However despite the potential many obstacles currently hinder the development of the P2H market. This article aims to identify and analyse existing barriers to the introduction of P2H technologies that use hydrogen. The holistic approach used which was based on a literature survey identified obstacles and possible strategies for overcoming them. The research conducted presents an original research contribution at the level of hydrogen strategies considered in leading countries around the world. The research findings identified unresolved regulatory issues and sources of uncertainty in the armed forces. There is a lack of knowledge in the armed forces of some countries about the process of producing hydrogen energy and its benefits which raises concerns about the consistency of its exploitation. Negative attitudes towards hydrogen fuel energy can be a significant barrier to its deployment in the armed forces. Possible approaches and solutions have also been proposed to eliminate obstacles and to support decision makers in defining and implementing a strategy for hydrogen as a clean energy carrier. There are decisive and unresolved obstacles to its deployment not only in the armed forces
Studies of the Impact of Hydrogen on the Stability of Gaseous Mixtures of THT
Dec 2020
Publication
One of the most important requirements concerning the quality of natural gases guaranteeing their safe use involves providing the proper level of their odorization. This allows for the detection of uncontrolled leakages of gases from gas networks installations and devices. The concentration of an odorant should be adjusted in such a manner that the gas odor in a mixture with air would be noticeable by users (gas receivers). A permanent odor of gas is guaranteed by the stability of the odorant molecule and its resistance to changes in the composition of odorized gases. The article presents the results of experimental research on the impact of a hydrogen additive on the stability of tetrahydrothiophene (THT) mixtures in methane and in natural gas with a hydrogen additive. The objective of the work was to determine the readiness of measurement infrastructures routinely used in monitoring the process of odorizing natural gas for potential changes in its composition. One of the elements of this infrastructure includes the reference mixtures of THT used to verify the correctness of the readings of measurement devices. The performed experimental tests address possible changes in the composition of gases supplied via a distribution network resulting from the introduction of hydrogen. The lack of interaction between hydrogen and THT has been verified indirectly by assessing the stability of its mixtures with methane and natural gas containing hydrogen. The results of the presented tests permitted the identification of potential hazards for the safe use of gas from a distribution network resulting from changes in its composition caused by the addition of hydrogen.
Evaluation of Corrosion, Mechanical Properties and Hydrogen Embrittlement of Casing Pipe Steels with Different Microstructure
Dec 2021
Publication
In the research the corrosion and mechanical properties as well as susceptibility to hydrogen embrittlement of two casing pipe steels were investigated in order to assess their serviceability in corrosive and hydrogenating environments under operation in oil and gas wells. Two carbon steels with different microstructures were tested: the medium carbon steel (MCS) with bainitic microstructure and the medium-high carbon steel (MHCS) with ferrite–pearlite microstructure. The results showed that the corrosion resistance of the MHCS in CO2-containing acid chloride solution simulating formation water was significantly lower than that of the MCS which was associated with microstructure features. The higher strength MCS with the dispersed microstructure was less susceptible to hydrogen embrittlement under preliminary electrolytic hydrogenation than the lower strength MHCS with the coarse-grained microstructure. To estimate the embrittlement of steels the method of the FEM load simulation of the specimens with cracks was used. The constitutive relations of the true stress–strain of the tested steels were defined. The stress and strain dependences in the crack tip were calculated. It was found that the MHCS was characterized by the lower plasticity on the stage of the neck formation of the specimen and the lower fracture toughness than the other one. The obtained results demonstrating the limitations of the usage of casing pipes made of the MHCS with the coarse-grained ferrite/pearlite microstructure in corrosive and hydrogenating environments were discussed.
Varying Load Distribution Impacts on the Operation of a Hydrogen Generator Plant
Oct 2021
Publication
This study advances several methods to evaluate the operation of a hydrogen generator plant. The model developed helps customize plants that contain multiple generators of varying powers using a decision module which determines the most efficient plant load distribution. Evaluation indices to assess individual devices within the plant are proposed and system flexibility maximizes the amount of renewable energy stored. Three case studies examined the variable load distribution of an electrolysis system connected to a 40 MW wind farm for energy storage purposes and incorporated a “night-valley” operational strategy. These methods facilitate the selection of the proper plant configuration and provide estimates for individual device effectiveness within the system.
Hydrogen Embrittlement and Oxide Layer Effect in the Cathodically Charged Zircaloy-2
Apr 2020
Publication
Poland The present paper is aimed at determining the less investigated effects of hydrogen uptake on the microstructure and the mechanical behavior of the oxidized Zircaloy-2 alloy. The specimens were oxidized and charged with hydrogen. The different oxidation temperatures and cathodic current densities were applied. The scanning electron microscopy X-ray electron diffraction spectroscopy hydrogen absorption assessment tensile and nanoindentation tests were performed. At low oxidation temperatures an appearance of numerous hydrides and cracks and a slight change of mechanical properties were noticed. At high-temperature oxidation the oxide layer prevented the hydrogen deterioration of the alloy. For nonoxidized samples charged at different current density nanoindentation tests showed that both hardness and Young’s modulus revealed the minims at specific current value and the stepwise decrease in hardness during hydrogen desorption. The obtained results are explained by the barrier effect of the oxide layer against hydrogen uptake softening due to the interaction of hydrogen and dislocations nucleated by indentation test and hardening caused by the decomposition of hydrides. The last phenomena may appear together and result in hydrogen embrittlement in forms of simultaneous hydrogen-enhanced localized plasticity and delayed hydride cracking.
Assessment of Operational Degradation of Pipeline Steels
Jun 2021
Publication
This paper summarizes a series of the authors’ research in the field of assessing the operational degradation of oil and gas transit pipeline steels. Both mechanical and electrochemical properties of steels are deteriorated after operation as is their resistance to environmentally-assisted cracking. The characteristics of resistance to brittle fracture and stress corrosion cracking decrease most intensively which is associated with a development of in-bulk dissipated microdamages of the material. The most sensitive indicators of changes in the material’s state caused by degradation are impact toughness and fracture toughness by the J-integral method. The degradation degree of pipeline steels can also be evaluated nondestructively based on in-service changes in their polarization resistance and potential of the fracture surface. Attention is drawn to hydrogenation of a pipe wall from inside as a result of the electrochemical interaction of pipe metal with condensed moisture which facilitates operational degradation of steel due to the combined action of operating stresses and hydrogen. The development of microdamages along steel texture was evidenced metallographically as a trend to the selective etching of boundaries between adjacent bands of ferrite and pearlite and fractographically by revealing brittle fracture elements on the fracture surfaces namely delamination and cleavage indicating the sites of cohesion weakening between ferrite and pearlite bands. The state of the X52 steel in its initial state and after use for 30 years was assessed based on the numerical simulation method.
Effect of Hydrogen Addition on the Energetic and Ecologic Parameters of an SI Engine Fueled by Biogas
Jan 2021
Publication
The global policy solution seeks to reduce the usage of fossil fuels and greenhouse gas (GHG) emissions and biogas (BG) represents a solutions to these problems. The use of biogas could help cope with increased amounts of waste and reduce usage of fossil fuels. Biogas could be used in compressed natural gas (CNG) engines but the engine electronic control unit (ECU) needs to be modified. In this research a spark ignition (SI) engine was tested for mixtures of biogas and hydrogen (volumetric hydrogen concentration of 0 14 24 33 and 43%). In all experiments two cases of spark timing (ST) were used: the first for an optimal mixture and the second for CNG. The results show that hydrogen increases combustion quality and reduces incomplete combustion products. Because of BG’s lower burning speed the advanced ST increased brake thermal efficiency (BTE) by 4.3% when the engine was running on biogas. Adding 14 vol% of hydrogen (H2 ) increases the burning speed of the mixture and enhances BTE by 2.6% at spark timing optimal for CNG (CNG ST) and 0.6% at the optimal mixture ST (mixture ST). Analyses of the rate of heat release (ROHR) temperature and pressure increase in the cylinder were carried out using utility BURN in AVL BOOST software.
Validation of Selected Optical Methods for Assessing Polyethylene (PE) Liners Used in High Pressure Vessels for Hydrogen Storage
Jun 2021
Publication
A polyethylene (PE) liner is the basic element in high-pressure type 4 composite vessels designed for hydrogen or compressed natural gas (CNG) storage systems. Liner defects may result in the elimination of the whole vessel from use which is very expensive both at the manufacturing and exploitation stage. The goal is therefore the development of efficient non-destructive testing (NDT) methods to test a liner immediately after its manufacturing before applying a composite reinforcement. It should be noted that the current regulations codes and standards (RC&S) do not specify liner testing methods after manufacturing. It was considered especially important to find a way of locating and assessing the size of air bubbles and inclusions and the field of deformations in liner walls. It was also expected that these methods would be easily applicable to mass-produced liners. The paper proposes the use of three optical methods namely visual inspection digital image correlation (DIC) and optical fiber sensing based on Bragg gratings (FBG). Deformation measurements are validated with finite element analysis (FEA). The tested object was a prototype of a hydrogen liner for high-pressure storage (700 bar). The mentioned optical methods were used to identify defects and measure deformations.
A Hybrid Energy Storage System Using Compressed Air and Hydrogen as the Energy Carrier
Feb 2020
Publication
In this paper an innovative concept of an energy storage system that combines the idea of energy storage through the use of compressed air and the idea of energy storage through the use of hydrogen (with its further conversion to synthetic natural gas) has been proposed. The thermal integration of two sub-systems allows for efficient storage of large amounts of energy based on the use of pressure tanks with limited volumes. A thermodynamic assessment of the integrated hybrid system was carried out. For the assumed operation parameters an energy storage efficiency value of 38.15% was obtained which means the technology is competitive with intensively developed pure hydrogen energy storage technologies. The results obtained for the hybrid system were compared to the results obtained for three reference systems each of which uses hydrogen generators. The first is a typical Power-to-H2-to-Power system which integrates hydrogen generators with a fuel cell system. The other two additionally use a compressed air energy storage installation. In the first case the compressed air energy storage system consists of a diabatic system. In the second case the compressed air energy storage system is adiabatic. The article has discussed the disadvantages and advantages of all the analyzed systems.
Magnesium Gasar as a Potential Monolithic Hydrogen Absorbent
Feb 2021
Publication
The study focuses on the aspect of using the structure of gasars i.e. materials with directed open porosity as a potential hydrogen storage. The structure of the tested gasar is composed of a large number of thin open tubular pores running through the entire longitudinal section of the sample. This allows hydrogen to easily penetrate into the entire sample volume. The analysis of pore distribution showed that the longest diffusion path needed for full penetration of the metal structure with hydrogen is about L = 50–70 μm regardless of the external dimensions of the sample. Attempts to hydrogenate the magnesium gasar structure have shown its ability to accumulate hydrogen at a level of 1 wt%. The obtained results were compared with the best result was obtained for the ZK60 alloy after equal channel angular pressing (ECAP) and crushed to a powder form. The result obtained exceeded 4 wt% of hydrogen accumulated in the metal structure at theoretical 6.9 wt% maximum capacity. A model analysis of the theoretic absorption capacity of pure magnesium was also carried out based on the concentration of vacancies in the metal structure. The theoretical results obtained correlate well with experimental data.
The Energy Approach to the Evaluation of Hydrogen Effect on the Damage Accumulation
Aug 2019
Publication
The energy approach for determining the durability of structural elements at high temperature creep and hydrogen activity was proposed. It has been shown that the approach significantly simplifies research compared with the known ones. Approbation of the approach was carried out on the example of determining the indicators of durability of the Bridgman sample under conditions of creep and different levels of hydrogenation of the metal. It was shown that with an increase of hydrogen concentration in the metal from 2 to 10 ppm the durability of the test sample decreased from 22 to 58%.
Tests of the Vehicle’s Powertrain with Hydrogen Fuel Cells at a Low Temperature
Sep 2019
Publication
The article discusses issues related to the operation of fuel cells stack fed with hydrogen at low temperature. The test object was a Toyota Mirai passenger car equipped with this type of powertrain. Tests were carried out in a thermoclimatic chamber at the Cracow University of Technology. They had an initial character and their aim was to evaluate the work of individual subassemblies of the propulsion system including the hydrogen supply system in terms of operational safety.
Impact of Depth on Underground Hydrogen Storage Operations in Deep Aquifers
Mar 2024
Publication
Underground hydrogen storage in geological structures is considered appropriate for storing large amounts of hydrogen. Using the geological Konary structure in the deep saline aquifers an analysis of the influence of depth on hydrogen storage was carried out. Hydrogen injection and withdrawal modeling was performed using TOUGH2 software assuming different structure depths. Changes in the relevant parameters for the operation of an underground hydrogen storage facility including the amount of H2 injected in the initial filling period cushion gas working gas and average amount of extracted water are presented. The results showed that increasing the depth to approximately 1500 m positively affects hydrogen storage (flow rate of injected hydrogen total capacity and working gas). Below this depth the trend was reversed. The cushion gas-to-working gas ratio did not significantly change with increasing depth. Its magnitude depends on the length of the initial hydrogen filling period. An increase in the depth of hydrogen storage is associated with a greater amount of extracted water. Increasing the duration of the initial hydrogen filling period will reduce the water production but increase the cushion gas volume.
Hydrogen Storage in Pure and Boron-Substituted Nanoporous Carbons—Numerical and Experimental Perspective
Aug 2021
Publication
Nanoporous carbons remain the most promising candidates for effective hydrogen storage by physisorption in currently foreseen hydrogen-based scenarios of the world’s energy future. An optimal sorbent meeting the current technological requirement has not been developed yet. Here we first review the storage limitations of currently available nanoporous carbons then we discuss possible ways to improve their storage performance. We focus on two fundamental parameters determining the storage (the surface accessible for adsorption and hydrogen adsorption energy). We define numerically the values nanoporous carbons have to show to satisfy mobile application requirements at pressures lower than 120 bar. Possible necessary modifications of the topology and chemical compositions of carbon nanostructures are proposed and discussed. We indicate that pore wall fragmentation (nano-size graphene scaffolds) is a partial solution only and chemical modifications of the carbon pore walls are required. The positive effects (and their limits) of the carbon substitutions by B and Be atoms are described. The experimental ‘proof of concept’ of the proposed strategies is also presented. We show that boron substituted nanoporous carbons prepared by a simple arc-discharge technique show a hydrogen adsorption energy twice as high as their pure carbon analogs. These preliminary results justify the continuation of the joint experimental and numerical research effort in this field.
Laser Induced Hydrogen Emission from Ethanol with Dispersed Graphene Particles
Apr 2021
Publication
Efficient hydrogen emission from ethanol with disperse graphene foam particles by using a continuous wave infrared laser diode is reported. The products of ethanol dissociation - hydrogen methane and carbon oxide were measured using mass spectrometry. It was found that the most efficient generation of hydrogen was observed when graphene particles were irradiated by a focused laser beam proceeded at the surface of ethanol solution. The process was assisted by intense white light emission resulting from the laser induced multiphoton ionization of graphene combined with the simultaneous emission of hot electrons. The hot electron emission enables the efficient dissociation of ethanol molecules located close to the solution surface with graphene foam particles.
Inhibition of Hydrogen-yielding Dark Fermentation by Ascomycetous Yeasts
May 2018
Publication
Hydrogen-yielding fermentation conducted in bioreactors is an alternative method of hydrogen production. However unfavourable processes can seriously inhibit bio-hydrogen generation during the acidogenic step of anaerobic digestion. Here ascomycetous yeasts were identified as a major factor inhibiting the production of bio-hydrogen by fermentation. Changes in the performance of hydrogen-producing bioreactors including metabolic shift quantitative changes in the fermentation products decreased pH instability of the microbial community and consequently a dramatic drop in bio-hydrogen yield were observed following yeast infection. Ascomycetous yeasts from the genera Candida Kazachstania and Geotrichum were isolated from hydrogen-producing bioreactors. Yeast metabolites secreted into the growth medium showed antibacterial activity. Our studies indicate that yeast infection of hydrogen-producing microbial communities is one of the serious obstacles to use dark fermentation as an alternative method of bio-hydrogen production. It also explains why studies on hydrogen fermentation are still limited to the laboratory or pilot-scale systems.
Functional Model of Power Grid Stabilization in the Green Hydrogen Supply Chain System—Conceptual Assumptions
Dec 2022
Publication
Green hydrogen supply chain includes supply sources production and distribution of hydrogen produced from renewable energy sources (RES). It is a promising scientific and application area as it is related to the problem of instability of power grids supplied with RES. The article presents the conceptual assumptions of the research on the design of a functional multi-criteria model of the stabilization model architecture of energy distribution networks based on a hydrogen energy buffer taking into account the applicable use of hydrogen. The aim of the research was to identify the variables contributing to the stabilization of the operation of distribution networks. The method used to obtain this result was a systematic review of the literature using the technique of in-depth analysis of full-text articles and expert consultations. The concept of a functional model was described as a matrix in two dimensions in which the identified variables were embedded. The first dimension covers the phases of the supply chain: procurement and production along with storage and distribution. The second dimension divides the separate factors into technical economic and logistic. The research was conducted in the context of system optimization from the point of view of the operator of the energy distribution system. As a result of the research several benefits resulting from stabilization using a hydrogen buffer were identified. Furthermore the model may be used in designing solutions stabilizing the operation of power grids in which there are surpluses of electricity produced from RES. Due to the applied multidimensional approach the developed model is recommended for use as it enables the design of solutions in a systemic manner. Due to the growing level of energy obtained from renewable energy sources the issue of stabilizing the energy network is becoming increasingly important for energy network distributors.
Self-ignition of Hydrogen-nitrogen Mixtures During High-pressure Release Into Air
Oct 2015
Publication
This paper demonstrates experimental and numerical study on spontaneous ignition of H2–N2 mixtures during high-pressure release into air through the tubes of various diameters and lengths. The mixtures included 5% and 10% (vol.) N2 addition to hydrogen being at initial pressure in range of 4.3–15.9 MPa. As a point of reference pure hydrogen release experiments were performed with use of the same experimental stand experimental procedure and extension tubes. The results showed that N2 addition may increase the initial pressure necessary to self-ignite the mixture as much as 2.12 or 2.85 – times for 5% and 10% N2 addition respectively. Additionally simulations were performed with use of Cantera code (0-D) based on the ideal shock tube assumption and with the modified KIVA3V code (2-D) to establish the main factors responsible for ignition and sustained combustion during the release.
Hytunnel Project to Investigate the Use of Hydrogen Vehicles in Road Tunnels
Sep 2009
Publication
Hydrogen vehicles may emerge as a leading contender to replace today’s internal combustion engine powered vehicles. A Phenomena Identification and Ranking Table exercise conducted as part of the European Network of Excellence on Hydrogen Safety (HySafe) identified the use of hydrogen vehicles in road tunnels as a topic of important concern. An internal project called HyTunnel was duly established within HySafe to review identify and analyse the issues involved and to contribute to the wider activity to establish the true nature of the hazards posed by hydrogen vehicles in the confined space of a tunnel and their relative severity compared to those posed by vehicles powered by conventional fuels including compressed natural gas (CNG). In addition to reviewing current hydrogen vehicle designs tunnel design practice and previous research a programme of experiments and CFD modelling activities was performed for selected scenarios to examine the dispersion and explosion hazards potentially posed by hydrogen vehicles. Releases from compressed gaseous hydrogen (CGH2) and liquid hydrogen (LH2) powered vehicles have been studied under various tunnel geometries and ventilation regimes. The findings drawn from the limited work done so far indicate that under normal circumstances hydrogen powered vehicles do not pose a significantly higher risk than those powered by petrol diesel or CNG but this needs to be confirmed by further research. In particular obstructions at tunnel ceiling level have been identified as a potential hazard in respect to fast deflagration or even detonation in some circumstances which warrants further investigation. The shape of the tunnel tunnel ventilation and vehicle pressure relief device (PRD) operation are potentially important parameters in determining explosion risks and the appropriate mitigation measures.
Hydrogen-powered Vehicles in Urban Transport Systems – Current State and Development
Mar 2020
Publication
The work is dedicated to the possibility of using hydrogen-powered vehicles in urban transport systems. Due to the need to look for alternative solutions for vehicles with conventional drive in cities hydrogen-powered cars are one of the practical possibilities of realizing the sustainable transport assumptions and independence from oil imports - which is one of the main priorities of the European Union. This paper presents a literature analysis the analysis of the current state and development of use hydrogen-powered vehicles in the world.<br/>The article refers to the possibilities of use hydrogen-vehicles in different ways of mobility: individual vehicles taxis and shared mobility. In addition the author focused on showing the advantages and disadvantages of using hydrogen-powered vehicles in urban transport systems.
Using Hydrogen Reactors to Improve the Diesel Engine Performance
Apr 2022
Publication
This work is aimed at solving the problem of converting diesel power drives to diesel– hydrogen fuels which are more environmentally friendly and less expensive alternatives to diesel fuel. The method of increasing the energy efficiency of diesel fuels has been improved. The thermochemical essence of using methanol as an alternative fuel to increase energy efficiency based on the provisions of thermotechnics is considered. Alternative methanol fuel has been chosen as the initial product for the hydrogen conversion process and its energy value cost and temperature conditions have been taken into account. Calculations showed that the caloric effect from the combustion of the converted mixture of hydrogen H2 and carbon monoxide CO exceeds the effect from the combustion of the same amount of methanol fuel. Engine power and fuel energy were increased due to the thermochemical regeneration of engine exhaust gas heat. An experimental setup was created to study the operation of a converted diesel engine on diesel–hydrogen products. Experimental studies of power and environmental parameters of a diesel engine converted for diesel–hydrogen products were performed. The studies showed that the conversion of diesel engines to operate using diesel– hydrogen products is technically feasible. A reduction in energy consumption was accompanied by an improvement in the environmental performance of the diesel–hydrogen engine working together with a chemical methanol conversion thermoreactor. The formation of carbon monoxide occurred in the range of 52–62%; nitrogen oxides in the exhaust gases decreased by 53–60% according to the crankshaft speed and loading on the experimental engine. In addition soot emissions were reduced by 17% for the engine fueled with the diesel–hydrogen fuel. The conversion of diesel engines for diesel–hydrogen products is very profitable because the price of methanol is on average 10–20% of the cost of petroleum fuel.
Enhanced Production of Hydrogen from Methanol Using Spark Discharge Generated in a Small Portable Reactor
Nov 2021
Publication
An efficient production of hydrogen from a mixture of methanol and water is possible in a spark discharge. In this discharge there is a synergistic effect of high-energy electrons and high temperature interactions which enables an efficient course of endothermic processes such as the production of hydrogen from methanol. The water to methanol molar ratio of 1:1 was kept constant during the study. While the discharge power and feed flow rate were varied from 15 to 55 W and from 0.25 to 2 mol/h respectively which corresponded to the residence time of the reactants in the plasma zone from 58 to 7 ms. The cooled gas mixture contained 56 to 60% of H2. Other gaseous products of the process were CO CO2 and a small amount of CH4. The maximum energy yield was 16.2 mol(H2)/kWh which represents 20% of the theoretical energy yield when the substrates are in a liquid phase.
Operation Analysis of Selected Domestic Appliances Supplied with Mixture of Nitrogen-Rich Natural Gas with Hydrogen
Dec 2021
Publication
This is article presents the results of the testing of the addition of a hydrogen-to-nitrogen-rich natural gas of the Lw group and its influence on the operation of selected gas-fired domestic appliances. The tests were performed on appliances used for the preparation of meals and hot water production for hygienic and heating purposes. The characteristics of the tested gas appliances are also presented. The burners and their controllers with which the tested appliances were equipped were adapted for the combustion of Lw natural gas. The tested appliances reflected the most popular designs for domestic gas appliances in their group used both in Poland and in other European countries. The tested appliances were supplied with nitrogen-rich natural gas of the Lw group and a mixture of this gas with hydrogen at 13.2% content. The article presents the approximate percentage compositions of the gases used during the tests and their energy parameters. The research was focused on checking the following operating parameters and the safety of the tested appliances: the rated heat input thermal efficiency combustion quality ignition flame stability and transfer. The article contains an analysis of the test results referring in detail to the issue of decreasing the heat input of the appliances by lowering the energy parameters of the nitrogen-rich natural gas of the Lw group mixture with a hydrogen addition and how it influenced the thermal efficiency achieved by the appliances. The conclusions contain an explanation regarding among other things how the design of an appliance influences the thermal efficiency achieved by it in relation to the heat input decrease. In the conclusions on the basis of the research results answers have been provided to the following questions: (1) Whether the hydrogen addition to the nitrogen-rich natural gas of the Lw group will influence the safe and proper operation of domestic gas appliances; (2) What hydrogen percentage can be added to the nitrogen-rich natural gas of the Lw group in order for the appliances adapted for combusting it to operate safely and effectively without the need for modifying them?
Integration of Experimental Facilities: A Joint Effort for Establishing a Common Knowledge Base in Experimental Work on Hydrogen Safety
Sep 2009
Publication
With regard to the goals of the European HySafe Network research facilities are essential for the experimental investigation of relevant phenomena for testing devices and safety concepts as well as for the generation of validation data for the various numerical codes and models. The integrating activity ‘Integration of Experimental Facilities (IEF)’ has provided basic support for jointly performed experimental work within HySafe. Even beyond the funding period of the NoE HySafe in the 6th Framework Programme IEF represents a long lasting effort for reaching sustainable integration of the experimental research capacities and expertise of the partners from different research fields. In order to achieve a high standard in the quality of experimental data provided by the partners emphasis was put on the know-how transfer between the partners. The strategy for reaching the objectives consisted of two parts. On the one hand a documentation of the experimental capacities has been prepared and analysed. On the other hand a communication base has been established by means of biannual workshops on experimental issues. A total of 8 well received workshops has been organised covering topics from measurement technologies to safety issues. Based on the information presented by the partners a working document on best practice including the joint experimental knowledge of all partners with regard to experiments and instrumentation was created. Preserving the character of a working document it was implemented in the IEF wiki website which was set up in order to provide a central communication platform. The paper gives an overview of the IEF network activities over the last 5 years.
Numerical Analysis of Detonation Propensity of Hydrogen-air Mixtures with Addition of Methane, Ethane or Propane
Oct 2015
Publication
The detonation propensity of hydrogen-air mixtures with addition of methane ethane or propane in wide range of compositions is analyzed. The analysis concerned the detonation cell width ignition delay time RSB and parameters. Results are presented as a function of hydrogen molar fraction. Computations were performed with the use of three Cantera 2.1.1. scripts in the Matlab R2010b environment. The validated mechanisms of chemical reactions based on data available in the literature were used. Six mechanisms were assessed: GRI-Mech 3.0 LLNL SanDiego Wang POLIMI and AramcoMech. In conclusion the relation between detonation propensity parameters is discussed.
On the Use of Hydrogen in Confined Spaces: Results from the Internal Project InsHyde
Sep 2009
Publication
Alexandros G. Venetsanos,
Paul Adams,
Inaki Azkarate,
A. Bengaouer,
Marco Carcassi,
Angunn Engebø,
E. Gallego,
Olav Roald Hansen,
Stuart J. Hawksworth,
Thomas Jordan,
Armin Keßler,
Sanjay Kumar,
Vladimir V. Molkov,
Sandra Nilsen,
Ernst Arndt Reinecke,
M. Stöcklin,
Ulrich Schmidtchen,
Andrzej Teodorczyk,
D. Tigreat,
N. H. A. Versloot and
L. Boon-Brett
The paper presents an overview of the main achievements of the internal project InsHyde of the HySafe NoE. The scope of InsHyde was to investigate realistic small-medium indoor hydrogen leaks and provide recommendations for the safe use/storage of indoor hydrogen systems. Additionally InsHyde served to integrate proposals from HySafe work packages and existing external research projects towards a common effort. Following a state of the art review InsHyde activities expanded into experimental and simulation work. Dispersion experiments were performed using hydrogen and helium at the INERIS gallery facility to evaluate short and long term dispersion patterns in garage like settings. A new facility (GARAGE) was built at CEA and dispersion experiments were performed there using helium to evaluate hydrogen dispersion under highly controlled conditions. In parallel combustion experiments were performed by FZK to evaluate the maximum amount of hydrogen that could be safely ignited indoors. The combustion experiments were extended later on by KI at their test site by considering the ignition of larger amounts of hydrogen in obstructed environments outdoors. An evaluation of the performance of commercial hydrogen detectors as well as inter-lab calibration work was jointly performed by JRC INERIS and BAM. Simulation work was as intensive as the experimental work with participation from most of the partners. It included pre-test simulations validation of the available CFD codes against previously performed experiments with significant CFD code inter-comparisons as well as CFD application to investigate specific realistic scenarios. Additionally an evaluation of permeation issues was performed by VOLVO CEA NCSRD and UU by combining theoretical computational and experimental approaches with the results being presented to key automotive regulations and standards groups. Finally the InsHyde project concluded with a public document providing initial guidance on the use of hydrogen in confined spaces.
From Coal Ashes to Solid Sorbents for Hydrogen Storage
Jun 2020
Publication
The purpose of this work is the literature review in the field of hydrogen storage in solid sorbents. The best solid sorbents for hydrogen storage were selected with the possibility of synthesis them from coal fly ash. In addition the on-board hydrogen storage analysis was carried out. The review method consists of two parts. The first part based on research questions included types of the best sorbents for hydrogen storage the possibility to obtain them from coal fly ash and practical use in hydrogen storage system on-board. The second part was the selection of publications from The Web of Science and Elsevier Scopus databases and the analysis as well as available reports on the websites at this scope. After searching the relevant articles in the databases abstracts were analysed in terms of the questions asked. The links between references and research were checked. The search procedure was repeated several times. Finally articles with high Impact Factor index published by authors recognized on a global scale were selected for the presented review. The collected information proved that carbon materials are suited to hydrogen storage because of their high porosity large specific surface area and thermal stability. Besides solid sorbents such as zeolites metal-organic frameworks activated carbons or zeolite template carbons can be obtained from coal fly ash. Thanks to silicon aluminium and unburned carbon content fly ash is a good material for the synthesis of hydrogen sorbents. Under cryogenic conditions and high pressure it is possible to adsorb as much as 8.5 wt% of hydrogen. Although the Department of Energy (DOE) requirements for the hydrogen storage system on-board vehicles are not met the review of scientific publications shows that research in this area is developing and better parameters are being obtained.
Production of Hydrogen and Methane from Lignocellulose Waste by Fermentation. A Review of Chemical Pretreatment for Enhancing the Efficiency of the Digestion Process
May 2020
Publication
In Poland lignocellulose wastes constitute about 43% of municipal waste (∼4 417 Gg). Anaerobic and/or dark fermentation are sustainable methods of lignocellulosic waste-management and contribute greatly to ever increasing demand for energy and products. This paper presents the results of the theoretical potential of methane and hydrogen yields from lignocellulosic wastes. Also state-of-the-art methods in the field of lignocellulose fermentation as well as its development and pretreatment are discussed. The main reason for applying pretreatment is the decomposition (decrystallization) of cellulose and hemicellulose and cleavage of polymers into monomers which may be more easily digested by bacteria in DF and AD fermentation processes. At current price levels the cheapest methods are basic and acidic pretreatments. Acidic pretreatment is very efficient (especially using sulfuric acids) solubilizing up to 80% of lignocellulose but strong acids produce inhibitors and are highly corrosive. Alkaline pretreatment is a competitive and even more efficient (>80%) method to acidic pretreatment especially for some rigid materials that acid cannot solubilize. Oxidative pretreatment is usually expensive but can support the sacharisation process by either alkaline or acidic methods; in the case of NMMO efficiency reaching 82%. Ion-liquid pretreatment is selective (almost 100% sacharisation) but very costly and is too expensive for hydrogen production. The last methods can be profitable if some valuable by-products results. An efficient chemical pretreatment should be preceded by physical comminution e.g. mechanical which is the cheapest one.
Mechanical Properties of Gas Main Steels after Long-Term Operation and Peculiarities of Their Fracture Surface Morphology
Feb 2019
Publication
Regularities of steel structure degradation of the “Novopskov-Aksay-Mozdok” gas main pipelines (Nevinnomysskaya CS) as well as the “Gorky-Center” pipelines (Gavrilovskaya CS) were studied. The revealed peculiarities of their degradation after long-term operation are suggested to be treated as a particular case of the damage accumulation classification (scheme) proposed by prof. H.M. Nykyforchyn. It is shown that the fracture surface consists of sections of ductile separation and localized zones of micro-spalling. The presence of the latter testifies to the hydrogen-induced embrittlement effect. However the steels under investigation possess sufficiently high levels of the mechanical properties required for their further safe exploitation both in terms of durability and cracking resistance.
Study of the Effects of Changes in Gas Composition as Well as Ambient and Gas Temperature on Errors of Indications of Thermal Gas Meters
Oct 2020
Publication
Thermal gas meters represent a promising technology for billing customers for gaseous fuels however it is essential to ensure that measurement accuracy is maintained in the long term and in a broad range of operating conditions. The effect of hydrogen addition to natural gas will change the physicochemical properties of the mixture of natural gas and hydrogen. Such a mixture will be supplied through the gas system to consumers including households where the amounts of received gas will be metered. The physicochemical properties of hydrogen including the specific density or viscosity differ significantly from those of the natural gas components such as methane ethane propane nitrogen etc. Therefore it is of utmost importance to establish the impact of the changes in the gas composition caused by the addition of hydrogen to natural gas on the metrological properties of household gas meters including thermal gas meters. Furthermore since household gas meters can be installed outdoors and taking into account the fact that household gas meters are good heat exchangers the influence of ambient and gas temperature on the metrological properties of those meters should be investigated. This article reviews a test bench and a testing method concerning errors of thermal gas meter indicators using air and natural gas including the type containing hydrogen. The indication errors for thermal gas meters using air natural gas and natural gas with an addition of 2% 4% 5% 10% and 15% hydrogen were determined and then subjected to metrological analysis. Moreover the test method and test bench are discussed and the results of tests on the impact of ambient and gas temperatures (-25 ◦C and 55 ◦C respectively) on the errors of indications of thermal gas meters are presented. Conclusions for distribution system operators in terms of gas meter selection were drawn based on the test results.
Sustainable Hydrogen Production by Plasmonic Thermophotocatalysis
Feb 2021
Publication
A vision of hydrogen based economy and clean sustainable fossil fuels-free world inspires the scientific community to put much effort into the development of visible-light-driven photochemistry and efficient solar energy harvesting. The unique features of plasmonic nanomaterials such as capability of significant electric field amplification an extreme local heating generation of high energy charge carriers and broad tunability of optical properties coupled to catalytically active surfaces provide an exciting opportunity for hydrogen production with solar photochemistry. This review sums up recent progress in the development of plasmonic thermophotocatalysis paying particular attention to sustainable production of hydrogen. We approach the subject from a broad bottom-up perspective beginning with the brief description of plasmon-related phenomena and plasmon-assisted photochemistry through the demonstration of various plasmonic nanostructures their synthesis and hydrogen production efficiency ending with the idea of continuous-flow reactors and their future implementation in hydrogen production by plasmonic thermophotocatalysis. Finally we summarize the review and highlight the remaining challenges that have to be faced before the widespread commercialization of this technology.
Hydrogen Production During Direct Cellulose Fermentation by Mixed Bacterial Culture: The Relationship Between the Key Process Parameters Using Response Surface Methodology
Jun 2021
Publication
Dark fermentation is a promising method to produce hydrogen from lignocellulosic biomass. This study assessed the influence of temperature phosphate buffer concentration and substrate concentration on direct hydrogen production form cellulose using response surface methodology. Mixed bacterial culture was successfully enriched on cellulose and used as an inoculum for hydrogen production. The model indicated that the highest cumulative hydrogen production (CHP) of 2.14 L H2/Lmedium could be obtained at 13.5 gcellulose/L 79.5 mM buffer and 32.6 °C. However hydrogen yield is then only 0.58 mol H2/molhexose due to low substrate conversion efficiency (SCE). Simultaneous optimization of CHP and SCE with desirability function approach resulted in the H2 yield of 2.71 ± 0.1 mol H2/molhexose and 93.8 ± 1.8% SCE at 3.35 gcellulose/L 69 mM buffer and 32.9 °C. Phosphate concentration above 80 mM decreased H2 production but had positive effect on cellulose consumption. The bacterial community analysis showed that Ruminiclostridium papyrosolvens was responsible for cellulose hydrolysis. Lachnoclostridium sp. was positively correlated with ethanol production at high phosphate buffer concentration while Caproiciproducens sp. with caproate production at low buffer concentration. The obtained results opens the possibility of simultaneous hydrogen and caproate production from cellulosic substrates.
Aging Effects on Modelling and Operation of a Photovoltaic System with Hydrogen Storage
Jun 2021
Publication
In this work the aging effects on modelling and operation of a photovoltaic system with hydrogen storage in terms of energy production decrease and demand for additional hydrogen during 10 years of the system operation was analysed for the entire energy system for the first time. The analyses were performed with the support of experimental data for the renewable energy system composed of photovoltaic modules fuel cell electrolysers hydrogen storage and hydrogen backup.<br/>It has been found that the total degradation of the analysed system can be described by the proposed parameter – unit additional hydrogen consumption ratio. The results reveal a 33.2–36.2% increase of the unit fuel requirement from an external source after 10 years in reference to the initial condition. Degradation of the components can on the other hand be well described with the unit hydrogen consumption ratio by fuel cell for electricity or the unit electricity consumption ratio by electrolyser for hydrogen production which has been found to vary for the electrolyser in the range of 4.6–4.9% and for the fuel cell stack in the range of 13.4–15.1% during the 10 years of the system operation. The analyses indicate that this value depends on the load profile and PV module types and the system performance decline is non-linear."
Research on the Concept of Hydrogen Supply Chains and Power Grids Powered by Renewable Energy Sources: A Scoping Review with the Use of Text Mining
Jan 2022
Publication
The key direction of political actions in the field of sustainable development of the energy sector and economy is the process of energy transformation (decarbonization) and increasing the share of renewable energy sources (RES) in the supply of primary energy. Regardless of the indisputable advantages RES are referred to as unstable energy sources. A possible solution might be the development of the concept of hydrogen supply chains especially the so-called green hydrogen obtained in the process of electrolysis from electricity produced from RES. The aim of the research undertaken in the article is to identify the scope of research carried out in the area of hydrogen supply chains and to link this research with the issues of the operation of electricity distribution networks powered by RES. As a result of the scoping review and the application of the text-mining method using the IRaMuTeQ tool which includes the analysis of the content of 12 review articles presenting the current research achievements in this field over the last three years (2016–2020) it was established that the issues related to hydrogen supply chains including green hydrogen are still not significantly associated with the problem of the operation of power grids. The results of the conducted research allow formulating recommendations for further research areas.
Models of Delivery of Sustainable Public Transportation Services in Metropolitan Areas–Comparison of Conventional, Battery Powered and Hydrogen Fuel-Cell Drives
Nov 2021
Publication
The development of public transport systems is related to the implementation of modern and low-carbon vehicles. Over the last several years there has been a clear progress in this field. The number of electric buses has increased and the first solutions in the area of hydrogen fuel cells have been implemented. Unfortunately the implementation of these technologies is connected with significant financial expenditure. The goal of the article is the analysis of effectiveness of financial investment consisting in the purchase of 30 new public transport buses (together with the necessary infrastructure–charging stations). The analysis has been performed using the NPV method for the period of 10 years. Discount rate was determined on 4% as recommended by the European Commission for this type of project. It is based on the case study of the investment project carried out by Metropolis GZM in Poland. The article determines and compares the efficiency ratios for three investment options-purchase of diesel-powered battery-powered and hydrogen fuel-cell electric vehicles. The results of the analysis indicate that the currently high costs of vehicle purchase and charging infrastructure are a significant barrier for the implementation of battery-powered and hydrogen fuel-cell buses. In order to meet the transport policy goals related to the exchange of traditional bus stock to more eco-friendly vehicles it is necessary to involve public funds for the purpose of financing the investment activities.
Problems of Hydrogen Doping in the Methane Fermentation Process and of Energetic Use of the Gas Mixture
Jul 2021
Publication
This article discusses the technology for doping hydrogen into the fermenter to increase methane production and the amount of energy in the mixture. Hydrogen doping is anticipated to enable more carbon to be applied to produce methane. Hydrogen is proposed to be produced by using excess electricity from for example off-peak electricity hours at night. The possibilities of using a mixture of hydrogen and biogas for combustion in boilers and internal combustion engines have been determined. It has been proven that the volumetric addition of hydrogen reduces the heat of combustion of the mixture. Problems arising from hydrogen doping during the methane fermentation process have been identified.
Requirements for Hydrogen Resistance of Materials in CI Engine Toxic Substances Powered by Biofuels
Aug 2019
Publication
It has been described the conception of using platinum catalytic layer in multi hole fuel injector atomizer. The catalytic layer has been placed on not working part of atomizer needle. The aim of modification was activation of dehydrogenation reaction paraffin to olefin hydrocarbons with escape hydrogen molecule in CI engine bio fuel. The modification of atomizer with catalytic layer and reaction process leads to the presence of hydrogen and its influence on structural materials properties after the catalysis which requires the high hydrogen and crack resistance of used materials. There is used high speed steel as material. Article describes how hydrogen and combustion gases influence on thermal friction processes on this material. First of all the investigations were conduct 359 engine with biodiesel. During test had been observed nitrogen oxides carbon monoxide and particles emission. The obtained results show that there is possibility to lower toxic substances emission in exhaust gases CI engine powered by biodiesel. On the second it has been described the influence of biodiesel (including hydrogen) on fuel injector components and their influence on structural materials characteristics. There has been presented how biodiesel with hydrogen influences on precision elements and injection and return discharges. The investigation has been made by using engine test bench and fuel injector and pumps test equipment.
Study of the Effect of Addition of Hydrogen to Natural Gas on Diaphragm Gas Meters
Jun 2020
Publication
Power-to-gas technology plays a key role in the success of the energy transformation. This paper addresses issues related to the legal and technical regulations specifying the rules for adding hydrogen to the natural gas network. The main issue reviewed is the effects of the addition of hydrogen to natural gas on the durability of diaphragm gas meters. The possibility of adding hydrogen to the gas network requires confirmation of whether within the expected hydrogen concentrations long-term operation of gas meters will be ensured without compromising their metrological properties and operational safety. Methods for testing the durability of gas meters applied at test benches and sample results of durability tests of gas meters are presented. Based on these results a metrological and statistical analysis was carried out to establish whether the addition of hydrogen affects the durability of gas meters over time. The most important conclusion resulting from the conducted study indicates that for the tested gas meter specimens there was no significant metrological difference between the obtained changes of errors of indications after testing the durability of gas meters with varying hydrogen content (from 0% to 15%).
Thermodynamic, Economic and Environmental Assessment of Renewable Natural Gas Production Systems
May 2020
Publication
One of the options to reduce the dependence on fossil fuels is to produce gas with the quality of natural gas but based on renewable energy sources. It can encompass among other biogas generation from various types of biomass and its subsequent upgrading. The main aim of this study is to analyze under a combined technical economic and environmental perspective three of the most representative technologies for the production of biomethane (bio-based natural gas): (i) manure fermentation and its subsequent upgrading by CO2 removal (ii) manure fermentation and biogas methanation using renewable hydrogen from electrolysis and (iii) biomass gasification in the atmosphere of oxygen and methanation of the resulted gas. Thermodynamic economic and environmental analyses are conducted to thoroughly compare the three cases. For these purposes detailed models in Aspen Plus software were built while environmental analysis was performed using the Life Cycle Assessment methodology. The results show that the highest efficiency (66.80%) and the lowest break-even price of biomethane (19.2 €/GJ) are reached for the technology involving fermentation and CO2 capture. Concerning environmental assessment the system with the best environmental performance varies depending on the impact category analyzed being the system with biomass gasification and methanation a suitable trade-off solution for biomethane production.
Influence of Carbon Catalysts on the Improvement of Hydrogen Storage Properties in a Body-Centered Cubic Solid Solution Alloy
Jun 2021
Publication
Body-centered cubic (BCC) alloys are considered as promising materials for hydrogen storage with high theoretical storage capacity (H/M ratio of 2). Nonetheless they often suffer from sluggish kinetics of hydrogen absorption and high hydrogen desorption temperature. Carbon materials are efficient hydrogenation catalysts however their influence on the hydrogen storage properties of BCC alloy has not been comprehensively studied. Therefore in this paper composites obtained by milling of carbon catalysts (carbon nanotubes mesoporous carbon carbon nanofibers diamond powder graphite fullerene) and BCC alloy (Ti1.5V0.5) were extensively studied in the non-hydrogenated and hydrogenated state. The structure and microstructure of the obtained materials were studied by scanning and transmission electron microscopes X-ray diffraction (XRD) and Raman spectroscopy. XRD and Raman measurements showed that BCC alloy and carbon structures were in most cases intact after the composite synthesis. The hydrogenation/dehydrogenation studies showed that all of the used carbon catalysts significantly improve the hydrogenation kinetics reduce the activation energy of the dehydrogenation process and decrease the dehydrogenation temperature (by nearly 100 K). The superior kinetic properties were measured for the composite with 5 wt % of fullerene that absorbs 3.3 wt % of hydrogen within 1 min at room temperature.
Study of the Microstructural and First Hydrogenation Properties of TiFe Alloy with Zr, Mn and V as Additives
Jul 2021
Publication
In this paper we report the effect of adding Zr + V or Zr + V + Mn to TiFe alloy on microstructure and hydrogen storage properties. The addition of only V was not enough to produce a minimum amount of secondary phase and therefore the first hydrogenation at room temperature under a hydrogen pressure of 20 bars was impossible. When 2 wt.% Zr + 2 wt.% V or 2 wt.% Zr + 2 wt.% V + 2 wt.% Mn is added to TiFe the alloy shows a finely distributed Ti2Fe-like secondary phase. These alloys presented a fast first hydrogenation and a high capacity. The rate-limiting step was found to be 3D growth diffusion controlled with decreasing interface velocity. This is consistent with the hypothesis that the fast reaction is likely to be the presence of Ti2Fe-like secondary phases that act as a gateway for hydrogen.
Assessment of Operational Performance for an Integrated ‘Power to Synthetic Natural Gas’ System
Dec 2021
Publication
This article presents a power to SNG (synthetic natural gas) system that converts hydrogen into SNG via a methanation process. In our analysis detailed models for all the elements of the system are built. We assume a direct connection between a wind farm and a hydrogen generator. For the purposes of our calculations we also assume that the hydrogen generator is powered by the renewable source over a nine-hour period per day (between 21:00 and 06:00) and this corresponds to the off-peak period in energy demand. In addition a hydrogen tank was introduced to maximize the operating time of the methanation reactor. The cooperation between the main components of the system were simulated using Matlab software. The primary aim of this paper is to assess the influence of various parameters on the operation of the proposed system and to optimize its yearly operation via a consideration of the most important constraints. The analyses also examine different nominal power values of renewables from 8 to 12 MW and hydrogen generators from 3 to 6 MW. Implementing the proposed configuration taking into account the direct connection of the hydrogen generator and the methanation reactor showed that it had a positive effect on the dynamics and the operating times of the individual subsystems within the tested configuration
Experimental Determination of Critical Conditions for Hydrogen-air Detonation Propagation in Partially Confined Geometry
Oct 2015
Publication
An experimental investigation was performed to determine critical semi-open channel height (h*) and two-sided open channel width (w*) in which hydrogen-air detonation may propagate. Three types of gaseous mixture composition were used: 25% 29.6% and 40% of hydrogen in air. Experimental setup was based on rectangular (0.11 × 0.11 × 2 m) test channel equipped with acceleration section (0.11 × 0.11 × 1 m). Different channel heights h in range of 15–40 mm and widths w in range of 30–50 mm were used in the test channel. The critical height h* and width w* were defined for each investigated configuration. To determine representative detonation cell sizes λ and to calculate their relationship to h* and w* the sooted plate technique was used. The results showed that detonation in stoichiometric H2-air mixture may propagate in semi-open channel only when the channel height is very close to or higher than approximately 3λ. For less reactive mixtures critical relation h*/λ reaches 3.1 or 3.6 for mixtures with 25% and 40% of hydrogen in air respectively. For two-sided open channel similar relations w*/λ were close to 4.9 and 5.5 for 29.6%H2 and 40%H2 in air respectively.
No more items...