- Home
- A-Z Publications
- Publications
Publications
Compliance Measurements of Fuel Cell Electric Vehicle Exhaust
Sep 2019
Publication
The NREL Sensor Laboratory has been developing an analyzer that can verify compliance to the international United Nations Global Technical Regulation number 13 (GTR 13--Global Technical Regulation on Hydrogen and Fuel Cell Vehicles) prescriptive requirements pertaining to allowable hydrogen levels in the exhaust of fuel cell electric vehicles (FCEV) [1]. GTR 13 prescribes that the FCEV exhaust shall remain below 4 vol% H2 over a 3-second moving average and shall not at any time exceed 8 vol% H2 as verified with an analyzer with a response time (t90) of 300 ms or faster. GTR 13 has been implemented and is to serve as the basis for national regulations pertaining to hydrogen powered vehicle safety in the United States Canada Japan and the European Union. In the U.S. vehicle safety is overseen by the Department of Transportation (DOT) through the Federal Motor Vehicle Safety Standards (FMVSS) and in Canada by Transport Canada through the Canadian Motor Vehicle Safety Standard (CMVSS). The NREL FCEV exhaust analyzer is based upon a low-cost commercial hydrogen sensor with a response time (t90) of less than 250 ms. A prototype analyzer and gas probe assembly have been constructed and tested that can interface to the gas sampling system used by Environment and Climate Change Canada’s (ECCC) Emission Research and Measurement Section (ERMS) for the exhaust gas analysis. Through a partnership with Transport Canada ECCC will analyze the hydrogen level in the exhaust of a commercial FCEV. ECCC will use the NREL FCEV Exhaust Gas analyzer to perform these measurements. The analyzer was demonstrated on a FCEV operating under simulated road conditions using a chassis dynamometer at a private facility.
The Energy Approach to the Evaluation of Hydrogen Effect on the Damage Accumulation
Aug 2019
Publication
The energy approach for determining the durability of structural elements at high temperature creep and hydrogen activity was proposed. It has been shown that the approach significantly simplifies research compared with the known ones. Approbation of the approach was carried out on the example of determining the indicators of durability of the Bridgman sample under conditions of creep and different levels of hydrogenation of the metal. It was shown that with an increase of hydrogen concentration in the metal from 2 to 10 ppm the durability of the test sample decreased from 22 to 58%.
Notch-induced Anisotropic Fracture of Cold Drawn Pearlitic Steels and the Associated Crack Path Deflection and Mixed-mode Stress State: A Tribute to Masaccio
Jul 2018
Publication
This paper deals with notch-induced anisotropic fracture behavior of progressively cold drawn pearlitic steels on the basis of their microstructural evolution during manufacturing by multi-step cold drawing that produces slenderizing and orientation of the pearlitic colonies together with densification and orientation of the Fe/Fe3C lamellae reviewing previous research by the author. Results of fracture test using notched specimens of cold drawn pearlitic steels with different degrees of cold drawing (distinct levels of strain hardening) in air and hydrogen environment shows: (i) the key impact of the colonies and lamellae alignment and orientation on notch-induced fracture producing anisotropic fracture behavior with its related crack path deflection (or fracture path deviation); (ii) the necessity of both stress triaxiality (constraint) and microstructural orientation (colonies/lamellae) alignment to produce fracture path deflection; (iii) hydrogen presence (the circumstance) promotes crack path deviation in addition to the inherent microstructural anisotropy created by cold drawing; (iv) the anisotropic fracture path with a stepped profile in cold drawn pearlitic steel consisting of deflections and deviations from the initial transverse fracture path in mode I resembles Masaccio’s Tribute Money painting with its mountains at the background so that the present paper can be considered as a Tribute to Masaccio.
Site Selection Methodology for the Wind-powered Hydrogen Refueling Station Based on AHP-GIS in Adrar, Algeria
May 2019
Publication
This paper deals with site selection problems for hydrogen production plants and aims to propose a structural procedure for determining the most feasible sites. The study area is Adrar province Algeria which has a promising wind potential. The methodology is mainly composed of two stages: the first stage is to evaluate and select the best locations for wind-powered hydrogen production using GIS and MCDM technique. the AHP is applied to weigh the criteria and compute a LSI to evaluate potential sites and the second stage is applying different filtration constraints to select the suitable petrol stations for such hydrogen refuelling station modification. The result map showed that the entire Adrar province is almost suitable for wind-powered hydrogen production with varying suitability index. The LSI model groups sites into three categories: High suitable areas Medium suitable areas and Low suitable. As a result 2.95 % (12808.97 km2) of the study area has high suitability 54.59 % (236320.16 km2) has medium suitability 1.12 %(4842.94 km2) has low suitability and 41.34 % (178950.35 km2) of the study area is not suitable for wind hydrogen production. By applying the constraints about 4 stations are suitable for wind-powered hydrogen refuelling system retrofitting in Adrar province.
The Impact of Hydrogen Admixture into Natural Gas on Residential and Commercial Gas Appliances
Jan 2022
Publication
Hydrogen as a carbon-free fuel is commonly expected to play a major role in future energy supply e.g. as an admixture gas in natural gas grids. Which impacts on residential and commercial gas appliances can be expected due to the significantly different physical and chemical properties of hydrogen-enriched natural gas? This paper analyses and discusses blends of hydrogen and natural gas from the perspective of combustion science. The admixture of hydrogen into natural gas changes the properties of the fuel gas. Depending on the combustion system burner design and other boundary conditions these changes may cause higher combustion temperatures and laminar combustion velocities while changing flame positions and shapes are also to be expected. For appliances that are designed for natural gas these effects may cause risk of flashback reduced operational safety material deterioration higher nitrogen oxides emissions (NOx) and efficiency losses. Theoretical considerations and first measurements indicate that the effects of hydrogen admixture on combustion temperatures and the laminar combustion velocities are often largely mitigated by a shift towards higher air excess ratios in the absence of combustion control systems but also that common combustion control technologies may be unable to react properly to the presence of hydrogen in the fuel.
Recovery Through Reform: Assessing the climate compatibility of Canada’s COVID-19 response in 2020
Feb 2021
Publication
Governments around the world are leveraging unprecedented amounts of capital to respond to the pandemic and bailing out struggling industries. Trends in energy-related spending indicate that despite the green push the world’s largest economies have still favoured fossil energy over clean energy.<br/><br/>We evaluate energy-related spending in Canada in 2020 (since the onset of COVID-19) using data from the Energy Policy Tracker. Trends in Canada are then compared to flagship policies in key jurisdictions with recent progressive climate policy announcements including France Germany and the United Kingdom. The brief ends with broad recommendations on how Canada can better align its recovery funding with climate action and fossil fuel subsidy reform.<br/><br/>This brief is one of three International Institute for Sustainable Development (IISD) policy briefs in its Recovery Through Reform series which assesses how efforts to achieve a green recovery from COVID-19 in Canada rely on—and can contribute to—fossil fuel subsidy reform.
Uncovering the True Cost of Hydrogen Production Routes Using Life Cycle Monetisation
Oct 2020
Publication
Hydrogen has been identified as a potential energy vector to decarbonise the transport and chemical sectors and achieve global greenhouse gas reduction targets. Despite ongoing efforts hydrogen technologies are often assessed focusing on their global warming potential while overlooking other impacts or at most including additional metrics that are not easily interpretable. Herein a wide range of alternative technologies have been assessed to determine the total cost of hydrogen production by coupling life-cycle assessments with an economic evaluation of the environmental externalities of production. By including monetised values of environmental impacts on human health ecosystem quality and resources on top of the levelised cost of hydrogen production an estimation of the “real” total cost of hydrogen was obtained to transparently rank the alternative technologies. The study herein covers steam methane reforming (SMR) coal and biomass gasification methane pyrolysis and electrolysis from renewable and nuclear technologies. Monetised externalities are found to represent a significant percentage of the total cost ultimately altering the standard ranking of technologies. SMR coupled with carbon capture and storage emerges as the cheapest option followed by methane pyrolysis and water electrolysis from wind and nuclear. The obtained results identify the “real” ranges for the cost of hydrogen compared to SMR (business as usual) by including environmental externalities thereby helping to pinpoint critical barriers for emerging and competing technologies to SMR.
A Hydrogen Strategy for a Climate-neutral Europe
Jul 2020
Publication
In an integrated energy system hydrogen can support the decarbonisation of industry transport power generation and buildings across Europe. The EU Hydrogen Strategy addresses how to transform this potential into reality through investments regulation market creation and research and innovation.
Hydrogen can power sectors that are not suitable for electrification and provide storage to balance variable renewable energy flows but this can only be achieved with coordinated action between the public and private sector at EU level. The priority is to develop renewable hydrogen produced using mainly wind and solar energy. However in the short and medium term other forms of low-carbon hydrogen are needed to rapidly reduce emissions and support the development of a viable market.
This gradual transition will require a phased approach:
Hydrogen can power sectors that are not suitable for electrification and provide storage to balance variable renewable energy flows but this can only be achieved with coordinated action between the public and private sector at EU level. The priority is to develop renewable hydrogen produced using mainly wind and solar energy. However in the short and medium term other forms of low-carbon hydrogen are needed to rapidly reduce emissions and support the development of a viable market.
This gradual transition will require a phased approach:
- From 2020 to 2024 we will support the installation of at least 6 gigawatts of renewable hydrogen electrolysers in the EU and the production of up to one million tonnes of renewable hydrogen.
- From 2025 to 2030 hydrogen needs to become an intrinsic part of our integrated energy system with at least 40 gigawatts of renewable hydrogen electrolysers and the production of up to ten million tonnes of renewable hydrogen in the EU.
- From 2030 to 2050 renewable hydrogen technologies should reach maturity and be deployed at large scale across all hard-to-decarbonise sectors.
- To help deliver on this Strategy the Commission is launched the European Clean Hydrogen Alliance with industry leaders civil society national and regional ministers and the European Investment Bank. The Alliance will build up an investment pipeline for scaled-up production and will support demand for clean hydrogen in the EU.
Effect of the Time Dependent Loading of Type IV Cylinders Using a Multi-scalemodel
Sep 2019
Publication
The current requirements for composite cylinders are still based on an arbitrary approach derived from the behaviour of metal structures that the designed burst pressure should be at least 2.5 times the maximum in-service pressure. This could lead to an over-designed composite cylinder for which the weight saving would be less than optimum. Moreover predicting the lifetime of composite cylinders is a challenging task due to their anisotropic characteristics. A federal research institute in Germany (BAM) has proposed a minimum load-cycle requirement that mitigates this issue by using a MonteCarlo analysis of the burst test results. To enrich this study more experiments are required however they are normally limited by the necessity of long duration testing times (loading rate and number of cylinders) and the design (stacking sequence of the composite layer). A multi-scale model incorporating the micromechanical behaviour of composite structures has been developed at Mines ParisTech. The model has shown similar behaviour to that of composite cylinders under different loading rates. This indicates that the model could assist the Monte-Carlo analysis study. An evaluation of the multi-scale model therefore has been carried out to determine its limitations in predicting lifetimes of composite cylinders. The evaluation starts with the comparison of burst pressures with type IV composite cylinders under different loading rates. A μCT-Scan of a type IV cylinder has been carried out at the University of Southampton. The produced images were analysed using the Fast-Fourier Transform (FFT) technique to determine the configuration of the composite layers which is required by the model. Finally the time dependent effect studied by using the multi scale model has been described. In the long-term this study can be used to conduct a parametric study for creating more efficient design of type IV cylinders.
Can Industry Keep Gas Distribution Networks Alive? Future Development of the Gas Network in a Decarbonized World: A German Case Study
Dec 2022
Publication
With the growing need for decarbonization the future gas demand will decrease and the necessity of a gas distribution network is at stake. A remaining industrial gas demand on the distribution network level could lead to industry becoming the main gas consumer supplied by the gas distribution network leading to the question: can industry keep the gas distribution network alive? To answer this research question a three-stage analysis was conducted starting from a rough estimate of average gas demand per production site and then increasing the level of detail. This paper shows that about one third of the German industry sites investigated are currently supplied by the gas distribution network. While the steel industry offers new opportunities the food and tobacco industry alone cannot sustain the gas distribution network by itself.
Dynamic System Modeling of Thermally-integrated Concentrated PV-electrolysis
Feb 2021
Publication
Understanding the dynamic response of a solar fuel processing system utilizing concentrated solar radiation and made of a thermally-integrated photovoltaic (PV) and water electrolyzer (EC) is important for the design development and implementation of this technology. A detailed dynamic non-linear process model is introduced for the fundamental system components (i.e. PV EC pump etc.) in order to investigate the coupled system behavior and performance synergy notably arising from the thermal integration. The nominal hydrogen production power is ∼2 kW at a hydrogen system efficiency of 16–21% considering a high performance triple junction III-V PV module and a proton exchange membrane EC. The device operating point relative to the maximum power point of the PV was shown to have a differing influence on the system performance when subject to temperature changes. The non-linear coupled behavior was characterised in response to step changes in water flowrate and solar irradiance and hysteresis of the current-voltage operating point was demonstrated. Whilst the system responds thermally to changes in operating conditions in the range of 0.5–2 min which leads to advantageously short start-up times a number of control challenges are identified such as the impact of pump failure electrical PV-EC disconnection and the potentially damaging accentuated temperature rise at lower water flowrates. Finally the simulation of co-generation of heat and hydrogen for various operating conditions demonstrates the significant potential for system efficiency enhancements and the required development of control strategies for demand matching is discussed.
Catalytic Effect of MoS2 on Hydrogen Storage Thermodynamics and Kinetics of an As-milled YMg11Ni Alloy
Jul 2017
Publication
In this study YMg11Ni and YMg11Ni + 5 wt% MoS2 (named YMg11Ni–MoS2) alloys were prepared by mechanical milling to examine the effect of adding MoS2 on the hydrogen storage performance of a Y–Mg–Ni-based alloy. The as-cast and milled alloys were tested to identify their structures by X-ray diffraction and transmission electron microscopy. The isothermal hydrogen storage thermodynamics and dynamics were identified through an automatic Sieverts apparatus and the non-isothermal dehydrogenation performance was investigated by thermogravimetry and differential scanning calorimetry. The dehydrogenation activation energy was calculated by both Arrhenius and Kissinger methods. Results revealed that adding MoS2produces a very slight effect on hydrogen storage thermodynamics but causes an obvious reduction in the hydrogen sorption and desorption capacities because of the deadweight of MoS2. The addition of MoS2significantly enhances the dehydrogenation performance of the alloy such as lowering dehydrogenation temperature and enhancing dehydrogenation rate. Specifically the initial desorption temperature of the alloy hydride lowers from 549.8 K to 525.8 K. The time required to desorb hydrogen at 3 wt% H2 is 1106 456 363 and 180 s corresponding to hydrogen desorption temperatures at 593 613 633 and 653 K for the YMg11Ni alloy and 507 208 125 and 86 s at identical conditions for the YMg11Ni–5MoS2 alloy. The dehydrogenation activation energy (Ea) values with and without added MoS2are 85.32 and 98.01 kJ mol−1. Thus a decrease in Ea value by 12.69 kJ mol−1 occurs and is responsible for the amelioration of the hydrogen desorption dynamics by adding a MoS2 catalyst.
A Probabilistic Framework for the Techno-economic Assessment of Smart Energy Hubs for Electric Vehicle Charging
Apr 2022
Publication
Smart energy hubs (Smart Hubs) equipped with Vehicle-to-Grid (V2G) charging photovoltaic (PV) energy generation and hydrogen storage capabilities are an emerging technology with potential to alleviate the impact of electric vehicles (EV) on the electricity grid. Their operation however is characterised by intermittent PV energy generation as well as uncertainties in EV traffic and driver preference. These uncertainties when combined with the need to maximise their financial return while guaranteeing driver satisfaction yields a challenging decision-making problem. This paper presents a novel Monte-Carlo-based modelling and computational framework for simulating the operation of Smart Hubs — providing a means for a holistic assessment of their technical and financial viability. The framework utilises a compact and representative mathematical model accounting for power losses PV module degradation variability in EV uptake price inflation driver preference and diversity in charge points and EVs. It provides a comprehensive approach for dealing with uncertainties and dependencies in EV data while being built on an energy management algorithm that maximises revenue generation ensures driver satisfaction and preserves battery life. The energy management problem is formulated as a mixed-integer linear programming problem constituting a business case that includes an adequate V2G reward model for drivers. To demonstrate its applicability the framework was used to assess the financial viability of a fleet management site for various caps on vehicle stay at the site. From the assessment controlled charging was found to be more financially rewarding in all cases yielding between 1.7% and 3.1% more revenue than uncontrolled charging. The self-consumption of the site was found to be nearly 100% due mainly to local load shifting and dispatchable hydrogen generation. V2G injection was however negligible — suggesting its unattractiveness for sites that do not participate in the demand side response market. Overall the numerical results obtained validate the applicability of the proposed framework as a decision-support tool in the sustainable design and operation of Smart Hubs for EV charging.
Study on the Use of Fuel Cells and Hydrogen in the Railway Environment
Jun 2019
Publication
This study outlines a pathway for commercialisation of stationary fuel cells in distributed generation across Europe. It has been sponsored by the Fuel Cells and Hydrogen Joint Undertaking (FCH JU) a public-private partnership between the European Commission the fuel cell and hydrogen industry and a number of research bodies and associations. The FCH JU supports research technology development and demonstration activities in the field of fuel cell and hydrogen technologies in Europe. The study explores how stationary fuel cells can benefit users how they can be brought to the market what hurdles still exist and how their diffusion may foster Europe's transition into a new energy age.
Sector Coupling Potential of Wind-based Hydrogen Production and Fuel Cell Train Operation in Regional Rail Transport in Berlin and Brandenburg
Jan 2021
Publication
As the transport sector is ought to be decarbonized fuel-cell-powered trains are a viable zero-tailpipe technology alternative to the widely employed diesel multiple units in regional railway service on non-electrified tracks. Carbon-free hydrogen can be provided by water-electrolysis from renewable energies. In this study we introduce an approach to assess the potential of wind-based hydrogen for use in adjacent regional rail transport by applying a GIS approach in conjunction with a site-level cost model. In Brandenburg about 10.1 million train-km annually could be switched to fuel cell electric train operation. This relates to a diesel consumption of appr. 9.5 million liters today. If fuel cell trains would be employed that translated to 2198 annual tons hydrogen annually. At favorable sites hydrogen costs of approx. 6.40 €/kg - including costs of hydrogen refueling stations - could be achieved. Making excess hydrogen available for other consumers would further decrease hydrogen production costs.
Technical Feasibility of Low Carbon Heating in Domestic Buildings
Dec 2020
Publication
Scotland’s Climate Change Plan set an ambition for emissions from buildings to be near zero by 2050 and targets 35% of domestic and 70% of non-domestic buildings’ heat to be supplied using low carbon technologies by 2032. The Climate Change (Emissions Reduction Targets) (Scotland) Act 2019 set a new target for emissions to be net zero by 2045 with interim targets of 75% by 2030 and 90% by 2040. The update to the Climate Change Plan will be published at the end of 2020 to reflect these new targets. The Energy Efficient Scotland programme launched in May 2018 sets out a wide range of measures to promote low carbon heating alongside energy efficiency improvements in Scotland’s buildings. Meeting these targets will require almost all households in Scotland to change the way they heat their homes. It is therefore imperative to advance our understanding of the suitability of the available low carbon heating options across Scotland’s building stock.<br/><br/>The aim of this work is to assess the suitability of low carbon heating technologies in residential buildings in Scotland. The outputs generated through this work will form a key part of the evidence base on low carbon heat which the Scottish Government will use to further develop and strengthen Scotland’s low carbon heat policy in line with the increased level of ambition of achieving Net Zero by 2045.
Numerical Analysis for Hydrogen Flame Acceleration during a Severe Accident in the APR1400 Containment Using a Multi-Dimensional Hydrogen Analysis System
Nov 2020
Publication
Korea Atomic Energy Research Institute (KAERI) established a multi-dimensional hydrogen analysis system to evaluate hydrogen release distribution and combustion in the containment of a Nuclear Power Plant (NPP) using MAAP GASFLOW and COM3D. In particular KAERI developed an analysis methodology for a hydrogen flame acceleration on the basis of the COM3D validation results against measured data of the hydrogen combustion tests in the ENACCEF and THAI facilities. The proposed analysis methodology accurately predicted the peak overpressure with an error range of approximately ±10% using the Kawanabe model used for a turbulent flame speed in the COM3D. KAERI performed a hydrogen flame acceleration analysis using the multi-dimensional hydrogen analysis system for a severe accident initiated by a station blackout (SBO) under the assumption of 100% metal–water reaction in the Reactor Pressure Vessel (RPV) to evaluate an overpressure buildup in the containment of the Advanced Power Reactor 1400 MWe (APR1400). The magnitude of the overpressure buildup in the APR1400 containment might be used as a criterion to judge whether the containment integrity is maintained or not when the hydrogen combustion occurs during a severe accident. The COM3D calculation results using the established analysis methodology showed that the calculated peak pressure in the containment was lower than the fracture pressure of the APR1400 containment. This calculation result might have resulted from a large air volume of the containment a reduced hydrogen concentration owing to passive auto-catalytic recombiners installed in the containment during the hydrogen release from the RPV and a lot of stem presence during the hydrogen combustion period in the containment. Therefore we found that the current design of the APR1400 containment maintained its integrity when the flame acceleration occurred during the severe accident initiated by the SBO accident.
FCH JU – Key to Sustainable Energy and Transport
Jan 2019
Publication
This brochure offers an overview of the main applications of fuel cell and hydrogen technologies and how they work and provides insights into our programme and our accomplishments.
Vented Hydrogen-air Deflagrations in Low Strength Equipment and Buildings
Sep 2013
Publication
This paper aims to improve prediction capability of the vent sizing correlation presented in the form of functional dependence of the dimensionless deflagration overpressure on the turbulent Bradley number similar to our previous studies. The correlation is essentially upgraded based on recent advancements in understanding and modelling of combustion phenomena relevant to hydrogen-air vented deflagrations and unique large-scale tests carried out by different research groups. The focus is on hydrogen-air deflagrations in low-strength equipment and buildings when the reduced pressure is accepted to be below 0.1 MPa. The combustion phenomena accounted for by the correlation include: turbulence generated by the flame front itself; leading point mechanism stemming from the preferential diffusion of hydrogen in air in stretched flames; growth of the fractal area of the turbulent flame surface; initial turbulence in the flammable mixture; as well as effects of enclosure aspect ratio and presence of obstacles. The correlation is validated against the widest range of experimental conditions available to date (76 experimental points). The validation covers a wide range of test conditions: different shape enclosures of volume up to 120 m3; initially quiescent and turbulent hydrogen-air mixtures; hydrogen concentration in air from 6% to 30% by volume; ignition source location at enclosure centre near and far from a vent; empty enclosures and enclosures with obstacles.
Business Models for Low Carbon Hydrogen Production: A Report for BEIS
Aug 2020
Publication
Low carbon hydrogen could have a significant role to play in meeting the UK’s Net Zero target: the Committee on Climate Change (CCC) estimates that up to 270TWh of low carbon hydrogen could be needed in its ‘Further Ambition’ scenario. However at present there is no large-scale production of low carbon hydrogen in the UK not least as it is more costly than most high carbon alternatives. For hydrogen to be the viable option envisaged by the CCC projects may need to be deployed from the 2020s.<br/>BEIS has commissioned Frontier Economics to develop business models to support low carbon hydrogen production. This report builds on the earlier Carbon Capture Usage and Storage (CCUS) business models consultation2 and develops business models for BEIS to consider further. This report is a milestone in BEIS’ longer term process of developing hydrogen business models. It forms a part of BEIS’ wider research into a range of decarbonisation options across the economy.<br/>Further analysis will be required before a final decision is made.
Highly Resolve Large Eddy Simulations of a Transitional Air-helium Buoyant Jet in a Two Vented Enclosure: Validation Against Particle Image Velocimetry Experiments
Sep 2017
Publication
The article deals with LES simulations of an air-helium buoyant jet in a two vented enclosure and their validation against particle image velocimetry experiments. The main objective is to test the ability of LES models to simulate such scenarios. These types of scenarios are of first interest considering safety studies for new hydrogen systems. Three main challenges are identified. The two first are the ability of the LES model to account for a rapid laminar-to-turbulence transition mainly due to the buoyancy accelerations and the Rayleigh-Taylor instabilities that can develop due to sharp density gradients. The third one is the outlet boundary conditions to be imposed on the vent surfaces. The influence of the classical pressure boundary condition is studied by comparing the simulations results when an exterior region is added in the simulations. The comparisons against particle image velocimetry experiments show that the use of an exterior domain gives more accurate results than the classical pressure boundary condition. This result and the description of the phenomena involved are the main outlets of the article.
Hydrogen Venting Under Variable Flow Conditions
Sep 2011
Publication
Safety distances for hydrogen plumes are currently derived using models developed for hydrocarbon releases. It is well known that hydrogen behaves in a significantly different manner to that of hydrocarbons when released to atmosphere. There are two main aspects involved with the development of safety distances for credible hydrogen releases; the intensity of the thermal radiation from such a plume should it be ignited and the distance downwind from the release point to the point where a flammable mixture with air no longer exists. A number of distinct areas of venting behaviour were investigated; Thermal radiation from ignited plumes from vertical open ended vent pipes Far field radiation measurements for direct comparison with models Thermal radiation from ignited plumes from vertical vent pipes terminating in a T-piece Thermal radiation measurements from ignited hydrogen with a 45 vent termination Hydrogen concentration measurements with a T-piece.
Well-to-wheel Greenhouse Gas Emissions of Heavy-duty Transports: Influence of Electricity Carbon Intensity
Feb 2021
Publication
There are several alternatives for how to phase out diesel in heavy-duty transports thereby reducing the sector’s climate change impact. This paper assesses the well-to-wheel (WTW) greenhouse gas (GHG) emissions of energy carriers for heavy-duty vehicles analyzing the effect of the carbon intensity of the electricity used in production. The results show that energy carriers with high electricity dependence are not necessarily better than diesel from a WTW perspective. In particular fuels produced through electrolysis are not well suited in carbon-intense electricity systems. Conversely waste-based biofuels have low GHG emissions regardless of the electricity system. Battery-electric buses show a large reduction of GHG emissions compared to diesel buses and many other alternatives while battery-electric trucks have higher GHG emissions than diesel in carbon intense electricity systems. Thus electrifying transports or switching to renewable fuels will not suffice if the electricity system is not made renewable first.
High-Order Perturbation Solutions to a Lh2 Spreading Model With Continuous Spill
Sep 2011
Publication
High-order perturbation solutions have been obtained for the simple physical model describing the LH2 spreading with a continuous spill and are shown to improve over the first-order perturbation solutions. The non-dimensional governing equations for the model are derived to obtain more general solutions. Non-dimensional parameters are sought as the governing parameters for the non-dimensional equations and the non-dimensional evaporation rate is used as the perturbation parameter. The results show that the second-order solutions exhibit an improvement over the first-order solutions with respect to the pool volume; however there is still a difference between numerical solutions and second-order solutions in the late stage of spread. Finally it is revealed that the third-order solutions almost agree with numerical solutions.
A Pathway to Decarbonise the Shipping Sector by 2050
Oct 2021
Publication
Urgent action is needed to accelerate the pace of the global energy transition and the decarbonisation of the global economy. International shipping is a key sector of the economy as much as 90% of worldwide trade is transacted via ocean going vessels. The sector is also one of the most challenging to decarbonise.
In this context A Pathway to Decarbonise the Shipping Sector by 2050 by the International Renewable Energy Agency (IRENA) analyses the technology readiness of the renewable fuels suitable for international shipping. This report also explores the options and actions needed to progress towards a decarbonised maritime shipping sector by 2050 and seeks to identify a realistic mitigation pathway to reach the climate goal of limiting global temperature rise to 1.5°C and bringing CO2 emissions closer to net zero by mid-century.
Key messages:
In this context A Pathway to Decarbonise the Shipping Sector by 2050 by the International Renewable Energy Agency (IRENA) analyses the technology readiness of the renewable fuels suitable for international shipping. This report also explores the options and actions needed to progress towards a decarbonised maritime shipping sector by 2050 and seeks to identify a realistic mitigation pathway to reach the climate goal of limiting global temperature rise to 1.5°C and bringing CO2 emissions closer to net zero by mid-century.
Key messages:
- The sector’s decarbonisation strategy must involve a combination of energy efficiency and renewable fuels. Starting now the active adoption of energy efficiency measures will be critical to reduce energy demand and thus CO2 emissions in the immediate term.
- In the short term advanced biofuels will play a key role in the reduction of CO2 emissions. In the medium and long-term green hydrogen-based fuels are set to be the backbone for the sector’s decarbonisation.
- Renewable e-ammonia will play a pivotal role; where 183 million tonnes of renewable ammonia for international shipping alone will be needed by 2050 - a comparable amount to today’s ammonia global production.
- While renewable fuels production costs are currently high in the next decades renewable fuels will become cost competitive and can shield the shipping sector from the volatility that characterises the fossil fuels market.
- Taking early action is vital. Sector decarbonisation can be accelerated and ambition raised beyond the climate goals by fostering investment in the production of renewable fuels. Stakeholders need to develop broader business models and establish strategic partnerships involving energy-intensive industries as well as power suppliers and the petrochemical sector.
Hydrogen Risk Assessment in Sao Paulo State, Brazil
Sep 2011
Publication
Sao Paulo State Environmental Protection Agency CETESB Brazil adopts a so called Reference Distance (RD) from hazardous substances storage facilities to populated places as a decision making tool for the application of a simplified or a full Risk Analysis (RA). As for hydrogen RD was set up based on instantaneous release scenarios where consequences reaching off-site population were estimated for delayed ignition ending up in vapor cloud explosion (VCE) with a 0.1 bar blast wave overpressure as a chosen endpoint corresponding to a 1%2of death probability range. Procedures for RD evaluation and further adoption by CETESB are presented in this paper.
Analysis of Acoustic Pressure Oscillation During Vented Deflagration
Oct 2015
Publication
In industrial buildings explosion relief panels or doors are often used to reduce damages caused by gas explosion. Decades of research produced a significant contribution to the understanding of the phenomena involved nevertheless among the aspects that need further research interaction between acoustic oscillation and the flame front is one of the more important. Interaction between the flame front and acoustic oscillation has raised technical problem in lots of combustion applications as well and had been studied theoretically and experimentally in such cases. Pressure oscillation had been observed in vented deflagration and in certain cases they are responsible for the highest pressure peak generated during the event. At Scalbatraio laboratory of Pisa University CVE test facility was built in order to investigate vented hydrogen deflagration. This paper is aimed to present an overview of the results obtained during several experimental campaigns which tests are analysed with the focus on the investigation of flame acoustic interaction phenomenon. Qualitative and quantitative analysis is presented and the possible physic generating the phenomenon investigated.
Risk Informed Separation Distances For Hydrogen Refuelling Stations
Sep 2011
Publication
The lay-out requirements developed for hydrogen systems operated in industrial environment are not suitable for the operating conditions specific to hydrogen refuelling stations (service pressure of up to 95 MPa facility for public use). A risk informed rationale has been developed to define and substantiate separation distance requirements in ISO 20100 Gaseous hydrogen – refuelling stations [1]. In this approach priority is given to preventing escalation of small incidents into majors ones with a focus on critical exposures such as places of occupancy (fuelling station retail shop) while optimizing use of the available space from a risk perspective a key objective for being able to retrofit hydrogen refuelling in existing stations.
The Hydrogen Storage Properties of MgH2–Fe7S8 Composites
Nov 2020
Publication
Nanostructured Fe7S8 was successfully synthesized and its catalytic effect on hydrogen absorption/desorption performance of MgH22 is systemically discussed. The MgH2 + 16.7 wt% Fe7S8 composite prepared by ball-milling method offers a striking catalytic activity for hydrogenation kinetics and also reduces the initial decomposition temperature for MgH22. The composite of MgH2–Fe7S8 can absorb 4.000 wt% of hydrogen within 1800 s at 473 K which is about twice that of pristine MgH2 (1.847 wt%) under the same conditions. The onset hydrogen release temperature of Fe7S8-modified MgH2 is 420 K which is 290 K lower than that of additive-free MgH2 (710 K). Meanwhile the doped sample could release 4.403 wt% of hydrogen within 1800 s at 623 K as compared to 2.479 wt% of hydrogen by MgH2. The activation energy for MgH2–Fe7S8 is about 130.0 kJ mol−1 approximately 36 kJ mol−1 lower than that of MgH2. The hydriding process of MgH2 + 16.7 wt% Fe7S8 follows the nucleation and growth mechanism. The prominent hydrogen storage performances are related to the reactions between MgH2 and Fe7S8. The newly formed MgS and Fe in the ball-milling process present a co-catalytic effect on the hydrogen storage performance of MgH22.
Department of Energy Hydrogen Program Plan
Nov 2020
Publication
The Department of Energy (DOE) Hydrogen Program Plan (the Program Plan or Plan) outlines the strategic high-level focus areas of DOE’s Hydrogen Program (the Program). The term Hydrogen Program refers not to any single office within DOE but rather to the cohesive and coordinated effort of multiple offices that conduct research development and demonstration (RD&D) activities on hydrogen technologies. This terminology and the coordinated efforts on hydrogen among relevant DOE offices have been in place since 2004 and provide an inclusive and strategic view of how the Department coordinates activities on hydrogen across applications and sectors. This version of the Plan updates and expands upon previous versions including the Hydrogen Posture Plan and the DOE Hydrogen and Fuel Cells Program Plan and provides a coordinated high-level summary of hydrogen related activities across DOE.
The 2006 Hydrogen Posture Plan fulfilled the requirement in the Energy Policy Act of 2005 (EPACT 2005) that the Energy Secretary transmit to Congress a coordinated plan for DOE’s hydrogen and fuel cell activities. For historical context the original Posture Plan issued in 2004 outlined a coordinated plan for DOE and the U.S. Department of Transportation to meet the goals of the Hydrogen Fuel Initiative (HFI) and implement the 2002 National Hydrogen Energy Technology Roadmap. The HFI was launched in 2004 to accelerate research development and demonstration (RD&D) of hydrogen and fuel cell technologies for use in transportation electricity generation and portable power applications. The Roadmap provided a blueprint for the public and private efforts required to fulfill a long-term national vision for hydrogen energy as outlined in A National Vision of America’s Transition to a Hydrogen Economy—to 2030 and Beyond. Both the Roadmap and the Vision were developed out of meetings involving DOE industry academia non-profit organizations and other stakeholders. The Roadmap the Vision the Posture Plans the 2011 Program Plan and the results of key stakeholder workshops continue to form the underlying basis for this current edition of the Program Plan.
This edition of the Program Plan reflects the Department’s focus on conducting coordinated RD&D activities to enable the adoption of hydrogen technologies across multiple applications and sectors. It includes content from the various plans and documents developed by individual offices within DOE working on hydrogen-related activities including: the Office of Fossil Energy's Hydrogen Strategy: Enabling a Low Carbon Economy the Office of Energy Efficiency and Renewable Energy’s Hydrogen and Fuel Cell Technologies Office Multi-year RD&D Plan the Office of Nuclear Energy’s Integrated Energy Systems 2020 Roadmap and the Office of Science’s Basic Research Needs for the Hydrogen Economy. Many of these documents are also in the process of updates and revisions and will be posted online.
Through this overarching document the reader will gain information on the key RD&D needs to enable the largescale use of hydrogen and related technologies—such as fuel cells and turbines—in the economy and how the Department’s various offices are addressing those needs. The Program will continue to periodically revise the Plan along with all program office RD&D plans to reflect technological progress programmatic changes policy decisions and updates based on stakeholder input and reviews.
The 2006 Hydrogen Posture Plan fulfilled the requirement in the Energy Policy Act of 2005 (EPACT 2005) that the Energy Secretary transmit to Congress a coordinated plan for DOE’s hydrogen and fuel cell activities. For historical context the original Posture Plan issued in 2004 outlined a coordinated plan for DOE and the U.S. Department of Transportation to meet the goals of the Hydrogen Fuel Initiative (HFI) and implement the 2002 National Hydrogen Energy Technology Roadmap. The HFI was launched in 2004 to accelerate research development and demonstration (RD&D) of hydrogen and fuel cell technologies for use in transportation electricity generation and portable power applications. The Roadmap provided a blueprint for the public and private efforts required to fulfill a long-term national vision for hydrogen energy as outlined in A National Vision of America’s Transition to a Hydrogen Economy—to 2030 and Beyond. Both the Roadmap and the Vision were developed out of meetings involving DOE industry academia non-profit organizations and other stakeholders. The Roadmap the Vision the Posture Plans the 2011 Program Plan and the results of key stakeholder workshops continue to form the underlying basis for this current edition of the Program Plan.
This edition of the Program Plan reflects the Department’s focus on conducting coordinated RD&D activities to enable the adoption of hydrogen technologies across multiple applications and sectors. It includes content from the various plans and documents developed by individual offices within DOE working on hydrogen-related activities including: the Office of Fossil Energy's Hydrogen Strategy: Enabling a Low Carbon Economy the Office of Energy Efficiency and Renewable Energy’s Hydrogen and Fuel Cell Technologies Office Multi-year RD&D Plan the Office of Nuclear Energy’s Integrated Energy Systems 2020 Roadmap and the Office of Science’s Basic Research Needs for the Hydrogen Economy. Many of these documents are also in the process of updates and revisions and will be posted online.
Through this overarching document the reader will gain information on the key RD&D needs to enable the largescale use of hydrogen and related technologies—such as fuel cells and turbines—in the economy and how the Department’s various offices are addressing those needs. The Program will continue to periodically revise the Plan along with all program office RD&D plans to reflect technological progress programmatic changes policy decisions and updates based on stakeholder input and reviews.
A Study of Hydrogen Flame Length with Complex Nozzle Geometry
Sep 2017
Publication
The growing number of hydrogen fillings stations and cars increases the need for accurate models to determine risk. The effect on hydrogen flame length was measured by varying the diameter of the spouting nozzle downstream from the chocked nozzle upstream. The results was compared with an existing model for flame length estimations. The experimental rig was setup with sensors that measured accurately temperature mass flow heat radiation and the pressure range from 0.1 to 11 MPa. The flame length was determined with an in-house developed image-processing tool which analyzed a high-speed film of the each experiment. Results show that the nozzle geometry can cause a deviation as high as 50% compared to estimated flame lengths by the model if wrong assumptions are made. Discharge coefficients for different nozzles has been calculated and presented.
Workshop Report: Summary & Outcomes, Putting Science into Standards Power-to-Hydrogen and HCNG
Oct 2014
Publication
The Joint Research Centre (JRC) of the European Commission together with the European Association of Research and Technology Organisations (EARTO) the European Standards Organisations (ESO) CEN and CENELEC and the European Commission Directorate-General Enterprise and Industry (ENTR) have launched an initiative within the context of the European Forum on Science and Industry to bring the scientific and standardization communities closer together. The second and very successful workshop in a series entitled “Putting Science into Standards" was held in at the Institute for Energy and Transport of the JRC in Petten on 21-22 October 2014.<br/>The workshop focused on Power to Hydrogen (P2H) and Hydrogen Compressed Natural Gas (HCNG) which represent a promising and major contribution to the challenging management of increased integration of renewable energy sources in the overall energy system. The workshop offered a platform to exchange ideas on technologies policy and standardization issues. The participation of major stakeholders from both industry and research to this event proved fruitful in moving towards consensus on the relevant technical issues involved and at identifying a common way forward to increase the maturity and market visibility of P2H components and systems. Other outcomes include a clarification of expectations of industry of where and how policy and standardization can contribute to a competitive development of P2H and related issues. The workshop results will be used to devise a roadmap on "Opportunities for Power to Hydrogen and HCNG" by CEN/CENELEC outlining the next steps of standardization activities.
Numerical and Experimental Investigation of H2-air and H2-O2 Detonation Parameters in a 9 m Long Tube, Introduction of a New Detonation Model
Sep 2017
Publication
Experimental and numerical investigation of hydrogen-air and hydrogen-oxygen detonation parameters was performed. A new detonation model was introduced and validated against the experimental data. Experimental set-up consisted of 9 m long tube with 0.17 m in diameter where pressure was measured with piezoelectric transducers located along the channel. Numerical simulations were performed within OpenFoam code based on progress variable equation where the detonative source term accounts for autoignition effects. Autoignition delay times were computed at a simulation run-time with the use of a multivariate regression model where independent variables were: pressure temperature and fuel concentration. The dependent variable was the autoignition delay time. Range of the analyzed gaseous mixture composition varied between 20% and 50% of hydrogen-air and 50%–66% of hydrogen in oxygen. Simulations were performed using LES one-equation eddy viscosity turbulence model in 2D and 3D. Calculations were validated against experimental data.
Comparison Between Carbon Molecular Sieve and Pd-Ag Membranes in H2-CH4 Separation at High Pressure
Aug 2020
Publication
From a permeability and selectivity perspective supported thin-film Pd–Ag membranes are the best candidates for high-purity hydrogen recovery for methane-hydrogen mixtures from the natural gas grid. However the high hydrogen flux also results in induced bulk-to-membrane mass transfer limitations (concentration polarization) especially when working at low hydrogen concentration and high pressure which further reduces the hydrogen permeance in the presence of mixtures. Additionally Pd is a precious metal and its price is lately increasing dramatically. The use of inexpensive CMSM could become a promising alternative. In this manuscript a detailed comparison between these two membrane technologies operating under the same working pressure and mixtures is presented.<br/>First the permeation properties of CMSM and Pd–Ag membranes are compared in terms of permeance and purity and subsequently making use of this experimental investigation an economic evaluation including capital and variable costs has been performed for a separation system to recover 25 kg/day of hydrogen from a methane-hydrogen mixture. To widen the perspective also a sensitivity analysis by changing the pressure difference membrane lifetime membrane support cost and cost of Pd/Ag membrane recovery has been considered. The results show that at high pressure the use of CMSM is to more economic than the Pd-based membranes at the same recovery and similar purity.
Hydrogen Energy
Feb 2007
Publication
The problem of anthropogenically driven climate change and its inextricable link to our global society’s present and future energy needs are arguably the greatest challenge facing our planet. Hydrogen is now widely regarded as one key element of a potential energy solution for the twenty-first century capable of assisting in issues of environmental emissions sustainability and energy security. Hydrogen has the potential to provide for energy in transportation distributed heat and power generation and energy storage systems with little or no impact on the environment both locally and globally. However any transition from a carbon-based (fossil fuel) energy system to a hydrogen-based economy involves significant scientific technological and socio-economic barriers. This brief report aims to outline the basis of the growing worldwide interest in hydrogen energy and examines some of the important issues relating to the future development of hydrogen as an energy vector.
Link to document download on Royal Society Website
Link to document download on Royal Society Website
Safety Concept of Nuclear Cogeneration of Hydrogen and Electricity
Oct 2015
Publication
There is a significant potential for nuclear combined heat and power (CHP) in quite a number of industries. The reactor concepts of the next generation would be capable to open up in particular the high temperature heat market where nuclear energy is applicable to the production processes of hydrogen (or liquid fuels) by steam reforming or water splitting. Due to the need to locate a nuclear facility near the hydrogen plant an overall safety concept has to deal with the question of safety of the combined nuclear/industrial system by taking into account a qualitatively new class of events characterized by interacting influences. Specific requirements will be determined by such factors as the reactor type the nature of the industrial process the separation distances of the industrial facility and population centers from the nuclear plant and prevailing public attitudes. Based on the Japanese concept of the GTHTR300C nuclear reactor for electricity and hydrogen cogeneration theoretical studies were conducted on the release dispersive transport and explosion of a hydrogen cloud in the atmosphere for the sake of assessing the required minimum separation distance to avoid any risk to the nuclear plant's safety systems. In the case of sulfur-iodine water splitting the accidental release of process intermediates including large amounts of sulfur dioxide sulfur trioxide and sulfuric acid need to be investigated as well to estimate the potential risk to nuclear installations like the operators' room and estimate appropriate separation distances against toxic gas propagation. Results of respective simulation studies will be presented.
Fuel Cell Electric Buses: Potential for Sustainable Public Transport in Europe
Oct 2015
Publication
This report provides an outlook for jointly achieving a commercialisation pathway.<br/>Building on the findings of the 2012 FCH JU technology study on alternative powertrains for urban buses this report provides an assessment of the commercialisation pathway from an operational perspective. It reflects the actual situation in which operators deploy large scale demonstration projects in the next years from a rather conservative angle and argues why it makes sense to deploy FC buses now. The insights are based on first-hand data and assessments of the coalition members from the hydrogen and fuel cell industry as well as local governments and public transport operators in Europe.
Numerical Simulations of Cryogenic Hydrogen Cooling in Vortex Tubes with Smooth Transitions
Mar 2021
Publication
Improving efficiency of hydrogen cooling in cryogenic conditions is important for the wider applications of hydrogen energy systems. The approach investigated in this study is based on a Ranque-Hilsch vortex tube (RHVT) that generates temperature separation in a working fluid. The simplicity of RHVT is also a valuable characteristic for cryogenic systems. In the present work novel shapes of RHVT are computationally investigated with the goal to raise efficiency of the cooling process. Specifically a smooth transition is arranged between a vortex chamber where compressed gas is injected and the main tube with two exit ports at the tube ends. Flow simulations have been carried out using STAR-CCM+ software with the real-gas Redlich-Kwong model for hydrogen at temperatures near 70 K. It is determined that a vortex tube with a smooth transition of moderate size manifests about 7% improvement of the cooling efficiency when compared vortex tubes that use traditional vortex chambers with stepped transitions and a no-chamber setup with direct gas injection.
Sensitive Intervention Points to Achieve Net-zero Emissions (Sixth Carbon Budget Policy Advisory Group)
Dec 2020
Publication
The group concluded that the transition to Net Zero can and will occur and will leave a positive legacy for future generations. They examined the UK as a complex adaptive system and identified recommendations for accelerating progress and reducing the risks of failure. The Group recognised an opportunity for Sensitive Intervention Points (SIPs) coinciding with these recommendations pointing to opportunities to accelerate a transition towards Net Zero by exploiting socio-economic tipping points.
These included:
These included:
- Deepening public engagement through investments to support measures to lower ‘thresholds’ to behavioural change such as energy efficiency or dietary alternatives. This can form part of a public engagement strategy for Net Zero that educates the public involves people in decision-making and provides trusted information at key decision points
- Delivering social justice via a clear long-term vision for specific regions coupled with mechanisms that reward the private sector for building industries in otherwise deprived areas starting now
- Government leading on Net Zero by requiring any company meeting with ministers and secretaries of state to have a plan to reach net zero emissions
- Leveraging global dynamics by introducing a border carbon adjustment and consider forming bilateral and multilateral preferential trading arrangements for environmental goods and services
- Penalising emissions by committing in the UK’s NDC to sequester 10% of CO2 emissions generated by fossil fuels and industry by 2030
- Increasing business ambition by identifying businesses that shape industries – celebrate and elevate them
- Accelerating technology via Pathfinder cities that can deliver comprehensive steps towards Net Zero and demonstrate the interactions required across complex systems of low-carbon electricity heat and transport
- Redirecting capital flows by introducing Net zero aligned and transparent accounting and auditing
- Harnessing legal avenues by legislating all regulators to regard the Paris Agreement Sixth Carbon Budget and 2050 Net Zero target in their duties.
Net Zero Public Dialogue
Mar 2021
Publication
This research project brought together members of the public from across the UK to participate in online workshops to explore:
- public understanding and perceptions of what reaching climate targets in the UK will mean for them individually and for society as a whole
- public attitudes and preferences towards the role that individual behaviour change should have in reaching net zero
- public perceptions of the easiest and toughest areas of change to help reach net zero
- public views on how they would prefer to engage with net zero policies and relevant initiatives that they feel could support the delivery of net zero
Are We Building Back Better? Evidence from 2020 and Pathways for Inclusive Green Recovery Spending
Mar 2021
Publication
COVID-19 has led to a global crisis threatening the lives and livelihoods of the most vulnerable by increasing poverty exacerbating inequalities and damaging long-term economic growth prospects. The report Are We Building Back Better? Evidence from 2020 and Pathways for Inclusive Green Recovery Spending provides an analysis of over 3500 fiscal policies announced by leading economies in 2020 and calls for governments to invest more sustainably and tackle inequalities as they stimulate growth in the wake of the devastation wrought by the pandemic.
UKERC Research Atlas Landscape – Fuel Cells
Dec 2013
Publication
This UKERC Research Atlas Landscape provides an overview of the competencies and publicly funded activities in fuel cell research development and demonstration (RD&D) in the UK. It covers the main funding streams research providers infrastructure networks and UK participation in international activities.
The Effects of Electrochemical Hydrogen Charging on Room-Temperature Tensile Properties of T92/TP316H Dissimilar Weldments in Quenched-and-Tempered and Thermally-Aged Conditions
Aug 2019
Publication
The influence of isothermal aging at 620 °C in combination with subsequent electrochemical hydrogen charging at room-temperature was studied on quenched-and-tempered T92/TP316H martensitic/austenitic weldments in terms of their room-temperature tensile properties and fracture behavior. Hydrogen charging of the weldments did not significantly affect their strength properties; however it resulted in considerable deterioration of their plastic properties along with significant impact on their fracture characteristics and failure localization. The hydrogen embrittlement plays a dominant role in degradation of the plastic properties of the weldments already in their initial material state i.e. before thermal aging. After thermal aging and subsequent hydrogen charging mutual superposition of thermal and hydrogen embrittlement phenomena had led to clearly observable effects on the welds deformation and fracture processes. The measure of hydrogen embrittlement was clearly lowered for thermally aged material state since the contribution of thermal embrittlement to overall degradation of the weldments has dominated. The majority of failures of the weldments after hydrogen charging occurred in the vicinity of T92 BM/Ni weld metal (WM) fusion zone; mostly along the Type-II boundary in Ni-based weld metal. Thus regardless of aging exposure the most critical failure regions of the investigated weldments after hydrogen charging and tensile straining at room temperature are the T92 BM/Ni WM fusion boundary and Type-II boundary acting like preferential microstructural sites for hydrogen embrittling effects accumulation
Effect of Initial Turbulence on Vented Explosion Over Pressures from Lean Hydrogen-air Deflagrations
Sep 2013
Publication
To examine the effect of initial turbulence on vented explosions experiments were performed for lean hydrogen–air mixtures with hydrogen concentrations ranging from 12 to 15% vol. at elevated initial turbulence. As expected it was found that an increase in initial turbulence increased the overall flame propagation speed and this increased flame propagation speed translated into higher peak overpressures during the external explosion. The peak pressures generated by flame–acoustic interactions however did not vary significantly with initial turbulence. When flame speeds measurements were examined it was found that the burning velocity increased with flame radius as a power function of radius with a relatively constant exponent over the range of weak initial turbulence studied and did not vary systematically with initial turbulence. Instead the elevated initial turbulence increased the initial flame propagation velocities of the various mixtures. The initial turbulence thus appears to act primarily by generating higher initial flame wrinkling while having a minimal effect on the growth rate of the wrinkles. For practical purposes of modelling flame propagation and pressure generation in vented explosions the increase in burning velocity due to turbulence is suggested to be approximated by a single constant factor that increases the effective burning velocity of the mixture. When this approach is applied to a previously developed vent sizing correlation the correlation performs well for almost all of the peaks. It was found however that in certain situations this approach significantly under predicts the flame–acoustic peak. This suggests that further research may be necessary to better understand the influence of initial turbulence on the development of flame–acoustic peaks in vented explosions.
Leakage-type-based Analysis of Accidents Involving Hydrogen Fueling Stations in Japan and USA
Aug 2016
Publication
To identify the safety issues associated with hydrogen fuelling stations incidents at such stations in Japan and the USA were analyzed considering the regulations in these countries. Leakage due to the damage and fracture of main bodies of apparatuses and pipes in Japan and the USA is mainly caused by design error that is poorly planned fatigue. Considering the present incidents in these countries adequate consideration of the usage environment in the design is very important. Leakage from flanges valves and seals in Japan is mainly caused by screw joints. If welded joints are to be used in hydrogen fuelling stations in Japan strength data for welded parts should be obtained and pipe thicknesses should be reduced. Leakage due to other factors e.g. external impact in Japan and the USA is mainly caused by human error. To realize self-serviced hydrogen fuelling stations safety measures should be developed to prevent human error by fuel cell vehicle users.
Measurements of Effective Diffusion Coefficient of Helium and Hydrogen Through Gypsum
Sep 2011
Publication
An experimental apparatus which was based on the ¼-scale garage previously used for studying helium release and dispersion in our laboratory was used to obtain effective diffusion coefficients of helium and hydrogen (released as forming gas for safety reasons) through gypsum panel. Two types of gypsum panel were used in the experiments. Helium or forming gas was released into the enclosure from a Fischer burner1 located near the enclosure floor for a fixed duration and then terminated. Eight thermal-conductivity sensors mounted at different vertical locations above the enclosure floor were used to monitor the temporal and spatial gas concentrations. An electric fan was used inside the enclosure to mix the released gas to ensure a spatially uniform gas concentration to minimize stratification. The temporal variations of the pressure difference between the enclosure interior and the ambience were also measured. An analytical model was developed to extract the effective diffusion coefficients from the experimental data.
Non-steady Characteristics of Dispersion and Ignitability for High-pressurized Hydrogen Jet Discharged From a Pinhole
Sep 2017
Publication
Hydrogen gas concentrations and jet velocities were measured downstream by a high response speed flame ionization detector and PIV (Particle Image Velocimetry) in order to investigate the characteristics of dispersion and ignitability for 40–82 MPa high-pressurized hydrogen jet discharged from a nozzle with 0.2 mm diameter. The light emitted from both OH radical and water vapor species yielded from hydrogen combustion ignited by an electric spark were recorded by two high speed cameras. From the results the empirical formula concerning the relationships for time-averaged concentrations concentration fluctuations and ignition probability were obtained to suggest that they would be independent of hydrogen discharge pressure.
Closing the Regulatory Gaps and Advancing Hydrogen Infrastructure Deployment in Australia
Sep 2019
Publication
With downward trends in Australian equipment manufacturing there are increased numbers of overseas designed manufactured and certified hydrogen systems being introduced into Australia. In parallel there are also opportunities for hydrogen and its carriers to be exported to overseas. Certainty of reputable codes and standards is important to meet regulatory requirements and community safety expectations locally and overseas.
This paper is a progress report of Hydrogen Mobility Australia’s (HMA) Technical Committee on mapping the regulatory codes and standards (RCS) gaps in Australia and establishing a pathway together with Standards Australia and Commonwealth and State Governments. This paper will discuss the benefits of the pathway covering the areas of:
This paper is a progress report of Hydrogen Mobility Australia’s (HMA) Technical Committee on mapping the regulatory codes and standards (RCS) gaps in Australia and establishing a pathway together with Standards Australia and Commonwealth and State Governments. This paper will discuss the benefits of the pathway covering the areas of:
- Safety – Enable Australia to implement consensual rules to minimise avoidable risks to persons and goods to an acceptable level
- Environment – Ensure protection of the environment from unacceptable damage due to the operation and effects of products processes and services linked to hydrogen
- Elimination of barriers to trade – Provide consistency between international jurisdictions enabling streamlined entry of hydrogen related equipment from overseas
- Upskilling of Australian industry participants – Gain useful learnings from countries more advanced in their progress in implementing ISO standards and hydrogen sector development
Helios- A New Method for Hydrogen Permeation Test
Sep 2013
Publication
Hydrogen induced cracking is still a severe and current threat for several industrial applications. With the aim of providing a simple and versatile device for hydrogen detection a new instrument was designed based on solid state sensor technology. New detection technique allows to execute hydrogen permeation measurement in short time and without material surface preparation. Thanks to this innovation HELIOS offers a concrete alternative to traditional experimental methods for laboratory permeability tests. In addition it is proposed as a new system for Non Destructive Testing of components in service in hydrogenating environment. Hydrogen flux monitoring is particularly relevant for risk mitigation of elements involved in hydrogen storage and transportation. Hydrogen permeation tests were performed by means of HELIOS instruments both on a plane membrane and on the wall of a gas cylinder. Results confirmed the extreme sensitivity of the detection system and its suitability to perform measurements even on non metallic materials by means of an easy-to-handle instrument.
Hydrogen Embrittlement Behavior of 18Ni 300 Maraging Steel Produced by Selective Laser Melting
Jul 2019
Publication
A study was performed to investigate the hydrogen embrittlement behavior of 18-Ni 300 maraging steel produced by selective laser melting and subjected to different heat treatment strategies. Hydrogen was pre-charged into the tensile samples by an electro-chemical method at the constant current density of 1 A m−2 and 50 A m−2 for 48 h at room temperature. Charged and uncharged specimens were subjected to tensile tests and the hydrogen concentration was eventually analysed using quadrupole mass spectroscopy. After tensile tests uncharged maraging samples showed fracture surfaces with dimples. Conversely in H-charged alloys quasi-cleavage mode fractures occurred. A lower concentration of trapped hydrogen atoms and higher elongation at fracture were measured in the H-charged samples that were subjected to solution treatment prior to hydrogen charging compared to the as-built counterparts. Isothermal aging treatment performed at 460 °C for 8 h before hydrogen charging increased the concentration of trapped hydrogen giving rise to higher hydrogen embrittlement susceptibility.
National Hydrogen Roadmap for Finland
Nov 2020
Publication
Hydrogen has been used as an industrial chemical for more than 100 years. Today hydrogen is used to manufacture ammonia and hence fertilizers as well as methanol and hydrogen peroxide both vital feedstocks for a wide variety of different chemical products. Furthermore in oil refineries hydrogen is used for the processing of intermediate products as well as to increase the hydrogen contents of the final products that are used propel the vehicles. However hydrogen has recently achieved new attention for its capabilities in reducing carbon emissions to the atmosphere. Producing hydrogen via low or totally carbon-free ways and using this “good” low-carbon hydrogen to replace hydrogen with a larger carbon footprint we can reduce carbon emissions. Furthermore using renewable electricity and captured carbon we can synthesise many such chemical products that are currently produced from fossil raw materials. This “Power-to-X” (P2X) is often seen as the eventual incarnation of the hydrogen economy. In addition the progress in technology both in hydrogen fuel cells and in polymer electrolyte electrolysers alike has increased their efficiencies.<br/>Furthermore production costs of renewable electricity by wind or solar power have lowered significantly. Thus cost of “good” hydrogen has also decreased markedly and production volumes are expected to increase rapidly. For these reasons many countries have raised interests in “good” hydrogen and have created roadmaps and strategies for their involvement in hydrogen. Hydrogen plays a key role also in combating climate change and reaching Finland's national goal of carbon neutrality by 2035. In recent years many clean hydrogen and P2X production methods have developed significantly and become commercially viable.<br/>This report was produced by a team of VTT experts on hydrogen and hydrogen-related technologies. The focus is in an outlook for low-carbon H2 production H2 utilization for green chemicals and fuels as well as storage transport and end-use especially during the next 10 years in Finland in connection to renewed EU regulations. This roadmap is expected to serve as the knowledge-base for further work such as shaping the hydrogen policy for Finland and determining the role of hydrogen in the national energy and climate policy.
A Study on the Continuous Spill with Limited Period of Release
Sep 2013
Publication
In this study the spread of cryogenic liquid due to a limited period of release is investigated for the first time to clarify the unclear conventional concept regarding two release types continuous and instantaneous release. In describing instantaneous release a discharge time has been assumed to be infinitesimally small; however such an assumption is unreal because there exists a finite period of release no matter how rapid it is. If the discharge time is less than the entire time domain the instantaneous release model should be added to the continuous model from the end of the time. This combined release that consists of the initial continuous model and subsequent instantaneous model is more realistic than the instantaneous release. The physical phenomenon is governed by three parameters: the evaporation rate per unit area release time and spill quantity. Third-order perturbation solutions are obtained and compared with a numerical solution to verify the perturbation solution. For the same spill quantity the combined model that consists of continuous and subsequent instantaneous model is necessary for small release times whereas the continuous model is only required for large release times. Additionally the combined release model is necessary for a small spill quantity at a fixed release time. These two release models are clearly distinguished using the perturbation solution.
A Numerical Performance Study of a Fixed-bed Reactor for Methanol Synthesis by CO2 Hydrogenation
Mar 2021
Publication
Synthetic fuels are needed to replace their fossil counterparts for clean transport. Presently their production is still inefficient and costly. To enhance the process of methanol production from CO2 and H2 and reduce its cost a particle-resolved numerical simulation tool is presented. A global surface reaction model based on the Langmuir-Hinshelwood-Hougen-Watson kinetics is utilized. The approach is first validated against standard benchmark problems for non-reacting and reacting cases. Next the method is applied to study the performance of methanol production in a 2D fixed-bed reactor under a range of parameters. It is found that methanol yield enhances with pressure catalyst loading reactant ratio and packing density. The yield diminishes with temperature at adiabatic conditions while it shows non-monotonic change for the studied isothermal cases. Overall the staggered and the random catalyst configurations are found to outperform the in-line system.
Hydrogen Effect on the Cyclic Behavior of a Superelastic NiTi Archwire
Mar 2019
Publication
In this work we are interested in examining the strain rate effect on the mechanical behavior of Ni–Ti superelastic wires after hydrogen charging and ageing for 24 h. Specimens underwent 50 cycles of loading-unloading reaching an imposed deformation of 7.6%. During loading strain rates from 10−4 s−1 to 10−2 s−1 were achieved. With a strain rate of 10−2 s−1 the specimens were charged by hydrogen for 6 h and aged for one day showed a superelastic behavior marked by an increase in the residual deformation as a function of the number of cycles. In contrast after a few number of cycles with a strain rate of 10−4 s−1 the Ni-Ti alloy archwire specimens fractured in a brittle manner during the martensite transformation stage. The thermal desorption analysis showed that for immersed specimens the desorption peak of hydrogen appeared at 320 °C. However after annealing the charged specimens by hydrogen at 400 °C for 1 h an embrittlement took place at the last cycles for the lower strain rates of 10−4 s−1. The present study suggests that the embrittlement can be due to the development of an internal stress in the subsurface of the parent phase during hydrogen charging and due to the creation of cracks and local zones of plasticity after desorption.
Toward a Fossil Free Future with HYBRIT: Development of Iron and Steelmaking Technology in Sweden and Finland
Jul 2020
Publication
The Swedish and Finnish steel industry has a world-leading position in terms of efficient blast furnace operations with low CO2 emissions. This is a result of a successful development work carried out in the 1980s at LKAB (Luossavaara-Kiirunavaara Aktiebolag mining company) and SSAB (steel company) followed by the closing of sinter plants and transition to 100% pellet operation at all of SSAB’s five blast furnaces. However to further reduce CO2 emission in iron production a new breakthrough technology is necessary. In 2016 SSAB teamed up with LKAB and Vattenfall AB (energy company) and launched a project aimed at investigating the feasibility of a hydrogen-based sponge iron production process with fossil-free electricity as the primary energy source: HYBRIT (Hydrogen Breakthrough Ironmaking Technology). A prefeasibility study was carried out in 2017 which concluded that the proposed process route is technically feasible and economically attractive for conditions in northern Sweden/Finland. A decision was made in February 2018 to build a pilot plant and construction started in June 2018 with completion of the plant planned in summer 2020 followed by experimental campaigns the following years. Parallel with the pilot plant activities a four-year research program was launched from the autumn of 2016 involving several research institutes and universities in Sweden to build knowledge and competence in several subject areas.
Energy Innovation Needs Assessment: Carbon Capture Usage & Storage
Nov 2019
Publication
The Energy Innovation Needs Assessment (EINA) aims to identify the key innovation needs across the UK’s energy system to inform the prioritisation of public sector investment in low-carbon innovation. Using an analytical methodology developed by the Department for Business Energy & Industrial Strategy (BEIS) the EINA takes a system level approach and values innovations in a technology in terms of the system-level benefits a technology innovation provides. This whole system modelling in line with BEIS’s EINA methodology was delivered by the Energy Systems Catapult (ESC) using the Energy System Modelling Environment (ESMETM) as the primary modelling tool.
To support the overall prioritisation of innovation activity the EINA process analyses key technologies in more detail. These technologies are grouped together into sub-themes according to the primary role they fulfil in the energy system. For key technologies within a sub-theme innovations and business opportunities are identified. The main findings at the technology level are summarised in sub-theme reports. An overview report will combine the findings from each sub-theme to provide a broad system-level perspective and prioritisation.
This EINA analysis is based on a combination of desk research by a consortium of economic and engineering consultants and stakeholder engagement. The prioritisation of innovation and business opportunities presented is informed by a workshop organised for each sub-theme assembling key stakeholders from the academic community industry and government.
This report was commissioned prior to advice being received from the CCC on meeting a net zero target and reflects priorities to meet the previous 80% target in 2050. The newly legislated net zero target is not expected to change the set of innovation priorities rather it will make them all more valuable overall. Further work is required to assess detailed implications.
To support the overall prioritisation of innovation activity the EINA process analyses key technologies in more detail. These technologies are grouped together into sub-themes according to the primary role they fulfil in the energy system. For key technologies within a sub-theme innovations and business opportunities are identified. The main findings at the technology level are summarised in sub-theme reports. An overview report will combine the findings from each sub-theme to provide a broad system-level perspective and prioritisation.
This EINA analysis is based on a combination of desk research by a consortium of economic and engineering consultants and stakeholder engagement. The prioritisation of innovation and business opportunities presented is informed by a workshop organised for each sub-theme assembling key stakeholders from the academic community industry and government.
This report was commissioned prior to advice being received from the CCC on meeting a net zero target and reflects priorities to meet the previous 80% target in 2050. The newly legislated net zero target is not expected to change the set of innovation priorities rather it will make them all more valuable overall. Further work is required to assess detailed implications.
Uncertainties in Explosion Risk Assessment for a Hydrogen Refuelling Station
Sep 2011
Publication
The project “Towards a Hydrogen Refuelling Infrastructure for Vehicles” (THRIVE) aimed at the determination of conditions to stimulate the building of a sustainable infrastructure for hydrogen as a car fuel in The Netherlands. Economic scenarios were constructed for the development of such an infrastructure for the next one to four decades. The eventual horizon will require the erection of a few hundred to more than a thousand hydrogen refuelling stations (HRS) in The Netherlands. The risk acceptability policy in The Netherlands implemented in the External Safety Establishments decree requires the assessment and management of safety risks imposed on the public by car fuelling stations. In the past a risk-informed policy has been developed for the large scale introduction of liquefied petroleum gas (LPG) as a car fuel and a similar policy will also be required if hydrogen is introduced in the public domain. A risk assessment methodology dedicated to cope with accident scenarios relevant for hydrogen applications is to be developed. Within the THRIVE project a demo risk assessment was conducted for the possible implementation of an HRS within an existing station for conventional fuels. The studied station is located in an urban area occupied with housing and commercial activities. The HRS is based on delivery and on-site storage of liquid hydrogen and dispensing of high pressure gaseous hydrogen into vehicles. The main challenges in the risk assessment were in the modelling of release and dispersion of liquid hydrogen. Definition of initial conditions for computational fluid dynamics (CFD) modelling to evaluate dispersion of a cold hydrogen air mixture appears rather complex and is not always fully understood. The modelling assumptions in the initial conditions determine to a large extent the likelihood and severity of potential explosion effects. The paper shows the results of the investigation and the sensitivity to the basic assumptions in the model input.
End of Life of Fuel Cells and Hydrogen Products: From Technologies to Strategies
Feb 2019
Publication
End-of-Life (EoL) technologies and strategies are needed to support the deployment of fuel cells and hydrogen (FCH) products. This article explores current and novel EoL technologies to recover valuable materials from the stacks of proton exchange membrane fuel cells and water electrolysers alkaline water electrolysers and solid oxide fuel cells. Current EoL technologies are mainly based on hydrometallurgical and pyro-hydrometallurgical methods for the recovery of noble metals while novel methods attempt to recover additional materials through efficient safe and cost-competitive pathways. Strengths weaknesses opportunities and threats of the reviewed EoL technologies are identified under techno-economic environmental and regulatory aspects. Beyond technologies strategies for the EoL of FCH stacks are defined mainly based on the role of manufacturers and recovery centres in the short- mid- and long-term. In this regard a dual role manufacturer/recovery centre would characterise long-term scenarios within a potential context of a well-established hydrogen economy.
Hydrogen Production by Electrochemical Reaction Using Ethylene Glycol with Terephthalic Acid
Jan 2021
Publication
In this study ethylene glycol (EG) and terephthalic acid (TPA) were used to generate hydrogen using copper electrodes in an alkaline aqueous solution and the corresponding reaction mechanism was experimentally investigated. Both EG and TPA produced hydrogen; however TPA consumed OH− inhibiting the production of intermediary compounds of EG and causing EG to actively react with H2O ultimately leading to enhanced hydrogen production. In addition the initiation potential of water decomposition of the EG and TPA alkaline aqueous solution was 1.0 V; when 1.8 V (vs. RHE) was applied the hydrogen production reached 440 mmol L−1 which was substantially greater than the hydrogen production rate of 150 mmol L−1 during water decomposition.
Updated Jet Flame Radiation Modelling with Corrections for Buoyancy and Wind
Sep 2013
Publication
Radiative heat fluxes from small to medium-scale hydrogen jet flames (<10 m) compare favorably to theoretical predictions provided the product species thermal emittance and optical flame thickness are corrected for. However recent heat flux measurements from two large-scale horizontally orientated hydrogen flames (17.4 and 45.9 m respectively) revealed that current methods underpredicted the flame radiant fraction by 40% or more. Newly developed weighted source flame radiation models have demonstrated substantial improvement in the heat flux predictions particularly in the near-field and allow for a sensible way to correct potential ground surface reflective irradiance. These updated methods are still constrained by the fact that the flame is assumed to have a linear trajectory despite buoyancy effects that can result in significant flame deformation. The current paper discusses a method to predict flame centerline trajectories via a one-dimensional flame integral model which enables optimized placement of source emitters for weighted multi-source heat flux prediction methods. Flame shape prediction from choked releases was evaluated against flame envelope imaging and found to depend heavily on the notional nozzle model formulation used to compute the density weighted effective nozzle diameter. Nonetheless substantial improvement in the prediction of downstream radiative heat flux values occurred when emitter placement was corrected by the flame integral model regardless of the notional nozzle model formulation used.
Consequence Models for Vented Hydrogen Deflagrations: CFD vs. Engineering Models
Sep 2017
Publication
This paper compares two approaches for predicting the consequences of vented hydrogen deflagrations: empirical engineering models (EMs) and computational fluid dynamics (CFD) simulations. The study is part of the project ‘Improving hydrogen safety for energy applications through pre-normative research on vented deflagrations’ (HySEA) funded by the Fuel Cells and Hydrogen 2 Joint Undertaking (FCH JU) under grant agreement No 671461. The HySEA project focuses on vented hydrogen deflagrations in containers and smaller enclosures with internal congestion representative of industrial applications. Data from experiments conducted as part of the HySEA project are used to evaluate predictions from a selection of EMs and the CFD tool FLACS. The experiments involve various obstacle and venting configurations and initially quiescent homogeneous hydrogen-air mixtures with hydrogen concentrations in the range 15–24 vol%. There is a significant scatter in the maximum reduced overpressures predicted by the different EMs in the present study. For certain configurations there is an order of magnitude difference between the different EM predictions. Two versions of the CFD tool FLACS are used in the present study: i) the standard commercial release FLACS v10.7r2 and ii) an in-house development version termed FLACS-beta. The commercial release generally over-predicts the maximum overpressures measured in the experiments while the development version of FLACS gives improved results for several configurations.
Implementing Maritime Battery-electric and Hydrogen Solutions: A Technological Innovation Systems Analysis
Sep 2020
Publication
Maritime transport faces increasing pressure to reduce its greenhouse gas emissions to be in accordance with the Paris Agreement. For this to happen low- and zero-carbon energy solutions need to be developed. In this paper we draw on sustainability transition literature and introduce the technological innovation system (TIS) framework to the field of maritime transportation research. The TIS approach analytically distinguishes between different innovation system functions that are important for new technologies to develop and diffuse beyond an early phase of experimentation. This provides a basis for technology-specific policy recommendations. We apply the TIS framework to the case of battery-electric and hydrogen energy solutions for coastal maritime transport in Norway. Whereas both battery-electric and hydrogen solutions have developed rapidly the former is more mature and has a strong momentum. Public procurement and other policy instruments have been crucial for developments to date and will be important for these technologies to become viable options for shipping more generally.
Tests of the Vehicle’s Powertrain with Hydrogen Fuel Cells at a Low Temperature
Sep 2019
Publication
The article discusses issues related to the operation of fuel cells stack fed with hydrogen at low temperature. The test object was a Toyota Mirai passenger car equipped with this type of powertrain. Tests were carried out in a thermoclimatic chamber at the Cracow University of Technology. They had an initial character and their aim was to evaluate the work of individual subassemblies of the propulsion system including the hydrogen supply system in terms of operational safety.
Optimal Operations for Hydrogen-based Energy Storage Systems in Wind Farms via Model Predictive Control
Feb 2021
Publication
Efficient energy production and consumption are fundamental points for reducing carbon emissions that influence climate change. Alternative resources such as renewable energy sources (RESs) used in electricity grids could reduce the environmental impact. Since RESs are inherently unreliable during the last decades the scientific community addressed research efforts to their integration with the main grid by means of properly designed energy storage systems (ESSs). In order to highlight the best performance from these hybrid systems proper design and operations are essential. The purpose of this paper is to present a so-called model predictive controller (MPC) for the optimal operations of grid-connected wind farms with hydrogen-based ESSs and local loads. Such MPC has been designed to take into account the operating and economical costs of the ESS the local load demand and the participation to the electricity market and further it enforces the fulfillment of the physical and the system's dynamics constraints. The dynamics of the hydrogen-based ESS have been modeled by means of the mixed-logic dynamic (MLD) framework in order to capture different behaviors according to the possible operating modes. The purpose is to provide a controller able to cope both with all the main physical and operating constraints of a hydrogen-based storage system including the switching among different modes such as ON OFF STAND-BY and at the same time reduce the management costs and increase the equipment lifesaving. The case study for this paper is a plant under development in the north Norway. Numerical analysis on the related plant data shows the effectiveness of the proposed strategy which manages the plant and commits the equipment so as to preserve the given constraints and save them from unnecessary commutation cycles.
The Influence of Degradation Effects in Proton Exchange Membrane Fuel Cells on Life Cycle Assessment Modelling and Environmental Impact Indicators
Apr 2022
Publication
Although proton exchange membrane fuel cell (PEMFC) systems are expected to have lower environmental impacts in the operational phase compared to conventional energy conversion systems there are still certain economic operational and environmental setbacks. Durability under a wide range of operating conditions presents a challenge because degradation processes affect the PEMFC efficiency. Typically life cycle assessment (LCA) of PEMFC systems do not include performance degradation. Thus a novel semi-empirical PEMFC model is developed which includes degradation effects caused by different operational regimes (dynamic and steady-state). The model is integrated into LCA through life cycle inventory (LCI) to achieve a more realistic and accurate evaluation of environmental impacts. Verification of the model clearly showed that the use of existing LCI models underestimates the environmental impacts. This is especially evident when green hydrogen is used in PEMFC operational phase where manufacturing phase and maintenance (stack replacements) become more influential. Input parameters of the model can be modified to reflect technological improvements (e.g. platinum loading or durability) and evaluate the effects of future scenarios.
The Impact of Disruptive Powertrain Technologies on Energy Consumption and Carbon Dioxide Emissions from Heavy-duty Vehicles
Jan 2020
Publication
Minimising tailpipe emissions and the decarbonisation of transport in a cost effective way remains a major objective for policymakers and vehicle manufacturers. Current trends are rapidly evolving but appear to be moving towards solutions in which vehicles which are increasingly electrified. As a result we will see a greater linkage between the wider energy system and the transportation sector resulting in a more complex and mutual dependency. At the same time major investments into technological innovation across both sectors are yielding rapid advancements into on-board energy storage and more compact/lightweight on-board electricity generators. In the absence of sufficient technical data on such technology holistic evaluations of the future transportation sector and its energy sources have not considered the impact of a new generation of innovation in propulsion technologies. In this paper the potential impact of a number of novel powertrain technologies are evaluated and presented. The analysis considers heavy duty vehicles with conventional reciprocating engines powered by diesel and hydrogen hybrid and battery electric vehicles and vehicles powered by hydrogen fuel cells and freepiston engine generators (FPEGs). The benefits are compared for each technology to meet the expectations of representative medium and heavy-duty vehicle drivers. Analysis is presented in terms of vehicle type vehicle duty cycle fuel economy greenhouse gas (GHG) emissions impact on the vehicle etc.. The work shows that the underpinning energy vector and its primary energy source are the most significant factor for reducing primary energy consumption and net CO2 emissions. Indeed while an HGV with a BEV powertrain offers no direct tailpipe emissions it produces significantly worse lifecycle CO2 emissions than a conventional diesel powertrain. Even with a de-carbonised electricity system (100 g CO2/kWh) CO2 emissions are similar to a conventional Diesel fuelled HGV. For the HGV sector range is key to operator acceptability of new powertrain technologies. This analysis has shown that cumulative benefits of improved electrical powertrains on-board storage efficiency improvements and vehicle design in 2025 and 2035 mean that hydrogen and electric fuelled vehicles can be competitive on gravimetric and volumetric density. Overall the work demonstrates that presently there is no common powertrain solution appropriate for all vehicle types but how subtle improvements at a vehicle component level can have significant impact on the design choices for the wider energy system.
Influence of Microstructural Morphology on Hydrogen Embrittlement in a Medium-Mn Steel Fe-12Mn-3Al-0.05C
Aug 2019
Publication
The ultrafine-grained (UFG) duplex microstructure of medium-Mn steel consists of a considerable amount of austenite and ferrite/martensite achieving an extraordinary balance of mechanical properties and alloying cost. In the present work two heat treatment routes were performed on a cold-rolled medium-Mn steel Fe-12Mn-3Al-0.05C (wt.%) to achieve comparable mechanical properties with different microstructural morphologies. One heat treatment was merely austenite-reverted-transformation (ART) annealing and the other one was a successive combination of austenitization (AUS) and ART annealing. The distinct responses to hydrogen ingression were characterized and discussed. The UFG martensite colonies produced by the AUS + ART process were found to be detrimental to ductility regardless of the amount of hydrogen which is likely attributed to the reduced lattice bonding strength according to the H-enhanced decohesion (HEDE) mechanism. With an increase in the hydrogen amount the mixed microstructure (granular + lamellar) in the ART specimen revealed a clear embrittlement transition with the possible contribution of HEDE and H-enhanced localized plasticity (HELP) mechanisms.
Development of a Realistic Hydrogen Flammable Atmosphere Inside a 4-m3 Enclosure
Sep 2017
Publication
To define a strategy of mitigation for containerized hydrogen systems (fuel cells for example) against explosion the main characteristics of flammable atmosphere (size concentration turbulence…) shall be well-known. This article presents an experimental study on accidental hydrogen releases and dispersion into an enclosure of 4 m3 (2 m x 2 m x 1 m). Different release points are studied: two circular releases of 1 and 3 mm and a system to create ring-shaped releases. The releases are operated with a pressure between 10 and 40 bars in order to be close to the process conditions. Different positions of the release inside the enclosure i.e. centred on the floor or along a wall are also studied. A specific effort is made to characterize the turbulence in the enclosure during the releases. The objectives of the experimental study are to understand and quantify the mechanisms of formation of the explosive atmosphere taking into account the geometry and position of the release point and the confinement. Those experimental data are analyzed and compared with existing models and could bring some new elements to improve them.
Removing the Disrupting Wind Effect in Single Vented Enclosure Exposed to External Wind
Oct 2015
Publication
We are addressing hydrogen release into a single-vented facility with wind blowing onto the opposite side of the vent wall. Earlier work based on tests performed by HSL with wind (within the HyIndoor project) and comparative CFD simulations with and without wind ([1]within the H2FC project) has shown that the hydrogen concentrations inside the enclosure are increased compared to the case with no wind. This was attributed to the fact that wind is disrupting the passive ventilation. The present work is based on the GAMELAN tests (within the HyIndoor project) performed with one vent and no wind. For this enclosure simulations were performed with and without wind and reproduced the disrupting wind effect. In order to remove this effect and enhance the ventilation additional simulations were performed by considering different geometrical modifications near the vent. A simple geometrical layout around the vent is here proposed that leads to elimination of the disrupting wind effect. The analysis has been performed using the ADREA-HF code earlier validated both for the HSL and the GAMELAN tests. The current work was performed partly within HyIndoor project
Fuel Cells and Hydrogen: Joint Undertaking Programme Review 2016 Final Report
Jun 2017
Publication
The Fuel Cell and Hydrogen 2 Joint Undertaking (FCH 2 JU) organised the sixth edition of its Programme Review Days (PRD). 100 projects allocated in 6 panels covering cross-cutting energy and transport in research and demonstration activities have been the basis of the FCH JU's annual review of its research and innovation programme.
Sample Scale Testing Method to Prevent Collapse of Plastic Liners in Composite Pressure Vessels
Sep 2017
Publication
Type IV pressure vessels are commonly used for hydrogen on-board stationary or bulk storages. When pressurised hydrogen permeates through the materials and solves into them. Emptying then leads to a difference of pressure at the interface between composite and liner possibly leading to a permanent deformation of the plastic liner called “collapse” or “buckling”. This phenomenon has been studied through French funded project Colline allowing to better understand its initiation and long-term effects. This paper presents the methodology followed using permeation tests hydrogen decompression tests on samples and gas diffusion calculation in order to determine safe operating conditions such as maximum flow rate or residual pressure level.
The Role of the Substrate on the Mechanical and Thermal Stability of Pd Thin Films During Hydrogen (De)sorption
Nov 2020
Publication
In this work we studied the mechanical and thermal stability of ~100 nm Pd thin films magnetron sputter deposited on a bare oxidized Si(100) wafer a sputtered Titanium (Ti) intermediate layer and a spin-coated Polyimide (PI) intermediate layer. The dependence of the film stability on the film morphology and the film-substrate interaction was investigated. It was shown that a columnar morphology with elongated voids at part of the grain boundaries is resistant to embrittlement induced by the hydride formation (α↔β phase transitions). For compact film morphology depending on the rigidity of the intermediate layer and the adherence to the substrate complete transformation (Pd-PI-SiO2/Si) or partly suppression (Pd-Ti-SiO2/Si) of the α to β-phase was observed. In the case of Pd without intermediate layer (Pd-SiO2/Si) buckling delamination occurred. The damage and deformation mechanisms could be understood by the analysis of the stresses and dislocation (defects) behavior near grain boundaries and the film-substrate interface. From diffraction line-broadening combined with microscopy analysis we showed that in Pd thin films stresses relax at critical stress values via different relaxation pathways depending on film-microstructure and film-substrate interaction. On the basis of the in-situ hydriding experiments it was concluded that a Pd film on a flexible PI intermediate layer exhibits free-standing film-like behavior besides being strongly clamped on a stiff SiO2/Si substrate.
Scottish Offshore Wind to Green Hydrogen Opportunity Assessment
Dec 2020
Publication
Initial assessment of Scotland’s opportunity to produce green hydrogen from offshore wind
Summary of Key Findings
Summary of Key Findings
- Scotland has an abundant offshore wind resource that has the potential to be a vital component in our net zero transition. If used to produce green hydrogen offshore wind can help abate the emissions of historically challenging sectors such as heating transport and industry.
- The production of green hydrogen from offshore wind can help overcome Scotland’s grid constraints and unlock a massive clean power generation resource creating a clean fuel for Scottish industry and households and a highly valuable commodity to supply rapidly growing UK and European markets.
- The primary export markets for Scottish green hydrogen are expected to be in Northern Europe (Germany Netherlands & Belgium). Strong competition to supply these markets is expected to come from green hydrogen produced from solar energy in Southern Europe and North Africa.
- Falling wind and electrolyser costs will enable green hydrogen production to be cost-competitive in the key transport and heat sectors by 2032. Strategic investment in hydrogen transportation and storage is essential to unlocking the economic opportunity for Scotland.
- Xodus’ analysis supports a long-term outlook of LCoH falling towards £2/kg with an estimated reference cost of £2.3 /kg in 2032 for hydrogen delivered to shore.
- Scotland has extensive port and pipeline infrastructure that can be repurposed for hydrogen export to the rest of UK and to Europe. Pipelines from the ‘90s are optimal for this purpose as they are likely to retain acceptable mechanical integrity and have a metallurgy better suited to hydrogen service. A more detailed assessment of export options should be performed to provide a firm foundation for early commercial green hydrogen projects.
- There is considerable hydrogen supply chain overlap with elements of parallel sectors most notably the oil and gas offshore wind and subsea engineering sectors. Scotland already has a mature hydrocarbon supply chain which is engaged in supporting green hydrogen. However a steady pipeline of early projects supported by a clear financeable route to market will be needed to secure this supply chain capability through to widescale commercial deployment.
- There are gaps in the Scottish supply chain in the areas of design manufacture and maintenance of hydrogen production storage and transportation systems. Support including apprenticeships will be needed to develop indigenous skills and capabilities in these areas.
- The development of green hydrogen from offshore wind has the potential to create high value jobs a significant proportion which are likely to be in remote rural/coastal communities located close to offshore wind resources. These can serve as an avenue for workers to redeploy and develop skills learned from oil and gas in line with Just Transition principles.
Influence of Thermal Treatment on SCC and HE Susceptibility of Supermartensitic Stainless Steel 16Cr5NiMo
Apr 2020
Publication
A 16Cr5NiMo supermartensitic stainless steel was subjected to different tempering treatments and analyzed by means of permeation tests and slow strain rate tests to investigate the effect of different amounts of retained austenite on its hydrogen embrittlement susceptibility. The 16Cr5NiMo steel class is characterized by a very low carbon content. It is the new variant of 13Cr4Ni. These steels are used in many applications for example compressors for sour environments offshore piping naval propellers aircraft components and subsea applications. The typical microstructure is a soft-tempered martensite very close to a body-centered cubic with a retained austenite fraction and limited δ ferrite phase. Supermartensitic stainless steels have high mechanical properties together with good weldability and corrosion resistance. The amount of retained austenite is useful to increase low temperature toughness and stress corrosion cracking resistance. Experimental techniques allowed us to evaluate diffusion coefficients and the mechanical behaviour of metals in stress corrosion cracking (SCC) conditions.
Urban Buses: Alternative Powertrains for Europe: A Fact-based Analysis of the Role of Diesel Hybrid, Hydrogen Fuel Cell, Trolley and Battery Electric Powertrains
Dec 2012
Publication
A coalition of 40 industrial companies and government organizations financially supported by the FCH JU elaborated a technology neutral and fact-based comparative study on eight different powertrain technologies for urban buses in Europe from 2012 to 2030.<br/>According to the results of the study only fully electric powertrain buses (based on hydrogen batteries or trolley system) have the potential to achieve zero local emissions by drastically reducing well-to-wheel emissions.<br/>Following the positive comparative result for fuel cell hydrogen urban buses the FCH JU will launch a follow-up study that more specifically defines real uptake scenarios for market entry scheduled to starting before summer 2013.
Effect of Hot Mill Scale on Hydrogen Embrittlement of High Strength Steels for Pre-Stressed Concrete Structures
Mar 2018
Publication
The presence of a conductive layers of hot-formed oxide on the surface of bars for pre or post-compressing structures can promote localized attacks as a function of pH. The aggressive local environment in the occluded cells inside localized attacks has as consequence the possibility of initiation of stress corrosion cracking. In this paper the stress corrosion cracking behavior of high strength steels proposed for tendons was studied by means of Constant Load (CL) tests and Slow Strain Rate (SSR) tests. Critical ranges of pH for cracking were verified. The promoting role of localized attack was confirmed. Further electrochemical tests were performed on bars in as received surface conditions in order to evaluate pitting initiation. The adverse effect of mill scale was recognized.
Plasmonic Nickel Nanoparticles Decorated on to LaFeO3 Photocathode for Enhanced Solar Hydrogen Generation
Nov 2018
Publication
Plasmonic Ni nanoparticles were incorporated into LaFeO3 photocathode (LFO-Ni) to excite the surface plasmon resonances (SPR) for enhanced light harvesting for enhancing the photoelectrochemical (PEC) hydrogen evolution reaction. The nanostructured LFO photocathode was prepared by spray pyrolysis method and Ni nanoparticles were incorporated on to the photocathode by spin coating technique. The LFO-Ni photocathode demonstrated strong optical absorption and higher current density where the untreated LFO film exhibited a maximum photocurrent of 0.036 mA/cm2 at 0.6 V vs RHE and when incorporating 2.84 mmol Ni nanoparticles the photocurrent density reached a maximum of 0.066 mA/cm2 at 0.6 V vs RHE due to the SPR effect. This subsequently led to enhanced hydrogen production where more than double (2.64 times) the amount of hydrogen was generated compared to the untreated LFO photocathode. Ni nanoparticles were modelled using Finite Difference Time Domain (FDTD) analysis and the results showed optimal particle size in the range of 70–100 nm for Surface Plasmon Resonance (SPR) enhancement.
The Effect of Hydrogen on the Nanoindentation Behavior of Heat Treated 718 Alloy
Oct 2020
Publication
In this study the effect of precipitates on the surface mechanical properties in the presence of hydrogen (H) is investigated by in situ electrochemical nanoindentation. The nickel superalloy 718 is subjected to three different heat treatments leading to different sizes of the precipitates: (i) solution annealing (SA) to eliminate all precipitates (ii) the as-received (AR) sample with fine dispersed precipitates and (iii) the over-aged (OA) specimen with coarser precipitates. The nanoindentation is performed using a conical tip and a new method of reverse imaging is employed to calculate the nano-hardness. The results show that the hardness of the SA sample is significantly affected by H diffusion. However it could be recovered by removing the H from its matrix by applying an anodic potential. Since the precipitates in the OA and AR samples are different they are influenced by H differently. The hardness increase for the OA sample is more significant in −1200mV while for the AR specimen the H is more effective in −1500mV. In addition the pop-in load is reduced when the samples are exposed to cathodic charging and it cannot be fully recovered by switching to an anodic potential.
Progress in Catalytic Hydrogen Production from Formic Acid over Supported Metal Complexes
Mar 2021
Publication
Formic acid is a liquid organic hydrogen carrier giving hydrogen on demand using catalysts. Metal complexes are known to be used as efficient catalysts for the hydrogen production from formic acid decomposition. Their performance could be better than those of supported catalysts with metal nanoparticles. However difficulties to separate metal complexes from the reaction mixture limit their industrial applications. This problem can be resolved by supporting metal complexes on the surface of different supports which may additionally provide some surface sites for the formic acid activation. The review analyzes the literature on the application of supported metal complexes in the hydrogen production from formic acid. It shows that the catalytic activity of some stable Ru and Ir supported metal complexes may exceed the activity of homogeneous metal complexes used for deposition. Non-noble metal-based complexes containing Fe demonstrated sufficiently high performance in the reaction; however they can be poisoned by water present in formic acid. The proposed review could be useful for development of novel catalysts for the hydrogen production.
Investigation of Mechanical Tests for Hydrogen Embrittlement in Automotive PHS Steels
Aug 2019
Publication
The problem of hydrogen embrittlement in ultra-high-strength steels is well known. In this study slow strain rate four-point bending and permeation tests were performed with the aim of characterizing innovative materials with an ultimate tensile strength higher than 1000 MPa. Hydrogen uptake in the case of automotive components can take place in many phases of the manufacturing process: during hot stamping due to the presence of moisture in the furnace atmosphere high-temperature dissociation giving rise to atomic hydrogen or also during electrochemical treatments such as cataphoresis. Moreover possible corrosive phenomena could be a source of hydrogen during an automobile’s life. This series of tests was performed here in order to characterize two press-hardened steels (PHS)—USIBOR 1500® and USIBOR 2000®—to establish a correlation between ultimate mechanical properties and critical hydrogen concentration.
Research of Nanomaterials as Electrodes for Electrochemical Energy Storage
Jan 2022
Publication
This paper has experimentally proved that hydrogen accumulates in large quantities in metal-ceramic and pocket electrodes of alkaline batteries during their operation. Hydrogen accumulates in the electrodes in an atomic form. After the release of hydrogen from the electrodes a powerful exothermic reaction of atomic hydrogen recombination with a large energy release occurs. This exothermic reaction is the cause of thermal runaway in alkaline batteries. For the KSL-15 battery the gravimetric capacity of sintered nickel matrix of the oxide-nickel electrode as hydrogen storage is 20.2 wt% and cadmium electrode is 11.5 wt%. The stored energy density in the metal-ceramic matrix of the oxide-nickel electrode of the battery KSL-15 is 44 kJ/g and in the cadmium electrode it is 25 kJ/g. The similar values for the KPL-14 battery are as follows. The gravimetric capacity of the active substance of the pocket oxide-nickel electrode as a hydrogen storage is 22 wt% and the cadmium electrode is 16.9 wt%. The density of the stored energy in the active substance oxide-nickel electrode is 48 kJ/g and in the active substance of the cadmium electrode it is 36.8 kJ/g. The obtained results of the accumulation of hydrogen energy in the electrodes by the electrochemical method are three times higher than any previously obtained results using the traditional thermochemical method.
Measuring Accuracy and Computational Capacity Trade-offs in an Hourly Integrated Energy System Model
Feb 2021
Publication
Improving energy system modelling capabilities can directly affect the quality of applied studies. However some modelling trade-offs are necessary as the computational capacity and data availability are constrained. In this paper we demonstrate modelling trade-offs resulting from the modification in the resolution of four modelling capabilities namely transitional scope European electricity interconnection hourly demand-side flexibility description and infrastructure representation. We measure the cost of increasing resolution in each capability in terms of computational time and several energy system modelling indicators notably system costs emission prices and electricity import and export levels. The analyses are performed in a national-level integrated energy system model with a linear programming approach that includes the hourly electricity dispatch with European nodes. We determined that reducing the transitional scope from seven to two periods can reduce the computational time by 75% while underestimating the objective function by only 4.6%. Modelers can assume a single European Union node that dispatches electricity at an aggregated level which underestimates the objective function by 1% while halving the computational time. Furthermore the absence of shedding and storage flexibility options can increase the curtailed electricity by 25% and 8% respectively. Although neglecting flexibility options can drastically decrease the computational time it can increase the sub-optimality by 31%. We conclude that an increased resolution in modelling flexibility options can significantly improve the results. While reducing the computational time by half the lack of electricity and gas infrastructure representation can underestimate the objective function by 4% and 6% respectively.
In Situ X-ray Absorption Spectroscopy Study on Water Formation Reaction of Palladium Metal Nanoparticle Catalysts
Oct 2015
Publication
Proper management of hydrogen gas is very important for safety security of nuclear power plants. Hydrogen removal by water formation reaction on a catalyst is one of the candidates for creating hydrogen free system. We observed in situ and time-resolved structure change of palladium metal nanoparticle catalyst during the water formation reaction by using X-ray absorption spectroscopy technique. A poisoning effect by carbon monoxide on catalytic activity was also studied. We have found that the creation of oxidized surface layer on palladium metal nanoparticles plays an important role for the water formation reaction process.
Linking Ab Initio Data on Hydrogen and Carbon in Steel to Statistical and Continuum Descriptions
Mar 2018
Publication
We present a selection of scale transfer approaches from the electronic to the continuum regime for topics relevant to hydrogen embrittlement. With a focus on grain boundary related hydrogen embrittlement we discuss the scale transfer for the dependence of the carbon solution behavior in steel on elastic effects and the hydrogen solution in austenitic bulk regions depending on Al content. We introduce an approximative scheme to estimate grain boundary energies for varying carbon and hydrogen population. We employ this approach for a discussion of the suppressing influence of Al on the substitution of carbon with hydrogen at grain boundaries which is an assumed mechanism for grain boundary hydrogen embrittlement. Finally we discuss the dependence of hydride formation on the grain boundary stiffness
Combustion and Exhaust Emission Characteristics, and In-cylinder Gas Composition, of Hydrogen Enriched Biogas Mixtures in a Diesel Engine
Feb 2017
Publication
This paper presents a study undertaken on a naturally aspirated direct injection diesel engine investigating the combustion and emission characteristics of CH4-CO2 and CH4-CO2 -H2 mixtures. These aspirated gas mixtures were pilot-ignited by diesel fuel while the engine load was varied between 0 and 7 bar IMEP by only adjusting the flow rate of the aspirated mixtures. The in-cylinder gas composition was also investigated when combusting CH4-CO2 and CH4-CO2-H2 mixtures at different engine loads with in cylinder samples collected using two different sampling arrangements. The results showed a longer ignition delay period and lower peak heat release rates when the proportion of CO2 was increased in the aspirated mixture. Exhaust CO2 emissions were observed to be higher for 60 CH4:40CO2 mixture but lower for the 80CH4:20CO2 mixture as compared to diesel fuel only combustion at all engine loads. Both exhaust and in-cylinder NOx levels were observed to decrease when the proportion of CO2 was increased; NOx levels increased when the proportion of H2 was increased in the aspirated mixture. In-cylinder NOx levels were observed to be higher in the region between the sprays as compared to within the spray core attributable to higher gas temperatures reached post ignition in that region.
Hydrogen Effects in Non-ferrous Alloys: Discussion
Jun 2017
Publication
This is a transcript of the discussion session on the effects of hydrogen in the non-ferrous alloys of zirconium and titanium which are anisotropic hydride-forming metals. The four talks focus on the hydrogen embrittlement mechanisms that affect zirconium and titanium components which are respectively used in the nuclear and aerospace industries. Two specific mechanisms are delayed hydride cracking and stress corrosion cracking.
This article is a transcription of the recorded discussion of the session ‘Hydrogen in non-ferrous alloys’ at the Royal Society Discussion Meeting Challenges of Hydrogen in Metals 16–18 January 2017. The text is approved by the contributors. M.P. transcribed the session. M.A.S. assisted in the preparation of the manuscript.
Link to document download on Royal Society Website
This article is a transcription of the recorded discussion of the session ‘Hydrogen in non-ferrous alloys’ at the Royal Society Discussion Meeting Challenges of Hydrogen in Metals 16–18 January 2017. The text is approved by the contributors. M.P. transcribed the session. M.A.S. assisted in the preparation of the manuscript.
Link to document download on Royal Society Website
Zero-In on NI-Heat Exploring Pathways Towards Heat Decarbonisation in Northern Ireland
Jul 2020
Publication
Northern Ireland has achieved its 2020 targets in the electricity sector ahead of time with 46.8% of its electricity demand supplied by renewable generators. When it comes to heat the progress is less impressive – 68% of domestic heating is provided by oil and only around 2500 customers use low carbon heat generators in their homes. In addition 22% of consumers live in fuel poverty. Fuel poverty support programmes still propose the replacement of old oil boilers with new models or with gas boilers where a connection to the grid is possible.<br/>Failure of the commercial RHI scheme and the knock-on effect of the closure of the domestic RHI scheme caused significant damage to the industry and to the reputation of low carbon heat technologies leaving NI consumers without any explicit supporting mechanisms for low carbon heat supply. Decreases in carbon emissions from the heat sector are mainly achieved through switching from oil to gas heating. Gas infrastructure is under development in NI and promises to reach 60% of customers by 2022.
Annual Science Review 2018
Mar 2018
Publication
THIS ANNUAL SCIENCE Review showcases the high quality of science evidence and analysis that underpins HSE’s risk-based regulatory regime. To be an effective regulator HSE has to balance its approaches to informing directing advising and enforcing through a variety of activities. For this we need capacity to advance knowledge; to develop and use robust evidence and analysis; to challenge thinking; and to review effectiveness.<br/>In simple terms policy provides the route map to tackling issues. HSE is particularly well placed in terms of the three components of effective policy - “politics” “evidence” and “delivery”. Unlike most regulators and arms-length bodies HSE leads on policy development which draws directly on front line delivery expertise and intelligence; and we are also unusual in having our own world class science and insight capabilities.<br/>The challenge is to ensure we bring these components together to best effect to respond to new risk management and regulatory issues with effective innovative and proportionate approaches.<br/>Many of the articles in this Review relate to new and emerging technologies and the changing world of work and it is important to understand the risks these may pose and how they can be effectively controlled or how they themselves can contribute to improved health and safety in the workplace. Good policy development can support approaches to change that are proportionate relevant persuasive and effective. For example work described in these pages is: to help understand changing workplace exposures; to provide robust evidence to those negotiating alternatives to unduly prescriptive standards; to understand how best to influence duty<br/>holder behaviors in the changing world of work; to inform possible legislative changes to allow different modes of safe gas transmission; to change administrative processes for Appointed Doctors; and to support our position as a model modern regulator by further focusing our inspection activity where it matters most.<br/>The vital interface between HSE science and policy understand how best to influence duty holder behaviors in the changing world of work; to inform possible legislative changes to allow different modes of safe gas transmission; to change administrative processes for Appointed Doctors; and to support our position as a model modern regulator by further focusing our inspection activity where it matters most.<br/>We work well together and it is important we maintain this engagement as a conscious collaboration.
Oxford Energy Podcast – How a Traded Hydrogen Market Might Develop – Lessons from the Natural Gas Industry
Jun 2021
Publication
The appetite for a ‘hydrogen market’ has been growing in the past year or two and is often called a ‘market’ by governments regulators and other energy industry players. The question is what ‘hydrogen market’ are they referring to as there is currently no such market established? In this podcast David Ledesma talks to Patrick Heather Senior Research Fellow at the OIES and discusses how a future traded hydrogen market might develop what the prerequisites would be for the development of a wholesale market and whether there are lessons to be learned from the development of the European natural gas market. The podcast ends up by asking the fundamental question – If the European gas market took 25-30 years to liberalise and develop a liquid traded pricing hub where are we headed with hydrogen? Will we ever see a traded market in hydrogen and what must happen to get there? Patrick is cautiously optimistic in his response!
The podcast can be found on their website
The podcast can be found on their website
Establishing a Hydrogen Economy: The Future of Energy 2035
May 2019
Publication
The next few decades are expected to be among the most transformative the energy sector has ever seen. Arup envisages a world with a much more diverse range of heating sources and with significantly lower emissions and renewable energy powering transport.<br/>As part of this the establishment of a strong hydrogen economy is a very real opportunity and is within reaching distance. Our report uses the UK as a case study example and explores the challenges and opportunities for hydrogen in the context of the whole energy system.<br/>Read about the progress already being made in using hydrogen for transport and heat. And the need to progress policy and collaboration between government the private sector and other stakeholders to shape future demand change consumer perception and create the strong supply chains needed to allow the hydrogen economy to thrive.
High-pressure Hydrogen Production with Inherent Sequestration of a Pure Carbon Dioxide Stream Via Fixed Bed Chemical Looping
Feb 2019
Publication
The proof of concept for the production of pure pressurized hydrogen from hydrocarbons in combination with the sequestration of a pure stream of carbon dioxide with the reformer steam iron cycle is presented. The iron oxide based oxygen carrier (95% Fe2O3 5% Al2O3) is reduced with syngas and oxidized with steam at 1023 K. The carbon dioxide separation is achieved via partial reduction of the oxygen carrier from Fe2O3 to Fe3O4 yielding thermodynamically to a product gas only containing CO2 and H2O. By the subsequent condensation of steam pure CO2 is sequestrated. After each steam oxidation phase an air oxidation was applied to restore the oxygen carrier to hematite level. Product gas pressures of up to 30.1 bar and hydrogen purities exceeding 99% were achieved via steam oxidations. The main impurities in the product gas are carbon monoxide and carbon dioxide which originate from solid carbon depositions or from stored carbonaceous molecules inside the pores of the contact mass. The oxygen carrier samples were characterized using elemental analysis BET surface area measurement XRD powder diffraction SEM and light microscopy. The maximum pressure of 95 bar was demonstrated for hydrogen production in the steam oxidation phase after the full oxygen carrier reduction significantly reducing the energy demand for compressors in mobility applications.
Opportunity and Cost of Green Hydrogen in Kuwait: A Preliminary Assessment
Apr 2021
Publication
On April 7 2021 OIES with and the Kuwait Foundation for the Advancement of Sciences (KFAS) held the annual OIES-KFAS Workshop on Energy Transition Post-Pandemic in the Gulf. During the hydrogen session a paper titled “Opportunity and Cost of Green Hydrogen in Kuwait: A Preliminary Assessment” co-authored by Dr. Manal Shehabi was presented.
Like others states in the GCC Kuwait is seeking to explore hydrogen as part of its energy transition projects. The presentation highlights key technological opportunities for green hydrogen in Kuwait followed by a techno-economic assessments of producing it. Results of utilized hydrogen production model show that for production in 2032 average levelized cost of hydrogen (LCOH) is $3.23/kg using PEM technology & $4.41/kg using SOEC technology. Results indicate that green hydrogen in Kuwait is more competitive than in other regions but currently not competitive (>$1.5/kg) with oil coal and gas in absence of carbon taxes.
The research paper can be found on their website
Like others states in the GCC Kuwait is seeking to explore hydrogen as part of its energy transition projects. The presentation highlights key technological opportunities for green hydrogen in Kuwait followed by a techno-economic assessments of producing it. Results of utilized hydrogen production model show that for production in 2032 average levelized cost of hydrogen (LCOH) is $3.23/kg using PEM technology & $4.41/kg using SOEC technology. Results indicate that green hydrogen in Kuwait is more competitive than in other regions but currently not competitive (>$1.5/kg) with oil coal and gas in absence of carbon taxes.
The research paper can be found on their website
Recent Advances in Biomass Pretreatment Technologies for Biohydrogen Production
Jan 2022
Publication
Hydrogen is an economical source of clean energy that has been utilized by industry for decades. In recent years demand for hydrogen has risen significantly. Hydrogen sources include water electrolysis hydrocarbon steam reforming and fossil fuels which emit hazardous greenhouse gases and therefore have a negative impact on global warming. The increasing worldwide population has created much pressure on natural fuels with a growing gap between demand for renewable energy and its insufficient supply. As a result the environment has suffered from alarming increases in pollution levels. Biohydrogen is a sustainable energy form and a preferable substitute for fossil fuel. Anaerobic fermentation photo fermentation microbial and enzymatic photolysis or combinations of such techniques are new approaches for producing biohydrogen. For cost-effective biohydrogen production the substrate should be cheap and renewable. Substrates including algal biomass agriculture residue and wastewaters are readily available. Moreover substrates rich in starch and cellulose such as plant stalks or agricultural waste or food industry waste such as cheese whey are reported to support dark- and photo-fermentation. However their direct utilization as a substrate is not recommended due to their complex nature. Therefore they must be pretreated before use to release fermentable sugars. Various pretreatment technologies have been established and are still being developed. This article focuses on pretreatment techniques for biohydrogen production and discusses their efficiency and suitability including hybrid-treatment technology
Magnetic Field Enhancement of Electrochemical Hydrogen Evolution Reaction Probed by Magneto-optics
Nov 2020
Publication
External magnetic fields affect various electrochemical processes and can be used to enhance the efficiency of the electrochemical water splitting reaction. However the driving forces behind this effect are poorly understood due to the analytical challenges of the available interface-sensitive techniques. Here we present a set-up based on magneto- and electro-optical probing which allows to juxtapose the magnetic properties of the electrode with the electrochemical current densities in situ at various applied potentials and magnetic fields. On the example of an archetypal hydrogen evolution catalyst Pt (in a form of Co/Pt superlattice) we provide evidence that a magnetic field acts on the electrochemical double layer affecting the local concentration gradient of hydroxide ions which simultaneously affects the magneto-optical and magnetocurrent response.
Fuel Cells and Hydrogen: Joint Undertaking Programme Review 2011 Final Report
Apr 2012
Publication
The Fuel Cells and Hydrogen Joint Undertaking (FCH JU) has the ambitious objective to place Europe at the forefront of the development commercialization and deployment of fuel cells and hydrogen technologies as of 2015. About €470 million over a six year period have been granted by the European Union to achieve this and private funds are being attracted to support the same ambition as part of the global European effort embedded in the multi-annual implementation plan MAIP (2008-2013).
Hydrogen Diffusion Mechanism around a Crack Tip in Type 304L Austenite Stainless Steel Considering the Influence of the Volume Expansion of Strain-Induced Martensite Transformation
Sep 2019
Publication
Strain-induced martensite transformation (SIMT) commonly exists around a crack tip of metastable austenite stainless steels. The influence of the volume expansion of the SIMT on the hydrogen diffusion was investigated by hydrogen diffusion modelling around a crack tip in type 304L austenite stainless steel. The volume expansion changed the tensile stress state into pressure stress state at the crack tip resulting in a large stress gradient along the crack propagation direction. Compared to the analysis without considering the volume expansion effect this volume expansion further accelerated the hydrogen transport from the inner surface to a critical region ahead of the crack tip and further increased the maximum value of the hydrogen concentration at the critical position where the strain-induced martensite fraction approximates to 0.1 indicating that the volume expansion of the SIMT further increased the hydrogen embrittlement susceptibility.
Fuel Cells and Hydrogen Technologies in Europe: Financial and Technology Outlook on the European Sector Ambition 2014-2020
Nov 2011
Publication
Sustainable secure and competitive energy supply and transport services are at the heart of the EU2020 strategy towards a low carbon and inclusive economy geared towards a reduction of 80% of CO2 emissions by 2050. This objective has been endorsed by the European Institutions and Member States. It is widely recognised that a technological shift and the deployment of new clean technologies are critical for a successful transition to such a new sustainable economy. Furthermore in addition to bringing a healthier environment and securing energy supply innovation will provide huge opportunities for the European economy. However this paradigm shift will not be purely driven by the market. A strong and determined commitment of public institutions and the private sector together are necessary to support the European political ambition. The period 2014-2020 will be critical to ensure that the necessary investments are realized to support the EU2020 vision. In terms of hydrogen and fuel cell technologies significant investments are required for (a) transportation for scaling up the car fleet and building up of refuelling infrastructure needs (b) hydrogen production technologies to integrate renewable intermittent power sources to the electrical grid (wind and solar) (c) stationary fuel cell applications with large demonstration projects in several European cities and (d) identified early markets (material handling vehicles back-up power systems) to allow for volume developments and decrease of system-costs.<br/>This Report summarizes the sector’s financial ambition to reach Europe’s objectives in 2020.
A Personal Retrospect on Three Decades of High Temperature Fuel Cell Research; Ideas and Lessons Learned
Feb 2021
Publication
In 1986 the Dutch national fuel cell program started. Fuel cells were developed under the paradigm of replacing conventional technology. Coal-fired power plants were to be replaced by large-scale MCFC power plants fuelled by hydrogen in a full-scale future hydrogen economy. With today's knowledge we will reflect on these and other ideas with respect to high temperature fuel cell development including the choice for the type of high temperature fuel cell. It is explained that based on thermodynamics proton conducting fuel cells would have been a better choice and the direct carbon fuel cell even more so with electrochemical gasification of carbon as the ultimate step. The specific characteristics of fuel cells and multisource multiproduct systems were not considered whereas we understand now that these can provide huge driving forces for the implementation of fuel cells compared to just replacing conventional combined heat and power production technology.
Palladium (Pd) Membranes as Key Enabling Technology for Pre-combustion CO2 Capture and Hydrogen Production
Aug 2017
Publication
Palladium (Pd) membranes are a promising enabling technology for power generation and hydrogen production with CO2 capture. SINTEF has developed and patented a flexible technology to produce Pd-alloy membranes that significantly improves flux and thereby reduces material costs. Reinertsen AS and SINTEF aim to demonstrate the Pd membrane technology for H2 separation on a side stream of the Statoil Methanol Plant at Tjeldbergodden Norway. In the present article we present the upscaling of the membrane manufacturing process together with the membrane module and skid design and construction.
Ammonia-hydrogen Combustion in a Swirl Burner with Reduction of NOx Emissions
Sep 2019
Publication
Recently ammonia is being considered for fuelling gas turbines as a new sustainable source. It can undergo thermal cracking producing nitrogen hydrogen and unburned ammonia thus enabling the use of these chemicals most efficiently for combustion purposes. Ammonia being carbon-free may allow the transition towards a hydrogen economy. However one of the main constraints of this fuelling technique is that although the combustion of ammonia produces no CO2 there is a large NOx proportion of emissions using this fuel. In this work cracked ammonia obtained from a modified combustion rig designed at Cardiff University was used to simulate a swirl burner under preheating conditions via heat exchangers. The primary objective of this system is to find new ways for the reduction of NOx emissions by injecting various amounts of ammonia/hydrogen at different mixtures downstream of the primary flame zone. The amount of injected ammonia/hydrogen mixture (X) taken from the thermal cracking system was ranged from 0%-4% (vol %) of the total available fuel in the system while the remaining gas (1.00-X) was then employed as primary fuel into the burner. CHEMKIN- PRO calculations were conducted by employing a novel chemical reaction code developed at Cardiff University to achieve the goal of this paper. The predictions were performed under low pressure and rich conditions with an equivalence ratio ϕ =1.2 in a swirl burner previously characterised at output powers of ~10 kW. Ammonia and hydrogen blends were evaluated from 50% NH3 (vol %) with the remaining gas as hydrogen continuing in steps of 10% (vol %) NH3 increments. Results showed that the minimum unburned ammonia and higher flame temperature were achieved at 60%-40% NH3-H2 when compared to other blends but with high NO emissions. These NO levels were reduced by injecting a small amount of NH3/H2 mixture (X=4 %) downstream the primary zone in a generated circulations promoted by the new design of the burner which affecting the residence time hence reducing the NO emission in the exhaust gas.
No more items...