- Home
- A-Z Publications
- Publications
Publications
Re-enacting the Hydrogen Tank Explosion of a Fuel-cell Electric Vehicle: An Experimental Study
May 2023
Publication
With the world-wide decision to reduce carbon emissions through the Paris Agreement (2015) the demand for hydrogen-fuelled vehicles has been increasing. Although hydrogen is not a toxic gas it has a wide flammable range (4e75%) and can explode due to static electricity. Therefore studies on hydrogen safety are urgently required. In this study an explosion was induced by applying fire to the lower part of a fuel cell electric vehicle (FCEV). Out of three compressed hydrogen storage tanks installed in the vehicle two did not have hydrogen fuel and one was filled with compressed gaseous hydrogen of 700 bar and forcedly deactivated its temperature-activated pressure relief device. The side-on overpressure transducers were installed by distance in main directions to measure the side-on overpressure generated by the vehicle explosion. A 10 m-long protective barrier was installed on which reflected overpressure displacement and acceleration were measured to examine the effect of attenuation of explosion damage in the event of an accident. The vehicle exploded approximately 11 min after ignition generating a blast wave fireballs and fragments. The results of the experiment showed that the protective barrier could almost completely block explosive pressure smoke and scattering generated during an explosion. Through Probit function analysis the probabilities of an accident occurring were derived based on peak overpressure peak impulse and scattering. The results of this study can be used to develop standard operating procedures (SOPs) for firefighters as the base data for setting the initial operation location and deriving the safe separation distance.
Hybrid Electric Vehicle: Design and Control of a Hybrid System (Fuel Cell/Battery/Ultra-Capacitor) Supplied by Hydrogen
Apr 2019
Publication
Due to its high efficiency and reduced emissions new zero-emission hybrid electric vehicles have been selected as an attractive challenge for future transport applications. New zero -emission hybrid electric on the other hand has some major drawbacks from the complicated charging process. The hybrid electrical fuel cell system is introduced as the main source to intelligently control multi-source activities. An ultra-capacitor system is selected as the energy recovery assistance to monitor the fuel cell’s fast transient and peak power during critical periods. To regulate energy demand and supply an intelligent energy management system is proposed and tested through several constraints. The proposed approach system aims to act quickly against sudden circumstances related to hydrogen depletion in the prediction of the required fuel consumption basis. The proposed strategy tends to define the proper operating system according to energy demand and supply. The obtained results show that the designed system meets the targets set for the energy management unit by referring to an experimental velocity database.
Design and Analysis of a New Renewable-Nuclear Hybrid Energy System for Production of Hydrogen, Fresh Water and Power
Nov 2021
Publication
This paper investigates an integrated system where solar energy system (with 75MWp bifacial PV arrays) and nuclear power plant (with 2×10MWt HTR-10 type pebble bed reactors) are hybridized and integrated with a 72MWe capacity high-temperature solid oxide electrolysis (SOE) unit to produce hydrogen fresh water and electrical power. Bifacial PV plant is integrated to system for supplying electricity with a low LCOE and zero-carbon system. A Rankine cycle is integrated to generate power from the steam that generated from nuclear heat. According to the available irradiance; the steam is diverted between steam turbine and high-temperature electrolyzer for hydrogen and power generation. Multi-effect desalination unit is integrated to exploit the excess heat to generate fresh water. A system performance assessment is carried out by energy and exergy efficiencies thermodynamically. The bifacial PV plant is analyzed in six selected latitudes in order to assess the feasibility and applicability of the system. Numerous time-dependent analyses are carried out to study the effects of varying inputs such as solar radiation intensity. For 20MWt nuclear 75MWp solar capacity; hydrogen productions are found to be between 0.036 and 0.562kg/s. Among the Northern Hemisphere latitudes the peak daily hydrogen production rate is expected to reach 25.9 tons of hydrogen per day for the 75 °N case mostly with the influence of low temperature and high albedo. The pitch distance change is increased the hydrogen production rate by 28% between 3 m and 7 m tracker spacing. The overall system energy efficiency is obtained between 21.8% and 24.2% where the overall system exergy efficiency is found between 18.6% and 21.1% under dynamic conditions for the 45°N latitude case.
Hydrogen Energy Storage: New Techno-economic Emergence Solution Analysis
Aug 2015
Publication
The integration of various renewable energy sources as well as the liberalization of electricity markets are established facts in modern electrical power systems. The increased share of renewable sources within power systems intensifies the supply variability and intermittency. Therefore energy storage is deemed as one of the solutions for stabilizing the supply of electricity to maintain generation-demand balance and to guarantee uninterrupted supply of energy to users. In the context of sustainable development and energy resources depletion the question of the growth of renewable energy electricity production is highly linked to the ability to propose new and adapted energy storage solutions. The purpose of this multidisciplinary paper is to highlight the new hydrogen production and storage technology its efficiency and the impact of the policy context on its development. A comprehensive techno/socio/economic study of long term hydrogen based storage systems in electrical networks is addressed. The European policy concerning the different energy storage systems and hydrogen production is explicitly discussed. The state of the art of the techno-economic features of the hydrogen production and storage is introduced. Using Matlab-Simulink for a power system of rated 70 kW generator the excess produced hydrogen during high generation periods or low demand can be sold either directly to the grid owners or as filled hydrogen bottles. The affordable use of Hydrogen-based technologies for long term electricity storage is verified.
From Grey to Green and from West to East: The Geography and Innovation Trajectories of Hydrogen Fuel Technologies
May 2023
Publication
Despite the potential of hydrogen as a sustainable energy carrier existing studies analysing the recent evolution of this technology are scattered typically focusing on a specific type of hydrogen technology within a single country or region. In this paper we adopt a broader perspective providing an overview of the evolution of knowledge generation across different types of hydrogen fuel and the leading countries in developing new technologies in this field. Using data from the European Patent Office we map knowledge generation on hydrogen fuel technologies exploring its geographic distribution and its link with environmental sustainability. While the United States leads the generation of new knowledge other Asian and European countries show greater dynamism in growth and specialisation. Our study shows that although hydrogen fuel is considered environmentally friendly most recent technological developments are still related to fossil energy sources. However a faster growth rate is observed in the knowledge of hydrogen fuel from renewable sources pointing to a promising path towards sustainability. Moreover our analysis of the knowledge interconnection between different hydrogen types suggests that those technologies developed for hydrogen based on fossil energy sources have enabled novel applications based on renewable energies.
Material Challenges and Hydrogen Embrittlement Assessment for Hydrogen Utilisation in Industrial Scale
Sep 2023
Publication
Hydrogen has been studied extensively as a potential enabler of the energy transition from fossil fuels to renewable sources. It promises a feasible decarbonisation route because it can act as an energy carrier a heat source or a chemical reactant in industrial processes. Hydrogen can be produced via renewable energy sources such as solar hydro or geothermic routes and is a more stable energy carrier than intermittent renewable sources. If hydrogen can be stored efficiently it could play a crucial role in decarbonising industries. For hydrogen to be successfully implemented in industrial systems its impact on infrastructure needs to be understood quantified and controlled. If hydrogen technology is to be economically feasible we need to investigate and understand the retrofitting of current industrial infrastructure. Currently there is a lack of comprehensive knowledge regarding alloys and components performance in long-term hydrogen-containing environments at industrial conditions associated with high-temperature hydrogen processing/production. This review summarises insights into the gaps in hydrogen embrittlement (HE) research that apply to high-temperature high-pressure systems in industrial processes and applications. It illustrates why it is still important to develop characterisation techniques and methods for hydrogen interaction with metals and surfaces under these conditions. The review also describes the implications of using hydrogen in large-scale industrial processes.
Hydrogen Deep Ocean Link: A Global Sustainable Interconnected Energy Grid<br/><br/><br/>
Mar 2022
Publication
The world is undergoing a substantial energy transition with an increasing share of intermittent sources of energy on the grid which is increasing the challenges to operate the power grid reliably. An option that has been receiving much focus after the COVID pandemic is the development of a hydrogen economy. Challenges for a hydrogen economy are the high investment costs involved in compression storage and long-distance transportation. This paper analyses an innovative proposal for the creation of hydrogen ocean links. It intends to fill existing gaps in the creation of a hydrogen economy with the increase in flexibility and viability for hydrogen production consumption compression storage and transportation. The main concept behind the proposals presented in this paper consists of using the fact that the pressure in the deep sea is very high which allows a thin and cheap HDPE tank to store and transport large amounts of pressurized hydrogen in the deep sea. This is performed by replacing seawater with pressurized hydrogen and maintaining the pressure in the pipes similar to the outside pressure. Hydrogen Deep Ocean Link has the potential of increasing the interconnectivity of different regional energy grids into a global sustainable interconnected energy system.
Inter-Zone Optimal Scheduling of Rural Wind–Biomass-Hydrogen Integrated Energy System
Aug 2023
Publication
To solve the problems of low utilization of biomass and uncertainty and intermittency of wind power (WP) in rural winter an interval optimization model of a rural integrated energy system with biogas fermentation and electrolytic hydrogen production is constructed in this paper. Firstly a biogas fermentation kinetic model and a biogas hydrogen blending model are developed. Secondly the interval number is used to describe the uncertainty of WP and an interval optimization scheduling model is developed to minimize daily operating cost. Finally a rural integrated energy system in Northeast China is taken as an example and a sensitivity analysis of electricity price gas production and biomass price is conducted. The simulation results show that the proposed strategy can significantly reduce the wind abandonment rate and improve the economy by 3.8–22.3% compared with conventional energy storage under optimal dispatch.
Life Cycle Assessment of an Autonomous Underwater Vehicle that Employs Hydrogen Fuel Cell
Aug 2023
Publication
In recent years there has been a significant increase in the adoption of autonomous vehicles for marine and submarine missions. The advancement of emerging imaging navigation and communication technologies has greatly expanded the range of operational capabilities and opportunities available. The ENDURUNS project is a European research endeavor focused on identifying strategies for achieving minimal environmental impact. To measure these facts this article evaluates the product impacts employing the Life Cycle Assessment methodology for the first time following the ISO 14040 standard. In this analysis the quantitative values of Damage and Environmental Impact using the Eco-Indicator 99 methodology in SimaPro software are presented. The results report that the main contributors in environmental impact terms have been placed during the manufacturing phase. Thus one of the challenges is accomplished avoiding the use phase emissions that are the focus to reduce nowadays in the marine industry.
Increasing Energy Efficiency of Hydrogen Refueling Stations via Optimal Thermodynamic Paths
Sep 2023
Publication
This work addresses the energy efficiency of hydrogen refueling stations (HRS) using a first principles model and optimal control methods to find minimal entropy production operating paths. The HRS model shows good agreement with experimental data achieving maximum state of charge and temperature discrepancies of 1 and 7% respectively. Model solution and optimization is achieved at a relatively low computational time (40 s) when compared to models of the same degree of accuracy. The entropy production mapping indicates the flow control valve as the main source of irreversibility accounting for 85% of the total entropy production in the process. The minimal entropy production refueling path achieves energy savings from 20 to 27% with respect to the SAE J2601 protocol depending on the ambient temperature. Finally the proposed method under nearreversible refueling conditions shows a theoretical reduction of 43% in the energy demand with respect to the SAE J2601 protocol.
A Rational Approach to the Ecological Transition in the Cruise Market: Technologies and Design Compromises for the Fuel Switch
Jan 2023
Publication
Supporting policies to achieve a green revolution and ecological transition is a global trend. Although the maritime transport of goods and people can rightly be counted among the least polluting sectors much can be done to further reduce its environmental footprint. Moreover to boost the ecological transition of vessels a whole series of international regulations and national laws have been promulgated. Among these the most impactful on both design and operational management of ships concern the containment of air-polluting emissions in terms of GHG NOx SOx and PM. To address this challenge it might seem that many technologies already successfully used in other transport sectors could be applied. However the peculiar characteristics of ships make this statement not entirely true. In fact technological solutions recently adopted for example in the automotive sector must deal with the large size of vessels and the consequent large amount of energy necessary for their operation. In this paper with reference to the case study of a medium/large-sized passenger cruise ship the use of different fuels (LNG ammonia hydrogen) and technologies (internal combustion engines fuel cells) for propulsion and energy generation on board will be compared. By imposing the design constraint of not modifying the payload and the speed of the ship the criticalities linked to the use of one fuel rather than another will be highlighted. The current limits of application of some fuels will be made evident with reference to the state of maturity of the relevant technologies. Furthermore the operational consequences in terms of autonomy reduction will be presented. The obtained results underline the necessity for shipowners and shipbuilders to reflect on the compromises required by the challenges of the ecological transition which will force them to choose between reducing payload or reducing performance.
Green Steel: Synergies between the Australian Iron Ore Industry and the Production of Green Industry
May 2023
Publication
Green steel produced using renewable energy and hydrogen presents a promising avenue to decarbonize steel manufacturing and expand the hydrogen industry. Australia endowed with abundant renewable resources and iron ore deposits is ideally placed to support this global effort. This paper's two-step analytical approach offers the first comprehensive assessment of Australia's potential to develop green steel as a value-added export commodity. The Economic Fairways modelling reveals a strong alignment between prospective hydrogen hubs and current and future iron ore operations enabling shared infrastructure development and first-mover advantages. By employing a site-based system optimization that integrates both wind and solar power sources the cost of producing green steel could decrease significantly to around AU$900 per tonne by 2030 and AU$750 per tonne by 2050. Moreover replacing 1% of global steel production would require 35 GW of well-optimized wind and solar photovoltaics 11 GW of hydrogen electrolysers and 1000 square kilometres of land. Sensitivity analysis further indicates that iron ore prices would exert a long-term influence on green steel prices. Overall this study highlights the opportunities and challenges facing the Australian iron ore industry in contributing to the decarbonization of the global steel sector underscoring the crucial role of government support in driving the growth and development of the green steel industry.
Synergistic Integration of Hydrogen Energy Economy with UK’s Sustainable Development Goals: A Holistic Approach to Enhancing Safety and Risk Mitigation
Oct 2023
Publication
Hydrogen is gaining prominence as a sustainable energy source in the UK aligning with the country’s commitment to advancing sustainable development across diverse sectors. However a rigorous examination of the interplay between the hydrogen economy and the Sustainable Development Goals (SDGs) is imperative. This study addresses this imperative by comprehensively assessing the risks associated with hydrogen production storage transportation and utilization. The overarching aim is to establish a robust framework that ensures the secure deployment and operation of hydrogen-based technologies within the UK’s sustainable development trajectory. Considering the unique characteristics of the UK’s energy landscape infrastructure and policy framework this paper presents practical and viable recommendations to facilitate the safe and effective integration of hydrogen energy into the UK’s SDGs. To facilitate sophisticated decision making it proposes using an advanced Decision-Making Trial and Evaluation Laboratory (DEMATEL) tool incorporating regret theory and a 2-tuple spherical linguistic environment. This tool enables a nuanced decision-making process yielding actionable insights. The analysis reveals that Incident Reporting and Learning Robust Regulatory Framework Safety Standards and Codes are pivotal safety factors. At the same time Clean Energy Access Climate Action and Industry Innovation and Infrastructure are identified as the most influential SDGs. This information provides valuable guidance for policymakers industry stakeholders and regulators. It empowers them to make well-informed strategic decisions and prioritize actions that bolster safety and sustainable development as the UK transitions towards a hydrogen-based energy system. Moreover the findings underscore the varying degrees of prominence among different SDGs. Notably SDG 13 (Climate Action) exhibits relatively lower overall distinction at 0.0066 and a Relation value of 0.0512 albeit with a substantial impact. In contrast SDG 7 (Clean Energy Access) and SDG 9 (Industry Innovation and Infrastructure) demonstrate moderate prominence levels (0.0559 and 0.0498 respectively) each with its unique influence emphasizing their critical roles in the UK’s pursuit of a sustainable hydrogen-based energy future.
Economic Performance Evaluation of Flexible Centralised and Decentralised Blue Hydrogen Production Systems Design Under Uncertainty
Sep 2023
Publication
Blue hydrogen is viewed as an important energy vector in a decarbonised global economy but its large-scale and capital-intensive production displays economic performance vulnerabities in the face of increased market and regulatory uncertainty. This study analyses flexible (modular) blue hydrogen production plant designs and evaluates their effectiveness to enhance economic performance under uncertainty. The novelty of this work lies in the development of a comprehensive techno-economic evaluation framework that considers flexible centralised and decentralised blue hydrogen plant design alternatives in the presence of irreducible uncertainty whilst explicitly considering the time value of money economies of scale and learning effects. A case study of centralised and decentralised blue hydrogen production for the transport sector in the San Francisco area is developed to highlight the underlying value of flexibility. The proposed methodological framework considers various blue hydrogen plant designs (fixed phased and flexible) and compares them using relevant economic indicators (net present value (NPV) capex value-at-risk/gain etc.) through a detailed Monte Carlo simulation framework. Results indicate that flexible centralised hydrogen production yields greater economic value than alternative designs despite the associated cost-premium of modularity. It is also shown that the value of flexibility increases under greater uncertainty higher learning rates and weaker economies of scale. Moreover sensitivity analysis reveals that flexible design remains the preferred investment option over a wide range of market and regulatory conditions except for high initial hydrogen demand. Finally this study demonstrates that major regulatory and market uncertainties surrounding blue hydrogen production can be effectively managed through the application of flexible engineering system design that protects the investment from major downside risks whilst allowing access to favourable upside opportunities.
Underground Hydrogen Storage (UHS) in Natural Storage Sites: A Perspective of Subsurface Characterization and Monitoring
Jan 2024
Publication
With the long-standing efforts of green transition in our society underground hydrogen storage (UHS) has emerged as a viable solution to buffering seasonal fluctuations of renewable energy supplies and demands. Like operations in hydrocarbon production and geological CO2 storage a successful UHS project requires a good understanding of subsurface formations while having different operational objectives and practical challenges. Similar to the situations in hydrocarbon production and geological CO2 storage in UHS problems the information of subsurface formations at the field level cannot be obtained through direct measurements due to the resulting high costs. As such there is a need for subsurface characterization and monitoring at the field scale which uses a certain history matching algorithm to calibrate a numerical subsurface model based on available field data. Whereas subsurface characterization and monitoring have been widely used in hydrocarbon production activities for a better understanding of hydrocarbon reservoirs to the best of our knowledge at present it appears to be a relatively less touched area in UHS problems. This work aims to narrow this noticed gap and investigates the use of an ensemble-based workflow for subsurface characterization and monitoring in a 3D UHS case study. Numerical results in this case study indicate that the ensemble-based workflow works reasonably well while also identifying some particular challenges that would be relevant to real-world problems.
Economic Modelling of Mixing Hydrogen with Natural Gas
Jan 2024
Publication
As global efforts intensify to transition toward cleaner and more sustainable energy sources the blending of hydrogen with natural gas emerges as a promising strategy to reduce carbon emissions and enhance energy security. This study employs a systematic approach to assess the economic viability of hydrogen blending considering factors such as gas costs and heat values. Various hydrogen blending scenarios are analyzed to determine the optimal blend ratios taking into account both technical feasibility and economic considerations. The study discusses potential economic benefits challenges and regulatory implications associated with the widespread adoption of hydrogen–natural gas mixtures. Furthermore the study explores the impact of this integration on existing natural gas infrastructure exploring the potential for enhanced energy storage and delivery. The findings of this research contribute valuable insights to policymakers industry stakeholders and researchers engaged in the ongoing energy transition by providing a nuanced understanding of the economic dimensions of hydrogen blending within the natural gas sector.
Improvement of SI Engine Combustion with Ammonia as Fuel: Effect of Ammonia Dissociation Prior to Combustion
Mar 2022
Publication
Although recent studies have shown the possibility of running ‘standard’ spark-ignition engines with 6 pure ammonia the operating range remains limited mainly due to the unfavorable characteristics of 7 ammonia for premixed combustion and often requires the addition of a complementary fuel such as H2 8 to extend it. As the best way to add H2 is to crack ammonia directly on-board this paper focuses on 9 the impact of the upstream cracking level of ammonia on the performance and emissions of a single 10 cylinder spark ignition engine. Experiments were performed over several equivalence ratios 11 dissociation rates and load conditions. It is confirmed that only a slight rate of ammonia dissociation 12 (10%) upstream of the combustion considerably enhances the engine's operating range thanks to a 13 better combustion stability. In terms of pollutant emissions the partial dissociation of ammonia 14 especially for slightly lean mixtures induces a very clear trade-off between high NOx and high 15 unburned ammonia level for high and low ammonia dissociation rates respectively. Therefore 16 cracking NH3 does not only improve the operating range of ammonia-fueled spark ignition engines but 17 can also help to reduce NH3. However to reach the same engine output work higher ammonia fuel 18 consumption will be necessary since the global system efficiency is lower using fuel dissociation. In 19 addition the global warming effect is increased with dissociation level since a higher level of N2O is 20 generated by the hydrogen contribution.
Green Hydrogen Production and Liquefaction Using Offshore Wind Power, Liquid Air, and LNG Cold Energy
Sep 2023
Publication
Coastal regions have abundant off-shore wind energy resources and surrounding areas have large-scale liquefied natural gas (LNG) receiving stations. From the engineering perspectives there are limitations in unstable off-shore wind energy and fluctuating LNG loads. This article offers a new energy scheme to combine these 2 energy units which uses surplus wind energy to produce hydrogen and use LNG cold energy to liquefy and store hydrogen. In addition in order to improve the efficiency of utilizing LNG cold energy and reduce electricity consumption for liquid hydrogen (LH2) production at coastal regions this article introduces the liquid air energy storage (LAES) technology as the intermediate stage which can stably store the cold energy from LNG gasification. A new scheme for LNG-LAES-LH2 hybrid LH2 production is built. The case study is based on a real LNG receiving station at Hainan province China and this article presents the design of hydrogen production/liquefaction process and carries out the optimizations at key nodes and proves the feasibility using specific energy consumption and exergy analysis. In a 100 MW system the liquid air storage round-trip efficiency is 71.0% and the specific energy consumption is 0.189 kWh/kg and the liquid hydrogen specific energy consumption is 7.87 kWh/kg and the exergy efficiency is 46.44%. Meanwhile the corresponding techno-economic model is built and for a LNGLAES-LH2 system with LH2 daily production 140.4 tons the shortest dynamic payback period is 9.56 years. Overall this novel hybrid energy scheme can produce green hydrogen using a more efficient and economical method and also can make full use of surplus off-shore wind energy and coastal LNG cold energy.
Drifting toward Alliance Innovation: Patent Collaboration Relationships and Development in China’s Hydrogen Energy Industry from a Network Perspective
Mar 2024
Publication
The hydrogen energy industry as one of the most important directions for future energy transformation can promote the sustainable development of the global economy and of society. China has raised the development of hydrogen energy to a strategic position. Based on the patent data in the past two decades this study investigates the collaborative innovation relationships in China’s hydrogen energy field using complex network theory. Firstly patent data filed between 2003 and 2023 are analyzed and compared in terms of time geography and institutional and technological dimensions. Subsequently a patent collaborative innovation network is constructed to explore the fundamental characteristics and evolutionary patterns over five stages. Furthermore centrality measures and community detection algorithms are utilized to identify core entities and innovation alliances within the network which reveal that China’s hydrogen energy industry is drifting toward alliance innovation. The study results show the following: (1) the network has grown rapidly in size and scope over the last two decades and evolved from the initial stage to the multi-center stage before forming innovation alliances; (2) core innovative entities are important supports and bridges for China’s hydrogen energy industry and control most resources and maintain the robustness of the whole network; (3) innovation alliances reveal the closeness of the collaborative relationships between innovative entities and the potential landscape of China’s hydrogen energy industry; and (4) most of the innovation alliances cooperate only on a narrow range of technologies which may hinder the overall sustainable growth of the hydrogen energy industry. Thereafter some suggestions are put forward from the perspective of an industrial chain and innovation chain which may provide a theoretical reference for collaborative innovation and the future development and planning in the field of hydrogen energy in China.
Economic Evaluation of a Power-to-hydrogen System Providing Frequency Regulation Reserves: A Case Study of Denmark
Mar 2023
Publication
Operating costs are dominant in the hydrogen production of a power-to-hydrogen system. An optimal operational strategy or bidding framework is effective in reducing these costs. However it is still found that the production cost of hydrogen is high. As the electrolysis unit is characterized by high flexibility providing ancillary service to the grid becomes a potential pathway for revenue stacking. Recent research has demonstrated the feasibility of providing such a service but the related economics have not been well evaluated. In this work we propose a comprehensive operation model to enable participation in the day-head balancing and reserve markets. Three types of reserves are considered by using different operational constraints. Based on the proposed operation framework we assess the economic performance of a power-to-hydrogen system in Denmark using plentiful actual market data. The results reveal that providing frequency containment reserve and automatic frequency restoration reserve efficiently raises the operational contribution margins. In parallel by investing in the cash flows net present value and break-even hydrogen prices we conclude that providing reserves makes the power-to-hydrogen project more profitable in the studied period and region.
How do Variations in Ship Operation Impact the Techno-economic Feasibility and Environmental Performance of Fossil-free Fuels? A Life Cycle Study
Aug 2023
Publication
Identifying an obvious non-fossil fuel solution for all ship types for meeting the greenhouse gas reduction target in shipping is challenging. This paper evaluates the technical viability environmental impacts and economic feasibility of different energy carriers for three case vessels of different ship types: a RoPax ferry a tanker and a service vessel. The energy carriers examined include battery-electric and three electro-fuels (hydrogen methanol and ammonia) which are used in combination with engines and fuel cells. Three methods are used: preliminary ship design feasibility life cycle assessment and life cycle costing. The results showed that battery-electric and compressed hydrogen options are not viable for some ships due to insufficient available onboard space for energy storage needed for the vessel's operational range. The global warming reduction potential is shown to depend on the ship type. This reduction potential of assessed options changes also with changes in the carbon intensity of the electricity mix. Life cycle costing results shows that the use of ammonia and methanol in engines has the lowest life cycle cost for all studied case vessels. However the higher energy conversion losses of these systems make them more vulnerable to fluctuations in the price of electricity. Also these options have higher environmental impacts on categories like human toxicity resource use (minerals and metals) and water use. Fuel cells and batteries are not as cost-competitive for the case vessels because of their higher upfront costs and shorter lifetimes. However these alternatives are less expensive than alternatives with internal combustion engines in the case of higher utilization rates and fuel costs.
Experimental Study of Cycle-by-cycle Variations in a Spark Ignition Internal Combustion Engine Fueled with Hydrogen
Feb 2024
Publication
High fluctuations in the combustion process from one cycle to another referred to as cycle-by-cycle variations can have adverse effects on internal combustion engine performances particularly in spark ignition (SI) engines. These effects encompass incomplete combustion the potential for misfires and adverse impacts on fuel economy. Furthermore the cycle-by-cycle variations can also affect a vehicle’s drivability and overall comfort especially when operating under lean-burn conditions. Although many cycle-by-cycle analyses have been investigated extensively in the past there is limited in-depth knowledge available regarding the causes of cycle-by-cycle (CbC) variations in hydrogen lean-burn SI engines. Trying to contribute to this topic the current study presents a comprehensive analysis of the CbC variations based on the cylinder pressure data. The study was carried out employing a hydrogen single-cylinder research SI engine. The experiments were performed by varying more than fifty operating conditions including the variations in lambda spark advance boost pressure and exhaust gas recirculation however the load and speed were kept constant throughout the experimental campaign. The results indicate that pressure exhibits significant variations during the combustion process and minor variations during non-combustion processes. In the period from the inlet valve close till the start of combustion pressure exhibits the least variations. The coefficient of variation of pressure (COVP) curve depicts three important points in H2-ICE as well: global minima global maxima and second local minima. The magnitude of the COVP curve changes across all the operating conditions however the shape of the COVP curve remains unchanged across all the operating conditions indicating its independence from the operating condition in an H2-ICE. This study presents an alternative approach for a quick combustion analysis of hydrogen engines. Without the need for more complex methodologies like heat release rate analysis the presented cylinder pressure cycle-by-cycle analysis enables a quick and precise identification of primary combustion features (start of combustion center of combustion end of combustion and operation condition stability). Additionally the engine control unit could implement these procedures to automatically adjust cycle-by-cycle variations therefore increasing engine efficiency.
Parameterization Proposal to Determine the Feasibility of Geographic Areas for the Green Hydrogen Industry under Socio-environmental and Technical Constraints in Chile
Oct 2023
Publication
Chile abundant in solar and wind energy resources presents significant potential for the production of green hydrogen a promising renewable energy vector. However realizing this potential requires an understanding of the most suitable locations for the installation of green hydrogen industries. This study proposes a quantitative methodology that identifies and ranks potential public lands for industrial use based on a range of technical parameters (such as solar and wind availability) and socio-environmental considerations (including land use restrictions and population density). The results reveal optimal locations that can facilitate informed sustainable decision-making for large-scale green hydrogen implementation in Chile. While this methodology does not replace project-specific technical or environmental impact studies it provides a flexible general classification to guide initial site selection. Notably this approach can be applied to other regions worldwide with abundant solar and wind resources such as Australia and Northern Africa promoting more effective and sustainable global decision-making for green hydrogen production.
A Numerical Study on Turquoise Hydrogen Production by Catalytic Decomposition of Methane
Feb 2023
Publication
Catalytic decomposition of methane (CDM) is a novel technology for turquoise hydrogen production with solid carbon as the by-product instead of CO2. A computational fluid dynamics model was developed to simulate the CDM process in a 3D fixed bed reactor accounting for the impact of carbon deposition on catalytic activity. The model was validated with experimental data and demonstrated its capability to predict hydrogen concentration and catalyst deactivation time under varying operating temperatures and methane flow rates. The catalyst lifespan was characterized by the maximum carbon yield (i.e. gC/gcat) which is a crucial indicator for determining the cost of hydrogen generation. Parametric studies were performed to analyse the effect of inlet gas composition and operating pressure on CDM performance. Various CH4/H2 ratios were simulated to improve the methane conversion efficiency generating a higher amount of hydrogen while increasing the maximum carbon yield up to 49.5 gC/gcat. Additionally higher operating pressure resulted in higher methane decomposition rates which reflects the nature of the chemical kinetics.
Hydrogen and the Global Energy Transition—Path to Sustainability and Adoption across All Economic Sectors
Feb 2024
Publication
This perspective article delves into the critical role of hydrogen as a sustainable energy carrier in the context of the ongoing global energy transition. Hydrogen with its potential to decarbonize various sectors has emerged as a key player in achieving decarbonization and energy sustainability goals. This article provides an overview of the current state of hydrogen technology its production methods and its applications across diverse industries. By exploring the challenges and opportunities associated with hydrogen integration we aim to shed light on the pathways toward achieving a sustainable hydrogen economy. Additionally the article underscores the need for collaborative efforts among policymakers industries and researchers to overcome existing hurdles and unlock the full potential of hydrogen in the transition to a low-carbon future. Through a balanced analysis of the present landscape and future prospects this perspective article aims to contribute valuable insights to the discourse surrounding hydrogen’s role in the global energy transition.
Experimental Study of a Homogeneous Charge Compression Ignition Engine Using Hydrogen at High-Altitude Conditions
Feb 2024
Publication
One of the key factors of the current energy transition is the use of hydrogen (H2 ) as fuel in energy transformation technologies. This fuel has the advantage of being produced from the most primary forms of energy and has the potential to reduce carbon dioxide (CO2 ) emissions. In recent years hydrogen or hydrogen-rich mixtures in internal combustion engines (ICEs) have gained popularity with numerous reports documenting their use in spark ignition (SI) and compression ignition (CI) engines. Homogeneous charge compression ignition (HCCI) engines have the potential for substantial reductions in nitrogen oxides (NOx) and particulate matter (PM) emissions and the use of hydrogen along with this kind of combustion could substantially reduce CO2 emissions. However there have been few reports using hydrogen in HCCI engines with most studies limited to evaluating technical feasibility combustion characteristics engine performance and emissions in laboratory settings at sea level. This paper presents a study of HCCI combustion using hydrogen in a stationary air-cooled Lombardini 25 LD 425-2 modified diesel engine located at 1495 m above sea level. An experimental phase was conducted to determine the intake temperature requirements and equivalence ratios for stable HCCI combustion. These results were compared with previous research carried out at sea level. To the best knowledge of the authors this is the first report on the combustion and operational limits for an HCCI engine fueled with hydrogen under the mentioned specific conditions. Equivalence ratios between 0.21 and 0.28 and intake temperatures between 188 ◦C and 235 ◦C effectively achieved the HCCI combustion. These temperature values were on average 100 ◦C higher than those reported in previous studies. The maximum value for the indicated mean effective pressure (IMEPn) was 1.75 bar and the maximum thermal efficiency (ITEn) was 34.5%. The achieved results are important for the design and implementation of HCCI engines running solely on hydrogen in developing countries located at high altitudes above sea level.
Recent Progress and Techno-economic Analysis of Liquid Organic Hydrogen Carriers for Australian Renewable Energy Export - A Critical Review
Jan 2024
Publication
Hydrogen as a primary carbon-free energy carrier is confronted by challenges in storage and transportation. However liquid organic hydrogen carriers (LOHCs) present a promising solution for storing and transporting hydrogen at ambient temperature and atmospheric pressure. Unlike circular energy carriers such as methanol ammonia and synthetic natural gas LOHCs do not produce by-products during hydrogen recovery. LOHCs only act as hydrogen carriers and the carriers can also be recycled for reuse. Although there are considerable advantages to LOHCs there are also some drawbacks especially relative to the energy consumption during the dehydrogenation step of the LOHC recycling. This review summarizes the recent progresses in LOHC technologies focusing on catalyst developments process and reactor designs applications and techno-economic assessments (TEA). LOHC technologies can potentially offer significant benefits to Australia especially in terms of hydrogen as an export commodity. LOHCs can help avoid capital costs associated with infrastructure such as transportation vessels while reducing hydrogen loss during transportation such as in the case of liquid hydrogen (LH2). Additionally it minimises CO2 emissions as observed in methane and methanol reforming. Thus it is essential to dedicate more efforts to explore and develop LOHC technologies in the Australian context.
Exergy Analysis in Intensification of Sorption-enhanced Steam Methane Reforming for Clean Hydrogen Production: Comparative Study and Efficiency Optimisation
Feb 2024
Publication
Hydrogen has a key role to play in decarbonising industry and other sectors of society. It is important to develop low-carbon hydrogen production technologies that are cost-effective and energy-efficient. Sorption-enhanced steam methane reforming (SE-SMR) is a developing low-carbon (blue) hydrogen production process which enables combined hydrogen production and carbon capture. Despite a number of key benefits the process is yet to be fully realised in terms of efficiency. In this work a sorption-enhanced steam methane reforming process has been intensified via exergy analysis. Assessing the exergy efficiency of these processes is key to ensuring the effective deployment of low-carbon hydrogen production technologies. An exergy analysis was performed on an SE-SMR process and was then subsequently used to incorporate process improvements developing a process that has theoretically an extremely high CO2 capture rate of nearly 100 % whilst simultaneously demonstrating a high exergy efficiency (77.58 %) showcasing the potential of blue hydrogen as an effective tool to ensure decarbonisation in an energy-efficient manner.
Techno-Economic Analysis of Hydrogen Production from Swine Manure Biogas via Steam Reforming in Pilot-Scale Installation
Sep 2023
Publication
The main purpose of this paper is the techno-economic analysis of hydrogen production from biogas via steam reforming in a pilot plant. Process flow modeling based on mass and energy balance is used to estimate the total equipment purchase and operating costs of hydrogen production. The pilot plant installation produced 250.67 kg/h hydrogen from 1260 kg/h biomethane obtained after purification of 4208 m3/h biogas using a heat and mass integration process. Despite the high investment cost the plant shows a great potential for biomethane reduction and conversion to hydrogen an attractive economic path with ecological possibilities. The conversion of waste into hydrogen is a possibility of increasing importance in the global energy economy. In the future such a plant will be expanded with a CO2 reduction module to increase economic efficiency and further reduce greenhouse gases in an economically viable manner.
Environmental Implications and Levelized Cost Analysis of E-fuel Production under Photovoltaic Energy, Direct Air Capture, and Hydrogen
Jan 2024
Publication
The ecological transition in the transport sector is a major challenge to tackle environmental pollution and European legislation will mandate zero-emission new cars from 2035. To reduce the impact of petrol and diesel vehicles much emphasis is being placed on the potential use of synthetic fuels including electrofuels (e-fuels). This research aims to examine a levelised cost (LCO) analysis of e-fuel production where the energy source is renewable. The energy used in the process is expected to come from a photovoltaic plant and the other steps required to produce e-fuel: direct air capture electrolysis and Fischer-Tropsch process. The results showed that the LCOe-fuel in the baseline scenario is around 3.1 €/l and this value is mainly influenced by the energy production component followed by the hydrogen one. Sensitivity scenario and risk analyses are also conducted to evaluate alternative scenarios and it emerges that in 84% of the cases LCOe-fuel ranges between 2.8 €/l and 3.4 €/l. The findings show that the current cost is not competitive with fossil fuels yet the development of e-fuels supports environmental protection. The concept of pragmatic sustainability incentive policies technology development industrial symbiosis economies of scale and learning economies can reduce this cost by supporting the decarbonisation of the transport sector.
Willingness of Chinese Households to Pay Extra for Hydrogen-fuelled Buses: A Survey Based on Willingness to Pay
Mar 2023
Publication
Hydrogen-fuelled buses play an important role in the construction of low-carbon cities as a means of green travel. Beijing as a pilot city of hydrogen-fuelled buses in China is very important in the promotion of hydrogen-fuelled buses in China. Unfortunately the public acceptance of hydrogen-fuelledfuelled buses and their environmental positive externality value have not been studied. In this paper we investigated the willingness of Beijing households to pay for the promotion of hydrogen-fuelled buses and its influencing factors by means of a web-based questionnaire. The spike model was also used to estimate the willingness to pay (WTP) for hydrogen buses. The results show that the WTP of Beijing households is CNY 3.19 per trip. The value of a positive environmental externality is approximately CNY 29.15 million per trip. Household income level environmental knowledge individual environmental ethics and perceived behavioural control are the main influencing factors of WTP. Therefore policymakers should strengthen publicity efforts to increase individuals’ environmental awareness and environmental ethics and optimize the layout of hydrogen-fuelled bus schedules and riding experiences to improve individuals’ perceptual and behaviour control. Finally the positive environmental externality value of hydrogen buses should be valued which will help increase investor interest.
Global Hydrogen and Synfuel Exchanges in an Emission-Free Energy System
Apr 2023
Publication
This study investigates the global allocation of hydrogen and synfuels in order to achieve the well below 2 ◦C preferably 1.5 ◦C target set in the Paris Agreement. For this purpose TIMES Integrated Assessment Model (TIAM) a global energy system model is used. In order to investigate global hydrogen and synfuel flows cost potential curves are aggregated and implemented into TIAM as well as demand technologies for the end use sectors. Furthermore hydrogen and synfuel trades are established using liquid hydrogen transport (LH2 ) and both new and existing technologies for synfuels are implemented. To represent a wide range of possible future events four different scenarios are considered with different characteristics of climate and security of supply policies. The results show that in the case of climate policy the renewable energies need tremendous expansion. The final energy consumption is shifting towards the direct use of electricity while certain demand technologies (e.g. aviation and international shipping) require hydrogen and synfuels for full decarbonization. Due to different security of supply policies the global allocation of hydrogen and synfuel production and exports is shifting while the 1.5 ◦C target remains feasible in the different climate policy scenarios. Considering climate policy Middle East Asia is the preferred region for hydrogen export. For synfuel production several regions are competitive including Middle East Asia Mexico Africa South America and Australia. In the case of security of supply policies Middle East Asia is sharing the export volume with Africa while only minor changes can be seen in the synfuel supply.
The Transition to a Renewable Energy Electric Grid in the Caribbean Island Nation of Antigua and Barbuda
Aug 2023
Publication
The present study describes the development and application of a model of the national electricity system for the Caribbean dual-island nation of Antigua and Barbuda to investigate the cost optimal mix of solar photovoltaics (PVs) wind and in the most novel contribution concentrating solar power (CSP). These technologies together with battery and hydrogen energy storage can enable the aim of achieving 100% renewable electricity and zero carbon emissions. The motivation for this study was that while most nations in the Caribbean rely largely on diesel fuel or heavy fuel oil for grid electricity generation many countries have renewable resources beyond wind and solar energy. Antigua and Barbuda generates 93% of its electricity from diesel-fueled generators and has set the target of becoming a net-zero nation by 2040 as well as having 86% renewable energy generation in the electricity sector by 2030 but the nation has no hydroelectric or geothermal resources. Thus this study aims to demonstrate that CSP is a renewable energy technology that can help assist Antigua and Barbuda in its transition to a renewable energy electric grid while also decreasing electricity generation costs. The modeled optimal mix of renewable energy technologies presented here was found for Antigua and Barbuda by assessing the levelized cost of electricity (LCOE) for systems comprising various combinations of energy technologies and storage. Other factors were also considered such as land use and job creation. It was found that 100% renewable electricity systems are viable and significantly less costly than current power systems and that there is no single defined pathway towards a 100% renewable energy grid but several options are available.
Proactive Emergency Response Strategies for First Responders to Hydrogen Gas Leakages in Vehicles
Feb 2024
Publication
The widespread use of fossil fuels in automobiles has become a concern particularly in light of recent frequent natural disasters prompting a shift towards eco-friendly vehicles to mitigate greenhouse gas emissions. This shift is evident in the rapidly increasing registration rates of hydrogen vehicles. However with the growing presence of hydrogen vehicles on roads a corresponding rise in related accidents is anticipated posing new challenges for first responders. In this study computational fluid dynamics analysis was performed to develop effective response strategies for first responders dealing with high-pressure hydrogen gas leaks in vehicle accidents. The analysis revealed that in the absence of blower intervention a vapor cloud explosion from leaked hydrogen gas could generate overpressure exceeding 13.8 kPa potentially causing direct harm to first responders. In the event of a hydrogen vehicle accident requiring urgent rescue activities the appropriate response strategy must be selected. The use of blowers can aid in developing a variety of strategies by reducing the risk of a vapor cloud explosion. Consequently this study offers a tailored response strategy for first responders in hydrogen vehicle leak scenarios emphasizing the importance of situational assessment at the incident site.
Research on Fast Frequency Response Control Strategy of Hydrogen Production Systems
Mar 2024
Publication
With the large-scale integration of intermittent renewable energy generation presented by wind and photovoltaic power the security and stability of power system operations have been challenged. Therefore this article proposes a control strategy of a hydrogen production system based on renewable energy power generation to enable the fast frequency response of a grid. Firstly based on the idea of virtual synchronous control a fast frequency response control transformation strategy for the grid-connected interface of hydrogen production systems for renewable energy power generation is proposed to provide active power support when the grid frequency is disturbed. Secondly based on the influence of VSG’s inertia and damping coefficient on the dynamic characteristics of the system a VSG adaptive control model based on particle swarm optimization is designed. Finally based on the Matlab/Simulink platform a grid-connected simulation model of hydrogen production systems for renewable energy power generation is established. The results show that the interface-transformed electrolytic hydrogen production device can actively respond to the frequency disturbances of the power system and participate in primary frequency control providing active support for the frequency stability of the power system under high-percentage renewable energy generation integration. Moreover the system with parameter optimization has better fast frequency response control characteristics.
Advancing the Affordable and Clean Energy in Large Energy-consuming Economies: The Role of Green Transition, Complexity-based, and Geostrategy Policy
Aug 2023
Publication
With decreasing costs of the clean technologies the balanced scales of the Sustainable Development Goal 7 targets e.g. energy equity (EE) energy security (ES) and environmental sustainability (EVS) are quickly changing. This fundamental balancing process is a key requirement for a net-zero future. Accordingly this research analyzes the regime-switching effect of Hydrogen economy as the green transition sharing economy and economic complexity as the complexity-based and geopolitical risks and energy prices as the geostrategy policies on the Goal 7 targets. To this end a Markov-switching panel vector autoregressive method with regime-heteroskedasticity is applied to study advancing the Goal 7 in the world's twenty-five large energy consumers during 2004–2020. Concerning the parameters and statistics of the model the results refer to the existence of two regimes associated with the Goal 7 corners called “upward and downward” regimes for EE and “slightly upward and sharply upward” regimes for ES and EVS. It is revealed that the vulnerability of EE and ES targets is considerably reduced when the regime switches to the dominant regime that is “downward” and “slightly upward” regimes respectively and that of the EVS target remains unaffected. Through the impulse-response analysis the findings denote that the first hypothesis of the efficiency of the Hydrogen economy in promoting the Goal 7 targets is insignificant. However the significant short-term and dynamic shock effects of the complexity-based and geostrategy policies on the Hydrogen economy are detected which will be a feasible alternative assessment in advancing the Goal 7. Further the complexity-based policies support the Goal 7 targets under different regimes especially in the short- and medium-term. Hence the second hypothesis regarding the effectiveness of the complexity-based policies in promoting Goal 7 targets is confirmed. The third hypothesis concerning the complexity of the impact of geostrategy policies on the Goal 7 targets is verified. Particularly the switching process towards the Goal 7 may not necessarily be restricted by the geopolitical risks. Moreover EE is supported through energy prices in the short-term under both regimes while they are non-conductive to promote ES and EVS through time. Accordingly the decision-makers should acknowledge adopting a regime-switching path forward for ensuring the time-varying balanced growth of the Goal 7 targets as the impact of the suggested policy instruments is asymmetric.
Near-term Infrastructure Rollout and Investment Strategies for Net-zero Hydrogen Supply Chains
Feb 2024
Publication
Low-carbon hydrogen plays a key role in European industrial decarbonization strategies. This work investigates the cost-optimal planning of European low-carbon hydrogen supply chains in the near term (2025–2035) comparing several hydrogen production technologies and considering multiple spatial scales. We focus on mature hydrogen production technologies: steam methane reforming of natural gas biomethane reforming biomass gasification and water electrolysis. The analysis includes carbon capture and storage for natural gas and biomass-derived hydrogen. We formulate and solve a linear optimization model that determines the costoptimal type size and location of hydrogen production and transport technologies in compliance with selected carbon emission targets including the EU fit for 55 target and an ambitious net-zero emissions target for 2035. Existing steam methane reforming capacities are considered and optimal carbon and biomass networks are designed. Findings identify biomass-based hydrogen production as the most cost-efficient hydrogen technology. Carbon capture and storage is installed to achieve net-zero carbon emissions while electrolysis remains costdisadvantageous and is deployed on a limited scale across all considered sensitivity scenarios. Our analysis highlights the importance of spatial resolution revealing that national perspectives underestimate costs by neglecting domestic transport needs and regional resource constraints emphasizing the necessity for highly decarbonized infrastructure designs aligned with renewable resource availabilities.
Optimal Multi-layer Economical Schedule for Coordinated Multiple Mode Operation of Wind-solar Microgrids with Hybrid Energy Storage Systems
Nov 2023
Publication
The aim of this paper is the design and implementation of an advanced model predictive control (MPC) strategy for the management of a wind–solar microgrid (MG) both in the islanded and grid-connected modes. The MG includes energy storage systems (ESSs) and interacts with external hydrogen and electricity consumers as an extra feature. The system participates in two different electricity markets i.e. the daily and real-time markets characterized by different time-scales. Thus a high-layer control (HLC) and a low-layer control (LLC) are developed for the daily market and the real-time market respectively. The sporadic characteristics of renewable energy sources and the variations in load demand are also briefly discussed by proposing a controller based on the stochastic MPC approach. Numerical simulations with real wind and solar generation profiles and spot prices show that the proposed controller optimally manages the ESSs even when there is a deviation between the predicted scenario determined at the HLC and the real-time one managed by the LLC. Finally the strategy is tested on a lab-scale MG set up at Khalifa University Abu Dhabi UAE.
Review of the Status and Prospects of Fiber Optic Hydrogen Sensing Technology
Aug 2023
Publication
With the unprecedented development of green and renewable energy sources the proportion of clean hydrogen (H2 ) applications grows rapidly. Since H2 has physicochemical properties of being highly permeable and combustible high-performance H2 sensors to detect and monitor hydrogen concentration are essential. This review discusses a variety of fiber-optic-based H2 sensor technologies since the year 1984 including: interferometer technology fiber grating technology surface plasma resonance (SPR) technology micro lens technology evanescent field technology integrated optical waveguide technology direct transmission/reflection detection technology etc. These technologies have been evolving from simply pursuing high sensitivity and low detection limits (LDL) to focusing on multiple performance parameters to match various application demands such as: high temperature resistance fast response speed fast recovery speed large concentration range low cross sensitivity excellent long-term stability etc. On the basis of palladium (Pd)-sensitive material alloy metals catalysts or nanoparticles are proposed to improve the performance of fiberoptic-based H2 sensors including gold (Au) silver (Ag) platinum (Pt) zinc oxide (ZnO) titanium oxide (TiO2 ) tungsten oxide (WO3 ) Mg70Ti30 polydimethylsiloxane (PDMS) graphene oxide (GO) etc. Various microstructure processes of the side and end of optical fiber H2 sensors are also discussed in this review.
Multi-criteria Optimisation of Fermentative and Solar-driven Electrolytic Hydrogen and Electricity Supply-demand Network with Hybrid Storage System
May 2023
Publication
Harnessing renewable resources such as solar energy and biogenic waste for hydrogen production offers a path toward a carbon-neutral industrial economy. This study suggests the development of a renewable-based hydrogen and power supply facility (HPSF) that relies on fermentation and solar-driven electrolysis technologies to achieve penetration of renewable hydrogen and electricity in the industrial symbiosis. Literature studies reported that the hybrid battery-hydrogen storage system could effectively improve the sustainability and reliability of renewable energy supplies yet its application under diurnal and seasonal renewable resource variations has not been well studied. Hence this work develops a multi-criteria optimisation framework for the configuration design of the proposed HPSF that concurrently targets industrial hydrogen and electrical loads with the consideration of diurnal and seasonal renewable resource variations. Case scenarios with different storage applications are presented to evaluate the role of storage in improving economic and environmental sustainability. The results show that the application of hybrid storage with molten carbonate fuel cell (MCFC) systems is preferred from a comprehensive sustainability standpoint which improves the sustainability-weighted return-on investment metric (SWROIM) score by 4%/yr compared to HPSF without storage application. On the other hand the application of a single-battery system is the most economical solution with a return on investment (ROI) of 0.7%/yr higher than the hybrid storage approach. The research outcome could provide insights into the integration of fermentative and solar-driven electrolytic hydrogen production technologies into the industrial symbiosis to further enhance a sustainable economy.
Electrolyzer Array Alternate Control Strategy Considering Wind Power Prediction
Aug 2022
Publication
Non grid connected wind power hydrogen production technology is of great significance for the large-scale comprehensive utilization of hydrogen energy and accelerating the development of clean energy. In this paper an electrolyzer power allocation and alternate control method for non grid connected wind power hydrogen production is proposed and the optimized control strategy are combined to predict the maximum wind power of certain time interval. While retaining the required data characteristics the instantaneous fluctuation of some wind power data is eliminated which provides a reliable basis for power distribution in the alternation control strategy of electrolyzer array. The case simulation verifies the effectiveness of the electrolyzer array control principle and the prediction of the maximum wind power. While ensuring the absorption effect and hydrogen production rate the service life and operation safety of the electrolyzer array are effectively improved by balancing the working state of each electrolyzer.
Impacts of Green Energy Expansion and Gas Import Reduction on South Korea’s Economic Growth: A System Dynamics Approach
Jun 2023
Publication
South Korea ranking ninth among the largest energy consumers and seventh in carbon dioxide emissions from 2016 to 2021 faces challenges in energy security and climate change mitigation. The primary challenge lies in transitioning from fossil fuel dependency to a more sustainable and diversified energy portfolio while meeting the growing energy demand for continued economic growth. This necessitates fostering innovation and investment in the green energy sector. This study examines the potential impact of green energy expansion (through integrating renewable energy and hydrogen production) and gas import reduction on South Korea’s economic growth using a system dynamics approach. The findings indicate that increasing investment in green energy can result in significant growth rates ranging from 7% to 35% between 2025 and 2040. Under the expansion renewable energy scenario (A) suggests steady but sustainable economic growth in the long term while the gas import reduction scenario (B) displays a potential for rapid economic growth in the short term with possible instability in the long term. The total production in Scenario B is USD 2.7 trillion in 2025 and will increase to USD 4.8 trillion by 2040. Scenario C which combines the effects of both Scenarios A and B results in consistently high economic growth rates over time and a substantial increase in total production by 2035–2040 from 20% to 46%. These findings are critical for policymakers in South Korea as they strive for sustainable economic growth and transition to renewable energy.
A Simulation Study on Evaluating the Influence of Impurities on Hydrogen Production in Geological Carbon Dioxide Storage
Sep 2023
Publication
In this study we examined the effect of CO2 injection into deep saline aquifers considering impurities present in blue hydrogen production. A fluid model was designed for reservoir conditions with impurity concentrations of 3.5 and 20%. The results showed that methane caused density decreases of 95.16 and 76.16% at 3.5 and 20% respectively whereas H2S caused decreases of 99.56 and 98.77% respectively. Viscosity decreased from 0.045 to 0.037 cp with increasing methane content up to 20%; however H2S did not affect the viscosity. Notably CO2 with H2S impacted these properties less than methane. Our simulation model was based on the Gorae-V properties and simulated injections for 10 years followed by 100 years of monitoring. Compared with the pure CO2 injection methane reached its maximum pressure after eight years and eleven months at 3.5% and eight years at 20% whereas H2S reached maximum pressure after nine years and two months and nine years and six months respectively. These timings affected the amount of CO2 injected. With methane as an impurity injection efficiency decreased up to 73.16% whereas with H2S it decreased up to 81.99% with increasing impurity concentration. The efficiency of CO2 storage in the dissolution and residual traps was analyzed to examine the impact of impurities. The residual trap efficiency consistently decreased with methane but increased with H2S. At 20% concentration the methane trap exhibited higher efficiency at the end of injection; however H2S had a higher efficiency at the monitoring endpoint. In carbon capture and storage projects methane impurities require removal whereas H2S may not necessitate desulfurization due to its minimal impact on CO2 storage efficiency. Thus the application of carbon capture and storage (CCS) to CO2 emissions containing H2S as an impurity may enable economically viable operations by reducing additional costs.
Can an Energy Only Market Enable Resource Adequacy in a Decarbonized Power System? A Co-simulation with Two Agent-based-models
Feb 2024
Publication
Future power systems in which generation will come almost entirely from variable Renewable Energy Sources (vRES) will be characterized by weather-driven supply and flexible demand. In a simulation of the future Dutch power system we analyze whether there are sufficient incentives for market-driven investors to provide a sufficient level of security of supply considering the profit-seeking and myopic behavior of investors. We cosimulate two agent-based models (ABM) one for generation expansion and one for the operational time scale. The results suggest that in a system with a high share of vRES and flexibility prices will be set predominantly by the demand’s willingness to pay particularly by the opportunity cost of flexible hydrogen electrolyzers. The demand for electric heating could double the price of electricity in winter compared to summer and in years with low vRES could cause shortages. Simulations with stochastic weather profiles increase the year-to-year variability of cost recovery by more than threefold and the year-to-year price variability by more than tenfold compared to a scenario with no weather uncertainty. Dispatchable technologies have the most volatile annual returns due to high scarcity rents during years of low vRES production and diminished returns during years with high vRES production. We conclude that in a highly renewable EOM investors would not have sufficient incentives to ensure the reliability of the system. If they invested in such a way to ensure that demand could be met in a year with the lowest vRES yield they would not recover their fixed costs in the majority of years.
Top Level Design and Evaluation of Advanced Low/zero Carbon Fuel Ships Power Technology
Oct 2022
Publication
The greenhouse effect has always been a problem troubling various country many fields have made corresponding technological improvements and regulations and the shipping industry is no exception. In the shipping field governments are actively looking for viable low-carbon/zero-carbon alternative fuels to reduce their dependence on traditional fossil fuels. This paper discusses the challenges and opportunities of replacing fuel oil with clean energies. Firstly the alternative fuels that have been proposed frequently and widely in recent years are summarized and their sources adaptive power systems and relationships among fuels are systematically summarized. Secondly when evaluating the advantages and future development trends of each energy the environmental economic and safety factors are digitally quantified. Results show that the analysis focuses on the efficiency and economics of carbon reduction. Hydrogen ammonia and nuclear energy show advantages in environmental quantification factors while LNG biofuels and alcohols show benefits in economic quantification factors considering calorific value and fuel price and LNG and alcohols received high scores in safety assessment. Finally the study predicts the evolution and development trend of ship fuels in the future and evaluates the most suitable energy for ship development in different periods.
Open-source Project Feasibility Tools for Supporting Development of the Green Ammonia Value Chain
Nov 2022
Publication
Ammonia plays a vital role in feeding the world through fertilizer production as well as having other industrial uses. However current ammonia production processes rely heavily on fossil fuels mostly natural gas to generate hydrogen as a feedstock. There is an urgent need to re-design and decarbonise the production process to reduce greenhouse emissions and avoid dependence on volatile gas markets and a depleting resource base. Renewable energy driven electrolysis to generate hydrogen provides a viable pathway for producing carbon-free or green ammonia. However a key challenge associated with producing green ammonia is managing low cost but highly variable wind and solar renewable energy generation for hydrogen electrolysis while maintaining reliable operation of the less flexible ammonia synthesis unit. To date green ammonia production has only been demonstrated at pilot scale and optimising plant configurations and scaling up production facilities is an urgent task. Existing feasibility studies have demonstrated the ability to model and cost green ammonia production pathways that can overcome the technical and economic challenges. However these existing approaches are context specific demonstrating the ability to model and cost green ammonia production for defined locations with set configurations. In this paper we present a modelling framework that consolidates the array of configurations previously studied into a single framework that can be tailored to the location of interest. Our open-source green ammonia modelling and costing tool dynamically simulates the integration of renewable energy with a wide range of balancing power and storage options to meet the flexible demands of the green ammonia production process at hourly time resolution over a year or more. Unlike existing models the open-source implementation of our tool allows it to be used by a potentially wide range of stakeholders to explore their own projects and help guide the upscaling of green ammonia as a pathway for decarbonisation. Using Gladstone in Australia as a case study a 1 million tonne per annum (MMTPA) green ammonia plant is modelled and costed using price assumptions for major equipment in 2030 provided by the Australian Energy Market Operator (AEMO). Using a hybrid (solar PV and wind) renewable energy source and Battery Energy Storage System as balancing technology we estimate a levelized cost of ammonia (LCOA) between 0.69 and 0.92 USD kgNH3 -1 . While greater than historical ammonia production costs from natural gas falling renewables costs and emission reduction imperatives suggest a major future role for green ammonia.
Configuration Optimization of Hydrogen-Based Multi-Microgrid Systems under Electricity Market Trading and Different Hydrogen Production Strategies
Apr 2023
Publication
Hydrogen-based multi-microgrid systems (HBMMSs) are beneficial for energy saving and emission reductions. However the optimal sizing of HBMMSs lacks a practical configuration optimization model and a reasonable solution method. To address these problems we designed a novel structure of HBMMSs that combines conventional energy renewable energy and a hydrogen energy subsystem. Then we established a bi-level multi-objective capacity optimization model while considering electricity market trading and different hydrogen production strategies. The objective of the inner model which is the minimum annual operation cost and the three objectives of the outer model which are the minimum total annual cost (TAC); the annual carbon emission (ACE); and the maximum self-sufficiency rate (SSR) are researched simultaneously. To solve the above optimization model a two-stage solution method which considers the conflicts between objectives and the objectivity of objective weights is proposed. Finally a case study is performed. The results show that when green hydrogen production strategies are adopted the three objectives of the best configuration optimization scheme are USD 404.987 million 1.106 million tons and 0.486 respectively.
International Competitiveness of Low-carbon Hydrogen Supply to the Northwest European Market
Oct 2022
Publication
This paper analyses which sources of low-carbon hydrogen for the Northwest European market are most competitive taking into account costs of local production conversion and transport. Production costs of electrolysis are strongly affected by local renewable electricity costs and capacity factors. Transport costs are the lowest by pipelines for distances under 10000 km with costs linearly increasing with distance. For larger distances transport as ammonia is more efficient with less relation to distance despite higher conversion costs. The most competitive low-carbon hydrogen supply to the Northwest European market appears to be local Steam Methane Reforming with Carbon Capture and Storage when international gas prices return back to historical levels. When gas prices however remain high then import from Morocco with electrolysis directly connected to offshore wind generation is found to be the most competitive source of low-carbon hydrogen. These conclusions are robust for various assumptions on costs and capacity factors.
Nuclear-Renewable Hybrid Energy System with Load Following for Fast Charging Stations
May 2023
Publication
The transportation sector is a significant source of greenhouse gas emissions. Electric vehicles (EVs) have gained popularity as a solution to reduce emissions but the high load of charging stations poses a challenge to the power grid. Nuclear-Renewable Hybrid Energy Systems (N-RHES) present a promising alternative to support fast charging stations reduce grid dependency and decrease emissions. However the intermittent problem of renewable energy sources (RESs) limits their application and the synergies among different technologies have not been fully exploited. This paper proposes a predictive and adaptive control strategy to optimize the energy management of N-RHES for fast charging stations considering the integration of nuclear photovoltaics and wind turbine energy with a hydrogen storage fuel cell system. The proposed dynamic model of a fast-charging station predicts electricity consumption behavior during charging processes generating probabilistic forecasting of electricity consumption time-series profiling. Key performance indicators and sensitivity analyses illustrate the practicability of the suggested system which offers a comprehensive solution to provide reliable sustainable and low-emission energy to fast-charging stations while reducing emissions and dependency on the power grid.
A Study on the Viability of Fuel Cells as an Alternative to Diesel Fuel Generators on Ships
Jul 2023
Publication
This study investigates methods for reducing air pollution in the shipping sector particularly in port areas. The study examines the use of fuel cells as an alternative to diesel generators. Environmental pollution at ports remains a critical issue so using fuel cells as an alternative to conventional energy systems warrants further research. This study compares commercial fuel cell types that can be used on a case study very large crude carrier (VLCC) vessel specifically although the technology is applicable to other vessels and requirements. Seven different fuel cell types were ranked based on five criteria to accomplish this. The proton-exchange membrane cell type was found to be the most suitable fuel cell type for the case study vessel. Based on the input fuel ammonia-based hydrogen storage has been identified as the most promising option along with using an ammonia reforming unit to produce pure hydrogen. Furthermore this study provides an integrated fuel cell module and highlights the economic environmental and maintenance aspects of implementing the proton-exchange membrane fuel cell module for this case study. It also calculates the required space as a crucial constraint of implementing fuel cell technology at sea.
Identifying Informed Beliefs about Hydrogen Technologies Across the Energy Supply Chain
Apr 2023
Publication
Developing a thriving hydrogen industry will depend on public and community support. Past research mainly focusing on the acceptance of hydrogen fuelling stations and cars suggests that people generally support hydrogen energy technology (HET). Few studies have however considered how people think about other components of the hydrogen supply chain (i.e. technologies required to make store transport and use hydrogen). Moreover there has been limited research investigating how people interpret and develop beliefs about HET after being presented with technical information. This paper attempts to address these research gaps by presenting the findings from four face-to-face focus group discussions conducted in Australia. The findings suggest that people have differing views about HET which depends on the type of technology and these views influence levels of support. The study also revealed concerns about a range of other factors that have yet to be considered in hydrogen acceptance research (e.g. perceived water use efficiency and indirect benefits). The findings highlight the value of qualitative research for identifying salient beliefs that shape attitudes towards HET and provide recommendations for future research and how to effectively communicate with the public and communities about an emerging hydrogen industry.
Prospects and Challenges of Green Hydrogen Economy via Multi-Sector Global Symbiosis in Qatar
Jan 2021
Publication
Low carbon hydrogen can be an excellent source of clean energy which can combat global climate change and poor air quality. Hydrogen based economy can be a great opportunity for a country like Qatar to decarbonize its multiple sectors including transportation shipping global energy markets and industrial sectors. However there are still some barriers to the realization of a hydrogen-based economy which includes large scale hydrogen production cost infrastructure investments bulk storage transport & distribution safety consideration and matching supply-demand uncertainties. This paper highlights how the aforementioned challenges can be handled strategically through a multi-sector industrial-urban symbiosis for the hydrogen supply chain implementation. Such symbiosis can enhance the mutual relationship between diverse industries and urban planning by exploring varied scopes of multi-purpose hydrogen usage (i.e. clean energy source as a safer carrier industrial feedstock and intermittent products vehicle and shipping fuel and international energy trading etc.) both in local and international markets. It enables individual entities and businesses to participate in the physical exchange of materials by-products energy and water with strategic advantages for all participants. Besides waste/by-product exchanges several different kinds of synergies are also possible such as the sharing of resources and shared facilities. The diversified economic base regional proximity and the facilitation of rules strategies and policies may be the key drivers that support the creation of a multi-sector hydrogen supply chain in Qatar.
Hydrogen Informed Gurson Model for Hydrogen Embrittlement Simulation
Jul 2019
Publication
Hydrogen-microvoid interactions were studied via unit cell analyses with different hydrogen concentrations. The absolute failure strain decreases with hydrogen concentration but the failure loci were found to follow the same trend dependent only on stress triaxiality in other words the effects of geometric constraint and hydrogen on failure are decoupled. Guided by the decoupling principle a hydrogen informed Gurson model is proposed. This model is the first practical hydrogen embrittlement simulation tool based on the hydrogen enhanced localized plasticity (HELP) mechanism. It introduces only one additional hydrogen related parameter into the Gurson model and is able to capture hydrogen enhanced internal necking failure of microvoids with accuracy; its parameter calibration procedure is straightforward and cost efficient for engineering purpose
An Improved State Machine-based Energy Management Strategy for Renewable Energy Microgrid with Hydrogen Storage System
Oct 2022
Publication
Renewable energy (solar and wind) sources have evolved dramatically in recent years around the globe primarily because they have the potential to generate environmentally friendly energy. However operating systems with high renewable energy penetration remain challenging due to the stochastic nature of these energy sources. To tackle these problems the authors propose a state machine-based energy management strategy combined with a hysteresis band control strategy for renewable energy hybrid microgrids that integrates hydrogen storage systems. By considering the power difference between the renewable energy source and the demand the battery’s state of charge and the hydrogen storage level the proposed energy management strategy can control the power of fuel cells electrolyzers and batteries in a microgrid and the power imported into/exported from the main grid. The results showed that the energy management strategy provides the following advantages: (1) the power supply and demand balance in the microgrid was balanced (2) the lifespans of the electrolyzer and fuel cell were extended and (3) the state of charge of the battery and the stored level of the hydrogen were appropriately ensured.
Tourist Preferences for Fuel Cell Vehicle Rental: Going Green with Hydrogen on the Island of Tenerife
Mar 2023
Publication
Using a discrete choice experiment (DCE) a survey of international tourists on the island of Tenerife is conducted to examine preferences for fuel cell vehicle (FCV) rental while on vacation. Survey respondents were generally supportive of FCVs and willing to hire one as part of their trip but for most individuals this is contingent on an adequate fuel station infrastructure. A latent class model was used to identify three distinct groups; one of which potentially represent early adopters e they have a high willingness-to-pay (WTP) for green hydrogen and are more likely to accept a low number of fuel stations but it could be challenging to convince them to use FCVs if they are not run on green hydrogen.
Green Hydrogen Production through Ammonia Decomposition Using Non-Thermal Plasma
Sep 2023
Publication
Liquid hydrogen carriers will soon play a significant role in transporting energy. The key factors that are considered when assessing the applicability of ammonia cracking in large-scale projects are as follows: high energy density easy storage and distribution the simplicity of the overall process and a low or zero-carbon footprint. Thermal systems used for recovering H2 from ammonia require a reaction unit and catalyst that operates at a high temperature (550–800 ◦C) for the complete conversion of ammonia which has a negative effect on the economics of the process. A non-thermal plasma (NTP) solution is the answer to this problem. Ammonia becomes a reliable hydrogen carrier and in combination with NTP offers the high conversion of the dehydrogenation process at a relatively low temperature so that zero-carbon pure hydrogen can be transported over long distances. This paper provides a critical overview of ammonia decomposition systems that focus on non-thermal methods especially under plasma conditions. The review shows that the process has various positive aspects and is an innovative process that has only been reported to a limited extent.
Recent Progress in Conducting Polymers for Hydrogen Storage and Fuel Cell Applications
Oct 2020
Publication
Hydrogen is a clean fuel and an abundant renewable energy resource. In recent years huge scientific attention has been invested to invent suitable materials for its safe storage. Conducting polymers has been extensively investigated as a potential hydrogen storage and fuel cell membrane due to the low cost ease of synthesis and processability to achieve the desired morphological and microstructural architecture ease of doping and composite formation chemical stability and functional properties. The review presents the recent progress in the direction of material selection modification to achieve appropriate morphology and adsorbent properties chemical and thermal stabilities. Polyaniline is the most explored material for hydrogen storage. Polypyrrole and polythiophene has also been explored to some extent. Activated carbons derived from conducting polymers have shown the highest specific surface area and significant storage. This review also covers recent advances in the field of proton conducting solid polymer electrolyte membranes in fuel cells application. This review focuses on the basic structure synthesis and working mechanisms of the polymer materials and critically discusses their relative merits.
CFD Modelling of Hydrogen and Hydrogen-methane Explosions - Analysis of Varying Concentration and Reduced Oxygen Atmospheres
Feb 2023
Publication
This paper evaluates the predictive capabilities of the advanced consequence model FLACS-CFD for deflagrations involving hydrogen. Two modelling approaches are presented: the extensively validated model system originally developed for hydrocarbons included in FLACS-CFD 22.1 and a Markstein number dependent model implemented in the in-house version FLACS-CFD 22.1 IH. The ability of the models to predict the overpressure and the flame arrival time for scenarios with different concentrations of hydrogen and thus different Lewis and Markstein numbers is assessed. Furthermore the effect of adding methane or nitrogen on overpressure for different regimes of premixed combustion are investigated. The validation dataset includes deflagrations in the open or in congested open areas and vented deflagrations in empty or congested enclosures. The overpressure predictions by FLACS-CFD 22.1 IH are found to be more accurate than those obtained with FLACS-CFD 22.1 for scenarios with varying hydrogen concentrations and/or added nitrogen or methane in the mixture. The predictions by FLACS-CFD 22.1 IH for lean hydrogen mixtures are within a factor of 2 of the values observed in the experiments. Further development of the model is needed for more accurate prediction of deflagrations involving rich hydrogen mixtures as well as scenarios with other fuels and/or conditions where the initial pressure or temperature deviate significantly from ambient conditions.
Fuelling the Transition Podcast: Using Hydrogen to Achieve Net-zero
Jan 2021
Publication
In order to achieve the EU’s target of 55% carbon reduction by 2030 hydrogen will have to make a key contribution to the energy mix. With many applications in industrial heat mobility power and chemical refineries hydrogen can be used to decarbonise where electrification is not possible. Equinor is a broad energy company with 21000 employees developing oil gas wind and solar energy in more than 30 countries worldwide. Equinor have been at the forefront of promoting hydrogen projects in Europe and developing low-carbon hydrogen solutions. In this episode Johan Leuraers Chief Consultant - Policy and Regulatory Affairs at Equinor and John Williams Head of Hydrogen Expertise Cluster at AFRY Management Consulting join us to discuss the main barriers to the uptake of hydrogen and the next steps to kick-start the hydrogen economy.
The podcast can be found on their website.
The podcast can be found on their website.
Optimal Scheduling of Multi-microgrids with Power to Hydrogen Considering Federated Demand Response
Sep 2022
Publication
Hydrogen is regarded as a promising fuel in the transition to clean energy. Nevertheless as the demand for hydrogen increases some microgrids equipped with P2H (MGH) will encounter the issue of primary energy deficiency. Meanwhile some microgrids (MGs) face the difficulty of being unable to consume surplus energy locally. Hence we interconnect MGs with different energy characteristics and then establish a collaborative scheduling model of multi-microgrids (MMGs). In this model a federated demand response (FDR) program considering predictive mean voting is designed to coordinate controllable loads of electricity heat and hydrogen in different MGs. With the coordination of FDR the users’ satisfaction and comfort in each MG are kept within an acceptable range. To further adapt to an actual working condition of the microturbine (MT) in MGH a power interaction method is proposed to maintain the operating power of the MT at the optimum load level and shave peak and shorten the operating periods of MT. In the solution process the sequence operation theory is utilized to deal with the probability density of renewable energy. A series of case studies on a test system of MMG demonstrate the effectiveness of the proposed method.
Exploring Technological Solutions for Onboard Hydrogen Storage Systems Through a Heterogeneous Knowledge Network: From Current State to Future Research Opportunities
Jun 2022
Publication
With the imminent threat of the energy crises innovation in energy technologies is happening world-wide. The aim is to reduce our reliance on fossil fuels. Electric vehicles with fuel-cells that use hydrogen as an energy carrier are touted to be one of the most important potential replacements of the gasoline vehicle in both future transportation scenarios and emerging smart energy grids. However hydrogen storage is a major technical barrier that lies between where we are now and the mass application of hydrogen energy. Further exploration of onboard hydrogen storage systems (OHSS) is urgently needed and in this regard a comprehensive technology opportunity analysis will help. Hence with this research we drew on scientific papers and patents related to OHSS and developed a novel methodology for investigating the past present and future development trends in OHSS. Specifically we constructed a heterogeneous knowledge network using a unique multi-component structure with three core components: hydrogen carriers hydrogen storage materials and fuel cells. From this network we extracted both the developed and underdeveloped technological solutions in the field and applied a well-designed evaluation system and prediction model to score the future development potential of these technological solutions. What emerged was the most promising directions of research in the short medium and long term. The results show that our methodology can effectively identify technology opportunities in OHSS along with providing valuable decision support to researchers and enterprise managers associated with the development and application of OHSS.
Toward Sustainability: An Overview of the Use of Green Hydrogen in the Agriculture and Livestock Sector
Aug 2023
Publication
The agro-livestock sector produces about one third of global greenhouse gas (GHG) emissions. Since more energy is needed to meet the growing demand for food and the industrial revolution in agriculture renewable energy sources could improve access to energy resources and energy security reduce dependence on fossil fuels and reduce GHG emissions. Hydrogen production is a promising energy technology but its deployment in the global energy system is lagging. Here we analyzed the theoretical and practical application of green hydrogen generated by electrolysis of water powered by renewable energy sources in the agro-livestock sector. Green hydrogen is at an early stage of development in most applications and barriers to its large-scale deployment remain. Appropriate policies and financial incentives could make it a profitable technology for the future.
Expert Perceptions of Game-changing Innovations towards Net Zero
Dec 2022
Publication
Current technological improvements are yet to put the world on track to net-zero which will require the uptake of transformative low-carbon innovations to supplement mitigation efforts. However the role of such innovations is not yet fully understood; some of these ‘miracles’ are considered indispensable to Paris Agreement-compliant mitigation but their limitations availability and potential remain a source of debate. We evaluate such potentially game-changing innovations from the experts’ perspective aiming to support the design of realistic decarbonisation scenarios and better-informed net-zero policy strategies. In a worldwide survey 260 climate and energy experts assessed transformative innovations against their mitigation potential at-scale availability and/or widescale adoption and risk of delayed diffusion. Hierarchical clustering and multi-criteria decision-making revealed differences in perceptions of core technological innovations with next generation energy storage alternative building materials iron-ore electrolysis and hydrogen in steelmaking emerging as top priorities. Instead technologies highly represented in well-below-2◦C scenarios seemingly feature considerable and impactful delays hinting at the need to re-evaluate their role in future pathways. Experts’ assessments appear to converge more on the potential role of other disruptive innovations including lifestyle shifts and alternative economic models indicating the importance of scenarios including non-technological and demand-side innovations. To provide insights for expert elicitation processes we finally note caveats related to the level of representativeness among the 260 engaged experts the level of their expertise that may have varied across the examined innovations and the potential for subjective interpretation to which the employed linguistic scales may be prone to.
Thermocatalytic Hydrogen Production Through Decomposition of Methane-A Review
Oct 2021
Publication
Consumption of fossil fuels especially in transport and energy-dependent sectors has led to large greenhouse gas production. Hydrogen is an exciting energy source that can serve our energy purposes and decrease toxic waste production. Decomposition of methane yields hydrogen devoid of COx components thereby aiding as an eco-friendly approach towards large-scale hydrogen production. This review article is focused on hydrogen production through thermocatalytic methane decomposition (TMD) for hydrogen production. The thermodynamics of this approach has been highlighted. Various methods of hydrogen production from fossil fuels and renewable resources were discussed. Methods including steam methane reforming partial oxidation of methane auto thermal reforming direct biomass gasification thermal water splitting methane pyrolysis aqueous reforming and coal gasification have been reported in this article. A detailed overview of the different types of catalysts available the reasons behind their deactivation and their possible regeneration methods were discussed. Finally we presented the challenges and future perspectives for hydrogen production via TMD. This review concluded that among all catalysts nickel ruthenium and platinum-based catalysts show the highest activity and catalytic efficiency and gave carbon-free hydrogen products during the TMD process. However their rapid deactivation at high temperatures still needs the attention of the scientific community.
Net Hydrogen Consumption Minimization of Fuel Cell Hybrid Trains Using a Time-Based Co-Optimization Model
Apr 2022
Publication
With increasing concerns on transportation decarbonization fuel cell hybrid trains (FCHTs) attract many attentions due to their zero carbon emissions during operation. Since fuel cells alone cannot recover the regenerative braking energy (RBE) energy storage devices (ESDs) are commonly deployed for the recovery of RBE and provide extra traction power to improve the energy efficiency. This paper aims to minimize the net hydrogen consumption (NHC) by co-optimizing both train speed trajectory and onboard energy management using a time-based mixed integer linear programming (MILP) model. In the case with the constraints of speed limits and gradients the NHC of co-optimization reduces by 6.4% compared to the result obtained by the sequential optimization which optimizes train control strategies first and then the energy management. Additionally the relationship between NHC and employed ESD capacity is studied and it is found that with the increase of ESD capacity the NHC can be reduced by up to 30% in a typical route in urban railway transit. The study shows that ESDs play an important role for FCHTs in reducing NHC and the proposed time-based co-optimization model can maximize the energy-saving benefits for such emerging traction systems with hybrid energy sources including both fuel cells and ESD.
Solar Hydrogen for High Capacity, Dispatchable, Long-distance Energy transmission – A Case Study for Injection in the Greenstream Natural Gas Pipeline
Nov 2022
Publication
This paper presents the results of techno-economic modelling for hydrogen production from a photovoltaic battery electrolyser system (PBES) for injection into a natural gas transmission line. Mellitah in Libya connected to Gela in Italy by the Greenstream subsea gas transmission line is selected as the location for a case study. The PBES includes photovoltaic (PV) arrays battery electrolyser hydrogen compressor and large-scale hydrogen storage to maintain constant hydrogen volume fraction in the pipeline. Two PBES configurations with different large-scale storage methods are evaluated: PBESC with compressed hydrogen stored in buried pipes and PBESL with liquefied hydrogen stored in spherical tanks. Simulated hourly PV electricity generation is used to calculate the specific hourly capacity factor of a hypothetical PV array in Mellitah. This capacity factor is then used with different PV sizes for sizing the PBES. The levelised cost of delivered hydrogen (LCOHD) is used as the key techno-economic parameter to optimise the size of the PBES by equipment sizing. The costs of all equipment except the PV array and batteries are made to be a function of electrolyser size. The equipment sizes are deemed optimal if PBES meets hydrogen demand at the minimum LCOHD. The techno-economic performance of the PBES is evaluated for four scenarios of fixed and constant hydrogen volume fraction targets in the pipeline: 5% 10% 15% and 20%. The PBES can produce up to 106 kilotonnes of hydrogen per year to meet the 20% target at an LCOHD of 3.69 €/kg for compressed hydrogen storage (PBESC) and 2.81 €/kg for liquid hydrogen storage (PBESL). Storing liquid hydrogen at large-scale is significantly cheaper than gaseous hydrogen even with the inclusion of a significantly larger PV array that is required to supply additional electrcitiy for liquefaction.
Hydrogen Production by Solar Thermochemical Water-Splitting Cycle via a Beam Down Concentrator
May 2021
Publication
About 95% of the hydrogen presently produced is from natural gas and coal and the remaining 5% is generated as a by-product from the production of chlorine through electrolysis1 . In the hydrogen economy (Crabtree et al. 2004; Penner 2006; Marbán and Valdés-Solís 2007) hydrogen is produced entirely from renewable energy. The easiest approach to advance renewable energy production is through solar photovoltaic and electrolysis a pathway of high technology readiness level (TRL) suffering however from two downfalls. First of all electricity is already an energy carrier and transformation with a penalty into another energy carrier hydrogen is in principle flawed. The second problem is that the efficiency of commercial solar panels is relatively low. The cadmium telluride (CdTe) thin-film solar cells have a solar energy conversion efficiency of 17%. Production of hydrogen using the current best processes for water electrolysis has an efficiency of ∼70%. As here explained the concentrated solar energy may be used to produce hydrogen using thermochemical water-splitting cycles at much global higher efficiency (fuel energy to incident sun energy). This research and development (R&D) effort is therefore undertaken to increase the TRL of this approach as a viable and economical option.
The Potential Role of a Hydrogen Network in Europe
Jul 2023
Publication
Europe’s electricity transmission expansion suffers many delays despite its significance for integrating renewable electricity. A hydrogen network reusing the existing gas network could not only help to supply the demand for low-emission fuels but could also balance variations in wind and solar energies across the continent and thus avoid power grid expansion. Our investigation varies the allowed expansion of electricity and hydrogen grids in net-zero CO2 scenarios for a sector-coupled European energy system capturing transmission bottlenecks renewable supply and demand variability and pipeline retrofitting and geological storage potentials. We find that a hydrogen network connecting regions with low-cost and abundant renewable potentials to demand centers electrofuel production and cavern storage sites reduces system costs by up to 26 bnV/a (3.4%). Although expanding both networks together can achieve the largest cost reductions by 9.9% the expansion of neither is essential for a net-zero system as long as higher costs can be accepted and flexibility options allow managing transmission bottlenecks.
A Green Route for Hydrogen Producton from Alkaline Thermal Treatment (ATT) of Biomass with Carbon Storage
Apr 2023
Publication
Hydrogen a green energy carrier is one of the most promising energy sources. However,it is currently mainly produced from depleting fossil fuels with high carbon emissions which has serious negative effects on the economy and environment. To address this issue sustainable hydrogen production from bio-energy with carbon capture and storage (HyBECCS) is an ideal technology to reduce global carbon emissions while meeting energy demand. This review presents an overview of the latest progress in alkaline thermal treatment (ATT) of biomass for hydrogen production with carbon storage especially focusing on the technical characteristics and related challenges from an industrial application perspective. Additionally the roles of alkali and catalyst in the ATT process are critically discussed and several aspects that have great influences on the ATT process such as biomass types reaction parameters and reactors are expounded. Finally the potential solutions to the general challenges and obstacles to the future industrial-scale application of ATT of biomass for hydrogen production are proposed.
CFD Thermo‑Hydraulic Evaluation of a Liquid Hydrogen Storage Tank with Different Insulation Thickness in a Small‑Scale Hydrogen Liquefier
Aug 2023
Publication
Accurate evaluation of thermo‑fluid dynamic characteristics in tanks is critically important for designing liquid hydrogen tanks for small‑scale hydrogen liquefiers to minimize heat leakage into the liquid and ullage. Due to the high costs most future liquid hydrogen storage tank designs will have to rely on predictive computational models for minimizing pressurization and heat leakage. Therefore in this study to improve the storage efficiency of a small‑scale hydrogen liquefier a three‑ dimensional CFD model that can predict the boil‑off rate and the thermo‑fluid characteristics due to heat penetration has been developed. The prediction performance and accuracy of the CFD model was validated based on comparisons between its results and previous experimental data and a good agreement was obtained. To evaluate the insulation performance of polyurethane foam with three different insulation thicknesses the pressure changes and thermo‑fluid characteristics in a partially liquid hydrogen tank subject to fixed ambient temperature and wind velocity were investigated nu‑ merically. It was confirmed that the numerical simulation results well describe not only the temporal variations in the thermal gradient due to coupling between the buoyance and convection but also the buoyancy‑driven turbulent flow characteristics inside liquid hydrogen storage tanks with differ‑ ent insulation thicknesses. In the future the numerical model developed in this study will be used for optimizing the insulation systems of storage tanks for small‑scale hydrogen liquefiers which is a cost‑effective and highly efficient approach.
Can the Hydrogen Economy Concept be the Solution to the Future Energy Crisis?
Feb 2022
Publication
The Hydrogen Economy concept is being proposed as a means of reducing and eventually decarbonising the world’s energy use. It looks to hydrogen as being a replacement for methane (natural gas) and generally as a way of removing all fossil fuels from the energy supply. The concept however has at least four flaws as follows: (1) hydrogen has significantly different properties to methane; (2) hydrogen has properties that create significant hazards; (3) hydrogen has a very small initiation (activation) energy; and (4) liquid hydrogen cannot readily replace liquefied natural gas (LNG). Hydrogen’s hazards will prevent it from being accepted in a societal sense. To the question ‘Can the Hydrogen Economy concept be the solution to the future energy crisis?’ the answer is ‘no’. Hydrogen has and will have a role in world energy but that role will be limited to industry. For the future we need an advanced electric economy.
An Insight into Underground Hydrogen Storage in Italy
Apr 2023
Publication
Hydrogen is a key energy carrier that could play a crucial role in the transition to a low-carbon economy. Hydrogen-related technologies are considered flexible solutions to support the large-scale implementation of intermittent energy supply from renewable sources by using renewable energy to generate green hydrogen during periods of low demand. Therefore a short-term increase in demand for hydrogen as an energy carrier and an increase in hydrogen production are expected to drive demand for large-scale storage facilities to ensure continuous availability. Owing to the large potential available storage space underground hydrogen storage offers a viable solution for the long-term storage of large amounts of energy. This study presents the results of a survey of potential underground hydrogen storage sites in Italy carried out within the H2020 EU Hystories “Hydrogen Storage In European Subsurface” project. The objective of this work was to clarify the feasibility of the implementation of large-scale storage of green hydrogen in depleted hydrocarbon fields and saline aquifers. By analysing publicly available data mainly well stratigraphy and logs we were able to identify onshore and offshore storage sites in Italy. The hydrogen storage capacity in depleted gas fields currently used for natural gas storage was estimated to be around 69.2 TWh.
Hydrogen Production by Water Electrolysis Technologies: A Review
Sep 2023
Publication
Hydrogen as an energy source has been identified as an optimal pathway for mitigating climate change by combining renewable electricity with water electrolysis systems. Proton exchange membrane (PEM) technology has received a substantial amount of attention because of its ability to efficiently produce high-purity hydrogen while minimising challenges associated with handling and maintenance. Another hydrogen generation technology alkaline water electrolysis (AWE) has been widely used in commercial hydrogen production applications. Anion exchange membrane (AEM) technology can produce hydrogen at relatively low costs because the noble metal catalysts used in PEM and AWE systems are replaced with conventional low-cost electrocatalysts. Solid oxide electrolyzer cell (SOEC) technology is another electrolysis technology for producing hydrogen at relatively high conversion efficiencies low cost and with low associated emissions. However the operating temperatures of SOECs are high which necessitates long startup times. This review addresses the current state of technologies capable of using impure water in water electrolysis systems. Commercially available water electrolysis systems were extensively discussed and compared. The technical barriers of hydrogen production by PEM and AEM were also investigated. Furthermore commercial PEM stack electrolyzer performance was evaluated using artificial river water (soft water). An integrated system approach was recommended for meeting the power and pure water demands using reversible seawater by combining renewable electricity water electrolysis and fuel cells. AEM performance was considered to be low requiring further developments to enhance the membrane’s lifetime.
Transition Analysis of Budgetary Allocation for Projects on Hydrogen-Related Technologies in Japan
Oct 2020
Publication
Hydrogen technologies are promising candidates of new energy technologies for electric power load smoothing. However regardless of long-term public investment hydrogen economy has not been realized. In Japan the National Research and Development Institute of New Energy and Industrial Technology Development Organization (NEDO) a public research-funding agency has invested more than 200 billion yen in the technical development of hydrogen-related technologies. However hydrogen technologies such as fuel cell vehicles (FCVs) have not been disseminated yet. Continuous and strategic research and development (R&D) are needed but there is a lack of expertise in this field. In this study the transition of the budgetary allocations by NEDO were analyzed by classifying NEDO projects along the hydrogen supply chain and research stage. We found a different R&D focus in different periods. From 2004 to 2007 empirical research on fuel cells increased with the majority of research focusing on standardization. From 2008 to 2011 investment in basic research of fuel cells increased again the research for verification of fuel cells continued and no allocation for research on hydrogen production was confirmed. Thereafter the investment trend did not change until around 2013 when practical application of household fuel cells (ENE-FARM) started selling in 2009 in terms of hydrogen supply chain. Hydrogen economy requires a different hydrogen supply infrastructure that is an existing infrastructure of city gas for ENE-FARM and a dedicated infrastructure for FCVs (e.g. hydrogen stations). We discussed the possibility that structural inertia could prevent the transition to investing more in hydrogen infrastructure from hydrogen utilization technology. This work has significant implications for designing national research projects to realize hydrogen economy.
Interdisciplinary Perspectives on Offshore Energy System Integration in the North Sea: A Systematic Literature Review
Oct 2023
Publication
To facilitate the rapid and large-scale developments of offshore wind energy scholars policymakers and infrastructure developers must start considering its integration into the larger onshore energy system. Such offshore system integration is defined as the coordinated approach to planning and operation of energy generation transport and storage in the offshore energy system across multiple energy carriers and sectors. This article conducts a systematic literature review to identify infrastructure components of offshore energy system integration (including alternative cable connections offshore energy storage and power-to-hydrogen applications) and barriers to their development. An interdisciplinary perspective is provided where current offshore developments require not only mature and economically feasible technologies but equally strong legal and governance frameworks. The findings demonstrate that current literature lacks a holistic perspective on the offshore energy system. To date techno-economic assessments solving challenges of specific infrastructure components prevail over an integrated approach. Nevertheless permitting issues gaps in legal frameworks strict safety and environmental regulations and spatial competition also emerge as important barriers. Overall this literature review emphasizes the necessity of aligning various disciplines to provide a fundamental approach for the development of an integrated offshore energy system. More specifically timely policy and legal developments are key to incentivize technical development and enable economic feasibility of novel components of offshore system integration. Accordingly to maximize real-world application and policy learning future research will benefit from an interdisciplinary perspective.
Comparative Exergy and Environmental Assessment of the Residual Biomass Gasification Routes for Hydrogen and Ammonia Production
Jul 2023
Publication
The need to reduce the dependency of chemicals on fossil fuels has recently motivated the adoption of renewable energies in those sectors. In addition due to a growing population the treatment and disposition of residual biomass from agricultural processes such as sugar cane and orange bagasse or even from human waste such as sewage sludge will be a challenge for the next generation. These residual biomasses can be an attractive alternative for the production of environmentally friendly fuels and make the economy more circular and efficient. However these raw materials have been hitherto widely used as fuel for boilers or disposed of in sanitary landfills losing their capacity to generate other by-products in addition to contributing to the emissions of gases that promote global warming. For this reason this work analyzes and optimizes the biomass-based routes of biochemical production (namely hydrogen and ammonia) using the gasification of residual biomasses. Moreover the capture of biogenic CO2 aims to reduce the environmental burden leading to negative emissions in the overall energy system. In this context the chemical plants were designed modeled and simulated using Aspen plus™ software. The energy integration and optimization were performed using the OSMOSE Lua Platform. The exergy destruction exergy efficiency and general balance of the CO2 emissions were evaluated. As a result the irreversibility generated by the gasification unit has a relevant influence on the exergy efficiency of the entire plant. On the other hand an overall negative emission balance of −5.95 kgCO2/kgH2 in the hydrogen production route and −1.615 kgCO2/kgNH3 in the ammonia production route can be achieved thus removing from the atmosphere 0.901 tCO2/tbiomass and 1.096 tCO2/tbiomass respectively.
Selected Materials and Technologies for Electrical Energy Sector
Jun 2023
Publication
Ensuring the energy transition in order to decrease CO2 and volatile organic compounds emissions and improve the efficiency of energy processes requires the development of advanced materials and technologies for the electrical energy sector. The article reviews superconducting materials functional nanomaterials used in the power industry mainly due to their magnetic electrical optical and dielectric properties and the thin layers of amorphous carbon nitride which properties make them an important material from the point of view of environmental protection optoelectronic photovoltaic and energy storage. The superconductivity-based technologies material processing and thermal and nonthermal plasma generation have been reviewed as technologies that can be a solution to chosen problems in the electrical energy sector and environment. The study explains directly both—the basics and application potential of low and high-temperature superconductors as well as peculiarities of the related manufacturing technologies for Roebel cables 1G and 2G HTS tapes and superconductor coil systems. Among the superconducting materials particular attention was paid to the magnesium di-boride MgB2 and its potential applications in the power industry. The benefits of the use of carbon films with amorphous structures in electronics sensing technologies solar cells FETs and memory devices were discussed. The article provides the information about most interesting from the R&D point of view groups of materials for PV applications. It summarises the advantages and disadvantages of their use regarding commercial requirements such as efficiency lifetime light absorption impact on the environment costs of production and weather dependency. Silicon processing inkjet printing vacuum deposition and evaporation technologies that allow obtaining improved and strengthened materials for solar cell manufacturing are also described. In the case of the widely developed plasma generation field waste-to-hydrogen technology including both thermal and non-thermal plasma techniques has been discussed. The review aims to draw attention to the problems faced by the modern power industry and to encourage research in this area because many of these problems can only be solved within the framework of interdisciplinary and international cooperation.
Chemical Kinetic Analysis of High-Pressure Hydrogen Ignition and Combustion toward Green Aviation
Jan 2024
Publication
In the framework of the “Multidisciplinary Optimization and Regulations for Low-boom and Environmentally Sustainable Supersonic aviation” project pursued by a consortium of European government and academic institutions coordinated by Politecnico di Torino under the European Commission Horizon 2020 financial support the Italian Aerospace Research Centre is computationally investigating the high-pressure hydrogen/air kinetic combustion in the operative conditions typically encountered in supersonic aeronautic ramjet engines. This task is being carried out starting from the zero-dimensional and one-dimensional chemical kinetic assessment of the complex and strongly pressure-sensitive ignition behavior and flame propagation characteristics of hydrogen combustion through the validation against experimental shock tube and laminar flame speed measurements. The 0D results indicate that the kinetic mechanism by Politecnico di Milano and the scheme formulated by Kéromnès et al. provide the best matching with the experimental ignition delay time measurements carried out in high-pressure shock tube strongly argon-diluted reaction conditions. Otherwise the best behavior in terms of laminar flame propagation is achieved by the Mueller scheme while the other investigated kinetic mechanisms fail to predict the flame speeds at elevated pressures. This confirms the non-linear and intensive pressure-sensitive behavior of hydrogen combustion especially in the critical high-pressure and low-temperature region which is hard to be described by a single all-encompassing chemical model.
Blue Hydrogen Production from Natural Gas Reservoirs: A Review of Application and Feasibility
Feb 2023
Publication
Recently interest in developing H2 strategies with carbon capture and storage (CCS) technologies has surged. Considering that this paper reviews recent literature on blue H2 a potential low-carbon short-term solution during the H2 transition period. Three key aspects were the focus of this paper. First it presents the processes used for blue H2 production. Second it presents a detailed comparison between blue H2 and natural gas as fuels and energy carriers. The third aspect focuses on CO2 sequestration in depleted natural gas reservoirs an essential step for implementing blue H2. Globally ~ 75% of H2 is produced using steam methane reforming which requires CCS to obtain blue H2. Currently blue H2 needs to compete with other advancing technologies such as green H2 solar power battery storage etc. Compared to natural gas and liquefied natural gas blue H2 gas results in lower CO2 emissions since CCS is applied. However transporting liquefied and compressed blue H2 entails higher energy economic and environmental costs. CCS must be appropriately implemented to produce blue H2 successfully. Due to their established capacity to trap hydrocarbons over geologic time scales depleted natural gas reservoirs are regarded as a viable option for CCS. Such a conclusion is supported by several simulation studies and field projects in many countries. Additionally there is much field experience and knowledge on the injection and production performance of natural gas reservoirs. Therefore using the existing site infrastructure converting these formations into storage reservoirs is undemanding.
Routes for Hydrogen Introduction in the Industrial Hard-to-Abate Sectors for Promoting Energy Transition
Aug 2023
Publication
This paper offers a set of comprehensive guidelines aimed at facilitating the widespread adoption of hydrogen in the industrial hard-to-abate sectors. The authors begin by conducting a detailed analysis of these sectors providing an overview of their unique characteristics and challenges. This paper delves into specific elements related to hydrogen technologies shedding light on their potential applications and discussing feasible implementation strategies. By exploring the strengths and limitations of each technology this paper offers valuable insights into its suitability for specific applications. Finally through a specific analysis focused on the steel sector the authors provide in-depth information on the potential benefits and challenges associated with hydrogen adoption in this context. By emphasizing the steel sector as a focal point the authors contribute to a more nuanced understanding of hydrogen’s role in decarbonizing industrial processes and inspire further exploration of its applications in other challenging sectors.
Decarbonisation Options for the Cement Industry
Jan 2023
Publication
The cement industry is a building block of modern society and currently responsible for around 7% of global and 4% of EU CO2 emissions. While facing global competition and a challenging business environment the EU cement sector needs to decarbonise its production processes to comply with the EU’s ambitious 2030 and 2050 climate targets. This report provides a snapshot of the current cement production landscape and discusses future technologies that are being explored by the sector to decarbonise its processes describing the transformational change the industry faces. This report compiles the current projects and announcements to deploy breakthrough technologies which do require high capital investments. However with 2050 just one investment cycle away the sector needs to commercialise new low-CO2 technologies this decade to avoid the risk of stranded assets. As Portland cement production is highly CO2-intensive and EU plants are already operating close to optimum efficiency the industry appears to be focussing on carbon capture storage and utilisation technologies - while breakthroughs in alternative chemistries are still being explored - to reduce emissions. While the EU has played an important role in supporting early stage R&D for these technologies it is now striving to fill the funding gap for the commercialisation of breakthrough technologies. The recent momentum towards CO2-free cement provides the EU with the opportunity to be a frontrunner in creating markets for green cement.
A Review on Experimental Studies Investigating the Effect of Hydrogen Supplementation in CI Diesel Engines—The Case of HYMAR
Aug 2022
Publication
Hydrogen supplementation in diesel Compression Ignition (CI) engines is gaining more attention since it is considered as a feasible solution to tackle the challenges that are related to the emission regulations that will be applied in the forthcoming years. Such a solution is very attractive because it requires only limited modifications to the existing technology of internal combustion CI engines. To this end numerous work on the investigation of an engine’s performance and the effects of emissions when hydrogen is supplied in the engine’s cylinders has been completed by researchers. However contradictory results were found among these studies regarding the efficiency of the engine and the emission characteristics achieved compared to the diesel-only operation. The different conclusions might be attributed to the different characteristics and technology level of the engines that were utilized as well as on the chosen operational parameters. This paper aims to present an overview of the experimental studies that have examined the effects of hydrogen addition in CI four-stroke diesel engines reporting the characteristics of the utilized engines the quantities of hydrogen tested the method of hydrogen induction used as well as the operational conditions tested in order to help interested researchers to easily identify relevant and appropriate studies to perform comparisons or validations by repeating certain cases. The presented data do not include any results or conclusions from these studies. Furthermore an experimental configuration along with the appropriate modifications on a heavy-duty auxiliary generator-set engine that was recently developed by the authors for the purposes of the HYMAR project is presented.
Power Scheduling Optimization Method of Wind-Hydrogen Integrated Energy System Based on the Improved AUKF Algorithm test2
Nov 2022
Publication
With the proposal of China’s green energy strategy the research and development technologies of green energy such as wind energy and hydrogen energy are becoming more and more mature. However the phenomenon of wind abandonment and anti-peak shaving characteristics of wind turbines have a great impact on the utilization of wind energy. Therefore this study firstly builds a distributed wind-hydrogen hybrid energy system model then proposes the power dispatching optimization technology of a wind-hydrogen integrated energy system. On this basis a power allocation method based on the AUKF (adaptive unscented Kalman filter) algorithm is proposed. The experiment shows that the power allocation strategy based on the AUKF algorithm can effectively reduce the incidence of battery overcharge and overdischarge. Moreover it can effectively deal with rapid changes in wind speed. The wind hydrogen integrated energy system proposed in this study is one of the important topics of renewable clean energy technology innovation. Its grid-connected power is stable with good controllability and the DC bus is more secure and stable. Compared with previous studies the system developed in this study has effectively reduced the ratio of abandoned air and its performance is significantly better than the system with separate grid connected fans and single hydrogen energy storage. It is hoped that this research can provide some solutions for the research work on power dispatching optimization of energy systems.
Determining the Production and Transport Cost for H2 on a Global Scale
May 2022
Publication
Hydrogen (H2) produced using renewable energy could be used to reduce greenhouse gas (GHG) emissions in industrial sectors such as steel chemicals transportation and energy storage. Knowing the delivered cost of renewable H2 is essential to decisionmakers looking to utilize it. The cheapest location to source it from as well as the transport method and medium are also crucial information. This study presents a Monte Carlo simulation to determine the delivered cost for renewable H2 for any usage location globally as well as the most cost-effective production location and transport route from nearly 6000 global locations. Several industrially dense locations are selected for case studies the primary two being Cologne Germany and Houston United States. The minimum delivered H2 cost to Cologne is 9.4 €/kg for small scale (no pipelines considered) shipped from northern Egypt as a liquid organic hydrogen carrier (LOHC) and 7.6 €/kg piped directly as H2 gas from southern France for large scale (pipelines considered). For smallscale H2 in Houston the minimum delivered cost is 8.6 €/kg trucked as H2 gas from the western Gulf of Mexico and 7.6 €/kg for large-scale demand piped as H2 gas from southern California. The south-west United States and Mexico northern Chile the Middle East and north Africa south-west Africa and north-west Australia are identified as the regions with the lowest renewable H2 cost potential with production costs ranging from 6.7—7.8 €/kg in these regions. Each is able to supply differing industrially dominant areas. Furthermore the effect of parameters such as year of construction electrolyser and H2 demand is analysed. For the case studies in Houston and Cologne the delivered H2 cost is expected to reduce to about 7.8 €/kg by 2050 in Cologne (no pipelines considered PEM electrolyser) and 6.8 €/kg in Houston.
Life Cycle Analysis of Hydrogen Powered Marine Vessels—Case Ship Comparison Study with Conventional Power System
Aug 2023
Publication
The latest International Maritime Organization strategies aim to reduce 70% of the CO2 emissions and 50% of the Greenhouse Gas (GHG) emissions from maritime activities by 2050 compared to 2008 levels. The EU has set up goals to reduce GHG emissions by at least 55% by 2030 compared to 1990 and achieve net-zero GHG emissions by 2050. The UK aims to achieve more than 68% GHG emission reduction by 2030 and net-zero GHG emissions by 2050. There are many solutions under development to tackle the challenge of meeting the latest decarbonization strategies from the IMO EU and UK among which are hydrogen powered marine vessels. This paper presents a life cycle analysis study for hydrogen fuelled vessels by evaluating their performance in terms of environmental friendliness and economic feasibility. The LCA study will consider the gas emissions and costs during the life stages of the ships including the construction operation maintenance and recycling phases of the selected vessels. The results of the comparisons with the conventional version of the ships (driven by diesel generators) demonstrate the benefits of using hydrogen for marine transportation: over 80% emission reduction and around 60% life cycle cost savings. A sensitivity analysis shows that the prices of fuels and carbon credits can affect the life cycle cost and recommendations for low H2 price and high carbon credit in the future are provided to attract the industry to adopt the new fuel.
Hydrogen Fuel Cell Integration and Testing in a Hybrid-electric Propulsion Rig
Jun 2023
Publication
On the road towards greener aviation hybrid-electric propulsion systems have emerged as a viable solution. In this paper a system based on hydrogen fuel cells is proposed and evaluated in a laboratory setting with its future integration in a propulsive system in mind and main focus on the ability to lessen the power demand on the opposing side of the bench. The setup consists in a parallel architecture with two power sources: a hydrogen fuel cell and a battery. First the performance of the fuel cell and its capability to provide power to one of the motors are analyzed. Then the entire parallel hybrid system is evaluated. Although the experimental setup was shown to be sub-optimal the results demonstrated the ability of this greener alternative to reduce power demand on the opposing side of the parallel configuration with a reduction of up to 40.3% in the highest load scenario and maximum power output on the fuel cell of 257.8 W. The stack performance was also concluded to be very dependent on the operating temperature.
The Impact of Sustainable Energy Technologies and Demand Response Programs on the Hub's Planning by the Practical Consideration of Tidal Turbines as a Novel Option
Apr 2023
Publication
This paper investigates a multi-objective optimal energy planning strategy for a hub incorporating renewable and non-renewable resources like PV tidal turbine fuel-cell CHP boiler micro-turbine reactor reformer electrolyzer and energy storage by utilizing the time of use program (TOU). In this strategy tidal turbine fuel-cell and reformer technologies are considered novel technologies that simultaneously reduce the proposed hub’s cost and pollution. The hub’s total cost and pollution are considered objective functions. To make the results more realistic characteristics of the tidal turbine are investigated by utilizing the manufactory’s company information. The problem is then modeled as real mixed integer programming (RMIP) and is solved in GAMS software using a CPLEX solver. Epsilon constraints method and fuzzy satisfying approach are used to select the optimal solution based on the proposed model. Finally a sensitivity analysis is performed to assess the effective parameters that affect the planning’s results. The results show that the overall pollution is reduced by about 9% by assuming the proposed planning and the total profit is increased by about 30%.
Biological Hydrogen Methanation with Carbon Dioxide Utilization: Methanation Acting as Mediator in the Hydrogen Economy
May 2023
Publication
Hydrogen is one of the main energy carriers playing a prominent role in the future decarbonization of the economy. However several aspects regarding the transport and storage of this gas are challenging. The intermediary conversion of hydrogen into high-density energy molecules may be a crucial step until technological conditions are ready to attain a significant reduction in fossil fuel use in transport and the industrial sector. The process of transforming hydrogen into methane by anaerobic digestion is reviewed showing that this technology is a feasible option for facilitating hydrogen storage and transport. The manuscript focuses on the role of anaerobic digestion as a technology driver capable of fast adaptation to current energy needs. The use of thermophilic systems and reactors capable of increasing the contact between the H2 -fuel and liquid phase demonstrated outstanding capabilities attaining higher conversion rates and increasing methane productivity. Pressure is a relevant factor of the process allowing for better hydrogen solubility and setting the basis for considering feasible underground hydrogen storage concomitant with biological methanation. This feature may allow the integration of sequestered carbon dioxide as a relevant substrate.
Microfluidic Storage Capacity and Residual Trapping During Cyclic Injections: Implications for Underground Storage
Apr 2023
Publication
Long-term and large-scale H2 storage is vital for a sustainable H2 economy. Research in underground H2 storage (UHS) in porous media is emerging but the understanding of H2 reconnection and recovery mechanisms under cyclic loading is not yet adequate. This paper reports a qualitative and quantitative investigation of H2 reconnection and recovery mechanisms in repeated injection-withdrawal cycles. Here we use microfluidics to experimentally investigate up to 5 cycles of H2 injection and withdrawal under a range of injection rates at shallow reservoir storage conditions. We find that H2 storage capacities increase with increasing injection rate and range between ~10% and 60%. The residual H2 saturation is in the same range between cycles (30e40%) but its distribution in the pore space visually appears to be hysteretic. In most cases the residually trapped H2 reconnects in the subsequent injection cycle predominantly in proximity to the large pore clusters. Our results provide valuable experimental data to advance the understanding of multiple H2 injection cycles in UHS schemes.
Rethinking "BELVE Explosion" After Liquid Hydrogen Storage Tank Rupture in a Fire
Sep 2022
Publication
The underlying physical mechanisms leading to the generation of blast waves after liquid hydrogen (LH2) storage tank rupture in a fire are not yet fully understood. This makes it difficult to develop predictive models and validate them against a very limited number of experiments. This study aims at the development of a CFD model able to predict maximum pressure in the blast wave after the LH2 storage tank rupture in a fire. The performed critical review of previous works and the thorough numerical analysis of BMW experiments (LH2 storage pressure in the range 2.0e11.3 bar abs) allowed us to conclude that the maximum pressure in the blast wave is generated by gaseous phase starting shock enhanced by combustion reaction of hydrogen at the contact surface with heated by the shock air. The boiling liquid expanding vapour explosion (BLEVE) pressure peak follows the gaseous phase blast and is smaller in amplitude. The CFD model validated recently against high-pressure hydrogen storage tank rupture in fire experiments is essentially updated in this study to account for cryogenic conditions of LH2 storage. The simulation results provided insight into the blast wave and combustion dynamics demonstrating that combustion at the contact surface contributes significantly to the generated blast wave increasing the overpressure at 3 m from the tank up to 5 times. The developed CFD model can be used as a contemporary tool for hydrogen safety engineering e.g. for assessment of hazard distances from LH2 storage.
Thermodynamic Evaluation and Carbon Footprint Analysis of the Application of Hydrogen-Based Energy-Storage Systems in Residential Buildings
Sep 2016
Publication
This study represents a thermodynamic evaluation and carbon footprint analysis of the application of hydrogen based energy storage systems in residential buildings. In the system model buildings are equipped with photovoltaic (PV) modules and a hydrogen storage system to conserve excess PV electricity from times with high solar irradiation to times with low solar irradiation. Short-term storages enable a degree of self-sufficiency of approximately 60% for a single-family house (SFH) [multifamily house (MFH): 38%]. Emissions can be reduced by 40% (SFH) (MFH: 30%) compared to households without PV modules. These results are almost independent of the applied storage technology. For seasonal storage the degree of self-sufficiency ranges between 57 and 83% (SFH). The emission reductions highly depend on the storage technology as emissions caused by manufacturing the storage dominate the emission balance. Compressed gas or liquid organic hydrogen carriers are the best options enabling emission reductions of 40%.
Simulation and Control Strategy Study of the Hydrogen Supply System of a Fuel Cell Engine
Jun 2023
Publication
The hydrogen supply system is one of the important components of a hydrogen fuel cell engine and its performance has an important impact on the economy and power of the engine system. In this paper a hydrogen supply system based on cyclic mode is designed for a hydrogen fuel cell stack with a full load power of 150 kW and the corresponding hydrogen fuel cell engine simulation model is built and validated. The control strategy of the fuel cell hydrogen supply system is developed and its effect is verified through bench tests. The results show that the developed control strategy can keep the volume fraction of nitrogen below 6% the hydrogen excess ratio does not exceed 1.5 under medium and high operating conditions the anode pressure is relatively stable and the stack can operate efficiently and reliably.
The Role of Liquid Hydrogen in Integrated Energy Systems - A Case Study for Germany
May 2023
Publication
Hydrogen (H2) is expected to be a key building block in future greenhouse gas neutral energy systems. This study investigates the role of liquid hydrogen (LH2) in a national greenhouse gas-neutral energy supply system for Germany in 2045. The integrated energy system model suite ETHOS is extended by LH2 demand profiles in the sectors aviation mobility and chemical industry and means of LH2 transportation via inland vessel rail and truck. This case study demonstrates that the type of hydrogen demand (liquid or gaseous) can strongly affect the cost-optimal design of the future energy system. When LH2 demand is introduced to the energy system LH2 import transportation and production grow in importance. This decreases the need for gaseous hydrogen (GH2) pipelines and affects the location of H2 production plants. When identifying no-regret measures it must be considered that the largest H2 consumers are the ones with the highest readiness to use LH2.
Energy Performance Assessment of a Solar-driven Thermochemical Cycle Device for Green Hydrogen Production
Sep 2023
Publication
This paper presents a novel dynamic simulation model for assessing the energy performance of solar-driven systems employed in green hydrogen production. The system consists of a parabolic dish collector that focuses solar radiation on two cerium-based thermochemical reactors. The model is based on a transient finitedifference method to simulate the thermal behaviour of the system and it integrates a theoretical analysis of materials and operating principles. Different empirical data were considered for experimentally validating it: a good agreement between experimental and simulated results was obtained for the temperatures calculated inside the thermochemical reactor (R2 = 0.99 MAPE = 6.3%) and the hourly flow rates of hydrogen oxygen and carbon monoxide (R2 = 0.96 MAPE = 10%) inside the thermochemical reactor. The model was implemented in a MatLab tool for the system dynamic analysis under different boundary conditions. Subsequently to explore the capability of this approach the developed tool was used for analysing the examined device operating in twelve different weather zones. The obtained results comprise heat maps of specific crucial instants and hourly dynamic trends showing redox reaction cycles occurring into the thermochemical reactors. The yearly hydrogen production ranges from 1.19 m3 /y to 1.64 m3 /y according to the hourly incident solar radiations outdoor air temperatures and wind speeds. New graphic tools for rapid feasibility studies are presented. The developed tools and the obtained results can be useful to the basic design of this technology and for the multi-objective optimization of its layout and main design/operating parameters.
Contribution to Net Zero Emissions of Integrating Hydrogen Production in Wastewater Treatment Plants
Jul 2023
Publication
The reliability of renewable hydrogen supply for off-take applications is critical to the future sustainable energy economy. Integrated water electrolysis can be deployed at distributed municipal wastewater treatment plants (WWTP) creating opportunity for reduction in carbon emissions through direct and indirect use of the electrolysis output. A novel energy shifting process where the co-produced oxygen is compressed and stored to enhance the utilisation of intermittent renewable electricity is analysed. The hydrogen produced can be used in local fuel cell electric buses to replace incumbent diesel buses for public transport. However quantifying the extent of carbon emission reduction of this conceptual integrated system is key. In this study the integration of hydrogen production at a case study WWTP of 26000 EP capacity and using the hydrogen in buses was compared with two conventional systems: the base case of a WWTP with grid electricity consumption offset by solar PV and the community’s independent use of diesel buses for transport and the non-integrated configuration with hydrogen produced at the bus refuelling location operated independently of the WWTP. The system response was analysed using a Microsoft Excel simulation model with hourly time steps over a 12-month time frame. The model included a control scheme for the reliable supply of hydrogen for public transport and oxygen to the WWTP and considered expected reductions in carbon intensity of the national grid level of solar PV curtailment electrolyser efficiency and size of the solar PV system. Results showed that by 2031 when Australia’s national electricity is forecast to achieve a carbon intensity of less than 0.186 kg CO2-e/kWh integrating water electrolysis at a municipal WWTP for producing hydrogen for use in local hydrogen buses produced less carbon emissions than continuing to use diesel buses and offsetting emissions by exporting renewable electricity to the grid. By 2034 an annual reduction of 390 t–CO2–e is expected after changing to the integrated configuration. Considering electrolyser efficiency improvements and curtailment of renewable electricity the reduction increases to 872.8 t–CO2–e.
Greenhouse Gas Reduction Potential and Cost-effectiveness of Economy-wide Hydrogen-natural Gas Blending for Energy End Uses
Sep 2022
Publication
North American and European jurisdictions are considering repurposing natural gas infrastructure to deliver a lower carbon blend of natural gas and hydrogen; this paper evaluates the greenhouse gas reduction potential and cost-effectiveness of the repurposing. The analysis uses a bottom-up economy-wide energy-systems model of an emission-intensive jurisdiction Alberta Canada to evaluate 576 long-term scenarios from 2026 to 2050. Many scenarios were included to give the analysis broad international applicability and differ by sector hydrogen blending intensity carbon policy and hydrogen infrastructure development. Twelve hydrogen production technologies are compared in a long-term greenhouse gas and cost analysis including advanced technologies. Autothermal reforming with carbon capture provides both lower-carbon and lower-cost hydrogen compared to most other technologies in most futures even with high fugitive natural gas production emissions. Using hydrogen-natural gas blends for end-use energy applications eliminates 1–2% of economy-wide GHG emissions and marginal GHG abatement costs become negative at carbon prices over $300/tonne. The findings are useful for stakeholders expanding the international low-carbon hydrogen economy and governments engaged in formulating decarbonization policies and are considering hydrogen as an option.
Evaluation of Surplus Hydroelectricity Potential in Nepal until 2040 and its Use for Hydrogen Production Via Electrolysis
May 2023
Publication
The abundant hydro resources in Nepal have resulted in the generation of electricity almost exclusively from hydropower plants. Several hydropower plants are also currently under construction. There is no doubt that the surplus electricity will be significantly high in the coming years. Given the previous trend in electricity consumption it will be a challenge to maximize the use of surplus electricity. In this work the potential solutions to maximize the use of this surplus electricity have been analysed. Three approached are proposed: (i) increasing domestic electricity consumption by shifting the other energy use sectors to electricity (ii) cross-border export of electricity and (iii) conversion of electricity to hydrogen via electrolysis. The current state of energy demand and supply patterns in the country are presented. Future monthly demand forecasts and surplus electricity projections have been made. The hydrogen that can be produced with the surplus electricity via electrolysis is determined and an economic assessment is carried out for the produced hydrogen. The analysis of levelized cost of hydrogen (LCOH) under different scenarios resulted values ranging from 3.8 €/kg to 4.5 €/kg.
Multi-Objective Robust Optimization of Integrated Energy System with Hydrogen Energy Storage
Feb 2024
Publication
A novel multi-objective robust optimization model of an integrated energy system with hydrogen storage (HIES) considering source–load uncertainty is proposed to promote the low-carbon economy operation of the integrated energy system of a park. Firstly the lowest total system cost and carbon emissions are selected as the multi-objective optimization functions. The Pareto front solution set of the objective function is applied by compromise planning and the optimal solution among them is obtained by the maximum–minimum fuzzy method. Furthermore the robust optimization (RO) approach is introduced to cope with the source–load uncertainty effectively. Finally it is demonstrated that the illustrated HIES can significantly reduce the total system cost carbon emissions and abandoned wind and solar power. Meanwhile the effectiveness of the proposed model and solution method is verified by analyzing the influence of multi-objective solutions and a robust coefficient on the Chongli Demonstration Project in Hebei Province.
A Techno-economic Study of the Strategy for Hydrogen Transport by Pipelines in Canada
Jan 2023
Publication
Hydrogen as a clean zero-emission energy fuel will play a critical role in energy transition and achievement of the net-zero target in 2050. Hydrogen delivery is integral to the entire value chain of a full-scale hydrogen economy. This work conducted a systematic review and analysis of various hydrogen transportation methods including truck tankers for liquid hydrogen tube trailers for gaseous hydrogen and pipelines by identifying and ranking the main properties and affecting factors associated with each method. It is found that pipelines especially the existing natural gas pipelines provide a more efficient and cheaper means to transport hydrogen over long distances. Analysis was further conducted on Canadian natural gas pipeline network which has been operating for safe effective and efficient energy transport over six decades. The established infrastructure along with the developed operating and management experiences and skillful manpower makes the existing pipelines the best option for transport of hydrogen in either blended or pure form in the country. The technical challenges in repurposing the existing natural gas pipelines for hydrogen service were discussed and further work was analyzed.
A Comprehensive Resilience Assessment Framework for Hydrogen Energy Infrastructure Development
Jun 2023
Publication
In recent years sustainable development has become a challenge for many societies due to natural or other disruptive events which have disrupted economic environmental and energy infrastructure growth. Developing hydrogen energy infrastructure is crucial for sustainable development because of its numerous benefits over conventional energy sources. However the complexity of hydrogen energy infrastructure including production utilization and storage stages requires accounting for potential vulnerabilities. Therefore resilience needs to be considered along with sustainable development. This paper proposes a decision-making framework to evaluate the resilience of hydrogen energy infrastructure by integrating resilience indicators and sustainability contributing factors. A holistic taxonomy of resilience performance is first developed followed by a qualitative resilience assessment framework using a novel Intuitionistic fuzzy Weighted Influence Nonlinear Gauge System (IFWINGS). The results highlighted that Regulation and legislation Government preparation and Crisis response budget are the most critical resilience indicators in the understudy hydrogen energy infrastructure. A comparative case study demonstrates the practicality capability and effectiveness of the proposed approach. The results suggest that the proposed model can be used for resilience assessment in other areas.
No more items...