Applications & Pathways
Life-Cycle and Applicational Analysis of Hydrogen Production and Powered Inland Marine Vessels
Aug 2023
Publication
Green energy is at the forefront of current policy research and engineering but some of the potential fuels require either a lot of deeper research or a lot of infrastructure before they can be implemented. In the case of hydrogen both are true. This report aims to analyse the potential of hydrogen as a future fuel source by performing a life-cycle assessment. Through this the well-to-tank phase of fuel production and the usage phase of the system have been analysed. Models have also been created for traditional fuel systems to best compare results. The results show that hydrogen has great potential to convert marine transport to operating off green fuels when powered through low-carbon energy sources which could reduce a huge percentage of the international community’s greenhouse gas emissions. Hydrogen produced through wind powered alkaline electrolysis produced emission data 5.25 g of CO2 equivalent per MJ compared to the 210 g per MJ produced by a medium efficiency diesel equivalent system a result 40 times larger. However with current infrastructure in most countries not utilising a great amount of green energy production the effects of hydrogen usage could be more dangerous than current fuel sources owing to the incredible energy requirements of hydrogen production with even grid (UK) powered electrolysis producing an emission level of 284 g per MJ which is an increase against standard diesel systems. From this the research concludes that without global infrastructure change hydrogen will remain as a potential fuel rather than a common one.
Environmental Economical Dispatching of Electric–Gas Integrated Energy System Considering Hydrogen Compressed-Natural Gas
Dec 2022
Publication
As a high-quality secondary energy hydrogen energy has great potential in energy storage and utilization. The development of power-to-hydrogen (P2H) technology has alleviated the problem of wind curtailment and improved the coupling between the power grid and the natural gas grid. Under the premise of ensuring safety using P2H technology to mix the produced hydrogen into the natural gas network for long-distance transmission and power generation can not only promote the development of hydrogen energy but also reduce carbon emissions. This paper presents a new model for incorporating hydrogen into natural gas pipelines. To minimize the sum of wind curtailment cost operation cost and carbon emission cost an electric–gas integrated energy system (EGIES) model of hydrogen-compressed natural gas (HCNG) containing P2H for power generation is constructed. Aiming at the problem of global warming caused by a lot of abandoned wind and carbon emissions the economy and environmental protection of the system model are analyzed. The results show that the model of EGIES considering HCNG can not only absorb excess wind power but also reduce carbon emission costs and system costs which can reduce the total cost of the environmental economic dispatch of the EGIES by about 34.1%. In the context of the EGIES the proposal of this model is of great significance to the economical and environmentally friendly operation of the system.
Life Cycle Greenhouse Gas Emission Assessment for Using Alternative Marine Fuels: A Very Large Crude Carrier (VLCC) Case Study
Dec 2022
Publication
The International Maritime Organization (IMO) has set decarbonisation goals for the shipping industry. As a result shipowners and operators are preparing to use low- or zero-carbon alternative fuels. The greenhouse gas (GHG) emission performances are fundamental for choosing suitable marine fuels. However the current regulations adopt tank-to-wake (TTW) emission assessment methods that could misrepresent the total climate impacts of fuels. To better understand the well-to-wake (WTW) GHG emission performances this work applied the life cycle assessment (LCA) method to a very large crude carrier (VLCC) sailing between the Middle East and China to investigate the emissions. The life cycle GHG emission impacts of using alternative fuels including liquified natural gas (LNG) methanol and ammonia were evaluated and compared with using marine gas oil (MGO). The bunkering site of the VLCC was in Zhoushan port China. The MGO and LNG were imported from overseas while methanol and ammonia were produced in China. Four production pathways for methanol and three production pathways for ammonia were examined. The results showed that compared with MGO using fossil energy-based methanol and ammonia has no positive effect in terms of annual WTW GHG emissions. The emission reduction effects of fuels ranking from highest to lowest were full solar and battery-based methanol full solar and battery-based ammonia and LNG. Because marine ammonia-fuelled engines have not been commercialised laboratory data were used to evaluate the nitrous oxide (N2O) emissions. The GHG emission reduction potential of ammonia can be exploited more effectively if the N2O emitted from engines is captured and disposed of through after-treatment technologies. This paper discussed three scenarios of N2O emission abatement ratios of 30% 50% and 90%. The resulting emission reduction effects showed that using full solar and battery-based ammonia with 90% N2O abatement performs better than using full solar and battery-based methanol. The main innovation of this work is realising the LCA GHG emission assessment for a deep-sea ship.
Low-carbon Economic Operation of IES Based on Life Cycle Method and Hydrogen Energy Utilization
Aug 2023
Publication
The Integrated Energy System (IES) that coordinates multiple energy sources can effectively improve energy utilization and is of great significance to achieving energy conservation and emission reduction goals. In this context a low-carbon and economic dispatch model for IES is proposed. Firstly a hydrogen energy-based IES (H2-IES) is constructed to refine the utilization process of hydrogen energy. Secondly the carbon emissions of different energy chains throughout their life cycle are analyzed using the life cycle assessment method (LCA) and the carbon emissions of the entire energy supply and demand chain are considered. Finally a staged carbon trading mechanism is adopted to promote energy conservation and emission reduction. Based on this an IES low-carbon and economic dispatch model is constructed with the optimization goal of minimizing the sum of carbon trading costs energy procurement costs and hydrogen sales revenue while considering network constraints and constraints on key equipment. By analyzing the model under different scenarios the introduction of life cycle assessment staged carbon trading and hydrogen energy utilization is shown to promote low-carbon and economic development of the comprehensive energy system.
Hydrogen-electricity Hybrid Energy Pipelines for Railway Transportation: Design and Economic Evaluation
Mar 2024
Publication
With the decarbonization and electrification of modern railway transportation the demand for both the highcapacity electrical energy and hydrogen fuel energy is increasingly high. A novel scheme was proposed from liquid hydrogen production by surplus wind and solar energy to liquid hydrogen-electricity hybrid energy transmission for railway transportation. The 100 MW hybrid energy transmission pipeline was designed with the 10 kA/1.5 kV superconducting DC cable for electricity and cryogenic layers for liquid hydrogen and liquid nitrogen showing strong capability in transmitting “electricity + cold energy + chemical energy” simultaneously. Economic evaluation was performed with respect to the energy equipment capacity and costs with sensitivity and profitability analysis. With the discount rate 8% the dynamic payback period of the hybrid energy pipeline was 7.1 years. Results indicated that the shortest dynamic payback period of the hybrid energy pipeline was 4.8 years with the maximum transmission distance 93 km. Overall this article shows the novel concept and design of liquid hydrogen-electricity hybrid energy pipelines and proves the technical and economic feasibilities for future bulk hybrid energy transmission for railway transportation.
Industrial and Academic Collaboration Strategies on Hydrogen Fuel Cell Technology Development in Malaysia
Nov 2013
Publication
Hydrogen fuel cells are electrochemical power generators of high conversion efficiency and incredibly clean operation. Throughout the world the growth of fuel cell research and application has been very rapid in the last ten years where successful pilot projects on many areas have been implemented. In Malaysia approximately RM40 million has been granted to academic research institutions for fuel cell study and development. Recently Malaysia saw the emergence of its first hydrogen fuel cell developer signaling the readiness of the industrial sector to be involved in marketing the potential of fuel cells. Focusing mainly on Polymer Electrolyte Membrane fuel cell technology this paper demonstrates the efforts by Malaysian institutions both industrial and academic to promote hydrogen fuel cell education training application R&D as well as technology transfer. Emphasis is given to the existing collaboration between G-Energy Technologies and UniversitiTeknologi MARA that culminates with the successful application of a locally developed fuel cell system for a single-seated vehicle. Briefs on the potential of realizing a large-scale utilization of this clean technology into Malaysia’s mainstream power industry domestic consumers and energy consuming industries is also discussed. Key challenges are also identified where pilot projects government policy and infrastructural development is central to strengthen the prospect of hydrogen fuel cell implementation in Malaysia.
An Approach for Sizing a PV-battery-electrolyzer-fuel cell Energy System: A Cast Study at a Field Lab
May 2023
Publication
Hydrogen is becoming increasingly popular as a clean secure and affordable energy source for the future. This study develops an approach for designing a PV–battery–electrolyzer–fuel cell energy system that utilizes hydrogen as a long-term storage medium and battery as a short-term storage medium. The system is designed to supply load demand primarily through direct electricity generation in the summer and indirect electricity generation through hydrogen in the winter. The sizing of system components is based on the direct electricity and indirect hydrogen demand with a key input parameter being the load sizing factor which determines the extent to which hydrogen is used to meet seasonal imbalance. Technical and financial indicators are used to assess the performance of the designed system. Simulation results indicate that the energy system can effectively balance the seasonal variation of renewable generation and load demand with the use of hydrogen. Additionally guidelines for achieving self-sufficiency and system sustainability for providing enough power in the following years are provided to determine the appropriate component size. The sensitivity analysis indicates that the energy system can achieve self-sufficiency and system sustainability with a proper load sizing factor from a technical perspective. From an economic perspective the levelized cost of energy is relatively high because of the high costs of hydrogen-related components at this moment. However it has great economic potential for future self-sufficient energy systems with the maturity of hydrogen technologies.
Fuel-Cell Electric Vehicles: Plotting a Scientific and Technological Knowledge Map
Mar 2020
Publication
The fuel-cell electric vehicle (FCEV) has been defined as a promising way to avoid road transport greenhouse emissions but nowadays they are not commercially available. However few studies have attempted to monitor the global scientific research and technological profile of FCEVs. For this reason scientific research and technological development in the field of FCEV from 1999 to 2019 have been researched using bibliometric and patent data analysis including network analysis. Based on reports the current status indicates that FCEV research topics have reached maturity. In addition the analysis reveals other important findings: (1) The USA is the most productive in science and patent jurisdiction; (2) both Chinese universities and their authors are the most productive in science; however technological development is led by Japanese car manufacturers; (3) in scientific research collaboration is located within the tri-polar world (North America–Europe–Asia-Pacific); nonetheless technological development is isolated to collaborations between companies of the same automotive group; (4) science is currently directing its efforts towards hydrogen production and storage energy management systems related to battery and hydrogen energy Life Cycle Assessment and greenhouse gas (GHG) emissions. The technological development focuses on technologies related to electrically propelled vehicles; (5) the International Journal of Hydrogen Energy and SAE Technical Papers are the two most important sources of knowledge diffusion. This study concludes by outlining the knowledge map and directions for further research.
How to Make Climate-neutral Aviation Fly
Jul 2023
Publication
The European aviation sector must substantially reduce climate impacts to reach net-zero goals. This reduction however must not be limited to flight CO2 emissions since such a narrow focus leaves up to 80% of climate impacts unaccounted for. Based on rigorous life-cycle assessment and a time-dependent quantification of non-CO2 climate impacts here we show that from a technological standpoint using electricity-based synthetic jet fuels and compensating climate impacts via direct air carbon capture and storage (DACCS) can enable climate-neutral aviation. However with a continuous increase in air traffic synthetic jet fuel produced with electricity from renewables would exert excessive pressure on economic and natural resources. Alternatively compensating climate impacts of fossil jet fuel via DACCS would require massive CO2 storage volumes and prolong dependence on fossil fuels. Here we demonstrate that a European climate-neutral aviation will fly if air traffic is reduced to limit the scale of the climate impacts to mitigate.
Predicting Power and Hydrogen Generation of a Renewable Energy Converter Utilizing Data-Driven Methods: A Sustainable Smart Grid Case Study
Jan 2023
Publication
This study proposes a data-driven methodology for modeling power and hydrogen generation of a sustainable energy converter. The wave and hydrogen production at different wave heights and wind speeds are predicted. Furthermore this research emphasizes and encourages the possibility of extracting hydrogen from ocean waves. By using the extracted data from the FLOW-3D software simulation and the experimental data from the special test in the ocean the comparison analysis of two data-driven learning methods is conducted. The results show that the amount of hydrogen production is proportional to the amount of generated electrical power. The reliability of the proposed renewable energy converter is further discussed as a sustainable smart grid application.
Conditions for Profitable Operation of P2X Energy Hubs to Meet Local Demand Under Energy Market Access
Feb 2023
Publication
This paper analyzes the operation of an energy hub on a community level with an integrated P2X facility and with access to energy markets. In our case P2X allows converting power to hydrogen heat methane or back to power. We consider the energy hub as a large prosumer who can be both a producer and consumer in the markets with the novelty that P2X technology is available. We investigate how such a P2X energy hub trades optimally in the electricity market and satisfies local energy demand under the assumption of a long-term strong climate scenario in year 2050. For numerical analysis a case study of a mountain village in Switzerland is used. One of the main contributions of this paper is to quantify key conditions for profitable operations of such a P2X energy hub. In particular the analysis includes impacts of influencing factors on profits and operational patterns in terms of different degrees of self-sufficiency and different availability of local renewable resources. Moreover the access to real-time wholesale market electricity price signals and a future retail hydrogen market is assessed. The key factors for the successful operation of a P2X energy hub are identified to be sufficient local renewable resources and access to a retail market of hydrogen. The results also show that the P2X operation leads to an increased deployment of local renewables especially in the case of low initial deployment; on the other hand seasonal storage plays a subordinated role. Additionally P2X lowers for the community the wholesale electricity market trading volumes.
Ammonia as a Suitable for Fuel Cells
Aug 2014
Publication
Ammonia an important basic chemical is produced at a scale of 150 million tons per year. Half of hydrogen produced in chemical industry is used for ammonia production. Ammonia containing 17.5 wt% hydrogen is an ideal carbon-free fuel for fuel cells. Compared to hydrogen ammonia has many advantages. In this mini-review the suitability of ammonia as fuel for fuel cells the development of different types of fuel cells using ammonia as the fuel and the potential applications of ammonia fuel cells are briefly reviewed.
Impact of Fuel Production Technologies on Energy Consumption and GHG Emissions from Diesel and Electric–Hydrogen Hybrid Buses in Rio de Janeiro, Brazil
Apr 2023
Publication
In view of the GHG reduction targets to be met Brazilian researchers are looking for cleaner alternatives to energy sources. These alternatives are primarily to be applied in the transport sector which presents high energy consumption as well as high CO2 emissions. In this sense this research developed an LCI study considering two bus alternatives for the city of Rio de Janeiro: diesel-powered internal combustion buses (ICEB) and a hydrogen-powered polymer fuel cell hybrid bus (FCHB). For the FCHB three hydrogen production methods were also included: water electrolysis (WE) ethanol steam reforming (ESR) and natural gas steam reforming (NGSR). The research was aimed at estimating energy consumption including the percentage of energy that is renewable as well as CO2 emissions. The results show diesel as the energy source with the highest emissions as well as the highest fossil energy consumption. Regarding the alternatives for hydrogen production water electrolysis stood out with the lowest emissions.
A Multi-energy Multi-microgrid System Planning Model for Decarbonisation and Decontamination of Isolated Systems
May 2023
Publication
Decarbonising and decontaminating remote regions in the world presents several challenges. Many of these regions feature isolation dispersed demand in large areas and a lack of economic resources that impede the development of robust and sustainable networks. Furthermore isolated systems in the developing world are mostly based on diesel generation for electricity and firewood and liquefied petroleum gas for heating as these options do not require a significant infrastructure cost. In this context we present a stochastic multi-energy multi-microgrid system planning model that integrates electricity heat and hydrogen networks in isolated systems. The model is stochastic to capture uncertainty in renewable generation outputs particularly hydro and wind and thus design a multi-energy system proved secured against such uncertainty. The model also features two distinct constraints to limit the emissions of CO2 (for decarbonisation) and particulate matter (for decontamination) and incorporates firewood as a heating source. Moreover given that the focus is on low-voltage networks we introduce a fully linear AC power flow equations set allowing the planning model to remain tractable. The model is applied to a real-world case study to design a multi-energy multi-microgrid system in an isolated region in Chilean Patagonia. In a case with a zero limit over direct CO2 emissions the total system’s cost increases by 34% with respect to an unconstrained case. In a case with a zero limit over particulate matter emissions the total system’s cost increases by 189%. Finally although an absolute zero limit over both particulate matter and direct CO2 emissions leads to a total system’s cost increase of 650% important benefits in terms of decarbonisation and decontamination can be achieved at marginal cost increments.
An Optimization-Based Model for A Hybrid Photovoltaic-Hydrogen Storage System for Agricultural Operations in Saudi Arabia
Apr 2023
Publication
Renewable energy technologies and resources particularly solar photovoltaic systems provide cost-effective and environmentally friendly solutions for meeting the demand for electricity. The design of such systems is a critical task as it has a significant impact on the overall cost of the system. In this paper a mixed-integer linear programming-based model is proposed for designing an integrated photovoltaic-hydrogen renewable energy system to minimize total life costs for one of Saudi Arabia’s most important fields a greenhouse farm. The aim of the proposed system is to determine the number of photovoltaic (PV) modules the amount of hydrogen accumulated over time and the number of hydrogen tanks. In addition binary decision variables are used to describe either-or decisions on hydrogen tank charging and discharging. To solve the developed model an exact approach embedded in the general algebraic modeling System (GAMS) software was utilized. The model was validated using a farm consisting of 20 greenhouses a worker-housing area and a water desalination station with hourly energy demand. The findings revealed that 1094 PV panels and 1554 hydrogen storage tanks are required to meet the farm’s load demand. In addition the results indicated that the annual energy cost is $228234 with a levelized cost of energy (LCOE) of 0.12 $/kWh. On the other hand the proposed model reduced the carbon dioxide emissions to 882 tons per year. These findings demonstrated the viability of integrating an electrolyzer fuel cell and hydrogen tank storage with a renewable energy system; nevertheless the cost of energy produced remains high due to the high capital cost. Moreover the findings indicated that hydrogen technology can be used as an energy storage solution when the production of renewable energy systems is variable as well as in other applications such as the industrial residential and transportation sectors. Furthermore the results revealed the feasibility of employing renewable energy as a source of energy for agricultural operations.
Multi-Objective Optimization for Solar-Hydrogen-Battery-Integrated Electric Vehicle Charging Stations with Energy Exchange
Oct 2023
Publication
The importance of electric vehicle charging stations (EVCS) is increasing as electric vehicles (EV) become more widely used. EVCS with multiple low-carbon energy sources can promote sustainable energy development. This paper presents an optimization methodology for direct energy exchange between multi-geographic dispersed EVCSs in London UK. The charging stations (CSs) incorporate solar panels hydrogen battery energy storage systems and grids to support their operations. EVs are used to allow the energy exchange of charging stations. The objective function of the solar-hydrogen-battery storage electric vehicle charging station (SHS-EVCS) includes the minimization of both capital and operation and maintenance (O&M) costs as well as the reduction in greenhouse gas emissions. The system constraints encompass the power output limits of individual components and the need to maintain a power balance between the SHS-EVCSs and the EV charging demand. To evaluate and compare the proposed SHS-EVCSs two multi-objective optimization algorithms namely the Non-dominated Sorting Genetic Algorithm (NSGA-II) and the Multi-objective Evolutionary Algorithm Based on Decomposition (MOEA/D) are employed. The findings indicate that NSGA-II outperforms MOEA/D in terms of achieving higher-quality solutions. During the optimization process various factors are considered including the sizing of solar panels and hydrogen storage tanks the capacity of electric vehicle chargers and the volume of energy exchanged between the two stations. The application of the optimized SHS-EVCSs results in substantial cost savings thereby emphasizing the practical benefits of the proposed approach.
An Economic and Greenhouse Gas Footprint Assessment of International Maritime Transportation of Hydrogen Using Liquid Organic Hydrogen Carriers
Apr 2023
Publication
The supply storage and (international) transport of green hydrogen (H2) are essential for the decarbonization of the energy sector. The goal of this study was to assess the final cost-price and carbon footprint of imported green H2 in the market via maritime shipping of liquid organic hydrogen carriers (LOHCs) including dibenzyl toluene-perhydro-dibenzyltoluene (DBTPDBT) and toluene-methylcyclohexane (TOL-MCH) systems. The study focused on logistic steps in intra-European supply chains in different scenarios of future production in Portugal and demand in the Netherlands and carbon tariffs between 2030 and 2050. The case study is based on a formally accepted agreement between Portugal and the Netherlands within the Strategic Forum on Important Projects of Common European Interest (IPCEI). Under the following assumptions the results show that LOHCs are a viable technical-economic solution with logistics costs from 2030 to 2050 varying between 0.30-0.37 €/kg-H2 for DBT-PDBT and 0.28-0.34 €/kg-H2 for TOL-MCH. The associated CO2 emissions of these international H2 supply chains are between 0.46 and 2.46 kg-CO2/GJ (LHV) and 0.55-2.95 kg-CO2/GJ (LHV) for DBT-PDBT and TOL-MCH respectively.
Sustainable Hydrogen Energy in Aviation - A Narrative Review
Feb 2023
Publication
In the modern world zero-carbon society has become a new buzzword of the era. Many projects have been initiated to develop alternatives not only to the environmental crisis but also to the shortage of fossil fuels. With successful projects in automobile technology hydrogen fuel is now being tested and utilized as a sustainable green fuel in the aviation sector which will lead to zero carbon emission in the future. From the mid-20th century to the early 21st numerous countries and companies have funded multimillion projects to develop hydrogen-fueled aircraft. Empirical data show positive results for various projects. Consequently large companies are investing in various innovations undertaken by researchers under their supervision. Over time the efficiency of hydrogen-fueled aircraft has improved but the lack of refueling stations large production cost and consolidated carbon market share have impeded the path of hydrogen fuel being commercialized. In addition the Unmanned Aerial Vehicle (UAV) is another important element of the Aviation industry Hydrogen started to be commonly used as an alternative fuel for heavy-duty drones using fuel cell technology. The purpose of this paper is to provide an overview of the chronological development of hydrogen-powered aircraft technology and potential aviation applications for hydrogen and fuel cell technology. Furthermore the major barriers to widespread adoption of hydrogen technology in aviation are identified as are future research opportunities.
Research on Energy Management Method of Fuel Cell/Supercapacitor Hybrid Trams Based on Optimal Hydrogen Consumption
Jul 2023
Publication
In this paper based on the operating states and characteristics of fuel cell/supercapacitor hybrid trams an optimal hydrogen energy management method is proposed. This method divides the operating states into two parts: traction state and non-traction state. In the traction state the real-time loss function of the hybrid power system which is used to obtain the fuel cell optimal output power under the different demand powers and supercapacitor voltage is established. In the non-traction state the constant-power charging method which is obtained by solving the power-voltage charging model is used to ensure the supercapacitor voltage of the beginning-state and the end-state in an entire operation cycle are the same. The RT-LAB simulation platform is used to verify that the proposed method has the ability to control the hybrid real-time system. Using the comparative experiment between the proposed method and power-follow method the results show that the proposed method offers a significant improvement in both fuel cell output stability and hydrogen consumption in a full operation cycle.
A Comparative Study of Energy Consumption and Recovery of Autonomous Fuel-Cell Hydrogen–Electric Vehicles Using Different Powertrains Based on Regenerative Braking and Electronic Stability Control System
Mar 2021
Publication
Today with the increasing transition to electric vehicles (EVs) the design of highly energy-efficient vehicle architectures has taken precedence for many car manufacturers. To this end the energy consumption and recovery rates of different powertrain vehicle architectures need to be investigated comprehensively. In this study six different powertrain architectures—four independent in-wheel motors with regenerative electronic stability control (RESC) and without an RESC one-stage gear (1G) transmission two-stage gear (2G) transmission continuously variable transmission (CVT) and downsized electric motor with CVT—were mathematically modeled and analyzed under real road conditions using nonlinear models of an autonomous hydrogen fuel-cell electric vehicle (HFCEV). The aims of this paper were twofold: first to compare the energy consumption performance of powertrain architectures by analyzing the effects of the regenerative electronic stability control (RESC) system and secondly to investigate the usability of a downsized electrical motor for an HFCEV. For this purpose all the numerical simulations were conducted for the well-known FTP75 and NEDC urban drive cycles. The obtained results demonstrate that the minimum energy consumption can be achieved by a 2G-based powertrain using the same motor; however when an RESC system is used the energy recovery/consumption rate can be increased. Moreover the results of the article show that it is possible to use a downsized electric motor due to the CVT and this powertrain significantly reduces the energy consumption of the HFCEV as compared to all the other systems. The results of this paper present highly significant implications for automotive manufacturers for designing and developing a cleaner electrical vehicle energy consumption and recovery system.
Life Cycle Assessment of Waste-to-hydrogen Systems for Fuel Cell Electric Buses in Glasgow, Scotland
Jun 2022
Publication
Waste-to-hydrogen (WtH) technologies are proposed as a dual-purpose method for simultaneous non-fossil-fuel based hydrogen production and sustainable waste management. This work applied the life cycle assessment approach to evaluate the carbon saving potential of two main WtH technologies (gasification and fermentation) in comparison to the conventional hydrogen production method of steam methane reforming (SMR) powering fuel cell electric buses in Glasgow. It was shown that WtH technologies could reduce CO2-eq emissions per kg H2 by 50–69% as compared to SMR. Gasification treating municipal solid waste and waste wood had global warming potentials of 4.99 and 4.11 kg CO2-eq/kg H2 respectively which were lower than dark fermentation treating wet waste at 6.6 kg CO2-eq/kg H2 and combined dark and photo fermentation at 6.4 kg CO2-eq/kg H2. The distance emissions of WtH-based fuel cell electric bus scenarios were 0.33–0.44 kg CO2-eq/km as compared to 0.89 kg CO2-eq/km for the SMR-based scenario.
Strategies for Hydrogen-Enriched Methane Flameless Combustion in a Quasi-Industrial Furnace
Jan 2020
Publication
In this present work simulations of 20 kW furnace were carried out with hydrogenenriched methane mixtures to identify optimal geometrical configurations and operating conditions to operate in flameless combustion regime. The objective of this work is to show the advantages of flameless combustion for hydrogen-enriched fuels and the limits of current typical industrial designs for these mixtures. The performances of a semi-industrial combustion chamber equipped with a self-recuperative flameless burner are evaluated with increasing H2 concentrations. For highly H2-enriched mixtures typical burners employed for methane appear to be inadequate to reach flameless conditions. In particular for a typical coaxial injector configuration an equimolar mixture of hydrogen and methane represents the limit for hydrogen enrichment. To achieve flameless conditions different injector geometries and configuration were tested. Fuel dilution with CO2 and H2O was also investigated. Dilution slows the mixing process consequently helping the transition to flameless conditions. CO2 and H2O are typical products of hydrogen generation processes therefore their use in fuel dilution is convenient for industrial applications. Dilution thus allows the use of greater hydrogen percentages in the mixture.
Investigation of Different Load Characteristics, Component Dimensioning, and System Scaling for the Optimized Design of a Hybrid Hydrogen-Based PV Energy System
Jul 2023
Publication
The realization of a carbon-neutral civilization which has been set as a goal for the coming decades goes directly hand-in-hand with the need for an energy system based on renewable energies (REs). Due to the strong weather-related daily and seasonal fluctuations in supply of REs suitable energy storage devices must be included for such energy systems. For this purpose an energy system model featuring hybrid energy storage consisting of a hydrogen unit (for long-term storage) and a lithium-ion storage device (for short-term storage) was developed. With a proper design such a system can ensure a year-round energy supply by using electricity generated by photovoltaics (PVs). In the energy system that was investigated hydrogen (H2) was produced by using an electrolyser (ELY) with a PV surplus during the summer months and then stored in an H2 tank. During the winter due to the lack of PV power the H2 is converted back into electricity and heat by a fuel cell (FC). While the components of such a system are expensive a resource- and cost-efficient layout is important. For this purpose a Matlab/Simulink model that enabled an energy balance analysis and a component lifetime forecast was developed. With this model the results of extensive parameter studies allowed an optimized system layout to be created for specific applications. The parameter studies covered different focal points. Several ELY and FC layouts different load characteristics different system scales different weather conditions and different load levels—especially in winter with variations in heating demand—were investigated.
A Comparison of Well-to-Wheels Energy Use and Emissions of Hydrogen Fuel Cell, Electric, LNG, and Diesel-Powered Logistics Vehicles in China
Jul 2023
Publication
Global energy and environmental issues are becoming increasingly serious and the promotion of clean energy and green transportation has become a common goal for all countries. In the logistics industry traditional fuels such as diesel and natural gas can no longer meet the requirements of energy and climate change. Hydrogen fuel cell logistics vehicles are expected to become the mainstream vehicles for future logistics because of their “zero carbon” advantages. The GREET model is computer simulation software developed by the Argonne National Laboratory in the USA. It is extensively utilized in research pertaining to the energy and environmental impact of vehicles. This research study examines four types of logistics vehicles: hydrogen fuel cell vehicles (FCVs) electric vehicles LNG-fueled vehicles and diesel-fueled vehicles. Diesel-fueled logistics vehicles are currently the most abundant type of vehicle in the logistics sector. LNG-fueled logistics vehicles are considered as a short-term alternative to diesel logistics vehicles while electric logistics vehicles are among the most popular types of new-energy vehicles currently. We analyze and compare their well-to-wheels (WTW) energy consumption and emissions with the help of GREET software and conduct lifecycle assessments (LCAs) of the four types of vehicles to analyze their energy and environmental benefits. When comparing the energy consumption of the four vehicle types electric logistics vehicles (EVs) have the lowest energy consumption with slightly lower energy consumption than FCVs. When comparing the nine airborne pollutant emissions of the four vehicle types the emissions of the FCVs are significantly lower than those of spark-ignition internal combustion engine logistics vehicles (SI ICEVs) compression-ignition direct-injection internal combustion engine logistics vehicles (CIDI ICEVs) and EVs. This study fills a research gap regarding the energy consumption and environmental impact of logistics vehicles in China.
Pre-cooling Systems for Hydrogen Fueling Stations: Techno-economic Analysis for Scaled Enactment
Mar 2023
Publication
Hydrogen fueling standards stipulates a sustainable cooling system technically and economically. Accordingly the interior surface temperature of the on-board H2 storage tank in fuel cell electric vehicles must not exceed the maximum specified limit (358.15 K) and the fueling rate must be ≤ 42.86 sec / kg-H2 with T40 dispenser at 70 MPa. In this context H2 refueling stations often employ double-tube and block heat exchangers for heat transfer. This study examines the H2 pre-cooling system for various loads and provides a comparative techno-economic analysis of double tube heat exchangers (DTHE) and microchannel heat exchangers (MCHE) under stipulated technical operational and outlet gas standards. For this purpose thermal and hydraulic performances were simulated using ANSYS-CFX. Technical and cost models utilize manufacturer specifications and literature-based technical and economic characteristics to derive the minimum sustainable price defined as the price to sustain the product. The results showed that the MCHE outperformed the DTHE for setups in mass manufacturing improved effective heat transfer area and predicted long term unit cost. The annual quantitative output affects manufacturing expenses and profit margins substantially. With high production rates it is expected that the unit cost of the MCHE will decrease by up to 74%. In switching from DTHE to MCHE general material requirements decreased by ~60% with scrap waste savings of ~45% reflecting an appreciable footprint reduction.
Coordinated Planning and Operation of Inter Seasonal Heat Storage and P2G Devices Integrated to Urban Multi-energy System
Mar 2023
Publication
With the urbanization construction and the advancement of the carbon peaking and carbon neutrality goals urban energy systems are characterized by coupling multi-energy networks and a high proportion of renewable energy. Urban energy systems need to improve the quality of energy use as well as to achieve energy conservation and emission reduction. Inter-seasonal heat technology has satisfactory engineering application prospects in promoting renewable energy consumption and the energy supply of urban multi-energy systems. Considering inter-seasonal heat storage and electric hydrogen production a joint optimization method of planning and operation is proposed for the urban multi-energy flow system. First the operation framework of inter-seasonal heat storage and electric hydrogen production system is established which clarifies the energy flow of the urban multi-energy system. Secondly aiming at the goals of minimizing the equipment’s annual investment cost and the multi-energy system annual operation cost combined with the time series period division method a planning operation model has been established considering multi-objectives. Through case study it is shown that the proposed model can promote the renewable energy consumption and reduce the operation cost of the whole system.
Performance Analysis of Hybrid Solar/H2/Battery Renewable Energy System for Residential Electrification
Mar 2019
Publication
Due to the privileged location of Ecuador in terms of solar radiation the analysis and use of renewable energy system (RES) using solar energy has been of great interest during the last years. At the same time the supply support of RES in terms of direct current (DC) can be faced by using fuel cell (FC) systems which can give to the systems fully autonomy from fossil fuels. The aim of this paper is to propose the design of a hybrid photovoltaic-fuel cell-battery (PV-FC-B) system to supply the required electrical energy for residential use in the city of Guayaquil. The feasibility analysis constitutive elements of the system and adjusted variables are computed and presented using a computational tool. The results evidence that this system is not economically viable since the cost of energy (COE) in Ecuador is low compared to the COE of the proposed system. However a more detailed analysis considering the inherent benefits of no emission of pollutant gases is required to have a complete outlook.
Carbon Capture and Biomass in Industry: A Techno-economic Analysis and Comparison of Negative Emission Options
Apr 2021
Publication
Meeting the Paris Agreement will most likely require the combination of CO2 capture and biomass in the industrial sector resulting in net negative emissions. CO2 capture within the industry has been extensively investigated. However biomass options have been poorly explored with literature alluding to technical and economic barriers. In addition a lack of consistency among studies makes comparing the performance of CO2 capture and/or biomass use between studies and sectors difficult. These inconsistencies include differences in methodology system boundaries level of integration costs greenhouse gas intensity of feedstock and energy carriers and capital cost estimations. Therefore an integrated evaluation of the techno-economic performance regarding CO2 capture and biomass use was performed for five energy-intensive industrial sub-sectors. Harmonization results indicate that CO2 mitigation potentials vary for each sub-sector resulting in reductions of 1.4–2.7 t CO2/t steel (77%–149%) 0.7 t CO2/t cement (92%) 0.2 t CO2/t crude oil (68%) 1.9 t CO2/t pulp (1663%–2548%) and 34.9 t CO2/t H2 (313%). Negative emissions can be reached in the steel paper and H2 sectors. Novel bio-based production routes might enable net negative emissions in the cement and (petro) chemical sectors as well. All the above-mentioned potentials can be reached for 100 €/t CO2 or less. Implementing mitigation options could reduce industrial CO2 emissions by 10 Gt CO2/y by 2050 easily meeting the targets of the 2 ◦C scenario by the International Energy Agency (1.8 Gt CO2/y reduction) for the industrial sector and even the Beyond 2 ◦C scenario (4.2 Gt CO2/y reduction).
Simulating Offshore Hydrogen Production via PEM Electrolysis using Real Power Production Data from a 2.3 MW Floating Offshore Wind Turbine
Mar 2023
Publication
This work presents simulation results from a system where offshore wind power is used to produce hydrogen via electrolysis. Real-world data from a 2.3 MW floating offshore wind turbine and electricity price data from Nord Pool were used as input to a novel electrolyzer model. Data from five 31-day periods were combined with six system designs and hydrogen production system efficiency and production cost were estimated. A comparison of the overall system performance shows that the hydrogen production and cost can vary by up to a factor of three between the cases. This illustrates the uncertainty related to the hydrogen production and profitability of these systems. The highest hydrogen production achieved in a 31-day period was 17 242 kg using a 1.852 MW electrolyzer (i.e. utilization factor of approximately 68%) the lowest hydrogen production cost was 4.53 $/kg H2 and the system efficiency was in the range 56.1e56.9% in all cases.
A Novel Scheme to Allocate the Green Energy Transportation Costs—Application to Carbon Captured and Hydrogen
Mar 2023
Publication
Carbon dioxide (CO2 ) and hydrogen (H2 ) are essential energy vectors in the green energy transition. H2 is a fuel produced by electrolysis and is applied in heavy transportation where electrification is not feasible yet. The pollutant substance CO2 is starting to be captured and stored in different European locations. In Denmark the energy vision aims to use this CO2 to be reacted with H2 producing green methanol. Typically the production units are not co-located with consumers and thus the required transportation infrastructure is essential for meeting supply and demand. This work presents a novel scheme to allocate the transportation costs of CO2 and H2 in pipeline networks which can be applied to any network topology and with any allocation method. During the tariff formation process coordinated adjustments are made by the novel scheme on the original tariffs produced by the allocation method employed considering the location of each customer connected to pipeline network. Locational tariffs are provided as result and the total revenue recovery is guaranteed to the network owner. Considering active customers the novel scheme will lead to a decrease of distant pipeline flows thereby contributing to the prevention of bottlenecks in the transportation network. Thus structural reinforcements can be avoided reducing the total transportation cost paid by all customers in the long-term.
Renewable Methanol Production from Green Hydrogen and Captured CO2: A Techno-economic Assessment
Nov 2022
Publication
This paper aims to present a pre-feasibility study of a power-to-fuel plant configuration designed for the production of 500 kg/h of renewable methanol (e-methanol) from green hydrogen and captured carbon dioxide. Hydrogen is obtained by water electrolysis employing the overproduction of renewable electricity. Carbon dioxide is assumed to be separated from the flue gas of a conventional power station by means of an amine-based CO2 absorption system. A comprehensive process model has been developed with the support of Aspen Plus tool to simulate all the plant sections and the overall system. After the process optimization a detailed economic analysis – based on capital and operating costs derived from commercial-scale experience and assuming a 20- year lifetime – has been performed to calculate a levelized cost of methanol (LCoM) of 960 €/t (about 175 €/MWh). The analysis confirms that today the technology is still not competitive from the economic point of view being LCoM more than double than the current methanol price in the international market (450 €/t). However it indicates that the process is expected to become competitive in a mid-term future as a consequence of the new European policies. The study also reveals that LCoM is mainly affected by the electricity price and the electrolyser capital cost as well as the capacity factor of the plant.
Techno-economic Feasibility of Hybrid PV/wind/battery/thermal Storage Trigeneration System: Toward 100% Energy Independency and Green Hydrogen Production
Dec 2022
Publication
With the clear adverse impacts of fossil fuel-based energy systems on the climate and environment ever-growing interest and rapid developments are taking place toward full or nearly full dependence on renewable energies in the next few decades. Estonia is a European country with large demands for electricity and thermal energy for district heating. Considering it as the case study this work explores the feasibility and full potential of optimally sized photovoltaic (PV) wind and PV/wind systems equipped with electric and thermal storage to fulfill those demands. Given the large excess energy from 100% renewable energy systems for an entire country this excess is utilized to first meet the district heating demand and then to produce hydrogen fuel. Using simplified models for PV and wind systems and considering polymer electrolyte membrane (PEM) electrolysis a genetic optimizer is employed for scanning Estonia for optimal installation sites of the three systems that maximize the fulfillment of the demand and the supply–demand matching while minimizing the cost of energy. The results demonstrate the feasibility of all systems fully covering the two demands while making a profit compared to selling the excess produced electricity directly. However the PV-driven system showed enormous required system capacity and amounts of excess energy with the limited solar resources in Estonia. The wind system showed relatively closer characteristics to the hybrid system but required a higher storage capacity by 75.77%. The hybrid PV/wind-driven system required a total capacity of 194 GW most of which belong to the wind system. It was also superior concerning the amount (15.05 × 109 tons) and cost (1.42 USD/kg) of the produced green hydrogen. With such full mapping of the installation capacities and techno-economic parameters of the three systems across the country this study can assist policymakers when planning different country-scale cogeneration systems.
Optimal Allocation of Energy Sources in Hydrogen Production for Sustainable Deployment of Electric Vehicles
Jan 2023
Publication
We analyze the use of hydrogen as a fuel for the automotive industry with the aim of decarbonizing the economy. Hydrogen is a suitable option for avoiding pollutant gas emissions developing environmentally friendly technologies replacing fossil fuels with clean renewable energies and complying with the Paris Agreement and Glasgow resolutions. In this sense renewable energies such as wind solar photovoltaic geothermal biomass etc. can be used to produce the necessary hydrogen to power vehicles. In this way the entire process from hydrogen production to its consumption as fuel will be 100% clean. If we are to meet future energy demands it is necessary to forecast the amount of hydrogen needed taking into account the facilities currently available and new ones that will be required for its generation storage and distribution. This paper presents a process for optimizing hydrogen production for the automotive industry that considers the amount of hydrogen needed the type of facilities from which it will be produced how the different sources of production are to be combined to achieve a competitive product and the potential environmental impacts of each energy source. It can serve as a frame of reference for the various actors in the hydropower and automotive industries so that more efficient designs can be planned for the gradual introduction of hydrogen fuel cell vehicles (HFCVs). The methodology implemented in this paper sets an optimization problem for minimizing energy production costs and reducing environmental impacts according to the source of energy production. The EU framework with respect to the decarbonization of the economy the percentages of the different types of energy sources used and the non-polluting vehicle fleet in the automotive sector will be considered.
P2H Modeling and Operation in the Microgrid Under Coupled Electricity–Hydrogen Markets
Dec 2021
Publication
The uncertainty and volatility of wind power have led to large-scale wind curtailment during grid connections. The adoption of power-to-hydrogen (P2H) system in a microgrid (MG) can mitigate the renewable curtailment by hydrogen conversion and storage. This paper conducts unified modeling for different types of P2H systems and considers the multi-energy trading in a hydrogen-coupled power market. The proposed bi-level equilibrium model is beneficial to minimize the energy cost of microgrids. Firstly a microgrid operation model applied to different P2H systems including an alkaline electrolysis cell (AEC) a proton exchange membrane electrolysis cell (PEMEC) or a solid oxide electrolysis cell (SOEC) is proposed at the upper level. Secondly an electricity market–clearing model and a hydrogen market model are constructed at the lower level. Then the diagonalization algorithm is adopted to solve the multi-market equilibrium problem. Finally case studies based on an IEEE 14-bus system are conducted to validate the proposed model and the results show that the microgrid with a P2H system could gain more profits and help increase the renewable penetration.
Society, Materials, and the Environment: The Case of Steel
Mar 2020
Publication
This paper reviews the relationship between the production of steel and the environment as it stands today. It deals with raw material issues (availability scarcity) energy resources and generation of by-products i.e. the circular economy the anthropogenic iron mine and the energy transition. The paper also deals with emissions to air (dust Particulate Matter heavy metals Persistant Organics Pollutants) water and soil i.e. with toxicity ecotoxicity epidemiology and health issues but also greenhouse gas emissions i.e. climate change. The loss of biodiversity is also mentioned. All these topics are analyzed with historical hindsight and the present understanding of their physics and chemistry is discussed stressing areas where knowledge is still lacking. In the face of all these issues technological solutions were sought to alleviate their effects: many areas are presently satisfactorily handled (the circular economy—a historical’ practice in the case of steel energy conservation air/water/soil emissions) and in line with present environmental regulations; on the other hand there are important hanging issues such as the generation of mine tailings (and tailings dam failures) the emissions of greenhouse gases (the steel industry plans to become carbon-neutral by 2050 at least in the EU) and the emission of fine PM which WHO correlates with premature deaths. Moreover present regulatory levels of emissions will necessarily become much stricter.
Study on the Dynamic Optimal Control Strategy of an Electric-Hydrogen Hybrid Energy Storage System for a Direct Drive Wave Power Generation System
Jul 2023
Publication
A direct drive wave power generation system (DDWPGS) has the advantages of a simple structure and easy deployment and is the first choice to provide electricity for islands and operation platforms in the deep sea. However due to the off-grid the source and load cannot be matched so accommodation is an important issue. Hydrogen storage is the optimal choice for offshore wave energy accommodation. Therefore aiming at the source-load mismatch problem of the DDWPGS an electric-hydrogen hybrid energy storage system (HESS) for the DDWPGS is designed in this paper. Based on the characteristics of the devices in the electric-hydrogen HESS a new dynamic power allocation strategy and its control strategy are proposed. Firstly empirical mode decomposition (EMD) is utilized to allocate the power fluctuations that need to be stabilized. Secondly with the state of charge (SOC) of the battery and the operating characteristics of the alkaline electrolyzer being considered the power assignments of the battery and the electrolyzer are determined using the rule-based method. In addition model predictive control (MPC) with good tracking performance is used to adjust the output power of the battery and electrolyzer. Finally the supercapacitor (SC) is controlled to maintain the DC bus voltage while also balancing the system’s power. A simulation was established to verify the feasibility of the designed system. The results show that the electric-hydrogen HESS can stabilize the power fluctuations dynamically when the DDWPGS captures instantaneous power. Moreover its control strategy can not only reduce the start-stop times of the alkaline electrolyzer but also help the energy storage devices to maintain a good state and extend the service life.
Hydrogen Technology Towards the Solution of Environment-Friendly New Energy Vehicles
Aug 2021
Publication
The popularity of climate neutral new energy vehicles for reduced emissions and improved air quality has been raising great attention for many years. World-wide a strong commitment continues to drive the demand for zero-emission through alternative energy sources and propulsion systems. Despite the fact that 71.27% of hydrogen is produced from natural gas green hydrogen is a promising clean way to contribute to and maintain a climate neutral ecosystem. Thereby reaching CO2 targets for 2030 and beyond requires cross-sectoral changes. However the strong motivation of governments for climate neutrality is challenging many sectors. One of them is the transport sector as it is challenged to find viable all-in solutions that satisfy social economic and sustainable requirements. Currently the use of new energy vehicles operating on green sustainable hydrogen technologies such as batteries or fuel cells has been the focus for reducing the mobility induced emissions. In Europe 50% of the total emissions result from mobility. The following article reviews the background ongoing challenges and potentials of new energy vehicles towards the development of an environmentally friendly hydrogen economy. A change management process mindset has been adapted to discuss the key scientific and commercial challenges for a successful transition.
Environmental Benefit and Investment Value of Hydrogen-Based Wind-Energy Storage System
Mar 2021
Publication
Alongside the rapid expansion of wind power installation in China wind curtailment is also mounting rapidly due to China’s energy endowment imbalance. The hydrogen-based wind-energy storage system becomes an alternative to solve the puzzle of wind power surplus. This article introduced China’s energy storage industry development and summarized the advantages of hydrogen-based wind-energy storage systems. From the perspective of resource conservation it estimated the environmental benefits of hydrogen-based wind-energy storages. This research also builds a valuation model based on the Real Options Theory to capture the distinctive flexible charging and discharging features of the hydrogen-based wind-energy storage systems. Based on the model simulation results including the investment value and operation decision of the hydrogen energy storage system with different electricity prices system parameters and different levels of subsidies are presented. The results show that the hydrogen storage system fed with the surplus wind power can annually save approximately 2.19–3.29 million tons of standard coal consumption. It will reduce 3.31–4.97 million tons of CO2 SO2 NOx and PM saving as much as 286.6–429.8 million yuan of environmental cost annually on average. The hydrogen-based wind-energy storage system’s value depends on the construction investment and operating costs and is also affected by the meanreverting nature and jumps or spikes in electricity prices. The market-oriented reform of China’s power sector is conducive to improve hydrogen-based wind-energy storage systems’ profitability. At present subsidies are still essential to reduce initial investment and attract enterprises to participate in hydrogen energy storage projects.
Technology Roadmap for Hydrogen-fuelled Transportation in the UK
Apr 2023
Publication
Transportation is the sector responsible for the largest greenhouse gas emission in the UK. To mitigate its impact on the environment and move towards net-zero emissions by 2050 hydrogen-fuelled transportation has been explored through research and development as well as trials. This article presents an overview of relevant technologies and issues that challenge the supply use and marketability of hydrogen for transportation application in the UK covering on-road aviation maritime and rail transportation modes. The current development statutes of the different transportation modes were reviewed and compared highlighting similarities and differences in fuel cells internal combustion engines storage technologies supply chains and refuelling characteristics. In addition common and specific future research needs in the short to long term for the different transportation modes were suggested. The findings showed the potential of using hydrogen in all transportation modes although each sector faces different challenges and requires future improvements in performance and cost development of innovative designs refuelling stations standards and codes regulations and policies to support the advancement of the use of hydrogen.
Technology Portfolio Assessment for Near-zero Emission Iron and Steel Industry in China
May 2023
Publication
China aims to peak CO2 emissions before 2030 and to achieve carbon neutrality before 2060; hence industrial sectors in China are keen to figure out appropriate pathways to support the national target of carbon neutrality. The objective of this study is to explore near-zero emission pathways for the steel industry of China through a detailed technology assessment. The innovative technology development has been simulated using the AIM-China/steel model developed by including material-based technologies and optimal cost analysis. Six scenarios have been given in terms of different levels of production output emission reduction and carbon tax. Near-zero emission and carbon tax scenarios have shown that China’s steel industry can achieve near-zero emission using electric furnaces and hydrogen-based direct reduction iron technologies with policy support. Based on these technologies minimised production costs have been calculated revealing that the steel produced by these technologies is cost-effective. Moreover the feedstock cost can play a key role in these technology portfolios especially the cost of scrap iron ore and hydrogen. In addition the feedstock supply can have strong regional effects and can subsequently impact the allocation of steelmaking in the future. Therefore China can achieve near-zero emissions in the steel industry and electric furnace and hydrogen-based direct reduction iron technologies are crucial to achieving them.
Optimal Pathways for the Decarbonisation of the Transport Sector: Trade-offs Between Battery and Hydrogen Technologies Using a Whole Energy System Perspective
Jun 2023
Publication
Several countries have revised their targets in recent years to reach net-zero CO2 emissions across all sectors by 2050 and the transport sector is responsible for a significant share of these emissions. This study compares possible pathways to decarbonise the transport sector through electrification including passenger cars light commercial vehicles and heavy commercial vehicles. To do so we explore 125 scenarios by varying the share of battery and hydrogen-based fuel cell electric vehicles in each of the three categories above independently. We further model the decarbonisation of the industrial hydrogen demand using electrolysers with hydrogen storage. To explore the potential role of electric and hydrogen transport as well as their trade-offs we use GRIMSEL an open-source sector coupling energy system model of Switzerland which includes the residential commercial industrial and transport sectors with four energy carriers namely electricity heat hot water and hydrogen. The total costs are minimised from a social planner perspective. We find that the full electrification of the transport sector could lead on average to a 12% increase in costs by 2050 and 1.3 MtCO2/year which represents a 90% CO2 emissions reduction for the whole sector. Second the transport energy self-sufficiency (i.e. the share of domestic electricity generation in final transport demand) may reach up to 50% for the scenarios with the largest share of battery electric vehicles mainly due to a smaller energy demand than with hydrogen vehicles. Third more than three quarters of the industrial hydrogen production is met by local photovoltaic electricity coupled with battery at minimum costs i.e. green hydrogen. Finally the use of hydrogen as an energy carrier to store electricity over a long period is not cost-optimal.
Potential Role of Renewable Gas in the Transition of Electricity and District Heating Systems
Dec 2019
Publication
With the constant increase in variable renewable energy production in electricity and district heating systems integration with the gas system is a way to provide flexibility to the overall energy system. In the sustainable transition towards a zero-emission energy system traditional natural gas can be substituted by renewable gasses derived from anaerobic digestion or thermal gasification and hydrogen. In this paper we present a methodology for modelling renewable gas options and limits on biomass resources across sectors in the energy optimisation model Balmorel. Different scenarios for socio-economic pathways to emission neutral electricity and district heating systems in Denmark Sweden Norway and Germany show that a renewable based energy system benefits from a certain percentage of gas as a supplement to other flexibility options like interconnectors. Especially upgraded biogas from anaerobic digestion serves as a substitute for natural gas in all scenarios. Allocating only 10% of available biomass to the electricity and district heating sector leads to full exploitation of the scarce biomass resource by boosting biogas and syngas with hydrogen. The need for renewable gasses is highest in Germany and least in Norway where hydro-power provides flexibility in terms of storable and dispatchable electricity production. The scenarios show that a required ‘‘late sprint" from fossils to achieve a zero-emission energy system in 2050 causes (1) significant higher accumulated emissions and (2) a system which strongly relies on fuels also in an emission free system instead of stronger integration of the electricity and district heating systems through electrification as well as stronger integration of the power systems across countries through interconnectors.
Fast Sizing Methodology and Assessment of Energy Storage Configuration on the Flight Time of a Multirotor Aerial Vehicle
Apr 2023
Publication
Urban air mobility (UAM) defined as safe and efficient air traffic operations in a metropolitan area for manned aircraft and unmanned aircraft systems is being researched and developed by industry academia and government. This kind of mobility offers an opportunity to construct a green and sustainable sub-sector building upon the lessons learned over decades by aviation. Thanks to their non-polluting operation and simple air traffic management electric vertical take-off and landing (eVTOL) aircraft technologies are currently being developed and experimented with for this purpose. However to successfully complete the certification and commercialization stage several challenges need to be overcome particularly in terms of performance such as flight time and endurance and reliability. In this paper a fast methodology for sizing and selecting the propulsion chain components of an eVTOL multirotor aerial vehicle was developed and validated on a reduced-scale prototype of an electric multirotor vehicle with a GTOW of 15 kg. This methodology is associated with a comparative study of energy storage system configurations in order to assess their effect on the flight time of the aerial vehicle. First the optimal pair motor/propeller was selected using a global nonlinear optimization in order to maximize the specific efficiency of these components. Second five energy storage technologies were sized in order to evaluate their influence on the aerial vehicle flight time. Finally based on this sizing process the optimized propulsion chain gross take-off weight (GTOW) was evaluated for each energy storage configuration using regression-based methods based on propulsion chain supplier data.
Grid Ancillary Services using Electrolyzer-based Power-to-Gas Systems with Increasing Renewable Penetration
Nov 2023
Publication
Increasing penetrations of renewable-based generation have led to a decrease in the bulk power system inertia and an increase in intermittency and uncertainty in generation. Energy storage is considered to be an important factor to help manage renewable energy generation at greater penetrations. Hydrogen is a viable long-term storage alternative. This paper analyzes and presents use cases for leveraging electrolyzer-based power-to-gas systems for electric grid support. The paper also discusses some grid services that may favor the use of hydrogenbased storage over other forms such as battery energy storage. Real-time controls are developed implemented and demonstrated using a power-hardware-in-the-loop(PHIL) setup with a 225-kW proton-exchange-membrane electrolyzer stack. These controls demonstrate frequency and voltage support for the grid for different levels of renewable penetration (0% 25% and 50%). A comparison of the results shows the changes in respective frequencies and voltages as seen as different buses as a result of support from the electrolyzers and notes the impact on hydrogen production as a result of grid support. Finally the paper discusses the practical nuances of implementing the tests with physical hardware such as inverter/electrolyzer efficiency as well as the related constraints and opportunities.
The Use of Hydrogen for Traction in Freight Transport: Estimating the Reduction in Fuel Consumption and Emissions in a Regional Context
Jan 2023
Publication
The Italian National Recovery and Resilience Plan (NRRP) includes among other measures investments in hydrogen vehicle refuelling stations intending to promote the use of fuel cell electric vehicles (FCEVs) for long-haul freight transport. This paper evaluates the impact that this action could have on CO2 emissions and fuel consumption focusing on a case study of the Campania region. The proposed approach which can also be transferred to other geographical contexts requires the implementation of a freight road transport simulation model; this model is based on the construction of a supply model the estimation of road freight demand and an assignment procedure for computing traffic flows. This study covers the period from 2025 to 2040 according to the forecasts of the NRRP and some assumptions on the action effects; moreover it is assumed that hydrogen is entirely produced from renewable sources (green hydrogen). The key findings from three different scenarios show that savings between 423832 and 778538 tonnes of CO2 and between 144 and 264 million litres of diesel could be obtained.
Feasibility Assessment of Alternative Clean Power Systems onboard Passenger Short-Distance Ferry
Sep 2023
Publication
In order to promote low-carbon fuels such as hydrogen to decarbonize the maritime sector it is crucial to promote clean fuels and zero-emission propulsion systems in demonstrative projects and to showcase innovative technologies such as fuel cells in vessels operating in local public transport that could increase general audience acceptability thanks to their showcase potential. In this study a short sea journey ferry used in the port of Genova as a public transport vehicle is analyzed to evaluate a ”zero emission propulsion” retrofitting process. In the paper different types of solutions (batteries proton exchange membrane fuel cell (PEMFC) solid oxide fuel cell (SOFC)) and fuels (hydrogen ammonia natural gas and methanol) are investigated to identify the most feasible technology to be implemented onboard according to different aspects: ferry daily journey and scheduling available volumes and spaces propulsion power needs energy storage/fuel tank capacity needed economics etc. The paper presents a multi-aspect analysis that resulted in the identification of the hydrogen-powered PEMFC as the best clean power system to guarantee for this specific case study a suitable retrofitting of the vessel that could guarantee a zero-emission journey
Science and Technology of Ammonia Combustion
Nov 2018
Publication
This paper focuses on the potential use of ammonia as a carbon-free fuel and covers recent advances in the development of ammonia combustion technology and its underlying chemistry. Fulfilling the COP21 Paris Agreement requires the de-carbonization of energy generation through utilization of carbon-neutral and overall carbon-free fuels produced from renewable sources. Hydrogen is one of such fuels which is a potential energy carrier for reducing greenhouse-gas emissions. However its shipment for long distances and storage for long times present challenges. Ammonia on the other hand comprises 17.8% of hydrogen by mass and can be produced from renewable hydrogen and nitrogen separated from air. Furthermore thermal properties of ammonia are similar to those of propane in terms of boiling temperature and condensation pressure making it attractive as a hydrogen and energy carrier. Ammonia has been produced and utilized for the past 100 years as a fertilizer chemical raw material and refrigerant. Ammonia can be used as a fuel but there are several challenges in ammonia combustion such as low flammability high NOx emission and low radiation intensity. Overcoming these challenges requires further research into ammonia flame dynamics and chemistry. This paper discusses recent successful applications of ammonia fuel in gas turbines co-fired with pulverize coal and in industrial furnaces. These applications have been implemented under the Japanese ‘Cross-ministerial Strategic Innovation Promotion Program (SIP): Energy Carriers’. In addition fundamental aspects of ammonia combustion are discussed including characteristics of laminar premixed flames counterflow twin-flames and turbulent premixed flames stabilized by a nozzle burner at high pressure. Furthermore this paper discusses details of the chemistry of ammonia combustion related to NOx production processes for reducing NOx and validation of several ammonia oxidation kinetics models. Finally LES results for a gas-turbine-like swirl-burner are presented for the purpose of developing low-NOx single-fuelled ammonia gas turbine combustors.
Two-Layer Optimization Planning Model for Integrated Energy Systems in Hydrogen Refueling Original Station
May 2023
Publication
With the aggravation of global environmental pollution problems and the need for energy restructuring hydrogen energy as a highly clean resource has gradually become a hot spot for research in countries around the world. Facing the requirement of distributed hydrogen in refueling the original station for hydrogen transportation and other usage this paper proposes a comprehensive energy system planning model for hydrogen refueling stations to obtain the necessary devices construction the devices’ capacity decisions and the optimal operation behaviors of each device. Comparing to traditional single hydrogen producing technics in the traditional planning model the proposed model in this paper integrates both water-electrolysis-based and methanol-based manufacturing technics. A two-level optimization model is designed for this comprehensive system. The result of the numerical study shows that the proposed model can achieve a better optimal solution for distributed hydrogen production. Also it considers the single producing situation when price of one primary resource is sufficient higher than the other.
Modelling of Hydrogen-blended Dual-fuel Combustion using Flamelet-generated Manifold and Preferential Diffusion Effects
Oct 2022
Publication
In the present study Reynolds-Averaged Navier-Stokes simulations together with a novel flamelet generated manifold (FGM) hybrid combustion model incorporating preferential diffusion effects is utilised for the investigation of a hydrogen-blended diesel-hydrogen dual-fuel engine combustion process with high hydrogen energy share. The FGM hybrid combustion model was developed by coupling laminar flamelet databases obtained from diffusion flamelets and premixed flamelets. The model employed three control variables namely mixture fraction reaction progress variable and enthalpy. The preferential diffusion effects were included in the laminar flamelet calculations and in the diffusion terms in the transport equations of the control variables. The resulting model is then validated against an experimental diesel-hydrogen dual-fuel combustion engine. The results show that the FGM hybrid combustion model incorporating preferential diffusion effects in the flame chemistry and transport equations yields better predictions with good accuracy for the in-cylinder characteristics. The inclusion of preferential diffusion effects in the flame chemistry and transport equations was found to predict well several characteristics of the diesel-hydrogen dual-fuel combustion process: 1) ignition delay 2) start and end of combustion 3) faster flame propagation and quicker burning rate of hydrogen 4) high temperature combustion due to highly reactive nature of hydrogen radicals 5) peak values of the heat release rate due to high temperature combustion of the partially premixed pilot fuel spray with entrained hydrogen/air and then background hydrogen-air premixed mixture. The comparison between diesel-hydrogen dual-fuel combustion and diesel only combustion shows early start of combustion longer ignition delay time higher flame temperature and NOx emissions for dual-fuel combustion compared to diesel only combustion.
On the Use of a Hydrogen-Fueled Engine in a Hybrid Electric Vehicle
Dec 2022
Publication
Hybrid electric vehicles are currently one of the most effective ways to increase the efficiency and reduce the pollutant emissions of internal combustion engines. Green hydrogen produced with renewable energies is an excellent alternative to fossil fuels in order to drastically reduce engine pollutant emissions. In this work the author proposes the implementation of a hydrogen-fueled engine in a hybrid vehicle; the investigated hybrid powertrain is the power-split type in which the engine two electric motor/generators and the drive shaft are coupled together by a planetary gear set; this arrangement allows the engine to operate independently from the wheels and thus to exploit the best efficiency operating points. A set of numeric simulations were performed in order to compare the gasoline-fueled engine with the hydrogen-fueled one in terms of the thermal efficiency and total energy consumed during a driving cycle. The simulation results show a mean engine efficiency increase of around 17% when fueled with hydrogen with respect to gasoline and an energy consumption reduction of around 15% in a driving cycle.
Enhancement of Microgrid Frequency Stability Based on the Combined Power-to-Hydrogen-to-Power Technology under High Penetration Renewable Units
Apr 2023
Publication
Recently with the large-scale integration of renewable energy sources into microgrid (µGs) power electronics distributed energy systems have gained popularity. However low inertia reduces system frequency stability and anti-disturbance capabilities exposing power quality to intermittency and uncertainty in photovoltaics or wind turbines. To ensure system stability the virtual inertia control (VIC) is presented. This paper proposes two solutions to overcome the low inertia problem and the surplus in capacities resulting from renewable energy sources. The first solution employs superconducting magnetic energy storage (SMES) which can be deemed as an efficient solution for damping the frequency oscillations. Therefore in this work SMES that is managed by a simple proportional-integral-derivative controller (PID) controller is utilized to overcome the low inertia. In the second solution the hydrogen storage system is employed to maintain the stability of the microgrid by storing surplus power generated by renewable energy sources (RESs). Power-to-Power is a method of storing excess renewable energy as chemical energy in the form of hydrogen. Hydrogen can be utilized locally or delivered to a consumption node. The proposed µG operation demonstrates that the integration of the photovoltaics (PVs) wind turbines (WTs) diesel engine generator (DEG) electrolyzer micro gas turbine (µGT) and SMES is adequate to fulfill the load requirements under transient operating circumstances such as a low and high PV output power as well as to adapt to sudden changes in the load demand. The effectiveness of the proposed schemes is confirmed using real irradiance data (Benban City Egypt) using a MATLAB/SIMULINK environment.
Research on Energy Management of Hydrogen Fuel Cell Bus Based on Deep Reinforcement Learning Considering Velocity Control
Aug 2023
Publication
In the vehicle-to-everything scenario the fuel cell bus can accurately obtain the surrounding traffic information and quickly optimize the energy management problem while controlling its own safe and efficient driving. This paper proposes an energy management strategy (EMS) that considers speed control based on deep reinforcement learning (DRL) in complex traffic scenarios. Using SUMO simulation software (Version 1.15.0) a two-lane urban expressway is designed as a traffic scenario and a hydrogen fuel cell bus speed control and energy management system is designed through the soft actor–critic (SAC) algorithm to effectively reduce the equivalent hydrogen consumption and fuel cell output power fluctuation while ensuring the safe efficient and smooth driving of the vehicle. Compared with the SUMO–IDM car-following model the average speed of vehicles is kept the same and the average acceleration and acceleration change value decrease by 10.22% and 11.57% respectively. Compared with deep deterministic policy gradient (DDPG) the average speed is increased by 1.18% and the average acceleration and acceleration change value are decreased by 4.82% and 5.31% respectively. In terms of energy management the hydrogen consumption of SAC–OPT-based energy management strategy reaches 95.52% of that of the DP algorithm and the fluctuation range is reduced by 32.65%. Compared with SAC strategy the fluctuation amplitude is reduced by 15.29% which effectively improves the durability of fuel cells.
Modelling of Fast Fueling of Pressurized Hydrogen Tanks for Maritime Applications
Apr 2023
Publication
This paper studies fast fueling of gaseous hydrogen into large hydrogen (H2) tanks suitable for maritime applications. Three modeling methods have been developed and evaluated: (1) Two-dimensional computational fluid dynamic (CFD) modeling (2) One-dimensional wall discretized modeling and (3) Zero-dimensional modeling. A detailed 2D CFD simulation of a small H2-tank was performed and validated with data from literature and then used to simulate a large H2-tank. Results from the 2D-model show non-uniform temperature distribution inside the large tank but not in the small H2-tank. The 1D-model can predict the mean temperature in small H2-tanks but not the inhomogeneous temperature field in large H2-tanks. The 0D-model is suitable as a screening tool to obtain rough estimates. Results from the modeling of the large H2-tank show that the heat transfer to the wall during fast filling is inhibited by heat conduction in the wall which leads to an unacceptably high mean hydrogen temperature.
Energy Management Control Strategy for Saving Trip Costs of Fuel Cell/Battery Electric Vehicles
Mar 2022
Publication
Fuel cell vehicles (FCVs) should control the energy management between two energy sources for fuel economy using the stored energy in a battery or generation of energy through a fuel cell system. The fuel economy for an FCV includes trip costs for hydrogen consumption and the lifetime of two energy sources. This paper proposes an implementable energy management control strategy for an FCV to reduce trip costs. The concept of the proposed control strategy is first to analyze the allowable current of a fuel cell system from the optimal strategies for various initial battery state of charge (SOC) conditions using dynamic programming (DP) and second to find a modulation ratio determining the current of a fuel cell system for driving a vehicle using the particle swarm optimization method. The control strategy presents the on/off moment of a fuel cell system and the proper modulation ratio of the turned-on fuel cell system with respect to the battery SOC and the power demand. The proposed strategy reduces trip costs in real-time similar to the DP-based optimal strategy and more than the simple energy control strategy of switching a fuel cell system on/off at the battery SOC boundary conditions even for long-term driving cycles.
Fuel Cell Products for Sustainable Transportation and Stationary Power Generation: Review on Market Perspective
Mar 2023
Publication
The present day energy supply scenario is unsustainable and the transition towards a more environmentally friendly energy supply system of the future is inevitable. Hydrogen is a potential fuel that is capable of assisting with this transition. Certain technological advancements and design challenges associated with hydrogen generation and fuel cell technologies are discussed in this review. The commercialization of hydrogen-based technologies is closely associated with the development of the fuel cell industry. The evolution of fuel cell electric vehicles and fuel cell-based stationary power generation products in the market are discussed. Furthermore the opportunities and threats associated with the market diffusion of these products certain policy implications and roadmaps of major economies associated with this hydrogen transition are discussed in this review.
Preliminary Design of a Fuel Cell/Battery Hybrid Powertrain for a Heavy-duty Yard Truck for Port Logistics
Jun 2021
Publication
The maritime transport and the port-logistic industry are key drivers of economic growth although they represent major contributors to climate change. In particular maritime port facilities are typically located near cities or residential areas thus having a significant direct environmental impact in terms of air and water quality as well as noise. The majority of the pollutant emissions in ports comes from cargo ships and from all the related ports activities carried out by road vehicles. Therefore a progressive reduction of the use of fossil fuels as a primary energy source for these vehicles and the promotion of cleaner powertrain alternatives is in order. The present study deals with the design of a new propulsion system for a heavy-duty vehicle for port applications. Specifically this work aims at laying the foundations for the development of a benchmark industrial cargo–handling hydrogen-fueled vehicle to be used in real port operations. To this purpose an on-field measurement campaign has been conducted to analyze the duty cycle of a commercial Diesel-engine yard truck currently used for terminal ports operations. The vehicle dynamics has been numerically modeled and validated against the acquired data and the energy and power requirements for a plug-in fuel cell/battery hybrid powertrain replacing the Diesel powertrain on the same vehicle have been evaluated. Finally a preliminary design of the new powertrain and a rule-based energy management strategy have been proposed and the electric energy and hydrogen consumptions required to achieve the target driving range for roll-on and roll-off operations have been estimated. The results are promising showing that the hybrid electric vehicle is capable of achieving excellent energy performances by means of an efficient use of the fuel cell. An overall amount of roughly 12 kg of hydrogen is estimated to be required to accomplish the most demanding port operation and meet the target of 6 h of continuous operation. Also the vehicle powertrain ensures an adequate all-electric range which is between approximately 1 and 2 h depending on the specific port operation. Potentially the hydrogen-fueled yard truck is expected to lead to several benefits such as local zero emissions powertrain noise elimination reduction of the vehicle maintenance costs improving of the energy management and increasing of operational efficiency.
Numerical Predictions of a Swirl Combustor Using Complex Chemistry Fueled with Ammonia/Hydrogen Blends
Jan 2020
Publication
Ammonia a chemical that contains high hydrogen quantities has been presented as a candidate for the production of clean power generation and aerospace propulsion. Although ammonia can deliver more hydrogen per unit volume than liquid hydrogen itself the use of ammonia in combustion systems comes with the detrimental production of nitrogen oxides which are emissions that have up to 300 times the greenhouse potential of carbon dioxide. This factor combined with the lower energy density of ammonia makes new studies crucial to enable the use of the molecule through methods that reduce emissions whilst ensuring that enough power is produced to support high-energy intensive applications. Thus this paper presents a numerical study based on the use of novel reaction models employed to characterize ammonia combustion systems. The models are used to obtain Reynolds Averaged Navier-Stokes (RANS) simulations via Star-CCM+ with complex chemistry of a 70%–30% (mol) ammonia–hydrogen blend that is currently under investigations elsewhere. A fixed equivalence ratio (1.2) medium swirl (0.8) and confined conditions are employed to determine the flame and species propagation at various operating atmospheres and temperature inlet values. The study is then expanded to high inlet temperatures high pressures and high flowrates at different confinement boundary conditions. The results denote how the production of NOx emissions remains stable and under 400 ppm whilst higher concentrations of both hydrogen and unreacted ammonia are found in the flue gases under high power conditions. The reduction of heat losses (thus higher temperature boundary conditions) has a crucial impact on further destruction of ammonia post-flame with a raise in hydrogen water and nitrogen through the system thus presenting an opportunity of combustion efficiency improvement of this blend by reducing heat losses. Final discussions are presented as a method to raise power whilst employing ammonia for gas turbine systems.
Potential Transitions in the Iron and Steel Industry in Sweden: Towards a Hydrogen-based Future?
May 2018
Publication
The iron and steel industry accounts for one third of global industrial CO2 emissions putting pressure on the industry to shift towards more sustainable modes of production. However for an industry characterised by path dependency and technological lock-ins sustainability transitions are not straightforward. In this study we aim to explore the potential pathways for sustainability transitions in the iron and steel industry. To do so we have conducted a case study in Sweden where there are policy and industry commitments towards fossil-free steel production. Our theoretical points of departure are the technological innovation system (TIS) approach and the multi-level perspective (MLP) and our paper presents the dynamics behind an emerging case of transition towards a hydrogen-based future. The paper has two major contributions to the literature on sustainability transitions. First it attempts to borrow some concepts from the MLP and integrate them with the TIS approach. Second it empirically presents an in-depth case study of the iron and steel industry e an understudied context in the field of sustainability transitions. By doing so it sheds some light on the dynamics between an emerging TIS and potential transition pathways of a regime.
Techno-economic Assessment on Hybrid Energy Storage Systems Comprising Hydrogen and Batteries: A Case Study in Belgium
Jun 2023
Publication
This paper introduces a Techno-Economic Assessment (TEA) on present and future scenarios of different energy storage technologies comprising hydrogen and batteries: Battery Energy Storage System (BESS) Hydrogen Energy Storage System (H2ESS) and Hybrid Energy Storage System (HESS). These three configurations were assessed for different time horizons: 2019 2022 and 2030 under both on-grid and off-grid conditions. For 2030 a sensitivity analysis under different energy scenarios was performed covering other trends in on-grid electric consumption and prices CO2 taxation and the evolution of hydrogen technology prices from 2019 until 2030. The selected case study is the Research Park Zellik (RPZ) a CO2- neutral sustainable Local Energy Community (LEC) in Zellik Belgium. The software HOMER (Hybrid Optimisation Model for Electric Renewable) has been selected to design model and optimise the defined case study. The results showed that BESS was the most competitive when the electric grid was available among the three possible storage options. Additionally HESS was overall more competitive than H2ESS-only regardless of the grid connection mode. Finally as per HESS hydrogen was proved to play a complementary role when combined with batteries enhancing the flexibility of the microgrid and enabling deeper decarbonisation by reducing the electricity bought from the grid increasing renewable energy production and balancing toward an island operating mode.
On the Technology of Solid Oxide Fuel Cell (SOFC) Energy Systems for Stationary Power Generation: A Review
Nov 2022
Publication
This paper presents a comprehensive overview on the current status of solid oxide fuel cell (SOFC) energy systems technology with a deep insight into the techno-energy performance. In recent years SOFCs have received growing attention in the scientific landscape of high efficiency energy technologies. They are fuel flexible highly efficient and environmentally sustainable. The high working temperature makes it possible to work in cogeneration and drive downstream bottomed cycles such as Brayton and Hirn/Rankine ones thus configuring the hybrid system of a SOFC/turbine with very high electric efficiency. Fuel flexibility makes SOFCs independent from pure hydrogen feeding since hydrocarbons can be fed directly to the SOFC and then converted to a hydrogen rich stream by the internal thermochemical processes. SOFC is also able to convert carbon monoxide electrochemically thus contributing to energy production together with hydrogen. SOFCs are much considered for being supplied with biofuels especially biogas and syngas so that biomass gasifiers/SOFC integrated systems contribute to the “waste to energy” chain with a significant reduction in pollution. The paper also deals with the analysis of techno-energy performance by means of ad hoc developed numerical modeling in relation to the main operating parameters. Ample prominence is given to the aspect of fueling emphasizing fuel processing with a deep discussion on the impurities and undesired phenomena that SOFCs suffer. Constituent materials geometry and design methods for the balance of plant were studied. A wide analysis was dedicated to the hybrid system of the SOFC/turbine and to the integrated system of the biomass gasifier/SOFC. Finally an overview of SOFC system manufacturing companies on SOFC research and development worldwide and on the European roadmap was made to reflect the interest in this technology which is an important signal of how communities are sensitive toward clean low carbon and efficient technologies and therefore to provide a decisive and firm impulse to the now outlined energy transition.
Comprehensive Analysis of the Operation of an Internal Combustion Engine Fueled by Hydrogen-containing Mixtures
Mar 2023
Publication
At present hydrogen is considered as one of the most promising motor fuels capable of replacing traditional hydrocarbons. This article presents the results of a comprehensive experimental study of the effect of hydrogen additives on the main parameters of a gasoline spark-ignition ICE. The thermophysical parameters of the processes of ignition and combustion inside the cylinder with the addition of hydrogen in the amount of 0%–20% of the air volume as well as the fuel and energy characteristics of the engine and its impact on the environment were studied. It has been established that hydrogen leads to significant changes in the engine operation. It increases some parameters and reduces others improving or worsening them compared to running on pure gasoline. So with a 20% H2 addition at an average engine load the following parameters increase: the maximum pressure in the cylinder by almost 20%; the rate of pressure increase in the combustion chamber by 2.8 times; the highest combustion temperature by 140 K. At the same time the following parameters decrease: average indicator pressure by 18%; ignition timing by 82% (6◦ to TDC versus 34◦ for gasoline); crank angle corresponding to the maximum pressure by 32% (9.4◦ versus 13.9◦ for gasoline); crank angle corresponding to maximum temperature by 54% (17.7◦ after TDC versus 38.3◦ for clean gasoline); ignition delay time (τind = 0.32 ms) and visible combustion time (τvis = 1.58 ms) by 4 and 2.3 times respectively.
Optimized Design and Control of an Off Grid solar PV/hydrogen Fuel Cell Power System for Green Buildings
Sep 2017
Publication
Modelling simulation optimization and control strategies are used in this study to design a stand-alone solar PV/Fuel Cell/Battery/Generator hybrid power system to serve the electrical load of a commercial building. The main objective is to design an off grid energy system to meet the desired electric load of the commercial building with high renewable fraction low emissions and low cost of energy. The goal is to manage the energy consumption of the building reduce the associate cost and to switch from grid-tied fossil fuel power system to an off grid renewable and cleaner power system. Energy audit was performed in this study to determine the energy consumption of the building. Hourly simulations modelling and optimization were performed to determine the performance and cost of the hybrid power configurations using different control strategies. The results show that the hybrid off grid solar PV/Fuel Cell/Generator/Battery/Inverter power system offers the best performance for the tested system architectures. From the total energy generated from the off grid hybrid power system 73% is produced from the solar PV 24% from the fuel cell and 3% from the backup Diesel generator. The produced power is used to meet all the AC load of the building without power shortage (<0.1%). The hybrid power system produces 18.2% excess power that can be used to serve the thermal load of the building. The proposed hybrid power system is sustainable economically viable and environmentally friendly: High renewable fraction (66.1%) low levelized cost of energy (92 $/MWh) and low carbon dioxide emissions (24 kg CO2/MWh) are achieved.
Research on the Flexibility Margin of an Electric–Hydrogen Coupling Energy Block Based on Model Predictive Control
Apr 2022
Publication
Hydrogen energy plays an important role in the transformation of low-carbon energy and electric–hydrogen coupling will become a typical energy scenario. Aiming at the operation flexibility of a low-carbon electricity–hydrogen coupling system with high proportion of wind power and photovoltaic this work studies the flexibility margin of an electricity–hydrogen coupling energy block based on model predictive control. By analyzing the power exchange characteristics of heterogeneous energy the homogenization models of various heterogeneous energy sources are established. According to the analysis of power system flexibility margin three dimensions of flexibility margin evaluation indexes are defined from the dimension of system operation and an electricity–hydrogen coupling energy block scheduling model is established. The model predictive control algorithm is used to optimize the power balance operation of the electro–hydrogen coupling energy block and the flexibility margin of the energy block is quantitatively analyzed and calculated. Through the example analysis it is verified that the calculation method proposed in this article can not only realize the online power balance optimization of the electric–hydrogen coupling energy block but also effectively quantify the operation flexibility margin of the electric–hydrogen coupling energy block.
Review of Energy Portfolio Optimization in Energy Markets Considering Flexibility of Power-to-X
Mar 2023
Publication
Power-to-X is one of the most attention-grabbing topics in the energy sector. Researchers are exploring the potential of harnessing power from renewable technologies and converting it into fuels used in various industries and the transportation sector. With the current market and research emphasis on Power-to-X and the accompanying substantial investments a review of Power-to-X is becoming essential. Optimization will be a crucial aspect of managing an energy portfolio that includes Power-to-X and electrolysis systems as the electrolyzer can participate in multiple markets. Based on the current literature and published reviews none of them adequately showcase the state-of-the-art optimization algorithms for energy portfolios focusing on Power-to-X. Therefore this paper provides an in-depth review of the optimization algorithms applied to energy portfolios with a specific emphasis on Power-to-X aiming to uncover the current state-of-the-art in the field.
Well-To-Wheels Analysis of Future Automotive Fuels and Powertrains in the European Context
Jun 2014
Publication
The Well-to-Tank study describes the process of producing transporting manufacturing and distributing a number of fuels suitable for road transport powertrains. It covers all steps from extracting capturing or growing the primary energy carrier to refuelling the vehicles with the finished fuel.
A Multicriteria Modeling Approach for Evaluating Power Generation Scenarios Under Uncertainty: The Case of Green Hydrogen in Greece
Oct 2023
Publication
Clean energy technological innovations are widely acknowledged as a prerequisite to achieving ambitious longterm energy and climate targets. However the optimal speed of their adoption has been parsimoniously studied in the literature. This study seeks to identify the optimal intensity of moving to a green hydrogen electricity sector in Greece using the OSeMOSYS energy modeling framework. Green hydrogen policies are evaluated first on the basis of their robustness against uncertainty and afterwards against conflicting performance criteria and for different decision-making profiles towards risk by applying the VIKOR and TOPSIS multi-criteria decision aid methods. Although our analysis focuses exclusively on the power sector and compares different rates of hydrogen penetration compared to a business-as-usual case without considering other game-changing innovations (such as other types of storage or carbon capture and storage) we find that a national transition to a green hydrogen economy can support Greece in potentially cutting at least 16 MtCO2 while stimulating investments of EUR 10–13 bn. over 2030–2050.
Analysis of Power to Gas Technologies for Energy Intensive Industries in European Union
Jan 2023
Publication
Energy Intensive Industries (EII) are high users of energy and some of these facilities are extremely dependent on Natural Gas for processing heat production. In European countries where Natural Gas is mostly imported from external producers the increase in international Natural Gas prices is making it difficult for some industries to deliver the required financial results. Therefore they are facing complex challenges that could cause their delocalization in regions with lower energy costs. European countries lack on-site Natural Gas resources and the plans to reduce greenhouse gas emissions in the industrial sector make it necessary to find an alternative. Many different processes cannot be electrified and in these cases synthetic methane is one of the solutions and also represents an opportunity to reduce external energy supply dependency. This study analyzes the current development of power-to-gas technological solutions that could be implemented in large industrial consumers to produce Synthetic Methane using Green Hydrogen as a raw source and using Renewable Energy electricity mainly produced with photovoltaic or wind energy. The study also reviews the triple bottom line impact and the current development status and associated costs for each key component of a power-to-gas plant and the requirements to be fulfilled in the coming years to develop a cost-competitive solution available for commercial use.
Assessing the Sustainability of Liquid Hydrogen for Future Hypersonic Aerospace Flight
Dec 2022
Publication
This study explored the applications of liquid hydrogen (LH2 ) in aerospace projects followed by an investigation into the efficiency of ramjets scramjets and turbojets for hypersonic flight and the impact of grey blue and green hydrogen as an alternative to JP-7 and JP-8 (kerosene fuel). The advantage of LH2 as a propellant in the space sector has emerged from the relatively high energy density of hydrogen per unit volume enabling it to store more energy compared to conventional fuels. Hydrogen also has the potential to decarbonise space flight as combustion of LH2 fuel produces zero carbon emissions. However hydrogen is commonly found in hydrocarbons and water and thus it needs to be extracted from these molecular compounds before use. Only by considering the entire lifecycle of LH2 including the production phase can its sustainability be understood. The results of this study compared the predicted Life Cycle Assessment (LCA) emissions of the production of LH2 using grey blue and green hydrogen for 2030 with conventional fuel (JP-7 and JP-8) and revealed that the total carbon emissions over the lifecycle of LH2 were greater than kerosene-derived fuels.
Combustion Characteristics of Hydrogen in a Noble Gas Compression Ignition Engine
Jul 2021
Publication
Hydrogen eliminates carbon emissions from compression ignition (CI) engines while noble gases eliminate nitrogen oxide (NOx) emissions by replacing nitrogen. Noble gases can increase the in-cylinder temperature during the compression stroke due to their high specific heat ratio. This paper aims to find the optimum parameters for hydrogen combustion in an argon–oxygen atmosphere and to study hydrogen combustion in all noble gases providing hydrogen combustion data with suitable engine parameters to predict hydrogen ignitability under different conditions. Simulations are performed with Converge CFD software based on the Yanmar NF19SK direct injection CI (DICI) engine parameters. The results are validated with the experimental results of hydrogen combustion in an argon–oxygen atmosphere with a rapid compression expansion machine (RCEM) and modifications of the hydrogen injection timing and initial temperature are proposed. Hydrogen ignition in an argon atmosphere is dependent on a minimum initial temperature of 340 K but the combustion is slightly unstable. Helium and neon are found to be suitable for hydrogen combustion in low compression ratio (CR) engines. However krypton and xenon require temperature modification and a high CR for stable ignition. Detailed parameter recommendations are needed to improve hydrogen ignitability in conventional diesel engines with the least engine modification.
Investment Timing Analysis of Hydrogen-Refueling Stations and the Case of China: Independent or Co-Operative Investment?
Jun 2023
Publication
The investment in hydrogen-refueling stations (HRS) is key to the development of a hydrogen economy. This paper focuses on the decision-making for potential investors faced with the thought-provoking question of when the optimal timing to invest in HRS is. To fill the gap that exists due to the fact that few studies explain why HRS investment timing is critical we expound that earlier investment in HRS could induce the first mover advantages of the technology diffusion theory. Additionally differently from the previous research that only considered that HRS investment is just made by one individual firm we innovatively examine the HRS co-investment made by two different firms. Accordingly we compare these two optional investment modes and determine which is better considering either independent investment or co-operative investment. We then explore how the optimal HRS investment timing could be figured out under conditions of uncertainty with the real options approach. Given the Chinese HRS case under the condition of demand uncertainty the hydrogen demand required for triggering investment is viewed as the proxy for investment timing. Based on analytical and numerical results we conclude that one-firm independent investment is better than two-firm cooperative investment to develop HRS not only in terms of the earlier investment timing but also in terms of the attribute for dealing with the uncertainty. Finally we offer recommendations including stabilizing the hydrogen demand for decreasing uncertainty and accelerating firms’ innovation from both technological and strategic perspectives in order to ensure firms can make HRS investments on their own.
Combined Ammonia Recovery and Solid Oxide Fuel Cell Use at Wastewater Treatment Plants for Energy and Greenhouse Gas Emission Improvements
Feb 2019
Publication
Current standard practice at wastewater treatment plants (WWTPs) involves the recycling of digestate liquor produced from the anaerobic digestion of sludge back into the treatment process. However a significant amount of energy is required to enable biological breakdown of ammonia present in the liquor. This biological processing also results in the emission of damaging quantities of greenhouse gases making diversion of liquor and recovery of ammonia a noteworthy option for improving the sustainability of wastewater treatment. This study presents a novel process which combines ammonia recovery from diverted digestate liquor for use (alongside biomethane) in a solid oxide fuel cell (SOFC) system for implementation at WWTPs. Aspen Plus V.8.8 and numerical steady state models have been developed using data from a WWTP in West Yorkshire (UK) as a reference facility (750000p.e.). Aspen Plus simulations demonstrate an ability to recover 82% of ammoniacal nitrogen present in digestate liquor produced at the WWTP. The recovery process uses a series of stripping absorption and flash separation units where water is recovered alongside ammonia. This facilitates effective internal steam methane as a case of study has the potential to make significant impacts energetically and environmentally; findings suggest the treatment facility could transform from a net consumer of electricity to a net producer. The SOFC has been demonstrated to run at an electrical efficiency of 48% with NH3 contributing 4.6% of its power output. It has also been demonstrated that 3.5 kg CO2e per person served by the WWTP could be mitigated a year due to a combination of emissions savings by diversion of ammonia from biological processing and lifecycle emissions associated with the lack of reliance on grid electricity.
Source-to-sink Efficiency of Blue and Green District Heating and Hydrogen-based Heat Supply Systems
Apr 2022
Publication
Hydrogen is commonly mentioned as a future proof energy carrier. Hydrogen supporters 6 advocate for repurposing existing natural gas grids for a sustainable hydrogen supply. While the 7 long-term vision of the hydrogen community is green hydrogen the community acknowledges that 8 in the short term it will be to large extent manufactured from natural gas but in a decarbonized 9 way giving it the name blue hydrogen. While hydrogen has a role to play in hard to decarbonize 10 sectors its role for building heating demands is doubtful as mature and more energy efficient alter- 11 natives exist. As building heat supply infrastructures built today will operate for the decades to 12 come it is of highest importance to ensure that the most efficient and sustainable infrastructures are 13 chosen. This paper compares the source to sink efficiencies of hydrogen-based heat supply system 14 to a district heating system operating on the same primary energy source. The results show that a 15 natural gas-based district heating could be 267% more efficient and consequently have significantly 16 lower global warming potential than a blue hydrogen-based heat supply A renewable power-based 17 district heating could achieve above 440% higher efficiency than green hydrogen-based heat supply 18 system.
Optimal Sizing of Storage Elements for a Vehicle Based on Fuel Cells, Supercapacitors, and Batteries
Mar 2019
Publication
To achieve a vehicle-efficient energy management system an architecture composed of a PEM fuel cell as the main energy source and a hybrid storage system based on battery banks and supercapacitors is proposed. This paper introduces a methodology for the optimal component sizing aiming at minimizing the total cost achieving a cheaper system that can achieve the requirements of the speed profiles. The chosen vehicle is an urban transport bus which must meet the Buenos Aires Driving Cycle and the Manhattan Driving Cycle. The combination of batteries and supercapacitors allows a better response to the vehicle’s power demand since it combines the high energy density of the batteries with the high power density of the supercapacitors allowing the best absorption of energy coming from braking. In this way we address the rapid changes in power without reducing the global efficiency of the system. Optimum use of storage systems and fuel cell is analyzed through dynamic programming.
Techno-Economic Model for Scaling up of Hydrogen Refueling Stations
Oct 2022
Publication
In a recent publication the Hydrogen Council states that scaling up to greater production volumes leads to significant cost savings as a consequence of the industrialization of equipment manufacturing increased utilization standardization and improvements in system efficiency and flexibility. In this study a component-oriented techno-economic model is applied to five different European hydrogen refueling stations within the 3Emotion project which is planned to ensure capacities sufficient for increasing a fleet to 100 fuel cell buses. The investigation of the various cases shows that the levelized cost of hydrogen (LCOH) for large-scale applications will be in the range of about 4 €/kg to 7 €/kg within the boundaries analyzed. On-site production facilities were found to be the lower-cost design benefiting from the high volumes at stake and the economy of scale with respect to decentralized production due to the significant costs associated with retail hydrogen and transport. This study also illustrates the effects on the LCOH of varying the hydrogen delivery and production prices using a sensitivity analysis. The results show that by utilizing high-capacity trailers the costs associated with delivery could be reduced by 30%. Furthermore green hydrogen production could be a competitive solution if coupled with low electricity prices resulting in an LCOH between 4.21 €/kg and 6.80 €/kg.
Retrofitting Towards a Greener Marine Shipping Future: Reassembling Ship Fuels and Liquefied Natural Gas in Norway
Dec 2021
Publication
The reduction of greenhouse gas emissions has entered regulatory agendas in shipping. In Norway a debate has been ongoing for over a decade about whether liquefied natural gas (LNG) ship fuel enables or impedes the transition to a greener future for shipping. This paper explores the assembling of ship fuel before and after the introduction of a controversial carbon tax on LNG. It reconstructs how changes in the regulatory apparatus prompted the reworking of natural gas into a ship fuel yet later slowed down the development of LNG in a strategy to promote alternative zero-emission fuels such as hydrogen. Following ship fuel as socio-materiality in motion we find that fossil fuels are reworked into new modes of application as part of transition policies. Natural gas continues to be enacted as an “enabler of transition” in the context of shipping given that current government policies work to support the production of hydrogen from natural gas and carbon capture and storage (CCS). New modes of accounting for emissions reassemble existing fossil fuel materiality by means of CCS and fossil-based zero-emission fuels. We examine retrofit as a particular kind of reassembling and as a prism for studying the politics of fuel and the relation between transitions and existing infrastructures.
Everything About Hydrogen Podcast: Digging into the Mining Industry
Jan 2021
Publication
On this episode of Everything About Hydrogen Jan Klawitter Head of International Policy for Anglo American speaks with Andrew Chris and Patrick about Anglo American's strategy for decarbonizing its mining operations and how they plan to use hydrogen and fuel cell technologies as a key part of their approach.
The podcast can be found on their website
The podcast can be found on their website
Hydrogen Fuel for Future Mobility: Challenges and Future Aspects
Jul 2022
Publication
Nowadays the combustion of fossil fuels for transportation has a major negative impact on the environment. All nations are concerned with environmental safety and the regulation of pollution motivating researchers across the world to find an alternate transportation fuel. The transition of the transportation sector towards sustainability for environmental safety can be achieved by the manifestation and commercialization of clean hydrogen fuel. Hydrogen fuel for sustainable mobility has its own effectiveness in terms of its generation and refueling processes. As the fuel requirement of vehicles cannot be anticipated because it depends on its utilization choosing hydrogen refueling and onboard generation can be a point of major concern. This review article describes the present status of hydrogen fuel utilization with a particular focus on the transportation industry. The advantages of onboard hydrogen generation and refueling hydrogen for internal combustion are discussed. In terms of performance affordability and lifetime onboard hydrogen-generating subsystems must compete with what automobile manufacturers and consumers have seen in modern vehicles to date. In internal combustion engines hydrogen has various benefits in terms of combustive properties but it needs a careful engine design to avoid anomalous combustion which is a major difficulty with hydrogen engines. Automobile makers and buyers will not invest in fuel cell technology until the technologies that make up the various components of a fuel cell automobile have advanced to acceptable levels of cost performance reliability durability and safety. Above all a substantial advancement in the fuel cell stack is required.
Comprehensive Analysis of the Combustion of Low Carbon Fuels (Hydrogen, Methane and Coke Oven Gas) in a Spark Ignition Engine through CFD Modeling
Nov 2021
Publication
The use of low carbon fuels (LCFs) in internal combustion engines is a promising alternative to reduce pollution while achieving high performance through the conversion of the high energy content of the fuels into mechanical energy. However optimizing the engine design requires deep knowledge of the complex phenomena involved in combustion that depend on the operating conditions and the fuel employed. In this work computational fluid dynamics (CFD) simulation tools have been used to get insight into the performance of a Volkswagen Polo 1.4L port-fuel injection spark ignition engine that has been fueled with three different LCFs coke oven gas (COG) a gaseous by-product of coke manufacture H2 and CH4. The comparison is made in terms of power pressure temperature heat release flame growth speed emissions and volumetric efficiency. Simulations in Ansys® Forte® were validated with experiments at the same operating conditions with optimal spark advance wide open throttle a wide range of engine speed (2000–5000 rpm) and air-fuel ratio (λ) between 1 and 2. A sensitivity analysis of spark timing has been added to assess its impact on combustion variables. COG with intermediate flame growth speed produced the greatest power values but with lower pressure and temperature values at λ = 1.5 reducing the emissions of NO and the wall heat transfer. The useful energy released with COG was up to 16.5% and 5.1% higher than CH4 and H2 respectively. At richer and leaner mixtures (λ = 1 and λ = 2) similar performances were obtained compared to CH4 and H2 combining advantages of both pure fuels and widening the λ operation range without abnormal combustion. Therefore suitable management of the operating conditions maximizes the conversion of the waste stream fuel energy into useful energy while limiting emissions.
Climate Change Impacts of E-fuels for Aviation in Europe Under Present-day Conditions and Future Policy Scenarios
Jan 2023
Publication
‘E-fuels’ or ‘synthetic fuels’ are hydrocarbon fuels synthesized from hydrogen (H2) and carbon dioxide (CO2) where H2 can be produced via electrolysis of water or steam reforming of natural gas and CO2 is captured from the combustion of a fossil or biogenic source or directly from the atmosphere. E-fuels are drop-in substitutes for fossil fuels but their climate change mitigation benefits are largely unclear. This study evaluates the climate change impacts of e-fuels for aviation by combining different sources of CO2 and H2 up to 2050 under two contrasting policy scenarios. The analysis includes different climate metrics and the effects of near-term climate forcers which are particularly relevant for the aviation sector. Results are produced for European average conditions and for Poland and Norway two countries with high and low emission intensity from their electricity production mix. E-fuels can either have higher or lower climate change impacts than fossil fuels depending on multiple factors such as in order of importance the electricity mix the origin of CO2 the technology for H2 production and the electrolyzer efficiency. The climate benefits are generally higher for e-fuels produced from CO2 of biogenic origin while e-fuels produced from CO2 from direct air capture or fossil fuel combustion require countries with clean electricity to outperform fossil fuels. Synthetic fuels produced from H2 derived from natural gas have higher impacts than fossil fuels even when coupled with carbon capture and storage if CO2 is sourced from fossil fuels or the atmosphere. Climate change impacts of e-fuels improve in the future and they can all achieve considerable climate change mitigation in 2050 relative to fossil jet fuel provided that strict climate policy measures are implemented to decarbonize the electricity sector. Under reduced policy efforts future climate impacts in 2050 of e-fuels from atmospheric or fossil CO2 are still higher than those of fossil jet fuels with an average European electricity mix. This study shows the conditions to maximize the climate change mitigation benefits of e-fuels which essentially depend on progressive decarbonization of the electricity sector and on reduced use of CO2 sourced from fossil fuels.
Heat Pumps for Space Heating and Domestic Hot Water Production in Residential Buildings, an Environmental Comparison in a Present and Future Scenario
Nov 2022
Publication
The hydrogen vector stands as a potentially important tool to achieve the decarbonization of the energy sector. It represents an option to store the periodic excesses of energy generation from renewable electrical sources to be used as it is as a substitute for fossil fuels in some applications or reconverted into electricity when needed. In this context hydrogen can significantly decarbonize the building sector as an alternative fuel for gas-driven devices. Along with hydrogen the European strategic vision indicates the electrification of heat among the main energy transition pathways. The potential environmental benefits achievable from renewable hydrogen in thermally-driven appliances and the electrification of residential heat through electric heat pumps were evaluated and compared in this work. The novelty of the research consists of a consequential comparative life cycle assessment (16 impact categories) evaluation for three buildings (old old retrofitted and new) supplied by three different appliances (condensing boiler gas absorption heat pump and electric heat pump) never investigated before. The energy transition was evaluated for 2020 and 2030 scenarios considering the impact of gaseous fuels (natural gas and European green hydrogen) and electricity based on the pathway of the European electricity grid (27 European member states plus the United Kingdom). The results allowed to compare the environmental profile in deterministic and stochastic approaches and confirm if the increase of renewables reduces the impact in the operational phase of the appliances. The results demonstrate that despite the increased renewable share the use phase remains the most significant for both temporal scenarios contributing to 91% of the environmental profile. Despite the higher footprint in 2020 compared to the electric heat pump (198–200 vs. 170–196 gCO2eq/kWhth) the gas absorption heat pump offered a lower environmental profile than the others in all the scenarios analyzed.
HydroGenerally - Episode 5: Hydrogen for Glass Production
May 2022
Publication
In this fifth episode Steffan Eldred and Neelam Mughal from Innovate UK KTN discuss how the glass industry is driving new hydrogen developments and research and explore the hydrogen transition opportunities and challenges in this sector alongside their special guest Rob Ireson Innovation and Partnerships Manager at Glass Futures Ltd.
The podcast can be found on their website
The podcast can be found on their website
Electrification Versus Hydrogen for UK Road Freight: Conclusions from a Systems Analysis of Transport Energy Transitions
Mar 2022
Publication
Collectively the UK investment in transport decarbonisation is greater than £27B from government for incentivising zero-emission vehicles as part of an urgent response to decarbonise the transport sector. The investments made must facilitate a transition to a long-term solution. The success relies on coordinating and testing the evolution of both the energy and transport systems this avoids the risk of unforeseen consequences in both systems and therefore de-risks investment Here we present a semiquantitative energy and transport system analysis for UK road freight focusing on two primary investment areas for nation-wide decarbonisation namely electrification and hydrogen propulsion. Our study assembles and assesses the potential roadblocks of these energy systems into a concise record and considers the infrastructure in relation to all other components within the energy system. It highlights that for system-wide success and resilience a hydrogen system must overcome hydrogen production and distribution barriers whereas an electric system needs to optimise storage solutions and charging facilities. Without cohesive co-evolving energy networks the planning and operational modelling of transport decarbonisation may fall short of meaningful real-world results. A developed understanding of the dependencies between the energy and transport systems is a necessary step in the development of meaningful operational transport models that could de-risk investment in both the energy and transport systems.
Green Electricity and Medical Electrolytic Oxygen from Solar Energy - A Sustainable Solution for Rural Hospitals.
Oct 2022
Publication
The objective of this paper is to design and simulate for rural areas isolated from the electricity grid a system based on solar energy for the optimal supply of green electricity and medical oxygen to a hospital. The system sized to produce 20 Nm3 /day is constituted of a 37.46 kW photovoltaic farm a 15.47 kW electrolyzer and a 15.47 kW fuel cell. The simulation of the Photovoltaic system is performed using the single diode model solved with the Lambert function defined in MATLAB Software. The daily production of oxygen and hydrogen during the sunniest day of the month is respectively 20.81 Nm3 /day and 41.61 Nm3 /day. The daily energy that can be stored is relevant to the hydrogen production and an electricity storage capacity of 124.89 kWh is feasible. During the least sunny day of the least sunny month the daily production of oxygen and hydrogen is respectively 7.72 Nm3 /day and 15.44 Nm3 /day. The recorded values prove that the system sized can constitute a viable solution to ensure the permanent supply a green electricity and oxygen to the hospital with good energy storage capacity.
A Comprehensive Review of Electrochemical Hybrid Power Supply Systems and Intelligent Energy Managements for Unmanned Aerial Vehicles in Public Services
Jun 2022
Publication
The electric unmanned aerial vehicles (UAVs) are rapidly growing due to their abilities to perform some difficult or dangerous tasks as well as many public services including real-time monitoring wireless coverage search and rescue wildlife surveys and precision agriculture. However the electrochemical power supply system of UAV is a critical issue in terms of its energy/power densities and lifetime for service endurance. In this paper the current power supply systems used in UAVs are comprehensively reviewed and analyzed on the existing power configurations and the energy management systems. It is identified that a single type of electrochemical power source is not enough to support a UAV to achieve a long-haul flight; hence a hybrid power system architecture is necessary. To make use of the advantages of each type of power source to increase the endurance and achieve good performance of the UAVs the hybrid systems containing two or three types of power sources (fuel cell battery solar cell and supercapacitor) have to be developed. In this regard the selection of an appropriate hybrid power structure with the optimized energy management system is critical for the efficient operation of a UAV. It is found that the data-driven models with artificial intelligence (AI) are promising in intelligent energy management. This paper can provide insights and guidelines for future research and development into the design and fabrication of the advanced UAV power systems.
A Review on CO2 Mitigation in the Iron and Steel Industry through Power to X Processes
Feb 2021
Publication
In this paper we present the first systematic review of Power to X processes applied to the iron and steel industry. These processes convert renewable electricity into valuable chemicals through an electrolysis stage that produces the final product or a necessary intermediate. We have classified them in five categories (Power to Iron Power to Hydrogen Power to Syngas Power to Methane and Power to Methanol) to compare the results of the different studies published so far gathering specific energy consumption electrolysis power capacity CO2 emissions and technology readiness level. We also present for the first time novel concepts that integrate oxy-fuel ironmaking and Power to Gas. Lastly we round the review off with a summary of the most important research projects on the topic including relevant data on the largest pilot facilities (2–6 MW).
Optimization of Component Sizing for a Fuel Cell-Powered Truck to Minimize Ownership Cost
Mar 2019
Publication
In this study we consider fuel cell-powered electric trucks (FCETs) as an alternative to conventional medium- and heavy-duty vehicles. FCETs use a battery combined with onboard hydrogen storage for energy storage. The additional battery provides regenerative braking and better fuel economy but it will also increase the initial cost of the vehicle. Heavier reliance on stored hydrogen might be cheaper initially but operational costs will be higher because hydrogen is more expensive than electricity. Achieving the right tradeoff between these power and energy choices is necessary to reduce the ownership cost of the vehicle. This paper develops an optimum component sizing algorithm for FCETs. The truck vehicle model was developed in Autonomie a platform for modelling vehicle energy consumption and performance. The algorithm optimizes component sizes to minimize overall ownership cost while ensuring that the FCET matches or exceeds the performance and cargo capacity of a conventional vehicle. Class 4 delivery truck and class 8 linehaul trucks are shown as examples. We estimate the ownership cost for various hydrogen costs powertrain components ownership periods and annual vehicle miles travelled.
A General Vision for Reduction of Energy Consumption and CO2 Emissions from the Steel Industry
Aug 2020
Publication
The 2018 IPCC (The Intergovernmental Panel on Climate Change’s) report defined the goal to limit global warming to 1.5 ◦C by 2050. This will require “rapid and far-reaching transitions in land energy industry buildings transport and cities”. The challenge falls on all sectors especially energy production and industry. In this regard the recent progress and future challenges of greenhouse gas emissions and energy supply are first briefly introduced. Then the current situation of the steel industry is presented. Steel production is predicted to grow by 25–30% by 2050. The dominant iron-making route blast furnace (BF) especially is an energy-intensive process based on fossil fuel consumption; the steel sector is thus responsible for about 7% of all anthropogenic CO2 emissions. In order to take up the 2050 challenge emissions should see significant cuts. Correspondingly specific emissions (t CO2/t steel) should be radically decreased. Several large research programs in big steelmaking countries and the EU have been carried out over the last 10–15 years or are ongoing. All plausible measures to decrease CO2 emissions were explored here based on the published literature. The essential results are discussed and concluded. The specific emissions of “world steel” are currently at 1.8 t CO2/t steel. Improved energy efficiency by modernizing plants and adopting best available technologies in all process stages could decrease the emissions by 15–20%. Further reductions towards 1.0 t CO2/t steel level are achievable via novel technologies like top gas recycling in BF oxygen BF and maximal replacement of coke by biomass. These processes are however waiting for substantive industrialization. Generally substituting hydrogen for carbon in reductants and fuels like natural gas and coke gas can decrease CO2 emissions remarkably. The same holds for direct reduction processes (DR) which have spread recently exceeding 100 Mt annual capacity. More radical cut is possible via CO2 capture and storage (CCS). The technology is well-known in the oil industry; and potential applications in other sectors including the steel industry are being explored. While this might be a real solution in propitious circumstances it is hardly universally applicable in the long run. More auspicious is the concept that aims at utilizing captured carbon in the production of chemicals food or fuels e.g. methanol (CCU CCUS). The basic idea is smart but in the early phase of its application the high energy-consumption and costs are disincentives. The potential of hydrogen as a fuel and reductant is well-known but it has a supporting role in iron metallurgy. In the current fight against climate warming H2 has come into the “limelight” as a reductant fuel and energy storage. The hydrogen economy concept contains both production storage distribution and uses. In ironmaking several research programs have been launched for hydrogen production and reduction of iron oxides. Another global trend is the transfer from fossil fuel to electricity. “Green” electricity generation and hydrogen will be firmly linked together. The electrification of steel production is emphasized upon in this paper as the recycled scrap is estimated to grow from the 30% level to 50% by 2050. Finally in this review all means to reduce specific CO2 emissions have been summarized. By thorough modernization of production facilities and energy systems and by adopting new pioneering methods “world steel” could reach the level of 0.4–0.5 t CO2/t steel and thus reduce two-thirds of current annual emissions.
The Impact of Fuel Cell Electric Freight Vehicles on Fuel Consumption and CO2 Emissions: The Case of Italy
Oct 2022
Publication
The Italian Recovery and Resilience Plan promotes among its many actions the use of hydrogen by the deployment of refuelling stations for heavy-duty vehicles predicting a 5–7% penetration rate of fuel cell electric vehicles (FCEVs) for long-distance freight transport. In this work the impact of this action on the reduction of greenhouse gas emissions and consumption was estimated assuming the plan’s objectives are met. To achieve this aim a national simulation model of the road freight transport system was implemented consisting of a graph of the national road network and an inter-provincial origin-destination matrix; the graph was based on data available from OpenStreetMap while the interprovincial matrix was estimated from the interregional matrix with the use of two linear regression models one for emitted goods and one for attracted goods. The simulation of the system made it possible to estimate the impact of this action on CO2 emissions and fuel consumption under three different scenarios. From 2025 to 2040 a reduction in CO2 emissions ranging from around 9 to around 16.5 million tonnes was estimated and a reduction in consumption ranging from around 3 billion to around 5.6 billion litres of diesel. These results show how this action can be seen as one of the bricks contributing to the fight against global warming.
Economic Optima for Buffers in Direct Reduction Steelmaking Under Increasing Shares of Renewable Hydrogen
Oct 2021
Publication
While current climate targets demand substantial reductions in greenhouse gas (GHG) emissions the potentials to further reduce carbon dioxide emissions in traditional primary steel-making are limited. One possible solution that is receiving increasing attention is the direct reduction (DR) technology operated either with renewable hydrogen (H2) from electrolysis or with conventional natural gas (NG). DR technology makes it possible to decouple steel and hydrogen production by temporarily using overcapacities to produce and store intermediary products during periods of low renewable electricity prices or by switching between H2 and NG. This paper aims to explore the impact of this decoupling on overall costs and the corresponding dimensioning of production and storage capacities. An optimization model is developed to determine the least-cost operation based on perfect-foresight. This model can determine the minimum costs for optimal production and storage capacities under various assumptions considering fluctuating H2 and NG prices and increasing H2 shares. The model is applied to a case study for Germany and covers the current situation the medium term until 2030 and the long term until 2050. Under the assumptions made the role of using direct reduced iron (DRI) storage as a buffer seems less relevant. DRI mainly serves as long-term storage for several weeks similar to usual balancing storage capacities. Storing H2 on the contrary is used for short-term fluctuations and could balance H2 demand in the hourly range until 2050. From an economic perspective DRI production using NG tends to be cheaper than using H2 in the short term and potential savings from the flexible operation with storages are small at first. However in the long term until 2050 NG and H2 could achieve similar total costs if buffers are used. Otherwise temporarily occurring electricity price spikes imply substantial increases in total costs if high shares of H2 need to be achieved.
Integration of Hydrogen and Synthetic Natural Gas within Legacy Power Generation Facilities
Jun 2022
Publication
Whilst various new technologies for power generation are continuously being evaluated the owners of almost-new facilities such as combined-cycle gas turbine (CCGT) plants remain motivated to adapt these to new circumstances and avoid the balance-sheet financial impairments of underutilization. Not only are the owners reluctant to decommission the legacy CCGT assets but system operators value the inertia and flexibilities they contribute to a system becoming predominated with renewable generation. This analysis therefore focuses on the reinvestment cases for adapting CCGT to hydrogen (H2 ) synthetic natural gas (SNG) and/or retrofitted carbon capture and utilization systems (CCUS). Although H2 either by itself or as part of SNG has been evaluated attractively for longer-term electricity storage the business case for how it can be part of a hybrid legacy CCGT system has not been analyzed in a market context. This work compares the power to synthetic natural gas to power (PSNGP) adaptation with the simpler and less expensive power to hydrogen to power (P2HP) adaptation. Both the P2HP and PSNGP configurations are effective in terms of decarbonizations. The best results of the feasibility analysis for a UK application with low CCGT load factors (around 31%) were obtained for 100% H2 (P2HP) in the lower range of wholesale electricity prices (less than 178 GBP/MWh) but in the higher range of prices it would be preferable to use the PSNGP configuration with a low proportion of SNG (25%). If the CCGT load factor increased to 55% (the medium scenario) the breakeven profitability point between P2HP and PSNGP decreased to a market price of 145 GBP/MWh. Alternatively with the higher load factors (above 77%) satisfactory results were obtained for PSNGP using 50% SNG if with market prices above 185 GBP/MWh.
Cradle-grave Energy Consumption, Greenhouse Gas and Acidification Emissions in Current and Future Fuel Cell Vehicles: Study Based on Five Hydrogen Production Methods in China
Jun 2022
Publication
Hydrogen fuel cell vehicles (FCVs) are regarded as a promising solution to the problems of energy security and environmental pollution. However the technology is under development and the hydrogen consumption is uncertain. The quantitative evaluation of life cycle energy consumption pollution emissions of current and future FCVs in China involves complex processes and parameters. Therefore this study addresses Life Cycle Assessment (LCA) of FCV and focuses on the key parameters of FCV production and different hydrogen production methods which include steam methane reforming catalysis decomposition methanol steam reforming electrolysis–photovoltaic (PV) and electrolysis Chinese electricity grid mix (CN). Sensitivity analysis of bipolar plate glider mass power density fuel cell system efficiency and energy control strategy are performed whilst accounting for different assumption scenarios. The results show that all impact assessment indicators will decrease by 28.8– 44.3% under the 2030 positive scenario for the production of FCVs. For cradle-grave FCVs the use of hydrogen from electrolysis operated with photovoltaic power reduces global warming potential (GWP) by almost 76.4% relative to steam methane reforming. By contrast the use of hydrogen from electrolysis operated with the Chinese electricity grid mix results in an increase in GWP of almost 158.3%.
Experimental Study on Tri-fuel Combustion Using Premixed Methane-hydrogen Mixtures Ignited by a Diesel Pilot
Apr 2021
Publication
A comprehensive investigation on diesel pilot spray ignited methane-hydrogen (CH4–H2) combustion tri-fuel combustion (TF) is performed in a single-cylinder compression ignition (CI) engine. The experiments provide a detailed analysis of the effect of H2 concentration (based on mole fraction MH2) and charge-air temperature (Tair) on the ignition behavior combustion stability cycle-to-cycle (CCV) and engine performance. The results indicate that adding H2 from 0 to 60% shortens the ignition delay time (IDT) and combustion duration (based on CA90) up to 33% and 45% respectively. Thereby H2 helps to increase the indicated thermal efficiency (ITE) by as much as 10%. Furthermore to gain an insight into the combustion stability and CCV the short-time Fourier transform (STFT) and continuous wavelet transform (CWT) methodologies are applied to estimate the combustion stability and CCV of the TF combustion process. The results reveal that the pressure oscillation can be reduced up to 4 dB/Hz and the CCV by 50% when MH2 < 60% and Tair < 55 °C. However when MH2 > 60% and Tair > 40 °C abnormal combustion and knocking are observed.
Sustainable Synthetic Carbon Based Fuels for Transport
Sep 2019
Publication
The report considers two types of sustainable synthetic fuels: electro fuels (efuels) and synthetic biofuels. Efuels are made by combining hydrogen (from for example the electrolysis of water) with carbon dioxide (from direct air capture or a point source). Synthetic biofuels can be made from biological material (for example waste from forestry) or from further processing biofuels (for example ethanol).<br/>Whilst synthetic fuels can be “dropped in” to existing engines they are currently more expensive than fossil fuels and in the case of efuels could be thought of as an inefficient use of renewable electricity. However where renewable electricity is cheap and plentiful the manufacture and export of bulk efuels might make economic sense.<br/>Key research challenges identified include improving the fundamental understanding of catalysis; the need to produce cheap low-carbon hydrogen at scale; and developing sources of competitively priced low carbon energy are key to the development of synthetic efuels and biofuels. The UK has the research skills and capacity to improve many of these process steps such as in catalysis and biotechnology and to provide a further area of UK leadership in low-carbon energy.
The Path to Net Zero and Progress on Reducing Emissions in Wales
Dec 2020
Publication
These two joint reports required under the Environment (Wales) Act 2016 provide ministers with advice on Wales’ climate targets between now and 2050 and assess progress on reducing emissions to date. Our advice to the Welsh Government is set out in two parts:
Advice Report: The path to a Net Zero Wales provides recommendations on the actions that are needed in Wales including the legislation of a Net Zero target and package of policies to deliver it.
Progress Report: Reducing emissions in Wales looks back at the progress made in Wales since the 2016 Environment (Wales) Act was passed and assesses whether Wales is on track to meet its currently legislated emissions reductions targets.
This work is based on an extensive programme of analysis consultation and consideration by the Committee and its staff building on the evidence published last year for our Net Zero report. It is compatible with our advice on the UK’s Sixth Carbon Budget. In support of the advice in this report we have also published:
Advice Report: The path to a Net Zero Wales provides recommendations on the actions that are needed in Wales including the legislation of a Net Zero target and package of policies to deliver it.
Progress Report: Reducing emissions in Wales looks back at the progress made in Wales since the 2016 Environment (Wales) Act was passed and assesses whether Wales is on track to meet its currently legislated emissions reductions targets.
This work is based on an extensive programme of analysis consultation and consideration by the Committee and its staff building on the evidence published last year for our Net Zero report. It is compatible with our advice on the UK’s Sixth Carbon Budget. In support of the advice in this report we have also published:
- All the charts and data behind the report as well as a separate dataset for the scenarios which sets out more details and data on the pathways than can be included in this report.
- A public Call for Evidence several new research projects three expert advisory groups and deep dives into the roles of local authorities and businesses.
Improve Hydrogen Economy for Vehicular Fuel Cell System via Investigation and Control of Optimal Operating Oxygen Excess Ratio
Apr 2022
Publication
This study investigates and controls the optimal operating oxygen excess ratio (OER) for PEMFC which effectively prevents oxygen starvation and improves the hydrogen economy of proton exchange membrane fuel cells (PEMFC). Firstly the PEMFC output characteristic model and the five-order nonlinear air supply system model are established. Moreover an adaptive algebraic observer was developed to observe the partial pressure of gas in PEMFC and further reconstruct OER. Secondly to achieve the minimum hydrogen consumption under the required power the reference OER is determined by analyzing the PEMFC system output power with its minimum current. Finally the super-twisting algorithm is adopted to track reference OER. Simulation results show that the average absolute observation errors of oxygen nitrogen and cathode pressures under the Highway Fuel Economy Test are 1351.1 Pa (5.1%) 1724.2 Pa (0.9%) and 409.9 Pa (1.6%) respectively. The OER adjust average absolute error is 0.03. Compared with the commonly used fixed OER (e.g. OER of 1.5 and 2.3) the optimal OER strategy can reduce the hydrogen consumption of the PEMFC system by 5.2% and 1.8% respectively. Besides a DSP hardware in loop test is conducted to show the real-time performance of the proposed optimal method.
Boosting Carbon Efficiency of the Biomass to Liquid Process with Hydrogen from Power: The Effect of H2/CO Ratio to the Fischer-Tropsch Reactors on the Production and Power Consumption
Jun 2019
Publication
Carbon efficiency of a biomass to liquid process can be increased from ca. 30 to more than 90% by adding hydrogen generated from renewable power. The main reason is that in order to increase the H2/CO ratio after gasification to the value required for Fischer-Tropsch (FT) synthesis the water gas shift reaction step can be avoided; instead a reversed water gas shift reactor is introduced to convert produced CO2 to CO. Process simulations are done for a 46 t/h FT biofuel production unit. Previous results are confirmed and it is shown how the process can be further improved. The effect of changing the H2/CO ratio to the Fischer-Tropsch synthesis reactors is studied with the use of three different kinetic models. Keeping the CO conversion in the reactors constant at 55% the volume of the reactors decreases with increasing H2/CO ratio because the reaction rates increase with the partial pressure of hydrogen. Concurrently the production of C5+ products and the consumption of hydrogen increases. However the power required per extra produced liter fuel also increases pointing at optimum conditions at a H2/CO feed ratio significantly lower than 2. The trends are the same for all three kinetic models although one of the models is less sensitive to the hydrogen partial pressure. Finally excess renewable energy can be transformed to FT syncrude with an efficiency of 0.8–0.88 on energy basis.
Flexible Electricity Use for Heating in Markets with Renewable Energy
Mar 2020
Publication
Using electricity for heating can contribute to decarbonization and provide flexibility to integrate variable renewable energy. We analyze the case of electric storage heaters in German 2030 scenarios with an open-source electricity sector model. We find that flexible electric heaters generally increase the use of generation technologies with low variable costs which are not necessarily renewables. Yet making customary night-time storage heaters temporally more flexible offers only moderate benefits because renewable availability during daytime is limited in the heating season. Respective investment costs accordingly have to be very low in order to realize total system cost benefits. As storage heaters feature only short-term heat storage they also cannot reconcile the seasonal mismatch of heat demand in winter and high renewable availability in summer. Future research should evaluate the benefits of longer-term heat storage.
Dynamic Modeling of a PEM Fuel Cell Power Plant for Flexibility Optimization and Grid Support
Jun 2022
Publication
The transition toward high shares of non-programmable renewable energy sources in the power grid requires an increase in the grid flexibility to guarantee grid reliability and stability. This work developed within the EU project Grasshopper identifies hydrogen Fuel Cell (FC) power plants based on low temperature PEM cells as a source of flexibility for the power grid. A dynamic numerical model of the flexible FC system is developed and tested against experimental data from a 100-kW pilot plant built within the Grasshopper project. The model is then applied to assess the flexible performance of a 1 MW system in order to optimize the scale-up of the pilot plant to the MW-size. Simulations of load-following operation show the flexibility of the plant which can ramp up and down with a ramp rate depending only on an externally imposed limit. Warm-up simulations allow proposing solutions to limit the warm-up time. Of main importance are the minimization of the water inventory in the system and the construction of a compact system which minimizes the distance between the components.
An Adaptive Renewable Energy Plant (AREP) - To Power Local Premises and Vehicles with 100% Renewables
Aug 2021
Publication
An adaptive response renewable energy plant (AREP) that provides grid balancing services and XeV station fuelling services (where “X” is any type) using renewable energy located in urban centres is described. The AREP has its own primary renewable energy sources and adapts operation in the short term to changing levels of excess or deficient energy on LV and MV electricity grids. The AREP adaptively responds by (1) storing excess energy in batteries for the short term and in hydrogen tanks after energy conversion by electrolysers for the long term; (2) returning power to the grid from either the AREP’s own primary (electron-based) energy sources or batteries and/or from hydrogen via conversion in fuel cells; (3) providing electricity for fast charging BeVs and PHeVs and hydrogen for FCeVs; and (4) exporting excess stored energy as hydrogen to domestic markets. The AREP also adapts over the long term by predictive planning of charging capacity such that the type and capacity of renewable energy equipment is optimised for future operations. A key advantage of this AREP configuration is a flexible “plug and play” capability with modular extension of energy assets. If the AREP footprint is constrained interaction with neighbouring AREPs as a mini-VPP-AREP network can assist in balancing short-term operating requirements. The benefits of this grid balancing and XeV renewable energy filling station or AREP are environmental social and economic through efficient functionality of appropriately sized components. AREPs provide a net zero emissions electricity solution to an existing network with short and long-term storage options as well as a net zero emissions fuel alternative to the transport sector while leveraging existing infrastructure with minimal upfront CAPEX. AREPs can give the flexibility a grid needs to enable high levels of renewable installations while developing green hydrogen production.
Controlled Autoignition of Hydrogen in a Direct-injection Optical Engine
Mar 2021
Publication
Research into novel internal combustion engines requires consideration of the diversity in future fuels in an attempt to reduce drastically CO2 emissions from vehicles and promote energy sustainability. Hydrogen has been proposed as a possible fuel for future internal combustion engines and can be produced from renewable sources. Hydrogen’s wide flammability range allows higher engine efficiency than conventional fuels with both reduced toxic emissions and no CO2 gases. Most previous work on hydrogen engines has focused on spark-ignition operation. The current paper presents results from an optical study of controlled autoignition (or homogeneous charge compression ignition) of hydrogen in an engine of latest spark-ignition pentroof combustion chamber geometry with direct injection of hydrogen (100 bar). This was achieved by a combination of inlet air preheating in the range 200–400 C and residual gas recirculated internally by negative valve overlap. Hydrogen fuelling was set to various values of equivalence ratio typically in the range / = 0.40–0.63. Crank-angle resolved flame chemiluminescence images were acquired for a series of consecutive cycles at 1000 RPM in order to calculate in-cylinder rates of flame expansion and motion. Planar Laser Induced Fluorescence (LIF) of OH was also applied to record more detailed features of the autoignition pattern. Single and double (i.e. ‘split’ per cycle) hydrogen injection strategies were employed in order to identify the effect of mixture preparation on autoignition’s timing and spatial development. An attempt was also made to review relevant in-cylinder phenomena from the limited literature on hydrogen-fuelled spark-ignition optical engines and make comparisons were appropriate.
No more items...