- Home
- A-Z Publications
- Publications
Publications
HyDeploy2: Network Information and Maps
Jun 2021
Publication
Winlaton site was chosen as the site for the HyDeploy 2 North East trial as it was seen as the site that offered a high degree of variability with regards materials on the network size of network and statistical representation of housing. The Winlaton trial network is an estate of the wider Winlaton gas network situated in Blaydon near Gateshead. The Winlaton trial network has been isolated from the wider Winlaton gas network where it was previously supplied from and will be supplied with the blended gas from NGN’s Low Thornley gas depot with the installation of a brand-new pressure regulating district governor.<br/>The data contained within this report outlines the expected seasonal gas demand on the Winlaton trial network and the associated leakage and repair history for the network. No unusual repairs or leakage behaviour has been observed on this network. A DSEAR assessment has been conducted on the governor station ensuring ATEX compliance. The network isolation and reinforcement requirements are also given in this report highlighting the necessary actions to isolate the trial network from the wider Winlaton gas network. The NGN Safety Case outlines the risks associated with the operation of a gas grid and the ALARP mitigations developed to minimise them and what response is necessary in case such risks are realised. The existing safety case will be amended to account for the infrastructural operational and commercial changes associated with the HyDeploy 2 project. The report also contains a detailed register of all the assets on the Winlaton trial network this data set was used to inform the scientific research programme and specifically to allow an assessment to be carried out with regards to the operability of the existing and newly installed assets on the Winlaton trial network with respect to the blended gas.<br/>Click on supplement tab to view the other documents from this report
Renewable Power-to-Gas: A Technological and Economic Review
Aug 2015
Publication
The Power-to-Gas (PtG) process chain could play a significant role in the future energy system. Renewable electric energy can be transformed into storable methane via electrolysis and subsequent methanation. This article compares the available electrolysis and methanation technologies with respect to the stringent requirements of the PtG chain such as low CAPEX high efficiency and high flexibility. Three water electrolysis technologies are considered: alkaline electrolysis PEM electrolysis and solid oxide electrolysis. Alkaline electrolysis is currently the cheapest technology; however in the future PEM electrolysis could be better suited for the PtG process chain. Solid oxide electrolysis could also be an option in future especially if heat sources are available. Several different reactor concepts can be used for the methanation reaction. For catalytic methanation typically fixed-bed reactors are used; however novel reactor concepts such as three-phase methanation and micro reactors are currently under development. Another approach is the biochemical conversion. The bioprocess takes place in aqueous solutions and close to ambient temperatures. Finally the whole process chain is discussed. Critical aspects of the PtG process are the availability of CO2 sources the dynamic behaviour of the individual process steps and especially the economics as well as the efficiency.
Techno-Economic Analysis of a Novel Hydrogen-Based Hybrid Renewable Energy System for Both Grid-Tied and Off-Grid Power Supply in Japan: The Case of Fukushima Prefecture
Jun 2020
Publication
After the Great East Japan Earthquake energy security and vulnerability have become critical issues facing the Japanese energy system. The integration of renewable energy sources to meet specific regional energy demand is a promising scenario to overcome these challenges. To this aim this paper proposes a novel hydrogen-based hybrid renewable energy system (HRES) in which hydrogen fuel can be produced using both the methods of solar electrolysis and supercritical water gasification (SCWG) of biomass feedstock. The produced hydrogen is considered to function as an energy storage medium by storing renewable energy until the fuel cell converts it to electricity. The proposed HRES is used to meet the electricity demand load requirements for a typical household in a selected residential area located in Shinchi-machi in Fukuoka prefecture Japan. The techno-economic assessment of deploying the proposed systems was conducted using an integrated simulation-optimization modeling framework considering two scenarios: (1) minimization of the total cost of the system in an off-grid mode and (2) maximization of the total profit obtained from using renewable electricity and selling surplus solar electricity to the grid considering the feed-in-tariff (FiT) scheme in a grid-tied mode. As indicated by the model results the proposed HRES can generate about 47.3 MWh of electricity in all scenarios which is needed to meet the external load requirement in the selected study area. The levelized cost of energy (LCOE) of the system in scenarios 1 and 2 was estimated at 55.92 JPY/kWh and 56.47 JPY/kWh respectively
Instantaneous Hydrogen Production from Ammonia by Non-thermal Arc Plasma Combining with Catalyst
Jul 2021
Publication
Owing to the storage and transportation problems of hydrogen fuel exploring new methods of the realtime hydrogen production from ammonia becomes attractive. In this paper non-thermal arc plasma (NTAP) combining with NiO/Al2O3 catalyst is developed to produce hydrogen from ammonia with high efficiency and large scale. The effects of ammonia gas flow rate and discharge power on the gas temperature electron density the hydrogen production rate and energy efficiency were investigated. Experimental results show that the optical emission spectrum of NTAP working with pure ammonia medium was dominated by the atom spectrum of Hα Hβ and molecular spectrum of NH component. Under the optimum experimental condition of plasma discharge the highest energy efficiency of hydrogen production reached 783.4 L/kW·h at NH3 gas flow rate of 30 SLM. When the catalyst was added and heated by the NTAP simultaneously the energy efficiency further increased to 1080.0 L/kW·h.
The Implications of Ambitious Decarbonisation of Heat and Road Transport for Britain’s Net Zero Carbon Energy Systems
Oct 2021
Publication
Decarbonisation of heating and road transport are regarded as necessary but very challenging steps on the pathway to net zero carbon emissions. Assessing the most efficient routes to decarbonise these sectors requires an integrated view of energy and road transport systems. Here we describe how a national gas and electricity transmission network model was extended to represent multiple local energy systems and coupled with a national energy demand and road transport model. The integrated models were applied to assess a range of technologies and policies for heating and transport where the UK’s 2050 net zero carbon emissions target is met. Overall annual primary energy use is projected to reduce by between 25% and 50% by 2050 compared to 2015 due to ambitious efficiency improvements within homes and vehicles. However both annual and peak electricity demands in 2050 are more than double compared with 2015. Managed electric vehicle charging could save 14TWh/year in gas-fired power generation at peak times and associated emissions whilst vehicle-to-grid services could provide 10GW of electricity supply during peak hours. Together managed vehicle charging and vehicle-to-grid supplies could result in a 16% reduction in total annual energy costs. The provision of fast public charging facilities could reduce peak electricity demand by 17GW and save an estimated £650 million annually. Although using hydrogen for heating and transport spreads the hydrogen network costs between homeowners and motorists it is still estimated to be more costly overall compared to an all-electric scenario. Bio-energy electricity generation plants with carbon capture and storage are required to drive overall energy system emissions to net zero utilisation of which is lowest when heating is electrified and road transport consists of a mix of electric and hydrogen fuel-cell vehicles. The analysis demonstrates the need for an integrated systems approach to energy and transport policies and for coordination between national and local governments.
Reforming Processes for Syngas Production: A Mini-review on the Current Status, Challenges, and Prospects for Biomass Conversion to Fuels
Mar 2022
Publication
Dedicated bioenergy combined with carbon capture and storage are important elements for the mitigation scenarios to limit the global temperature rise within 1.5 °C. Thus the productions of carbon-negative fuels and chemicals from biomass is a key for accelerating global decarbonisation. The conversion of biomass into syngas has a crucial role in the biomass-based decarbonisation routes. Syngas is an intermediate product for a variety of chemical syntheses to produce hydrogen methanol dimethyl ether jet fuels alkenes etc. The use of biomass-derived syngas has also been seen as promising for the productions of carbon negative metal products. This paper reviews several possible technologies for the production of syngas from biomass especially related to the technological options and challenges of reforming processes. The scope of the review includes partial oxidation (POX) autothermal reforming (ATR) catalytic partial oxidation (CPO) catalytic steam reforming (CSR) and membrane reforming (MR). Special attention is given to the progress of CSR for biomass-derived vapours as it has gained significant interest in recent years. Heat demand and efficiency together with properties of the reformer catalyst were reviewed more deeply in order to understand and propose solutions to the problems that arise by the reforming of biomass-derived vapours and that need to be addressed in order to implement the technology on a big scale.
Everything About Hydrogen Podcast: A New Hope for Hydrogen?
Apr 2020
Publication
On this weeks episode the team discuss the Hydrogen Council the global stakeholder forum that has been at the forefront of efforts to advance the role of hydrogen and fuel cell technologies globally. We are excited to have as our guests Pierre-Etienne Franc Vice President for the Hydrogen Energy World Business Unit at Air Liquide and Stephan Herbst General Manager at Toyota Motor Europe. On the show we discuss why Air Liquide and Toyota decided to engage with the Council its strategy vision and perspective on the role that hydrogen can play in the energy transition and how companies can work with policymakers to enable this process. All this and more on the show!
The podcast can be found on their website
The podcast can be found on their website
Hydrogen and Hydrogen-derived Fuels through Methane Decomposition of Natural Gas – GHG Emissions and Costs
May 2020
Publication
Hydrogen can be produced from the decomposition of methane (also called pyrolysis). Many studies assume that this process emits few greenhouse gas (GHG) because the reaction from methane to hydrogen yields only solid carbon and no CO2. This paper assesses the life-cycle GHG emissions and the levelized costs for hydrogen provision from methane decomposition in three configurations (plasma molten metal and thermal gas). The results of these configurations are then compared to electrolysis and steam methane reforming (SMR) with and without CO2capture and storage (CCS). Under the global natural gas supply chain conditions hydrogen from methane decomposition still causes significant GHG emissions between 43 and 97 g CO2-eq./MJ. The bandwidth is predominately determined by the energy source providing the process heat i.e. the lowest emissions are caused by the plasma system using renewable electricity. This configuration shows lower GHG emissions compared to the “classical” SMR (99 g CO2-eq./MJ) but similar emissions to the SMR with CCS (46 g CO2-eq./MJ). However only electrolysis powered with renewable electricity leads to very low GHG emissions (3 g CO2-eq./MJ). Overall the natural gas supply is a decisive factor in determining GHG emissions. A natural gas supply with below-global average GHG emissions can lead to lower GHG emissions of all methane decomposition configurations compared to SMR. Methane decomposition systems (1.6 to 2.2 €/kg H2) produce hydrogen at costs substantially higher compared to SMR (1.0 to 1.2 €/kg) but lower than electrolyser (2.5 to 3.0 €/kg). SMR with CCS has the lowest CO2abatement costs (24 €/t CO2-eq. other > 141 €/t CO2-eq.). Finally fuels derived from different hydrogen supply options are assessed. Substantially lower GHG emissions compared to the fossil reference (natural gas and diesel/gasoline) are only possible if hydrogen from electrolysis powered by renewable energy is used (>90% less). The other hydrogen pathways cause only slightly lower or even higher GHG emissions.
Development of Liquid Hydrogen Leak Frequencies Using a Bayesian Update Process
Sep 2021
Publication
To quantify the risk of an accident in a liquid hydrogen system it is necessary to determine how often a leak may occur. To do this representative component leakage frequencies specific to liquid hydrogen can be determined as a function of the normalized leak size. Subsequently the system characteristics (e.g. system pressure) can be used to calculate accident consequences. Operating data (such as leak frequencies) for liquid hydrogen systems are very limited; rather than selecting a single leak frequency value from a literature source data from different sources can be combined using a Bayesian model. This approach provides leakage rates for different amounts of leakage distributions for leakage rates to propagate through risk assessment models to establish risk result uncertainty and a means for incorporating liquid hydrogen-specific leakage data with leakage frequencies from other fuels. Specifically other cryogenic fluids like liquefied natural gas are used as a baseline for the Bayesian analysis. This Bayesian update process is used to develop leak frequency distributions for different system component types and leak sizes. These leak frequencies can be refined as liquid hydrogen data becomes available and may then inform safety code requirements based on the likelihood of liquid hydrogen release for different systems.
Development of Renewable Energy Multi-energy Complementary Hydrogen Energy System (A Case Study in China): A Review
Aug 2020
Publication
The hydrogen energy system based on the multi-energy complementary of renewable energy can improve the consumption of renewable energy reduce the adverse impact on the power grid system and has the characteristics of green low carbon sustainable etc. which is currently a global research hotspot. Based on the basic principles of hydrogen production technology this paper introduces the current hydrogen energy system topology and summarizes the technical advantages of renewable energy complementary hydrogen production and the complementary system energy coordination forms. The problems that have been solved or reached consensus are summarized and the current status of hydrogen energy system research at home and abroad is introduced in detail. On this basis the key technologies of multi-energy complementation of hydrogen energy system are elaborated especially in-depth research and discussion on coordinated control strategies energy storage and capacity allocation energy management and electrolysis water hydrogen production technology. The development trend of the multi-energy complementary system and the hydrogen energy industry chain is also presented which provides a reference for the development of hydrogen production technology and hydrogen energy utilization of the renewable energy complementary system.
Modelling and Experimental Analysis of a Polymer Electrolyte Membrane Water Electrolysis Cell at Different Operating Temperatures
Nov 2018
Publication
In this paper a simplified model of a Polymer Electrolyte Membrane (PEM) water electrolysis cell is presented and compared with experimental data at 60 ◦C and 80 ◦C. The model utilizes the same modelling approach used in previous work where the electrolyzer cell is divided in four subsections: cathode anode membrane and voltage. The model of the electrodes includes key electrochemical reactions and gas transport mechanism (i.e. H2 O2 and H2O) whereas the model of the membrane includes physical mechanisms such as water diffusion electro osmotic drag and hydraulic pressure. Voltage was modelled including main overpotentials (i.e. activation ohmic concentration). First and second law efficiencies were defined. Key empirical parameters depending on temperature were identified in the activation and ohmic overpotentials. The electrodes reference exchange current densities and change transfer coefficients were related to activation overpotentials whereas hydrogen ion diffusion to Ohmic overvoltages. These model parameters were empirically fitted so that polarization curve obtained by the model predicted well the voltage at different current found by the experimental results. Finally from the efficiency calculation it was shown that at low current densities the electrolyzer cell absorbs heat from the surroundings. The model is not able to describe the transients involved during the cell electrochemical reactions however these processes are assumed relatively fast. For this reason the model can be implemented in system dynamic modelling for hydrogen production and storage where components dynamic is generally slower compared to the cell electrochemical reactions dynamics.
Optical, Electrical and Structural Study of Mg/Ti Bilayer Thin Film for Hydrogen Storage Applications
Apr 2021
Publication
Bilayer Mg/Ti (200 nm) thin films were successfully prepared by using D.C. magnetron sputtering unit. These films were vacuum annealed at 573 K temperature for one hour to obtain homogeneous and intermixed structure of bilayer. Hydrogenation of these thin film structures was made at different hydrogen pressure (15 30 & 45 psi) for 30 min to visualize the effect of hydrogen on film structure. The UV–Vis absorption spectra I-V characteristics and Raman spectroscopy were carried out to study the effect of hydrogen on optical electrical and structural properties of Mg/Ti bilayer thin films. The annealed thin film represents the semiconductor nature with the conductivity of the order of 10-5 Ώ−1-m−1 and it decreases as hydrogen pressure increases. The nonlinear dependence of resistivity on hydrogen pressure reveals inhomogeneous distribution of hydrogen in the thin film. Raman spectroscopy confirmed the presence of hydrogen in thin film where the intensity of peaks was found to be decreased with hydrogen pressure.
Toward Design of Synergistically Active Carbon-Based Catalysts for Electrocatalytic Hydrogen Evolution
Apr 2014
Publication
Replacement of precious catalyst with cost-effective alternatives would be significantly beneficial for hydrogen production via electrocatalytic hydrogen evolution reaction (HER). All candidates thus far are exclusively metallic catalysts which suffer inherent corrosion and oxidation susceptibility during acidic proton-exchange membrane electrolysis. Herein based on theoretical predictions we designed and synthesized nitrogen (N) and phosphorus (P) dual-doped graphene as a non-metallic electrocatalyst for sustainable and efficient hydrogen production. The N and Phetero-atoms could coactivate the adjacent C atom in the graphene matrix by affecting its valence orbital energy levels to induce a synergistically enhanced reactivity toward HER. As a result the dual-doped graphene showed higher electrocatalytic HER activity than single-doped ones and comparable performance to some of the traditional metallic catalysts.
Finding Synergy Between Renewables and Coal: Flexible Power and Hydrogen Production from Advanced IGCC Plants with Integrated CO2 Capture
Feb 2021
Publication
Variable renewable energy (VRE) has seen rapid growth in recent years. However VRE deployment requires a fleet of dispatchable power plants to supply electricity during periods with limited wind and sunlight. These plants will operate at reduced utilization rates that pose serious economic challenges. To address this challenge this paper presents the techno-economic assessment of flexible power and hydrogen production from integrated gasification combined cycles (IGCC) employing the gas switching combustion (GSC) technology for CO2 capture and membrane assisted water gas shift (MAWGS) reactors for hydrogen production. Three GSC-MAWGS-IGCC plants are evaluated based on different gasification technologies: Shell High Temperature Winkler and GE. These advanced plants are compared to two benchmark IGCC plants one without and one with CO2 capture. All plants utilize state-of-the-art H-class gas turbines and hot gas clean-up for maximum efficiency. Under baseload operation the GSC plants returned CO2 avoidance costs in the range of 24.9–36.9 €/ton compared to 44.3 €/ton for the benchmark. However the major advantage of these plants is evident in the more realistic mid-load scenario. Due to the ability to keep operating and sell hydrogen to the market during times of abundant wind and sun the best GSC plants offer a 6–11%-point higher annual rate of return than the benchmark plant with CO2 capture. This large economic advantage shows that the flexible GSC plants are a promising option for balancing VRE provided a market for the generated clean hydrogen exists.
Onboard Compressed Hydrogen Storage: Fast Filling Experiments and Simulations
Nov 2021
Publication
Technology safety represents a key enabling factor for the commercial use of hydrogen within the automotive industry. In the last years considerable pre-normative and normative research effort has produced regulations at national European and global level as well as international standards. Their validation is at the moment on going internationally. Additional research is required to improve this regulatory and standardization frame which is also expected to have a beneficial effect on cost and product optimization. The present paper addresses results related to the experimental assessment and modeling of safety performance of high pressure onboard storage. To simulate the lifetime of onboard hydrogen tanks commercial tanks have been subjected to filling-emptying cycles encompassing a fast-filling phase as prescribed by the European regulation on type-approval of hydrogen vehicles. The local temperature history inside the tanks has been measured and compared with the temperature outside at the tank metallic bosses which is the measurement location identified by the regulation. Experimental activities are complemented by computational fluid-dynamics (CFD) modeling of the fast-filling process by means of a numerical model previously validated. The outcome of these activities is a set of scientifically based data which will serve as input to future regulations and standards improvement.
Challenges in Hydrogen RCS’ Stakeholder Engagement in South Africa
Sep 2019
Publication
There is a great deal of knowledge and experience on the safe handling of hydrogen and the safe operation and management of hydrogen systems in South Africa. This knowledge and experience mostly sits within large gas supply companies and other large producers and consumers of hydrogen. However there appears to be less experience leading to a level of discomfort within regulatory bodies such as provincial and municipal fire departments and the national standards association. This compounded by a national policy of disallowing gas cylinders indoors has resulted in delays and indeed stalling in the process of obtaining permission to operate laboratories such as those of the national hydrogen programme HySA. In an effort to break this impasse two workshops were organised by HySA. The first was held at the CSIR’s facilities in Pretoria in October 2016. The second was held at the campus of the University of the Western Cape in Cape Town in May 2018. Four international experts and local experts in hydrogen regulations codes standards and safety addressed the 50-strong South African audiences via 5-way videoconferencing. This proved to be a very powerful tool to educate the audience and in particular the Tshwane (Pretoria) and Western Cape Fire Departments on the real issues risks and safety of hydrogen. The paper describes the South African Hydrogen RCS landscape the organisation and running of the workshops and the outputs achieved.
Hydrogen-based Systems for Integration of Renewable Energy in Power Systems: Achievements and Perspectives
Jul 2021
Publication
This paper is a critical review of selected real-world energy storage systems based on hydrogen ranging from lab-scale systems to full-scale systems in continuous operation. 15 projects are presented with a critical overview of their concept and performance. A review of research related to power electronics control systems and energy management strategies has been added to integrate the findings with outlooks usually described in separate literature. Results show that while hydrogen energy storage systems are technically feasible they still require large cost reductions to become commercially attractive. A challenge that affects the cost per unit of energy is the low energy efficiency of some of the system components in real-world operating conditions. Due to losses in the conversion and storage processes hydrogen energy storage systems lose anywhere between 60 and 85% of the incoming electricity with current technology. However there are currently very few alternatives for long-term storage of electricity in power systems so the interest in hydrogen for this application remains high from both industry and academia. Additionally it is expected that the share of intermittent renewable energy in power systems will increase in the coming decades. This could lead to technology development and cost reductions within hydrogen technology if this technology is needed to store excess renewable energy. Results from the reviewed projects indicate that the best solution from a technical viewpoint consists in hybrid systems where hydrogen is combined with short-term energy storage technologies like batteries and supercapacitors. In these hybrid systems the advantages with each storage technology can be fully exploited to maximize efficiency if the system is specifically tailored to the given situation. The disadvantage is that this will obviously increase the complexity and total cost of the energy system.<br/>Therefore control systems and energy management strategies are important factors to achieve optimal results both in terms of efficiency and cost. By considering the reviewed projects and evaluating operation modes and control systems new hybrid energy systems could be tailored to fit each situation and to reduce energy losses.
A Review at the Role of Storage in Energy Systems with a Focus on Power to Gas and Long-term Storage
Aug 2017
Publication
A review of more than 60 studies (plus m4ore than 65 studies on P2G) on power and energy models based on simulation and optimization was done. Based on these for power systems with up to 95% renewables the electricity storage size is found to be below 1.5% of the annual demand (in energy terms). While for 100% renewables energy systems (power heat mobility) it can remain below 6% of the annual energy demand. Combination of sectors and diverting the electricity to another sector can play a large role in reducing the storage size. From the potential alternatives to satisfy this demand pumped hydro storage (PHS) global potential is not enough and new technologies with a higher energy density are needed. Hydrogen with more than 250 times the energy density of PHS is a potential option to satisfy the storage need. However changes needed in infrastructure to deal with high hydrogen content and the suitability of salt caverns for its storage can pose limitations for this technology. Power to Gas (P2G) arises as possible alternative overcoming both the facilities and the energy density issues. The global storage requirement would represent only 2% of the global annual natural gas production or 10% of the gas storage facilities (in energy equivalent). The more options considered to deal with intermittent sources the lower the storage requirement will be. Therefore future studies aiming to quantify storage needs should focus on the entire energy system including technology vectors (e.g. Power to Heat Liquid Gas Chemicals) to avoid overestimating the amount of storage needed.
On the Climate Impacts of Blue Hydrogen Production
Nov 2021
Publication
Natural gas based hydrogen production with carbon capture and storage is referred to as blue hydrogen. If substantial amounts of CO2 from natural gas reforming are captured and permanently stored such hydrogen could be a low-carbon energy carrier. However recent research raises questions about the effective climate impacts of blue hydrogen from a life cycle perspective. Our analysis sheds light on the relevant issues and provides a balanced perspective on the impacts on climate change associated with blue hydrogen. We show that such impacts may indeed vary over large ranges and depend on only a few key parameters: the methane emission rate of the natural gas supply chain the CO2 removal rate at the hydrogen production plant and the global warming metric applied. State-of-the-art reforming with high CO2 capture rates combined with natural gas supply featuring low methane emissions does indeed allow for substantial reduction of greenhouse gas emissions compared to both conventional natural gas reforming and direct combustion of natural gas. Under such conditions blue hydrogen is compatible with low-carbon economies and exhibits climate change impacts at the upper end of the range of those caused by hydrogen production from renewable-based electricity. However neither current blue nor green hydrogen production pathways render fully “net-zero” hydrogen without additional CO2 removal.
Photocatalytic Hydrogen Production by Photo-Reforming of Methanol with One-pot Synthesized Pt-containing TiO2 Photocatalysts
Jul 2019
Publication
Functionalization of semiconductors by metallic nanoparticle is considered to be one of the most effective procedure to improve photocatalytic hydrogen production. Photodeposition is frequently used for functionalization but particle sizes and dispersions are still difficult to control. Here Pt functionalization is achieved in a one-pot synthesis. The as-prepared samples are compared to reference materials prepared by conventional photodeposition and our results confirm that small and well-dispersed nanoparticles with superior stability are obtained by one-pot synthesis. The enhanced stability is attributed to a limited leaching of Pt nanoparticles during illumination likely caused by the preferable interaction of small well dispersed Pt nanoparticles with the TiO2 support material. In addition our results demonstrate that Na-residues are detrimental for the photocatalytic performance and washing in acidic solution is mandatory to effectively reduce the sodium contamination.
A Multi-objective MILP Model for the Design and Operation of Future Integrated Multi-vector Energy Networks Capturing Detailed Spatio-temporal Dependencies
Dec 2017
Publication
A multi-objective optimisation model based on mixed integer linear programming is presented that can simultaneously determine the design and operation of any integrated multi-vector energy networks. It can answer variants of the following questions: What is the most effective way in terms of cost value/profit and/or emissions of designing and operating the integrated multi-vector energy networks that utilise a variety of primary energy sources to deliver different energy services such as heat electricity and mobility given the availability of primary resources and the levels of demands and their distribution across space and time? When to invest in technologies where to locate them; what resources should be used where when and how to convert them to the energy services required; how to transport the resources and manage inventory? Scenarios for Great Britain were examined involving different primary energy sources such as natural gas biomass and wind power in order to satisfy demands for heat electricity and mobility via various energy vectors such as electricity natural gas hydrogen and syngas. Different objectives were considered such as minimising cost maximising profit minimising emissions and maximising renewable energy production subject to the availability of suitable land for biomass and wind turbines as well as the maximum local production and import rates for natural gas. Results suggest that if significant mobility demands are met by hydrogen-powered fuel cell vehicles then hydrogen is the preferred energy vector over natural gas for satisfying heat demands. If natural gas is not used and energy can only be generated from wind power and biomass electricity and syngas are the preferred energy carriers for satisfying electricity and heat demands.
The Hydrogen Economy and Jobs of the Future
Nov 2018
Publication
Growth in the hydrogen and fuel cell industries will lead to vast new employment opportunities and these will be created in a wide variety of industries skills tasks and earnings. Many of these jobs do not currently exist and do not have occupational titles defined in official classifications. In addition many of these jobs require different skills and education than current jobs and training requirements must be assessed so that this rapidly growing part of the economy has a sufficient supply of trained and qualified workers. We discuss the current hydrogen economy and technologies. We then identify by occupational titles the new jobs that will be created in the expanding hydrogen/fuel cell economy estimate the average US salary for each job identify the minimum educational attainment required to gain entry into that occupation and specify the recommended university degree for the advanced educational requirements. We provide recommendations for further research.
Prediction of Gaseous Products from Refuse Derived Fuel Pyrolysis Using Chemical Modelling Software - Ansys Chemkin-Pro
Nov 2019
Publication
There can be observed global interest in waste pyrolysis technology due to low costs and availability of raw materials. At the same time there is a literature gap in forecasting environmental effects of thermal waste treatment installations. In the article was modelled the chemical composition of pyrolysis gas with main focus on the problem in terms of environmental hazards. Not only RDF fuel was analysed but also selected waste fractions included in its composition. This approach provided comprehensive knowledge about the chemical composition of gaseous pyrolysis products which is important from the point of view of the heterogeneity of RDF fuel. The main goal of this article was to focus on the utilitarian aspect of the obtained calculation results. Final results can be the basis for estimating ecological effects both for existing and newly designed installations.
Pyrolysis process was modelled using Ansys Chemkin-Pro software. The investigation of the process were carried out for five different temperatures (700 750 800 850 and 900 °C). As an output the mole fraction of H2 H2O CH4 C2H2C2H4 C3H6 C3H8 CO CO2 HCl and H2S were presented. Additionally the reaction pathways for selected material were presented.
Based on obtained results it was established that the residence time did not influenced on the concentration of products contrary to temperature. The chemical composition of pyrolytic gas is closely related to wastes origin. The application of Chemkin-Pro allowed the calculation of formation for each products at different temperatures and formulation of hypotheses on the reaction pathways involved during pyrolysis process. Further based on the obtained results confirmed the possibilities of using pyrolysis gas from RDF as a substitute for natural gas in energy consumption sectors. Optimization of the process can be conducted with low financial outlays and reliable results by using calculation tools. Moreover it can be predicted negative impact of obtained products on the future installation.
Pyrolysis process was modelled using Ansys Chemkin-Pro software. The investigation of the process were carried out for five different temperatures (700 750 800 850 and 900 °C). As an output the mole fraction of H2 H2O CH4 C2H2C2H4 C3H6 C3H8 CO CO2 HCl and H2S were presented. Additionally the reaction pathways for selected material were presented.
Based on obtained results it was established that the residence time did not influenced on the concentration of products contrary to temperature. The chemical composition of pyrolytic gas is closely related to wastes origin. The application of Chemkin-Pro allowed the calculation of formation for each products at different temperatures and formulation of hypotheses on the reaction pathways involved during pyrolysis process. Further based on the obtained results confirmed the possibilities of using pyrolysis gas from RDF as a substitute for natural gas in energy consumption sectors. Optimization of the process can be conducted with low financial outlays and reliable results by using calculation tools. Moreover it can be predicted negative impact of obtained products on the future installation.
Renewable Hydrogen Production from Butanol Steam Reforming over Nickel Catalysts Promoted by Lanthanides
Oct 2021
Publication
Hydrogen is mainly produced by steam reforming of natural gas a non-renewable resource. Alternative and renewable routes for hydrogen production play an important role in reducing dependence on oil and minimizing the emission of greenhouse gases. In this work butanol a model compound of bio-oil was employed for hydrogen production by steam reforming. The reaction was evaluated for 30 h in a tubular quartz reactor at 500 ◦C atmospheric pressure GHSV of 500000 h−1 and an aqueous solution feed of 10% v/v butanol. For this reaction catalysts with 20 wt.% NiO were prepared by wet impregnation using three supports: γ-alumina and alumina modified with 10 wt.% of cerium and lanthanum oxides. Both promoters increased the reduction degree of the catalysts and decreased catalyst acidity which is closely related to coke formation and deactivation. Ni/La2O3– Al2O3 presented a higher nickel dispersion (14.6%) which combined with other properties led to a higher stability higher mean hydrogen yield (71%) and lower coke formation per mass (56%). On the other hand the nonpromoted catalyst suffered a significant deactivation associated with coke formation favored by its highest acidity (3.1 µmol m−2 ).
Preliminary Design of a Self-Sufficient Electrical Storage System Based on Electrolytic Hydrogen for Power Supply in a Residential Application
Oct 2021
Publication
The use of renewable energy and hydrogen technology is a sustainable solution for the intermittent feature of renewable energies. Hence the aim of the present work is to design a self-sufficient system for a one-family house by coupling a solar photovoltaic array and an anion exchange membrane water electrolyzer (AEMWE). The first step is the selection of the photovoltaic panel by using PV-SYST 7.0 software. Then the hydrogen production system is calculated by coupling the electrolyzer and photovoltaic panel current–potential curves. A fuel cell is selected to use the hydrogen produced when solar energy is not available. Finally the hydrogen storage tank is also estimated to store hydrogen for a design basis of four consecutive cloudy days according to the hydrogen consumption of the fuel cell. The whole system is designed by a simple procedure for a specific location in Ciudad Real (Spain) for January which is known as the coldest month of the year. The simple procedure described in this work could be used elsewhere and demonstrated that the hydrogen production at low scale is a suitable technology to use renewable energy for self-energy supporting in a residential application without any connection to the grid.
Techno-Economic Analysis of the Hybrid Solar PV/H/Fuel Cell Based Supply Scheme for Green Mobile Communication
Nov 2021
Publication
Hydrogen has received tremendous global attention as an energy carrier and an energy storage system. Hydrogen carrier introduces a power to hydrogen (P2H) and power to hydrogen to power (P2H2P) facility to store the excess energy in renewable energy storage systems with the facts of large-scale storage capacity transportability and multiple utilities. This work examines the techno-economic feasibility of hybrid solar photovoltaic (PV)/hydrogen/fuel cell-powered cellular base stations for developing green mobile communication to decrease environmental degradation and mitigate fossil-fuel crises. Extensive simulation is carried out using a hybrid optimization model for electric renewables (HOMER) optimization tool to evaluate the optimal size energy production total production cost per unit energy production cost and emission of carbon footprints subject to different relevant system parameters. In addition the throughput and energy efficiency performance of the wireless network is critically evaluated with the help of MATLAB-based Monte-Carlo simulations taking multipath fading system bandwidth transmission power and inter-cell interference (ICI) into consideration. Results show that a more stable and reliable green solution for the telecommunications sector will be the macro cellular basis stations driven by the recommended hybrid supply system. The hybrid supply system has around 17% surplus electricity and 48.1 h backup capacity that increases the system reliability by maintaining a better quality of service (QoS). To end the outcomes of the suggested system are compared with the other supply scheme and the previously published research work for justifying the validity of the proposed system.
Pyrolysis-gasification of Wastes Plastics for Syngas Production Using Metal Modified Zeolite Catalysts Under Different Ratio of Nitrogen/Oxygen
Jun 2020
Publication
The aim of this study was the syngas production by the gasification of plastic waste (polyethylene polypropylene and terephthalate polyethylene). Ca Ce La Mg and Mn were used to promote the Ni/ZSM-5 catalyst in order to enhance the production of higher syngas yield. The modified catalysts can enhanced the reaction rate of the pyrolysis process and resulting in high syngas in the product yields. Especially cerium lanthanum promoted catalysts can enhance the yield of syngas. The effect of the reaction temperature and nitrogen/oxygen ratio of the carrier gas was also investigated. The maximum syngas production was obtained with lanthanum catalyst (112.2 mmol/g (95%N2 and 5%O2) and 130.7 mmol/g (90%N2 and 10%O2) at 850 °C. Less carbon depositions was found at 850 °C or even by the using of catalyst and more oxygen in the carrier gas. The oxygen content of the pyrolysis-gasification atmosphere had a key role to the syngas yield and affects significantly the carbon-monoxide/carbon-dioxide ratio. Catalysts can also accelerate the methanization reactions and isomerize the main carbon frame. Increasing in both temperature and oxygen in the atmosphere led to higher n-paraffin/n-olefin ratio and more multi-ring aromatic hydrocarbons in pyrolysis oils. The concentration of hydrocarbons containing oxygen and branched compounds was also significantly affected by catalysts.
A Review of Hydrogen Purification Technologies for Fuel Cell Vehicles
Mar 2021
Publication
Nowadays we face a series of global challenges including the growing depletion of fossil energy environmental pollution and global warming. The replacement of coal petroleum and natural gas by secondary energy resources is vital for sustainable development. Hydrogen (H2 ) energy is considered the ultimate energy in the 21st century because of its diverse sources cleanliness low carbon emission flexibility and high efficiency. H2 fuel cell vehicles are commonly the end-point application of H2 energy. Owing to their zero carbon emission they are gradually replacing traditional vehicles powered by fossil fuel. As the H2 fuel cell vehicle industry rapidly develops H2 fuel supply especially H2 quality attracts increasing attention. Compared with H2 for industrial use the H2 purity requirements for fuel cells are not high. Still the impurity content is strictly controlled since even a low amount of some impurities may irreversibly damage fuel cells’ performance and running life. This paper reviews different versions of current standards concerning H2 for fuel cell vehicles in China and abroad. Furthermore we analyze the causes and developing trends for the changes in these standards in detail. On the other hand according to characteristics of H2 for fuel cell vehicles standard H2 purification technologies such as pressure swing adsorption (PSA) membrane separation and metal hydride separation were analyzed and the latest research progress was reviewed.
Hydrogen Production Methods Based on Solar and Wind Energy: A Review
Jan 2023
Publication
Several research works have investigated the direct supply of renewable electricity to electrolysis particularly from photovoltaic (PV) and wind generator (WG) systems. Hydrogen (H2 ) production based on solar energy is considered to be the newest solution for sustainable energy. Different technologies based on solar energy which allow hydrogen production are presented to study their benefits and inconveniences. The technology of water decomposition based on renewable energy sources to produce hydrogen can be achieved by different processes (photochemical systems; photocatalysis systems photo-electrolysis systems bio-photolysis systems thermolysis systems thermochemical cycles steam electrolysis hybrid processes and concentrated solar energy systems). A comparison of the different methods for hydrogen production based on PV and WG systems was given in this study. A comparative study of different types of electrolyzers was also presented and discussed. Finally an economic assessment of green hydrogen production is given. The hydrogen production cost depends on several factors such as renewable energy sources electrolysis type weather conditions installation cost and the productivity of hydrogen per day. PV/H2 and wind/H2 systems are both suitable in remote and arid areas. Minimum maintenance is required and a power cycle is not needed to produce electricity. The concentrated CSP/H2 system needs a power cycle. The hydrogen production cost is higher if using wind/H2 rather than PV/H2 . The green energy sources are useful for multiple applications such as hydrogen production cooling systems heating and water desalination.
Development of Water Electrolysis in the European Union
Feb 2014
Publication
In view of the recent interest in the transformation of renewable energy into a new energy vector that did not produce by combustion greenhouse gases emissions the Fuel Cells and Hydrogen Joint Undertaking (FCH JU) commissioned this report to a consultancy to get a better understanding of the industrial perspectives of water electrolysis in Europe. and the role that public support has in that evolution.
Development and Future Scope of Renewable Energy and Energy Storage Systems
May 2022
Publication
This review study attempts to summarize available energy storage systems in order to accelerate the adoption of renewable energy. Inefficient energy storage systems have been shown to function as a deterrent to the implementation of sustainable development. It is therefore critical to conduct a thorough examination of existing and soon-to-be-developed energy storage technologies. Various scholarly publications in the fields of energy storage systems and renewable energy have been reviewed and summarized. Data and themes have been further highlighted with the use of appropriate figures and tables. Case studies and examples of major projects have also been researched to gain a better understanding of the energy storage technologies evaluated. An insightful analysis of present energy storage technologies and other possible innovations have been discovered with the use of suitable literature review and illustrations. This report also emphasizes the critical necessity for an efficient storage system if renewable energy is to be widely adopted.
The Czech Republic's Hydrogen Strategy
Jul 2021
Publication
The Czech Republic’s Hydrogen Strategy is being developed in the context of the Hydrogen Strategy for a climate neutral Europe which reflects the European Green Deal objective of climate neutrality by 2050. The objective of the Strategy is thus to reduce greenhouse gas emissions in such a way that the economy shifts smoothly to low-carbon technologies.
This is associated with two strategic goals:
This is associated with two strategic goals:
- Reduce greenhouse gas emissions
- Stimulate the economic growth
- Volume of low-carbon hydrogen production
- Volume of low-carbon hydrogen consumption
- Infrastructure readiness for hydrogen transport and storage
- Progress in R&D and production of hydrogen technologies
- Low-carbon hydrogen production
- Low-carbon hydrogen use
- Hydrogen transport and storage
- Hydrogen technologies
Future Heat Series Part 2 - Policy for Heat
Oct 2015
Publication
Policy for Heat: Transforming the System urges Government to implement an ambitious long-term decarbonisation strategy for the heat sector before it’s too late in new inquiry report. The report builds on the work of Part 1 in the Future Heat Series which compared recent decarbonisation pathways and analyses to identify and highlight key policy mechanisms and transitions that are needed in order to decarbonise heat for buildings by 2050. Chaired by Shadow Energy Minister Jonathan Reynolds MP and Conservative MP Rebecca Pow (and also previous MP and member of the Energy and Climate Change Select Committee Dan Byles MP until he stood down at the General Election) the report is written by cross-party think tank group Carbon Connect. The report was published in Parliament at a cross-party debate on Wednesday 14th October. Sponsored by Energy & Utilities Alliance (EUA) and the Institution of Gas Engineers and Managers (IGEM) the report is the second in a cross-party and independent inquiry series.
Everything About Hydrogen Podcast: Why the Fuel Cell World is Different This Time
Aug 2019
Publication
The fuel cell game is not new and for many it is has been a long time coming. Few know this better than Ballard Power Systems the third ever founded Fuel Cell company that has operated since the 1970s. On the show we ask Nicolas Pocard about Ballards history and why this time the market is different for fuel cell companies.
The podcast can be found on their website
The podcast can be found on their website
Novel Biofuel Cell Using Hydrogen Generation of Photosynthesis
Nov 2020
Publication
Energies based on biomaterials attract a lot of interest as next-generation energy because biomaterials are environmentally friendly materials and abundant in nature. Fuel cells are also known as the clean and important next-generation source of energy. In the present study to develop the fuel cell based on biomaterials a novel biofuel cell which consists of collagen electrolyte and the hydrogen fuel generated from photochemical system II (PSII) in photosynthesis has been fabricated and its property has been investigated. It was found that the PSII solution in which PSII was extracted from the thylakoid membrane using a surfactant generates hydrogen by the irradiation of light. The typical hydrogen-generating rate is approximately 7.41 × 1014 molecules/s for the light intensity of 0.5 mW/cm2 for the PSII solution of 5 mL. The biofuel cell using the PSII solution as the fuel exhibited approximately 0.12 mW/cm2 . This result indicates that the fuel cell using the collagen electrolyte and the hydrogen fuel generated from PSII solution becomes the new type of biofuel cell and will lead to the development of the next-generation energy
Ultra-clean Hydrogen Production by Ammonia Decomposition
Jan 2016
Publication
A rigorous heterogeneous mathematical model is used to simulate a cascade of multi-stage fixed bed membrane reactors (MSFBMR) with inter-stage heating and fresh sweep gas for the decomposition of ammonia to produce high purity hydrogen suitable for the PEM fuel cells. Different reactor configurations are compared. The comparison between a single fixed bed reactor (FBR) and a single fixed bed membrane reactor (FBMR) shows that the FBMR is superior to the FBR and gives 60.48% ammonia conversion higher than the FBR. However 20.91% exit ammonia conversion obtained by the FBMR is considered to be poor. The FBMR is limited by the kinetics at low temperatures. The numerical results show that the MSFBMR of four beds achieve 100.0% ammonia conversion. It was found that the membrane plays the prime role in the displacement of the thermodynamic equilibrium. The results also show that a linear relationship exists between the number of beds and the feed temperature and a correlation has been developed. A critical point for an effective hydrogen permeation zone has been identified. It is observed that the diffusion limitation is confined to a slim region at the entrance of the reactor. It is also observed that the heat load assumes a maximum inflection point and explanations offered. The results show that the multi-stage configuration has a promising potential to be applied successfully on-site for ultra-clean hydrogen production.
Energy Transition Outlook 2021: Technology Progress Report
Jun 2021
Publication
This report is part of DNV’s suite of Energy Transition Outlook publications for 2021. It focuses on how key energy transition technologies will develop compete and interact in the coming five years.
Debate and uncertainty about the energy transition tend to focus on what technology can and can’t do. All too often such discussions involve wishful thinking advocacy of a favoured technology or reference to outdated information. Through this report we bring insights derived from our daily work with the world’s leading energy players including producers transporters and end users. Each of the ten chapters that follow are written by our experts in the field – or in the case of maritime technologies on the ocean.
Because the pace of the transition is intensifying describing any given technology is like painting a fast-moving train. We have attempted to strike a balance between technical details and issues of safety efficiency cost and competitiveness. Transition technologies are deeply interlinked and in some cases interdependent; any discussion on green hydrogen for example must account for developments in renewable electricity hydrogen storage and transport systems and end-use technologies such as fuels cells.
Our selection of ten technologies is not exhaustive but each of these technologies is of particular interest for the pace and direction of the energy transition. They range from relatively mature technologies like solar PV to technologies like nuclear fusion which are some distance from commercialization but which have current R&D and prototyping worth watching. Together they cover most but not all key sectors. We describe expected developments for the coming five years which to a large extent will determine how the energy transition unfolds through to mid-century. As such this Technology Progress report is an essential supplement to our main Energy Transition Outlook forecast.
Our aim is to make an objective and realistic assessment of the status of these technologies and evaluate how they contribute to the energy transition ahead. Attention to progress in these technologies will be critical for anyone concerned with energy.
Debate and uncertainty about the energy transition tend to focus on what technology can and can’t do. All too often such discussions involve wishful thinking advocacy of a favoured technology or reference to outdated information. Through this report we bring insights derived from our daily work with the world’s leading energy players including producers transporters and end users. Each of the ten chapters that follow are written by our experts in the field – or in the case of maritime technologies on the ocean.
Because the pace of the transition is intensifying describing any given technology is like painting a fast-moving train. We have attempted to strike a balance between technical details and issues of safety efficiency cost and competitiveness. Transition technologies are deeply interlinked and in some cases interdependent; any discussion on green hydrogen for example must account for developments in renewable electricity hydrogen storage and transport systems and end-use technologies such as fuels cells.
Our selection of ten technologies is not exhaustive but each of these technologies is of particular interest for the pace and direction of the energy transition. They range from relatively mature technologies like solar PV to technologies like nuclear fusion which are some distance from commercialization but which have current R&D and prototyping worth watching. Together they cover most but not all key sectors. We describe expected developments for the coming five years which to a large extent will determine how the energy transition unfolds through to mid-century. As such this Technology Progress report is an essential supplement to our main Energy Transition Outlook forecast.
Our aim is to make an objective and realistic assessment of the status of these technologies and evaluate how they contribute to the energy transition ahead. Attention to progress in these technologies will be critical for anyone concerned with energy.
Decarbonizing the German Industrial Thermal Energy Use with Solar, Hydrogen, and Other Options - Recommendations for the World
Nov 2022
Publication
This paper is based on a position paper of the German Industry Association Concentrated Solar Power e.V. to the German government and discusses options on how to decarbonize the heat demand of the domestic industry. Among other option concentration solar collectors are a suitable option in Germany which has not been expected by many experts. The paper derives requirements that are needed to ensure a quick and sustainable way to decarbonize industrial heat demand. They are considered to also be relevant for many other countries that follow the same ambition to become climate neutral in the next decades. They major statements are: A mix of different renewable energy technologies in conjunction with efficiency measures is needed to ensure a secure climate-friendly and cost-efficient heat supply for the industry; The different technology options for the provision of heat from renewable sources through electrification and through hydrogen can and must be combined and integrated with each other. In this context concentrating solar thermal represents an important part of the hybrid supply portfolio of a decarbonized industry This requires: The definition of an expansion target for process heat and the flanking measures; Ensuring the equivalence of renewable heat renewable electricity and green hydrogen - also as hybrid solutions; The promotion of concentrating solar thermal reference projects as an impetus for market ramp-up in Germany; The launch of an information campaign for heat consumers and the establishment of a pool of consultants.
Detecting Hydrogen Concentrations During Admixing Hydrogen in Natural Gas Grids
Aug 2021
Publication
The first applications of hydrogen in a natural gas grid will be the admixing of low concentrations in an existing distribution grid. For easy quality and process control it is essential to monitor the hydrogen concentration in real time preferably using cost effective monitoring solutions. In this paper we introduce the use of a platinum based hydrogen sensor that can accurately (at 0.1 vol%) and reversibly monitor the concentration of hydrogen in a carrier gas. This carrier gas that can be nitrogen methane or natural gas has no influence on the accuracy of the hydrogen detection. The hydrogen sensor consists of an interdigitated electrode on a chip coated with a platinum nanocomposite layer that interacts with the gas. This chip can be easily added to a gas sensor for natural gas and biogas that was already developed in previous research. Just by the addition of an extra chip we extended the applicability of the natural gas sensor to hydrogen admixing. The feasibility of the sensor was demonstrated in our own (TNO) laboratory and at a field test location of the HyDeploy program at Keele University in the U.K
A CFD Analysis of Liquid Hydrogen Vessel Explosions using the ADREA-HF Code
Sep 2021
Publication
Despite hydrogen is one of the most suitable candidates in replacing fossil fuels its very low densityrepresents a drawback when it is stored. The liquefaction process can increase the hydrogen densityand therefore enhance its storage capacity. The boiling liquid expanding vapour explosion (BLEVE) isa typical accident scenario that must be always considered when liquefied gases are stored. Inparticular BLEVE is a physical explosion with low probabilities and high consequences which mayoccur after the catastrophic rupture of a vessel containing a liquid with a temperature above its boilingpoint at atmospheric pressure. In this paper a parametric CFD analysis of the BLEVE phenomenonwas conducted by means of the CFD code ADREA-HF for liquid hydrogen (LH2) vessels. Firstly theCFD model is validated against a well-documented CO2 BLEVE experiment. Next hydrogen BLEVEcases are examined. The physical parameters were chosen based on the BMW tests carried out in the1990s on LH2 tanks designed for automotive purposes. Different filling degrees initial pressures andtemperatures of the tank content are simulated to comprehend how the blast wave is influenced by theinitial conditions. The aim of this study is twofold: provide new insights and observations on theBLEVE dynamics and demonstrate the CFD tool effectiveness for conducting the consequenceanalysis and thus aiding the risk assessment of liquefied gas vessel explosion. Good agreement wasshown between the simulation outcomes and the experimental results.
The Role of Hydrogen in Achieving Long Term Japanese Energy System Goals
Sep 2020
Publication
This research qualitatively reviews literature regarding energy system modeling in Japan specific to the future hydrogen economy leveraging quantitative model outcomes to establish the potential future deployment of hydrogen in Japan. The analysis focuses on the four key sectors of storage supplementing the gas grid power generation and transportation detailing the potential range of hydrogen technologies which are expected to penetrate Japanese energy markets up to 2050 and beyond. Alongside key model outcomes the appropriate policy settings governance and market mechanisms are described which underpin the potential hydrogen economy future for Japan. We find that transportation gas grid supplementation and storage end-uses may emerge in significant quantities due to policies which encourage ambitious implementation targets investment in technologies and research and development and the emergence of a future carbon pricing regime. On the other hand for Japan which will initially be dependent on imported hydrogen the cost of imports appears critical to the emergence of broad hydrogen usage particularly in the power generation sector. Further the consideration of demographics in Japan recognizing the aging shrinking population and peoples’ energy use preferences will likely be instrumental in realizing a smooth transition toward a hydrogen economy.
Everything About Hydrogen Podcast: Championing a Clean Energy Future
Nov 2021
Publication
With COP starting this week we discuss with the HLC team the role of hydrogen in decarbonization and the critical need for hydrogen to scale quickly. Andrew and Patrick sit down with Kieran Coleman Energy & Industry Lead for the United Nations COP High Level Champions to chat about the work being done in advance of COP with partners and the level of ambition we’ve seen across various sectors about the future of hydrogen and a lot more!
The podcast can be found on their website
The podcast can be found on their website
Transitioning Remote Arctic Settlements to Renewable Energy Systems – A Modelling Study of Longyearbyen, Svalbard
Nov 2019
Publication
As transitioning away from fossil fuels to renewable energy sources comes on the agenda for a range of energy systems energy modelling tools can provide useful insights. If large parts of the energy system turns out to be based on variable renewables an accurate representation of their short-term variability in such models is crucial. In this paper we have developed a stochastic long-term energy model and applied it to an isolated Arctic settlement as a challenging and realistic test case. Our findings suggest that the stochastic modelling approach is critical in particular for studies of remote Arctic energy systems. Furthermore the results from a case study of the Norwegian settlement of Longyearbyen suggest that transitioning to a system based on renewable energy sources is feasible. We recommend that a solution based mainly on renewable power generation but also including energy storage import of hydrogen and adequate back-up capacity is taken into consideration when planning the future of remote Arctic settlements.
Balancing Wind-power Fluctuation Via Onsite Storage Under Uncertainty Power-to-hydrogen-to-power Versus Lithium Battery
Oct 2019
Publication
Imbalance costs caused by forecasting errors are considerable for grid-connected wind farms. In order to reduce such costs two onsite storage technologies i.e. power-to-hydrogen-to-power and lithium battery are investigated considering 14 uncertain technological and economic parameters. Probability density distributions of wind forecasting errors and power level are first considered to quantify the imbalance and excess wind power. Then robust optimal sizing of the onsite storage is performed under uncertainty to maximize wind-farm profit (the net present value). Global sensitivity analysis is further carried out for parameters prioritization to highlight the key influential parameters. The results show that the profit of power-to-hydrogen-to-power case is sensitive to the hydrogen price wind forecasting accuracy and hydrogen storage price. When hydrogen price ranges in (2 6) €/kg installing only electrolyzer can earn profits over 100 k€/MWWP in 9% scenarios with capacity below 250 kW/MWWP under high hydrogen price (over 4 €/kg); while installing only fuel cell can achieve such high profits only in 1.3% scenarios with capacity below 180 kW/MWWP. Installing both electrolyzer and fuel cell (only suggested in 22% scenarios) results in profits below 160 k€/MWWP and particularly 20% scenarios allow for a profit below 50 k€/MWWP due to the contradictory effects of wind forecasting error hydrogen and electricity price. For lithium battery investment cost is the single highly influential factor which should be reduced to 760 €/kWh. The battery capacity is limited to 88 kW h/MWWP. For profits over 100 k€/MWWP (in 3% scenarios) the battery should be with an investment cost below 510 €/kWh and a depth of discharge over 63%. The power-to-hydrogen-to-power case is more advantageous in terms of profitability reliability and utilization factor (full-load operating hours) while lithium battery is more helpful to reduce the lost wind and has less environmental impact considering current hydrogen market.
Development of Analysis Program for Direct Containment Heating
Feb 2022
Publication
Direct containment heating (DCH) is one of the potential factors leading to early containment failure. DCH is closely related to safety analysis and containment performance evaluation of nuclear power plants. In this study a DCH prediction program was developed to analyze the DCH loads of containment vessel. The phenomenological model of debris dispersal metal oxidation reaction debris-atmospheric heat transfer and hydrogen jet burn was established. Code assessment was performed by comparing with several separate effect tests and integral effect tests. The comparison between the predicted results and experimental data shows that the program can predict the key parameters such as peak pressure temperature and hydrogen production in containment well and for most comparisons the relative errors can be maintained within 20%. Among them the prediction uncertainty of hydrogen production is slightly larger. The analysis shows that the main sources of the error are the difference of time scale and the oxidation of cavity debris.
Numerical Simulation of Leaking Hydrogen Dispersion Behavior
Sep 2021
Publication
As one kind of clean zero carbon and sustainable energy hydrogen energy has been regarded as the most potential secondary energy. Recently hydrogen refueling station gradually becomes one of important distribution infrastructures that provides hydrogen sources for transport vehicles and other distribution devices. However the highly combustible nature of hydrogen may bring great hazards to environment and human. The safety design of hydrogen usage has been brought to public too. This paper is mainly focused on the hydrogen leakage and dispersion process. A new solver for gaseous buoyancy dispersion process is developed based on OpenFOAM [1]. Thermodynamic and transport properties of gases are updated by library Mutation ++ [2]. For validation two tests of hydrogen dispersion in partially opened space and closed space are presented. Numerical simulation of hydrogen dispersion behavior in hydrogen refueling station is carried out in this paper as well. From the results three phases of injection dispersion and buoyancy can be seen clearly. The profile of hydrogen concentration is tend to be Gaussian in dispersion region. Subsonic H2 jet in stagnant environment is calculated for refueling station the relationship between H2 concentration decay and velocity along the jet trajectory is obtained.
HyDeploy: Demonstrating Non-destructive Carbon Savings Through Hydrogen Blending
Aug 2021
Publication
The project has successfully developed the safety case and delivered a hydrogen blend via the gas network into customers’ homes. The demonstration of safety for the specific network was based on robust evidence and clear operational procedures. Alongside the enabling safety case the HyDeploy project has demonstrated the first steps of hydrogen deployment are safe technically feasible and non-disruptive both for the network and domestic users.
The key outcomes of the HyDeploy project were:
The key outcomes of the HyDeploy project were:
- Successful achievement of the first regulatory approval from the HSE to operate a live gas network above the current hydrogen limit of 0.1 vol%. The approval allowed blending up to 20 vol%.
- Development of the technical and procedural precedents to generate evidence for review by the HSE which have informed subsequent safety case submissions through HyDeploy2 and the wider hydrogen safety case industry.
- The design fabrication installation and operation of the UK’s first hydrogen grid entry unit.
- Integration of novel hydrogen production and blending technologies to create the first hydrogen delivery system based on electrolytic generation into a live gas grid.
- Safe delivery of the UK’s first hydrogen blend trial to 100 homes and 30 faculty buildings. The trial delivered over 42000 cubic metres of hydrogen and abated over 27 tonnes of CO2.
- Collaboration with appliance and equipment providers to build a robust evidence base to demonstrate equipment suitability.
- Evidencing the suitability of hydrogen blends with domestic appliances as well as larger commercial appliances including catering equipment and boilers up to 600 kW.
- Evidencing the suitability of hydrogen blends with medium and low-pressure distribution systems relating to key performance metrics such as: pressure control; odour intensity and uniform gas compositions.
- Promotion of supply chain innovation through facilitating trials to develop gas detection and analysis technologies.
- Establishing a robust social science evidence base to understand the attitudes and experience of consumers actually using hydrogen blends.
Electric and Hydrogen Rail: Potential Contribution to Net Zero in the UK
Sep 2020
Publication
Electric trains (ET) and hydrogen trains (HT) are considered zero emission at the point of use. True emissions are dependent upon non-tailpipe sources primarily in energy production. We present UK carbon dioxide (CO2) operating emission model outputs for conventionally fuelled trains (CFT) ETs and HTs between 2017 and 2050 under four National Grid electricity generation scenarios.
Comparing four service categories (urban regional intercity and high speed) to private conventionally fuelled vehicles (CFV) and electric vehicles considering average distance travelled per trip under different passenger capacity levels (125% 100% 75% 50% and 25%).
Results indicate by 2050 at 100% capacity CFTs produce a fifth of the emissions of CFVs per kilometre per person. Under two degree generation scenario by 2050 ETs produced 14 times and HTs produced five times less emissions than CFTs. Policymakers should encourage shifts away from private vehicles to public transport powered by low carbon electricity.
Comparing four service categories (urban regional intercity and high speed) to private conventionally fuelled vehicles (CFV) and electric vehicles considering average distance travelled per trip under different passenger capacity levels (125% 100% 75% 50% and 25%).
Results indicate by 2050 at 100% capacity CFTs produce a fifth of the emissions of CFVs per kilometre per person. Under two degree generation scenario by 2050 ETs produced 14 times and HTs produced five times less emissions than CFTs. Policymakers should encourage shifts away from private vehicles to public transport powered by low carbon electricity.
Hydrogen as Energy Sources—Basic Concepts
Sep 2021
Publication
This paper covers the hydrogen technologies regarding the role of hydrogen as an energy carrier and the possibilities of its production and use. It is initially presented the modalities and the efficiency of the current technologies of obtaining hydrogen detailing its obtaining by the electrolysis of the water the electrochemical efficiency and the specific consumption of electricity as well as the thermodynamics of the electrochemical processes. The following paragraph addresses hydrogen conversion possibilities. This paragraph details the thermodynamic analysis of the fuel cell the external characteristic of the fuel cell and the types of fuel cell. The last paragraph addresses the possibilities of using the fuel cells for electrical vehicles and cogeneration systems for buildings.In this context the traditional transport and distribution grid will have to adapt to the new realities as they will need to actively participate in the internal energy market by the transformation of the traditional electricity grid in energy flow from unidirectional to bidirectional through the production of hydrogen offering the same facilities as the gas grid.
Risk Assessment of a Gaseous Hydrogen Fueling Station (GHFs)
Sep 2021
Publication
Promoted by national and European investment plans promoting the use of hydrogen as energy carrier the number of Gaseous Hydrogen Fueling Station (or GHFS) has been growing up quite significantly over the past years. Considering the new possible hazards and the related accidents induced by these installations like seen in 2019 in Norway this paper presents a risk assessment of a typical GHFS using the same methodology as the one required in France by the authorities for Seveso facilities. The fact that a hydrogen fueling station could be used by a public not particularly trained to handle hydrogen underlines the importance of this risk assessment. In this article typical components related to GHFS (dispenser high pressure storage compressor low pressure storage) are listed and the hazard potentials linked to these components and the substances involved are identified. Based on these elements and an accidentology a risk analysis has been conducted in order to identify all accidental situations that could occur. The workflow included a detailed risk assessment consisting in modeling the thermal and explosion effects of all hazardous phenomena and in assessing the probability of occurrence for these scenarios. Regarding possible mitigation measures the study was based on an international benchmark for codes and standards made for GFHS. These preliminary outcomes of this study may be useful for any designer and/or owner of a GFHS.
A Review of Hydrogen as a Fuel in Internal Combustion Engines
Sep 2021
Publication
The demand for fossil fuels is increasing because of globalization and rising energy demands. As a result many nations are exploring alternative energy sources and hydrogen is an efficient and practical alternative fuel. In the transportation industry the development of hydrogen-powered cars aims to maximize fuel efficiency and significantly reduce exhaust gas emission and concentration. The impact of using hydrogen as a supplementary fuel for spark ignition (SI) and compression ignition (CI) engines on engine performance and gas emissions was investigated in this study. By adding hydrogen as a fuel in internal combustion engines the torque power and brake thermal efficiency of the engines decrease while their brake-specific fuel consumption increase. This study suggests that using hydrogen will reduce the emissions of CO UHC CO2 and soot; however NOx emission is expected to increase. Due to the reduction of environmental pollutants for most engines and the related environmental benefits hydrogen fuel is a clean and sustainable energy source and its use should be expanded.
North East Network & Industrial Cluster Development – Summary Report A Consolidated Summary Report by SGN & Wood
Nov 2021
Publication
In response to the global climate emergency governments across the world are aiming to lower greenhouse gas emissions to slow the damaging effects of climate change.<br/>The Scottish Government has set a target of net zero emissions by 2045. Already a global leader in renewable energy and low-carbon technology deployment Scotland’s energy landscape is set to undergo more change as it moves toward becoming carbon-neutral. Key to that change will be the transition from natural gas to zero-carbon gases like hydrogen and biomethane.<br/>Scotland’s north-east and central belt are home to some of its largest industrial carbon emitters. The sector’s reliance on natural gas means that it emits 11.9Mt of CO2 emissions per year says NECCUS: the equivalent of 2.6 million cars or roughly all the cars in Scotland. Most homes and businesses across Scotland also use natural gas for heating.<br/>Our North-East Network and Industrial Cluster project is laying the foundations for the rapid decarbonisation of this high-emitting sector. We’ve published a report outlining the practical steps needed to rapidly decarbonise a significant part of Scotland’s homes and industry. It demonstrates how hydrogen can play a leading role in delivering the Scottish Government’s target of one million homes with low carbon heat by 2030.<br/>The research published with global consulting and engineering advisor Wood sets out a transformational and accelerated pathway to 100% hydrogen for Scotland’s gas networks which you can see on the map below. It also details the feasibility of a CO2 collection network to securely capture transport and store carbon dioxide emissions deep underground.
Everything About Hydrogen Podcast: Why Generate Capital is Excited About the Prospects of Hydrogen
Dec 2019
Publication
On this weeks episode the team are talking all things hydrogen with Jigar Shah the President of Generate Capital and Co-host of the Energy Gang podcast. Jigar Shah has a well earned reputation as one of the most influential voices in the US clean energy market having pioneered no-money down solar with SunEdison and led the not for profit climate group the Carbon War Room. Since its founding in 2014 Generate Capital the company has provided $130 million of funds to a leading fuel cell provide Plug Power meanwhile in October 2019 Jigar declared hydrogen to be the ultimate clean electricity enabler. On the show we ask Jigar why he thinks Hydrogen is becoming interesting for investors today what business models he feels are exciting and offer the most attractive niches for hydrogen technology businesses whilst getting his side of the story on that time he met Chris at a conference…..All this and more on the show!
The podcast can be found on their website
The podcast can be found on their website
Prospective Techno-economic and Environmental Assessment of a National Hydrogen Production Mix for Road Transport
Nov 2019
Publication
Fuel cell electric vehicles arise as an alternative to conventional vehicles in the road transport sector. They could contribute to decarbonising the transport system because they have no direct CO2 emissions during the use phase. In fact the life-cycle environmental performance of hydrogen as a transportation fuel focuses on its production. In this sense through the case study of Spain this article prospectively assesses the techno-economic and environmental performance of a national hydrogen production mix by following a methodological framework based on energy systems modelling enriched with endogenous carbon footprint indicators. Taking into account the need for a hydrogen economy based on clean options alternative scenarios characterised by carbon footprint restrictions with respect to a fossil-based scenario dominated by steam methane reforming are evaluated. In these scenarios the steam reforming of natural gas still arises as the key hydrogen production technology in the short term whereas water electrolysis is the main technology in the medium and long term. Furthermore in scenarios with very restrictive carbon footprint limits biomass gasification also appears as a key hydrogen production technology in the long term. In the alternative scenarios assessed the functional substitution of hydrogen for conventional fossil fuels in the road transport sector could lead to high greenhouse gas emission savings ranging from 36 to 58 Mt CO2 eq in 2050. Overall these findings and the model structure and characterisation developed for the assessment of hydrogen energy scenarios are expected to be relevant not only to the specific case study of Spain but also to analysts and decision-makers in a large number of countries facing similar concerns.
Life Cycle Assessment of Hydrogen Transportation Pathways via Pipelines and Truck Trailers: Implications as a Low Carbon Fuel
Sep 2022
Publication
Hydrogen fuel cells have the potential to play a significant role in the decarbonization of the transportation sector globally and especially in California given the strong regulatory and policy focus. Nevertheless numerous questions arise regarding the environmental impact of the hydrogen supply chain. Hydrogen is usually delivered on trucks in gaseous form but can also be transported via pipelines as gas or via trucks in liquid form. This study is a comparative attributional life cycle analysis of three hydrogen production methods alongside truck and pipeline transportation in gaseous form. Impacts assessed include global warming potential (GWP) nitrogen oxide volatile organic compounds and particulate matter 2.5 (PM2.5). In terms of GWP the truck transportation pathway is more energy and ecologically intensive than pipeline transportation despite gaseous truck transport being more economical. A sensitivity analysis of pipeline transportation and life cycle inventories (LCI) attribution is included. Results are compared across multiple scenarios of the production and transportation pathways to discover the strongest candidates for minimizing the environmental footprint of hydrogen production and transportation. The results indicate the less ecologically intensive pathway is solar electrolysis through pipelines. For 1 percent pipeline attribution the total CO2eq produced per consuming 1 MJ of hydrogen in a fuel cell pickup truck along this pathway is 50.29 g.
Hydrogen Production Technologies Overview
Jan 2019
Publication
Hydrogen energy became the most significant energy as the current demand gradually starts to increase. Hydrogen energy is an important key solution to tackle the global temperature rise. The key important factor of hydrogen production is the hydrogen economy. Hydrogen production technologies are commercially available while some of these technologies are still under development. This paper reviews the hydrogen production technologies from both fossil and non-fossil fuels such as (steam reforming partial oxidation auto thermal pyrolysis and plasma technology). Additionally water electrolysis technology was reviewed. Water electrolysis can be combined with the renewable energy to get eco-friendly technology. Currently the maximum hydrogen fuel productions were registered from the steam reforming gasification and partial oxidation technologies using fossil fuels. These technologies have different challenges such as the total energy consumption and carbon emissions to the environment are still too high. A novel non-fossil fuel method [ammonia NH3] for hydrogen production using plasma technology was reviewed. Ammonia decomposition using plasma technology without and with a catalyst to produce pure hydrogen was considered as compared case studies. It was showed that the efficiency of ammonia decomposition using the catalyst was higher than ammonia decomposition without the catalyst. The maximum hydrogen energy efficiency obtained from the developed ammonia decomposition system was 28.3% with a hydrogen purity of 99.99%. The development of ammonia decomposition processes is continues for hydrogen production and it will likely become commercial and be used as a pure hydrogen energy source.
Everything About Hydrogen Podcast: Scaling Clean Hydrogen Production
Dec 2021
Publication
Today we are joined by our good friends from Enapter. The company is a leader in the clean hydrogen sector focused on AEM electrolyzer technology and innovative software solutions that make it possible to rapidly deploy and scale hydrogen production assets. For those who follow the hydrogen sector regularly it’s been hard not to hear Enapter-related news in 2021 and its impressive trajectory as they have gone public announced the plans for a brand new production facility in Germany (on which they have now begun construction) and most recently the announcement that Enapter was selected as the winner of the prestigious Earthshot prize. To do that we are absolutely delighted to have with us all the way from his home base in Thailand Thomas Chrometzka Chief Strategy Officer at Enapter and one of the people that we enjoy having on the show so much that we have brought him back again to fill us in on what he and Enapter are up to and what they have planned for the future of hydrogen.
The podcast can be found on their website
The podcast can be found on their website
Well to Wheel Analysis of Low Carbon Alternatives for Road Traffic
Sep 2015
Publication
Several alternative fuel–vehicle combinations are being considered for replacement of the internal combustion engine (ICE) vehicles to reduce greenhouse gas (GHG) emissions and the dependence on fossil fuels. The International Energy Agency has proposed the inclusion of low carbon alternatives such as electricity hydrogen and biofuels in the transport sector for reducing the GHG emissions and providing a sustainable future. This paper compares the use of these alternative fuels viz. electricity hydrogen and bio-ethanol in combination with battery electric vehicle (BEV) and fuel cell electric vehicle (FCEV) technologies on the basis of their overall efficiency and GHG emissions involved in the conversion of the primary energy source to the actual energy required at wheels through a well-to-wheel analysis. The source of energy for electricity production plays a major role in determining the overall efficiency and the GHG emissions of a BEV. Hence electricity production mix of Germany (60% fossil fuel energy) France (76% nuclear energy) Sweden and Austria (60 and 76% renewable energy respectively) the European Union mix (48% fossil fuel energy) and the United States of America (68% fossil fuel energy) are considered for the BEV analysis. In addition to the standard hydrogen based FCEVs CNG and bio-ethanol based FCEVs are analysed. The influence of a direct ethanol fuel cell (DEFC) on GHG emissions and overall chain efficiency is discussed. In addition to the standard sources of bio-ethanol (like sugarcane corn etc.) sources like wood waste and wheat straw are included in the analysis. The results of this study suggest that a BEV powered by an electricity production mix dominated by renewable energy and bio-ethanol based DEFC electric vehicles offer the best solution in terms of GHG emissions efficiency and fossil fuel dependency. Bio-ethanol as a fuel has the additional advantage to be implemented readily in ICE vehicles followed by advancements through reformer based FCEVs and DEFC electric vehicles. Although important this analysis does not include the health effects of the alternative vehicles. Bio-ethanol used in an ICE may lead to increased emission of acetaldehydes which however might not be the case if it is used in fuel cells.
Developing Networks for the Future: Long-Term Development Plan 2019
Oct 2019
Publication
This report provides you with the information you need if you have plans to interact with or connect to our gas networks. Our vision is to set the standards that all of our customers love and others aspire to. This means that our long-term plans are shaped by our customers and stakeholders. This annual publication is an important opportunity to share our latest long-term plan and our strategic thinking and seek feedback so we can continue to adapt our activities going forward. We want to make it as easy and efficient as possible for you to interact with us.
Cadent Long Term Development Plan 2019
Cadent Long Term Development Plan 2019
Evaluation of Performance Characteristics of a Novel Hydrogen-fuelled Free-piston Engine Generator
Mar 2020
Publication
In this work we present the experimental results obtained from hydrogen fuelled spark-ignited dual piston free-piston engine generator (FPEG) prototype operated in two-stroke and four-stroke mode. The FPEG testing was successfully conducted at 3.7 compression ratio engine speed between 5 Hz and 11 Hz and with different equivalence ratios. The FPEG technical details experimental set-up and operational control are explained in detail. Performance indicators show that both equivalence ratio and engine speed affect the engine operation characteristics. For every set of specified FPEG parameters appropriate range of equivalence ratio is recommended to prevent unwanted disturbance to electric generator operation. Both two-stroke and four-stroke cycle mode were tested and the results showed different combustion characteristics with the two thermodynamic cycles. Four-stroke cycle mode could operate with indicated thermal efficiency gain up to 13.2% compared with the two-stroke cycle.
Numerical Simulation of Hydrogen Leakage and Diffusion Process of Fuel Cell Vehicle
Oct 2021
Publication
Regarding the problem of hydrogen diffusion of the fuel cell vehicle (HFCV) when its hydrogen supply system leaks this research uses the FLUENT software to simulate numerical values in the process of hydrogen leakage diffusion in both open space and closed space. This paper analyzed the distribution range and concentration distribution characteristics of hydrogen in these two different spaces. Besides this paper also took a survey about the effects of leakage rate wind speed wind direction in open space and the role the air vents play on hydrogen safety in closed space which provides a reference for the hydrogen safety of HFCV. In conclusion the experiment result showed that: In open space hydrogen leakage rate has a great influence on its diffusion. When the leakage rate doubles the hydrogen leakage range will expand about 1.5 times simultaneously. The hydrogen diffusion range is the smallest when the wind blows at 90 degrees which is more conducive to hydrogen diffusion. However when the wind direction is against the direction of the leakage of hydrogen the range of hydrogen distribution is maximal. Under this condition the risk of hydrogen leakage is highest. In an enclosed space when the vent is set closest to the leakage position the volume fraction of hydrogen at each time is smaller than that at other positions so it is more beneficial to safety.
Quantification of Hydrogen in Nanostructured Hydrogenated Passivating Contacts for Silicon Photovoltaics Combining SIMS-APT-TEM: A Multiscale Correlative Approach
Mar 2021
Publication
Multiscale characterization of the hydrogenation process of silicon solar cell contacts based on c-Si/SiOx/nc-SiCx(p) has been performed by combining dynamic secondary ion mass-spectrometry (D-SIMS) atom probe tomography (APT) and transmission electron microscopy (TEM). These contacts are formed by high-temperature firing which triggers the crystallization of SiCx followed by a hydrogenation process to passivate remaining interfacial defects. Due to the difficulty of characterizing hydrogen at the nm-scale the exact hydrogenation mechanisms have remained elusive. Using a correlative TEM-SIMS-APT analysis we are able to locate hydrogen trap sites and quantify the hydrogen content. Deuterium (D) a heavier isotope of hydrogen is used to distinguish hydrogen introduced during hydrogenation from its background signal. D-SIMS is used due to its high sensitivity to get an accurate deuterium-to-hydrogen ratio which is then used to correct deuterium profiles extracted from APT reconstructions. This new methodology to quantify the concentration of trapped hydrogen in nm-scale structures sheds new insights on hydrogen distribution in technologically important photovoltaic materials.
Internal Film Cooling with Discrete-Slot Injection Orifices in Hydrogen/Oxygen Engine Thrust Chambers
May 2022
Publication
In the present study a hydrogen and oxygen heat-sink engine thrust chamber and the corresponding injection faceplate with discrete slot orifices are devised to study the cooling performance near the faceplate region. Moreover a set of experiments and numerical simulations are conducted to evaluate the effects of various factors on combustion performance and film cooling efficiency. According to the obtained result the circumferential cooling efficiency has an M-shaped distribution in the near-injector region. Furthermore it has been discovered that when the film flow ratio increases so does the cooling efficiency. This is especially more pronounced in the range of 30–80 mm from the faceplate. The cooling efficiency is found to be proportional to the film flow rate ratio’s 0.4 power. Compared with the slot thickness the reduction in the slot width is more beneficial in improving the cooling efficiency and the advantage is more prominent for small film flow ratios. In addition when the amount of coolant is not enough the cooling effect of the discrete slot film orifice is better than that of the common cylindrical orifice. The present article demonstrates that setting the area ratio of the adjacent film orifices is an effective way to reduce the uneven circumferential distribution of the wall surface temperature.
Flow of Hydrogen from Buried Leaks
Sep 2019
Publication
The substitution of hydrogen for natural gas within a gas network has implications for the potential rate of leakage from pipes and the distribution of gas flow driven by such leaks. This paper presents theoretical analyses of low-pressure flow through porous ground in a range of circumstances and practical experimental work at a realistic scale using natural gas hydrogen or nitrogen for selected cases. This study considers flow and distribution of 100% hydrogen. A series of eight generic flow regimes have been analysed theoretically e.g. (i) a crack in uncovered ground (ii) a crack under a semi-permeable cover in a high porosity channel (along a service line or road). In all cases the analyses yield both the change in flow rate when hydrogen leaks and the change in distance to which hydrogen gas can travel at a dangerous rate compared to natural gas. In some scenarios a change to hydrogen gas from natural gas makes minimal difference to the range (i.e. distance from the leak) at which significant gas flows will occur. However in cases where the leak is covered by an impermeable membrane a change to hydrogen from natural gas may extend the range of significant gas flow by tens or even hundreds of metres above that of natural gas. Experimental work has been undertaken in specific cases to investigate the following: (i) Flow rate vs pressure curves for leaks into media with different permeability (ii) Effects of the water content of the ground on gas flow (iii) Distribution of surface gas flux near a buried leak
Hydrogen Supply Chains for Mobility—Environmental and Economic Assessment
May 2018
Publication
Hydrogen mobility is one option for reducing local emissions avoiding greenhouse gas (GHG) emissions and moving away from a mainly oil-based transport system towards a diversification of energy sources. As hydrogen production can be based on a broad variety of technologies already existing or under development a comprehensive assessment of the different supply chains is necessary regarding not only costs but also diverse environmental impacts. Therefore in this paper a broad variety of hydrogen production technologies using different energy sources renewable and fossil are exemplarily assessed with the help of a Life Cycle Assessment and a cost assessment for Germany. As environmental impacts along with the impact category Climate change five more advanced impact categories are assessed. The results show that from an environmental point of view PEM and alkaline electrolysis are characterized by the lowest results in five out of six impact categories. Supply chains using fossil fuels in contrast have the lowest supply costs; this is true e.g. for steam methane reforming. Solar powered hydrogen production shows low impacts during hydrogen production but high impacts for transport and distribution to Germany. There is no single supply chain that is the most promising for every aspect assessed here. Either costs have to be lowered further or supply chains with selected environmental impacts have to be modified.
Microalgal Hydrogen Production in Relation to Other Biomass‐Based Technologies—A Review
Sep 2021
Publication
Hydrogen is an environmentally friendly biofuel which if widely used could reduce atmospheric carbon dioxide emissions. The main barrier to the widespread use of hydrogen for power generation is the lack of technologically feasible and—more importantly—cost‐effective methods of production and storage. So far hydrogen has been produced using thermochemical methods (such as gasification pyrolysis or water electrolysis) and biological methods (most of which involve anaerobic digestion and photofermentation) with conventional fuels waste or dedicated crop biomass used as a feedstock. Microalgae possess very high photosynthetic efficiency can rapidly build biomass and possess other beneficial properties which is why they are considered to be one of the strongest contenders among biohydrogen production technologies. This review gives an account of present knowledge on microalgal hydrogen production and compares it with the other available biofuel production technologies.
Research and Development Investment and Collaboration Framework for the Hydrogen Economy in South Korea
Sep 2021
Publication
South Korea developed its hydrogen strategies to achieve carbon neutrality and dominate the hydrogen economy amidst and with the impetus of the coronavirus disease 2019 (COVID-19) pandemic. The government strives toward the goal via continuous investment in green hydrogen technologies as well as strategic collaborations. To facilitate the transition into the hydrogen economy this study presents a research and development (R&D) investment and collaboration framework as a national strategy. The framework offers abundant information to elucidate the technology R&D spectrum and regional dimensions of the strategy. Furthermore the proposed framework was applied to the Korean hydrogen economy comprising 955 nationally funded projects worth USD 565.7 million. The statuses and trends of the government’s investment in nationally funded research projects are illustrated with regard to the value chains of the hydrogen economies of 16 regions as well as nine technology clusters relating to the hydrogen economy thereby determining the research organizations that played crucial roles in each cluster of the 16 regions between 2015 and 2020. The results indicate that the research organizations in Daejeon acquired the highest government R&D funding in many hydrogen-economy-related research fields and that an R&D spectrum-based research/strategic collaboration is required to accomplish specialized complexes in the regions.
Green Hydrogen Storage in an Underground Cavern: A Case Study in Salt Diapir of Spain
Jun 2022
Publication
The Poza de la Sal diapir is a closed circular depression with Cretaceous Mesozoic materials formed by gypsum Keuper clays and a large extension of salt in the center with intercalations of ophite. The low seismic activity of the area the reduced permeability and porosity of the salt caverns and the proximity to the Páramo de Poza wind park make it a suitable place for the construction of a facility for underground storage of green hydrogen obtained from surplus wind power. The design of a cavern for hydrogen storage at a depth of 1000 m takes into account the differences in stresses temperatures and confining pressures involved in the salt deformation process. During the 8 months of the injection phase 23.0 GWh can be stored in the form of hydrogen obtained from the wind energy surplus to be used later in the extraction phase. The injection and extraction ratio must be developed under the conditions of geomechanical safety of the cavity so as to minimize the risks to the environment and people by conditioning the gas pressure inside the cavity to remain within a given range.
Total Cost of Ownership and Its Potential Consequences for the Development of the Hydrogen Fuel Cell Powered Vehicle Market in Poland
Apr 2021
Publication
Electromobility is a growing technology for land transport constituting an important element of the concept of sustainable economic development. The article presents selected research results concerning one of the segments of this market-vehicles powered by hydrogen fuel cells. The subject of the research was to gain extensive knowledge on the economic factors influencing the future purchasing decisions of the demand side in relation to this category of vehicles. The research was based on a numerical experiment. For this purpose a comparative analysis of purchase prices in relation to the TCO of the vehicle after 3–5 years of use was performed. The research included selected models that are powered by both conventional and alternative fuels. The use of this method will allow to assess the real costs associated with the hydrogen vehicle. The authors emphasize the important role of economic factors in the form of the TCO index for the development of this market. The experimental approach may be helpful in understanding the essence of economic relations that affect the development of the electro-mobility market and the market demand for hydrogen fuel cell-powered vehicles in Poland.
Wettability of Shale–brine–H2 System and H2-brine Interfacial Tension for Assessment of the Sealing Capacities of Shale Formations During Underground Hydrogen Storage
Jul 2022
Publication
Replacement of fossil fuels with clean hydrogen has been recognized as the most feasible approach of implementing CO2-free hydrogen economy globally. However large-scale storage of hydrogen is a critical component of hydrogen economy value chain because hydrogen is the lightest molecule and has moderately low volumetric energy content. To achieve successful storage of buoyant hydrogen at the subsurface and convenient withdrawal during the period of critical energy demand the integrity of the underground storage rock and overlying seal (caprock) must be assured. Presently there is paucity of information on hydrogen wettability of shale and the interfacial properties of H2/brine system. In this research contact angles of shale/H2/brine system and hydrogen/brine interfacial tension (IFT) were measured using Krüss drop shape analyzer (DSA 100) at 50 ◦C and varying pressure (14.7–1000 psi). A modified form of sessile drop approach was used for the contact angles measurement whereas the H2- brine IFT was measured through the pendant drop method. H2-brine IFT values decreased slightly with increasing pressure ranging between 63.68◦ at 14.7 psia and 51.29◦ at 1000 psia. The Eagle-ford shale with moderate total organic carbon (TOC) of 3.83% attained fully hydrogen-wet (contact angle of 99.9◦ ) and intermediate-wet condition (contact angle of 89.7◦ ) at 14.7 psi and 200 psi respectively. Likewise the Wolf-camp shale with low TOC (0.30%) attained weakly water-wet conditions with contact angles of 58.8◦ and 62.9◦ at 14.7 psi and 200 psi respectively. The maximum height of hydrogen that can be securely trapped by the Wolf-camp shale was approximately 325 meters whereas the value was merely 100 meters for the Eagle-ford shale. Results of this study will aid in assessment of hydrogen storage capacity of organic-rich shale (adsorption trapping) as well as evaluation of the sealing potentials of low TOC shale (caprock) during underground hydrogen storage.
1921–2021: A Century of Renewable Ammonia Synthesis
Apr 2022
Publication
Synthetic ammonia manufactured by the Haber–Bosch process and its variants is the key to securing global food security. Hydrogen is the most important feedstock for all synthetic ammonia processes. Renewable ammonia production relies on hydrogen generated by water electrolysis using electricity generated from hydropower. This was used commercially as early as 1921. In the present work we discuss how renewable ammonia production subsequently emerged in those countries endowed with abundant hydropower and in particular in regions with limited or no oil gas and coal deposits. Thus renewable ammonia played an important role in national food security for countries without fossil fuel resources until after the mid-20th century. For economic reasons renewable ammonia production declined from the 1960s onward in favor of fossil-based ammonia production. However renewable ammonia has recently gained traction again as an energy vector. It is an important component of the rapidly emerging hydrogen economy. Renewable ammonia will probably play a significant role in maintaining national and global energy and food security during the 21st century.
Power-to-Gas and Power-to-X—The History and Results of Developing a New Storage Concept
Oct 2021
Publication
Germany’s energy transition known as ‘Energiewende’ was always very progressive. However it came technically to a halt at the question of large-scale seasonal energy storage for wind and solar which was not available. At the end of the 2000s we combined our knowledge of both electrical and process engineering imitated nature by copying photosynthesis and developed Power-to-Gas by combining water electrolysis with CO2 -methanation to convert water and CO2 together with wind and solar power to synthetic natural gas. Storing green energy by coupling the electricity with the gas sector using its vast TWh-scale storage facility was the solution for the biggest energy problem of our time. This was the first concept that created the term ‘sector coupling’ or ‘sectoral integration’. We first implemented demo sites presented our work in research industry and ministries and applied it in many macroeconomic studies. It was an initial idea that inspired others to rethink electricity as well as eFuels as an energy source and energy carrier. We developed the concept further to include Power-to-Liquid Power-to-Chemicals and other ways to ‘convert’ electricity into molecules and climate-neutral feedstocks and named it ‘Power-to-X’ at the beginning of the 2010s.
Response Time Measurement of Hydrogen Sensors
Sep 2017
Publication
The efficiency of gas sensor application for facilitating the safe use of hydrogen depends considerably on the sensor response to a change in hydrogen concentration. Therefore the response time has been measured for five different-type commercially available hydrogen sensors. Experiments showed that all these sensors surpass the ISO 26142 standard; for the response times t90 values of 2 s to 16 s were estimated. Results can be fitted with an exponential or sigmoidal function. It can be demonstrated that the results on transient behaviour depend on both the operating parameters of sensors and investigation methods as well as on the experimental conditions: gas change rate and concentration jump.
In Situ Neutron Radiography Investigations of Hydrogen Related Processes in Zirconium Alloys
Jun 2021
Publication
In situ neutron radiography experiments can provide information about diffusive processes and the kinetics of chemical reactions. The paper discusses requirements for such investigations. As examples of the zirconium alloy Zircaloy-4 the hydrogen diffusion the hydrogen uptake during high-temperature oxidation in steam and the reaction in nitrogen/steam and air/steam atmospheres results of in situ neutron radiography investigations are reviewed and their benefit is discussed.
Demonstration of a kW-scale Solid Oxide Fuel Cell-calciner for Power Generation and Production of Calcined Materials
Aug 2019
Publication
Carbonate looping (CaL) has been shown to be less energy-intensive when compared to mature carbon capture technologies. Further reduction in the efficiency penalties can be achieved by employing a more efficient source of heat for the calcination process instead of oxy-fuel combustion. In this study a kW-scale solid oxide fuel cell (SOFC)-integrated calciner was designed and developed to evaluate the technical feasibility of simultaneously generating power and driving the calcination process using the high-grade heat of the anode off-gas. Such a system can be integrated with CaL systems or employed as a negative-emission technology where the calcines are used to capture CO2 from the atmosphere. The demonstration unit consisted of a planar SOFC stack operating at 750 °C and a combined afterburner/calciner to combust hydrogen slip from the anode off-gas and thermally decompose magnesite dolomite and limestone. The demonstrator generated up to 2 kWelDC power achieved a temperature in the range of 530–550 °C at the inlet of the afterburner and up to 678 °C in the calciner which was sufficient to demonstrate full calcination of magnesite and partial calcination of dolomite. However in order to achieve the temperature required for calcination of limestone further scale-up and heat integration are needed. These results confirmed technical feasibility of the SOFC-calciner concept for production of calcined materials either for the market or for direct air capture (DAC).
Everything About Hydrogen Podcast: Commercial Trucking at the Speed of Hydrogen
Jun 2021
Publication
The transportation and mobility sector is vast complex unwieldy and most excitingly an obvious area of focus for hydrogen fuel cell technology applications. Hydrogen FCEVs allow vehicles to run in a wide range of environments with zero tailpipe emissions and can do so without the need for extremely heavy battery cells and can be refueled in the same amount of time as a modern ICE vehicle. This makes hydrogen FCEVs an ideal fit for the heavy commercial transportation industry and is why Hyzon Motors has jumped at the opportunity to revolutionize the industry. The company has grabbed headlines all over the world with its ambitious plans for rolling out its trucks in the United States and other major markets. It has also made news with its recent announcement that the company is going public and has attracted significant investor interest. The EAH team is joined on this episode by Hyzon's CEO Craig Knight to talk about how the company is tackling some of the most significant challenges in decarbonizing transport and how it can make trucking a zero-emission operation.
The podcast can be found on their website
The podcast can be found on their website
Experimental Investigation on the Burning Behavior of Homogenous H2-CO-Air Mixtures in an Obstructed Semi-confined Channel
Sep 2021
Publication
In the current work the combustion behavior of hydrogen-carbon monoxide-air mixtures in semiconfined geometries is investigated in a large horizontal channel facility (dimensions 9 m x 3 m x 0.6 m (L x W x H)) as a part of a joint German nuclear safety project. In the channel with evenly distributed obstacles (blockage ratio 50%) and an open to air ground face homogeneous H2-CO-air mixtures are ignited at one end. The combustion behavior of the mixture is analyzed using the signals of pressure sensors modified thermocouples and ionization probes for flame front detection that are distributed along the channel ceiling. In the experiments various fuel concentrations (cH2 + cCO = 14 to 22 Vol%) with different H2:CO ratios (75:25 50:50 and 25:75) are used and the transition regions for a significant flame acceleration to sonic speed (FA) as well as to a detonation (DDT) are investigated. The conditions for the onset of these transitions are compared with earlier experiments performed in the same facility with H2-air mixtures. The results of this work will help to allow a more realistic estimation of the pressure loads generated by the combustion of H2-CO-air mixtures in obstructed semi-confined geometries.
Investigation on the Effects of Blending Hydrogen-rich Gas in the Spark-ignition Engine
May 2022
Publication
In order to improve the energy efficiency of the internal combustion engine and replace fossil fuel with alternative fuels a concept of the methanol-syngas engine was proposed and the prototype was developed. Gasoline and dissociated methanol gas (GDM) were used as dual fuels and the engine performance was investigated by simulation and experiments. Dissociated methanol gas is produced by recycling the exhaust heat. The performance and combustion process was studied and compared with the gasoline engine counterpart. There is 1.9% energy efficiency improvement and 5.5% fuel consumption reduction under 2000r/min 100 N · m working condition with methanol substitution ratio of 10%. In addition the engine efficiency further improves with an increase of dissociated methanol gas substitution ratio because of the increased heating value of the fuel and effects of hydrogen. The peak pressure in the cylinder and the peak heat release rate of the GDM engine are higher than that of the original gasoline engine with a phase closer to the top dead center (TDC). Therefore blending hydrogen-rich gas in the spark-ignition engine can recycle the exhaust heat and improve the thermal efficiency of the engine.
Fugitive Hydrogen Emissions in a Future Hydrogen Economy
Apr 2022
Publication
There is an increasing body of evidence that leakage of hydrogen to the atmosphere will have an indirect warming effect on the climate and so should be minimised.<br/>This study investigates and quantifies the current understanding of potential hydrogen emissions in the different sectors across a future hydrogen value-chain. It shows that there are some key areas in production distribution and end-use where there could potentially be significant leaks of hydrogen to the atmosphere. In some of these areas there are clear mitigation options while with others the options are less clear due to uncertainty in either data or future technology development.<br/>The report recommends further research and development to reduce the main leak pathways and additional evidence gathering in key areas where there is currently inadequate data to make accurate predictions.<br/>The study was commissioned by BEIS and conducted by the Frazer-Nash consultancy.
Remarkable Visible-light Induced Hydrogen Generation with ZnIn2S4 Microspheres/CuInS2 Quantum Dots Photocatalytic System
Oct 2020
Publication
A new and active material in the form of ZnIn2S4 microspheres decorated by CuInS2 quantum dots have been obtained by hydrothermal method for the first time. The optimum amount of CuInS2 quantum dots (1.13 wt.%) introduced into rection medium during ZnIn2S4 microspheres synthesis increased the photocatalytic H2 generation rate by 2.5 times than that of bare ZnIn2S4 photocatalysis under visible light irradiation. This sample exhibited strong photoactivity in the extended visible range up to 540 nm with 30.6% apparent quantum efficiency (λ = 420 nm).
Detection of Contaminants in Hydrogen Fuel for Fuel Cell Electrical Vehicles with Sensors—Available Technology, Testing Protocols and Implementation Challenges
Dec 2021
Publication
Europe’s low-carbon energy policy favors a greater use of fuel cells and technologies based on hydrogen used as a fuel. Hydrogen delivered at the hydrogen refueling station must be compliant with requirements stated in different standards. Currently the quality control process is performed by offline analysis of the hydrogen fuel. It is however beneficial to continuously monitor at least some of the contaminants onsite using chemical sensors. For hydrogen quality control with regard to contaminants high sensitivity integration parameters and low cost are the most important requirements. In this study we have reviewed the existing sensor technologies to detect contaminants in hydrogen then discussed the implementation of sensors at a hydrogen refueling stations described the state-of-art in protocols to perform assessment of these sensor technologies and finally identified the gaps and needs in these areas. It was clear that sensors are not yet commercially available for all gaseous contaminants mentioned in ISO14687:2019. The development of standardized testing protocols is required to go hand in hand with the development of chemical sensors for this application following a similar approach to the one undertaken for air sensors.
Electric Load Influence on Performances of a Composite Plant for Hydrogen Production from RES and its Conversion in Electricity
Nov 2019
Publication
The analysis here presented investigates the influence of electrical load on the operational performances of a plant for hydrogen production from solar energy and its conversion in electricity via a fuel cell. The plant is an actual one currently under construction in Reggio Calabria (Italy) at the site of the Mediterranean university campus; it is composed of a Renewable Energy Source (RES) section (photovoltaic panels) a hydrogen production section and a fuel cell power section feeding the electrical energy demand of the load. Two different load configurations have been analysed and simulations have been carried out through HomerTM simulation code. Results allow interesting conclusions regarding the plant operation to be drawn. The study could have a remarkable role in supporting further research activities aimed at the assessment of the optimal configuration of this type of pioneering plants designed for feeding electrical loads possibly in a self-sufficient way.
An Ammonia-Hydrogen Energy Roadmap for Carbon Neutrality: Opportunity and Challenges in China
Nov 2021
Publication
China has promised to reach the peak carbon dioxide emission (ca. 10 billion tons) by 2030 and carbon neutrality by 2060. To realize these goals it is necessary to develop hydrogen energy and fuel cell techniques. However the high cost and low intrinsic safety of high-pressure hydrogen storage limit their commercialization. NH3 is high in hydrogen content easily liquefied at low pressure and free of carbon and the technology of NH3 synthesis has been commercialized nationwide. It is worth noting that the production of NH3 in China is about 56 million tons per year accounting for 35% of worldwide production. Hence with the well established infrastructure for NH3 synthesis and transportation and the demand for clean energy in China it is feasible to develop a green and economical energy roadmap viz. “Clean low-pressure NH3 synthesis → Safe and economical NH3 storage and transportation → Carbon-free efficient NH3-H2 utilization” for low-carbon or even carbon-free energy production.<br/>Currently the academic and industrial communities in China are striving to make technological breakthroughs in areas such as photocatalytic water splitting electrocatalytic water splitting mild-condition NH3 synthesis low-temperature NH3 catalytic decomposition and indirect or direct NH3 fuel cells with significant progress.<br/>Taking full advantage of the NH3 synthesis industry and readjusting the industrial structure it is viable to achieve energy saving and emission reduction in NH3 synthesis industry (440 million tons CO2 per year) as well as promote a new energy industry and ensure national energy security. Therefore relevant academic and industrial communities should put effort on mastering the key technologies of “Ammonia-Hydrogen” energy conversion and utilization with complete self-dependent intellectual property. It is envisioned that through the establishment of “Renewable Energy-Ammonia-Hydrogen” circular economy a green technology chain for hydrogen energy industry would pose as a promising pathway to achieve the 2030 and 2060 goals.
Numerical Study of the Action of Convection on the Volume and Length of the Flammable Zone Formed by Hydrogen Emissions from the Vent Masts Installed on an International Ship
Nov 2021
Publication
International ships carrying liquefied fuel are strongly recommended to install vent masts to control the pressure of cargo tanks in the event of an emergency. However the gas emitted from a vent mast may be hazardous for the crew of the ship. In the present study the volume and length of the flammable zone (FZ) created by the emitted gas above the ship was examined. Various scenarios comprising four parameters namely relative wind speed arrangement of vent masts combination of emissions among four vent masts and direction of emission from the vent-mast outlet were considered. The results showed that the convection acts on the volume and length of an FZ. The volume of an FZ increases when there is a reduction in convection reaching the FZ and when strong convection brings hydrogen from a nearby FZ. The length of the FZ is also related to convection. An FZ is elongated if the center of a vortex is located inside the FZ because this vortex traps hydrogen inside the FZ. The length of an FZ decreases if the center of the vortex is located outside the FZ as such a vortex brings more fresh air into the FZ.
Gasification of Solid Fuels (Coal, Biomass and MSW): Overview, Challenges and Mitigation Strategies
Jun 2022
Publication
Currently hydrogen energy is the most promising energy vector while gasification is one of the major routes for its production. However gasification suffers from various issues including slower carbon conversion poor syngas quality lower heating value and higher emissions. Multiple factors affect gasification performance such as the selection of gasifiers feedstock’s physicochemical properties and operating conditions. In this review the status of gasification key gasifier technologies and the effect of solid-fuel (i.e. coal biomass and MSW) properties on gasification performance are reviewed critically. Based on the current review the co-gasification of coal biomass and solid waste along with a partial utilisation of CO2 as a reactant are suggested. Furthermore a technological breakthrough in carbon capture and sequestration is needed to make it industrially viable
Monte-Carlo-Analysis of Minimum Burst Requirements for Composite Cylinders for Hydrogen Service
Sep 2021
Publication
For achieving Net Zero-aims hydrogen is an indispensable component probably the main component. For the usage of hydrogen a wide acceptance is necessary which requires trust in hydrogen based on absence of major incidents resulting from a high safety level. Burst tests stand for a type of testing that is used in every test standard and regulation as one of the key issues for ensuring safety in use. The central role of burst and proof test is grown to historical reasons for steam engines and steel vessels but - with respect for composite pressure vessels (CPVs) - not due an extraordinary depth of outcomes. Its importance results from the relatively simple test process with relatively low costs and gets its importance by running of the different test variations in parallel. In relevant test und production standards (as e. g. ECE R134) the burst test is used in at least 4 different meanings. There is the burst test on a) new CPVs and some others b) for determining the residual strength subsequent to various simulations of ageing effects. Both are performed during the approval process on a pre-series. Then there is c) the batch testing during the CPVs production and finally d) the 100% proof testing which means to stop the burst test at a certain pressure level. These different aspects of burst tests are analysed and compared with respect to its importance for the resulting safety of the populations of CPVs in service based on experienced test results and Monte-Carlo simulations. As main criterial for this the expected failure rate in a probabilistic meaning is used. This finally ends up with recommendations for relevant RC&S especially with respect to GTR 13."
Everything About Hydrogen Podcast: Could Electrolysers Replicate Moore's Law?
Apr 2020
Publication
On this weeks episode the team are talking all things hydrogen with Sebastian-Justus Schmidt Chairman of Enapter and Thomas Chrometzka Head of Strategy at Enapter. On the show we discuss Enapter’s Anion Exchange Membrane (AEM) electrolyser and why Enapter believe that their modular electrolyser approach will revolutionise the cost of green hydrogen. We also discuss the wide array of use cases and sectors that Enapter are already working with to provide their solution as well as their view on where the current barriers exist for the hydrogen market. All this and more on the show!
The podcast can be found on their website
The podcast can be found on their website
Performance Assessment of an Integrated Environmental Control System of Civil Hypersonic Vehicles
Apr 2022
Publication
This paper discloses the architecture and related performance of an environment control system designed to be integrated within a complex multi-functional thermal and energy management system that manages the heat loads and generation of electric power in a hypersonic vehicle by benefitting from the presence of cryogenic liquid hydrogen onboard. A bleed-less architecture implementing an open-loop cycle with a boot-strap sub-freezing air cycle machine is suggested. Hydrogen boil-off reveals to be a viable cold source for the heat exchangers of the system as well as for the convective insulation layer designed around the cabin walls. Including a 2 mm boil-off convective layer into the cabin cross-section proves to be far more effective than a more traditional air convective layer of approximately 60 mm. The application to STRATOFLY MR3 a Mach 8 waverider cruiser using liquid hydrogen as propellant confirmed that presence of cryogenic tanks provides up to a 70% reduction in heat fluxes entering the cabin generated outside of it but inside the vehicle by the propulsive system and other onboard systems. The effectiveness of the architecture was confirmed for all Mach numbers (from 0.3 to 8) and all flight altitudes (from sea level to 35 km).
Dedicated Large-scale Floating Offshore Wind to Hydrogen: Assessing Design Variables in Proposed Typologies
Mar 2022
Publication
To achieve the Net-Zero Emissions goal by 2050 a major upscale in green hydrogen needs to be achieved; this will also facilitate use of renewable electricity as a source of decarbonised fuel in hard-to-abate sectors such as industry and transport. Nearly 80% of the world’s offshore wind resource is in waters deeper than 60 m where bottom-fixed wind turbines are not feasible. This creates a significant opportunity to couple the high capacity factor floating offshore wind and green hydrogen. In this paper we consider dedicated large-scale floating offshore wind farms for hydrogen production with three coupling typologies; (i) centralised onshore electrolysis (ii) decentralised offshore electrolysis and (iii) centralised offshore electrolysis. The typology design is based on variables including for: electrolyser technology; floating wind platform; and energy transmission vector (electrical power or offshore hydrogen pipelines). Offshore hydrogen pipelines are assessed as economical for large and distant farms. The decentralised offshore typology employing a semi-submersible platform could accommodate a proton exchange membrane electrolyser on deck; this would negate the need for an additional separate structure or hydrogen export compression and enhance dynamic operational ability. It is flexible; if one electrolyser (or turbine) fails hydrogen production can easily continue on the other turbines. It also facilities flexibility in further expansion as it is very much a modular system. Alternatively less complexity is associated with the centralised offshore typology which may employ the electrolysis facility on a separate offshore platform and be associated with a farm of spar-buoy platforms in significant water depth locations.
What is the Energy Balance of Electrofuels Produced Through Power-to-fuel Integration with Biogas Facilities?
Nov 2021
Publication
The need to reduce the climate impact of the transport sector has led to an increasing interest in the utilisation of alternative fuels. Producing advanced fuels through the integration of anaerobic digestion and power-to-fuel technologies may offer a solution to reduce greenhouse gas emissions from difficult to decarbonise modes of transport such as heavy goods vehicles shipping and commercial aviation while also offering wider system benefits. This paper investigates the energy balance of power-to-fuel (power-to-methane power-to-methanol power-to-Fischer-Tropsch fuels) production integrated with a biogas facility co-digesting grass silage and dairy slurry. Through the integration of power-to-methane with anaerobic digestion an increase in system gross energy of 62.6% was found. Power-to-methanol integration with the biogas system increased the gross energy by 50% while power-to-Fischer-Tropsch fuels increased the gross energy yield by 32%. The parasitic energy demand for hydrogen production was highlighted as the most significant factor for integrated biogas and power-to-fuel facilities. Consuming electricity that would otherwise have been curtailed and optimising the anaerobic digestion process were identified as key to improving the energetic efficiency of all system configurations. However the broad cross-sectoral benefits of the overarching cascading circular economy system such as providing electrical grid stability and utilising waste resources must also be considered for a comprehensive perspective on the integration of anaerobic digestion and power-to-fuel.
Achieving Carbon-neutral Iron and Steelmaking in Europe Through the Deployment of Bioenergy with Carbon Capture and Storage
Jan 2019
Publication
The 30 integrated steel plants operating in the European Union (EU) are among the largest single-point CO2 emitters in the region. The deployment of bioenergy with carbon capture and storage (bio-CCS) could significantly reduce their emission intensities. In detail the results demonstrate that CO2 emission reduction targets of up to 20% can be met entirely by biomass deployment. A slow CCS technology introduction on top of biomass deployment is expected as the requirement for emission reduction increases further. Bio-CCS could then be a key technology particularly in terms of meeting targets above 50% with CO2 avoidance costs ranging between €60 and €100 tCO2−1 at full-scale deployment. The future of bio-CCS and its utilisation on a larger scale would therefore only be viable if such CO2 avoidance cost were to become economically appealing. Small and medium plants in particular would economically benefit from sharing CO2 pipeline networks. CO2 transport however makes a relatively small contribution to the total CO2 avoidance cost. In the future the role of bio-CCS in the European iron and steelmaking industry will also be influenced by non-economic conditions such as regulations public acceptance realistic CO2 storage capacity and the progress of other mitigation technologies.
Simulation of Possible Fire and Explosion Hazards of Clean Fuel Vehicles in Garages
Nov 2021
Publication
Clean fuel is advocated to be used for sustainability. The number of liquefied petroleum gas (LPG) and hydrogen vehicles is increasing globally. Explosion hazard is a threat. On the other hand the use of hydrogen is under consideration in Hong Kong. Explosion hazards of these clean fuel (LPG and hydrogen) vehicles were studied and are compared in this paper. The computational fluid dynamics (CFD) software Flame Acceleration Simulator (FLACS) was used. A car garage with a rolling shutter as its entrance was selected for study. Dispersion of LPG from the leakage source with ignition at a higher position was studied. The same garage was used with a typical hydrogen vehicle leaking 3.4 pounds (1.5 kg) of hydrogen in 100 s the mass flow rate being equal to 0.015 kgs−1 . The hydrogen vehicle used in the simulation has two hydrogen tanks with a combined capacity of 5 kg. The entire tank would be completely vented out in about 333 s. Two scenarios of CFD simulation were carried out. In the first scenario the rolling shutter was completely closed and the leaked LPG or hydrogen was ignited at 300 s after leakage. The second scenario was conducted with a gap height of 0.3 m under the rolling shutter. Predicted results of explosion pressure and temperature show that appropriate active fire engineering systems are required when servicing these clean fuel vehicles in garages. An appropriate vent in an enclosed space such as the garage is important in reducing explosion hazards.
Complex Hydrides for Hydrogen Storage – New Perspectives
Apr 2014
Publication
Since the 1970s hydrogen has been considered as a possible energy carrier for the storage of renewable energy. The main focus has been on addressing the ultimate challenge: developing an environmentally friendly successor for gasoline. This very ambitious goal has not yet been fully reached as discussed in this review but a range of new lightweight hydrogen-containing materials has been discovered with fascinating properties. State-of-the-art and future perspectives for hydrogen-containing solids will be discussed with a focus on metal borohydrides which reveal significant structural flexibility and may have a range of new interesting properties combined with very high hydrogen densities.
Climate Change Committee: Progress in Reducing Emissions, 2022 Report to Parliament
Jun 2022
Publication
This statutory report provides a comprehensive overview of the UK Government’s progress to date in reducing emissions. It is accompanied by a new Monitoring Framework which details the CCC’s updated approach to tracking real-world progress through a host of new indicators.<br/>This is a pivotal point in the UK’s journey to Net Zero. The UK is one of the few countries with emissions targets in line with the long-term temperature goal of the Paris Agreement. Policy ambition has moved substantially with the publication of the UK’s Net Zero Strategy. Now is the time to deliver the promised action.
Hydrogen Production in the Swedish Power Sector: Considering Operational Volatilities and Long-term Uncertainties
Nov 2020
Publication
With more renewables on the Swedish electricity market while decommissioning nuclear power plants electricity supply increasingly fluctuates and electricity prices are more volatile. There is hence a need for securing the electricity supply before energy storage solutions become widespread. Electricity price fluctuations moreover affect operating income of nuclear power plants due to their inherent operational inflexibility. Since the anticipated new applications of hydrogen in fuel cell vehicles and steel production producing hydrogen has become a potential source of income particularly when there is a surplus supply of electricity at low prices. The feasibility of investing in hydrogen production was investigated in a nuclear power plant applying Swedish energy policy as background. The analysis applies a system dynamics approach incorporating the stochastic feature of electricity supply and prices. The study revealed that hydrogen production brings alternative opportunities for large-scale electricity production facilities in Sweden. Factors such as hydrogen price will be influential and require in-depth investigation. This study provides guidelines for power sector policymakers and managers who plan to engage in hydrogen production for industrial applications. Although this study was focused upon nuclear power sources it can be extended to hydrogen production from renewable energy sources such as wind and solar.
Simulation of the Inelastic Deformation of Porous Reservoirs Under Cyclic Loading Relevant for Underground Hydrogen Storage
Dec 2022
Publication
Subsurface geological formations can be utilized to safely store large-scale (TWh) renewable energy in the form of green gases such as hydrogen. Successful implementation of this technology involves estimating feasible storage sites including rigorous mechanical safety analyses. Geological formations are often highly heterogeneous and entail complex nonlinear inelastic rock deformation physics when utilized for cyclic energy storage. In this work we present a novel scalable computational framework to analyse the impact of nonlinear deformation of porous reservoirs under cyclic loading. The proposed methodology includes three diferent time-dependent nonlinear constitutive models to appropriately describe the behavior of sandstone shale rock and salt rock. These constitutive models are studied and benchmarked against both numerical and experimental results in the literature. An implicit time-integration scheme is developed to preserve the stability of the simulation. In order to ensure its scalability the numerical strategy adopts a multiscale fnite element formulation in which coarse scale systems with locally-computed basis functions are constructed and solved. Further the efect of heterogeneity on the results and estimation of deformation is analyzed. Lastly the Bergermeer test case—an active Dutch natural gas storage feld—is studied to investigate the infuence of inelastic deformation on the uplift caused by cyclic injection and production of gas. The present study shows acceptable subsidence predictions in this feld-scale test once the properties of the fnite element representative elementary volumes are tuned with the experimental data.
Everything About Hydrogen Podcast: Show Me the Money!
Jul 2020
Publication
This week on the show the team catch up with Alena Fargere Principal at SWEN Capital Partners and a former special advisor to the World Energy Council on Hydrogen projects. As one of the few current project finance funds in Europe with a green gas mandate and a dedicated allocation for investing in hydrogen project finance SWEN Capital Partners provide an invaluable perspective on the challenges and opportunities for hydrogen project investment in Europe and the synergies that exist from Green Gas funds that support biogas and hydrogen opportunities. On the show our hosts discuss the rationale for this fund the profile of projects SWEN are considering and Alena’s broader perspective on the hydrogen market. All this and many more themes this week so don’t miss this episode!
The podcast can be found on their website
The podcast can be found on their website
Everything About Hydrogen Podcast: Electron Stewardship in the Orkney Islands
Nov 2019
Publication
On this weeks episode the team are talking all things hydrogen in the Orkneys with Adele Lidderdale (Hydrogen Officer for Orkney Island Council) and Jon Clipsham (Hydrogen Manager EMEC). While the islands are best known for their exceptional wildlife whisky and cruise ships the Orkney islands have also emerged as a hub for the green hydrogen economy. Working alongside local government community groups research agencies and private sector partners the islands have deployed hydrogen solutions to heat a school power ferries in port move local council workers from A to B and in the future perhaps make Gin?! All this and more on the show.
The podcast can be found on their website
The podcast can be found on their website
Assessment and Recommendations for a Fossil Free Future for Track Work Machinery
Oct 2021
Publication
Current railway track work machinery is mainly operated with diesel fuel. As a result track maintenance of Austrian Federal Railways (OeBB) amounts to nearly 9000 t CO2 equivalent per year according to calculations from Graz University of Technology. OeBB’s total length of railway lines only accounts for 0.56% of the world’s length of lines. This indicates huge potential for mitigating greenhouse gas emissions considering the need for track maintenance worldwide. Environmental concerns have led to the introduction of alternative drives in the transport sector. Until now R&D (Research & Development) of alternative propulsion technologies for track work machinery has been widely neglected. This paper examines the possibility of achieving zero direct emissions during maintenance and construction work in railways by switching to alternative drives. The goal is to analyze alternative propulsion solutions arising from the transport sector and to assess their applicability to track work machinery. Research results together with a calculation tool show that available battery technology is recommendable for energy demands lower than 300 kWh per construction shift. Hydrogen fuel cell technology is an alternative for energy demands higher than 800 kWh. For machinery with energy requirements in between enhancements in battery technology are necessary and desirable for the coming years.
Investigation of Mixing Behavior of Hydrogen Blended to Natural Gas in Gas Network
Apr 2021
Publication
Hydrogen is of great significance for replacing fossil fuels and reducing carbon dioxide emissions. The application of hydrogen mixing with natural gas in gas network transportation not only improves the utilization rate of hydrogen energy but also reduces the cost of large-scale updating household or commercial appliance. This paper investigates the necessity of a gas mixing device for adding hydrogen to existing natural gas pipelines in the industrial gas network. A three-dimensional helical static mixer model is developed to simulate the mixing behavior of the gas mixture. In addition the model is validated with experimental results. Parametric studies are performed to investigate the effect of mixer on the mixing performance including the coefficient of variation (COV) and pressure loss. The research results show that based on the the optimum number of mixing units is three. The arrangement of the torsion angle of the mixing unit has a greater impact on the COV. When the torsion angle θ = 120◦ the COV has a minimum value of 0.66% and when the torsion angle θ = 60◦ the COV has a maximum value of 8.54%. The distance of the mixing unit has little effect on the pressure loss of the mixed gas but has a greater impact on the COV. Consecutive arrangement of the mixing units (Case A) is the best solution. Increasing the distance of the mixing unit is not effective for the gas mixing effect. Last but not least the gas mixer is optimized to improve the mixing performance.
No more items...