Transmission, Distribution & Storage
Numerical Simulation on the Thermal Dynamic Behavior of Liquid Hydrogen in a Storage Tank for Trailers
Oct 2022
Publication
In the present study a numerical model was established to investigate the thermal dynamic behavior of liquid hydrogen in a 40-foot ISO tank. The volume of fluids (VOF) method was applied to capture the liquid surface and a phase change model was used to describe the evaporation phenomenon of hydrogen. The mesh independence analysis and the experimental validation have been made. Under different filling levels motion statuses and heat leakage conditions the variations in pressure and temperature of the tank were investigated. The pressure of 90% filling level case was reduced by 12.09% compared to the 50% case. Besides the pressure of the sloshing condition has increased twofold contrasted with the stationary one and thermal stratification disappeared. Additionally 16.67 minutes were taken for the ullage pressure to reach around 1MPa in emergencies of being extremely heated. Some valuable conclusions and suggestions for the transportation of liquid hydrogen arrived. Those could be the references to predict the release time of boil-off hydrogen and primarily support for gas-releasing control strategies.
The Influence of the First Filling Period Length and Reservoir Level Depth on the Operation of Underground Hydrogen Storage in a Deep Aquifer
Sep 2022
Publication
Underground storage is a method of storing large amounts of renewable energy that can be converted into hydrogen. One of the fundamental problems associated with this process concerns determining the timing and amount of injected gas in the first filling period for the operation of an underground storage facility. Ascertaining the hydrogen flow rate is essential to ensure that the capillary and fracturing pressures are not exceeded. The value of the flow rate was assessed by modelling the injection of hydrogen into a deep aquifer. The best initial H2 injection period was found to be five months. The volume of the cushion gas and the total storage capacity expanded with the extension of the first filling period length. The working capacity grew as the depth increased reaching maximum values at depths of approximately 1200e1400 m. This depth was considered optimal for storing hydrogen in the analysed structure.
Increasing the Energy Efficiency of Gas Boosters for Hydrogen Storage and for Refueling Stations
Feb 2023
Publication
A new electrically driven gas booster is described as an alternative to the classical air-driven gas boosters known for their poor energetic efficiency. These boosters are used in small scale Hydrogen storage facilities and in refueling stations for Hydrogen vehicles. In such applications the overall energy count is of significance and must include the efficiency of the compression stage. The proposed system uses an electric motor instead of the pneumatic actuator and increases the total efficiency of the compression process. Two mechanical principles are studied for the transformation of the rotational motion of the motor to the linear displacement of the compressor pistons. The strongly fluctuating power of the compressor is smoothed by an active capacitive auxiliary storage device connected to the DC circuit of the power converter. The proposed system has been verified by numeric simulation including the thermodynamic phenomena the kinetics of the new compressor drive and the the operation of the circuits of the power smoothing system.
Refurbishment of Natural Gas Pipelines towards 100% Hydrogen—A Thermodynamic-Based Analysis
Dec 2022
Publication
Hydrogen is a key enabler of a sustainable society. Refurbishment of the existing natural gas infrastructure for up to 100% H2 is considered one of the most energy- and resource-efficient energy transportation methods. The question remains whether the transportation of 100% H2 with reasonable adaptions of the infrastructure and comparable energy amounts to natural gas is possible. The well-known critical components for refurbishment such as increased compressor power reduced linepack as well as pipeline transport efficiencies and their influencing factors were considered based on thermodynamic calculations with a step-by-step overview. A H2 content of 20–30% results in comparable operation parameters to pure natural gas. In addition to transport in pipelines decentralized H2 production will also play an important role in addressing future demands.
Combined Effects of Stress and Temperature on Hydrogen Diffusion in Non-hydride Forming Alloys Applied in Gas Turbines
Jul 2022
Publication
Hydrogen plays a vital role in the utilisation of renewable energy but ingress and diffusion of hydrogen in a gas turbine can induce hydrogen embrittlement on its metallic components. This paper aims to investigate the hydrogen transport in a non-hydride forming alloy such as Alloy 690 used in gas turbines inspired by service conditions of turbine blades i.e. under the combined effects of stress and temperature. An appropriate hydrogen transport equation is formulated accounting for both stress and temperature distributions of the domain in the non-hydride forming alloy. Finite element (FE) analyses are performed to predict steady-state hydrogen distribution in lattice sites and dislocation traps of a double notched specimen under constant tensile load and various temperature fields. Results demonstrate that the lattice hydrogen concentration is very sensitive to the temperature gradients whilst the stress concentration only slightly increases local lattice hydrogen concentration. The combined effects of stress and temperature result in the highest concentration of the dislocation trapped hydrogen in low-temperature regions although the plastic strain is only at a moderate level. Our results suggest that temperature gradients and stress concentrations in turbine blades due to cooling channels and holes make the relatively low-temperature regions susceptible to hydrogen embrittlement.
Hydrogen-Enriched Compressed Natural Gas Network Simulation for Consuming Green Hydrogen Considering the Hydrogen Diffusion Process
Sep 2022
Publication
Transporting green hydrogen by existing natural gas networks has become a practical means to accommodate curtailed wind and solar power. Restricted by pipe materials and pressure levels there is an upper limit on the hydrogen blending ratio of hydrogen-enriched compressed natural gas (HCNG) that can be transported by natural gas pipelines which affects whether the natural gas network can supply energy safely and reliably. To this end this paper investigates the effects of the intermittent and fluctuating green hydrogen produced by different types of renewable energy on the dynamic distribution of hydrogen concentration after it is blended into natural gas pipelines. Based on the isothermal steady-state simulation results of the natural gas network two convection–diffusion models for the dynamic simulation of hydrogen injections are proposed. Finally the dynamic changes of hydrogen concentration in the pipelines under scenarios of multiple green hydrogen types and multiple injection nodes are simulated on a seven-node natural gas network. The simulation results indicate that compared with the solar-power-dominated hydrogen productionblending scenario the hydrogen concentrations in the natural gas pipelines are more uniformly distributed in the wind-power-dominated scenario and the solar–wind power balance scenario. To be specific in the solar-power-dominated scenario the hydrogen concentration exceeds the limit for more time whilst the overall hydrogen production is low and the local hydrogen concentration in the natural gas network exceeds the limit for nearly 50% of the time in a day. By comparison in the wind-power-dominated scenario all pipelines can work under safe conditions. The hydrogen concentration overrun time in the solar–wind power balance scenario is also improved compared with the solar-power-dominated scenario and the limit-exceeding time of the hydrogen concentration in Pipe 5 and Pipe 6 is reduced to 91.24% and 91.99% of the solar-power-dominated scenario. This work can help verify the day-ahead scheduling strategy of the electricity-HCNG integrated energy system (IES) and provide a reference for the design of local hydrogen production-blending systems.
Inspection of Coated Hydrogen Transportation Pipelines
Sep 2023
Publication
The growing need for hydrogen indicates that there is likely to be a demand for transporting hydrogen. Hydrogen pipelines are an economical option but the issue of hydrogen damage to pipeline steels needs to be studied and investigated. So far limited research has been dedicated to determining how the choice of inspection method for pipeline integrity management changes depending on the presence of a coating. Thus this review aims to evaluate the effectiveness of inspection methods specifically for detecting the defects formed uniquely in coated hydrogen pipelines. The discussion will begin with a background of hydrogen pipelines and the common defects seen in these pipelines. This will also include topics such as blended hydrogen-natural gas pipelines. After which the focus will shift to pipeline integrity management methods and the effectiveness of current inspection methods in the context of standards such as ASME B31.12 and BS 7910. The discussion will conclude with a summary of newly available inspection methods and future research directions.
Metal-Hydride-Based Hydrogen Storage as Potential Heat Source for the Cold Start of PEM FC in Hydrogen-Powered Coaches: A Comparative Study of Various Materials and Thermal Management Techniques
Nov 2022
Publication
The successful and fast start-up of proton exchange membrane fuel cells (PEMFCs) at subfreezing temperatures (cold start) is very important for the use of PEMFCs as energy sources for automotive applications. The effective thermal management of PEMFCs is of major importance. When hydrogen is stored in hydride-forming intermetallics significant amounts of heat are released due to the exothermic nature of the reaction. This excess of heat can potentially be used for PEMFC thermal management and to accelerate the cold start. In the current work this possibility is extensively studied. Three hydride-forming intermetallics are introduced and their hydrogenation behavior is evaluated. In addition five thermal management scenarios of the metal hydride beds are studied in order to enhance the kinetics of the hydrogenation. The optimum combination of the intermetallic hydrogenation behavior weight and complexity of the thermal management system was chosen for the study of thermal coupling with the PEMFCs. A 1D GT-SUITE model was built to stimulate the thermal coupling of a 100 kW fuel cell stack with the metal hydride. The results show that the use of the heat from the metal hydride system was able to reduce the cold start by up to 8.2%.
Investigating Hydrogen-Based Non-Conventional Storage for PV Power in Eco-Energetic Optimization of a Multi-Energy System
Dec 2021
Publication
Through the integration of multiple energy carriers with related technologies multi-energy systems (MES) can exploit the synergies coming from their interplay for several benefits towards decarbonization. In such a context inclusion of Power-to-X technologies in periods of excess renewable electricity supply removes the need for curtailment of renewable electricity generation. In order to achieve the environmental benefits of MES without neglecting their economic feasibility the optimal design problem is as crucial as challenging and requires the adoption of a multi-objective approach. This paper extends the results of a previous work by investigating hydrogen-based non-conventional storage for PV power in the eco-energetic optimization of an MES. The system under study consists of a reversible fuel cell (r-SOC) photovoltaic (PV) electric heat pump absorption chiller and thermal storage and allows satisfying the multi-energy needs of a residential end-user. A multi-objective linear problem is established to find the optimal MES configuration including the sizes of the involved technologies with the goal of reducing the total annual cost and the fossil primary energy input. Simulation results are compared with those obtained in previous work with a conventional nanogrid where a combined heat and power (CHP) system with gas-fired internal combustion engine and a battery were present instead of an r-SOC. The optimized configuration of the non-conventional nanogrid allows achieving a maximum primary energy reduction amounting to 66.3% compared to the conventional nanogrid. In the face of the environmental benefits the non-conventional nanogrid leads to an increase in total annual costs which compared to the conventional nanogrid is in the range of 41–65%.
Research on the Sealing Mechanism of Split-Liner High-Pressure Hydrogen Storage Cylinders
Mar 2024
Publication
Hydrogen storage is a crucial factor that limits the development of hydrogen energy. This paper proposes using a split liner for the inner structure of a hydrogen storage cylinder. A self-tightening seal is employed to address the sealing problem between the head and the barrel. The feasibility of this structure is demonstrated through hydraulic pressure experiments. The influence laws of the O-ring compression rate the distance from the straight edge section of the head to the sealing groove and the thickness of the head on the sealing performance of gas cylinders in this sealing structure are revealed using finite elements analysis. The results show that when the gas cylinder is subjected to medium internal pressure the maximum contact stress on the O-ring extrusion deformation sealing surface is greater than the medium pressure. There is sufficient contact width that is the arc length of the part where the stress on the O-ring contact surface is greater than the medium pressure so that it can form a good sealing condition. At the same time increasing the compression ratio of the O-ring and the head’s thickness will help improve the sealing performance and reducing the distance from the straight edge section of the head to the sealing groove will also improve the sealing performance.
Green Synthesis of Olefin-linked Covalent Organic Frameworks for Hydrogen Fuel Cell Applications
Mar 2021
Publication
Green synthesis of crystalline porous materials for energy-related applications is of great significance but very challenging. Here we create a green strategy to fabricate a highly crystalline olefin-linked pyrazine-based covalent organic framework (COF) with high robustness and porosity under solvent-free conditions. The abundant nitrogen sites high hydrophilicity and well-defined one-dimensional nanochannels make the resulting COF an ideal platform to confine and stabilize the H3PO4 network in the pores through hydrogen-bonding interactions. The resulting material exhibits low activation energy (Ea) of 0.06 eV and ultrahigh proton conductivity across a wide relative humidity (10–90 %) and temperature range (25–80 °C). A realistic proton exchange membrane fuel cell using the olefin-linked COF as the solid electrolyte achieve a maximum power of 135 mW cm−2 and a current density of 676 mA cm−2 which exceeds all reported COF materials.
Relevance of Optimized Low-Scale Green H2 Systems in a French Context: Two Case Studies
May 2022
Publication
Hydrogen has been identified as a very promising vector for energy storage especially for heavy mobility applications. For this reason France is making significant investments in this field and use cases need to be evaluated as they are sprouting. In this paper the relevance of H2 in two storage applications is studied: a domestic renewable electricity production system connected to the grid and a collective hydrogen production for the daily bus refill. The investigation consists of the sizing of the system and then the evaluation of its performance according to several criteria depending on case. Optimizations are made using Bayesian and gradient-based methods. Several variations around a central case are explored for both cases to give insights on the impact of the different parameters (location pricing objective etc.) on the performance of the system.Our results show that domestic power-to-power applications (case 1) do not seem to be competitive with electrochemical storage. Meanwhile without any subsidies or incentives such configuration does not allow prosumers to save money (+16% spendings compared to non-equipped dwelling). It remains interesting when self-sufficiency is the main objective (up to 68% of energy is not exchanged). The power-to-gas application (case 2 central case) with a direct use of hydrogen for mobility seems to be more relevant according to our case study we could reach a production cost of green H2 around 5 €/kg similar to the 3–10 $/kg found in literature for 182 houses involved. In both cases H2 follows a yearly cycle charging in summer and discharging in winter (long term storage) due to low conversion efficiency.
Optimal Design of Multi-energy Systems with Seasonal Storage
Oct 2017
Publication
Optimal design and operation of multi-energy systems involving seasonal energy storage are often hindered by the complexity of the optimization problem. Indeed the description of seasonal cycles requires a year-long time horizon while the system operation calls for hourly resolution; this turns into a large number of decision variables including binary variables when large systems are analyzed. This work presents novel mixed integer linear program methodologies that allow considering a year time horizon with hour resolution while significantly reducing the complexity of the optimization problem. First the validity of the proposed techniques is tested by considering a simple system that can be solved in a reasonable computational time without resorting to design days. Findings show that the results of the proposed approaches are in good agreement with the full-scale optimization thus allowing to correctly size the energy storage and to operate the system with a long-term policy while significantly simplifying the optimization problem. Furthermore the developed methodology is adopted to design a multi-energy system based on a neighborhood in Zurich Switzerland which is optimized in terms of total annual costs and carbon dioxide emissions. Finally the system behavior is revealed by performing a sensitivity analysis on different features of the energy system and by looking at the topology of the energy hub along the Pareto sets.
Mg-based Materials for Hydrogen Storage
Aug 2021
Publication
Over the last decade’s magnesium and magnesium based compounds have been intensively investigated as potential hydrogen storage as well as thermal energy storage materials due to their abundance and availability as well as their extraordinary high gravimetric and volumetric storage densities. This review work provides a broad overview of the most appealing systems and of their hydrogenation/dehydrogenation properties. Special emphasis is placed on reviewing the efforts made by the scientific community in improving the material’s thermodynamic and kinetic properties while maintaining a high hydrogen storage capacity.
Coordinated Control Scheme of a Hybrid Renewable Power System Based on Hydrogen Energy Storage
Aug 2021
Publication
An all-weather energy management scheme for island DC microgrid based on hydrogen energy storage is proposed. A dynamic model of a large-scale wind–solar hybrid hydrogen-generation power generation system was established using a quasi-proportional resonance (QPR). We used the distributed Nautilus vertical axis wind power generation system as the main output of the system and it used the photovoltaic and hydrogen energy storage systems as alternative energy sources. Based on meeting the load power requirements and controlling the bus voltage stability we can convert the excess energy of the microgrid to hydrogen energy. With a shortage of load power we can convert the stored hydrogen into electrical energy for the load. Based on the ANSYS FLUENT software platform the feasibility and superiority over large-scale distributed Nautilus vertical axis wind power generation systems are verified. Through the MATLAB/Simulink software platform the effectiveness of the energy management method is verified. The results show that the large-scale distributed Nautilus vertical axis wind power generation system runs well in the energy system produces stable torque produces energy better than other types of wind turbines and has less impact on the power grid. The energy management method can ensure the normal operation of the system 24 h a day under the premise of maintaining the stable operation of the electric hydrogen system without providing external energy.
Criticality and Life-Cycle Assessment of Materials Used in Fuel-Cell and Hydrogen Technologies
Mar 2021
Publication
The purpose of this paper is to obtain relevant data on materials that are the most commonly used in fuel-cell and hydrogen technologies. The focus is on polymer-electrolyte-membrane fuel cells solid-oxide fuel cells polymer-electrolyte-membrane water electrolysers and alkaline water electrolysers. An innovative methodological approach was developed for a preliminary material assessment of the four technologies. This methodological approach leads to a more rapid identification of the most influential or critical materials that substantially increase the environmental impact of fuel-cell and hydrogen technologies. The approach also assisted in amassing the life-cycle inventories—the emphasis here is on the solid-oxide fuel-cell technology because it is still in its early development stage and thus has a deficient materials’ database—that were used in a life-cycle assessment for an in-depth material-criticality analysis. All the listed materials—that either are or could potentially be used in these technologies—were analysed to give important information for the fuel-cell and hydrogen industries the recycling industry the hydrogen economy as well as policymakers. The main conclusion from the life-cycle assessment is that the polymer-electrolyte membrane water electrolysers have the highest environmental impacts; lower impacts are seen in polymer-electrolyte-membrane fuel cells and solid-oxide fuel cells while the lowest impacts are observed in alkaline water electrolysers. The results of the material assessment are presented together for all the considered materials but also separately for each observed technology.
Biological Hydrogen Methanation Systems – An Overview of Design and Efficiency
Oct 2019
Publication
The rise in intermittent renewable electricity production presents a global requirement for energy storage. Biological hydrogen methanation (BHM) facilitates wind and solar energy through the storage of otherwise curtailed or constrained electricity in the form of the gaseous energy vector biomethane. Biological methanation in the circular economy involves the reaction of hydrogen – produced during electrolysis – with carbon dioxide in biogas to produce methane (4H2 + CO2 = CH4 + 2H2) typically increasing the methane output of the biogas system by 70%. In this paper several BHM systems were researched and a compilation of such systems was synthesized facilitating comparison of key parameters such as methane evolution rate (MER) and retention time. Increased retention times were suggested to be related to less efficient systems with long travel paths for gases through reactors. A significant lack of information on gas-liquid transfer co-efficient was identified
Multiscale Modelling of Hydrogen Transport and Segregation in Polycrystalline Steels
Jun 2018
Publication
A key issue in understanding and effectively managing hydrogen embrittlement in complex alloys is identifying and exploiting the critical role of the various defects involved. A chemo-mechanical model for hydrogen diffusion is developed taking into account stress gradients in the material as well as microstructural trapping sites such as grain boundaries and dislocations. In particular the energetic parameters used in this coupled approach are determined from ab initio calculations. Complementary experimental investigations that are presented show that a numerical approach capable of massive scale-bridging up to the macroscale is required. Due to the wide range of length scales accounted for we apply homogenisation schemes for the hydrogen concentration to reach simulation dimensions comparable to metallurgical process scales. Via a representative volume element approach an ab initio based scale bridging description of dislocation-induced hydrogen aggregation is easily accessible. When we extend the representative volume approach to also include an analytical approximation for the ab initio based description of grain boundaries we find conceptual limitations that hinder a quantitative comparison to experimental data in the current stage. Based on this understanding the development of improved strategies for further efficient scale bridging approaches is foreseen.
Recent Progress and New Perspectives on Metal Amide and Imide Systems for Solid-State Hydrogen Storage
Apr 2018
Publication
Hydrogen storage in the solid state represents one of the most attractive and challenging ways to supply hydrogen to a proton exchange membrane (PEM) fuel cell. Although in the last 15 years a large variety of material systems have been identified as possible candidates for storing hydrogen further efforts have to be made in the development of systems which meet the strict targets of the Fuel Cells and Hydrogen Joint Undertaking (FCH JU) and U.S. Department of Energy (DOE). Recent projections indicate that a system possessing: (i) an ideal enthalpy in the range of 20–50 kJ/mol H2 to use the heat produced by PEM fuel cell for providing the energy necessary for desorption; (ii) a gravimetric hydrogen density of 5 wt. % H2 and (iii) fast sorption kinetics below 110 ◦C is strongly recommended. Among the known hydrogen storage materials amide and imide-based mixtures represent the most promising class of compounds for on-board applications; however some barriers still have to be overcome before considering this class of material mature for real applications. In this review the most relevant progresses made in the recent years as well as the kinetic and thermodynamic properties experimentally measured for the most promising systems are reported and properly discussed.
Optical, Electrical and Structural Study of Mg/Ti Bilayer Thin Film for Hydrogen Storage Applications
Apr 2021
Publication
Bilayer Mg/Ti (200 nm) thin films were successfully prepared by using D.C. magnetron sputtering unit. These films were vacuum annealed at 573 K temperature for one hour to obtain homogeneous and intermixed structure of bilayer. Hydrogenation of these thin film structures was made at different hydrogen pressure (15 30 & 45 psi) for 30 min to visualize the effect of hydrogen on film structure. The UV–Vis absorption spectra I-V characteristics and Raman spectroscopy were carried out to study the effect of hydrogen on optical electrical and structural properties of Mg/Ti bilayer thin films. The annealed thin film represents the semiconductor nature with the conductivity of the order of 10-5 Ώ−1-m−1 and it decreases as hydrogen pressure increases. The nonlinear dependence of resistivity on hydrogen pressure reveals inhomogeneous distribution of hydrogen in the thin film. Raman spectroscopy confirmed the presence of hydrogen in thin film where the intensity of peaks was found to be decreased with hydrogen pressure.
Onboard Compressed Hydrogen Storage: Fast Filling Experiments and Simulations
Nov 2021
Publication
Technology safety represents a key enabling factor for the commercial use of hydrogen within the automotive industry. In the last years considerable pre-normative and normative research effort has produced regulations at national European and global level as well as international standards. Their validation is at the moment on going internationally. Additional research is required to improve this regulatory and standardization frame which is also expected to have a beneficial effect on cost and product optimization. The present paper addresses results related to the experimental assessment and modeling of safety performance of high pressure onboard storage. To simulate the lifetime of onboard hydrogen tanks commercial tanks have been subjected to filling-emptying cycles encompassing a fast-filling phase as prescribed by the European regulation on type-approval of hydrogen vehicles. The local temperature history inside the tanks has been measured and compared with the temperature outside at the tank metallic bosses which is the measurement location identified by the regulation. Experimental activities are complemented by computational fluid-dynamics (CFD) modeling of the fast-filling process by means of a numerical model previously validated. The outcome of these activities is a set of scientifically based data which will serve as input to future regulations and standards improvement.
Hydrogen-based Systems for Integration of Renewable Energy in Power Systems: Achievements and Perspectives
Jul 2021
Publication
This paper is a critical review of selected real-world energy storage systems based on hydrogen ranging from lab-scale systems to full-scale systems in continuous operation. 15 projects are presented with a critical overview of their concept and performance. A review of research related to power electronics control systems and energy management strategies has been added to integrate the findings with outlooks usually described in separate literature. Results show that while hydrogen energy storage systems are technically feasible they still require large cost reductions to become commercially attractive. A challenge that affects the cost per unit of energy is the low energy efficiency of some of the system components in real-world operating conditions. Due to losses in the conversion and storage processes hydrogen energy storage systems lose anywhere between 60 and 85% of the incoming electricity with current technology. However there are currently very few alternatives for long-term storage of electricity in power systems so the interest in hydrogen for this application remains high from both industry and academia. Additionally it is expected that the share of intermittent renewable energy in power systems will increase in the coming decades. This could lead to technology development and cost reductions within hydrogen technology if this technology is needed to store excess renewable energy. Results from the reviewed projects indicate that the best solution from a technical viewpoint consists in hybrid systems where hydrogen is combined with short-term energy storage technologies like batteries and supercapacitors. In these hybrid systems the advantages with each storage technology can be fully exploited to maximize efficiency if the system is specifically tailored to the given situation. The disadvantage is that this will obviously increase the complexity and total cost of the energy system.<br/>Therefore control systems and energy management strategies are important factors to achieve optimal results both in terms of efficiency and cost. By considering the reviewed projects and evaluating operation modes and control systems new hybrid energy systems could be tailored to fit each situation and to reduce energy losses.
A Review at the Role of Storage in Energy Systems with a Focus on Power to Gas and Long-term Storage
Aug 2017
Publication
A review of more than 60 studies (plus m4ore than 65 studies on P2G) on power and energy models based on simulation and optimization was done. Based on these for power systems with up to 95% renewables the electricity storage size is found to be below 1.5% of the annual demand (in energy terms). While for 100% renewables energy systems (power heat mobility) it can remain below 6% of the annual energy demand. Combination of sectors and diverting the electricity to another sector can play a large role in reducing the storage size. From the potential alternatives to satisfy this demand pumped hydro storage (PHS) global potential is not enough and new technologies with a higher energy density are needed. Hydrogen with more than 250 times the energy density of PHS is a potential option to satisfy the storage need. However changes needed in infrastructure to deal with high hydrogen content and the suitability of salt caverns for its storage can pose limitations for this technology. Power to Gas (P2G) arises as possible alternative overcoming both the facilities and the energy density issues. The global storage requirement would represent only 2% of the global annual natural gas production or 10% of the gas storage facilities (in energy equivalent). The more options considered to deal with intermittent sources the lower the storage requirement will be. Therefore future studies aiming to quantify storage needs should focus on the entire energy system including technology vectors (e.g. Power to Heat Liquid Gas Chemicals) to avoid overestimating the amount of storage needed.
Development and Future Scope of Renewable Energy and Energy Storage Systems
May 2022
Publication
This review study attempts to summarize available energy storage systems in order to accelerate the adoption of renewable energy. Inefficient energy storage systems have been shown to function as a deterrent to the implementation of sustainable development. It is therefore critical to conduct a thorough examination of existing and soon-to-be-developed energy storage technologies. Various scholarly publications in the fields of energy storage systems and renewable energy have been reviewed and summarized. Data and themes have been further highlighted with the use of appropriate figures and tables. Case studies and examples of major projects have also been researched to gain a better understanding of the energy storage technologies evaluated. An insightful analysis of present energy storage technologies and other possible innovations have been discovered with the use of suitable literature review and illustrations. This report also emphasizes the critical necessity for an efficient storage system if renewable energy is to be widely adopted.
Balancing Wind-power Fluctuation Via Onsite Storage Under Uncertainty Power-to-hydrogen-to-power Versus Lithium Battery
Oct 2019
Publication
Imbalance costs caused by forecasting errors are considerable for grid-connected wind farms. In order to reduce such costs two onsite storage technologies i.e. power-to-hydrogen-to-power and lithium battery are investigated considering 14 uncertain technological and economic parameters. Probability density distributions of wind forecasting errors and power level are first considered to quantify the imbalance and excess wind power. Then robust optimal sizing of the onsite storage is performed under uncertainty to maximize wind-farm profit (the net present value). Global sensitivity analysis is further carried out for parameters prioritization to highlight the key influential parameters. The results show that the profit of power-to-hydrogen-to-power case is sensitive to the hydrogen price wind forecasting accuracy and hydrogen storage price. When hydrogen price ranges in (2 6) €/kg installing only electrolyzer can earn profits over 100 k€/MWWP in 9% scenarios with capacity below 250 kW/MWWP under high hydrogen price (over 4 €/kg); while installing only fuel cell can achieve such high profits only in 1.3% scenarios with capacity below 180 kW/MWWP. Installing both electrolyzer and fuel cell (only suggested in 22% scenarios) results in profits below 160 k€/MWWP and particularly 20% scenarios allow for a profit below 50 k€/MWWP due to the contradictory effects of wind forecasting error hydrogen and electricity price. For lithium battery investment cost is the single highly influential factor which should be reduced to 760 €/kWh. The battery capacity is limited to 88 kW h/MWWP. For profits over 100 k€/MWWP (in 3% scenarios) the battery should be with an investment cost below 510 €/kWh and a depth of discharge over 63%. The power-to-hydrogen-to-power case is more advantageous in terms of profitability reliability and utilization factor (full-load operating hours) while lithium battery is more helpful to reduce the lost wind and has less environmental impact considering current hydrogen market.
Life Cycle Assessment of Hydrogen Transportation Pathways via Pipelines and Truck Trailers: Implications as a Low Carbon Fuel
Sep 2022
Publication
Hydrogen fuel cells have the potential to play a significant role in the decarbonization of the transportation sector globally and especially in California given the strong regulatory and policy focus. Nevertheless numerous questions arise regarding the environmental impact of the hydrogen supply chain. Hydrogen is usually delivered on trucks in gaseous form but can also be transported via pipelines as gas or via trucks in liquid form. This study is a comparative attributional life cycle analysis of three hydrogen production methods alongside truck and pipeline transportation in gaseous form. Impacts assessed include global warming potential (GWP) nitrogen oxide volatile organic compounds and particulate matter 2.5 (PM2.5). In terms of GWP the truck transportation pathway is more energy and ecologically intensive than pipeline transportation despite gaseous truck transport being more economical. A sensitivity analysis of pipeline transportation and life cycle inventories (LCI) attribution is included. Results are compared across multiple scenarios of the production and transportation pathways to discover the strongest candidates for minimizing the environmental footprint of hydrogen production and transportation. The results indicate the less ecologically intensive pathway is solar electrolysis through pipelines. For 1 percent pipeline attribution the total CO2eq produced per consuming 1 MJ of hydrogen in a fuel cell pickup truck along this pathway is 50.29 g.
Quantification of Hydrogen in Nanostructured Hydrogenated Passivating Contacts for Silicon Photovoltaics Combining SIMS-APT-TEM: A Multiscale Correlative Approach
Mar 2021
Publication
Multiscale characterization of the hydrogenation process of silicon solar cell contacts based on c-Si/SiOx/nc-SiCx(p) has been performed by combining dynamic secondary ion mass-spectrometry (D-SIMS) atom probe tomography (APT) and transmission electron microscopy (TEM). These contacts are formed by high-temperature firing which triggers the crystallization of SiCx followed by a hydrogenation process to passivate remaining interfacial defects. Due to the difficulty of characterizing hydrogen at the nm-scale the exact hydrogenation mechanisms have remained elusive. Using a correlative TEM-SIMS-APT analysis we are able to locate hydrogen trap sites and quantify the hydrogen content. Deuterium (D) a heavier isotope of hydrogen is used to distinguish hydrogen introduced during hydrogenation from its background signal. D-SIMS is used due to its high sensitivity to get an accurate deuterium-to-hydrogen ratio which is then used to correct deuterium profiles extracted from APT reconstructions. This new methodology to quantify the concentration of trapped hydrogen in nm-scale structures sheds new insights on hydrogen distribution in technologically important photovoltaic materials.
Green Hydrogen Storage in an Underground Cavern: A Case Study in Salt Diapir of Spain
Jun 2022
Publication
The Poza de la Sal diapir is a closed circular depression with Cretaceous Mesozoic materials formed by gypsum Keuper clays and a large extension of salt in the center with intercalations of ophite. The low seismic activity of the area the reduced permeability and porosity of the salt caverns and the proximity to the Páramo de Poza wind park make it a suitable place for the construction of a facility for underground storage of green hydrogen obtained from surplus wind power. The design of a cavern for hydrogen storage at a depth of 1000 m takes into account the differences in stresses temperatures and confining pressures involved in the salt deformation process. During the 8 months of the injection phase 23.0 GWh can be stored in the form of hydrogen obtained from the wind energy surplus to be used later in the extraction phase. The injection and extraction ratio must be developed under the conditions of geomechanical safety of the cavity so as to minimize the risks to the environment and people by conditioning the gas pressure inside the cavity to remain within a given range.
Wettability of Shale–brine–H2 System and H2-brine Interfacial Tension for Assessment of the Sealing Capacities of Shale Formations During Underground Hydrogen Storage
Jul 2022
Publication
Replacement of fossil fuels with clean hydrogen has been recognized as the most feasible approach of implementing CO2-free hydrogen economy globally. However large-scale storage of hydrogen is a critical component of hydrogen economy value chain because hydrogen is the lightest molecule and has moderately low volumetric energy content. To achieve successful storage of buoyant hydrogen at the subsurface and convenient withdrawal during the period of critical energy demand the integrity of the underground storage rock and overlying seal (caprock) must be assured. Presently there is paucity of information on hydrogen wettability of shale and the interfacial properties of H2/brine system. In this research contact angles of shale/H2/brine system and hydrogen/brine interfacial tension (IFT) were measured using Krüss drop shape analyzer (DSA 100) at 50 ◦C and varying pressure (14.7–1000 psi). A modified form of sessile drop approach was used for the contact angles measurement whereas the H2- brine IFT was measured through the pendant drop method. H2-brine IFT values decreased slightly with increasing pressure ranging between 63.68◦ at 14.7 psia and 51.29◦ at 1000 psia. The Eagle-ford shale with moderate total organic carbon (TOC) of 3.83% attained fully hydrogen-wet (contact angle of 99.9◦ ) and intermediate-wet condition (contact angle of 89.7◦ ) at 14.7 psi and 200 psi respectively. Likewise the Wolf-camp shale with low TOC (0.30%) attained weakly water-wet conditions with contact angles of 58.8◦ and 62.9◦ at 14.7 psi and 200 psi respectively. The maximum height of hydrogen that can be securely trapped by the Wolf-camp shale was approximately 325 meters whereas the value was merely 100 meters for the Eagle-ford shale. Results of this study will aid in assessment of hydrogen storage capacity of organic-rich shale (adsorption trapping) as well as evaluation of the sealing potentials of low TOC shale (caprock) during underground hydrogen storage.
Power-to-Gas and Power-to-X—The History and Results of Developing a New Storage Concept
Oct 2021
Publication
Germany’s energy transition known as ‘Energiewende’ was always very progressive. However it came technically to a halt at the question of large-scale seasonal energy storage for wind and solar which was not available. At the end of the 2000s we combined our knowledge of both electrical and process engineering imitated nature by copying photosynthesis and developed Power-to-Gas by combining water electrolysis with CO2 -methanation to convert water and CO2 together with wind and solar power to synthetic natural gas. Storing green energy by coupling the electricity with the gas sector using its vast TWh-scale storage facility was the solution for the biggest energy problem of our time. This was the first concept that created the term ‘sector coupling’ or ‘sectoral integration’. We first implemented demo sites presented our work in research industry and ministries and applied it in many macroeconomic studies. It was an initial idea that inspired others to rethink electricity as well as eFuels as an energy source and energy carrier. We developed the concept further to include Power-to-Liquid Power-to-Chemicals and other ways to ‘convert’ electricity into molecules and climate-neutral feedstocks and named it ‘Power-to-X’ at the beginning of the 2010s.
Complex Hydrides for Hydrogen Storage – New Perspectives
Apr 2014
Publication
Since the 1970s hydrogen has been considered as a possible energy carrier for the storage of renewable energy. The main focus has been on addressing the ultimate challenge: developing an environmentally friendly successor for gasoline. This very ambitious goal has not yet been fully reached as discussed in this review but a range of new lightweight hydrogen-containing materials has been discovered with fascinating properties. State-of-the-art and future perspectives for hydrogen-containing solids will be discussed with a focus on metal borohydrides which reveal significant structural flexibility and may have a range of new interesting properties combined with very high hydrogen densities.
Simulation of the Inelastic Deformation of Porous Reservoirs Under Cyclic Loading Relevant for Underground Hydrogen Storage
Dec 2022
Publication
Subsurface geological formations can be utilized to safely store large-scale (TWh) renewable energy in the form of green gases such as hydrogen. Successful implementation of this technology involves estimating feasible storage sites including rigorous mechanical safety analyses. Geological formations are often highly heterogeneous and entail complex nonlinear inelastic rock deformation physics when utilized for cyclic energy storage. In this work we present a novel scalable computational framework to analyse the impact of nonlinear deformation of porous reservoirs under cyclic loading. The proposed methodology includes three diferent time-dependent nonlinear constitutive models to appropriately describe the behavior of sandstone shale rock and salt rock. These constitutive models are studied and benchmarked against both numerical and experimental results in the literature. An implicit time-integration scheme is developed to preserve the stability of the simulation. In order to ensure its scalability the numerical strategy adopts a multiscale fnite element formulation in which coarse scale systems with locally-computed basis functions are constructed and solved. Further the efect of heterogeneity on the results and estimation of deformation is analyzed. Lastly the Bergermeer test case—an active Dutch natural gas storage feld—is studied to investigate the infuence of inelastic deformation on the uplift caused by cyclic injection and production of gas. The present study shows acceptable subsidence predictions in this feld-scale test once the properties of the fnite element representative elementary volumes are tuned with the experimental data.
Liquid Hydrogen: A Review on Liquefaction, Storage, Transportation, and Safety
Sep 2021
Publication
Decarbonization plays an important role in future energy systems for reducing greenhouse gas emissions and establishing a zero-carbon society. Hydrogen is believed to be a promising secondary energy source (energy carrier) that can be converted stored and utilized efficiently leading to a broad range of possibilities for future applications. Moreover hydrogen and electricity are mutually converted creating high energy security and broad economic opportunities toward high energy resilience. Hydrogen can be stored in various forms including compressed gas liquid hydrogen hydrides adsorbed hydrogen and reformed fuels. Among these liquid hydrogen has advantages including high gravimetric and volumetric hydrogen densities and hydrogen purity. However liquid hydrogen is garnering increasing attention owing to the demand for long storage periods long transportation distances and economic performance. This paper reviews the characteristics of liquid hydrogen liquefaction technology storage and transportation methods and safety standards to handle liquid hydrogen. The main challenges in utilizing liquid hydrogen are its extremely low temperature and ortho- to para-hydrogen conversion. These two characteristics have led to the urgent development of hydrogen liquefaction storage and transportation. In addition safety standards for handling liquid hydrogen must be updated regularly especially to facilitate massive and large-scale hydrogen liquefaction storage and transportation.
Optimal Design of Stand-alone Solutions Based on RES + Hydrogen Storage Feeding Off-grid Communities
Apr 2021
Publication
Concerning off-grid areas diesel engines still dominate the scene of local electricity generation despite the related pollution concerns and high operating costs. There is thus a huge global potential in remote areas for exploiting local renewable energy sources (RES) in place of fossil generation. Energy storage systems become hence essential for off-grid communities to cope with the issue of RES intermittency allowing them to rely on locally harvested RES. In this work we analysed different typologies of off-grid renewable power systems involving batteries and hydrogen as means to store energy to find out which is the most cost-effective configuration in remote areas. Both Li-ion and lead-acid batteries were included in the analysis and both alkaline and PEM electrolysis technologies were considered for the production of hydrogen. Starting from single cell electrochemical models the performance curves of the electrolyser and fuel cell devices were derived for a more detailed techno-economic assessment. Lifetimes of batteries and H2-based components were also computed based on how the power-to-power (P2P) system operates along the reference year. The particle swarm optimization (PSO) algorithm was employed to find the component sizes that allow minimizing the levelized cost of energy (LCOE) while keeping the off-grid area energy autonomous. As a case study the Ginostra village on the island of Stromboli (North of Sicily Southern Italy) was analysed since it is well representative of small insular locations in the Mediterranean area. The renewable P2P solution (0.51 €/kWh for the cheapest configuration) was found to be economically preferable than the current existing power system relying on diesel generators (0.86 €/kWh). Hydrogen in particular can prevent the oversizing of both battery and PV systems thus reducing the final cost of electricity delivered by the P2P system. Moreover unlike diesel generators the RES-based configuration allows avoiding the production of local air pollutants and GHG emissions during its operation.
Seasonal Storage and Alternative Carriers: A Flexible Hydrogen Supply Chain Model
May 2017
Publication
A viable hydrogen infrastructure is one of the main challenges for fuel cells in mobile applications. Several studies have investigated the most cost-efficient hydrogen supply chain structure with a focus on hydrogen transportation. However supply chain models based on hydrogen produced by electrolysis require additional seasonal hydrogen storage capacity to close the gap between fluctuation in renewable generation from surplus electricity and fuelling station demand. To address this issue we developed a model that draws on and extends approaches in the literature with respect to long-term storage. Thus we analyse Liquid Organic Hydrogen Carriers (LOHC) and show their potential impact on future hydrogen mobility. We demonstrate that LOHC-based pathways are highly promising especially for smaller-scale hydrogen demand and if storage in salt caverns remains uncompetitive but emit more greenhouse gases (GHG) than other gaseous or hydrogen ones. Liquid hydrogen as a seasonal storage medium offers no advantage compared to LOHC or cavern storage since lower electricity prices for flexible operation cannot balance the investment costs of liquefaction plants. A well-to-wheel analysis indicates that all investigated pathways have less than 30% GHG-emissions compared to conventional fossil fuel pathways within a European framework.
Production Costs for Synthetic Methane in 2030 and 2050 of an Optimized Power-to-Gas Plant with Intermediate Hydrogen Storage
Aug 2019
Publication
The publication gives an overview of the production costs of synthetic methane in a Power-to-Gas process. The production costs depend in particularly on the electricity price and the full load hours of the plant sub-systems electrolysis and methanation. The full-load hours of electrolysis are given by the electricity supply concept. In order to increase the full-load hours of methanation the size of the intermediate hydrogen storage tank and the size of the methanation are optimised on the basis of the availability of hydrogen. The calculation of the production costs for synthetic methane are done with economics for 2030 and 2050 and the expenditures are calculated for one year of operation. The sources of volume of purchased electricity are the short-term market long-term contracts direct-coupled renewable energy sources or seasonal use of surpluses. Gas sales are either traded on the short-term market or guaranteed by long-term contracts. The calculations show that an intermediate storage tank for hydrogen adjustment of the methanation size and operating electrolysis and methanation separately increase the workload of the sub-system methanation. The gas production costs can be significantly reduced. With the future expected development of capital expenditures operational expenditure electricity prices gas costs and efficiencies an economic production of synthetic natural gas for the years 2030 especially for 2050 is feasible. The results show that Power-to-Gas is an option for long-term large-scale seasonal storage of renewable energy. Especially the cases with high operating hours for the sub-system methanation and low electricity prices show gas production costs below the expected market prices for synthetic gas and biogas.
Resilience-oriented Schedule of Microgrids with Hybrid Energy Storage System using Model Predictive Control
Nov 2021
Publication
Microgrids can be regarded as a promising solution by which to increase the resilience of power systems in an energy paradigm based on renewable generation. Their main advantage is their ability to work as islanded systems under power grid outage conditions. Microgrids are usually integrated into electrical markets whose schedules are carried out according to economic aspects while resilience criteria are ignored. This paper shows the development of a resilience-oriented optimization for microgrids with hybrid Energy Storage System (ESS) which is validated via numerical simulations. A hybrid ESS composed of hydrogen and batteries is therefore considered with the objective of improving the autonomy of the microgrid while achieving a rapid transition response. The control problem is formulated using Stochastic Model Predictive Control (SMPC) techniques in order to take into account possible transitions between grid-connected and islanded modes at all the sample instants of the schedule horizon (SH). The control problem is developed by considering a healthy operation of the hybrid ESS thus avoiding degradation issues. The plant is modeled using the Mixed Logic Dynamic (MLD) framework owing to the presence of logic and dynamic control variables.
Boron Hydrogen Compounds: Hydrogen Storage and Battery Applications
Dec 2021
Publication
About 25 years ago Bogdanovic and Schwickardi (B. Bogdanovic M. Schwickardi: J. Alloys Compd. 1–9 253 (1997) discovered the catalyzed release of hydrogen from NaAlH4 . This discovery stimulated a vast research effort on light hydrides as hydrogen storage materials in particular boron hydrogen compounds. Mg(BH4 )2 with a hydrogen content of 14.9 wt % has been extensively studied and recent results shed new light on intermediate species formed during dehydrogenation. The chemistry of B3H8 − which is an important intermediate between BH4 − and B12H12 2− is presented in detail. The discovery of high ionic conductivity in the high-temperature phases of LiBH4 and Na2B12H12 opened a new research direction. The high chemical and electrochemical stability of closo-hydroborates has stimulated new research for their applications in batteries. Very recently an all-solid-state 4 V Na battery prototype using a Na4 (CB11H12)2 (B12H12) solid electrolyte has been demonstrated. In this review we present the current knowledge of possible reaction pathways involved in the successive hydrogen release reactions from BH4 − to B12H12 2− and a discussion of relevant necessary properties for high-ionic-conduction materials.
The Effect of Heat Treatments on the Constituent Materials of a Nuclear Reactor Pressure Vessel in Hydrogen Environment
Jul 2016
Publication
A nuclear reactor pressure vessel (NRPV) wall is formed by two layer of different materials: an inner layer of stainless steel (cladding material) and an outer layer of low carbon steel (base material) which is highly susceptible to corrosion related phenomena. A reduction of the mechanical properties of both materials forming the wall would appear due to the action of the harsh environment causing hydrogen embrittlement (HE) related phenomena. As a result of the manufacturing process residual stresses and strains appear in the NRPV wall thereby influencing the main stage in HE: hydrogen diffusion. A common engineering practice for reducing such states is to apply a tempering heat treatment. In this paper a numerical analysis is carried out for revealing the influence of the heat treatment parameters (tempering temperature and tempering time) on the HE of a commonly used NRPV. To achieve this goal a numerical model of hydrogen diffusion assisted by stress and strain was used considering diverse residual stress-strain states after tempering. This way the obtained hydrogen accumulation during operation time of the NRPV provides insight into the better tempering conditions from the structural integrity point of view.
Techno-economic Assessment of Low-carbon Hydrogen Export from Western Canada to Eastern Canada, the USA, the Asia-Pacific, and Europe
Dec 2021
Publication
The use of low-carbon hydrogen is being considered to help decarbonize several jurisdictions around the world. There may be opportunities for energy-exporting countries to supply energy-importing countries with a secure source of low-carbon hydrogen. The study objective is to assess the delivered cost of gaseous hydrogen export from Canada (a fossil-resource rich country) to the Asia-Pacific Europe and inland destinations in North America. There is a data gap on the feasibility of inter-continental export of hydrogen from an energy-producing jurisdiction to energy-consuming jurisdictions. This study is aimed at addressing this gap and includes an assessment of opportunities across the Pacific Ocean and the Atlantic Ocean based on fundamental engineering-based models. Techno-economics were used to determine the delivered cost of hydrogen to these destinations. The modelling considers energy material and capacity-sizing requirements for a five-stage supply chain comprising hydrogen production with carbon capture and storage hydrogen pipeline transportation liquefaction shipping and regasification at the destinations. The results show that the delivered cost of hydrogen to inland destinations in North America is between CAD$4.81/kg and CAD$6.03/kg to the Asia-Pacific from CAD$6.65/kg to CAD$6.99/kg and at least CAD$8.14/kg for exports to Europe. Delivering hydrogen by blending in existing long-distance natural gas pipelines reduced the delivered cost to inland destinations by 17%. Exporting ammonia to the Asia-Pacific provides cost savings of 28% compared to shipping liquified hydrogen. The developed information may be helpful to policymakers in government and the industry in making informed decisions about international trade of low-carbon hydrogen in both energy-exporting and energy-importing jurisdictions globally.
New Liquid Chemical Hydrogen Storage Technology
Aug 2022
Publication
The liquid chemical hydrogen storage technology has great potentials for high-density hydrogen storage and transportation at ambient temperature and pressure. However its commercial applications highly rely on the high-performance heterogeneous dehydrogenation catalysts owing to the dehydrogenation difficulty of chemical hydrogen storage materials. In recent years the chemists and materials scientists found that the supported metal nanoparticles (MNPs) can exhibit high catalytic activity selectivity and stability for the dehydrogenation of chemical hydrogen storage materials which will clear the way for the commercial application of liquid chemical hydrogen storage technology. This review has summarized the recent important research progress in the MNP-catalyzed liquid chemical hydrogen storage technology including formic acid dehydrogenation hydrazine hydrate dehydrogenation and ammonia borane dehydrogenation discussed the urgent challenges in the key field and pointed out the future research trends.
Underground Hydrogen Storage: Application of Geochemical Modelling in a Case Study in the Molasse Basin, Upper Austria
Feb 2019
Publication
Hydrogen storage in depleted gas fields is a promising option for the large-scale storage of excess renewable energy. In the framework of the hydrogen storage assessment for the “Underground Sun Storage” project we conduct a multi-step geochemical modelling approach to study fluid–rock interactions by means of equilibrium and kinetic batch simulations. With the equilibrium approach we estimate the long-term consequences of hydrogen storage whereas kinetic models are used to investigate the interactions between hydrogen and the formation on the time scales of typical storage cycles. The kinetic approach suggests that reactions of hydrogen with minerals become only relevant over timescales much longer than the considered storage cycles. The final kinetic model considers both mineral reactions and hydrogen dissolution to be kinetically controlled. Interactions among hydrogen and aqueous-phase components seem to be dominant within the storage-relevant time span. Additionally sensitivity analyses of hydrogen dissolution kinetics which we consider to be the controlling parameter of the overall reaction system were performed. Reliable data on the kinetic rates of mineral dissolution and precipitation reactions specifically in the presence of hydrogen are scarce and often not representative of the studied conditions. These uncertainties in the kinetic rates for minerals such as pyrite and pyrrhotite were investigated and are discussed in the present work. The proposed geochemical workflow provides valuable insight into controlling mechanisms and risk evaluation of hydrogen storage projects and may serve as a guideline for future investigations.
Evaluating the Opportunity to Repurpose Gas Transmission Assets for Hydrogen Transportation
Sep 2021
Publication
The UK National Transmission System (NTS) is a key enabler to decarbonise the gas network in Great Britain (GB) in order to meet the UK government’s target of net-zero emissions by 2050. FutureGrid is National Grid’s research programme assessing the capability of the transmission system to transport hydrogen. Our goal is to accelerate the decarbonisation of power industry and heat by delivering a safe supply of energy to all customers both during and after the energy transition. FutureGrid will lead to a better understanding of what the technical parameters are around the ultimate role of the NTS in the energy system and how the transition can be managed. Under FutureGrid National Grid will construct a NTS hydrogen test facility at DNV’s Spadeadam testing and research site. NTS assets due to be decommissioned in early RIIO2 will be reconstructed to create a test network that can be used to answer some of the fundamental questions around safety and operation of a converted network. Flows of hydrogen/natural gas blends including 100% hydrogen will be tested for the first time in GB at transmission pressures. This system will connect to the existing H21 distribution network test facility at Spadeadam to prove a complete beach-to-meter network can be decarbonised to develop a comprehensive programme for the hydrogen transition. The project will provide a transmission facility which is a key enabler for more advanced hydrogen testing on industrial equipment such as hydrogen separation technology hydrogen compressors and/or purification of hydrogen for transport. Our paper will detail the current position and aims of the project.
Interfacial Fracture Strength Property of Micro-scale SiN/Cu Components
Jul 2016
Publication
The strength against fracture nucleation from an interface free-edge of silicon-nitride (SiN)/copper (Cu) micro-components is evaluated. A special technique that combines a nano-indenter specimen holder and an environmental transmission electron microscope (E-TEM) is employed. The critical load at the onset of fracture nucleation from a wedge-shaped free-edge (opening angle: 90°) is measured both in a vacuum and in a hydrogen (H2) environment and the critical stress distribution is evaluated by the finite element method (FEM). It is found that the fracture nucleation is dominated by the near-edge elastic singular stress field that extends about a few tens of nanometers from the edge. The fracture nucleation strength expressed in terms of the stress intensity factor (K) is found to be eminently reduced in a H2 environment.
Planning, Optimisation and Evaluation of Small Power-to-Gas-to-Power Systems: Case Study of a German Dairy
May 2022
Publication
In the course of the energy transition distributed hybrid energy systems such as the combination of photovoltaic (PV) and battery storages is increasingly being used for economic and ecological reasons. However renewable electricity generation is highly volatile and storage capacity is usually limited. Nowadays a new storage component is emerging: the power-to-gas-to-power (PtGtP) technology which is able to store electricity in the form of hydrogen even over longer periods of time. Although this technology is technically well understood and developed there are hardly any evaluations and feasibility studies of its widespread integration into current distributed energy systems under realistic legal and economic market conditions. In order to be able to give such an assessment we develop a methodology and model that optimises the sizing and operation of a PtGtP system as part of a hybrid energy system under current German market conditions. The evaluation is based on a multi-criteria approach optimising for both costs and CO2 emissions. For this purpose a brute-force-based optimal design approach is used to determine optimal system sizes combined with the energy system simulation tool oemof.solph. In order to gain further insights into this technology and its future prospects a sensitivity analysis is carried out. The methodology is used to examine the case study of a German dairy and shows that PtGtP is not yet profitable but promising.
Energy Management System for Hybrid PV/Wind/Battery/Fuel Cell in Microgrid-Based Hydrogen and Economical Hybrid Battery/Super Capacitor Energy Storage
Sep 2021
Publication
The present work addresses the modelling control and simulation of a microgrid integrated wind power system with Doubly Fed Induction Generator (DFIG) using a hybrid energy storage system. In order to improve the quality of the waveforms (voltages and currents) supplied to the grid instead of a two level-inverter the rotor of the DFIG is supplied using a three-level inverter. A new adaptive algorithm based on combined Direct Reactive Power Control (DRPC) and fuzzy logic controls techniques is applied to the proposed topology. In this work two topologies are proposed. In the first one the active power injected into the grid is smoothened by using an economical hybrid battery and supercapacitor energy storage system. However in the second one the excess wind energy is used to produce and store the hydrogen and then a solid oxide fuel cell system (SOFC) is utilized to regenerate electricity by using the stored hydrogen when there is not enough wind energy. To avoid overcharging deep discharging of batteries to mitigate fluctuations due to wind speed variations and to fulfil the requirement of the load profile a power management algorithm is implemented. This algorithm ensures smooth output power in the first topology and service continuity in the second. The modelling and simulation results are presented and analysed using Matlab/Simulin.
Performance Assessment of a Hybrid System with Hydrogen Storage and Fuel Cell for Cogeneration in Buildings
Jun 2020
Publication
The search for new fuels to supersede fossil fuels has been intensified these recent decades. Among these fuels hydrogen has attracted much interest due to its advantages mainly cleanliness and availability. It can be produced from various raw materials (e.g. water biomass) using many resources mainly water electrolysis and natural gas reforming. However water electrolysis combined with renewable energy sources is the cleanest way to produce hydrogen while reducing greenhouse gases. Besides hydrogen can be used by fuel cells for producing both electrical and thermal energy. The aim of this work was towards efficient integration of this system into energy efficient buildings. The system is comprised of a photovoltaic system hydrogen electrolyzer and proton exchange membrane fuel cell operating as a cogeneration system to provide the building with both electricity and thermal energy. The system’s modeling simulations and experimentations were first conducted over a short-run period to assess the system’s performance. Reported results show the models’ accuracy in analyzing the system’s performance. We then used the developed models for long-run testing of the hybrid system. Accordingly the system’s electrical efficiency was almost 32%. Its overall efficiency reached 64.5% when taking into account both produced electricity and thermal energy.
Thermodynamics and Kinetics of Hydriding and Dehydriding Reactions in Mg-based Hydrogen Storage Materials
Oct 2021
Publication
Mg-based materials are one of the most promising hydrogen storage candidates due to their high hydrogen storage capacity environmental benignity and high Clarke number characteristics. However the limited thermodynamics and kinetic properties pose major challenges for their engineering applications. Herein we review the recent progress in improving their thermodynamics and kinetics with an emphasis on the models and the influence of various parameters in the calculated models. Subsequently the impact of alloying composite and nano-crystallization on both thermodynamics and dynamics are discussed in detail. In particular the correlation between various modification strategies and the hydrogen capacity dehydrogenation enthalpy and temperature hydriding/dehydriding rates are summarized. In addition the mechanism of hydrogen storage processes of Mg-based materials is discussed from the aspect of classical kinetic theories and microscope hydrogen transferring behavior. This review concludes with an outlook on the remaining challenge issues and prospects.
Influence of Hydrogen Environment on Fatigue Fracture Morphology of X80 Pipeline Steel
Dec 2022
Publication
The rapid development of hydrogen energy requires the use of natural gas infrastructure for hydrogen transportation. It is very important to study hydrogen-added natural gas transportation technology which is a key way to rapidly develop coal-based gas and renewable energy. This study aims to study the influence of X80 pipeline steel's fatigue performance in hydrogen environment and perform fatigue tests on notched round rod specimens under different hydrogen concentration. The experimental results show that hydrogen seriously affects the fatigue life of pipeline steel. After reaching a certain hydrogen concentration as the hydrogen concentration continues to increase the fatigue life decreases gradually. Combined with SEM analysis of fracture morphology the decrease in the size and density of the dimples reduces the displacement amplitude while the increase in the planar area increases the displacement during fatigue fracture due to accelerated crack propagation. From this study we can know the influence of hydrogen concentration on the fracture morphology of pipeline steel which provides an understanding of the effect of hydrogen on fatigue fracture morphology and a broader safety analysis.
Analysis of Hydrogen in Inorganic Materials and Coatings: A Critical Review
Jun 2021
Publication
The currently used bulk analysis and depth profiling methods for hydrogen in inorganic materials and inorganic coatings are reviewed. Bulk analysis of hydrogen is based on fusion of macroscopic samples in an inert gas and the detection of the thereby released gaseous H2 using inert gas fusion (IGF) and thermal desorption spectroscopy (TDS). They offer excellent accuracy and sensitivity. Depth profiling methods involve glow discharge optical emission spectroscopy and mass spectrometry (GDOES and GDMS) laser-induced breakdown spectroscopy (LIBS) secondary ion mass spectrometry (SIMS) nuclear reaction analysis (NRA) and elastic recoil detection analysis (ERDA). The principles of all these methods are explained in terms of the methodology calibration procedures analytical performance and major application areas. The synergies and the complementarity of various methods of hydrogen analysis are described. The existing literature about these methods is critically evaluated and major papers concerning each method are listed.
No more items...