China, People’s Republic
Investigation on the Effects of Blending Hydrogen-rich Gas in the Spark-ignition Engine
May 2022
Publication
In order to improve the energy efficiency of the internal combustion engine and replace fossil fuel with alternative fuels a concept of the methanol-syngas engine was proposed and the prototype was developed. Gasoline and dissociated methanol gas (GDM) were used as dual fuels and the engine performance was investigated by simulation and experiments. Dissociated methanol gas is produced by recycling the exhaust heat. The performance and combustion process was studied and compared with the gasoline engine counterpart. There is 1.9% energy efficiency improvement and 5.5% fuel consumption reduction under 2000r/min 100 N · m working condition with methanol substitution ratio of 10%. In addition the engine efficiency further improves with an increase of dissociated methanol gas substitution ratio because of the increased heating value of the fuel and effects of hydrogen. The peak pressure in the cylinder and the peak heat release rate of the GDM engine are higher than that of the original gasoline engine with a phase closer to the top dead center (TDC). Therefore blending hydrogen-rich gas in the spark-ignition engine can recycle the exhaust heat and improve the thermal efficiency of the engine.
An Ammonia-Hydrogen Energy Roadmap for Carbon Neutrality: Opportunity and Challenges in China
Nov 2021
Publication
China has promised to reach the peak carbon dioxide emission (ca. 10 billion tons) by 2030 and carbon neutrality by 2060. To realize these goals it is necessary to develop hydrogen energy and fuel cell techniques. However the high cost and low intrinsic safety of high-pressure hydrogen storage limit their commercialization. NH3 is high in hydrogen content easily liquefied at low pressure and free of carbon and the technology of NH3 synthesis has been commercialized nationwide. It is worth noting that the production of NH3 in China is about 56 million tons per year accounting for 35% of worldwide production. Hence with the well established infrastructure for NH3 synthesis and transportation and the demand for clean energy in China it is feasible to develop a green and economical energy roadmap viz. “Clean low-pressure NH3 synthesis → Safe and economical NH3 storage and transportation → Carbon-free efficient NH3-H2 utilization” for low-carbon or even carbon-free energy production.<br/>Currently the academic and industrial communities in China are striving to make technological breakthroughs in areas such as photocatalytic water splitting electrocatalytic water splitting mild-condition NH3 synthesis low-temperature NH3 catalytic decomposition and indirect or direct NH3 fuel cells with significant progress.<br/>Taking full advantage of the NH3 synthesis industry and readjusting the industrial structure it is viable to achieve energy saving and emission reduction in NH3 synthesis industry (440 million tons CO2 per year) as well as promote a new energy industry and ensure national energy security. Therefore relevant academic and industrial communities should put effort on mastering the key technologies of “Ammonia-Hydrogen” energy conversion and utilization with complete self-dependent intellectual property. It is envisioned that through the establishment of “Renewable Energy-Ammonia-Hydrogen” circular economy a green technology chain for hydrogen energy industry would pose as a promising pathway to achieve the 2030 and 2060 goals.
Simulation of Possible Fire and Explosion Hazards of Clean Fuel Vehicles in Garages
Nov 2021
Publication
Clean fuel is advocated to be used for sustainability. The number of liquefied petroleum gas (LPG) and hydrogen vehicles is increasing globally. Explosion hazard is a threat. On the other hand the use of hydrogen is under consideration in Hong Kong. Explosion hazards of these clean fuel (LPG and hydrogen) vehicles were studied and are compared in this paper. The computational fluid dynamics (CFD) software Flame Acceleration Simulator (FLACS) was used. A car garage with a rolling shutter as its entrance was selected for study. Dispersion of LPG from the leakage source with ignition at a higher position was studied. The same garage was used with a typical hydrogen vehicle leaking 3.4 pounds (1.5 kg) of hydrogen in 100 s the mass flow rate being equal to 0.015 kgs−1 . The hydrogen vehicle used in the simulation has two hydrogen tanks with a combined capacity of 5 kg. The entire tank would be completely vented out in about 333 s. Two scenarios of CFD simulation were carried out. In the first scenario the rolling shutter was completely closed and the leaked LPG or hydrogen was ignited at 300 s after leakage. The second scenario was conducted with a gap height of 0.3 m under the rolling shutter. Predicted results of explosion pressure and temperature show that appropriate active fire engineering systems are required when servicing these clean fuel vehicles in garages. An appropriate vent in an enclosed space such as the garage is important in reducing explosion hazards.
Investigation of Mixing Behavior of Hydrogen Blended to Natural Gas in Gas Network
Apr 2021
Publication
Hydrogen is of great significance for replacing fossil fuels and reducing carbon dioxide emissions. The application of hydrogen mixing with natural gas in gas network transportation not only improves the utilization rate of hydrogen energy but also reduces the cost of large-scale updating household or commercial appliance. This paper investigates the necessity of a gas mixing device for adding hydrogen to existing natural gas pipelines in the industrial gas network. A three-dimensional helical static mixer model is developed to simulate the mixing behavior of the gas mixture. In addition the model is validated with experimental results. Parametric studies are performed to investigate the effect of mixer on the mixing performance including the coefficient of variation (COV) and pressure loss. The research results show that based on the the optimum number of mixing units is three. The arrangement of the torsion angle of the mixing unit has a greater impact on the COV. When the torsion angle θ = 120◦ the COV has a minimum value of 0.66% and when the torsion angle θ = 60◦ the COV has a maximum value of 8.54%. The distance of the mixing unit has little effect on the pressure loss of the mixed gas but has a greater impact on the COV. Consecutive arrangement of the mixing units (Case A) is the best solution. Increasing the distance of the mixing unit is not effective for the gas mixing effect. Last but not least the gas mixer is optimized to improve the mixing performance.
Computational Intelligence Approach for Modeling Hydrogen Production: A Review
Mar 2018
Publication
Hydrogen is a clean energy source with a relatively low pollution footprint. However hydrogen does not exist in nature as a separate element but only in compound forms. Hydrogen is produced through a process that dissociates it from its compounds. Several methods are used for hydrogen production which first of all differ in the energy used in this process. Investigating the viability and exact applicability of a method in a specific context requires accurate knowledge of the parameters involved in the method and the interaction between these parameters. This can be done using top-down models relying on complex mathematically driven equations. However with the raise of computational intelligence (CI) and machine learning techniques researchers in hydrology have increasingly been using these methods for this complex task and report promising results. The contribution of this study is to investigate the state of the art CI methods employed in hydrogen production and to identify the CI method(s) that perform better in the prediction assessment and optimization tasks related to different types of Hydrogen production methods. The resulting analysis provides in-depth insight into the different hydrogen production methods modeling technique and the obtained results from various scenarios integrating them within the framework of a common discussion and evaluation paper. The identified methods were benchmarked by a qualitative analysis of the accuracy of CI in modeling hydrogen production providing extensive overview of its usage to empower renewable energy utilization.
Safety of Hydrogen Storage and Transportation: An Overview on Mechanisms, Techniques, and Challenges
Apr 2022
Publication
The extensive usage of fossil fuels has caused significant environmental pollution climate change and energy crises. The significant advantages of hydrogen such as cleanliness high efficiency and a wide range of sources make it quite promising. Hydrogen is prone to material damage which may lead to leakage. High-pressure leaking hydrogen is highly susceptible to spontaneous combustion due to its combustion characteristics which may cause jet fire or explosion accidents resulting in serious casualties and property damage. This paper presents a detailed review of the research progress on hydrogen leak diffusion characteristics leak spontaneous combustion mechanisms and material hydrogen damage mechanisms from the perspectives of theoretical analysis experiments and numerical simulations. This review points out that although a large number of research results have been obtained on the safety characteristics of hydrogen there are still some deficiencies and limitations. Further research topics are clarified such as further optimizing the kinetic mechanism of the high-pressure hydrogen leakage reaction and turbulence model exploring the expansion and dilution law of hydrogen clouds after liquid hydrogen flooding further studying the spontaneous combustion mechanism of leaked hydrogen and the interaction between mechanisms and investigating the synergistic damage effect of hydrogen and other components on materials. The leakage spontaneous combustion process in open space the development process of the bidirectional effect of hydrogen jet fuel and crack growth under the impact of high-pressure hydrogen jet fuel on the material may need to be explored next.
Flame Acceleration and Deflagration-to-Detonation Transition in Hydrogen-Oxygen Mixture in a Channel with Triangular Obstacles
Sep 2021
Publication
Study of flame acceleration and deflagration-to-detonation transition (DDT) in obstructed channels is an important subject of research for hydrogen safety. Experiments and numerical simulations of DDT in channels equipped with triangular obstacles were conducted in this work. High-speed schlieren photography and pressure records were used to study the flame shape changes flame propagation and pressure build up in the experiments. In the simulations the fully compressible reactive Navier–Stokes equations coupled with a calibrated chemical-diffusion model for stoichiometric hydrogen-oxygen mixture were solved using a high-order numerical method. The simulations were in good agreement with the experiments. The results show that the triangular obstacles significantly promote the flame acceleration and provide conditions for the occurrence of DDT. In the early stages of flame acceleration vortices are generated in the gaps between adjacent obstacles which is the main cause for the flame roll-up and distortion. A positive feedback mechanism between the combustiongenerated flow and flame propagation results in the variations of the size and velocity of vortices. The flame-vortex interactions cause flame fragmentation and consequently rapid growth in flame surface area which further lead to flame acceleration. The initially laminar flame then develops into a turbulent flame with the creation of shocks shock-flame interactions and various flame instabilities. The continuously arranged obstacles interact with shocks and flames and help to create environments in which a detonation can develop. Both flame collision and flame-shock interaction can give rise to detonation in the channels with triangular obstacles.
Hydrothermal Conversion of Lignin and Black Liquor for Phenolics with the Aids of Alkali and Hydrogen Donor
Jun 2019
Publication
The potentials of phenolic productions from lignin and black liquor (BL) via hydrothermal technology with the aids of alkalis and hydrogen donors were investigated by conducting batch experiments in micro-tube reactors with 300 °C sub-critical water as the solvent. The results showed that all the employed alkalis improved lignin degradation and thus phenolics production and the strong alkalis additionally manifested deoxygenation to produce more phenolics free of methoxyl group(s). Relatively hydrogen donors more visibly facilitated phenolics formation. Combination of strong alkali and hydrogen donors exhibited synergistically positive effects on producing phenolics (their total yield reaching 22 wt%) with high selectivities to phenolics among which the yields of catechol and cresols respectively peaked 16 and 3.5 wt%. BL could be hydrothermally converted into phenolics at high yields (approaching 10 wt% with the yields of catechol and cresols of about 4 and 2 wt% respectively) with the aids of its inherent alkali and hydrogen donors justifying its cascade utilization.
Transient Numerical Modeling and Model Predictive Control of an Industrial-scale Steam Methane Reforming Reactor
Mar 2021
Publication
A steam methane reforming reactor is a key equipment in hydrogen production and numerical analysis and process control can provide a critical insight into its reforming mechanisms and flexible operation in real engineering applications. The present paper firstly studies the transport phenomena in an industrial-scale steam methane reforming reactor by transient numerical simulations. Wall effect and local non thermal equilibrium is considered in the simulations. A temperature profile of the tube outer wall is given by user defined functions integrated into the ANSYS FLUENT software. Dynamic simulations show that the species distribution is closely related to the temperature distribution which makes the temperature of the reactor tube wall an important factor for the hydrogen production of the reformer and the thermal conductivity of the catalyst network is crucial in the heat transfer in the reactor. Besides there exists a delay of the reformer's hydrogen production when the temperature profile of the tube wall changes. Among inlet temperature inlet mass flow rate and inlet steam-to-carbon (S/C) ratio the mass flow rate is the most influencing factor for the hydrogen production. The dynamic matrix control (DMC) scheme is subsequently designed to manipulate the mole fraction of hydrogen of the outlet to the target value by setting the temperature profile trajectory of the reforming tube with time. The proportional-integral control strategy is also studied for comparison. The closed-loop simulation results show that the proposed DMC control strategy can reduce the overshoot and have a small change of the input variable. In addition the disturbances of feed disturbance can also be well rejected to assure the tracking performance indicating the superiority of the DMC controller. All the results give insight to the theoretical analysis and controller design of a steam methane reformer and demonstrate the potential of the CFD modeling in study the transport mechanism and the idea of combining CFD modelling with controller design for the real application.
Hydrogen Inhibition as Explosion Prevention in Wet Metal Dust Removal Systems
Mar 2022
Publication
Hydrogen energy attracts an amount of attention as an environmentally friendly and sustainable energy source. However hydrogen is also flammable. Hydrogen fires and explosions might occur in wet-dust-removal systems if accumulated aluminum dust reacts with water. Hydrogen inhibition is a safe method to address these issues. For this purpose we used sodium citrate a renewable and nontoxic raw material to inhibit H2 formation. Specifically hydrogen inhibition experiments with sodium citrate were carried out using custom-built equipment developed by our research group. When the concentration of sodium citrate solution was in the range of 0.4–4.0 g/L a protective coating was formed on the surface of the Al particles which prevented them from contacting with water. The inhibitory effect was achieved when the concentration of sodium citrate was in a certain range and too much or too little addition may reduce the inhibitory effect. In this paper we also discuss the economic aspects of H2 inhibition with this method because it offers excellent safety advantages and could be incorporated on a large scale. Such an intrinsic safety design of H2 inhibition to control explosions in wet-dust-removal systems could be applied to ensure the safety of other systems such as nuclear reactors.
An Improved Fuzzy PID Control Method Considering Hydrogen Fuel Cell Voltage-Output Characteristics for a Hydrogen Vehicle Power System
Sep 2021
Publication
The hydrogen fuel cell (HFC) vehicle is an important clean energy vehicle which has prospects for development. The behavior of the hydrogen fuel cell (HFC) vehicle power system and in particular the proton-exchange membrane fuel cell has been extensively studied as of recent. The development of the dynamic system modeling technology is of paramount importance for HFC vehicle studies; however it is hampered by the separation of the electrochemical properties and dynamic properties. In addition the established model matching the follow-up control method lacks applicability. In attempts to counter these obstructions we proposed an improved fuzzy (Proportional Integral Derivative) PID control method considering HFC voltage-output characteristics. By developing both the electrochemical and dynamic model for HFC vehicle we can realize the coordinated control of HFC and power cell. The simulation results are in good agreement with the experimental results in the two models. The proposed control algorithm has a good control effect in all stages of HFC vehicle operation.
Recent Progress on the Key Materials and Components for Proton Exchange Membrane Fuel Cells in Vehicle Applications
Jul 2016
Publication
Fuel cells are the most clean and efficient power source for vehicles. In particular proton exchange membrane fuel cells (PEMFCs) are the most promising candidate for automobile applications due to their rapid start-up and low-temperature operation. Through extensive global research efforts in the latest decade the performance of PEMFCs including energy efficiency volumetric and mass power density and low temperature startup ability have achieved significant breakthroughs. In 2014 fuel cell powered vehicles were introduced into the market by several prominent vehicle companies. However the low durability and high cost of PEMFC systems are still the main obstacles for large-scale industrialization of this technology. The key materials and components used in PEMFCs greatly affect their durability and cost. In this review the technical progress of key materials and components for PEMFCs has been summarized and critically discussed including topics such as the membrane catalyst layer gas diffusion layer and bipolar plate. The development of high-durability processing technologies is also introduced. Finally this review is concluded with personal perspectives on the future research directions of this area.
Hydrogen Production from the Air
Sep 2022
Publication
Green hydrogen produced by water splitting using renewable energy is the most promising energy carrier of the low-carbon economy. However the geographic mismatch between renewables distribution and freshwater availability poses a significant challenge to its production. Here we demonstrate a method of direct hydrogen production from the air namely in situ capture of freshwater from the atmosphere using hygroscopic electrolyte and electrolysis powered by solar or wind with a current density up to 574 mA cm−2 . A prototype of such has been established and operated for 12 consecutive days with a stable performance at a Faradaic efficiency around 95%. This so-called direct air electrolysis (DAE) module can work under a bone-dry environment with a relative humidity of 4% overcoming water supply issues and producing green hydrogen sustainably with minimal impact to the environment. The DAE modules can be easily scaled to provide hydrogen to remote (semi-) arid and scattered areas.
Safe Design of a Hydrogen-Powered Ship: CFD Simulation on Hydrogen Leakage in the Fuel Cell Room
Mar 2023
Publication
Adopting proton exchange membrane fuel cells fuelled by hydrogen presents a promising solution for the shipping industry’s deep decarbonisation. However the potential safety risks associated with hydrogen leakage pose a significant challenge to the development of hydrogen-powered ships. This study examines the safe design principles and leakage risks of the hydrogen gas supply system of China’s first newbuilt hydrogen-powered ship. This study utilises the computational fluid dynamics tool FLACS to analyse the hydrogen dispersion behaviour and concentration distributions in the hydrogen fuel cell room based on the ship’s parameters. This study predicts the flammable gas cloud and time points when gas monitoring points first reach the hydrogen volume concentrations of 0.8% and 1.6% in various leakage scenarios including four different diameters (1 3 5 and 10 mm) and five different directions. This study’s findings indicate that smaller hydrogen pipeline diameters contribute to increased hydrogen safety. Specifically in the hydrogen fuel cell room a single-point leakage in a hydrogen pipeline with an inner diameter not exceeding 3 mm eliminates the possibility of flammable gas cloud explosions. Following a 10 mm leakage diameter the hydrogen concentration in nearly all room positions reaches 4.0% within 6 s of leakage. While the leakage diameter does not impact the location of the monitoring point that first activates the hydrogen leak alarm and triggers an emergency hydrogen supply shutdown the presence of obstructions near hydrogen detectors and the leakage direction can affect it. These insights provide guidance on the optimal locations for hydrogen detectors in the fuel cell room and the pipeline diameters on hydrogen gas supply systems which can facilitate the safe design of hydrogen-powered ships.
New Liquid Chemical Hydrogen Storage Technology
Aug 2022
Publication
The liquid chemical hydrogen storage technology has great potentials for high-density hydrogen storage and transportation at ambient temperature and pressure. However its commercial applications highly rely on the high-performance heterogeneous dehydrogenation catalysts owing to the dehydrogenation difficulty of chemical hydrogen storage materials. In recent years the chemists and materials scientists found that the supported metal nanoparticles (MNPs) can exhibit high catalytic activity selectivity and stability for the dehydrogenation of chemical hydrogen storage materials which will clear the way for the commercial application of liquid chemical hydrogen storage technology. This review has summarized the recent important research progress in the MNP-catalyzed liquid chemical hydrogen storage technology including formic acid dehydrogenation hydrazine hydrate dehydrogenation and ammonia borane dehydrogenation discussed the urgent challenges in the key field and pointed out the future research trends.
Cow Dung Gasification Process for Hydrogen Production Using Water Vapor as Gasification Agent
Jun 2022
Publication
In recent years with the development of hydrogen energy economy there is an increasing demand for hydrogen in the market and hydrogen production through biomass will provide an important way to supply clean environmentally friendly and highly efficient hydrogen. In this study cow dung was selected as the biomass source and the efficiency of the biomass to hydrogen reaction was explored by coupling high temperature pyrolysis and water vapor gasification. The experimental conditions of gasification temperature water mass fraction heating rate and feed temperature were systematically studied and optimized to determine the optimal conditions for in situ hydrogen production by gasification of cow dung. The relationship of each factor to the yield of hydrogen production by gasification of cow dung semi-coke was investigated in order to elucidate the mechanism of the hydrogen production. The experiment determined the optimal operating parameters of in situ gasification: gasification temperature 1173 K water mass fraction 80% heating rate 10 K/min and feed temperature 673 K. The semi-coke treatment separated high temperature pyrolysis and water vapor gasification and reduced the influence on gasification of volatile substances such as tar extracted from pyrolysis. The increase of semi-coke preparation temperature increases the content of coke reduces the volatile matter and improves the yield of hydrogen; the small size of semi-coke particles and large specific surface area are beneficial to the gasification reaction.
Numerical Simulation on Hydrogen Leakage and Dispersion Behavior in Hydrogen Energy Infrastructures
Sep 2021
Publication
Unexpected hydrogen leakage may occur in the production storage transportation and utilization of hydrogen. The lower flammability limit (LFL) for the hydrogen is 4% in air. The combustion and explosion of hydrogen-air mixture poses potential hazards to personnel and property. In this study unintended release of hydrogen from a hydrogen fuel cell forklift vehicle inside a enclosed warehouse is simulated by fireFoam which is an LES Navier-Stokes CFD solver. The simulation results are verified by experimental data. The variation of hydrogen concentration with time and the isosurface of hydrogen concentration of 4% vol. are given. Furthermore the leakage of hydrogen from a storage tanks in a hydrogen refueling station is simulated and the evolution of the isosurface of hydrogen concentration of 4% vol. is given which provides a quantitative guidence for determination the hazardous area after the leakage of hydrogen.
Analysis of Crash Characteristics of Hydrogen Storage Structure of Hydrogen Powered UAV
Nov 2022
Publication
In the context of green aviation as an internationally recognized solution hydrogen energy is lauded as the “ultimate energy source of the 21st century” with zero emissions at the source. Developed economies with aviation industries such as Europe and the United States have announced hydrogen energy aviation development plans successively. The study and development of high-energy hydrogen fuel cells and hydrogen energy power systems have become some of the future aviation research focal points. As a crucial component of hydrogen energy storage and delivery the design and development of a safe lightweight and efficient hydrogen storage structure have drawn increasing consideration. Using a hydrogen-powered Unmanned Aerial Vehicle (UAV) as the subject of this article the crash characteristics of the UAV’s hydrogen storage structure are investigated in detail. The main research findings are summarized as follows: (1) A series of crash characteristics analyses of the hydrogen storage structure of a hydrogen-powered UAV were conducted and the Finite Element Analysis (FEA) response of the structure under different impact angles internal pressures and impact speeds was obtained and analyzed. (2) When the deformation of the hydrogen storage structure exceeds 50 mm and the strain exceeds 0.8 an initial crack will appear at this part of the hydrogen storage structure. The emergency release valve should respond immediately to release the gas inside the tank to avoid further damage. (3) Impact angle and initial internal pressure are the main factors affecting the formation of initial cracks.
Influence of Hydrogen Production in the CO2 Emissions Reduction of Hydrogen Mettalurgy Transformation in Iron and Steel Industry
Jan 2023
Publication
The transformation of hydrogen metallurgy is a principal means of promoting the iron and steel industry (ISI) in reaching peak and deep emissions reduction. However the environmental impact of different hydrogen production paths on hydrogen metallurgy has not been systemically discussed. To address this gap based on Long-range Energy Alternatives Planning System (LEAP) this paper constructs a bottom-up energy system model that includes hydrogen production iron and steel (IS) production and power generation. By setting three hydrogen production structure development paths namely the baseline scenario business-as-usual (BAU) scenario and clean power (CP) scenario the carbon dioxide (CO2) emissions impact of different hydrogen production paths on hydrogen metallurgy is carefully evaluated from the perspective of the whole industry and each IS production process. The results show that under the baseline scenario the hydrogen metallurgy transition will help the CO2 emissions of ISI peak at 2.19 billion tons in 2024 compared to 2.08 billion tons in 2020 and then gradually decrease to 0.78 billion tons in 2050. However different hydrogen production paths will contribute to the reduction or inhibit the reduction. In 2050 the development of electrolysis hydrogen production with renewable electricity will reduce CO2 emissions by an additional 48.76 million tons (under the CP scenario) while the hydrogen production mainly based on coal gasification and methane reforming will increase the additional 50.04 million tons CO2 emissions (under the BAU scenario). Moreover under the hydrogen production structure relying mainly on fossil and industrial by-products the technological transformation of blast furnace ironmaking with hydrogen injections will leak carbon emissions to the upstream energy processing and conversion process. Furthermore except for the 100% scrap based electric arc furnace (EAF) process the IS production process on hydrogen-rich shaft furnace direct reduced iron (hydrogen-rich DRI) have lower CO2 emissions than other processes. Therefore developing hydrogen-rich DRI will help the EAF steelmaking development to efficiently reduce CO2 emissions under scrap constraints.
Review on the Hydrogen Dispersion and the Burning Behavior of Fuel Cell Electric Vehicles
Oct 2022
Publication
The development of a hydrogen energy-based society is becoming the solution for more and more countries. Fuel cell electric vehicles are the best carriers for developing a hydrogen energy-based society. The current research on hydrogen leakage and the diffusion of fuel cell electric vehicles has been sufficient. However the study of hydrogen safety has not reduced the safety concerns for society and government management departments concerning the large-scale promotion of fuel cell electric vehicles. Hydrogen safety is both a technical and psychological issue. This paper aims to provide a comprehensive overview of fuel cell electric vehicles’ hydrogen dispersion and the burning behavior and introduce the relevant work of international standardization and global technical regulations. The CFD simulations in tunnels underground car parks and multistory car parks show that the hydrogen escape performance is excellent. At the same time the research verifies that the flow the direction of leakage and the vehicle itself are the most critical factors affecting hydrogen distribution. The impact of the leakage location and leakage pore size is much smaller. The relevant studies also show that the risk is still controllable even if the hydrogen leakage rate is increased ten times the limit of GTR 13 to 1000 NL/min and then ignited. Multi-vehicle combustion tests of fuel cell electric vehicles showed that adjacent vehicles were not ignited by the hydrogen. This shows that as long as the appropriate measures are taken the risk of a hydrogen leak or the combustion of fuel cell electric vehicles is controllable. The introduction of relevant standards and regulations also indirectly proves this point. This paper will provide product design guidelines for R&D personnel offer the latest knowledge and guidance to the regulatory agencies and increase the public’s acceptance of fuel cell electric vehicles.
Numerical Study on Protective Measures for a Skid-Mounted Hydrogen Refueling Station
Jan 2023
Publication
Hydrogen refueling stations are one of the key infrastructure components for the hydrogen-fueled economy. Skid-mounted hydrogen refueling stations (SHRSs) can be more easily commercialized due to their smaller footprints and lower costs compared to stationary hydrogen refueling stations. The present work modeled hydrogen explosions in a skid-mounted hydrogen refueling station to predict the overpressures for hydrogen-air mixtures and investigate the protective effects for different explosion vent layouts and protective wall distances. The results show that the explosive vents with the same vent area have similar overpressure reduction effects. The layout of the explosion vent affects the flame shape. Explosion venting can effectively reduce the inside maximum overpressure by 61.8%. The protective walls can reduce the overpressures but the protective walls should not be too close to the SHRS because high overpressures are generated inside the walls due to the confined shock waves. The protective wall with a distance of 6 m can effectively protect the surrounding people and avoid the secondary overpressure damage to the container.
Hydrogen Leakage Simulation and Risk Analysis of Hydrogen Fueling Station in China
Sep 2022
Publication
Hydrogen is a renewable energy source with various features clean carbon-free high energy density which is being recognized internationally as a “future energy.” The US the EU Japan South Korea China and other countries or regions are gradually clarifying the development position of hydrogen. The rapid development of the hydrogen energy industry requires more hydrogenation infrastructure to meet the hydrogenation need of hydrogen fuel cell vehicles. Nevertheless due to the frequent occurrence of hydrogen infrastructure accidents their safety has become an obstacle to large-scale construction. This paper analyzed five sizes (diameters of 0.068 mm 0.215 mm 0.68 mm 2.15 mm and 6.8 mm) of hydrogen leakage in the hydrogen fueling station using Quantitative Risk Assessment (QRA) and HyRAM software. The results show that unignited leaks occur most frequently; leaks caused by flanges valves instruments compressors and filters occur more frequently; and the risk indicator of thermal radiation accident and structure collapse accident caused by over-pressure exceeds the Chinese individual acceptable risk standard and the risk indicator of a thermal radiation accident and head impact accident caused by overpressure is below the Chinese standard. On the other hand we simulated the consequences of hydrogen leak from the 45 MPa hydrogen storage vessels by the physic module of HyRAM and obtained the ranges of plume dispersion jet fire radiative heat flux and unconfined overpressure. We suggest targeted preventive measures and safety distance to provide references for hydrogen fueling stations’ safe construction and operation.
A Real-Time Load Prediction Control for Fuel Cell Hybrid Vehicle
May 2022
Publication
The development of hydrogen energy is an effective solution to the energy and environmental crisis. Hydrogen fuel cells and energy storage cells as hybrid power have broad application prospects in the field of vehicle power. Energy management strategies are key technologies for fuel cell hybrid systems. The traditional optimization strategy is generally based on optimization under the global operating conditions. The purpose of this project is to develop a power allocation optimization method based on real-time load forecasting for fuel cell/lithium battery hybrid electric vehicles which does not depend on specific working conditions or causal control methods. This paper presents an energy-management algorithm based on real-time load forecasting using GRU neural networks to predict load requirements in the short time domain and then the local optimization problem for each predictive domain is solved using a method based on Pontryagin’s minimum principle (PMP). The algorithm adopts the idea of model prediction control (MPC) to transform the global optimization problem into a series of local optimization problems. The simulation results show that the proposed strategy can achieve a good fuel-saving control effect. Compared with the rule-based strategy and equivalent hydrogen consumption strategy (ECMS) the fuel consumption is lower under two typical urban conditions. In the 1800 s driving cycle under WTCL conditions the fuel consumption under the MPC-PMP strategy is 22.4% lower than that based on the ECMS strategy and 10.3% lower than the rules-based strategy. Under CTLT conditions the fuel consumption of the MPC-PMP strategy is 13.12% lower than that of the rule-based strategy and 3.01% lower than the ECMS strategy.
Roadmap to Hybrid Offshore System with Hydrogen and Power Co-generation
Sep 2021
Publication
Constrained by the expansion of the power grid the development of offshore wind farms may be hindered and begin to experience severe curtailment or restriction. The combination of hydrogen production through electrolysis and hydrogen-to-power is considered to be a potential option to achieve the goal of low-carbon and energy security. This work investigates the competitiveness of different system configurations to export hydrogen and/or electricity from offshore plants with particular emphasis on unloading the mixture of hydrogen and electricity to end-users on land. Including the levelized energy cost and net present value a comprehensive techno-economic assessment method is proposed to analyze the offshore system for five scenarios. Assuming that the baseline distance is 10 km the results show that exporting hydrogen to land through pipelines shows the best economic performance with the levelized energy cost of 3.40 $/kg. For every 10 km increase in offshore distance the net present value of the project will be reduced by 5.69 MU$ and the project benefit will be positive only when the offshore distance is less than 53.5 km. An important finding is that the hybrid system under ship transportation mode is not greatly affected by the offshore distance. Every 10% increase in the proportion of hydrogen in the range of 70%–100% can increase the net present value by 1.43–1.70 MU$ which will increase by 7.36–7.37 MU$ under pipeline transportation mode. Finally a sensitivity analysis was carried out to analyze the wind speed electricity and hydrogen prices on the economic performance of these systems.
Thermodynamics and Kinetics of Hydriding and Dehydriding Reactions in Mg-based Hydrogen Storage Materials
Oct 2021
Publication
Mg-based materials are one of the most promising hydrogen storage candidates due to their high hydrogen storage capacity environmental benignity and high Clarke number characteristics. However the limited thermodynamics and kinetic properties pose major challenges for their engineering applications. Herein we review the recent progress in improving their thermodynamics and kinetics with an emphasis on the models and the influence of various parameters in the calculated models. Subsequently the impact of alloying composite and nano-crystallization on both thermodynamics and dynamics are discussed in detail. In particular the correlation between various modification strategies and the hydrogen capacity dehydrogenation enthalpy and temperature hydriding/dehydriding rates are summarized. In addition the mechanism of hydrogen storage processes of Mg-based materials is discussed from the aspect of classical kinetic theories and microscope hydrogen transferring behavior. This review concludes with an outlook on the remaining challenge issues and prospects.
Influence of Hydrogen Environment on Fatigue Fracture Morphology of X80 Pipeline Steel
Dec 2022
Publication
The rapid development of hydrogen energy requires the use of natural gas infrastructure for hydrogen transportation. It is very important to study hydrogen-added natural gas transportation technology which is a key way to rapidly develop coal-based gas and renewable energy. This study aims to study the influence of X80 pipeline steel's fatigue performance in hydrogen environment and perform fatigue tests on notched round rod specimens under different hydrogen concentration. The experimental results show that hydrogen seriously affects the fatigue life of pipeline steel. After reaching a certain hydrogen concentration as the hydrogen concentration continues to increase the fatigue life decreases gradually. Combined with SEM analysis of fracture morphology the decrease in the size and density of the dimples reduces the displacement amplitude while the increase in the planar area increases the displacement during fatigue fracture due to accelerated crack propagation. From this study we can know the influence of hydrogen concentration on the fracture morphology of pipeline steel which provides an understanding of the effect of hydrogen on fatigue fracture morphology and a broader safety analysis.
Scenario-Based Comparative Analysis for Coupling Electricity and Hydrogen Storage in Clean Oilfield Energy Supply System
Mar 2022
Publication
In response to the objective of fully attaining carbon neutrality by 2060 people from all walks of life are pursuing low-carbon transformation. Due to the high water cut in the middle and late phases of development the oilfield’s energy consumption will be quite high and the rise in energy consumption will lead to an increase in carbon emission at the same time. As a result the traditional energy model is incapable of meeting the energy consumption requirement of high water cut oilfields in their middle and later phases of development. The present wind hydrogen coupling energy system was researched and coupled with the classic dispersed oilfield energy system to produce energy for the oilfields in this study. This study compares four future energy system models to existing ones computes the energy cost and net present value of an oilfield in Northwest China and proposes a set of economic evaluation tools for oilfield energy systems. The study’s findings indicate that scenario four provides the most economic and environmental benefits. This scenario effectively addresses the issue of high energy consumption associated with aging oilfields at this point significantly reduces carbon emissions absorbs renewable energy locally and reduces the burden on the power grid system. Finally sensitivity analysis is utilized to determine the effect of wind speed electricity cost and oilfield gas output on the system’s economic performance. The results indicate that the system developed in this study can be applied to other oilfields.
Sustainable Offshore Oil and Gas Fields Development: Techno-economic Feasibility Analysis of Wind–hydrogen–natural Gas Nexus
Jul 2021
Publication
Offshore oil and gas field development consumes quantities of electricity which is usually provided by gas turbines. In order to alleviate the emission reduction pressure and the increasing pressure of energy saving governments of the world have been promoting the reform of oil and gas fields for years. Nowadays environmentally friendly alternatives to provide electricity are hotspots such as the integration of traditional energy and renewable energy. However the determination of system with great environmental and economic benefits is still controversial. This paper proposed a wind– hydrogen–natural gas nexus (WHNGN) system for sustainable offshore oil and gas fields development. Combining the optimization model with the techno-economic evaluation model a comprehensive evaluation framework is established for techno-economic feasibility analysis. In addition to WHNGN system another two systems are designed for comparison including the traditional energy supply (TES) system and wind–natural gas nexus (WNGN) system. An offshore production platforms in Bohai Bay in China is taken as a case and the results indicate that: (i) WNGN and WHNGN systems have significant economic benefits total investment is decreased by 5190 and 5020 million $ respectively and the WHNGN system increases 4174 million $ profit; (ii) WNGN and WHNGN systems have significant environmental benefits annual carbon emission is decreased by 15 and 40.2 million kg respectively; (iii) the system can be ranked by economic benefits as follows: WHNGN >WNGN > TES; and (iV) the WHNGN system is more advantageous in areas with high hydrogen and natural gas sales prices such as China Kazakhstan Turkey India Malaysia and Indonesia.
Research on Hydrogen Consumption and Driving Range of Hydrogen Fuel Cell Vehicle under the CLTC-P Condition
Dec 2021
Publication
Hydrogen consumption and mileage are important economic indicators of fuel cell vehicles. Hydrogen consumption is the fundamental reason that restricts mileage. Since there are few quantitative studies on hydrogen consumption during actual vehicle operation the high cost of hydrogen consumption in outdoor testing makes it impossible to guarantee the accuracy of the test. Therefore this study puts forward a test method based on the hydrogen consumption of fuel cell vehicles under CLTC-P operating conditions to test the hydrogen consumption of fuel cell vehicles per 100 km. Finally the experiment shows that the mileage calculated by hydrogen consumption has a higher consistency with the actual mileage. Based on this hydrogen consumption test method the hydrogen consumption can be accurately measured and the test time and cost can be effectively reduced.
An Effective Optimisation Method for Coupled Wind–Hydrogen Power Generation Systems Considering Scalability
Jan 2023
Publication
A wind–hydrogen coupled power generation system can effectively reduce the power loss caused by wind power curtailment and further improve the ability of the energy system to accommodate renewable energy. However the feasibility and economy of deploying such a power generation system have not been validated through large‐scale practical applications and the economic comparison between regions and recommendations on construction are still lacking. In order to solve the aforementioned problems this paper establishes an economic analysis model for the wind–hydrogen coupled power generation system and proposes a linear optimisation‐based priority analysis method focusing on the major net present value for regional energy system as well as a cost priority analysis method for hydrogen production within sample power plants. The case study proves the effectiveness of the proposed analysis methods and the potential to develop wind–hydrogen coupled power generation systems in various provinces is compared based on the national wind power data in recent years. This provides recommendations for the future pilot construction and promotion of wind–hydrogen coupled power generation systems in China.
Effect of Hydrogen-blended Natural Gas on Combustion Stability and Emission of Water Heater Burner
Jun 2022
Publication
To study the effect of hydrogen-blended natural gas on the combustion stability and emission of domestic gas water heater a test system is built in this paper taking a unit of the partial premixed burner commonly used in water heaters as the object. Under the heat load of 0.7~2.3kW the changes of flame shape burner temperature and pollutant emission of natural gas with hydrogen volume ratio of 0~40% are studied with independent control of primary air supply and mixing. The results show that: with the increase of hydrogen blending ratio the inner flame height increases firstly and then reduces while the change of burner temperature is opposite. The maximum inner flame height and the minimum temperature of the burner both appear at the hydrogen blending ratio of 10~20%. It can be seen that the limit of hydrogen blending ratio which can maintain the burner operate safely and stably under rated heat load is 40% through the maximum temperature distribution on the burner surface. The CO emission in the flue gas gradually decreases with the increase of hydrogen blending ratio while the NOx emission fluctuates slightly when the hydrogen blending ratio is less than 20% but then decreases gradually.
A Review on Numerical Simulation of Hydrogen Production from Ammonia Decomposition
Jan 2023
Publication
Ammonia (NH3 ) is regarded as a promising medium of hydrogen storage due to its large hydrogen storage density decent performance on safety and moderate storage conditions. On the user side NH3 is generally required to decompose into hydrogen for utilization in fuel cells and therefore it is vital for the NH3 -based hydrogen storage technology development to study NH3 decomposition processes and improve the decomposition efficiency. Numerical simulation has become a powerful tool for analyzing the NH3 decomposition processes since it can provide a revealing insight into the heat and mass transfer phenomena and substantial guidance on further improving the decomposition efficiency. This paper reviews the numerical simulations of NH3 decomposition in various application scenarios including NH3 decomposition in microreactors coupled combustion chemical reactors solid oxide fuel cells and membrane reactors. The models of NH3 decomposition reactions in various scenarios and the heat and mass transport in the reactor are elaborated. The effects of reactor structure and operating conditions on the performance of NH3 decomposition reactor are analyzed. It can be found that NH3 decomposition in microchannel reactors is not limited by heat and mass transfer and NH3 conversion can be improved by using membrane reactors under the same conditions. Finally research prospects and opportunities are proposed in terms of model development and reactor performance improvement for NH3 decomposition.
Exergy and Exergoeconomic Analysis for the Proton Exchange Membrane Water Electrolysis under Various Operating Conditions and Design Parameters
Nov 2022
Publication
Integrating the exergy and economic analyses of water electrolyzers is the pivotal way to comprehend the interplay of system costs and improve system performance. For this a 3D numerical model based on COMSOL Multiphysics Software (version 5.6 COMSOL Stockholm Sweden) is integrated with the exergy and exergoeconomic analysis to evaluate the exergoeconomic performance of the proton exchange membrane water electrolysis (PEMWE) under different operating conditions (operating temperature cathode pressure current density) and design parameter (membrane thickness). Further the gas crossover phenomenon is investigated to estimate the impact of gas leakage on analysis reliability under various conditions and criteria. The results reveal that increasing the operating temperature or decreasing the membrane thickness improves both the efficiency and cost of hydrogen exergy while increasing the gas leakage through the membrane. Likewise raising the current density and the cathode pressure lowers the hydrogen exergy cost and improves the economic performance. The increase in exergy destroyed and hydrogen exergy cost as well as the decline in second law efficiency due to the gas crossover are more noticeable at higher pressures. As the cathode pressure rises from 1 to 30 bar at a current density of 10000 A/m2 the increase in exergy destroyed and hydrogen exergy cost as well as the decline in second law efficiency are increased by 37.6 kJ/mol 4.49 USD/GJ and 7.1% respectively. The cheapest green electricity source which is achieved using onshore wind energy and hydropower reduces hydrogen production costs and enhances economic efficiency. The growth in the hydrogen exergy cost is by about 4.23 USD/GJ for a 0.01 USD/kWh increase in electricity price at the current density of 20000 A/m2. All findings would be expected to be quite useful for researchers engaged in the design development and optimization of PEMWE.
A Review of Key Components of Hydrogen Recirculation Subsystem for Fuel Cell Vehicles
Jul 2022
Publication
Hydrogen energy and fuel cell technology are critical clean energy roads to pursue carbon neutrality. The proton exchange membrane fuel cell (PEMFC) has a wide range of commercial application prospects due to its simple structure easy portability and quick start-up. However the cost and durability of the PEMFC system are the main barriers to commercial applications of fuel cell vehicles. In this paper the core hydrogen recirculation components of fuel cell vehicles including mechanical hydrogen pumps ejectors and gas–water separators are reviewed in order to understand the problems and challenges in the simulation design and application of these components. The types and working characteristics of mechanical pumps used in PEMFC systems are summarized. Furthermore corresponding design suggestions are given based on the analysis of the design challenges of the mechanical hydrogen pump. The research on structural design and optimization of ejectors for adapting wide power ranges of PEMFC systems is analyzed. The design principle and difficulty of the gas–water separator are summarized and its application in the system is discussed. In final the integration and control of hydrogen recirculation components controlled cooperatively to ensure the stable pressure and hydrogen supply of the fuel cell under dynamic loads are reviewed.
Experimental Study on Flame Characteristics of Cryogenic Hydrogen Jet Fire
Sep 2021
Publication
In this work cryogenic hydrogen fires at fixed pressures and various initial temperatures were investigated experimentally. Flame length width heat fluxes and temperatures in down-stream regions were measured for the scenarios with 1.6-3 mm jet nozzle 106 to 273 K 2-5 barabs. The results show that the flame size is related to not only the jet nozzle diameter but also the release pressure and initial temperature. The correlations of normalized flame length and width are proposed with the stagnation pressure and the ratio of ambient and stagnation temperatures. Under constant pressure the flame size total radiative power and radiation fraction increase with the decrease of temperature due to lower choked flow velocity and higher density of cryogenic hydrogen. The correlation of radiation fraction proposed by Molina et al. at room temperature is not suitable to predict the cryogenic hydrogen jet fires. Based on piecewise polynomial law
Progress and Prospects of Hydrogen Production: Opportunities and challenges
Jan 2021
Publication
This study presents an overview of the current status of hydrogen production in relation to the global requirement for energy and resources. Subsequently it symmetrically outlines the advantages and disadvantages of various production routes including fossil fuel/biomass conversion water electrolysis microbial fermentation and photocatalysis (PC) in terms of their technologies economy energy consumption and costs. Considering the characteristics of hydrogen energy and the current infrastructure issues it highlights that onsite production is indispensable and convenient for some special occasions. Finally it briefly summarizes the current industrialization situation and presents future development and research directions such as theoretical research strengthening renewable raw material development process coupling and sustainable energy use.
Investigation on the Changes of Pressure and Temperature in High Pressure Filling of Hydrogen Storage Tank
May 2022
Publication
Hydrogen as fuel has been considered as a feasible energy carry and which offers a clean and efficient alternative for transportation. During the high pressure filling the temperature in the hydrogen storage tank (HST) may rise rapidly due to the hydrogen compression. The high temperature may lead to safety problem. Thus for fast and safely refueling the hydrogen several key factors need to be considered. In the present study by the thermodynamics theories a mathematical model is established to simulate and analyze the high pressure filling process of the storage tank for the hydrogen station. In the analysis the physical parameters of normal hydrogen are introduced to make the simulation close to the actual process. By the numerical simulation for 50 MPa compressed hydrogen tank the temperature and pressure trends during filling are obtained. The simulation results for non-adiabatic filling were compared with the theoretically calculated ones for adiabatic conditions and the simulation results for non-adiabatic filling were compared with the simulation ones for adiabatic conditions. Then the influence of working pressure initial temperature mass flow rate initial pressure and inlet temperature on the temperature rise were analyzed. This study provides a theoretical research basis for high pressure hydrogen energy storage and hydrogenation technology.
Numerical Modeling for Rapid Charging of Hydrogen Gas Vessel in Fuel Cell Vehicle
Feb 2023
Publication
As a fuel for power generation high-pressure hydrogen gas is widely used for transportation and its efficient storage promotes the development of fuel cell vehicles (FCVs). However as the filling process takes such a short time the maximum temperature in the storage tank usually undergoes a rapid increase which has become a thorny problem and poses great technical challenges to the steady operation of hydrogen FCVs. For security reasons SAE J2601/ISO 15869 regulates a maximum temperature limit of 85 ◦C in the specifications for refillable hydrogen tanks. In this paper a two-dimensional axisymmetric and a three-dimensional numerical model for fast charging of Type III 35 MPa and 70 MPa hydrogen vehicle cylinders are proposed in order to effectively evaluate the temperature rise within vehicle tanks. A modified standard k-ε turbulence model is utilized to simulate hydrogen gas charging. The equation of state for hydrogen gas is adopted with the thermodynamic properties taken from the National Institute of Standards and Technology (NIST) database taking into account the impact of hydrogen gas’ compressibility. To validate the numerical model three groups of hydrogen rapid refueling experimental data are chosen. After a detailed comparison it is found that the simulated results calculated by the developed numerical model are in good agreement with the experimental results with average temperature differences at the end time of 2.56 K 4.08 K and 4.3 K. The present study provides a foundation for in-depth investigations on the structural mechanics analysis of hydrogen gas vessels during fast refueling and may supply some technical guidance on the design of charging experiments.
Computational Investigation of Combustion, Performance, and Emissions of a Diesel-Hydrogen Dual-Fuel Engine
Feb 2023
Publication
This paper aims to expose the effect of hydrogen on the combustion performance and emissions of a high-speed diesel engine. For this purpose a three-dimensional dynamic simulation model was developed using a reasonable turbulence model and a simplified reaction kinetic mechanism was chosen based on experimental data. The results show that in the hydrogen enrichment conditions hydrogen causes complete combustion of diesel fuel and results in a 17.7% increase in work capacity. However the increase in combustion temperature resulted in higher NOx emissions. In the hydrogen substitution condition the combustion phases are significantly earlier with the increased hydrogen substitution ratio () which is not conducive to power output. However when the is 30% the CO soot and THC reach near-zero emissions. The effect of the injection timing is also studied at an HSR of 90%. When delayed by 10° IMEP improves by 3.4% compared with diesel mode and 2.4% compared with dual-fuel mode. The NOx is reduced by 53% compared with the original dual-fuel mode. This study provides theoretical guidance for the application of hydrogen in rail transportation.
Oxygen Carriers for Chemical-looping Water Splitting to Hydrogen Production: A Critical Review
Oct 2021
Publication
Chemical looping water splitting (CLWS) process using metal oxides or perovskites as oxygen carriers (OCs) is capable of producing pure H2 in an efficient simple and flexible way. The OCs are first reduced by hydrocarbon fuels and then oxidized by steam in a cyclic way. After the condensation of the gaseous mixture of steam and H2 from the oxidation step pure H2 is obtained. In recent years great efforts for CLWS have been made to improve the redox activity and stability of OCs. In this paper the development of the OCs for hydrogen production from CLWS were discussed. Effects of supports and additives on the performances of OCs were compared based on redox reactions in CLWS. Fe-based OCs with CeO2 Al2O3 ZrO2 CuO MoO3 Rh etc. are very attractive for the CLWS process. Issues and challenges for the development of OCs were analyzed.
Experiment and Numerical Study of the Combustion Behavior of Hydrogen-blended Natural Gas in Swirl Burners
Oct 2022
Publication
Hydrogen production from renewable energy is gaining increasing attention to enhance energy consumption structure and foster a more eco-friendly and sustainable society. At the same time mixing hydrogen with natural gas and supplying it to civilians is one of the best ways to reduce carbon emissions and increase the reliability of technology while reducing the costs of storing and transporting hydrogen. Even though numerous researchers have conducted experimental and simulation studies on hydrogen-doped natural gas most of these studies have focused on the effects of hydrogen-doped ratio equivalence ratio and fuel combustion mode. The impact of burner structure on hydrogen-enriched natural gas has not received much attention. Compared with conventional direct-flow combustion swirl combustion can improve the mixing effect of the fuel mixture during combustion and the use of regions of reversed flow due to swirl can make the fuel burn more fully to achieve the reduction of pollutant emissions. Swirling flames are widely used in gas turbines and industrial furnaces because of their high stability. However the application of swirl combustion in domestic equipment is still in its infancy which deserves more researchers to explore and enhance the working conditions of domestic combustion equipment. In this paper a three-dimensional swirl burner model is utilized to examine the effect of swirl angle θ and swirl length L of the swirler on the combustion behavior of hydrogen-enriched natural gas in a swirl burner. The results indicate that the swirl angle θ and swirl length L play an essential role in the combustion of natural gas containing hydrogen. As the swirl angle θ increases the flame temperature decreases more slowly the combustion becomes more stable and the length of the flame is slightly increased. Simultaneously CO and NO emissions will gradually decrease and the combustion effect is enhanced when the swirl angle is 45◦. With increased swirl length L the flame length grows the high-temperature region expands and CO and NO emissions decrease. Meanwhile the change in swirl length has little effect on the increase of flame peak temperature when the fuel is thoroughly mixed. When the swirl length is 12 mm CO and NO emissions are lower and NO emissions are reduced by 36.11% compared to a swirl length of 6 mm. This work is a reference point for applying hydrogen-mixed natural gas in the swirl burner but it must be studied and optimized further in future research.
Improvement of Temperature and Humidity Control of Proton Exchange Membrane Fuel Cells
Sep 2021
Publication
Temperature and humidity are two important interconnected factors in the performance of PEMFCs (Proton Exchange Membrane Fuel Cells). The fuel and oxidant humidity and stack temperature in a fuel cell were analyzed in this study. There are many factors that affect the temperature and humidity of the stack. We adopt the fuzzy control method of multi-input and multi-output to control the temperature and humidity of the stack. A model including a driver vehicle transmission motor air feeding electrical network stack hydrogen supply and cooling system was established to study the fuel cell performance. A fuzzy controller is proven to be better in improving the output power of fuel cells. The three control objectives are the fan speed control for regulating temperature the solenoid valve on/off control of the bubble humidifier for humidity variation and the speed of the pump for regulating temperature difference. In addition the results from the PID controller stack model and the fuzzy controller stack model are compared in this research. The fuel cell bench test has been built to validate the effectiveness of the proposed fuzzy control. The maximum temperature of the stack can be reduced by 5 ◦C with the fuzzy control in this paper so the fuel cell output voltage (power) increases by an average of approximately 5.8%.
Reversible Hydrogenation of AB2-type Zr–Mg–Ni–V Based Hydrogen Storage Alloys
Feb 2021
Publication
The development of hydrogen energy is hindered by the lack of high-efficiency hydrogen storage materials. To explore new high-capacity hydrogen storage alloys reversible hydrogen storage in AB2-type alloy is realized by using A or B-side elemental substitution. The substitution of small atomic-radius element Zr and Mg on A-side of YNi2 and partial substitution of large atomic-radius element V on B-side of YNi2 alloy was investigated in this study. The obtained ZrMgNi4 ZrMgNi3V and ZrMgNi2V2 alloys remained single Laves phase structure at as-annealed hydrogenated and dehydrogenated states indicating that the hydrogen-induced amorphization and disproportionation was eliminated. From ZrMgNi4 to ZrMgNi2V2 with the increase of the degree of vanadium substitution the reversible hydrogen storage capacity increased from 0.6 wt% (0.35H/M) to 1.8 wt% (1.0H/M) meanwhile the lattice stability gradually increased. The ZrMgNi2V2 alloy could absorb 1.8 wt% hydrogen in about 2 h at 300 K under 4 MPa H2 pressure and reversibly desorb the absorbed hydrogen in approximately 30 min at 473 K without complicated activation process. The prominent properties of ZrMgNi2V22 elucidate its high potential for hydrogen storage application.
Temperature Effect on the Mechanical Properties of Liner Materials used for Type IV Hydrogen Storage Tanks
Sep 2021
Publication
Type IV hydrogen storage tanks play an important role in hydrogen fuel cell vehicles (HFCVs) due to their superiority of lightweight good corrosion and fatigue resistance. It is planned to be used between -40℃ and 85℃ at which the polymer liner may have a degradation of mechanical properties and buckling collapse. This demand a good performance of liner materials in that temperature range. In this article the temperature effect on mechanical properties of polyamide 6 (PA6) liner material including specimens with weld seam was investigated via the stress-strain curve (S-S curve) macroscopic and microscopic morphology. Considering that the mechanical properties will change after the liner molding process this test takes samples directly from the liner. Results show that the tensile strength and tensile modulus increased by 2.46 times and 10.6 times respectively with the decrease of temperature especially in the range from 50℃ to -90℃. For the elongation at break and work of fracture they do not monotonously increase with the temperature up. Both of them reduce when the temperature rises from 20°C to 50°C especially for the work of fracture decreasing by 63%. The weld seam weakens the mechanical properties and the elongation at break and work of fracture are more obvious which are greater than 40% at each temperature. In addition the SEM images indicate that the morphology of fracture surface at -90°C is different from that at other temperatures which is a sufficient evidence of toughness reducing in low temperature.
Recent Advances in Hybrid Water Electrolysis for Energy-saving Hydrogen Production
Nov 2022
Publication
Electricity-driven water splitting to convert water into hydrogen (H2) has been widely regarded as an efficient approach for H2 production. Nevertheless the energy conversion efficiency of it is greatly limited due to the disadvantage of the sluggish kinetic of oxidation evolution reaction (OER). To effectively address the issue a novel concept of hybrid water electrolysis has been developed for energy– saving H2 production. This strategy aims to replace the sluggish kinetics of OER by utilizing thermodynamically favorable organics oxidation reaction to replace OER. Herein recent advances in such water splitting system for boosting H2 evolution under low cell voltage are systematically summarized. Some notable progress of different organics oxidation reactions coupled with hydrogen evolution reaction (HER) are discussed in detail. To facilitate the development of hybrid water electrolysis the major challenges and perspectives are also proposed.
Optimized Configuration and Operating Plan for Hydrogen Refueling Station with On-Site Electrolytic Production
Mar 2022
Publication
Hydrogen refueling stations (HRSs) are critical for the popularity of hydrogen vehicles (fuel cell electric vehicles—FCEVs). However due to high installation investment and operating costs the proliferation of HRSs is difficult. This paper studies HRSs with on-site electrolytic production and hydrogen storage devices and proposes an optimization method to minimize the total costs including both installation investment and operating costs (OPT-ISL method). Moreover to acquire the optimization constraints of hydrogen demand this paper creatively develops a refueling behavior simulation method for different kinds of FCEVs and proposes a hydrogen-demand estimation model to forecast the demand with hourly intervals for HRS. The Jensen–Shannon divergence is applied to verify the accuracy of the hydrogen-demand estimation. The result: 0.029 is much smaller than that of the estimation method in reference. Based on the estimation results and peak-valley prices of electricity from the grid a daily hydrogen generation plan is obtained as well as the optimal capacities of electrolyzers and storage devices. As for the whole costs compared with previous configuration methods that only consider investment costs or operating costs the proposed OPT-ISL method has the least 8.1 and 10.5% less respectively. Moreover the proposed OPT-ISL method shortens the break-even time for HRS from 11.1 years to 7.8 years a decrease of 29.7% so that the HRS could recover its costs in less time.
Fuel Cell Power Systems for Maritime Applications: Progress and Perspectives
Jan 2021
Publication
Fuel cells as clean power sources are very attractive for the maritime sector which is committed to sustainability and reducing greenhouse gas and atmospheric pollutant emissions from ships. This paper presents a technological review on fuel cell power systems for maritime applications from the past two decades. The available fuels including hydrogen ammonia renewable methane and methanol for fuel cells under the context of sustainable maritime transportation and their pre-processing technologies are analyzed. Proton exchange membrane molten carbonate and solid oxide fuel cells are found to be the most promising options for maritime applications once energy efficiency power capacity and sensitivity to fuel impurities are considered. The types layouts and characteristics of fuel cell modules are summarized based on the existing applications in particular industrial or residential sectors. The various research and demonstration projects of fuel cell power systems in the maritime industry are reviewed and the challenges with regard to power capacity safety reliability durability operability and costs are analyzed. Currently power capacity costs and lifetime of the fuel cell stack are the primary barriers. Coupling with batteries modularization mass production and optimized operating and control strategies are all important pathways to improve the performance of fuel cell power systems.
Study on the Effect of Second Injection Timing on the Engine Performances of a Gasoline/Hydrogen SI Engine with Split Hydrogen Direct Injecting
Oct 2020
Publication
Split hydrogen direct injection (SHDI) has been proved capable of better efficiency and fewer emissions. Therefore to investigate SHDI deeply a numerical study on the effect of second injection timing was presented at a gasoline/hydrogen spark ignition (SI) engine with SHDI. With an excess air ratio of 1.5 five different second injection timings achieved five kinds of hydrogen mixture distribution (HMD) which was the main factor affecting the engine performances. With SHDI since the HMD is manageable the engine can achieve better efficiency and fewer emissions. When the second injection timing was 105◦ crank angle (CA) before top dead center (BTDC) the Pmax was the highest and the position of the Pmax was the earliest. Compared with the single hydrogen direct injection (HDI) the NOX CO and HC emissions with SHDI were reduced by 20% 40% and 72% respectively.
Numerical Simulation of Hydrogen Leakage from Fuel Cell Vehicle in an Outdoor Parking Garage
Aug 2021
Publication
It is significant to assess the hydrogen safety of fuel cell vehicles (FCVs) in parking garages with a rapidly increased number of FCVs. In the present work a Flame Acceleration Simulator (FLACS) a computational fluid dynamics (CFD) module using finite element calculation was utilized to predict the dispersion process of flammable hydrogen clouds which was performed by hydrogen leakage from a fuel cell vehicle in an outdoor parking garage. The effect of leakage diameter (2 mm 3 mm and 4 mm) and parking configurations (vertical and parallel parking) on the formation of flammable clouds with a range of 4–75% by volume was considered. The emission was assumed to be directed downwards from a Thermally Activated Pressure Relief Device (TPRD) of a 70 MPa storage tank. The results show that the 0.7 m parking space stipulated by the current regulations is less than the safety space of fuel cell vehicles. Compared with a vertical parking configuration it is safer to park FCVs in parallel. It was also shown that release through a large TPRD orifice should be avoided as the proportion of the larger hydrogen concentration in the whole flammable domain is prone to more accidental severe consequences such as overpressure.
Reliability Analysis of Pyrotechnic Igniter for Hydrogen-Oxygen Rocket Engine with Low Temperature Combustion Instability Failure Mode
Mar 2022
Publication
To evaluate the functional reliability of the pyrotechnic igniter in the failure mode of unstable combustion at low temperature a reliability and reliability sensitivity analysis method based on the combination of an interior ballistic model and Kriging reliability method is proposed. Through the deterministic interior ballistic simulation the failure mode of low temperature unstable combustion of the pyrotechnic igniter is examined while the random variables are introduced to establish the ignition nonlinear implicit function of the pyrotechnic igniter. The ignition display function of the pyrotechnic igniter is established by the Kriging model which avoids the repeated calculation of true limit state function values. This study provides an efficient approach to evaluate the ignition reliability of the pyrotechnic igniter and compared with the traditional Monte Carlo method to verify the accuracy of the results. Finally reliability-based sensitivity indices are presented to quantify the significance of random parameters. It is shown that the influence of the uncertainties can be precisely described and the diameter of the nozzle plays a dominant role in ignition reliability. Additionally ignition experiments of nozzles with different diameters were performed to verify the result of sensitivity. This can further support the detailed design of the pyrotechnic igniter
Numerical Simulation of the Transport and the Thermodynamic Properties of Imported Natural Gas Inected with Hydrogen in the Manifold
Nov 2023
Publication
Blending hydrogen with natural gas (NG) is an efficient method for transporting hydrogen on a large scale at a low cost. The manifold at the NG initial station is an important piece of equipment that enables the blending of hydrogen with NG. However there are differences in the components and component contents of imported NG from different countries. The components of hydrogen-blended NG can affect the safety and efficiency of transportation through pipeline systems. Therefore numerical simulations were performed to investigate the blending process and changes in the thermodynamic properties of four imported NGs and hydrogen in the manifold. The higher the heavy hydrocarbon content in the imported NG the longer the distance required for the gas to mix uniformly with hydrogen in the pipeline. Hydrogen blending reduces the temperature and density of NG. The gas composition is the main factor affecting the molar calorific value of a gas mixture and hydrogen blending reduces the molar calorific value of NG. The larger the content of high-molar calorific components in the imported NG the higher the molar calorific value of the gas after hydrogen blending. Increasing both the temperature and hydrogen mixing ratio reduces the Joule-Thomson coefficient of the hydrogen-blended NG. The results of this study provide technical references for the transport of hydrogen-blended NG.
Optimization of Emergency Alternatives for Hydrogen Leakage and Explosion Accidents Based on Improved VIKOR
Nov 2023
Publication
Hydrogen leakage and explosion accidents have obvious dangers ambiguity of accident information and urgency of decision-making time. These characteristics bring challenges to the optimization of emergency alternatives for such accidents. Effective emergency decision making is crucial to mitigating the consequences of accidents and minimizing losses and can provide a vital reference for emergency management in the field of hydrogen energy. An improved VIKOR emergency alternatives optimization method is proposed based on the combination of hesitant triangular fuzzy set (HTFS) and the cumulative prospect theory (CPT) termed the HTFS-CPT-VIKOR method. This method adopts the hesitant triangular fuzzy number to represent the decision information on the alternatives under the influence of multi-attributes constructs alternatives evaluation indicators and solves the indicator weights by using the deviation method. Based on CPT positive and negative ideal points were used as reference points to construct the prospect matrix which then utilized the VIKOR method to optimize the emergency alternatives for hydrogen leakage and explosion accidents. Taking an accident at a hydrogen refueling station as an example the effectiveness and rationality of the HTFS-CPT-VIKOR method were verified by comparing with the existing three methods and conducting parameter sensitivity analysis. Research results show that the HTFS-CPT-VIKOR method effectively captures the limited psychological behavior characteristics of decision makers and enhances their ability to identify filter and judge ambiguous information making the decisionmaking alternatives more in line with the actual environment which provided strong support for the optimization of emergency alternatives for hydrogen leakage and explosion accidents.
Economic Analysis of a Photovoltaic Hydrogen Refueling Station Based on Hydrogen Load
Sep 2023
Publication
With the goal of achieving “carbon peak in 2030 and carbon neutrality in 2060” as clearly proposed by China the transportation sector will face long–term pressure on carbon emissions and the application of hydrogen fuel cell vehicles will usher in a rapid growth period. However true “zero carbon” emissions cannot be separated from “green hydrogen”. Therefore it is of practical significance to explore the feasibility of renewable energy hydrogen production in the context of hydrogen refueling stations especially photovoltaic hydrogen production which is applied to hydrogen refueling stations (hereinafter referred to “photovoltaic hydrogen refueling stations”). This paper takes a hydrogen refueling station in Shanghai with a supply capacity of 500 kg/day as the research object. Based on a characteristic analysis of the hydrogen demand of the hydrogen refueling station throughout the day this paper studies and analyzes the system configuration operation strategy environmental effects and economics of the photovoltaic hydrogen refueling station. It is estimated that when the hydrogen price is no less than 6.23 USD the photovoltaic hydrogen refueling station has good economic benefits. Additionally compared with the conventional hydrogen refueling station it can reduce carbon emissions by approximately 1237.28 tons per year with good environmental benefits.
Alternative-energy-vehicles Deployment Delivers Climate, Air Quality, and Health Co-benefits when Coupled with Decarbonizing Power Generation in China
Aug 2021
Publication
China is the world’s largest carbon emitter and suffers from severe air pollution which results in approximately one million premature deaths/year. Alternative energy vehicles (AEVs) (electric hydrogen fuel cell and natural gas vehicles) can reduce carbon emissions and improve air quality. However climate air quality and health benefits of AEVs powered with deeply decarbonized power generation are poorly quantified. Here we quantitatively estimate the air quality health carbon emission and economic benefits of replacing internal combustion engine vehicles with various AEVs. We find co-benefits increase dramatically as the electricity grid decarbonizes and hydrogen is produced from non-fossil fuels. Relative to 2015 a conversion to AEVs using largely non-fossil power can reduce air pollution and associated premature mortalities and years of life lost by 329000 persons/year and 1611000 life years/year. Thus maximizing climate air quality and health benefits of AEV deployment in China requires rapid decarbonization of the power system.
Performance Study on Methanol Steam Reforming Rib Micro-Reactor with Waste Heat Recovery
Mar 2020
Publication
Automobile exhaust heat recovery is considered to be an effective means to enhance fuel utilization. The catalytic production of hydrogen by methanol steam reforming is an attractive option for onboard mobile applications due to its many advantages. However the reformers of conventional packed bed type suffer from axial temperature gradients and cold spots resulting from severe limitations of mass and heat transfer. These disadvantages limit reformers to a low efficiency of catalyst utilization. A novel rib microreactor was designed for the hydrogen production from methanol steam reforming heated by automobile exhaust and the effect of inlet exhaust and methanol steam on reactor performance was numerically analyzed in detail with computational fluid dynamics. The results showed that the best operating parameters were the counter flow water-to-alcohol (W/A) of 1.3 exhaust inlet velocity of 1.1 m/s and exhaust inlet temperature of 773 K when the inlet velocity and inlet temperature of the reactant were 0.1 m/s and 493 K respectively. At this condition a methanol conversion of 99.4% and thermal efficiency of 28% were achieved together with a hydrogen content of 69.6%.
Evaluation of Stability and Catalytic Activity of Ni Catalysts for Hydrogen Production by Biomass Gasification in Supercritical Water
Mar 2019
Publication
Supercritical water gasification is a promising technology for wet biomass utilization. In this paper Ni and other metal catalysts were synthesized by wet impregnation. The stability and catalytic activities of Ni catalysts were evaluated. Firstly catalytic activities of Ni Fe Cu catalysts supported on MgO were tested using wheat straw as raw material in a batch reactor at 723 K and water density of 0.07 cm3/g. Experimental results showed that the order of metal catalyst activity for hydrogen generation was Ni/MgO > Fe/MgO > Cu/MgO. Secondly the influence of different supports on Ni catalysts performance was investigated. The results showed that the order of the Ni catalysts’ activity with different supports was Ni/MgO > Ni/ZnO > Ni/Al2O3 > Ni/ZrO2. Finally the effects of Ni loading and the amount of Ni catalyst addition on hydrogen production and the stability of Ni/MgO catalyst were studied. It was found that serious deactivation of Ni catalyst in the process of supercritical water gasification took place. Even if carbon deposited on the catalyst surface was removed by high temperature calcination and the catalyst was reduced with hydrogen the activity of used catalyst was only partially restored.
A Novel Remaining Useful Life Prediction Method for Hydrogen Fuel Cells Based on the Gated Recurrent Unit Neural Network
Jan 2022
Publication
The remaining useful life (RUL) prediction for hydrogen fuel cells is an important part of its prognostics and health management (PHM). Artificial neural networks (ANNs) are proven to be very effective in RUL prediction as they do not need to understand the failure mechanisms behind hydrogen fuel cells. A novel RUL prediction method for hydrogen fuel cells based on the gated recurrent unit ANN is proposed in this paper. Firstly the data were preprocessed to remove outliers and noises. Secondly the performance of different neural networks is compared including the back propagation neural network (BPNN) the long short-term memory (LSTM) network and the gated recurrent unit (GRU) network. According to our proposed method based on GRU the root mean square error was 0.0026 the mean absolute percentage error was 0.0038 and the coefficient of determination was 0.9891 for the data from the challenge datasets provided by FCLAB Research Federation when the prediction starting point was 650 h. Compared with the other RUL prediction methods based on the BPNN and the LSTM our prediction method is better in both prediction accuracy and convergence rate.
Fundamentals, Materials, and Machine Learning of Polymer Electrolyte Membrane Fuel Cell Technology
Jun 2020
Publication
Polymer electrolyte membrane (PEM) fuel cells are electrochemical devices that directly convert the chemical energy stored in fuel into electrical energy with a practical conversion efficiency as high as 65%. In the past years significant progress has been made in PEM fuel cell commercialization. By 2019 there were over 19000 fuel cell electric vehicles (FCEV) and 340 hydrogen refueling stations (HRF) in the U.S. (~8000 and 44 respectively) Japan (~3600 and 112 respectively) South Korea (~5000 and 34 respectively) Europe (~2500 and 140 respectively) and China (~110 and 12 respectively). Japan South Korea and China plan to build approximately 3000 HRF stations by 2030. In 2019 Hyundai Nexo and Toyota Mirai accounted for approximately 63% and 32% of the total sales with a driving range of 380 and 312 miles and a mile per gallon (MPGe) of 65 and 67 respectively. Fundamentals of PEM fuel cells play a crucial role in the technological advancement to improve fuel cell performance/durability and reduce cost. Several key aspects for fuel cell design operational control and material development such as durability electrocatalyst materials water and thermal management dynamic operation and cold start are briefly explained in this work. Machine learning and artificial intelligence (AI) have received increasing attention in material/energy development. This review also discusses their applications and potential in the development of fundamental knowledge and correlations material selection and improvement cell design and optimization system control power management and monitoring of operation health for PEM fuel cells along with main physics in PEM fuel cells for physics-informed machine learning. The objective of this review is three fold: (1) to present the most recent status of PEM fuel cell applications in the portable stationary and transportation sectors; (2) to describe the important fundamentals for the further advancement of fuel cell technology in terms of design and control optimization cost reduction and durability improvement; and (3) to explain machine learning physics-informed deep learning and AI methods and describe their significant potentials in PEM fuel cell research and development (R&D).
Thermodynamic Analysis of Solid Oxide Electrolyzer Integration with Engine Waste Heat Recovery for Hydrogen Production
Jul 2021
Publication
Water electrolysis based on solid oxide electrolysis cell (SOEC) exhibits high conversion efficiency due to part of energy demand can be derived from thermal energy. Therefore it can be integrated with other sources of thermal energy to reduce the consumption of electrical energy. In this paper a diesel engine is integrated with the SOEC stacks for heat recovery steam generator (HRSG). The thermal energy from the engine exhaust gas used to heat the inlet H2O of the SOEC is carried out as the integration case. A SOEC plant using electricity as the thermal heat input is selected as the base case. Thermodynamic analysis of the benchmark and integration scheme reveals that an electrical efficiency of 73.12% and 85.17% can be achieved respectively. The diesel to power efficiency can be increased to 70% when the exhaust gas is completely utilized by the SOEC system. The impacts of some key parameters including current density and operating temperature on system performance have also been conducted and found that the system has optimized parameters of current density and operating temperature to achieve better performance.
Numerical Study of Combustion and Emission Characteristics for Hydrogen Mixed Fuel in the Methane-Fueled Gas Turbine Combustor
Jan 2023
Publication
The aeroderivative gas turbine is widely used as it demonstrates many advantages. Adding hydrogen to natural gas fuels can improve the performance of combustion. Following this the effects of hydrogen enrichment on combustion characteristics were analyzed in an aeroderivative gas turbine combustor using CFD simulations. The numerical model was validated with experimental results. The conditions of the constant mass flow rate and the constant energy input were studied. The results indicate that adding hydrogen reduced the fuel residues significantly (fuel mass at the combustion chamber outlet was reduced up to 60.9%). In addition the discharge of C2H2 and other pollutants was reduced. Increasing the volume fraction of hydrogen in the fuel also reduced CO emissions at the constant energy input while increasing CO emissions at the constant fuel mass flow rate. An excess in the volume fraction of added hydrogen changed the combustion mode in the combustion chamber resulting in fuel-rich combustion (at constant mass flow rate) and diffusion combustion (at constant input power). Hydrogen addition increased the pattern factor and NOx emissions at the outlet of the combustion chamber.
Hydrogen Refueling Stations and Carbon Emission Reduction of Coastal Expressways: A Deployment Model and Multi-Scenario Analysis
Jul 2022
Publication
Hydrogen is considered to the ultimate solution to achieve carbon emission reduction due to its wide sources and high calorific value as well as non-polluting renewable and storable advantages. This paper starts from the coastal areas uses offshore wind power hydrogen production as the hydrogen source and focuses on the combination of hydrogen supply chain network design and hydrogen expressway hydrogen refueling station layout optimization. It proposes a comprehensive mathematical model of hydrogen supply chain network based on cost analysis which determined the optimal size and location of hydrogen refueling stations on hydrogen expressways in coastal areas. Under the multi-scenario and multi-case optimization results the location of the hydrogen refueling station can effectively cover the road sections of each case and the unit hydrogen cost of the hydrogen supply chain network is between 11.8 and 15.0 USD/kgH2 . Meanwhile it was found that the transportation distance and the number of hydrogen sources play a decisive role on the cost of hydrogen in the supply chain network and the location of hydrogen sources have a decisive influence on the location of hydrogen refueling stations. In addition carbon emission reduction results of hydrogen supply chain network show that the carbon emission reduction per unit hydrogen production is 15.51 kgCO2/kgH2 at the production side. The CO2 emission can be reduced by 68.3 kgCO2/km and 6.35 kgCO2/kgH2 per unit mileage and per unit hydrogen demand at the application side respectively. The layout planning utilization of hydrogen energy expressway has a positive impact on energy saving and emission reduction.
Velocity Measurements of Hydrogen Jets Using the Optical Flow Method
Sep 2021
Publication
Concentration and velocity measurements are crucial for developing and validating hydrogen jet models which provide scientific bases for hydrogen safety analyses. The concentration fields have been visualized and accurately measured using laser diagnostic methods based on lase Rayleigh and Raman scattering techniques. However the velocity measurements are more challenging. Particle image velocimetry (PIV) has been commonly used for measuring velocities in turbulent flows by seeding tracer particles into the flow and assuming the particles intimately following the flow. However sometimes the particle seeding is difficult or disturbs the flow. Moreover simultaneously concentration and velocity measurements are very difficult when using PIV systems to measure the velocities. Therefore the optical flow velocimetry (OFV) method was used to resolve the velocity fields from the scalar fields or particle images of hydrogen jets. In the present work the velocity field and particle images of hydrogen jets were simulated using FLUENT with the large eddy simulation (LES) model and the particle images were then used to resolve the velocity field by the OFV method. The OFV results were compared with the CFD simulations to verify their accuracy. The results show that the OFC method was an efficient low-cost way to extract the velocity fields from particle images. The OFV method accurately located the large vortices in the flow and the velocity distribution of the high-velocity gradients regions was consistent with the CFD results. The present study lays a foundation for using the OFV method to directly resolve the velocity fields from the concentration fields of hydrogen jets measured by laser diagnostics.
Integrating a Top-Gas Recycling and CO2 Electrolysis Process for H2-Rich Gas Injection and Reduce CO2 Emissions from an Ironmaking Blast Furnace
Mar 2022
Publication
Introducing CO2 electrochemical conversion technology to the iron-making blast furnace not only reduces CO2 emissions but also produces H2 as a byproduct that can be used as an auxiliary reductant to further decrease carbon consumption and emissions. With adequate H2 supply to the blast furnace the injection of H2 is limited because of the disadvantageous thermodynamic characteristics of the H2 reduction reaction in the blast furnace. This paper presents thermodynamic analysis of H2 behaviour at different stages with the thermal requirement consideration of an iron-making blast furnace. The effect of injecting CO2 lean top gas and CO2 conversion products H2–CO gas through the raceway and/or shaft tuyeres are investigated under different operating conditions. H2 utilisation efficiency and corresponding injection volume are studied by considering different reduction stages. The relationship between H2 injection and coke rate is established. Injecting 7.9–10.9 m3/tHM of H2 saved 1 kg/tHM coke rate depending on injection position. Compared with the traditional blast furnace injecting 80 m3/tHM of H2 with a medium oxygen enrichment rate (9%) and integrating CO2 capture and conversion reduces CO2 emissions from 534 to 278 m3/tHM. However increasing the hydrogen injection amount causes this iron-making process to consume more energy than a traditional blast furnace does.
Safety Analysis and Risk Control of Shore-Based Bunkering Operations for Hydrogen Powered Ships
Sep 2021
Publication
In order to ensure the safety of shore-based hydrogen bunkering operations this paper takes a 2000-ton bulk hydrogen powered ship as an example. Firstly the HAZID method is used to identify the hazards of hydrogen bunkering then the probability of each scenario is analyzed and then the consequences of scenarios with high risk based on FLACS software is simulated. Finally the personal risk of bunkering operation is evaluated and the bunkering restriction area is defined. The results show that the personal risk of shore-based bunkering operation of hydrogen powered ship is acceptable but the following risk control measures should be taken: (1) The bunkering restriction area shall be delineated and only the necessary operators are allowed to enter the area and control the any form of potential ignition source; (2) The hose is the high risk hazards during bunkering. The design form of bunkering arm and bunkering hose is considered to shorten the length of the hose as far as possible; (3) A safe distance between shore-based hydrogenation station and the building outside the station should be guaranteed. The results have a guiding role in effectively reducing the risk of hydrogen bunkering operation.
Optimization of Energy Management Strategy for Fuel Cell Hybrid Electric Vehicles Based on Dynamic Programming
Jun 2022
Publication
Fuel cell hybrid electric vehicles have attracted a large amount of attention in recent years owing to their advantages of zero emissions high efficiency and low noise. To improve the fuel economy and system durability of vehicles this paper proposes an energy management strategy optimization method for fuel cell hybrid electric vehicles based on dynamic programming. Rule-based and dynamic-programming-based strategies are developed based on building a fuel cell/battery hybrid system model. The rule-based strategy is improved with a power distribution scheme of dynamic programming strategy to improve the fuel economy of the vehicle. Furthermore a limit on the rate of change of the output power of the fuel cell system is added to the rule-based strategy to avoid large load changes to improve the durability of the fuel cell. The simulation results show that the equivalent 100 km hydrogen consumption of the strategy based on the dynamic programming optimization rules is reduced by 6.46% compared with that before the improvement and by limiting the rate of change of the output power of the fuel cell system the times of large load changes are reduced. Therefore the strategy based on the dynamic programming optimization rules effectively improves the fuel economy and system durability of vehicles.
Design and Optimization of Coal to Hydrogen System Coupled with Non-Nominal Operation of Thermal Power Unit
Dec 2022
Publication
In an actual thermal power plant deep peak shaving will cause thermal power units to run under non-nominal conditions for an extended period resulting in serious problems such as increased equipment wearing low equipment utilization efficiency and decreased benefits. To this end in this work both the design and optimization method for a coal to hydrogen system which is coupled with the expected non-nominal operation of thermal power units are proposed. Aiming towards maximum profit in the context of thermal power plants a mathematical optimization model for a coal to hydrogen system based on the multi-period operating conditions of thermal power plants is established. The corresponding optimal design scheme of the coal to hydrogen system is determined using variable operating conditions. The superiority of the integrated system compared with an independent system is explored and the feasibility of the proposed method is verified by using the case study of an actual thermal power plant. The results show that compared with the independent system the economic benefits of the integrated system can increase by 13.56% where the sale of hydrogen in the coal to hydrogen system accounts for 60.3% of the total benefit. The main expenditure associated with the system is the purchase cost of feedstock coal accounting for 91.8%. Since the required power and medium-pressure steam in the coal to hydrogen process are provided by thermal power units the minimum operating load of the thermal power plant in the integrated system increases from 40% to 60.1% which significantly improves the utilization efficiency and service life of the generator units. In addition the proposed integration scheme of the system is simple and controllable which can contribute to the maintenance of the safe and stable operation of power generation and hydrogen production processes. These results are expected to provide the necessary methodological guidance for the integration and optimization of coal-fired power plants and coal to hydrogen systems.
Influence of Air Distribution on Combustion Characteristics of a Micro Gas Turbine Fuelled by Hydrogen-doped Methane
Nov 2021
Publication
Adding hydrogen to the fuel can change the combustion characteristics and greatly improve the pollutants emission for the gas turbine. The numerical method was adopted to study the combustion process in a counter-flow combustor of a 100 kW micro gas turbine using methane doped by hydrogen and various distribution schemes of air flow. The combustion characteristics and pollutant emissions were explored to ascertain the influence of air distribution based on solving the validated models. It was shown that as the amount of premixed air increased in the swirling gas the range of the recirculation region became larger and the range of the high-temperature zone in the combustion chamber gradually enlarged. When the amount of premixed air was 30% the outlet temperature distribution of the combustor was excellent and the average temperature was 1172 K. Moreover the concentration of NOX gradually increased and reached a maximum value of 23.46 ppm (@15% O2) as the premixed air increased in the range of the ratio less than 40%. It was reduced to 0.717 ppm (@15% O2) when the amount of premixed air increased to 50%. These findings may support the running of the micro gas turbine using the hybrid fuel of hydrogen and methane.
Hydrogen Storage by Liquid Hydrogen Carriers: Catalyst, Renewable Carrier, and Technology - A Review
Mar 2023
Publication
Hydrogen has attracted widespread attention as a carbon-neutral energy source but developing efficient and safe hydrogen storage technologies remains a huge challenge. Recently liquid organic hydrogen carriers (LOHCs) technology has shown great potential for efficient and stable hydrogen storage and transport. This technology allows for safe and economical large-scale transoceanic transportation and long-cycle hydrogen storage. In particular traditional organic hydrogen storage liquids are derived from nonrenewable fossil fuels through costly refining procedures resulting in unavoidable environmental contamination. Biomass holds great promise for the preparation of LOHCs due to its unique carbon-balance properties and feasibility to manufacture aromatic and nitrogen-doped compounds. According to recent studies almost 100% conversion and 92% yield of benzene could be obtained through advanced biomass conversion technologies showing great potential in preparing biomass-based LOHCs. Overall the present LOHCs systems and their unique applications are introduced in this review and the technical paths are summarized. Furthermore this paper provides an outlook on the future development of LOHCs technology focusing on biomass-derived aromatic and N-doped compounds and their applications in hydrogen storage.
Residual Tensile Properties of Carbon Fiber Reinforced Epoxy Resin Composites at Elevated Temperatures
Sep 2021
Publication
Carbon fiber reinforced epoxy resin composites have attracted great attention in high pressure hydrogen storage for its light weight and excellent mechanical properties. The degradation of residual mechanical properties at elevated temperature from 20 °C to 450 °C were studied experimentally. The effects of temperature on the tensile strength and failure mode of the composite specimens with stacking sequences of 0° 90° and ±45° (labeled as CF0 CF90 and CF 45) were systematically analyzed followed by the fracture surfaces examination. Results show that the tensile strength residual ratios of the three kinds of specimens decrease significantly with heating temperature increasing. In particular the decomposing temperature of the resin matrix exerts the largest effects on the degradation of tensile strength of CF0 specimen within 450 °C. While the loss of tensile strength of CF90 and CF45 specimens is dependent on the thermal softening of epoxy resin which has closely related to the glass transition temperature. Furthermore the debonding and fiber softening appeared in the CF0 specimens when the temperature reached 450 °C. For CF90 specimens the degradation of bonding strength of epoxy could be found at 150 °C and regarding CF45 specimens delamination cracking between plies occurred extensively when the temperature above 125 °C.
A Numerical Investigation on De-NOx Technology and Abnormal Combustion Control for a Hydrogen Engine with EGR System
Sep 2020
Publication
The combustion emissions of the hydrogen-fueled engines are very clean but the problems of abnormal combustion and high NOx emissions limit their applications. Nowadays hydrogen engines use exhaust gas recirculation (EGR) technology to control the intensity of premixed combustion and reduce the NOx emissions. This study aims at improving the abnormal combustion and decreasing the NOx emissions of the hydrogen engine by applying a three-dimensional (3D) computational fluid dynamics (CFD) model of a single-cylinder hydrogen-fueled engine equipped with an EGR system. The results indicated that peak in-cylinder pressure continuously increased with the increase of the ignition advance angle and was closer to the top dead center (TDC). In addition the mixture was burned violently near the theoretical air–fuel ratio and the combustion duration was shortened. Moreover the NOx emissions the average pressure and the in-cylinder temperature decreased as the EGR ratio increased. Furthermore increasing the EGR ratio led to an increase in the combustion duration and a decrease in the peak heat release rate. EGR system could delay the spontaneous combustion reaction of the end-gas and reduce the probability of knocking. The pressure rise rate was controlled and the in-cylinder hot spots were reduced by the EGR system which could suppress the occurrence of the pre-ignition in the hydrogen engine.
Research on High-Pressure Hydrogen Pre-Cooling Based on CFD Technology in Fast Filling Process
Dec 2021
Publication
In the fast filling process in order to control the temperature of the vehicle-mounted storage tank not to exceed the upper limit of 85 ◦C it is an effective method to add a hydrogen pre-cooling system upstream of the hydrogenation machine. In this paper Fluent is used to simulate the heat transfer process of high-pressure hydrogen in a shell-and-tube heat exchanger and the phase change process of refrigerant R23. The accuracy of the model is proven by a comparison with the data in the references. Using this model the temperature field and gas volume fraction in the heat transfer process are obtained which is helpful to analyze the heat transfer mechanism. At the same time the influence of hydrogen inlet temperature hydrogen inlet pressure and refrigerant flow rate on the refrigeration performance was studied. The current work shows that the model can be used to determine the best working parameters in the pre-cooling process and reduce the operating cost of the hydrogen refueling station.
Effect of H2 on Blast Furnace Ironmaking: A Review
Nov 2022
Publication
Under the background of “carbon peaking” and “carbon neutralization” the green transformation of iron and steel enterprises is imminent. The hydrogen-rich smelting technology of blast furnaces is very important for reducing energy consumption and CO2 emission in ironmaking systems and it is one of the important directions of green and low-carbon development of iron and steel enterprises. In this paper the research status of the thermal state reduction mechanism of iron-bearing burden coke degradation behavior and formation of the cohesive zone in various areas of blast furnace after hydrogen-rich smelting is summarized which can make a more clear and comprehensive understanding for the effect of H2 on blast furnace ironmaking. Meanwhile based on the current research situation it is proposed that the following aspects should be further studied in the hydrogen-rich smelting of blast furnaces: (1) the utilization rate of hydrogen and degree of substitution for direct reduction (2) combustion behavior of fuel in raceway (3) control of gas flow distribution in the blast furnace (4) operation optimization of the blast furnace.
Progress of Performance, Emission, and Technical Measures of Hydrogen Fuel Internal-Combustion Engines
Oct 2022
Publication
To achieve the goals of low carbon emission and carbon neutrality some urgent challenges include the development and utilization of low-carbon or zero-carbon internal combustion engine fuels. Hydrogen as a clean efficient and sustainable fuel has the potential to meet the abovementioned challenges. Thereby hydrogen internal combustion engines have been attracting attention because of their zero carbon emissions high thermal efficiency high reliability and low cost. In this paper the opportunities and challenges faced by hydrogen internal-combustion engines were analyzed. The progress of hydrogen internal-combustion engines on the mixture formation combustion mode emission reduction knock formation mechanism and knock suppression measures were summarized. Moreover possible technical measures for hydrogen internal-combustion engines to achieve higher efficiency and lower emissions were suggested.
Contribution of Potential Clean Trucks in Carbon Peak Pathway of Road Freight Based on Scenario Analysis: A Case Study of China
Oct 2022
Publication
Reducing the carbon emissions from trucks is critical to achieving the carbon peak of road freight. Based on the prediction of truck population and well-to-wheel (WTW) emission analysis of traditional diesel trucks and potential clean trucks including natural gas battery-electric plug-in hybrid electric and hydrogen fuel cell the paper analyzed the total greenhouse gas (GHG) emissions of China's road freight under four scenarios including baseline policy facilitation (PF) technology breakthrough (TB) and PF-TB. The truck population from 2021 to 2035 is predicted based on regression analysis by selecting the data from 2002 to 2020 of the main variables such as the GDP scale road freight turnover road freight volume and the number of trucks. The study forecasts the truck population of different segments such as mini-duty trucks (MiDT) light-duty trucks (LDT) medium-duty trucks (MDT) and heavy-duty trucks (HDT). Relevant WTW emissions data are collected and adopted based on the popular truck in China's market PHEVs have better emission intensity especially in the HDT field which reduces by 51% compared with ICEVs. Results show that the scenario of TB and PF-TB can reach the carbon peak with 0.13% and 1.5% total GHG emissions reduction per year. In contrast the baseline and PF scenario fail the carbon peak due to only focusing on the number of clean trucks while lacking the restrictions on the GHG emission factors of energy and ignoring the improvement of trucks' energy efficiency and the total emissions increased by 29.76% and 16.69% respectively compared with 2020. As the insights adopting clean trucks has an important but limited effect which should coordinate with the transition to low carbon energy and the melioration of clean trucks to reach the carbon peak of road freight in China.
Transient Modeling and Performance Analysis of Hydrogen-Fueled Aero Engines
Jan 2023
Publication
With the combustor burning hydrogen as well as the strongly coupled fuel and cooling system the configuration of a hydrogen-fueled aero engine is more complex than that of a conventional aero engine. The performance and especially the dynamic behavior of a hydrogen-fueled aero engine need to be fully understood for engine system design and optimization. In this paper both the transient modeling and performance analysis of hydrogen-fueled engines are presented. Firstly the models specific to the hydrogen-fueled engine components and systems including the hydrogen-fueled combustor the steam injection system a simplified model for a quick NOx emission assessment and the heat exchangers are developed and then integrated to a conventional engine models. The simulations with both Simulink and Speedgoat-based hardware in the loop system are carried out. Secondly the performance analysis is performed for a typical turbofan engine configuration CF6 and for the two hydrogen-fueled engine configurations ENABLEH2 and HySIITE which are currently under research and development by the European Union and Pratt & Whitney respectively. At last the simulation results demonstrate that the developed transient models can effectively reflect the characteristics of hydrogen burning heat exchanging and NOx emission for hydrogen-fueled engines. In most cases the hydrogen-fueled engines show lower specific fuel consumption lower turbine entry temperature and less NOx emissions compared with conventional engines. For example at max thrust state the advanced hydrogen-fueled engine can reduce the parameters mentioned above by about 68.5% 3.7% and 12.7% respectively (a mean value of two configurations).
Research on Motor Rotor Loss of High-Speed Air Compressor in the Application of Hydrogen Fuel Cell Vehicle
Feb 2023
Publication
As an important component of hydrogen fuel cell vehicles the air compressor with an air foil bearing rotates at tens of thousands of revolutions per minute. The heat generation concentration problem caused by the high-speed motor loss seriously affects the safe and normal operation of the motor so it is very important to clarify the loss distribution of the high-speed motor and adopt a targeted loss reduction design for air compressor heat dissipation. In this paper for an air compressor with a foil bearing with a rated speed of 80000 rpm an empirical formula and a three-dimensional transient magnetic field finite element model are used to model and calculate the air friction loss stator core loss winding loss and permanent magnet eddy current loss. The accuracy of the analytical calculation method is verified by torque test experiments under different revolutions and the average simulation accuracy can reach 91.1%. Then the distribution of the air friction loss stator core loss winding loss and eddy current loss of the air compressor motor at different revolutions is obtained by using this method. The results show that the proposed method can effectively calculate the motor rotor loss of a high-speed air compressor with air foil bearing. Although the motor efficiency increases with the increase in motor speed the absolute value of loss also increases with the increase in motor speed. Stator core loss and air friction loss are the main sources of loss accounting for 55.64% and 29% of the total motor loss respectively. The electromagnetic loss of winding the eddy current and other alloys account for a relatively small proportion which is 15% in total. The conclusions obtained in this paper can effectively guide calculations of motor loss the motor heat dissipation design of a high-speed air compressor with an air foil bearing.
Techno-Economic Analysis of Hydrogen Storage Technologies for Railway Engineering: A Review
Sep 2022
Publication
According to the specific requirements of railway engineering a techno-economic comparison for onboard hydrogen storage technologies is conducted to discuss their feasibility and potentials for hydrogen-powered hybrid trains. Physical storage methods including compressed hydrogen (CH2 ) liquid hydrogen (LH2 ) and cryo-compressed hydrogen (CcH2 ) and material-based (chemical) storage methods such as ammonia liquid organic hydrogen carriages (LOHCs) and metal hydrides are carefully discussed in terms of their operational conditions energy capacity and economic costs. CH2 technology is the most mature now but its storage density cannot reach the final target which is the same problem for intermetallic compounds. In contrast LH2 CcH2 and complex hydrides are attractive for their high storage density. Nevertheless the harsh working conditions of complex hydrides hinder their vehicular application. Ammonia has advantages in energy capacity utilisation efficiency and cost especially being directly utilised by fuel cells. LOHCs are now considered as a potential candidate for hydrogen transport. Simplifying the dehydrogenation process is the important prerequisite for its vehicular employment. Recently increasing novel hydrogen-powered trains based on different hydrogen storage routes are being tested and optimised across the world. It can be forecasted that hydrogen energy will be a significant booster to railway decarbonisation.
Optimal Planning of Hybrid Electricity–Hydrogen Energy Storage System Considering Demand Response
Mar 2023
Publication
In recent years the stability of the distribution network has declined due to the large proportion of the uses of distributed generation (DG) with the continuous development of renewable energy power generation technology. Meanwhile the traditional distribution network operation mode cannot keep the balance of the source and load. The operation mode of the active distribution network (ADN) can effectively reduce the decline in operation stability caused by the high proportion of DG. Therefore this work proposes a bi-layer model for the planning of the electricity–hydrogen hybrid energy storage system (ESS) considering demand response (DR) for ADN. The upper layer takes the minimum load fluctuation maximum user purchase cost satisfaction and user comfort as the goals. Based on the electricity price elasticity matrix model the optimal electricity price formulation strategy is obtained for the lower ESS planning. In the lower layer the optimal ESS planning scheme is obtained with the minimum life cycle cost (LCC) of ESS the voltage fluctuation of ADN and the load fluctuation as the objectives. Finally the MOPSO algorithm is used to test the model and the correctness of the proposed method is verified by the extended IEEE-33 node test system. The simulation results show that the fluctuation in the voltage and load is reduced by 62.13% and 37.06% respectively.
A Review on Environmental Efficiency Evaluation of New Energy Vehicles Using Life Cycle Analysis
Mar 2022
Publication
New energy vehicles (NEVs) especially electric vehicles (EVs) address the important task of reducing the greenhouse effect. It is particularly important to measure the environmental efficiency of new energy vehicles and the life cycle analysis (LCA) model provides a comprehensive evaluation method of environmental efficiency. To provide researchers with knowledge regarding the research trends of LCA in NEVs a total of 282 related studies were counted from the Web of Science database and analyzed regarding their research contents research preferences and research trends. The conclusion drawn from this research is that the stages of energy resource extraction and collection carrier production and energy transportation maintenance and replacement are not considered to be research links. The stages of material equipment and car transportation and operation equipment settling and forms of use need to be considered in future research. Hydrogen fuel cell electric vehicles (HFCEVs) vehicle type classification the water footprint battery recovery and reuse and battery aging are the focus of further research and comprehensive evaluation combined with more evaluation methods is the direction needed for the optimization of LCA. According to the results of this study regarding EV and hybrid power vehicles (including plug-in hybrid electric vehicles (PHEV) fuel-cell electric vehicles (FCEV) hybrid electric vehicles (HEV) and extended range electric vehicles (EREV)) well-to-wheel (WTW) average carbon dioxide (CO2 ) emissions have been less than those in the same period of gasoline internal combustion engine vehicles (GICEV). However EV and hybrid electric vehicle production CO2 emissions have been greater than those during the same period of GICEV and the total CO2 emissions of EV have been less than during the same period of GICEV.
Exergy Estimate of a Novel Hybrid Solar-gas Power and Organic Rankine Cycle-based Hydrogen-production System
Mar 2022
Publication
This study proposes a novel hybrid solar-gas power and hydrogen-production system which is comprised by the solar tower thermal system gas-steam turbine combined cycle and organic Rankine cycle-based hydrogen-production system. Based on the Ebsilon code the operation processes of the hybrid system are simulated. The results show that the output power and electric efficiency of the hybrid system are 103.9 MW and 41.3% and the daily hydrogen output is 62.2 kg. The operation simulation results of the hybrid system reveal that the gas-steam combined cycle and solar island can both achieve stable operations and the power generation section and hydrogen-production device can both work effectively which means the hybrid system is technically feasible. The exergy estimate results of the hybrid system show that the combustion chamber and solar receiver have the two largest exergy destructions which are 56.5 MW and 45.3 MW. That means the performances of the two components can be further improved. For the hydrogen-production system the exergy destructions of the proton exchange membrane electrolyzer turbine condenser and evaporator of the organic Rankine cycle are 0.156 MW 0.111 MW 2.338 MW and 1.891 MW and the corresponding exergy efficiencies are 51.2% 92.6% 80.7% and 79.5% respectively.
The Role of New Energy in Carbon Neutral
Mar 2021
Publication
Carbon dioxide is an important medium of the global carbon cycle and has the dual properties of realizing the conversion of organic matter in the ecosystem and causing the greenhouse effect. The fixed or available carbon dioxide in the atmosphere is defined as “gray carbon” while the carbon dioxide that cannot be fixed or used and remains in the atmosphere is called “black carbon”. Carbon neutral is the consensus of human development but its implementation still faces many challenges in politics resources technology market and energy structure etc. It is proposed that carbon replacement carbon emission reduction carbon sequestration and carbon cycle are the four main approaches to achieve carbon neutral among which carbon replacement is the backbone. New energy has become the leading role of the third energy conversion and will dominate carbon neutral in the future. Nowadays solar energy wind energy hydropower nuclear energy and hydrogen energy are the main forces of new energy helping the power sector to achieve low carbon emissions. “Green hydrogen” is the reserve force of new energy helping further reduce carbon emissions in industrial and transportation fields. Artificial carbon conversion technology is a bridge connecting new energy and fossil energy effectively reducing the carbon emissions of fossil energy. It is predicted that the peak value of China’s carbon dioxide emissions will reach 110108 t in 2030. The study predicts that China's carbon emissions will drop to 22108 t 33108 t and 44108 t respectively in 2060 according to three scenarios of high medium and low levels. To realize carbon neutral in China seven implementation suggestions have been put forward to build a new “three small and one large” energy structure in China and promote the realization of China's energy independence strategy.
Research on the Hydrogen Consumption of Fuel Cell Electric Vehicles Based on the Flowmeter and Short-cut Method
Sep 2022
Publication
Energy consumption is essential for evaluating the competitiveness of fuel cell electric vehicles. A critical step in energy consumption measurement is measuring hydrogen consumption including the mass method the P/T method and the flowmeter method. The flowmeter method has always been a research focus because of its simple operation low cost and solid real-time performance. Current research has shown the accuracy of the flowmeter method under specific conditions. However many factors in the real scenario will influence the test result such as unintended vibration environment temperature and onboard hydrogen capacity calibration. On the other hand the short-cut method is also researched to replace the run-out method to improve test efficiency. To evaluate whether the flowmeter method basing on the short-cut method can genuinely reflect the hydrogen consumption of an actual vehicle we research and test for New European Driving Cycle (NEDC) and China Light-Duty Vehicle Test Cycle (CLTC) using the same vehicle. The results show that the short-cut method can save at least 50% of the test time compared with the run-out method. The error of the short-cut method based on the flowmeter for the NEDC working condition is less than 0.1% and for the CLTC working conditions is 8.12%. After adding a throttle valve and a 4L buffer tank the error is reduced to 4.76% from 8.12%. The test results show that hydrogen consumption measurement based on the flowmeter and short-cut method should adopt corresponding solutions according to the scenarios.
Techno-economic Assessment of Electrolytic Hydrogen in China Considering Wind-solar-load Characteristic
Jan 2023
Publication
Hydrogen production by electrolysis is considered an essential means of consuming renewable energy in the future. However the current assessment of the potential of renewable energy electrolysis for hydrogen production is relatively simple and the perspective is not comprehensive. Here we established a Combined Wind and Solar Electrolytic Hydrogen system considering the influence of regional wind-solar-load characteristics and transmission costs to evaluate the hydrogen production potential of 31 provincial-level regions in China in 2050. The results show that in 2050 the levelized cost of hydrogen (LCOH) in China’s provincial regions will still be higher than 10 ¥/kg which is not cost-competitive compared to the current hydrogen production from fossil fuels. It is more cost-effective to deploy wind turbines than photovoltaic in areas with similar wind and solar resources or rich in wind resources. Wind-solar differences impact LCOH equipment capacity configuration and transmission cost composition while load fluctuation significantly impacts LCOH and electricity storage configuration. In addition the sensitivity analysis of 11 technical and economic parameters showed differences in the response performance of LCOH changes to different parameters and the electrolyzer conversion efficiency had the most severe impact. The analysis of subsidy policy shows that for most regions (except Chongqing and Xizang) subsidizing the unit investment cost of wind turbines can minimize LCOH. Nevertheless from the perspective of comprehensive subsidy effect subsidy cost and hydrogen energy development it is more cost-effective to take subsidies for electrolysis equipment with the popularization of hydrogen
Hydrogen Diffusion and Its Effect on Hydrogen Embrittlement in DP Steels with Different Martensite Content
Dec 2020
Publication
The hydrogen diffusion behavior and hydrogen embrittlement susceptibility of dual phase (DP) steels with different martensite content were investigated using the slow strain-rate tensile test and hydrogen permeation measurement. Results showed that a logarithmic relationship was established between the hydrogen embrittlement index (IHE) and the effective hydrogen diffusion coefficient (Deff). When the martensite content is low ferrite/ martensite interface behaves as the main trap that captures the hydrogen atoms. Also when the Deff decreases IHE increases with increasing martensite content. However when the martensite content reaches approximately 68.3% the martensite grains start to form a continuous network Deff reaches a plateau and IHE continues to increase. This is mainly related to the reduction of carbon content in martensite and the length of ferrite/martensite interface which promotes the diffusion of hydrogen atoms in martensite and the aggregation of hydrogen atoms at the ferrite/martensite interface. Finally a model describing the mechanism of microstructure-driven hydrogen diffusion with different martensite distribution was established.
The Role of the Argon and Helium Bath Gases on the Detonation Structure of H2/)2 Mixture
Sep 2021
Publication
Recent modeling efforts of non-equilibrium effects in detonations have suggested that hydrogen-based detonations may be affected by vibrational non-equilibrium of the hydrogen and oxygen molecules effects which could explain discrepancies of cell sizes measured experimentally and calculated without relaxation effects. The present study addresses the role of vibrational relaxation in 2H2/O2 detonations by considering two-bath gases argon and helium. These two gases have the same thermodynamic and kinetic effects when relaxation is neglected. However due to the bath gases differences in molecular weight and reduced mass differences which affect the molecular collisions relaxation rates can be changed by approximately 50-70%. Experiments were performed in a narrow channel in mixtures of 2H2/O2/7Ar and 2H2/O2/7He to evaluate the role of the bath gas on detonation cellular structures. The experiments showed differences in velocity deficits and cell sizes for experimental conditions keeping the induction zone length constant in each of the mixtures. These differences were negligible in sensitive mixtures but increased with the increase in velocity deficits while the cell sizes approaching the channel dimensions. Near the limits differences of cell size in two mixtures approached a factor of 2. These differences were however reconciled by accounting for the viscous losses to the tube walls evaluated using a modified version of Mirels' laminar boundary layer theory and generalized Chapman-Jouguet theory for eigenvalue detonations. The experiments suggest that there is an influence of relaxation effects on the cellular structure of detonations which is more sensitive to wall boundary conditions. However the previous works showed that the impact of vibrational non-equilibrium in a mixture of H2/Air is more visible due to the effects of N2 in the air slowest to relax. Previous discrepancies suggested to be indicative of relaxation effects should be reevaluated by the inclusion of wall loss effects.
The Role of Hydrogen in the Corrosion and Cracking of Steels - A Review
Oct 2021
Publication
In many processes of steel industrial including steel manufacture storage and service hydrogen could be absorbed into metallic materials and the absorbed hydrogen seriously impaired its corrosion resistance. This paper provides a comprehensive review on the effects of hydrogen on passive film anodic dissolution pitting corrosion and stress corrosion cracking and based on the review the mechanism by which hydrogen promotes corrosion of steel and subsequently leads to cracking has been discussed. It is envisaged that hydrogen harms the stability of the passive film and as a result escalates anode’s activation of steel eventually leading to pitting and stress corrosion cracking.
Strategies for the Adoption of Hydrogen-Based Energy Storage Systems: An Exploratory Study in Australia
Aug 2022
Publication
A significant contribution to the reduction of carbon emissions will be enabled through the transition from a centralised fossil fuel system to a decentralised renewable electricity system. However due to the intermittent nature of renewable energy storage is required to provide a suitable response to dynamic loads and manage the excess generated electricity with utilisation during periods of low generation. This paper investigates the use of stationary hydrogen-based energy storage systems for microgrids and distributed energy resource systems. An exploratory study was conducted in Australia based on a mixed methodology. Ten Australian industry experts were interviewed to determine use cases for hydrogen-based energy storage systems’ requirements barriers methods and recommendations. This study suggests that the current cost of the electrolyser fuel cell and storage medium and the current low round-trip efficiency are the main elements inhibiting hydrogen-based energy storage systems. Limited industry and practical experience are barriers to the implementation of hydrogen storage systems. Government support could help scale hydrogen-based energy storage systems among early adopters and enablers. Furthermore collaboration and knowledge sharing could reduce risks allowing the involvement of more stakeholders. Competition and innovation could ultimately reduce the costs increasing the uptake of hydrogen storage systems.
Using Multicriteria Decision Making to Evaluate the Risk of Hydrogen Energy Storage and Transportation in Cities
Jan 2023
Publication
Hydrogen is an environmentally friendly source of renewable energy. Energy generation from hydrogen has not yet been widely commercialized due to issues related to risk management in its storage and transportation. In this paper the authors propose a hybrid multiple-criteria decision-making (MCDM)-based method to manage the risks involved in the storage and transportation of hydrogen (RSTH). First we identified the key points of the RSTH by examining the relevant literature and soliciting the opinions of experts and used this to build a prototype of its decision structure. Second we developed a hybrid MCDM approach called the D-ANP that combined the decision-making trial and evaluation laboratory (DEMENTEL) with the analytic network process (ANP) to obtain the weight of each point of risk. Third we used fuzzy evaluation to assess the level of the RSTH for Beijing China where energy generation using hydrogen is rapidly advancing. The results showed that the skills of the personnel constituted the most important risk-related factor and environmental volatility and the effectiveness of feedback were root factors. These three factors had an important impact on other factors influencing the risk of energy generation from hydrogen. Training and technical assistance can be used to mitigate the risks arising due to differences in the skills of personnel. An appropriate logistics network and segmented transportation for energy derived from hydrogen should be implemented to reduce environmental volatility and integrated supply chain management can help make the relevant feedback more effective.
The Direct Reduction of Iron Ore with Hydrogen
Aug 2022
Publication
The steel industry represents about 7% of the world’s anthropogenic CO2 emissions due to the high use of fossil fuels. The CO2 -lean direct reduction of iron ore with hydrogen is considered to offer a high potential to reduce CO2 emissions and this direct reduction of Fe2O3 powder is investigated in this research. The H2 reduction reaction kinetics and fluidization characteristics of fine and cohesive Fe2O3 particles were examined in a vibrated fluidized bed reactor. A smooth bubbling fluidization was achieved. An increase in external force due to vibration slightly increased the pressure drop. The minimum fluidization velocity was nearly independent of the operating temperature. The yield of the direct H2 -driven reduction was examined and found to exceed 90% with a maximum of 98% under the vibration of ~47 Hz with an amplitude of 0.6 mm and operating temperatures close to 500 ◦C. Towards the future of direct steel ore reduction cheap and “green” hydrogen sources need to be developed. H2 can be formed through various techniques with the catalytic decomposition of NH3 (and CH4 ) methanol and ethanol offering an important potential towards production cost yield and environmental CO2 emission reductions.
Topology and Control of Fuel Cell Generation Converters
Jun 2023
Publication
Fuel cell power generation is one of the important ways of utilizing hydrogen energy which has good prospects for development. However fuel cell volt-ampere characteristics are nonlinear the output voltage is low and the fluctuation range is large and a power electronic converter matching its characteristics is required to achieve efficient and stable work. Based on the analysis of the fuel cell’s characteristic mechanism maximum power point tracking algorithm fuel cell converter characteristics application and converter control strategy the paper summarizes the general principles of the topology of fuel cell converters. In addition based on the development status of new energy hydrogen energy is organically combined with other new energy sources and the concept of 100% absorption system of new energy with green hydrogen as the main body is proposed to provide a reference for the development of hydrogen energy.
A Robust Scheduling Methodology for Integrated Electric-Gas System Considering Dynamics of Natural Gas Pipeline and Blending Hydrogen
Mar 2022
Publication
As smart grid develops and renewables advance challenges caused by uncertainties of renewables have been seriously threatening the energy system’s safe operation. Nowadays the integrated electric-gas system (IEGS) plays a significant role in promoting the flexibility of modern grid owing to its great characteristic in accommodating renewable energy and coping with fluctuation and uncertainty of the system. And hydrogen as an emerging and clean energy carrier can further enhance the energy coupling of the IEGS and promote carbon neutralization with the development of power-to-hydrogen (P2H) technology and technology of blending hydrogen in the natural gas system. Dealing with the uncertainty of renewables a robust schedule optimization model for the integrated electric and gas systems with blending hydrogen (IEGSH) considering the dynamics of gas is proposed and the iterative solving method based on column-and-constraint generation (C&CG) algorithm is implemented to solve the problem. Case studies on the IEGSH consisting of IEEE 39-bus power system and 27-node natural gas system validate the effectiveness of the dynamic energy flow model in depicting the transient process of gas transmission. The effectiveness of the proposed robust day-ahead scheduling model in dealing with the intra-day uncertainty of wind power is also verified. Additionally the carbon emission reduction resulting from the blending of hydrogen is evaluated.
Laminar Burning Velocity, Markstein Length and Cellular Instability of Spherically Propagating NH2/H2/Air Premixed Flames at Various Pressures
Sep 2021
Publication
Blending hydrogen into ammonia can I mprove the burning intensity of ammonia and the safety of hydrogen and it is important to understand the flames of NH3/H2/air mixtures. In this work lamiar flame characteristics of 50-50 (vol%) ammonia-hydrogen mixtures in air were studied using the spherical flame propagation method in a constant-volume bom at initital temperature Tu = 298K and different pressures.
The Spatio-Temporal Evolution of China’s Hydrogen Fuel Cell Vehicle Innovation Network: Evidence From Patent Citation at Provincial Level
Oct 2021
Publication
Hydrogen fuel cell vehicle industry is in a rapid development stage. Studying the domestic spatial distribution of hydrogen fuel cell vehicle industry across a country especially the spatio-temporal evolution of the innovation level and position of each region in innovation network will help to understand the industry’s development trends and characteristics and avoid repeated construction. This article uses social network analysis and patent citation information of 2971 hydrogen fuel cell vehicle related invention patents owned by 218 micro-innovators across 25 provinces of China from 2001 to 2020 to construct China’s hydrogen fuel cell vehicle innovation network. Based on the dimensions of knowledge production knowledge consumption and network broker the network positions of sample provinces in three periods divided by four main national policies are classified. The main findings are as follows. 1) In China the total sales of hydrogen fuel cell vehicle and the development of supporting infrastructure are balanced and a series of national and local industrial development polices have been issued. 2) China’s hydrogen fuel cell vehicle innovation network density the proportion of universities and research institutes among the innovators and the active degree of the eastern provinces are all becoming higher. 3) The provinces in optimal network position are all from the eastern region. Shanghai and Liaoning are gradually replaced by Beijing and Jiangsu. 4) Sichuan in the western region is the only network broker based on knowledge consumption. 5) Although Zhejiang Tianjin Hebei Guangdong and Hubei are not yet in the optimal position they are outstanding knowledge producers. Specifically Guangdong is likely to climb to the optimal network position in the next period. The conclusions will help China’s provinces to formulate relevant development policies to optimize industry layout and enhance collaborative innovation in the hydrogen fuel cell vehicle industry.
Research Progress and Prospects on Hydrogen Damage in Welds of Hydrogen-Blended Natural Gas Pipelines
Nov 2023
Publication
Hydrogen energy represents a crucial pathway towards achieving carbon neutrality and is a pivotal facet of future strategic emerging industries. The safe and efficient transportation of hydrogen is a key link in the entire chain development of the hydrogen energy industry’s “production storage and transportation”. Mixing hydrogen into natural gas pipelines for transportation is the potential best way to achieve large-scale long-distance safe and efficient hydrogen transportation. Welds are identified as the vulnerable points in natural gas pipelines and compatibility between hydrogen-doped natural gas and existing pipeline welds is a critical technical challenge that affects the global-scale transportation of hydrogen energy. Therefore this article systematically discusses the construction and weld characteristics of hydrogen-doped natural gas pipelines the research status of hydrogen damage mechanism and mechanical property strengthening methods of hydrogen-doped natural gas pipeline welds and points out the future development direction of hydrogen damage mechanism research in hydrogen-doped natural gas pipeline welds. The research results show that: 1 Currently there is a need for comprehensive research on the degradation of mechanical properties in welds made from typical pipe materials on a global scale. It is imperative to systematically elucidate the mechanism of mechanical property degradation due to conventional and hydrogeninduced damage in welds of high-pressure hydrogen-doped natural gas pipelines worldwide. 2 The deterioration of mechanical properties in welds of hydrogen-doped natural gas pipelines is influenced by various components including hydrogen carbon dioxide and nitrogen. It is necessary to reveal the mechanism of mechanical property deterioration of pipeline welds under the joint participation of multiple damage mechanisms under multi-component gas conditions. 3 Establishing a fundamental database of mechanical properties for typical pipeline steel materials under hydrogen-doped natural gas conditions globally is imperative to form a method for strengthening the mechanical properties of typical high-pressure hydrogen-doped natural gas pipeline welds. 4 It is essential to promptly develop relevant standards for hydrogen blending transportation welding technology as well as weld evaluation testing and repair procedures for natural gas pipelines.
Thermal Sprayed Protective Coatings for Bipolar Plates of Hydrogen Fuel Cells and Water Electrolysis Cells
Mar 2024
Publication
As one core component in hydrogen fuel cells and water electrolysis cells bipolar plates (BPs) perform multiple important functions such as separating the fuel and oxidant flow providing mechanical support conducting electricity and heat connecting the cell units into a stack etc. On the path toward commercialization the manufacturing costs of bipolar plates have to be substantially reduced by adopting low-cost and easy-to-process metallic materials (e.g. stainless steel aluminum or copper). However these materials are susceptible to electrochemical corrosion under harsh operating conditions resulting in long-term performance degradation. By means of advanced thermal spraying technologies protective coatings can be prepared on bipolar plates so as to inhibit oxidation and corrosion. This paper reviews several typical thermal spraying technologies including atmospheric plasma spraying (APS) vacuum plasma spraying (VPS) and high-velocity oxygen fuel (HVOF) spraying for preparing coatings of bipolar plates particularly emphasizing the effect of spraying processes on coating effectiveness. The performance of coatings relies not only on the materials as selected or designed but also on the composition and microstructure practically obtained in the spraying process. The temperature and velocity of in-flight particles have a significant impact on coating quality; therefore precise control over these factors is demanded.
Inter-Zone Optimal Scheduling of Rural Wind–Biomass-Hydrogen Integrated Energy System
Aug 2023
Publication
To solve the problems of low utilization of biomass and uncertainty and intermittency of wind power (WP) in rural winter an interval optimization model of a rural integrated energy system with biogas fermentation and electrolytic hydrogen production is constructed in this paper. Firstly a biogas fermentation kinetic model and a biogas hydrogen blending model are developed. Secondly the interval number is used to describe the uncertainty of WP and an interval optimization scheduling model is developed to minimize daily operating cost. Finally a rural integrated energy system in Northeast China is taken as an example and a sensitivity analysis of electricity price gas production and biomass price is conducted. The simulation results show that the proposed strategy can significantly reduce the wind abandonment rate and improve the economy by 3.8–22.3% compared with conventional energy storage under optimal dispatch.
Green Hydrogen Production and Liquefaction Using Offshore Wind Power, Liquid Air, and LNG Cold Energy
Sep 2023
Publication
Coastal regions have abundant off-shore wind energy resources and surrounding areas have large-scale liquefied natural gas (LNG) receiving stations. From the engineering perspectives there are limitations in unstable off-shore wind energy and fluctuating LNG loads. This article offers a new energy scheme to combine these 2 energy units which uses surplus wind energy to produce hydrogen and use LNG cold energy to liquefy and store hydrogen. In addition in order to improve the efficiency of utilizing LNG cold energy and reduce electricity consumption for liquid hydrogen (LH2) production at coastal regions this article introduces the liquid air energy storage (LAES) technology as the intermediate stage which can stably store the cold energy from LNG gasification. A new scheme for LNG-LAES-LH2 hybrid LH2 production is built. The case study is based on a real LNG receiving station at Hainan province China and this article presents the design of hydrogen production/liquefaction process and carries out the optimizations at key nodes and proves the feasibility using specific energy consumption and exergy analysis. In a 100 MW system the liquid air storage round-trip efficiency is 71.0% and the specific energy consumption is 0.189 kWh/kg and the liquid hydrogen specific energy consumption is 7.87 kWh/kg and the exergy efficiency is 46.44%. Meanwhile the corresponding techno-economic model is built and for a LNGLAES-LH2 system with LH2 daily production 140.4 tons the shortest dynamic payback period is 9.56 years. Overall this novel hybrid energy scheme can produce green hydrogen using a more efficient and economical method and also can make full use of surplus off-shore wind energy and coastal LNG cold energy.
Drifting toward Alliance Innovation: Patent Collaboration Relationships and Development in China’s Hydrogen Energy Industry from a Network Perspective
Mar 2024
Publication
The hydrogen energy industry as one of the most important directions for future energy transformation can promote the sustainable development of the global economy and of society. China has raised the development of hydrogen energy to a strategic position. Based on the patent data in the past two decades this study investigates the collaborative innovation relationships in China’s hydrogen energy field using complex network theory. Firstly patent data filed between 2003 and 2023 are analyzed and compared in terms of time geography and institutional and technological dimensions. Subsequently a patent collaborative innovation network is constructed to explore the fundamental characteristics and evolutionary patterns over five stages. Furthermore centrality measures and community detection algorithms are utilized to identify core entities and innovation alliances within the network which reveal that China’s hydrogen energy industry is drifting toward alliance innovation. The study results show the following: (1) the network has grown rapidly in size and scope over the last two decades and evolved from the initial stage to the multi-center stage before forming innovation alliances; (2) core innovative entities are important supports and bridges for China’s hydrogen energy industry and control most resources and maintain the robustness of the whole network; (3) innovation alliances reveal the closeness of the collaborative relationships between innovative entities and the potential landscape of China’s hydrogen energy industry; and (4) most of the innovation alliances cooperate only on a narrow range of technologies which may hinder the overall sustainable growth of the hydrogen energy industry. Thereafter some suggestions are put forward from the perspective of an industrial chain and innovation chain which may provide a theoretical reference for collaborative innovation and the future development and planning in the field of hydrogen energy in China.
Willingness of Chinese Households to Pay Extra for Hydrogen-fuelled Buses: A Survey Based on Willingness to Pay
Mar 2023
Publication
Hydrogen-fuelled buses play an important role in the construction of low-carbon cities as a means of green travel. Beijing as a pilot city of hydrogen-fuelled buses in China is very important in the promotion of hydrogen-fuelled buses in China. Unfortunately the public acceptance of hydrogen-fuelledfuelled buses and their environmental positive externality value have not been studied. In this paper we investigated the willingness of Beijing households to pay for the promotion of hydrogen-fuelled buses and its influencing factors by means of a web-based questionnaire. The spike model was also used to estimate the willingness to pay (WTP) for hydrogen buses. The results show that the WTP of Beijing households is CNY 3.19 per trip. The value of a positive environmental externality is approximately CNY 29.15 million per trip. Household income level environmental knowledge individual environmental ethics and perceived behavioural control are the main influencing factors of WTP. Therefore policymakers should strengthen publicity efforts to increase individuals’ environmental awareness and environmental ethics and optimize the layout of hydrogen-fuelled bus schedules and riding experiences to improve individuals’ perceptual and behaviour control. Finally the positive environmental externality value of hydrogen buses should be valued which will help increase investor interest.
Research on Fast Frequency Response Control Strategy of Hydrogen Production Systems
Mar 2024
Publication
With the large-scale integration of intermittent renewable energy generation presented by wind and photovoltaic power the security and stability of power system operations have been challenged. Therefore this article proposes a control strategy of a hydrogen production system based on renewable energy power generation to enable the fast frequency response of a grid. Firstly based on the idea of virtual synchronous control a fast frequency response control transformation strategy for the grid-connected interface of hydrogen production systems for renewable energy power generation is proposed to provide active power support when the grid frequency is disturbed. Secondly based on the influence of VSG’s inertia and damping coefficient on the dynamic characteristics of the system a VSG adaptive control model based on particle swarm optimization is designed. Finally based on the Matlab/Simulink platform a grid-connected simulation model of hydrogen production systems for renewable energy power generation is established. The results show that the interface-transformed electrolytic hydrogen production device can actively respond to the frequency disturbances of the power system and participate in primary frequency control providing active support for the frequency stability of the power system under high-percentage renewable energy generation integration. Moreover the system with parameter optimization has better fast frequency response control characteristics.
No more items...