United States
Advanced Hydrogen and CO2 Capture Technology for Sour Syngas
Apr 2011
Publication
A key challenge for future clean power or hydrogen projects via gasification is the need to reduce the overall cost while achieving significant levels of CO2 capture. The current state of the art technology for capturing CO2 from sour syngas uses a physical solvent absorption process (acid gas removal–AGR) such as Selexol™ or Rectisol® to selectively separate H2S and CO2 from the H2. These two processes are expensive and require significant utility consumption during operation which only escalates with increasing levels of CO2 capture. Importantly Air Products has developed an alternative option that can achieve a higher level of CO2 capture than the conventional technologies at significantly lower capital and operating costs. Overall the system is expected to reduce the cost of CO2 capture by over 25%.<br/>Air Products developed this novel technology by leveraging years of experience in the design and operation of H2 pressure swing adsorption (PSA) systems in its numerous steam methane reformers. Commercial PSAs typically operate on clean syngas and thus need an upstream AGR unit to operate in a gasification process. Air Products recognized that a H2 PSA technology adapted to handle sour feedgas (Sour PSA) would enable a new and enhanced improvement to a gasification system. The complete Air Products CO2 Capture technology (CCT) for sour syngas consists of a Sour PSA unit followed by a low-BTU sour oxycombustion unit and finally a CO2 purification / compression system.
Large Transition State Stabilization From a Weak Hydrogen Bond
Jul 2020
Publication
A series of molecular rotors was designed to study and measure the rate accelerating effects of an intramolecular hydrogen bond. The rotors form a weak neutral O–H⋯O[double bond length as m-dash]C hydrogen bond in the planar transition state (TS) of the bond rotation process. The rotational barrier of the hydrogen bonding rotors was dramatically lower (9.9 kcal mol−1) than control rotors which could not form hydrogen bonds. The magnitude of the stabilization was significantly larger than predicted based on the independently measured strength of a similar O–H⋯O[double bond length as m-dash]C hydrogen bond (1.5 kcal mol−1). The origins of the large transition state stabilization were studied via experimental substituent effect and computational perturbation analyses. Energy decomposition analysis of the hydrogen bonding interaction revealed a significant reduction in the repulsive component of the hydrogen bonding interaction. The rigid framework of the molecular rotors positions and preorganizes the interacting groups in the transition state. This study demonstrates that with proper design a single hydrogen bond can lead to a TS stabilization that is greater than the intrinsic interaction energy which has applications in catalyst design and in the study of enzyme mechanisms.
Hydrogen Systems Component Safety
Sep 2013
Publication
The deployment of hydrogen technologies particularly the deployment of hydrogen dispensing systems for passenger vehicles requires that hydrogen components perform reliably in environments where they have to meet the following performance parameters:
The paper will use incident frequency data from NREL’s Technology Validation project to more quantitatively identify safety concerns in hydrogen dispensing and storage systems.
- Perform safely where the consumer will be operating the dispensing equipment
- Dispense hydrogen at volumes comparable to gasoline dispensing stations in timeframes comparable to gasoline stations
- Deliver a fueling performance that is within the boundaries of consumer tolerance
- Perform with maintenance/incident frequencies comparable to gasoline dispensing systems
The paper will use incident frequency data from NREL’s Technology Validation project to more quantitatively identify safety concerns in hydrogen dispensing and storage systems.
Decarbonization Synergies From Joint Planning of Electricity and Hydrogen Production: A Texas Case Study
Oct 2020
Publication
Hydrogen (H2) shows promise as an energy carrier in contributing to emissions reductions from sectors which have been difficult to decarbonize like industry and transportation. At the same time flexible H2 production via electrolysis can also support cost-effective integration of high shares of variable renewable energy (VRE) in the power system. In this work we develop a least-cost investment planning model to co-optimize investments in electricity and H2 infrastructure to serve electricity and H2 demands under various low-carbon scenarios. Applying the model to a case study of Texas in 2050 we find that H2 is produced in approximately equal amounts from electricity and natural gas under the least-cost expansion plan with a CO2 price of $30–60/tonne. An increasing CO2 price favors electrolysis while increasing H2 demand favors H2 production from Steam Methane Reforming (SMR) of natural gas. H2 production is found to be a cost effective solution to reduce emissions in the electric power system as it provides flexibility otherwise provided by natural gas power plants and enables high shares of VRE with less battery storage. Additionally the availability of flexible electricity demand via electrolysis makes carbon capture and storage (CCS) deployment for SMR cost-effective at lower CO2 prices ($90/tonne CO2) than for power generation ($180/tonne CO2 ). The total emissions attributable to H2 production is found to be dependent on the H2 demand. The marginal emissions from H2 production increase with the H2 demand for CO2 prices less than $90/tonne CO2 due to shift in supply from electrolysis to SMR. For a CO2 price of $60/tonne we estimate the production weighted-average H2 price to be between $1.30–1.66/kg across three H2 demand scenarios. These findings indicate the importance of joint planning of electricity and H2 infrastructure for cost-effective energy system decarbonization.
Characteristic of Cryogenic Hydrogen Flames from High-aspect Ratio Nozzles
Sep 2019
Publication
Unintentional leaks at hydrogen fuelling stations have the potential to form hydrogen jet flames which pose a risk to people and infrastructure. The heat flux from these jet flames are often used to develop separation distances between hydrogen components and buildings lot-lines etc. The heat flux and visible flame length is well understood for releases from round nozzles but real unintended releases would be expected to be be higher aspect-ratio cracks. In this work we measured the visible flame length and heat-flux characteristics of cryogenic hydrogen flames from high-aspect ratio nozzles. We compare this data to flames of both cryogenic and compressed hydrogen from round nozzles. The aspect ratio of the release does not affect the flame length or heat flux significantly for a given mass flow under the range of conditions studied. The engineering correlations presented in this work that enable the prediction of flame length and heat flux can be used to assess risk at hydrogen fuelling stations with liquid hydrogen and develop science-based separation distances for these stations.
ISO 19880-1, Hydrogen Fueling Station and Vehicle Interface Safety Technical Report
Oct 2015
Publication
Hydrogen Infrastructures are currently being built up to support the initial commercialization of the fuel cell vehicle by multiple automakers. Three primary markets are presently coordinating a large build up of hydrogen stations: Japan; USA; and Europe to support this. Hydrogen Fuelling Station General Safety and Performance Considerations are important to establish before a wide scale infrastructure is established.
This document introduces the ISO Technical Report 19880-1 and summarizes main elements of the proposed standard. Note: this ICHS paper is based on the draft TR 19880 and is subject to change when the document is published in 2015. International Standards Organisation (ISO) Technical Committee (TC) 197 Working Group (WG) 24 has been tasked with the preparation of the ISO standard 19880-1 to define the minimum requirements considered applicable worldwide for the hydrogen and electrical safety of hydrogen stations. This report includes safety considerations for hydrogen station equipment and components control systems and operation. The following systems are covered specifically in the document as shown in Figure 1:
This document introduces the ISO Technical Report 19880-1 and summarizes main elements of the proposed standard. Note: this ICHS paper is based on the draft TR 19880 and is subject to change when the document is published in 2015. International Standards Organisation (ISO) Technical Committee (TC) 197 Working Group (WG) 24 has been tasked with the preparation of the ISO standard 19880-1 to define the minimum requirements considered applicable worldwide for the hydrogen and electrical safety of hydrogen stations. This report includes safety considerations for hydrogen station equipment and components control systems and operation. The following systems are covered specifically in the document as shown in Figure 1:
- H2 production / supply delivery system
- Compression
- Gaseous hydrogen buffer storage;
- Pre-cooling device;
- Gaseous hydrogen dispensers.
- Hydrogen Fuelling Vehicle Interface
Stress–Corrosion Cracking of AISI 316L Stainless Steel in Seawater Environments: Effect of Surface Machining
Oct 2020
Publication
To understand the effect of surface machining on the resistance of AISI 316L to SCC (stress–corrosion cracking) in marine environments we tested nuts surface-machined by different methods in a seawater-spraying chamber. Two forms of cracks were observed: on the machined surface and underneath it. On the surface cracks connected with the pitting sites were observed to propagate perpendicular to the hoop-stress direction identifying them as stress–corrosion cracks. Under the surface catastrophic transgranular cracks developed likely driven by hydrogen embrittlement caused by the chloride-concentrating level of humidity in the testing environment. Under constant testing conditions significantly different SCC resistance was observed depending on how the nuts had been machined. Statistical evaluation of the nut surface-crack density indicates that machining by a “form” tool yields a crack density one order of magnitude lower than machining by a “single-point” tool. Microstructural analysis of form-tool-machined nuts revealed a homogeneous deformed subsurface zone with nanosized grains leading to enhanced surface hardness. Apparently the reduced grain size and/or the associated mechanical hardening improve resistance to SCC. The nanograin subsurface zone was not observed on nuts machined by a single-point tool. Surface roughness measurements indicate that single-point-tool-machined nuts have a rougher surface than form-tool machined nuts. Apparently surface roughness reduces SCC resistance by increasing the susceptibility to etch attack in Cl--rich solutions. The results of X-ray diffractometry and transmission electron microscopy diffractometry indicate that machining with either tool generates a small volume fraction (< 0.01) of strain-induced martensite. However considering the small volume fraction and absence of martensite in regions of cracking martensite is not primarily responsible for SCC in marine environments.
Highly Porous Organic Polymers for Hydrogen Fuel Storage
Apr 2019
Publication
Hydrogen (H2) is one of the best candidates to replace current petroleum energy resources due to its rich abundance and clean combustion. However the storage of H2presents a major challenge. There are two methods for storing H2 fuel chemical and physical both of which have some advantages and disadvantages. In physical storage highly porous organic polymers are of particular interest since they are low cost easy to scale up metal-free and environmentally friendly.
In this review highly porous polymers for H2 fuel storage are examined from five perspectives:
(a) brief comparison of H2 storage in highly porous polymers and other storage media;
(b) theoretical considerations of the physical storage of H2 molecules in porous polymers;
(c) H2 storage in different classes of highly porous organic polymers;
(d) characterization of microporosity in these polymers; and
(e) future developments for highly porous organic polymers for H2 fuel storage. These topics will provide an introductory overview of highly porous organic polymers in H2 fuel storage.
In this review highly porous polymers for H2 fuel storage are examined from five perspectives:
(a) brief comparison of H2 storage in highly porous polymers and other storage media;
(b) theoretical considerations of the physical storage of H2 molecules in porous polymers;
(c) H2 storage in different classes of highly porous organic polymers;
(d) characterization of microporosity in these polymers; and
(e) future developments for highly porous organic polymers for H2 fuel storage. These topics will provide an introductory overview of highly porous organic polymers in H2 fuel storage.
Test Methodologies for Hydrogen Sensor Performance Assessment: Chamber vs. Flow-through Test Apparatus
Sep 2017
Publication
Certification of hydrogen sensors to meet standards often prescribes using large-volume test chambers. However feedback from stakeholders such as sensor manufacturers and end-users indicates that chamber test methods are often viewed as too slow and expensive for routine assessment. Flow-through test methods are potentially an efficient and cost-effective alternative for sensor performance assessment. A large number of sensors can be simultaneously tested in series or in parallel with an appropriate flow-through test fixture. The recent development of sensors with response times of less than 1s mandates improvements in equipment and methodology to properly capture the performance of this new generation of fast sensors; flow methods are a viable approach for accurate response and recovery time determinations but there are potential drawbacks. According to ISO 26142 flow-through test methods may not properly simulate ambient applications. In chamber test methods gas transport to the sensor is dominated by diffusion which is viewed by some users as mimicking deployment in rooms and other confined spaces. Conversely in flow-through methods forced flow transports the gas to the sensing element. The advective flow dynamics may induce changes in the sensor behaviour relative to the quasi-quiescent condition that may prevail in chamber test methods. The aim of the current activity in the JRC and NREL sensor laboratories is to develop a validated flow-through apparatus and methods for hydrogen sensor performance testing. In addition to minimizing the impact on sensor behaviour induced by differences in flow dynamics challenges associated with flow-through methods include the ability to control environmental parameters (humidity pressure and temperature) during the test and changes in the test gas composition induced by chemical reactions with upstream sensors. Guidelines on flow-through test apparatus design and protocols for the evaluation of hydrogen sensor performance have been developed. Various commercial sensor platforms (e.g. thermal conductivity catalytic and metal semiconductor) were used to demonstrate the advantages and issues with the flow-through methodology.
Acid Acceleration of Hydrogen Generation Using Seawater as a Reactant
Jul 2016
Publication
The present study describes hydrogen generation from NaBH4 in the presence of acid accelerator boric oxide or B2O3 using seawater as a reactant. Reaction times and temperatures are adjusted using various delivery methods: bulk addition funnel and metering pump. It is found that the transition metal catalysts typically used to generate hydrogen gas are poisoned by seawater. B2O3 is not poisoned by seawater; in fact reaction times are considerably faster in seawater using B2O3. Reaction times and temperatures are compared for pure water and seawater for each delivery method. It is found that using B2O3 with pure water bulk addition is 97% complete in 3 min; pump metering provides a convenient method to extend the time to 27 min a factor of 9 increase above bulk addition. Using B2O3 with seawater as a reactant bulk addition is 97% complete in 1.35 min; pump metering extends the time to 23 min a factor of 17 increase above bulk. A second acid accelerator sodium bisulfate or NaHSO4 is investigated here for use with NaBH4 in seawater. Because it is non-reactive in seawater i.e. no spontaneous H2 generation NaHSO4 can be stored as a solution in seawater; because of its large solubility it is ready to be metered into NaBH4. With NaHSO4 in seawater pump metering increases the time to 97% completion from 3.4 min to 21 min. Metering allows the instantaneous flow rate of H2 and reaction times and temperatures to be tailored to a particular application. In one application the seawater hydrogen generator characterized here is ideal for supplying H2 gas directly to Proton Exchange Membrane fuel cells in sea surface or subsea environments where a reliable source of power is needed.
Comparison of Two-layer Model for High Pressure Hydrogen Jets with Notional Nozzle Model Predictions and Experimental Data
Oct 2015
Publication
A two-layer reduced order model of high pressure hydrogen jets was developed which includes partitioning of the flow between the central core jet region leading to the Mach disk and the supersonic slip region around the core. The flow after the Mach disk is subsonic while the flow around the Mach disk is supersonic with a significant amount of entrained air. This flow structure significantly affects the hydrogen concentration profiles downstream. The predictions of this model are compared to previous experimental data for high pressure hydrogen jets up to 20 MPa and to notional nozzle models and CFD models for pressures up to 35 MPa using ideal gas properties. The results show that this reduced order model gives better predictions of the mole fraction distributions than previous models for highly underexpanded jets. The predicted locations of the 4% lower flammability limit also show that the two-layer model much more accurately predicts the measured locations than the notional nozzle models. The comparisons also show that the CFD model always underpredicts the measured mole fraction concentrations.
Self-sustainable Protonic Ceramic Electrochemical cells Using a Triple Conducting Electrode for Hydrogen and Power Production
Apr 2020
Publication
The protonic ceramic electrochemical cell (PCEC) is an emerging and attractive technology that converts energy between power and hydrogen using solid oxide proton conductors at intermediate temperatures. To achieve efficient electrochemical hydrogen and power production with stable operation highly robust and durable electrodes are urgently desired to facilitate water oxidation and oxygen reduction reactions which are the critical steps for both electrolysis and fuel cell operation especially at reduced temperatures. In this study a triple conducting oxide of PrNi0.5Co0.5O3-δ perovskite is developed as an oxygen electrode presenting superior electrochemical performance at 400~600 °C. More importantly the self-sustainable and reversible operation is successfully demonstrated by converting the generated hydrogen in electrolysis mode to electricity without any hydrogen addition. The excellent electrocatalytic activity is attributed to the considerable proton conduction as confirmed by hydrogen permeation experiment remarkable hydration behavior and computations.
Numerical Prediction of Cryogenic Hydrogen Vertical Jets
Sep 2019
Publication
Comparison of Computational Fluid Dynamics (CFD) predictions with measurements is presented for cryo-compressed hydrogen vertical jets. The stagnation conditions of the experiments are characteristic of unintended leaks from pipe systems that connect cryogenic hydrogen storage tanks and could be encountered at a fuel cell refuelling station. Jets with pressure up to 5 bar and temperatures just above the saturation liquid temperature were examined. Comparisons are made to the centerline mass fraction and temperature decay rates the radial profiles of mass fraction and the contours of volume fraction. Two notional nozzle approaches are tested to model the under-expanded jet that was formed in the tests with pressures above 2 bar. In both approaches the mass and momentum balance from the throat to the notional nozzle are solved while the temperature at the notional nozzle was assumed equal to the nozzle temperature in the first approach and was calculated by an energy balance in the second approach. The two approaches gave identical results. Satisfactory agreement with the measurements was found in terms of centerline mass fraction and temperature. However for test with 3 and 4 bar release the concentration was overpredicted. Furthermore a wider radial spread was observed in the predictions possibly revealing higher degree of diffusion using the k-ε turbulence model. An integral model for cryogenic jets was also developed and provided good results. Finally a test simulation was performed with an ambient temperature jet and compared to the cold jet showing that warm jets decay faster than cold jets.
An Investigation of Mobile Hydrogen and Fuel Cell Technology Applications
Sep 2019
Publication
Safe practices in the production storage distribution and use of hydrogen are essential for the widespread acceptance of hydrogen and fuel cell technologies. A significant safety incident in any project could damage public perception of hydrogen and fuel cells. A recent incident involving a hydrogen mobile storage trailer in the United States has brought attention to the potential impacts of mobile hydrogen storage and transport. Road transport of bulk hydrogen presents unique hazards that can be very different from those for stationary equipment and new equipment developers may have less experience and expertise than seasoned gas providers. In response to the aforementioned incident and in support of hydrogen and fuel cell activities in California the Hydrogen Safety Panel (HSP) has investigated the safety of mobile hydrogen and fuel cell applications (mobile auxiliary/emergency fuel cell power units mobile fuellers multi-cylinder trailer transport unmanned aircraft power supplies and mobile hydrogen generators). The HSP examined the applications requirements and performance of mobile applications that are being used extensively outside of California to understand how safety considerations are applied. This paper discusses the results of the HSP’s evaluation of hydrogen and fuel cell mobile applications along with recommendations to address relevant safety issues.
Validation of Two-Layer Model for Underexpanded Hydrogen Jets
Sep 2019
Publication
Previous studies have shown that the two-layer model more accurately predicts hydrogen dispersion than the conventional notional nozzle models without significantly increasing the computational expense. However the model was only validated for predicting the concentration distribution and has not been adequately validated for predicting the velocity distributions. In the present study particle imaging velocimetry (PIV) was used to measure the velocity field of an underexpanded hydrogen jet released at 10 bar from a 1.5 mm diameter orifice. The two-layer model was the used to calculate the inlet conditions for a two-dimensional axisymmetric CFD model to simulate the hydrogen jet downstream of the Mach disk. The predicted velocity spreading and centerline decay rates agreed well with the PIV measurements. The predicted concentration distribution was consistent with data from previous planar Rayleigh scattering measurements used to verify the concentration distribution predictions in an earlier study. The jet spreading was also simulated using several widely used notional nozzle models combined with the integral plume model for comparison. These results show that the velocity and concentration distributions are both better predicted by the two-layer model than the notional nozzle models to complement previous studies verifying only the predicted concentration profiles. Thus this study shows that the two-layer model can accurately predict the jet velocity distributions as well as the concentration distributions as verified earlier. Though more validation studies are needed to improve confidence in the model and increase the range of validity the present work indicates that the two-layer model is a promising tool for fast accurate predictions of the flow fields of underexpanded hydrogen jets.
Significantly Enhanced Electrocatalytic Activity of Copper for Hydrogen Evolution Reaction Through Femtosecond Laser Blackening
Jan 2021
Publication
In this work we report on the creation of a black copper via femtosecond laser processing and its application as a novel electrode material. We show that the black copper exhibits an excellent electrocatalytic activity for hydrogen evolution reaction (HER) in alkaline solution. The laser processing results in a unique microstructure: microparticles covered by finer nanoparticles on top. Electrochemical measurements demonstrate that the kinetics of the HER is significantly accelerated after bare copper is treated and turned black. At −0.325 V (v.s. RHE) in 1 M KOH aqueous solution the calculated area-specific charge transfer resistance of the electrode decreases sharply from 159 Ω cm2 for the untreated copper to 1 Ω cm2 for the black copper. The electrochemical surface area of the black copper is measured to be only 2.4 times that of the untreated copper and therefore the significantly enhanced electrocatalytic activity of the black copper for HER is mostly a result of its unique microstructure that favors the formation and enrichment of protons on the surface of copper. This work provides a new strategy for developing high-efficient electrodes for hydrogen generation.
Compliance Measurements of Fuel Cell Electric Vehicle Exhaust
Sep 2019
Publication
The NREL Sensor Laboratory has been developing an analyzer that can verify compliance to the international United Nations Global Technical Regulation number 13 (GTR 13--Global Technical Regulation on Hydrogen and Fuel Cell Vehicles) prescriptive requirements pertaining to allowable hydrogen levels in the exhaust of fuel cell electric vehicles (FCEV) [1]. GTR 13 prescribes that the FCEV exhaust shall remain below 4 vol% H2 over a 3-second moving average and shall not at any time exceed 8 vol% H2 as verified with an analyzer with a response time (t90) of 300 ms or faster. GTR 13 has been implemented and is to serve as the basis for national regulations pertaining to hydrogen powered vehicle safety in the United States Canada Japan and the European Union. In the U.S. vehicle safety is overseen by the Department of Transportation (DOT) through the Federal Motor Vehicle Safety Standards (FMVSS) and in Canada by Transport Canada through the Canadian Motor Vehicle Safety Standard (CMVSS). The NREL FCEV exhaust analyzer is based upon a low-cost commercial hydrogen sensor with a response time (t90) of less than 250 ms. A prototype analyzer and gas probe assembly have been constructed and tested that can interface to the gas sampling system used by Environment and Climate Change Canada’s (ECCC) Emission Research and Measurement Section (ERMS) for the exhaust gas analysis. Through a partnership with Transport Canada ECCC will analyze the hydrogen level in the exhaust of a commercial FCEV. ECCC will use the NREL FCEV Exhaust Gas analyzer to perform these measurements. The analyzer was demonstrated on a FCEV operating under simulated road conditions using a chassis dynamometer at a private facility.
Department of Energy Hydrogen Program Plan
Nov 2020
Publication
The Department of Energy (DOE) Hydrogen Program Plan (the Program Plan or Plan) outlines the strategic high-level focus areas of DOE’s Hydrogen Program (the Program). The term Hydrogen Program refers not to any single office within DOE but rather to the cohesive and coordinated effort of multiple offices that conduct research development and demonstration (RD&D) activities on hydrogen technologies. This terminology and the coordinated efforts on hydrogen among relevant DOE offices have been in place since 2004 and provide an inclusive and strategic view of how the Department coordinates activities on hydrogen across applications and sectors. This version of the Plan updates and expands upon previous versions including the Hydrogen Posture Plan and the DOE Hydrogen and Fuel Cells Program Plan and provides a coordinated high-level summary of hydrogen related activities across DOE.
The 2006 Hydrogen Posture Plan fulfilled the requirement in the Energy Policy Act of 2005 (EPACT 2005) that the Energy Secretary transmit to Congress a coordinated plan for DOE’s hydrogen and fuel cell activities. For historical context the original Posture Plan issued in 2004 outlined a coordinated plan for DOE and the U.S. Department of Transportation to meet the goals of the Hydrogen Fuel Initiative (HFI) and implement the 2002 National Hydrogen Energy Technology Roadmap. The HFI was launched in 2004 to accelerate research development and demonstration (RD&D) of hydrogen and fuel cell technologies for use in transportation electricity generation and portable power applications. The Roadmap provided a blueprint for the public and private efforts required to fulfill a long-term national vision for hydrogen energy as outlined in A National Vision of America’s Transition to a Hydrogen Economy—to 2030 and Beyond. Both the Roadmap and the Vision were developed out of meetings involving DOE industry academia non-profit organizations and other stakeholders. The Roadmap the Vision the Posture Plans the 2011 Program Plan and the results of key stakeholder workshops continue to form the underlying basis for this current edition of the Program Plan.
This edition of the Program Plan reflects the Department’s focus on conducting coordinated RD&D activities to enable the adoption of hydrogen technologies across multiple applications and sectors. It includes content from the various plans and documents developed by individual offices within DOE working on hydrogen-related activities including: the Office of Fossil Energy's Hydrogen Strategy: Enabling a Low Carbon Economy the Office of Energy Efficiency and Renewable Energy’s Hydrogen and Fuel Cell Technologies Office Multi-year RD&D Plan the Office of Nuclear Energy’s Integrated Energy Systems 2020 Roadmap and the Office of Science’s Basic Research Needs for the Hydrogen Economy. Many of these documents are also in the process of updates and revisions and will be posted online.
Through this overarching document the reader will gain information on the key RD&D needs to enable the largescale use of hydrogen and related technologies—such as fuel cells and turbines—in the economy and how the Department’s various offices are addressing those needs. The Program will continue to periodically revise the Plan along with all program office RD&D plans to reflect technological progress programmatic changes policy decisions and updates based on stakeholder input and reviews.
The 2006 Hydrogen Posture Plan fulfilled the requirement in the Energy Policy Act of 2005 (EPACT 2005) that the Energy Secretary transmit to Congress a coordinated plan for DOE’s hydrogen and fuel cell activities. For historical context the original Posture Plan issued in 2004 outlined a coordinated plan for DOE and the U.S. Department of Transportation to meet the goals of the Hydrogen Fuel Initiative (HFI) and implement the 2002 National Hydrogen Energy Technology Roadmap. The HFI was launched in 2004 to accelerate research development and demonstration (RD&D) of hydrogen and fuel cell technologies for use in transportation electricity generation and portable power applications. The Roadmap provided a blueprint for the public and private efforts required to fulfill a long-term national vision for hydrogen energy as outlined in A National Vision of America’s Transition to a Hydrogen Economy—to 2030 and Beyond. Both the Roadmap and the Vision were developed out of meetings involving DOE industry academia non-profit organizations and other stakeholders. The Roadmap the Vision the Posture Plans the 2011 Program Plan and the results of key stakeholder workshops continue to form the underlying basis for this current edition of the Program Plan.
This edition of the Program Plan reflects the Department’s focus on conducting coordinated RD&D activities to enable the adoption of hydrogen technologies across multiple applications and sectors. It includes content from the various plans and documents developed by individual offices within DOE working on hydrogen-related activities including: the Office of Fossil Energy's Hydrogen Strategy: Enabling a Low Carbon Economy the Office of Energy Efficiency and Renewable Energy’s Hydrogen and Fuel Cell Technologies Office Multi-year RD&D Plan the Office of Nuclear Energy’s Integrated Energy Systems 2020 Roadmap and the Office of Science’s Basic Research Needs for the Hydrogen Economy. Many of these documents are also in the process of updates and revisions and will be posted online.
Through this overarching document the reader will gain information on the key RD&D needs to enable the largescale use of hydrogen and related technologies—such as fuel cells and turbines—in the economy and how the Department’s various offices are addressing those needs. The Program will continue to periodically revise the Plan along with all program office RD&D plans to reflect technological progress programmatic changes policy decisions and updates based on stakeholder input and reviews.
Numerical Simulations of Cryogenic Hydrogen Cooling in Vortex Tubes with Smooth Transitions
Mar 2021
Publication
Improving efficiency of hydrogen cooling in cryogenic conditions is important for the wider applications of hydrogen energy systems. The approach investigated in this study is based on a Ranque-Hilsch vortex tube (RHVT) that generates temperature separation in a working fluid. The simplicity of RHVT is also a valuable characteristic for cryogenic systems. In the present work novel shapes of RHVT are computationally investigated with the goal to raise efficiency of the cooling process. Specifically a smooth transition is arranged between a vortex chamber where compressed gas is injected and the main tube with two exit ports at the tube ends. Flow simulations have been carried out using STAR-CCM+ software with the real-gas Redlich-Kwong model for hydrogen at temperatures near 70 K. It is determined that a vortex tube with a smooth transition of moderate size manifests about 7% improvement of the cooling efficiency when compared vortex tubes that use traditional vortex chambers with stepped transitions and a no-chamber setup with direct gas injection.
Effect of Initial Turbulence on Vented Explosion Over Pressures from Lean Hydrogen-air Deflagrations
Sep 2013
Publication
To examine the effect of initial turbulence on vented explosions experiments were performed for lean hydrogen–air mixtures with hydrogen concentrations ranging from 12 to 15% vol. at elevated initial turbulence. As expected it was found that an increase in initial turbulence increased the overall flame propagation speed and this increased flame propagation speed translated into higher peak overpressures during the external explosion. The peak pressures generated by flame–acoustic interactions however did not vary significantly with initial turbulence. When flame speeds measurements were examined it was found that the burning velocity increased with flame radius as a power function of radius with a relatively constant exponent over the range of weak initial turbulence studied and did not vary systematically with initial turbulence. Instead the elevated initial turbulence increased the initial flame propagation velocities of the various mixtures. The initial turbulence thus appears to act primarily by generating higher initial flame wrinkling while having a minimal effect on the growth rate of the wrinkles. For practical purposes of modelling flame propagation and pressure generation in vented explosions the increase in burning velocity due to turbulence is suggested to be approximated by a single constant factor that increases the effective burning velocity of the mixture. When this approach is applied to a previously developed vent sizing correlation the correlation performs well for almost all of the peaks. It was found however that in certain situations this approach significantly under predicts the flame–acoustic peak. This suggests that further research may be necessary to better understand the influence of initial turbulence on the development of flame–acoustic peaks in vented explosions.
Measurements of Effective Diffusion Coefficient of Helium and Hydrogen Through Gypsum
Sep 2011
Publication
An experimental apparatus which was based on the ¼-scale garage previously used for studying helium release and dispersion in our laboratory was used to obtain effective diffusion coefficients of helium and hydrogen (released as forming gas for safety reasons) through gypsum panel. Two types of gypsum panel were used in the experiments. Helium or forming gas was released into the enclosure from a Fischer burner1 located near the enclosure floor for a fixed duration and then terminated. Eight thermal-conductivity sensors mounted at different vertical locations above the enclosure floor were used to monitor the temporal and spatial gas concentrations. An electric fan was used inside the enclosure to mix the released gas to ensure a spatially uniform gas concentration to minimize stratification. The temporal variations of the pressure difference between the enclosure interior and the ambience were also measured. An analytical model was developed to extract the effective diffusion coefficients from the experimental data.
Updated Jet Flame Radiation Modelling with Corrections for Buoyancy and Wind
Sep 2013
Publication
Radiative heat fluxes from small to medium-scale hydrogen jet flames (<10 m) compare favorably to theoretical predictions provided the product species thermal emittance and optical flame thickness are corrected for. However recent heat flux measurements from two large-scale horizontally orientated hydrogen flames (17.4 and 45.9 m respectively) revealed that current methods underpredicted the flame radiant fraction by 40% or more. Newly developed weighted source flame radiation models have demonstrated substantial improvement in the heat flux predictions particularly in the near-field and allow for a sensible way to correct potential ground surface reflective irradiance. These updated methods are still constrained by the fact that the flame is assumed to have a linear trajectory despite buoyancy effects that can result in significant flame deformation. The current paper discusses a method to predict flame centerline trajectories via a one-dimensional flame integral model which enables optimized placement of source emitters for weighted multi-source heat flux prediction methods. Flame shape prediction from choked releases was evaluated against flame envelope imaging and found to depend heavily on the notional nozzle model formulation used to compute the density weighted effective nozzle diameter. Nonetheless substantial improvement in the prediction of downstream radiative heat flux values occurred when emitter placement was corrected by the flame integral model regardless of the notional nozzle model formulation used.
Hydrogen Storage in Pure and Boron-Substituted Nanoporous Carbons—Numerical and Experimental Perspective
Aug 2021
Publication
Nanoporous carbons remain the most promising candidates for effective hydrogen storage by physisorption in currently foreseen hydrogen-based scenarios of the world’s energy future. An optimal sorbent meeting the current technological requirement has not been developed yet. Here we first review the storage limitations of currently available nanoporous carbons then we discuss possible ways to improve their storage performance. We focus on two fundamental parameters determining the storage (the surface accessible for adsorption and hydrogen adsorption energy). We define numerically the values nanoporous carbons have to show to satisfy mobile application requirements at pressures lower than 120 bar. Possible necessary modifications of the topology and chemical compositions of carbon nanostructures are proposed and discussed. We indicate that pore wall fragmentation (nano-size graphene scaffolds) is a partial solution only and chemical modifications of the carbon pore walls are required. The positive effects (and their limits) of the carbon substitutions by B and Be atoms are described. The experimental ‘proof of concept’ of the proposed strategies is also presented. We show that boron substituted nanoporous carbons prepared by a simple arc-discharge technique show a hydrogen adsorption energy twice as high as their pure carbon analogs. These preliminary results justify the continuation of the joint experimental and numerical research effort in this field.
Electrolyzers Enhancing Flexibility in Electric Grids
Nov 2017
Publication
This paper presents a real-time simulation with a hardware-in-the-loop (HIL)-based approach for verifying the performance of electrolyzer systems in providing grid support. Hydrogen refueling stations may use electrolyzer systems to generate hydrogen and are proposed to have the potential of becoming smarter loads that can proactively provide grid services. On the basis of experimental findings electrolyzer systems with balance of plant are observed to have a high level of controllability and hence can add flexibility to the grid from the demand side. A generic front end controller (FEC) is proposed which enables an optimal operation of the load on the basis of market and grid conditions. This controller has been simulated and tested in a real-time environment with electrolyzer hardware for a performance assessment. It can optimize the operation of electrolyzer systems on the basis of the information collected by a communication module. Real-time simulation tests are performed to verify the performance of the FEC-driven electrolyzers to provide grid support that enables flexibility greater economic revenue and grid support for hydrogen producers under dynamic conditions. The FEC proposed in this paper is tested with electrolyzers however it is proposed as a generic control topology that is applicable to any load.
Road Map to a US Hydrogen Energy: Reducing Emissions and Driving Growth Across the Nation
Oct 2020
Publication
This US Hydrogen Road Map was created through the collaboration of executives and technical industry experts in hydrogen across a broad range of applications and sectors who are committed to improving the understanding of hydrogen and how to increase its adoption across many sectors of the economy. For the first time this coalition of industry leaders has convened to develop a targeted holistic approach for expanding the use of hydrogen as an energy carrier. Due to great variation among national and state policies infrastructure needs and community interests each state and region of the US will likely have its own specific policies and road maps for implementing hydrogen infrastructure. The West Coast for example has traditionally had progressive policies on reducing transportation emissions so it is likely that hydrogen will scale sooner for vehicles in this region especially California. Experts also acknowledge the role that hydrogen in combination with renewables can play in supplying microgrid-type power to communities with the highest risk of shut-offs during seasonal weather-related issues such as high temperatures or wildfire-related power interruptions. Some states have emphasized the need to decarbonize the gas grid so blending hydrogen in natural gas networks and using hydrogen as feedstock may advance more quickly in these regions. Other states are interested in hydrogen as a means to address power grid issues enable the deployment of renewables and support competitive nuclear power. The launch of hydrogen technologies in some states or regions will help to scale hydrogen in various applications across the country laying the foundation for energy security grid resiliency economic growth and the reduction of both greenhouse gas (GHG) emissions and air pollutants. This report outlines the benefits and impact of fuel cell technologies and hydrogen as a viable solution to the energy challenges facing the US through 2030 and beyond. As such it can serve as the latest comprehensive industry-driven national road map to accelerate and scale up hydrogen in the economy across North America
Evaluation of Safety Distances Related to Unconfined Hydrogen Explosions
Sep 2005
Publication
A simple approximate method for evaluation of blast effects and safety distances for unconfined hydrogen explosions is presented. The method includes models for flame speeds hydrogen distribution blast parameters and blast damage criteria. An example of the application of this methodology for hydrogen releases in three hypothetical obstructed areas with different levels of congestion is presented. The severity of the blast effect of unconfined hydrogen explosions is shown to depend strongly on the level of congestion for relatively small releases. Extremely large releases of hydrogen are predicted to be less sensitive to the congestion level.
Analysis of Composite Hydrogen Storage Cylinders under Transient Thermal Loads
Sep 2007
Publication
In order to ensure safe operation of hydrogen storage cylinders under adverse conditions one should be able to predict the extremities under which these cylinders are capable of operating without failing catastrophically. It is therefore necessary to develop a comprehensive model which can predict the behavior and failure of composite storage cylinders when subjected to various types of loading conditions and operating environments. In the present work a finite element model has been developed to analyze composite hydrogen storage cylinders subjected to transient localized thermal loads and internal pressure. The composite cylinder consists of an aluminium liner that serves as a hydrogen gas permeation barrier. A filament-wound carbon/epoxy composite laminate placed over the liner provides the desired load bearing capacity. A glass/epoxy layer or other material is placed over the carbon/epoxy laminate to provide damage resistance for the carbon/epoxy laminates. A doubly curved composite shell element accounting for transverse shear deformation and geometric nonlinearity is used. A temperature dependent material model has been developed and implemented in ABAQUS using user subroutine. A failure model based on Hashin's failure theory is used to predict the various types of failure in the cylinder. A progressive damage model has also been implemented to account for reduction in modulus due to failure. A sublaminate model has been developed to save computational time and reduce the complications in the analysis. A numerical study is conducted to analyze a typical hydrogen storage cylinder and possible failure trends due to localized thermal loading and internal pressure is presented.
The Hydrogen Executive Leadership Panel (HELP) Initiative for Emergency Responder Training
Sep 2007
Publication
In close cooperation with their Canadian counterparts United States public safety authorities are taking the first steps towards creating a proper infrastructure to ensure the safe use of the new hydrogen fuel cells now being introduced commercially. Currently public safety officials are being asked to permit hydrogen fuel cells for stationary power and as emergency power backups for the telecommunications towers that exist everywhere. Consistent application of the safety codes is difficult – in part because it is new – yet it is far more complex to train emergency responders to deal safely with the inevitable hydrogen incidents. The US and Canadian building and fire codes and standards are similar but not identical. The US and Canadian rules are unlikely to be useful to other nations without modification to suit different regulatory systems. However emergency responder safety training is potentially more universal. The risks strategies and tactics are unlikely to differ much by region. The Hydrogen Executive Leadership Panel (HELP) made emergency responder safety training its first priority because the transition to hydrogen depends on keeping incidents small and inoffensive and the public and responders safe from harm. One might think that advising 1.2 million firefighters and 800000 law enforcement officers about hydrogen risks is no more complicated than adding guidance to a website. One would be wrong. The term “training” has specific legal implications which may vary by state. For hazardous materials federal requirements apply. Insurance companies place training requirements on the policies they sell to fire departments including the thousands of small all-volunteer departments which may operate as private corporations. Union contracts may define training and promotions may be based on satisfactorily completed certain levels of training. Emergency responders could no sooner learn how to extinguish a<br/>hydrogen fire by reading a webpage than a person could learn to ride a bicycle by reading a book. Procedures must be learned by listening reading and then doing. Regular practice is necessary. As new hydrogen applications are commercialized additional responder training may be necessary. This highlights another obstacle emergency responders’ ability to travel distances and take the time to undergo training. Historically fire academies established adjunct instructor programs and satellite academies to bring the training to firefighters. The large well-equipped academies are typically used for specialized training. States rarely have enough instructors and instructors often must take the time to create a course outline research each point and produce a program that is informative useful and holds the attention of responders. The challenge of training emergency responders seems next to impossible but public safety authorities are asked to tackle the impossible every day and a model exists to move forward in the U.S. Over the past few years the National Association of State Fire Marshals and U.S. Department of Transportation enlisted the help of emergency responders and industry to create a standardized approach to train emergency responders to deal with pipeline incidents. A curriculum and training materials were created and more than 26000 sets have been distributed for free to public safety agencies nationwide. More than 8000 instructors have been trained to use these materials that are now part of the regular training in 23 states. Using this model HELP intends to ensure that all emergency responders are trained to address hydrogen risks. The model and the rigorous scenario analysis and review used to developing the operational and technical training is addressed in this paper.
Vented Explosion Overpressures From Combustion of Hydrogen and Hydrocarbon Mixtures
Sep 2009
Publication
Experimental data obtained for hydrogen mixtures in a room-size enclosure are presented and compared with data for propane and methane mixtures. This set of data was also used to develop a three-dimensional gas dynamic model for the simulation of gaseous combustion in vented enclosures. The experiments were performed in a 64 m3 chamber with dimensions of 4.6 × 4.6 × 3.0 m and a vent opening on one side and vent areas of either 2.7 or 5.4 m2 were used. Tests were performed for three ignition locations at the wall opposite the vent at the center of the chamber or at the center of the wall containing the vent. Hydrogen–air mixtures with concentrations close 18% vol. were compared with stoichiometric propane–air and methane–air mixtures. Pressure data as function of time and flame time-of-arrival data were obtained both inside and outside the chamber near the vent. Modelling was based on a Large Eddy Simulation (LES) solver created using the OpenFOAM CFD toolbox using sub-grid turbulence and flame wrinkling models. A comparison of these simulations with experimental data is discussed.
First Responder Training Supporting Commercialization of Hydrogen and Fuel Cell Technologies
Oct 2015
Publication
A properly trained first responder community is critical to the successful introduction of hydrogen fuel cell applications and their transformation in how we use energy. Providing resources with accurate information and current knowledge is essential to the delivery of effective hydrogen and fuel cell-related first responder training. The California Fuel Cell Partnership and the Pacific Northwest National Laboratory have over 15 years of experience in developing and delivering hydrogen safety-related first responder training materials and programs. A National Hydrogen and Fuel Cell Emergency Response Training Resource was recently released. This training resource serves the delivery of a variety of training regimens. Associated materials are adaptable for different training formats ranging from high-level overview presentations to more comprehensive classroom training. This paper presents what has been learned from the development and delivery of hydrogen safety-related first responder training programs (online classroom hands-on) by the respective organizations. The collaborative strategy being developed for enhancing training materials and methods for greater accessibility based on stakeholder input will be discussed.
Experimental Investigation of Spherical-flame Acceleration in Lean Hydrogen-air Mixtures
Oct 2015
Publication
Large-scale experiments examining spherical-flame acceleration in lean hydrogen-air mixtures were performed in a 64 m3 constant-pressure enclosure. Equivalence ratios ranging from 0.33 to 0.57 were examined using detailed front tracking for flame diameters up to 1.2 m through the use of a Background Oriented Schlieren (BOS) technique. From these measurements the critical radii for onset of instability for these mixtures on the order of 2–3 cm were obtained. In addition the laminar burning velocity and rate of flame acceleration as a function of radius were also measured.
Effect of Hydrogen Concentration on Vented Explosion Overpressures from Lean Hydrogen–air Deflagrations
Sep 2011
Publication
Experimental data from vented explosion tests using lean hydrogen–air mixtures with concentrations from 12 to 19% vol. are presented. A 63.7-m3 chamber was used for the tests with a vent size of either 2.7 or 5.4 m2. The tests were focused on the effect of hydrogen concentration ignition location vent size and obstacles on the pressure development of a propagating flame in a vented enclosure. The dependence of the maximum pressure generated on the experimental parameters was analyzed. It was confirmed that the pressure maxima are caused by pressure transients controlled by the interplay of the maximum flame area the burning velocity and the overpressure generated outside of the chamber by an external explosion. A model proposed earlier to estimate the maximum pressure for each of the main pressure transients was evaluated for the various hydrogen concentrations. The effect of the Lewis number on the vented explosion overpressure is discussed.
Use of Hydrogen Safety Sensors Under Anaerobic Conditions – Impact of Oxygen Content on Sensor Performance
Sep 2011
Publication
In any application involving the production storage or use of hydrogen sensors are important devices for alerting to the presence of leaked hydrogen. Hydrogen sensors should be accurate sensitive and specific as well as resistant to long term drift and varying environmental conditions. Furthermore as an integral element in a safety system sensor performance should not be compromised by operational parameters. For example safety sensors may be required to operate at reduced oxygen levels relative to air. In this work we evaluate and compare a number of sensor technologies in terms of their ability to detect hydrogen under conditions of varying oxygen concentration.
Overview of the DOE Hydrogen Safety, Codes and Standards Program Part 1- Regulations, Codes and Standards (RCS) for Hydrogen Technologies - An Historical Overview
Oct 2015
Publication
RCS for hydrogen technologies were first developed approximately sixty years ago when hydrogen was being sold as an industrial commodity. The advent of new hydrogen technologies such as Fuel Cell Electric Vehicles (FCEVs) created a need for new RCS. These RCS have been developed with extensive support from the US DOE. These new hydrogen technologies are approaching commercial deployment and this process will produce information on RCS field performance that will create more robust RCS.
Hypothetical Accident Scenario Modelling for Condensed Hydrogen Storage Materials
Sep 2011
Publication
Hydrogen is seen as an ideal energy carrier for stationary and mobile applications. However the use of high energy density condensed hydrogen storage materials such as NH3BH3 comes with risks associated with their high reactivity with water exposure and their decomposition products reactivity in air. To predict their behaviour under these circumstances idealized finite element models of hypothetical accident scenarios have been developed. Empirical thermodynamic calculations based on precise thermal gravimetric analysis (TGA) and calorimetric experiments have been performed in order to quantify the energy and hydrogen release rates and to quantify the reaction products resulting from water and air exposure.
Discussion of Lessons Learned from a Hydrogen Release
Sep 2013
Publication
Just in line with any emerging alternative transportation fuel incidents involving hydrogen used as transportation fuel are learning opportunities for this new and growing industry. This paper includes discussion of many topics in hydrogen safety surrounding the installation operation and maintenance of commercial hydrogen stations or compression storage and dispensing systems.
Applying Risk Management Strategies Prudently
Sep 2011
Publication
During the current global financial crisis the term “Risk Management” is often heard. Just as the causes for the financial problems are elusive so is a complete definition of what Risk Management means. The answer is highly dependent upon your perceptions of “risk” and your appetite for assuming risks. The proposed paper will explore these issues with some brief case studies as they apply to hydrogen industrial applications hydrogen refuelling stations and fuel cell technologies for distributed generation.
Specifically the paper will identify the various risk exposures from the perspective of the project developers original equipment suppliers end users project funding sources and traditional insurance providers. What makes this evaluation intriguing is that it is a mixed bag of output capacities Combine Heat & Power (CHP) potential and technology maturity. Therefore the application considerations must be part of any overall Risk Management program.
Specifically the paper will identify the various risk exposures from the perspective of the project developers original equipment suppliers end users project funding sources and traditional insurance providers. What makes this evaluation intriguing is that it is a mixed bag of output capacities Combine Heat & Power (CHP) potential and technology maturity. Therefore the application considerations must be part of any overall Risk Management program.
Introduction to Hydrogen Safety Engineering
Sep 2011
Publication
The viability and public acceptance of the hydrogen and fuel cell (HFC) systems and infrastructure depends on their robust safety engineering design education and training of the workforce regulators and other stakeholders in the state-of-the-art in the field. This can be provided only through building up and maturity of the hydrogen safety engineering (HSE) profession. HSE is defined as an application of scientific and engineering principles to the protection of life property and environment from adverse effects of incidents/accidents involving hydrogen. This paper describes a design framework and overviews a structure and contents of technical sub-systems for carrying out HSE. The approach is similar to British standard BS7974 for application of fire safety engineering to the design of buildings and expanded to reflect on specific for hydrogen safety related phenomena including but not limited to high pressure under-expanded leaks and dispersion spontaneous ignition of sudden hydrogen releases to air deflagrations and detonations etc. The HSE process includes three main steps. Firstly a qualitative design review is undertaken by a team that can incorporate owner hydrogen safety engineer architect representatives of authorities having jurisdiction e.g. fire services and other stakeholders. The team defines accident scenarios suggests trial safety designs and formulates acceptance criteria. Secondly a quantitative safety analysis of selected scenarios and trial designs is carried out by qualified hydrogen safety engineer(s) using the state-of-the-art knowledge in hydrogen safety science and engineering and validated models and tools. Finally the performance of a HFC system and/or infrastructure under the trial safety designs is assessed against predefined by the team acceptance criteria. This performance-based methodology offers the flexibility to assess trial safety designs using separately or simultaneously three approaches: deterministic comparative or combined probabilistic/deterministic.
Advancing the Hydrogen Safety Knowledge Base
Sep 2013
Publication
The International Energy Agency's Hydrogen Implementing Agreement (IEA HIA) was established in 1977 to pursue collaborative hydrogen research and development and information exchange among its member countries. Information and knowledge dissemination is a key aspect of the work within IEA HIA tasks and case studies technical reports and presentations/publications often result from the collaborative efforts. The work conducted in hydrogen safety under Task 31 and its predecessor Task 19 can positively impact the objectives of national programs even in cases for which a specific task report is not published. The interactions within Task 31 illustrate how technology information and knowledge exchange among participating hydrogen safety experts serve the objectives intended by the IEA HIA.
Achieving High-rate Hydrogen Recovery from Wastewater Using Customizable Alginate Polymer Gel Matrices Encapsulating Biomass
Jul 2018
Publication
In addition to methane gas higher-value resources such as hydrogen gas are produced during anaerobic wastewater treatment. They are however immediately consumed by other organisms. To recover these high-value resources not only do the desired phenotypes need to be retained in the anaerobic reactor but the undesired ones need to be washed out. In this study a well-established alginate-based polymer gel with and without a coating layer was used to selectively encapsulate hydrogen-producing biomass in beads to achieve high-rate recovery of hydrogen during anaerobic wastewater treatment. The effect of cross-linking agents Ca2+ Sr2+ and Ba2+ as well as a composite coating on the beads consisting of alternating layers of polyethylenimine and silica hydrogel were investigated with respect to their performance specifically their mass transfer characteristics and their differential ability to retain the encapsulated biomass. Although the coating reduced the escape rate of encapsulated biomass from the beads all alginate polymer matrices without coating effectively retained biomass. Fast diffusion of dissolved organic carbon (DOC) through the polymer gel was observed in both Ca-alginate and Sr-alginate without coating. The coating however decreased either the diffusivity or the permeability of the DOC depending on whether the DOC was from synthetic wastewater (more lipids and proteins) or real brewery wastewater (more sugars). Consequently the encapsulation system with coating became diffusion limited when brewery wastewater with high chemical oxygen demand was fed resulting in a lower hydrogen production rate than the uncoated encapsulation systems. In all cases the encapsulated biomass was able to produce hydrogen even at a hydraulic residence time of 45 min. Although there are limitations to this system the used of encapsulated biomass for resource recovery from wastewater shows promise particularly for high-rate systems in which the retention of specific phenotypes is desired.
Fundamental Combustion Properties of Oxygen Enriched Hydrogen-air Mixtures Relevant to Safety Analysis Experimental and Simulation Study
Oct 2015
Publication
In order to face the coming shortage of fossil energies a number of alternative methods of energy production are being considered. One promising approach consists in using hydrogen in replacement of the conventional fossil fuels or as an additive to these fuels. In addition to conventional hydro-electric and fission-based nuclear plants electric energy could be obtained in the future using nuclear fusion as investigated within the framework of the ITER project International Thermonuclear Experimental Reactor. However the operation of ITER may rise safety problems including the formation of a flammable dust/hydrogen/air atmosphere. A first step towards the accurate assessment of accidental explosion in ITER consists in better characterizing the risk of explosion in gaseous hydrogen-containing mixtures. In the present study laminar burning speeds ignition delay-times behind reflected shock wave and detonation cell sizes were measured over wide ranges of composition and equivalence ratios. The performances of five detailed reaction models were evaluated with respect to the present data.
Understanding Composition–property Relationships in Ti–Cr–V–Mo Alloys for Optimisation of Hydrogen Storage in Pressurised Tanks
Jun 2014
Publication
The location of hydrogen within Ti–Cr–V–Mo alloys has been investigated during hydrogen absorption and desorption using in situ neutron powder diffraction and inelastic neutron scattering. Neutron powder diffraction identifies a low hydrogen equilibration pressure body-centred tetragonal phase that undergoes a martensitic phase transition to a face-centred cubic phase at high hydrogen equilibration pressures. The average location of the hydrogen in each phase has been identified from the neutron powder diffraction data although inelastic neutron scattering combined with density functional theory calculations show that the local structure is more complex than it appears from the average structure. Furthermore the origin of the change in dissociation pressure and hydrogen trapping on cycling in Ti–Cr–V–Mo alloys is discussed.
The Hydrogen Safety Program of the US Department of Energy
Sep 2005
Publication
Demonstrated safety in the production distribution and use of hydrogen will be critical to successful implementation of a hydrogen infrastructure. Recognizing the importance of this issue the U.S. Department of Energy has established the Hydrogen Safety Program to ensure safe operations of its hydrogen research and development program as well as to identify and address needs for new knowledge and technologies in the future hydrogen economy. Activities in the Safety Program range across the entire safety spectrum including: R&D devoted to investigation of hydrogen behaviour physical characteristics materials compatibility and risk analysis; inspection and investigation into the safety procedures and practices of all hydrogen projects supported by DOE funds; development of critical technologies for safe hydrogen systems such as sensors and design techniques; and safety training and education for emergency responders code inspectors and the general public. Throughout its activities the Safety Program encourages the open sharing of information to enable widespread benefit from any lessons learned or new information developed.
This paper provides detailed descriptions of the various activities of the DOE Hydrogen Safety Program and includes some example impacts already achieved from its implementation.
This paper provides detailed descriptions of the various activities of the DOE Hydrogen Safety Program and includes some example impacts already achieved from its implementation.
Hydrogen Safety Training for Laboratory Researchers and Technical Personnel
Sep 2011
Publication
We have developed a web-based hydrogen safety class and are developing a hands-on hydrogen safety class. The 4-h web-based class is directed to laboratory researchers who need basic hydrogen safety information (free online access at http://www.h2labsafety.org/) and it addresses hydrogen fundamentals: properties pressure and cryogenic safety emergency response and codes and standards. Technical operators in charge of building and testing experimental hydrogen equipment will also soon benefit from a more comprehensive 3-day hands-on safety class that will present detailed information for installation testing and operation of hydrogen pressurized systems. The hands-on class includes a full day of classroom instruction followed by two days of laboratory work where students assemble test and operate a pressure system based on a schematic and component description.
Risk Mitigation Strategies for Hydrogen Storage Materials
Sep 2011
Publication
Hydrogen is seen as an ideal energy carrier for stationary and mobile applications. However the use of high energy density materials such as hydrides comes with the drawback of risks associated to their high reactivity towards air and water exposure. We have developed novel strategies to mitigate these risks. These strategies were evaluated using standard UN tests and isothermal calorimetric measurements. Cycling experiments were conducted to assess the impact of the mitigants on the modified materials derived from 8LiH•3Mg(NH2)2 system. In some cases our results show an improvement in kinetics when compared to the unmodified material. Effective mitigants were also discovered for aluminium hydride (alane) and lithium borohydride completely inhibiting ignition.
Development of Standards for Evaluating Materials Compatibility with High-pressure Gaseous Hydrogen
Sep 2013
Publication
The Hydrogen Safety Codes and Standards program element of the US Department of Energy's Fuel Cell Technologies Office provides coordination and technical data for the development of domestic and international codes and standards related to hydrogen technologies. The materials compatibility program task at Sandia National Laboratories (Livermore CA) is focused on developing the technical basis for qualifying materials for hydrogen service i.e. accommodating hydrogen embrittlement. This presentation summarizes code development activities for qualifying materials for hydrogen service with emphasis on the scientific basis for the testing methodologies including fracture mechanics based measurements (fracture threshold and fatigue crack growth) total fatigue life measurements and full- scale pressure vessel testing.
Hydrogen Fuel-Cell Forklift Vehicle Releases In Enclosed Spaces
Sep 2011
Publication
Sandia National Laboratories has worked with stakeholders and original equipment manufacturers (OEMs) to develop scientific data that can be used to create risk-informed hydrogen codes and standards for the safe operation of indoor hydrogen fuel-cell forklifts. An important issue is the possibility of an accident inside a warehouse or other enclosed space where a release of hydrogen from the high-pressure gaseous storage tank could occur. For such scenarios computational fluid dynamics (CFD) simulations have been used to model the release and dispersion of gaseous hydrogen from the vehicle and to study the behavior of the ignitable hydrogen cloud inside the warehouse or enclosure. The overpressure arising as a result of ignition and subsequent deflagration of the hydrogen cloud within the warehouse has been studied for different ignition delay times and ignition locations. Both ventilated and unventilated warehouses have been considered in the analysis. Experiments have been performed in a scaled warehouse test facility and compared with simulations to validate the results of the computational analysis.
IPHE Regulations Codes and Standards Working Group-type IV COPV Round Robin Testing
Oct 2015
Publication
This manuscript presents the results of a multi-lateral international activity intended to understand how to execute a cycle stress test as specified in a chosen standard (GTR SAE ISO EIHP …). The purpose of this work was to establish a harmonized test method protocol to ensure that the same results would be achieved regardless of the testing facility. It was found that accurate temperature measurement of the working fluid is necessary to ensure the test conditions remain within the tolerances specified. Continuous operation is possible with adequate cooling of the working fluid but this becomes more demanding if the cycle frequency increases. Recommendations for future test system design and operation are presented.
Experimental Investigation of Hydrogen Release and Ignition from Fuel Cell Powered Forklifts in Enclosed Spaces
Sep 2011
Publication
Due to rapid growth in the use of hydrogen powered fuel cell forklifts within warehouse enclosures Sandia National Laboratories has worked to develop scientific methods that support the creation of new hydrogen safety codes and standards for indoor refuelling operations. Based on industry stakeholder input conducted experiments were devised to assess the utility of modelling approaches used to analyze potential consequences from ignited hydrogen leaks in facilities certified according to existing code language. Release dispersion and combustion characteristics were measured within a scaled test facility located at SRI International's Corral Hollow Test Site. Moreover the impact of mitigation measures such as active/passive ventilation and pressure relief panels was investigated. Since it is impractical to experimentally evaluate all possible facility configurations and accident scenarios careful characterization of the experimental boundary conditions has been performed so that collected datasets can be used to validate computational modelling approaches.
Ignitability and Mixing of Underexpanded Hydrogen Jets
Sep 2011
Publication
Reliable methods are needed to predict ignition boundaries that result from compressed hydrogen bulk storage leaks without complex modelling. To support the development of these methods a new high-pressure stagnation chamber has been integrated into Sandia National Laboratories’ Turbulent Combustion Laboratory so that relevant compressed gas release scenarios can be replicated. For the present study a jet with a 10:1 pressure ratio issuing from a small 0.75 mm radius nozzle has been examined. Jet exit shock structure was imaged by Schlieren photography while quantitative Planar Laser Rayleigh Scatter imaging was used to measure instantaneous hydrogen mole fractions downstream of the Mach disk. Measured concentration statistics and ignitable boundary predictions compared favorably to analytic reconstructions of downstream jet dispersion behaviour. Model results were produced from subsonic jet dispersion models and by invoking self-similarity jet scaling arguments with length scaling by experimentally measured effective source radii. Similar far field reconstructions that relied on various notional nozzle models to account for complex jet exit shock phenomena failed to satisfactorily predict the experimental findings. These results indicate further notional nozzle refinement is needed to improve the prediction fidelity. Moreover further investigation is required to understand the effect of different pressure ratios on measured virtual origins used in the jet dispersion model.
No more items...